emc support matrix · pdf fileemc support matrix emc's policies and requirements for emc...

EMC Support MatrixUnified VNXe-SeriesJuly 2012P/N 300-000-166Rev C35

Copyright EMC Corporation 2012

Copyright © 2001 - 2012 EMC Corporation. All Rights Reserved.

EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice.

EMC, the "EMC2 where information lives" logo and (product name to which the support matrix is directed, i.e. CLARiiON) are either registered trademarks ortrademarks of EMC Corporation in the United States and other countries. For a complete listing of EMC Corporation trademarks, see the EMC Corporationtrademark list at http://www.emc.com/legal/emc-corporation-trademarks.htm.All other trademarks used herein are the property of their respective owners.

Use, copying, and distribution of any EMC software described in this publication requires an applicable software license.

For the most up-to-date listing fo EMC product names, see EMC Corporation Trademarks on EMC.com.

All other trademarks used herein are the property of their respective owners.

EMC Support MatrixEMC's Policies and Requirements for EMC Support Matrix.........................................................................................................................................................1

Storage Array....................................................................................................................................................................................................................................2Base Connectivity.............................................................................................................................................................................................................2

Oracle Solaris...........................................................................................................................................................................................................2Oracle..............................................................................................................................................................................................................2

VMware ESX..........................................................................................................................................................................................................16VMware..........................................................................................................................................................................................................16

ISCSI to FC Routing........................................................................................................................................................................................................17Microsoft Windows 2003 [x64]................................................................................................................................................................................17

Microsoft........................................................................................................................................................................................................17Microsoft Windows 2003 [x86]................................................................................................................................................................................22

Microsoft........................................................................................................................................................................................................22Internet Protocol Addressing Support.............................................................................................................................................................................26Native iSCSI....................................................................................................................................................................................................................27

Apple MAC OSX.....................................................................................................................................................................................................27Apple..............................................................................................................................................................................................................27

Asianux AX [32-Bit]................................................................................................................................................................................................27Asianux..........................................................................................................................................................................................................27

Asianux AX [x86_64]..............................................................................................................................................................................................28Asianux..........................................................................................................................................................................................................28

Citrix Systems, Inc. XenServer...............................................................................................................................................................................29Citrix Systems, Inc.........................................................................................................................................................................................29

Hewlett Packard HP-UX.........................................................................................................................................................................................29Hewlett Packard.............................................................................................................................................................................................29

IBM AIX..................................................................................................................................................................................................................29IBM................................................................................................................................................................................................................29

Microsoft Windows 2003 [x64]................................................................................................................................................................................29Microsoft........................................................................................................................................................................................................29


Microsoft Windows 2008 R2 SP1 [IA64].................................................................................................................................................................33Microsoft........................................................................................................................................................................................................33

Microsoft Windows 2008 R2 SP1 [x64]..................................................................................................................................................................34Microsoft........................................................................................................................................................................................................34

Microsoft Windows 2008 R2 [x64]..........................................................................................................................................................................35Microsoft........................................................................................................................................................................................................35



Novell Netware.......................................................................................................................................................................................................38Novell.............................................................................................................................................................................................................38

Oracle Linux UEK [x86_64]....................................................................................................................................................................................38Oracle............................................................................................................................................................................................................38

Oracle Linux [32-Bit]...............................................................................................................................................................................................40Oracle............................................................................................................................................................................................................40

Oracle Linux [x86_64]............................................................................................................................................................................................41Oracle............................................................................................................................................................................................................41

Oracle Solaris.........................................................................................................................................................................................................43Oracle............................................................................................................................................................................................................43

Red Hat RHEL [32-Bit]...........................................................................................................................................................................................44Red Hat..........................................................................................................................................................................................................44

Red Hat RHEL [AMD-64]........................................................................................................................................................................................48Red Hat..........................................................................................................................................................................................................48

Red Hat RHEL [EM64T].........................................................................................................................................................................................48Red Hat..........................................................................................................................................................................................................48

Red Hat RHEL [IA64].............................................................................................................................................................................................49Red Hat..........................................................................................................................................................................................................49

Red Hat RHEL [x86_64].........................................................................................................................................................................................49Red Hat..........................................................................................................................................................................................................49


SuSE SLES [32-Bit]................................................................................................................................................................................................54SuSE..............................................................................................................................................................................................................54

SuSE SLES [IA64]..................................................................................................................................................................................................56SuSE..............................................................................................................................................................................................................56

SuSE SLES [x86_64].............................................................................................................................................................................................56SuSE..............................................................................................................................................................................................................56

VMware ESX..........................................................................................................................................................................................................59VMware..........................................................................................................................................................................................................59

VMware ESXi.........................................................................................................................................................................................................60VMware..........................................................................................................................................................................................................60

Path Management Software............................................................................................................................................................................................61Asianux AX [32-Bit]................................................................................................................................................................................................61

Asianux..........................................................................................................................................................................................................61Asianux AX [x86_64]..............................................................................................................................................................................................61

Asianux..........................................................................................................................................................................................................61Microsoft Windows 2003 [x64]................................................................................................................................................................................61


Microsoft........................................................................................................................................................................................................62Microsoft Windows 2008 R2 SP1 [x64]..................................................................................................................................................................62

Microsoft........................................................................................................................................................................................................62Microsoft Windows 2008 R2 [x64]..........................................................................................................................................................................62



Microsoft........................................................................................................................................................................................................63Oracle Linux UEK [x86_64]....................................................................................................................................................................................63

Oracle............................................................................................................................................................................................................63Oracle Linux [32-Bit]...............................................................................................................................................................................................63

Oracle............................................................................................................................................................................................................63Oracle Linux [x86_64]............................................................................................................................................................................................64

Oracle............................................................................................................................................................................................................64Oracle Solaris.........................................................................................................................................................................................................64

Oracle............................................................................................................................................................................................................64Red Hat RHEL [32-Bit]...........................................................................................................................................................................................64

Red Hat..........................................................................................................................................................................................................64Red Hat RHEL [IA64].............................................................................................................................................................................................65

EMC Support MatrixStorage Array

Red Hat..........................................................................................................................................................................................................65Red Hat RHEL [x86_64].........................................................................................................................................................................................65

Red Hat..........................................................................................................................................................................................................65Red Hat RHEL [x86_84].........................................................................................................................................................................................66

Red Hat..........................................................................................................................................................................................................66SuSE SLES [32-Bit]................................................................................................................................................................................................66

SuSE..............................................................................................................................................................................................................66SuSE SLES [x86_64].............................................................................................................................................................................................66

SuSE..............................................................................................................................................................................................................66VMware ESX..........................................................................................................................................................................................................66

VMware..........................................................................................................................................................................................................66VMware ESXi.........................................................................................................................................................................................................67

VMware..........................................................................................................................................................................................................67Providers.........................................................................................................................................................................................................................67

Red Hat RHEL [32-Bit]...........................................................................................................................................................................................67Red Hat..........................................................................................................................................................................................................67


SuSE SLES [x86_64].............................................................................................................................................................................................68SuSE..............................................................................................................................................................................................................68

Replication Manager Block Storage................................................................................................................................................................................68Veritas Volume Manager.................................................................................................................................................................................................68



Microsoft Windows 2008 R2 SP1 [IA64].................................................................................................................................................................69Microsoft........................................................................................................................................................................................................69





Oracle Linux [x86_64]............................................................................................................................................................................................74Oracle............................................................................................................................................................................................................74

Oracle Solaris.........................................................................................................................................................................................................74Oracle............................................................................................................................................................................................................74


SuSE SLES [x86_64].............................................................................................................................................................................................76SuSE..............................................................................................................................................................................................................76

WAN Optimization Controllers........................................................................................................................................................................................77iSCSI Clusters.................................................................................................................................................................................................................78







EMC's Policies and Requirements for EMC Support Matrix

EMC's Support Matrix Policies and Requirements

This section describes EMC's policies and requirements for the EMC Support Matrix document.

Purpose and Limitations of this Document

This document is being provided for informational purposes only and may change at any time. This version supersedes and replaces all previous versions. Theinformation is to serve only as a guide for those configurations/products that EMC has qualified. The information in this document is a subset of the informationthat can be found on the E-Lab Interoperability Navigator tool which is available for all EMC personnel, customers and partners. The E-Lab InteroperabilityNavigator site may be reached at http://elabnavigator.emc.com.

The information included in this document is intended as a guide in the configuration of systems for EMC's products. It is not intended to be the sole resourcefor system configuration. For more information or answers to questions not found in this document, please see EMC's website, other EMC documentation,relevant vendor documentation, or contact your EMC Sales or EMC Customer Service representative.For a complete listing of any known issues with the current support matrix content, please review the ESM Errata on E-Lab Interoperability Navigator. To reportany issues with the content contained within the support matrix, follow the steps documented on the Contacts link on E-Lab Interoperability Navigator. E-LabInteroperability Navigator can be reached at http://elabnavigator.emc.com.

Policies for Qualifying Systems

Policies and procedures for support of EMC products are set forth in the customer's applicable agreements. EMC's publication of information relating to systemconfigurations covers only those outlined in this document or by approval from EMC Engineering. Other system configurations not found in this document arenot qualified without EMC Engineering approval. EMC has qualified hardware and software provided only by the vendors listed in this document, and hostsystems, hardware and software from other vendors are not qualified, and may never be. Please contact your EMC Sales or EMC Customer Servicerepresentative for updates or information not included in this document.

EMC maintains a large collection of the products listed above as well as third-party application software for qualification with EMC's storage systems and tosimulate customer environments, but you must consult the vendors for information about their system internals, such as hardware and associated drivers.

Policy for Future Qualification of Operating System Software Releases

The information in this document is maintained by EMC and EMC strives to update this document with new releases of hardware, operating systems, firmware,BIOS, switch software, etc., as they become available from the vendors. EMC works with the vendors during their development and release processes in orderto be fully informed at the time the vendors release new versions. EMC does not announce qualification prior to vendors' General Availability. In some cases,EMC may choose to perform regression testing following the vendors' GA; in these cases and in cases where advance preparation is not possible, EMC mayvalidate and qualify vendors' products as appropriate after they have been released. For early support of such products, including vendor beta participation,contact your EMC Sales or EMC Customer Service representative.

Policy for End-of-Life Support

EMC strives to continue support for any installed platforms, but may remove support from this host matrix for new installations within three months after thevendor has announced that this platform has reached the end of life. EMC will continue support for existing installations of hardware, operating systems, andcomponents that the vendor has officially declared to have reached end of life as long as support is available from the vendor. For the full list of EMC productend of life and end of support, please see the "Release and End of Life Dates" pages on the Support section of Powerlink.

07/01/2012 1 EMC's Policies and Requirements for EMC Support Matrix

Storage ArrayBase ConnectivityConfiguration Notes

Starting with Symmetrix VMAX, Unified and CLARiiON CX4, minimum link speed supported for Fibre Channel direct connection is 2Gb/s.

EMC supports Symmetrix and CLARiiON configured as a boot device for the servers where listed below, provided that these requirements are followed. Thiswill ensure the best possible response times for boot/root/swap volumes.

EMC recommends shutting down the host server during maintenance procedures that could cause the boot disk to become unavailable to the host. If thepaging file is unavailable to the operating system, a crash can occur. EMC supports online microcode upgrades for Windows systems booting from Symmetrixand non-disruptive upgrades (NDU) for Windows systems booting from CLARiiON arrays. Refer to the specific OS Host Connectivity Guide for best practices.

Any issues that arise when trying to use the boot LUN on a host that is not identical to the source host is outside the scope of what EMC can support. In caseof environment failure where I/O is not written back to the source LUN, or if the source LUN is not left in a stable state by the source host, the source LUN, orany replicated LUN of the source, is not guaranteed to be usable.

Oracle SolarisOracleNEC

NEC

No.Host

SystemOperating

System Host Bus

MinimumOS

Revision Host Bus Adapter TopologyStorageArray

ExternalBoot

1 NECCX5000:F490, F890

OracleSolaris 10SPARC5, 10,11, 12, 13, 14,15, 34, 35, 36,37

PCI S10Update 3(11/06)5

Emulex LP9002-E (LP9002L-E)2, 3, 6, 29, 66, 89, 90, 93, 94, 95, 97, 98 FC-AL,FC-SW

EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y38, 39,41, 42, 43,44, 45, 52

2 NECCX5000F890



Emulex: LPe11000-E-G2, 3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2,3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe12000-E-G2, 3, 6, 18, 29, 47, 48, 49, 50,51, LPe12000-E2, 3, 6, 18, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW

EMC UnifiedStorageVNXe3300(File/iSCSI)

Y38, 39,41, 42, 43,44, 45, 52

3 NECCX5000F490



Emulex: LPe11000-E-G2, 3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2,3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe12000-E2, 3, 6, 18, 29, 47, 48, 49, 50, 51,LPe12000-E-G2, 3, 6, 18, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

4 NECCX5000:F490, F890



Emulex: LPe11000-E2, 3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe11000-E-G2,3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe12002-E-G2, 3, 6, 18, 29, 47, 48, 49, 50,51, LPe12002-E2, 3, 6, 18, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

5 NECCX5000F890




FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

6 NECCX5000F490



Emulex: LPe11002-E-G2, 3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe11002-E2,3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe12000-E2, 3, 6, 18, 29, 47, 48, 49, 50, 51,LPe12000-E-G2, 3, 6, 18, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

7 NECCX5000:F490, F890




FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

8 NECCX5000:F490, F890



Oracle: SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)2, 3,18, 29, 53, 55, 58, 59, 64, 65, 66,SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N (QLE2460)18, 20, 22, 25,58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4 (LPe11002-S)2, 3, 18, 29,53, 55, 58, 59, 64, 65, 66, SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N(QLE2462)18, 20, 22, 25, 58, 59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

9 NECCX5000:F490, F890



Oracle: SG-XPCIE1FC-EM8-Z/SG-XPCIE1FC-EM8-N(LPe12000-S)2, 3, 6, 29, 50, 55, 58, 59,SG-XPCIE2FC-EM8-Z/SG-XPCIE2FC-EM8-N (LPe12002-S)2, 3, 6, 29,50, 55, 58, 59

FC-AL,FC-SW


Y38, 43,44

10 NECCX5000:F490, F890



Oracle: SG-XPCIE1FC-QF8-Z/SG-XPCIE1FC-QF8-N (QLE2560)6, 20,22, 25, 58, 59, 60, 61, SG-XPCIE2FC-QF8-Z/SG-XPCIE2FC-QF8-N(QLE2562)6, 20, 22, 25, 58, 59, 61

FC-AL,FC-SW


Y38, 39,45

11 NECCX5000:F490, F890



QLogic: QLE2460-E-SP6, 18, 20, 22, 24, 25, 32, 46, 70, QLE2462-E-SP6,20, 22, 24, 25, 32, 33, 46, QLE2560-E-SP6, 18, 20, 22, 24, 25, 62, 63,QLE2562-E-SP6, 18, 20, 22, 24, 25, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

07/01/2012 2 Storage Array

12 NECCX5000 E:T5140,T5240


PCIExpress

S10Update 4(08/07)5

Emulex: LPe11000-E-G2, 3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2,3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe11002-E-G2, 3, 6, 18, 29, 50, 53, 54, 55,56, 57, LPe11002-E2, 3, 6, 18, 29, 50, 53, 54, 55, 56, 57, LPe12000-E-G2, 3,6, 18, 29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 18, 29, 47, 48, 49, 50, 51,LPe12002-E-G2, 3, 6, 18, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6, 18, 29,47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

13 NECCX5000 E:T5120,T5220


PCIExpress

S10Update 4(08/07)5

Emulex: LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57,LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe12000-E-G2, 3, 6, 29, 47,48, 49, 50, 51, LPe12000-E2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E-G2, 3,6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

14 NECCX5000 E:T5120,T5220


PCIExpress

S10Update 4(08/07)5

Emulex: LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57,LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe12000-E2, 3, 6, 29, 47, 48,49, 50, 51, LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E-G2, 3,6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

15 NECCX5000 E:T5140,T5240


PCIExpress

S10Update 4(08/07)5

Oracle: SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)2, 3,18, 29, 53, 55, 58, 59, 64, 65, 66,SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N (QLE2460)18, 20, 22, 25,58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4 (LPe11002-S)2, 3, 18, 29,53, 55, 58, 59, 64, 65, 66, SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N(QLE2462)18, 20, 22, 25, 58, 59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

16 NECCX5000 E:T5120,T5220


PCIExpress

S10Update 4(08/07)5

Oracle: SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)2, 3,29, 53, 55, 58, 59, 64, 65, 66, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)20, 22, 25, 58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4(LPe11002-S)2, 3, 29, 53, 55, 58, 59, 64, 65, 66,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)20, 22, 25, 58,59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

17 NECCX5000 E:T5120,T5140,T5220,T5240


PCIExpress

S10Update 4(08/07)5


FC-AL,FC-SW


Y38, 43,44

18 NECCX5000 E:T5120,T5140,T5220,T5240


PCIExpress

S10Update 4(08/07)5


FC-AL,FC-SW


Y38, 39,45

19 NECCX5000 E:T5140,T5240


PCIExpress

S10Update 4(08/07)5

QLogic: QLE2460-E-SP6, 18, 20, 22, 24, 25, 32, 46, 70, QLE2462-E-SP6,18, 20, 22, 24, 25, 32, 33, 46, QLE2560-E-SP6, 18, 20, 22, 24, 25, 62, 63,QLE2562-E-SP6, 18, 20, 22, 24, 25, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

20 NECCX5000 E:T5120,T5220


PCIExpress

S10Update 4(08/07)5

QLogic: QLE2460-E-SP6, 20, 22, 24, 25, 32, 46, 70, QLE2462-E-SP6, 20,22, 24, 25, 32, 33, 46, QLE2560-E-SP6, 20, 22, 24, 25, 62, 63,QLE2562-E-SP6, 20, 22, 24, 25, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

21 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

S10Update 3(11/06)5

Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP9002-E(LP9002L-E)2, 3, 6, 29, 66, 89, 90, 93, 94, 95, 97, 98, LPe11000-E-G2, 3, 6,29, 50, 53, 54, 55, 56, 57, LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57,LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E2, 3, 6, 29, 50,53, 54, 55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

22 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

S10Update 3(11/06)5

Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP9002-E(LP9002L-E)2, 3, 6, 29, 66, 89, 90, 93, 94, 95, 97, 98, LPe11002-E-G2, 3, 6,29, 50, 53, 54, 55, 56, 57, LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57,LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 29, 47, 48,49, 50, 51, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6,29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

23 NECCX5000 E:M400016,M500016,M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

Emulex: LP11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65,LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2, 3, 6, 29, 50,53, 54, 55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

24 NECCX5000 E:M400016,M500016,M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

Emulex: LP11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65,LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 29, 47, 48,49, 50, 51, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6,29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

25 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

Emulex: LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57,LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

26 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

Emulex: LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12000-E2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E-G2, 3, 6, 29, 47, 48,49, 50, 51, LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

27 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

S10Update 3(11/06)5

Oracle: SG-XPCI1FC-EM2 (LP10000)2, 3, 29, 53, 55, 58, 59, 66,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)20, 22, 25, 58, 59,65, 67, 68, 69, SG-XPCI2FC-EM2 (LP10000DC)2, 3, 29, 53, 55, 58, 59, 66,SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N (QLE2460)20, 22, 25, 58,59, 64, 65, 67, 68, 69, SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N(QLE2462)20, 22, 25, 58, 59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

28 NECCX5000 E:M400016,M500016,M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

Oracle: SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)2, 3,6, 29, 50, 53, 55, 58, 59, 65, 66,SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N (LP11000-S)2, 3, 29, 50, 53,55, 58, 59, 65, 66, SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N(LP11002-S)2, 3, 6, 29, 50, 53, 55, 58, 59, 65, 66,SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N (LP11002-S)2, 3, 29, 50, 53,55, 58, 59, 65, 66, SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N(LPe11000-S)2, 3, 29, 53, 55, 58, 59, 64, 65, 66, SG-XPCIE2FC-EM4(LPe11002-S)2, 3, 29, 53, 55, 58, 59, 64, 65, 66

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

Storage Array


29 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

S10Update 3(11/06)5

Oracle: SG-XPCI2FC-QF2-Z (X6768A)6, 20, 22, 25, 58, 59, 77, 99,SG-XPCIE1FC-QF8-Z/SG-XPCIE1FC-QF8-N (QLE2560)6, 20, 22, 25,58, 59, 60, 61, SG-XPCIE2FC-QF8-Z/SG-XPCIE2FC-QF8-N(QLE2562)6, 20, 22, 25, 58, 59, 61, X6768A (SG-XPCI2FC-QF2)6, 20, 22,25, 58, 75, 76, 77

FC-AL,FC-SW


Y38, 39,45

30 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 43,44

31 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

S10Update 3(11/06)5

QLogic: QLA2340-E-SP6, 20, 22, 25, 82, 83, 84, 86, 87, 88,QLA2342-E-SP6, 20, 22, 25, 82, 83, 84, 85, 86, 87, QLA2460-E-SP6, 20, 22,24, 25, 33, 46, 64, 65, 80, QLA2462-E-SP6, 20, 22, 24, 25, 33, 46, 64, 65, 80,QLE2460-E-SP6, 20, 22, 24, 25, 32, 46, 70, QLE2462-E-SP6, 20, 22, 24, 25,32, 33, 46

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

32 NECCX5000 E:M400016,M500016,M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

QLogic: QLE2560-E-SP6, 20, 22, 24, 25, 62, 63, QLE2562-E-SP6, 20, 22,24, 25, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

33 NECCX5000:F20K,F2900,F490,F4900,F6900,F890

OracleSolaris 10SPARC5, 10,11, 12, 13, 14,15, 34, 35, 36,37, 71, 72, 73,74

PCI Solaris 10(03/05)5

Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 64, 66, 81, 89, 90, 91, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 64, 81, 89, 90, 91, 92, 95, 96,LP11000-E2, 3, 29, 50, 53, 54, 55, 56, 57, 64, 65, LP11002-E2, 3, 6, 29, 50,53, 54, 55, 56, 57, 64, 65

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

34 NECCX5000:F20K,F2900,F490,F4900,F6900,F890



Oracle: SG-XPCI1FC-EM2 (LP10000)2, 3, 29, 53, 55, 58, 59, 66, 81,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)2, 3, 6, 29,50, 53, 55, 58, 59, 65, 66, SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N(LP11000-S)2, 3, 29, 50, 53, 55, 58, 59, 65, 66,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)20, 22, 25, 58, 59,65, 67, 68, 69, SG-XPCI2FC-EM2 (LP10000DC)2, 3, 29, 53, 55, 58, 59, 66,81, SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N (LP11002-S)2, 3, 6,29, 50, 53, 55, 58, 59, 65, 66, SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N(LP11002-S)2, 3, 29, 50, 53, 55, 58, 59, 65, 66

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

35 NECCX5000:F20K,F2900,F490,F4900,F6900,F890



Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 20, 22, 25, 58, 59, 77, 79,SG-XPCI2FC-QF2-Z (X6768A)6, 20, 22, 25, 58, 59, 77, 79, X6768A(SG-XPCI2FC-QF2)6, 20, 22, 25, 58, 64, 75, 76, 77, 78

FC-AL,FC-SW


Y38, 39,45

36 NECCX5000:F20K,F2900,F490,F4900,F6900,F890



QLogic: QLA2340-E-SP6, 20, 22, 25, 82, 83, 84, 86, 87, 88,QLA2342-E-SP6, 20, 22, 25, 82, 83, 84, 85, 86, 87, QLA2460-E-SP6, 20, 22,24, 25, 33, 46, 64, 65, 80, QLA2462-E-SP6, 20, 22, 24, 25, 33, 46, 64, 65, 80

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

37 NECCX5000:F490, F890

OracleSolaris 10SPARC5, 10,11, 12, 13, 14,15, 34, 35, 36,37, 72, 73, 74


Emulex LP11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65 FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

38 NECCX5000:F490, F890



Oracle SG-XPCI1FC-QL2 (QLA2340)6, 20, 22, 25, 58, 59, 77, 79, 99 FC-AL,FC-SW


Y38, 39,45

39 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5



Y38, 39,41, 42, 43,44, 45, 52

40 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5



Y38, 39,45

41 NECCX5000:F490, F890

OracleSolaris 10SPARC5, 10,11, 12, 13, 14,15, 34, 35, 36,37, 72, 74


Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP11002-E2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56,57, LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe12002-E-G2, 3, 6, 29,47, 48, 49, 50, 51, LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

42 NECCX5000:F490, F890



Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP11002-E2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56,57, LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe12000-E-G2, 3, 6, 29,47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

43 NECCX5000F490



Emulex: LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11000-E2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

Storage Array


44 NECCX5000F890



Emulex: LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11000-E-G2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

45 NECCX5000F490



Emulex: LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12000-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

46 NECCX5000F890



Emulex: LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E2, 3,6, 29, 50, 53, 54, 55, 56, 57, LPe12000-E2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

47 NECCX5000:F490, F890



Oracle: SG-XPCI1FC-EM2 (LP10000)2, 3, 29, 53, 55, 58, 59, 66,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)2, 3, 6, 29,50, 53, 55, 58, 59, 65, 66, SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N(LP11000-S)2, 3, 29, 50, 53, 55, 58, 59, 65, 66,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)20, 22, 25, 58, 59,65, 67, 68, 69, SG-XPCI2FC-EM2 (LP10000DC)2, 3, 29, 53, 55, 58, 59, 66,SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N (LP11002-S)2, 3, 6, 29,50, 53, 55, 58, 59, 65, 66, SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N(LP11002-S)2, 3, 29, 50, 53, 55, 58, 59, 65, 66,SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)2, 3, 29, 53,55, 58, 59, 64, 65, 66, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)20, 22, 25, 58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4(LPe11002-S)2, 3, 29, 53, 55, 58, 59, 64, 65, 66,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)20, 22, 25, 58,59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

48 NECCX5000:F490, F890




FC-AL,FC-SW


Y38, 39,45

49 NECCX5000:F490, F890




FC-AL,FC-SW


Y38, 43,44

50 NECCX5000:F490, F890



QLogic: QLA2340-E-SP6, 20, 22, 25, 82, 83, 84, 86, 87, 88,QLA2342-E-SP6, 20, 22, 25, 82, 83, 84, 85, 86, 87, QLA2460-E-SP6, 20, 22,24, 25, 33, 46, 64, 65, 80, QLA2462-E-SP6, 20, 22, 24, 25, 33, 46, 64, 65, 80,QLE2460-E-SP6, 20, 22, 24, 25, 32, 46, 70, QLE2462-E-SP6, 20, 22, 24, 25,32, 33, 46, QLE2560-E-SP6, 20, 22, 24, 25, 62, 63, QLE2562-E-SP6, 20, 22,24, 25, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

51 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5

Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP11002-E2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56,57, LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E-G2, 3, 6, 29,50, 53, 54, 55, 56, 57, LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57,LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 29, 47, 48,49, 50, 51, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6,29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

52 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

53 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5


FC-AL,FC-SW


Y38, 39,45

54 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5


FC-AL,FC-SW


Y38, 43,44

55 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5


FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

56 NECCX5000 E:M400016,M500016,M8000,M9000

OracleSolaris 10SPARC5, 10,11, 12, 13, 14,15, 34, 35, 36,37, 73

PCIExpress,PCI-X

S10Update 3(11/06)5



Y38, 39,41, 42, 43,44, 45, 52

57 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

S10Update 3(11/06)5



Y38, 39,45

Storage Array


58 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

Oracle: SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)20, 22, 25,58, 59, 67, 68, 69, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)20, 22, 25, 58, 59, 67, 68, 69,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)20, 22, 25, 58,59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

59 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 43,44

60 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 39,45

61 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

QLogic: QLA2460-E-SP6, 20, 22, 24, 25, 33, 46, 80, QLA2462-E-SP6, 20,22, 24, 25, 33, 46, 80, QLE2460-E-SP6, 20, 22, 24, 25, 32, 46, 70,QLE2462-E-SP6, 20, 22, 24, 25, 32, 33, 46

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

62 NECCX5000:F490, F890





Y38, 39,41, 42, 43,44, 45, 52

63 NECCX5000:F490, F890



Oracle: SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)20, 22, 25,58, 59, 65, 67, 68, 69, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)20, 22, 25, 58, 59, 64, 65, 67, 68, 69,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)20, 22, 25, 58,59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

64 NECCX5000:F490, F890



Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 20, 22, 25, 58, 59, 77, 79, 99,SG-XPCIE1FC-QF8-Z/SG-XPCIE1FC-QF8-N (QLE2560)6, 20, 22, 25,58, 59, 60, 61, SG-XPCIE2FC-QF8-Z/SG-XPCIE2FC-QF8-N(QLE2562)6, 20, 22, 25, 58, 59, 61

FC-AL,FC-SW


Y38, 39,45

65 NECCX5000:F490, F890




FC-AL,FC-SW


Y38, 43,44

66 NECCX5000:F490, F890



QLogic: QLA2460-E-SP6, 20, 22, 24, 25, 33, 46, 64, 65, 80,QLA2462-E-SP6, 20, 22, 24, 25, 33, 46, 64, 65, 80, QLE2460-E-SP6, 20, 22,24, 25, 32, 46, 64, 65, 70, QLE2462-E-SP6, 20, 22, 24, 25, 32, 33, 46, 64, 65

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

67 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5



Y38, 39,41, 42, 43,44, 45, 52

68 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5



Y38, 39,45

69 NECCX5000:F490, F890



Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP11002-E2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56,57, 64, 65, LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65,LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

70 NECCX5000:F490, F890



Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP11002-E2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E-G2, 3, 6, 29, 50, 53, 54, 55, 56,57, 64, 65, LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

71 NECCX5000F490



Emulex: LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65,LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65, LPe12000-E-G2, 3, 6,29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6, 29, 47, 48,49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

72 NECCX5000F890



Emulex: LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65,LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65, LPe12000-E2, 3, 6, 29,47, 48, 49, 50, 51, LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6, 29, 47, 48,49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

73 NECCX5000F890



Emulex: LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6,29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

74 NECCX5000F490



Emulex: LPe12000-E2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12000-E-G2, 3, 6,29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

Storage Array


75 NECCX5000:F490, F890



Oracle: SG-XPCI1FC-EM2 (LP10000)2, 3, 29, 53, 55, 58, 59, 66,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)2, 3, 6, 29,50, 53, 55, 58, 59, 65, 66, SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N(LP11000-S)2, 3, 29, 50, 53, 55, 58, 59, 65, 66, SG-XPCI2FC-EM2(LP10000DC)2, 3, 29, 53, 55, 58, 59, 66,SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N (LP11002-S)2, 3, 6, 29,50, 53, 55, 58, 59, 65, 66, SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N(LP11002-S)2, 3, 29, 50, 53, 55, 58, 59, 65, 66,SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)2, 3, 29, 53,55, 58, 59, 64, 65, 66, SG-XPCIE2FC-EM4 (LPe11002-S)2, 3, 29, 53, 55,58, 59, 64, 65, 66

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

76 NECCX5000:F490, F890



Oracle: SG-XPCI2FC-QF2-Z (X6768A)6, 20, 22, 25, 58, 59, 77, 99,X6768A (SG-XPCI2FC-QF2)6, 20, 22, 25, 58, 75, 76, 77

FC-AL,FC-SW


Y38, 39,45

77 NECCX5000:F490, F890



QLogic: QLA2340-E-SP6, 20, 22, 25, 82, 83, 84, 86, 87, 88,QLA2342-E-SP6, 20, 22, 25, 82, 83, 84, 85, 86, 87, QLE2560-E-SP6, 20, 22,24, 25, 62, 63, QLE2562-E-SP6, 20, 22, 24, 25, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

78 NECCX5000: ET100017, FT100017


PCIExpress

S10Update 3(11/06)5

Emulex: LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65,LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E-G2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57,64, 65, LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 29,47, 48, 49, 50, 51, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51,LPe12002-E2, 3, 6, 29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

79 NECCX5000: ET100017, FT100017


PCIExpress

S10Update 3(11/06)5

Oracle: SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)2, 3,29, 53, 55, 58, 59, 64, 65, 66, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)20, 22, 25, 58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4(LPe11002-S)2, 3, 29, 53, 55, 58, 59, 64, 65, 66,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)20, 22, 25, 58,59, 64, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

80 NECCX5000: ET100017, FT100017


PCIExpress

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 43,44

81 NECCX5000: ET100017, FT100017


PCIExpress

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 39,45

82 NECCX5000: ET100017, FT100017


PCIExpress

S10Update 3(11/06)5

QLogic: QLE2460-E-SP6, 20, 22, 24, 25, 32, 46, 64, 65, 70,QLE2462-E-SP6, 20, 22, 24, 25, 32, 33, 46, 64, 65, QLE2560-E-SP6, 20, 22,24, 25, 62, 63, QLE2562-E-SP6, 20, 22, 24, 25, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

83 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5

Emulex: LP10000-E2, 3, 6, 29, 50, 53, 55, 66, 81, 89, 90, 92, 95, 96,LP10000DC-E2, 3, 6, 29, 50, 53, 55, 81, 89, 90, 92, 95, 96, LP11002-E2, 3, 6,29, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E-G2, 3, 6, 29, 50, 53, 54, 55, 56,57, LPe11000-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57, LPe11002-E-G2, 3, 6, 29,50, 53, 54, 55, 56, 57, LPe11002-E2, 3, 6, 29, 50, 53, 54, 55, 56, 57,LPe12000-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12000-E2, 3, 6, 29, 47, 48,49, 50, 51, LPe12002-E-G2, 3, 6, 29, 47, 48, 49, 50, 51, LPe12002-E2, 3, 6,29, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

84 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

85 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 39,45

86 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 43,44

87 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

88 NECCX5000 E:M400016,M500016

OracleSolaris 10SPARC5, 10,11, 12, 13, 14,15, 34, 35, 37

PCIExpress,PCI-X

S10Update 3(11/06)5

Oracle SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)20, 22, 25,58, 59, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

Storage Array


89 NECCX5000:F20K,F2900,F490,F4900,F6900,F890



Emulex: LP9002-E (LP9002L-E)2, 3, 6, 29, 64, 66, 81, 89, 90, 93, 94, 95, 97,98, LP9802-E2, 3, 6, 29, 64, 66, 81, 89, 90, 91, 92, 93, 94, 95, 96

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

90 NECCX5000:F20K,F2900,F490,F4900,F6900,F890




FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

91 NECCX5000:F20K,F2900,F490,F4900,F6900,F890



Oracle X6767A (SG-XPCI1FC-QF2)6, 20, 22, 25, 58, 64, 75, 77, 78, 99 FC-AL,FC-SW


Y38, 39,45

92 NECCX5000:F490, F890




FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

93 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

S10Update 2(06/06)5


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

94 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

S10Update 3(11/06)5

Oracle SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)20, 22, 25,58, 59, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

95 NECCX5000:F490, F890




FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

96 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X

S10Update 3(11/06)5


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

97 NECCX5000:F20K,F2900,F490,F4900,F6900,F890

OracleSolaris 11SPARC100

PCI Emulex: LP10000-E6, 50, 53, 55, 64, 66, 81, 91, 92, 96, LP10000DC-E6, 50,53, 55, 64, 81, 91, 92, 96, LP11000-E50, 53, 54, 55, 56, 57, 64, 65,LP11002-E6, 50, 53, 54, 55, 56, 57, 64, 65, LP9002-E (LP9002L-E)6, 64, 66,81, 93, 94, 97, 98, LP9802-E6, 64, 66, 81, 91, 92, 93, 94, 96

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

98 NECCX5000:F490, F890


PCI Emulex: LP10000-E6, 50, 53, 55, 66, 81, 92, 96, LP10000DC-E6, 50, 53, 55,81, 92, 96, LP11000-E6, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E-G6, 18,50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E6, 18, 50, 53, 54, 55, 56, 57, 64, 65,LPe11002-E-G6, 18, 50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E6, 18, 50, 53,54, 55, 56, 57, 64, 65, LPe12002-E-G6, 18, 47, 48, 49, 50, 51, LPe12002-E6,18, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

99 NECCX5000:F490, F890


PCI Emulex: LP10000-E6, 50, 53, 55, 66, 81, 92, 96, LP10000DC-E6, 50, 53, 55,81, 92, 96, LP11000-E6, 50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E-G6, 18,50, 53, 54, 55, 56, 57, 64, 65, LPe11002-E6, 18, 50, 53, 54, 55, 56, 57, 64, 65,LPe12002-E-G6, 18, 47, 48, 49, 50, 51, LPe12002-E6, 18, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

100 NECCX5000F490


PCI Emulex: LPe11000-E-G6, 18, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E6,18, 50, 53, 54, 55, 56, 57, 64, 65, LPe12000-E-G6, 18, 47, 48, 49, 50, 51,LPe12000-E6, 18, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

101 NECCX5000F890


PCI Emulex: LPe11000-E-G6, 18, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E6,18, 50, 53, 54, 55, 56, 57, 64, 65, LPe12000-E6, 18, 47, 48, 49, 50, 51,LPe12000-E-G6, 18, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

102 NECCX5000F490


PCI Emulex: LPe12000-E-G6, 18, 47, 48, 49, 50, 51, LPe12000-E6, 18, 47, 48,49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

103 NECCX5000F890


PCI Emulex: LPe12000-E6, 18, 47, 48, 49, 50, 51, LPe12000-E-G6, 18, 47, 48,49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

104 NECCX5000:F20K,F2900,F490,F4900,F6900,F890


PCI Oracle: SG-XPCI1FC-EM2 (LP10000)53, 55, 58, 59, 66, 81,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)6, 50, 53, 55,58, 59, 65, 66, SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N(LP11000-S)50, 53, 55, 58, 59, 65, 66,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)58, 59, 65, 67, 68,69, SG-XPCI2FC-EM2 (LP10000DC)53, 55, 58, 59, 66, 81,SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N (LP11002-S)6, 50, 53, 55,58, 59, 65, 66, SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N(LP11002-S)50, 53, 55, 58, 59, 65, 66,SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)58, 59, 65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

Storage Array


105 NECCX5000:F490, F890


PCI Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 58, 59, 77, 79, 99,SG-XPCI2FC-QF2-Z (X6768A)6, 58, 59, 77, 99,SG-XPCIE1FC-QF8-Z/SG-XPCIE1FC-QF8-N (QLE2560)6, 58, 59, 60,61, SG-XPCIE2FC-QF8-Z/SG-XPCIE2FC-QF8-N (QLE2562)6, 58, 59,61

FC-AL,FC-SW


Y38, 39,45

106 NECCX5000:F20K,F2900,F490,F4900,F6900,F890


PCI Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 58, 59, 77, 79,SG-XPCI2FC-QF2-Z (X6768A)6, 58, 59, 77, 79, X6767A(SG-XPCI1FC-QF2)6, 58, 64, 75, 77, 78, 99, 107, X6768A(SG-XPCI2FC-QF2)6, 58, 64, 75, 76, 77, 78

FC-AL,FC-SW


Y38, 39,45

107 NECCX5000:F490, F890


PCI Oracle: SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)18,53, 55, 58, 59, 64, 65, 66, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)18, 58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4(LPe11002-S)18, 53, 55, 58, 59, 64, 65, 66,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)18, 58, 59, 64,65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

108 NECCX5000:F490, F890


PCI Oracle: SG-XPCIE1FC-EM8-Z/SG-XPCIE1FC-EM8-N(LPe12000-S)6, 50, 55, 58, 59,SG-XPCIE2FC-EM8-Z/SG-XPCIE2FC-EM8-N (LPe12002-S)6, 50, 55,58, 59

FC-AL,FC-SW


Y38, 43,44

109 NECCX5000:F20K,F2900,F490,F4900,F6900,F890


PCI QLogic: QLA2340-E-SP6, 82, 83, 88, QLA2342-E-SP6, 82, 83, 85,QLA2460-E-SP6, 24, 33, 46, 64, 65, 80, QLA2462-E-SP6, 24, 33, 46, 64, 65,80

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

110 NECCX5000:F490, F890


PCI QLogic: QLE2460-E-SP6, 18, 24, 32, 46, 64, 65, 70, QLE2462-E-SP6, 24,32, 33, 46, 64, 65, QLE2560-E-SP6, 18, 24, 62, 63, QLE2562-E-SP6, 18, 24,62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

111 NECCX5000 E:T5140,T5240


PCIExpress

Emulex: LPe11000-E-G6, 18, 50, 53, 54, 55, 56, 57, LPe11000-E6, 18, 50,53, 54, 55, 56, 57, LPe11002-E-G6, 18, 50, 53, 54, 55, 56, 57, LPe11002-E6,18, 50, 53, 54, 55, 56, 57, LPe12000-E-G6, 18, 47, 48, 49, 50, 51,LPe12000-E6, 18, 47, 48, 49, 50, 51, LPe12002-E-G6, 18, 47, 48, 49, 50, 51,LPe12002-E6, 18, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

112 NECCX5000 E:T5140,T5240


PCIExpress

Emulex: LPe11000-E-G6, 18, 50, 53, 54, 55, 56, 57, LPe11000-E6, 18, 50,53, 54, 55, 56, 57, LPe11002-E-G6, 18, 50, 53, 54, 55, 56, 57, LPe11002-E6,18, 50, 53, 54, 55, 56, 57, LPe12000-E6, 18, 47, 48, 49, 50, 51,LPe12000-E-G6, 18, 47, 48, 49, 50, 51, LPe12002-E-G6, 18, 47, 48, 49, 50,51, LPe12002-E6, 18, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

113 NECCX5000: ET100017, FT100017


PCIExpress

Emulex: LPe11000-E-G6, 50, 53, 54, 55, 56, 57, 64, 65, LPe11000-E6, 50,53, 54, 55, 56, 57, 64, 65, LPe11002-E6, 50, 53, 54, 55, 56, 57, 64, 65,LPe11002-E-G6, 50, 53, 54, 55, 56, 57, 64, 65

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

114 NECCX5000 E:T5120,T5220


PCIExpress

Emulex: LPe11000-E-G6, 50, 53, 54, 55, 56, 57, LPe11000-E6, 50, 53, 54,55, 56, 57, LPe11002-E-G6, 50, 53, 54, 55, 56, 57, LPe11002-E6, 50, 53, 54,55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

115 NECCX5000 E:T5120,T5220


PCIExpress

Emulex: LPe11000-E-G6, 50, 53, 54, 55, 56, 57, LPe11000-E6, 50, 53, 54,55, 56, 57, LPe11002-E6, 50, 53, 54, 55, 56, 57, LPe11002-E-G6, 50, 53, 54,55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

116 NECCX5000 E:T100017,T5120,T5220;

NECCX5000 FT100017


PCIExpress

Emulex: LPe12000-E-G6, 47, 48, 49, 50, 51, LPe12000-E6, 47, 48, 49, 50,51, LPe12002-E-G6, 47, 48, 49, 50, 51, LPe12002-E6, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

117 NECCX5000 E:T100017,T5120,T5220;

NECCX5000 FT100017


PCIExpress

Emulex: LPe12000-E6, 47, 48, 49, 50, 51, LPe12000-E-G6, 47, 48, 49, 50,51, LPe12002-E-G6, 47, 48, 49, 50, 51, LPe12002-E6, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

118 NECCX5000 E:T5140,T5240


PCIExpress

Oracle: SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)18,53, 55, 58, 59, 64, 65, 66, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)18, 58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4(LPe11002-S)18, 53, 55, 58, 59, 64, 65, 66,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)18, 58, 59, 64,65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

119 NECCX5000 E:T100017,T5120,T5220;

NECCX5000 FT100017


PCIExpress

Oracle: SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)53,55, 58, 59, 64, 65, 66, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N(QLE2460)58, 59, 64, 65, 67, 68, 69, SG-XPCIE2FC-EM4(LPe11002-S)53, 55, 58, 59, 64, 65, 66,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)58, 59, 64, 65,67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

Storage Array


120 NECCX5000 E:T100017,T5120,T5140,T5220,T5240;

NECCX5000 FT100017


PCIExpress

Oracle: SG-XPCIE1FC-EM8-Z/SG-XPCIE1FC-EM8-N(LPe12000-S)6, 50, 55, 58, 59,SG-XPCIE2FC-EM8-Z/SG-XPCIE2FC-EM8-N (LPe12002-S)6, 50, 55,58, 59

FC-AL,FC-SW


Y38, 43,44

121 NECCX5000 E:T100017,T5120,T5140,T5220,T5240;

NECCX5000 FT100017


PCIExpress

Oracle: SG-XPCIE1FC-QF8-Z/SG-XPCIE1FC-QF8-N (QLE2560)6, 58,59, 60, 61, SG-XPCIE2FC-QF8-Z/SG-XPCIE2FC-QF8-N (QLE2562)6,58, 59, 61

FC-AL,FC-SW


Y38, 39,45

122 NECCX5000 E:T5140,T5240


PCIExpress

QLogic: QLE2460-E-SP6, 18, 24, 32, 46, 70, QLE2462-E-SP6, 18, 24, 32,33, 46, QLE2560-E-SP6, 18, 24, 62, 63, QLE2562-E-SP6, 18, 24, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

123 NECCX5000: ET100017, FT100017


PCIExpress

QLogic: QLE2460-E-SP6, 24, 32, 46, 64, 65, 70, QLE2462-E-SP6, 24, 32,33, 46, 64, 65

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

124 NECCX5000 E:T5120,T5220


PCIExpress

QLogic: QLE2460-E-SP6, 24, 32, 46, 70, QLE2462-E-SP6, 24, 32, 33, 46 FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

125 NECCX5000 E:T100017,T5120,T5220;

NECCX5000 FT100017


PCIExpress

QLogic: QLE2560-E-SP6, 24, 62, 63, QLE2562-E-SP6, 24, 62, 63 FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

126 NECCX5000 E:M400016,M500016,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Emulex: LP10000-E6, 50, 53, 55, 66, 81, 92, 96, LP10000DC-E6, 50, 53, 55,81, 92, 96

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

127 NECCX5000 E:M400016,M500016,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Emulex: LP10000-E6, 50, 53, 55, 66, 81, 92, 96, LP10000DC-E6, 50, 53, 55,81, 92, 96, LPe12000-E-G6, 47, 48, 49, 50, 51, LPe12000-E6, 47, 48, 49, 50,51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

128 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Emulex: LP11000-E6, 50, 53, 54, 55, 56, 57, 64, 65, LP11002-E6, 50, 53, 54,55, 56, 57, 64, 65

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

129 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Emulex: LP11000-E6, 50, 53, 54, 55, 56, 57, 64, 65, LP11002-E6, 50, 53, 54,55, 56, 57, 64, 65, LPe11000-E-G6, 50, 53, 54, 55, 56, 57, LPe11000-E6, 50,53, 54, 55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

130 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

Emulex: LP9002-E (LP9002L-E)6, 66, 93, 94, 97, 98, LPe11002-E6, 50,53, 54, 55, 56, 57, LPe11002-E-G6, 50, 53, 54, 55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

Storage Array


131 NECCX5000 E:M400016,M500016


PCIExpress,PCI-X

Emulex: LP9002-E (LP9002L-E)6, 66, 93, 94, 97, 98, LPe12002-E6, 47,48, 49, 50, 51, LPe12002-E-G6, 47, 48, 49, 50, 51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

132 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

Emulex: LPe11000-E-G6, 50, 53, 54, 55, 56, 57, LPe11000-E6, 50, 53, 54,55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

133 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000 FT200017


PCIExpress,PCI-X

Emulex: LPe11000-E6, 50, 53, 54, 55, 56, 57, LPe11000-E-G6, 50, 53, 54,55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

134 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000 FT200017


PCIExpress,PCI-X


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

135 NECCX5000 E:M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

136 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

Emulex: LPe11002-E6, 50, 53, 54, 55, 56, 57, LPe11002-E-G6, 50, 53, 54,55, 56, 57

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

137 NECCX5000 E:M400016,M500016,M8000,M9000;

NECCX5000:F215, F245,F445


PCIExpress,PCI-X

Emulex: LPe12000-E-G6, 47, 48, 49, 50, 51, LPe12000-E6, 47, 48, 49, 50,51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

138 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

Emulex: LPe12000-E6, 47, 48, 49, 50, 51, LPe12000-E-G6, 47, 48, 49, 50,51

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

139 NECCX5000: ET200017, FT200017


PCIExpress,PCI-X


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

140 NECCX5000 E:M400016,M500016,M8000,M9000


PCIExpress,PCI-X


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

141 NECCX5000 E:M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

142 NECCX5000: ET200017, FT200017,F215, F245,F445


PCIExpress,PCI-X


FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

143 NECCX5000 E:M400016,M500016,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCI1FC-EM2 (LP10000)53, 55, 58, 59, 66,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)58, 59, 65, 67, 68,69, SG-XPCI2FC-EM2 (LP10000DC)53, 55, 58, 59, 66,SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)58, 59, 65, 67, 68,69, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N (QLE2460)58, 59, 64,65, 67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

Storage Array


144 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)6,50, 53, 55, 58, 59, 65, 66, SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N(LP11000-S)50, 53, 55, 58, 59, 65, 66,SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N (LP11002-S)6, 50, 53, 55,58, 59, 65, 66, SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N(LP11002-S)50, 53, 55, 58, 59, 65, 66,SG-XPCIE1FC-EM4/SG-XPCIE1FC-EM4-N (LPe11000-S)53, 55, 58,59, 64, 65, 66, SG-XPCIE2FC-EM4 (LPe11002-S)53, 55, 58, 59, 64, 65, 66,SG-XPCIE2FC-QF4/SG-XPCIE2FC-QF4-N (QLE2462)58, 59, 64, 65,67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

145 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

Oracle: SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)58, 59, 67,68, 69, SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)58, 59, 67,68, 69, SG-XPCIE1FC-QF4/SG-XPCIE1FC-QF4-N (QLE2460)58, 59,67, 68, 69

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

146 NECCX5000 E:M400016,M500016,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 58, 59, 77, 79, 99,SG-XPCI2FC-QF2-Z (X6768A)6, 58, 59, 77, 99, X6768A(SG-XPCI2FC-QF2)6, 58, 75, 76, 77

FC-AL,FC-SW


Y38, 39,45

147 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCIE1FC-EM8-Z/SG-XPCIE1FC-EM8-N(LPe12000-S)6, 50, 55, 58, 59,SG-XPCIE2FC-EM8-Z/SG-XPCIE2FC-EM8-N (LPe12002-S)6, 50, 55,58, 59

FC-AL,FC-SW


Y38, 43,44

148 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCIE1FC-QF8-Z/SG-XPCIE1FC-QF8-N (QLE2560)6, 58,59, 60, 61, SG-XPCIE2FC-QF8-Z/SG-XPCIE2FC-QF8-N (QLE2562)6,58, 59, 61

FC-AL,FC-SW


Y38, 39,45

149 NECCX5000 E:M400016,M500016,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

QLogic: QLA2340-E-SP6, 82, 83, 88, QLA2342-E-SP6, 82, 83, 85,QLA2460-E-SP6, 24, 33, 46, 64, 65, 80, QLA2462-E-SP6, 24, 33, 46, 64, 65,80

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

150 NECCX5000 E:M8000,M9000


PCIExpress,PCI-X

QLogic: QLA2460-E-SP6, 24, 33, 46, 80, QLA2462-E-SP6, 24, 33, 46, 80 FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

151 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

QLogic: QLE2460-E-SP6, 24, 32, 46, 70, QLE2462-E-SP6, 24, 32, 33, 46,QLE2560-E-SP6, 24, 62, 63, QLE2562-E-SP6, 24, 62, 63

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

152 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890


PCI Emulex: LP10000-E50, 53, 55, 64, 66, 89, 90, 91, 92, 95, 96, 101, 102, 103,105, LP10000DC-E50, 53, 55, 64, 89, 90, 91, 92, 95, 96, 101, 102, 103, 105,LP11000-E50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105,LP11002-E6, 50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105, LP9002-E(LP9002L-E)64, 66, 89, 90, 93, 94, 95, 97, 98, 101, 102, 103, 105, LP9802-E6,64, 66, 89, 90, 91, 92, 93, 94, 95, 96, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

153 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890


PCI Oracle: SG-XPCI1FC-EM2 (LP10000)53, 55, 58, 59, 66, 101, 102, 103, 105,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)6, 50, 53, 55,58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N (LP11000-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105, SG-XPCI2FC-EM2 (LP10000DC)53, 55, 58, 59,66, 101, 102, 103, 105, SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N(LP11002-S)6, 50, 53, 55, 58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N (LP11002-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

Storage Array


154 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890


PCI Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 58, 59, 77, 79, 101, 102, 103, 105,SG-XPCI2FC-QF2-Z (X6768A)6, 58, 59, 77, 79, 101, 102, 103, X6767A(SG-XPCI1FC-QF2)6, 58, 64, 75, 77, 78, 99, 101, 102, 103, 105, X6768A(SG-XPCI2FC-QF2)6, 58, 64, 75, 76, 77, 78, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,45

155 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890


PCI QLogic: QLA2340-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105,QLA2342-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105, 108,QLA2460-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105,QLA2462-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

156 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

Emulex: LP10000-E50, 53, 55, 64, 66, 89, 90, 91, 92, 95, 96, 101, 102, 103,105, LP10000DC-E50, 53, 55, 64, 89, 90, 91, 92, 95, 96, 101, 102, 103, 105,LP11000-E50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105,LP11002-E6, 50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105, LP9002-E(LP9002L-E)64, 66, 89, 90, 93, 94, 95, 97, 98, 101, 102, 103, 105, LP9802-E6,64, 66, 89, 90, 91, 92, 93, 94, 95, 96, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

157 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCI1FC-EM2 (LP10000)53, 55, 58, 59, 66, 101, 102, 103, 105,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)6, 50, 53, 55,58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N (LP11000-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105, SG-XPCI2FC-EM2 (LP10000DC)53, 55, 58, 59,66, 101, 102, 103, 105, SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N(LP11002-S)6, 50, 53, 55, 58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N (LP11002-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

158 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 58, 59, 77, 79, 101, 102, 103, 105,SG-XPCI2FC-QF2-Z (X6768A)6, 58, 59, 77, 79, 101, 102, 103, X6767A(SG-XPCI1FC-QF2)6, 58, 64, 75, 77, 78, 99, 101, 102, 103, 105, X6768A(SG-XPCI2FC-QF2)6, 58, 64, 75, 76, 77, 78, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,45

159 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

QLogic: QLA2340-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105,QLA2342-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105, 108,QLA2460-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105,QLA2462-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

160 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890

OracleSolaris 9SPARC5, 106

PCI 04/045 Emulex: LP10000-E50, 53, 55, 64, 66, 89, 90, 91, 92, 95, 96, 101, 102, 103,105, LP10000DC-E50, 53, 55, 64, 89, 90, 91, 92, 95, 96, 101, 102, 103, 105,LP11000-E50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105,LP11002-E6, 50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105, LP9002-E(LP9002L-E)64, 66, 89, 90, 93, 94, 95, 97, 98, 101, 102, 103, 105, LP9802-E6,64, 66, 89, 90, 91, 92, 93, 94, 95, 96, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

161 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890


PCI 04/045 Oracle: SG-XPCI1FC-EM2 (LP10000)53, 55, 58, 59, 66, 101, 102, 103, 105,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)6, 50, 53, 55,58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N (LP11000-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105, SG-XPCI2FC-EM2 (LP10000DC)53, 55, 58, 59,66, 101, 102, 103, 105, SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N(LP11002-S)6, 50, 53, 55, 58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N (LP11002-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

162 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890


PCI 04/045 Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 58, 59, 77, 79, 101, 102, 103, 105,SG-XPCI2FC-QF2-Z (X6768A)6, 58, 59, 77, 79, 101, 102, 103, X6767A(SG-XPCI1FC-QF2)6, 58, 64, 75, 77, 78, 99, 101, 102, 103, 105, X6768A(SG-XPCI2FC-QF2)6, 58, 64, 75, 76, 77, 78, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,45

163 NECCX5000:F20K109,F2900,F490,F4900,F6900,F890


PCI 04/045 QLogic: QLA2340-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105,QLA2342-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105, 108,QLA2460-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105,QLA2462-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

164 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

04/045 Emulex: LP10000-E50, 53, 55, 64, 66, 89, 90, 91, 92, 95, 96, 101, 102, 103,105, LP10000DC-E50, 53, 55, 64, 89, 90, 91, 92, 95, 96, 101, 102, 103, 105,LP11000-E50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105,LP11002-E6, 50, 53, 54, 55, 56, 57, 64, 65, 101, 102, 103, 104, 105, LP9002-E(LP9002L-E)64, 66, 89, 90, 93, 94, 95, 97, 98, 101, 102, 103, 105, LP9802-E6,64, 66, 89, 90, 91, 92, 93, 94, 95, 96, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45, 52

165 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

04/045 Oracle: SG-XPCI1FC-EM2 (LP10000)53, 55, 58, 59, 66, 101, 102, 103, 105,SG-XPCI1FC-EM4-Z/SG-XPCI1FC-EM4-Z-N (LP11000-S)6, 50, 53, 55,58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-EM4/SG-XPCI1FC-EM4-Z-N (LP11000-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI1FC-QF4/SG-XPCI1FC-QF4-N (QLA2460)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105, SG-XPCI2FC-EM2 (LP10000DC)53, 55, 58, 59,66, 101, 102, 103, 105, SG-XPCI2FC-EM4-Z/SG-XPCI2FC-EM4-Z-N(LP11002-S)6, 50, 53, 55, 58, 59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-EM4/SG-XPCI2FC-EM4-Z-N (LP11002-S)50, 53, 55, 58,59, 65, 66, 101, 102, 103, 104, 105,SG-XPCI2FC-QF4/SG-XPCI2FC-QF4-N (QLA2462)58, 59, 65, 67, 68,69, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,41, 42, 43,44, 45

Storage Array


166 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

04/045 Oracle: SG-XPCI1FC-QL2 (QLA2340)6, 58, 59, 77, 79, 101, 102, 103, 105,SG-XPCI2FC-QF2-Z (X6768A)6, 58, 59, 77, 79, 101, 102, 103, X6767A(SG-XPCI1FC-QF2)6, 58, 64, 75, 77, 78, 99, 101, 102, 103, 105, X6768A(SG-XPCI2FC-QF2)6, 58, 64, 75, 76, 77, 78, 101, 102, 103, 105

FC-AL,FC-SW


Y38, 39,45

167 NECCX5000:F215, F245,F445


PCIExpress,PCI-X

04/045 QLogic: QLA2340-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105,QLA2342-E-SP6, 82, 83, 84, 86, 87, 88, 101, 102, 103, 105, 108,QLA2460-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105,QLA2462-E-SP6, 24, 33, 46, 64, 65, 80, 101, 102, 103, 104, 105

FC-AL,FC-SW


Y38, 39,40, 41, 42,43, 44, 45

168 NECCX5000:F490, F890

OracleSolaris 10SPARC10, 11,12, 13, 14, 15

PCI S10Update 8(10/09)

Oracle: SG-XPCIEFCOE2-Q-SR (QLE8142 CNA)6, 18, 20, 21, 22, 24, 25,SG-XPCIEFCOE2-Q-TA (QLE8152 CNA)6, 18, 19, 20, 21, 22, 23, 24;

QLogic: QLE8140-SR-E-SP (CNA)6, 18, 20, 21, 22, 24, 25, 31,QLE8142-SR-E-SP (CNA)6, 18, 20, 21, 22, 24, 25, 31, QLE8150-CU-E-SP(CNA)6, 18, 20, 21, 22, 24, 25, 31

FCoE EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

N

169 NECCX5000 E:T100017,T5120,T5140,T5220,T5240;

NECCX5000 FT100017


PCIExpress

S10Update 8(10/09)




N

170 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

S10Update 8(10/09)




N

171 NECCX5000:F490, F890


PCI Oracle: SG-XPCIEFCOE2-Q-SR (QLE8142 CNA)6, 18, 21, 24,SG-XPCIEFCOE2-Q-TA (QLE8152 CNA)6, 18, 19, 21, 24;

QLogic: QLE8140-SR-E-SP (CNA)6, 18, 21, 24, 31, QLE8142-SR-E-SP(CNA)6, 18, 21, 24, 31, QLE8150-CU-E-SP (CNA)6, 18, 21, 24, 31


N

172 NECCX5000 E:T100017,T5120,T5140,T5220,T5240;

NECCX5000 FT100017


PCIExpress

Oracle: SG-XPCIEFCOE2-Q-SR (QLE8142 CNA)6, 18, 21, 24,SG-XPCIEFCOE2-Q-TA (QLE8152 CNA)6, 18, 19, 21, 24;



N

173 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Oracle: SG-XPCIEFCOE2-Q-SR (QLE8142 CNA)6, 18, 21, 24,SG-XPCIEFCOE2-Q-TA (QLE8152 CNA)6, 18, 19, 21, 24;



N

174 NECCX5000:F490, F890

OracleSolaris 10SPARC5, 10,11, 12, 13, 14,15


Emulex: OCe10102-FM-E (CNA)1, 2, 3, 6, 7, 9, 26, 27, 28, 29, 30,OCe10102-FX-E (CNA)1, 2, 3, 6, 7, 9, 26, 27, 28, 29, 30, OCe11102-FM-E(CNA)1, 2, 3, 4, 6, 7, 8, 9, OCe11102-FX-E (CNA)1, 2, 3, 4, 6, 7, 8, 9

FCoE,Network:IP


N

175 NECCX5000 E:T100017,T5120,T5140,T5220,T5240;

NECCX5000 FT100017


PCIExpress

S10Update 8(10/09)5


FCoE,Network:IP


N

176 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

S10Update 8(10/09)5


FCoE,Network:IP


N

Storage Array


177 NECCX5000:F490, F890


PCI Emulex: OCe10102-FM-E (CNA)1, 6, 7, 9, 26, 27, 28, 30,OCe10102-FX-E (CNA)1, 6, 7, 9, 26, 27, 28, 30, OCe11102-FM-E(CNA)1, 4, 6, 7, 8, 9, OCe11102-FX-E (CNA)1, 4, 6, 7, 8, 9

FCoE,Network:IP


N

178 NECCX5000 E:T100017,T5120,T5140,T5220,T5240;

NECCX5000 FT100017


PCIExpress

Emulex: OCe10102-FM-E (CNA)1, 6, 7, 9, 26, 27, 28, 30,OCe10102-FX-E (CNA)1, 6, 7, 9, 26, 27, 28, 30, OCe11102-FM-E(CNA)1, 4, 6, 7, 8, 9, OCe11102-FX-E (CNA)1, 4, 6, 7, 8, 9

FCoE,Network:IP


N

179 NECCX5000 E:M400016,M500016,M8000,M9000,T200017;

NECCX5000: FT200017,F215, F245,F445


PCIExpress,PCI-X

Emulex: OCe10102-FM-E (CNA)1, 6, 7, 9, 26, 27, 28, 30,OCe10102-FX-E (CNA)1, 6, 7, 9, 26, 27, 28, 30, OCe11102-FM-E(CNA)1, 4, 6, 7, 8, 9, OCe11102-FX-E (CNA)1, 4, 6, 7, 8, 9

FCoE,Network:IP


N

1. Firmware Version 4.0.360.32. Driver Version V2.60k (Solaris Patch 145953-06)3. Driver Version V2.60h (Solaris Patch 145098-04)4. BIOS 3.703.397.345. Minimum supported OS revision with the server6. SNIA HBA API Supported.7. BIOS 4.0.360.38. Firmware Version 3.703.397.349. Must add "set pcie:pcie_max_mps=0" in the /etc/system file for Symmetrix or CLARiiON attach. Do not include quotes on the entry.

10. Supports S10 Update 8 (10/09)11. For LDOM support, please refer to the 'Virtualization Server Support' table available via EMC PowerLink:

https://elabnavigator.emc.com/emcpubs/elab/esm/pdf/Virtualization_Server_Support.pdf12. The Snapshot and Clone features of ZFS are supported only through Oracle Corporation.13. Supports S10 Update 10 (8/11).14. Supports S10 Update 9 (9/10)15. EMC recommends as a best practice that customers upgrade to the most recent Solaris 10 SPARC patch bundle released on the Oracle website:http://www.sunsolve.sun.com16. Cx-based snapshot is not supported on Ibrix Fusion Snapshot feature17. Supports Logical Domain (LDOM) with MPxIO and Sun Volume Manager (SVM) on Solaris 10 11/06. PowerPath 5.1 or higher is supported on the Control domain and I/O domain.18. Fcode should be loaded on all HBA's at the time of initial installation. This should only be done before configuring devices, and should not be done after devices are configured. If

HBA does not contain Fcode and Fcode is loaded after devices are configured, the device paths will change and this could result in loss of data.19. Copper connection only. Supported with Passive and Active Twinax cables.20. Driver Version V3.05 (Solaris Patch 146489-05)21. Firmware Version 05.03.0222. Driver Version V3.00p (Solaris Patch 143957-05)23. Driver Version V3.00 (Solaris Patch 143-957-03)24. FCode Value 3.1525. Driver Version V3.00 (Solaris Patch 143957-03)26. Firmware Version 2.703.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com27. BIOS 2.703.397.3428. Firmware Version 2.103.269.281829. Driver Version V2.50p (Solaris Patch 145098-02)30. Firmware Version 2.702.200.17 Available in the EMC-approved section of the Emulex website.http://www.emulex.com31. FCode Value 3.0932. FCode Value 2.00 (Flash image 1.69)33. FCode Value 1.24 (Flash image 1.56) Fcode should be loaded on all HBA's at the time of initial installation. This should only be done before configuring devices, and should not be

done after devices are configured. If HBA does not contain Fcode and Fcode is loaded after devices are configured, the device paths will change and this could result in loss of data.34. Supports S10 Update 7 (05/09)35. Supports S10 Update 5 (05/08)36. Supports S10 Update 6 (10/08)37. Supports S10 Update 4 (08/07).38. For FC-AL hub connection not supported for boot device.39. The minimum firmware requirement for boot support is 2.10a10.40. Support for CX700, CX500, CX300, CX600, CX400, FC4500, FC4700, and FC5300. (FC5300 requires copper to Fibre transceiver.)41. QCP2202F-E-SP/QLA234x-E-SP requires fcode v2.00.06. Fcode should be loaded on all HBA's at the time of installation.42. Requires at least Rev 03 of LP8000-N1 HBA (part # 118031355-03)43. Boot from SAN support is maximium of 10 servers per EMC array port.44. Note: Boot with DS-8B/DS-16B switches using 2.2.1a or 2.3 switch firmware requires HBA fcode v1.12a1 or higher.45. FCode 1.17 is the minimum necessary for boot from SAN.46. FCode Value 2.04 (Flash image 1.79)47. Firmware Version 2.00a348. Firmware Version 1.10a549. Firmware Version 1.11a550. FCode Value 3.10a351. FCode Value 3.01a1 Fcode V3.01a1 is minimum requirement for boot from SAN with LPe12000/2 Emulex HBAs.52. See the EMC price book for HBA vendor ordering information. This HBA is not sold by EMC.53. FCode Value 3.00a254. Firmware Version 2.80a455. FCode Value 3.01a156. Firmware Version 2.82a457. Firmware Version 2.82a358. Support firmware revision that comes along with Solaris Leadville driver. The driver automatically updates the firmware on Sun-branded cards to the correct supported version.59. This adapter has another name without the "X" in front of "PCI", such as SG-PCI....60. FCode Value 2.0361. FCode Value 2.0462. FCode Value FCode 2.04 (Flash image 2.12)63. FCode Value Fcode 2.00 (Flash image 2.01)64. Must add "set ssd:ssd_max_throttle=20" in /etc/system for CLARiiON or Symmetrix attach.

Must add "forceload: drv/ssd" in the /etc/system when these HBA's are installed for Clariion or Symmetrix attach with PowerPath. (do not include the quotes on either entry).Driver version SAN 4.3 or older is not supported for MPxIO on EMC storage arrays.

65. Symmetrix-only attached hosts with Sun Leadville driver used with Powerpath 4.5.0 or greater and Solutions Enabler, the following is required (as per the workaround outlined inemc108113):# powermt unmanage class=hphsx# powermt save# reboot

66. FCode Value 1.50a967. FCode Value 2.01 (Solaris Patch 123305-04)68. FCode Value 1.24 (Solaris Patch 123305-02)69. FCode Value 1.17 FCode 1.17 is the minimum necessary for boot from SAN.70. FCode Value 1.24. (Flash image 1.56)71. Supports S10 Update 1 (01/06)72. Supports S10 Update 2 (06/06)73. If setting the boot disk from SAN with Solaris 10, its Target/LUN must be defined in the /kernel/drv/sd.conf file.74. Supports S10 Update 3 (11/06)75. FCode Value 1.1676. FCode Value 1.1777. FCode Value 1.14.15

Storage Array


78. Symmetrix-only attached hosts with Sun Leadville driver (X6767A and X6868A) used with Powerpath 4.3.1 or greater and Solutions Enabler, the following is required (as per theworkaround outlined in emc108113):# powermt unmanage class=hphsx# powermt save# reboot

79. FCode Value 1.14.0980. FCode Value 2.00 (Flash image 1.69) Fcode should be loaded on all HBA's at the time of initial installation. This should only be done before configuring devices, and should not be

done after devices are configured. If HBA does not contain Fcode and Fcode is loaded after devices are configured, the device paths will change and this could result in loss of data.81. For Solaris 10 versions prior to S10-U1, there are 2 packages SUNWemlxs and SUNWemlxu that are required before installing required patch 120222-04. These packages are

available on the Sun website:http://www.sun.com/download/products.xml?id=42c4317d

82. FCode Value 1.14.15 Fcode should be loaded on all HBA's at the time of initial installation. This should only be done before configuring devices, and should not be done after devicesare configured. If HBA does not contain Fcode and Fcode is loaded after devices are configured, the device paths will change and this could result in loss of data.

83. FCode Value 2.00.09 Fcode should be loaded on all HBA's at the time of initial installation. This should only be done before configuring devices, and should not be done after devicesare configured. If HBA does not contain Fcode and Fcode is loaded after devices are configured, the device paths will change and this could result in loss of data.

84. Driver Version 4.15.0385. FCode Value 2.00.0686. Driver Version 4.2287. Driver Version 4.1788. FCode Value 2.00.06 Fcode should be loaded on all HBA's at the time of initial installation. This should only be done before configuring devices, and should not be done after devices

are configured. If HBA does not contain Fcode and Fcode is loaded after devices are configured, the device paths will change and this could result in loss of data.89. Driver Version 6.11cx390. Driver Version 6.11cx291. Firmware Version 1.91a192. Firmware Version 1.92a193. FCode Value 1.50a494. FCode Value 1.50a895. Driver Version 6.10gx196. Firmware Version 1.91a597. Firmware Version 3.93a098. BIOS 2.01a2 Available in the EMC-approved section of the Emulex website.http://www.emulex.com99. FCode Value 1.14.11

100. EMC recommends as a best practice that customers upgrade to the most recent Solaris 11 SPARC SRU released on the Oracle website:http://support.oracle.com101. Driver Version SAN 4.4.15102. Driver Version SAN 4.4.14103. Driver Version SAN 4.4.13104. SDS support on Solaris 8 requires minimum SDS version 4.2.1 with patch 108693-16 or later version.105. For servers running Solaris 8 or 9 with the Sun SAN driver, the following applies:

Must add "set fcp:ssfcp_enable_auto_configuration=1" (do not include quote marks) in /etc/system to fix the following problems:1. VxVM - rootdg can not be imported during boot2. SVM - Volume Manager can not be started after system boot3. PowerPath 4.x - error message "All paths to (array type) (array name) vol(volume number) are dead"

106. EMC recommends as a best practice that customers upgrade to the most recent Solaris 9 SPARC patch bundle released on the Oracle website:http://www.sunsolve.sun.com107. Driver Version V3.05 Minimum requires version.108. FCode Value 1.14.13 Fcode should be loaded on all HBA's at the time of initial installation. This should only be done before configuring devices, and should not be done after devices

are configured. If HBA does not contain Fcode and Fcode is loaded after devices are configured, the device paths will change and this could result in loss of data.109. Use of the LP9002DC or QLA2342 requires FCO A0218-1 from Sun for HBA's to operate in 66mhz mode. Without this FCO the HBA's will only come up in 33mhz mode which could

have an impact on performance.

VMware ESXVMwareHewlett Packard

Hewlett Packard

No. Host SystemOperating

System Host Bus Host Bus Adapter Topology Storage ArrayExternal

Boot

1 Hewlett PackardProliant BL685c(dual coreprocessor)1

VMware ESX 4.1(vSphere 4)2, 3, 4,5, 6, 7, 8, 9

PCIExpress

Hewlett Packard: Emulex LPe1105-HP 4Gb FC HBA for HPc-Class Bladesystem (403621-B21)10, 11, 12, 13, QLogicQMH2462 4Gb FC HBA for HP c-Class Bladesystem(403619-B21)11, 27, 28, QLogic QMH2572 8Gb FC HBA forHP c-Class Bladesystem (651281-B21)11, 26

FC-SW EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300 (File/iSCSI)

Y14, 15

2 Hewlett PackardProliant BL685c(dual coreprocessor)1

VMware ESX 4.1(vSphere 4)2, 3, 4,5, 6, 7, 8, 9

PCIExpress

Hewlett Packard HP NC551m Dual Port FlexFabric 10GbConverged Network Adapter (580151-B21)16, 17, 18, 19, 20, 22,23, 24, 25

FCoE21 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300 (File/iSCSI)

Y14, 15

1. Please see the HP website for supported BL c-Class model numbers.The supported model numbers are available in the quickspecs documents available for each BL c-Class blade.

2. EMC supports VMware's recommendations for number of nodes in native ESX cluster configurations.3. Oracle Database 11g R1 is supported on VMware vSphere 4.0 Virtual Machines with Symmetrix, CLARiiON, and Celerra storage platforms. For details, refer to

http://www.vmware.com/solutions/partners/alliances/oracle.html.4. Supports 2-node Microsoft Cluster Services (MSCS) with Windows 2003 and Windows 2008 virtual machines in CIB (Cluster in Box) and CAB (Cluster across Boxes) configurations.

VMware NMP (Native Multipathing) and PowerPath/VE are supported with MSCS.The following SCSI Controllers are supported with VMWare and MSCS:Windows 2000 Server LSI Logic Parallel, Windows Server 2003 LSI Logic Parallel, Windows Server 2008 LSI Logic Parallel.You must download the LSI Logic Parallel driver for Windows 2000 Server on the LSI Web site.

5. For information on VMware VAAI (VMware vStorage APIs for Array Integration) support with EMC storage, and details on array firmware versions that support VAAI please refer tothe Storage/SAN section of the VMware Hardware Compatibility Guide athttp://www.vmware.com/resources/compatibility/search.php.

6. For a list of supported guest operating systems, refer tohttp://www.vmware.com/resources/compatibility/search.php?deviceCategory=software. For additional information refer to theGuest Operating System Installation Guide at http://www.vmware.com/pdf/GuestOS_guide.pdf

7. Oracle RAC 11g R2 is supported on Red Hat RHEL 5 and Microsoft Windows Virtual Machines running on VMware vSphere 4.1 with EMC storage platforms. For details, refer tohttp://vmware.com/support/policies/oracle-support.html

8. Supported with vMotion.9. All released updates to ESX version are supported unless otherwise specified by a footnote. Please contact server vendor for the update level required for a specific server.

10. BIOS 3.11a5 Available in the EMC-approved section of the Emulex website.http://www.emulex.com11. Driver Version In-box driver This driver is included in the VMware ESX kernel. Driver upgrades not supported.12. Firmware Version 2.80a4 Available in the EMC-approved section of the Emulex website.http://www.emulex.com13. Firmware Version 2.82a4 Available in the EMC-approved section of the Emulex website.http://www.emulex.com14. Virtual machines running on VMWare ESX are supported booting from the array.15. VMWare ESX Server itself is supported booting from external array.16. BIOS v4.0.360.15 Available in the EMC-approved section of the Emulex website.http://www.emulex.com17. Firmware Version v4.0.360.15 Available in the EMC-approved section of the Emulex website.http://www.emulex.com18. Driver Version 2.102.518.0 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools Ethernet Driver19. Driver Version 8.2.0.79.25 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools Fibre Channel Driver20. BIOS 2.702.517.70321. FCoE support only with ESX 4.0. No iSCSI support22. Firmware Version 2.702.517.70323. Driver Version 8.2.1.78.22 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools Fibre Channel Driver24. BIOS 2.104.28.1.0 Available in the EMC-approved section of the Emulex website.http://www.emulex.com25. Firmware Version 2.104.28.1.0 Available in the EMC-approved section of the Emulex website.http://www.emulex.com26. SNIA HBA API Supported.27. BIOS 2.15 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com28. BIOS 2.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com

Hitachi

Storage Array


Hitachi

No. Host System Operating SystemHostBus Host Bus Adapter Topology Storage Array

ExternalBoot

1 Hitachi HA8000/RS440 AL VMware ESX 4.1(vSphere 4)3, 4, 5, 6, 7,8, 9, 10, 11, 12

PCI Hitachi: GQ-CC7811/7812-EX(LPe1250-F8)13, 14, 15, 16,GQ-CC7821/7822-EX (LPe12002-M8)13, 14,15, 16

FC-AL,FC-SW

EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300 (File/iSCSI)

Y1, 2

2 Hitachi: HA8000/RS210 AL,HA8000/RS220 AL,HA8000/TS20 AL

VMware ESX 4.1(vSphere 4)3, 4, 5, 6, 7,8, 9, 10, 12

PCI Hitachi: GQ-CC7811/7812-EX(LPe1250-F8)13, 14, 15, 16,GQ-CC7821/7822-EX (LPe12002-M8)13, 14,15, 16

FC-AL,FC-SW


Y1, 2

1. Virtual machines running on VMWare ESX are supported booting from the array.2. VMWare ESX Server itself is supported booting from external array.3. EMC supports VMware's recommendations for number of nodes in native ESX cluster configurations.4. Oracle Database 11g R1 is supported on VMware vSphere 4.0 Virtual Machines with Symmetrix, CLARiiON, and Celerra storage platforms. For details, refer to






9. Supported with vMotion.10. All released updates to ESX version are supported unless otherwise specified by a footnote. Please contact server vendor for the update level required for a specific server.11. Supported only from VMware ESX4.1 U1 or later12. Supported from VMware ESX4.1 or later13. SNIA HBA API Supported.14. Firmware Version 1.10a5 Available in the EMC-approved section of the Emulex website.http://www.emulex.com15. Driver Version In-box driver This driver is included in the VMware ESX kernel. Driver upgrades not supported.16. BIOS 2.02a2 Available in the EMC-approved section of the Emulex website.http://www.emulex.com

ISCSI to FC RoutingConfiguration Notes

Microsoft Windows 2003 [x64]Microsoft

Microsoft

No.Operating

System Host Bus Adapter DriverNetwork

Configuration BridgeFirmwareRevision

ExternalBoot Storage Array Comments

1 MicrosoftWindows 2003[x64] EnterpriseEdition: R2 SP2,SP2;

MicrosoftWindows 2003[x64] StandardEdition: R2 SP2,SP2;

MicrosoftWindows 2003[x64] StorageServerEnterpriseEdition: R2 SP2,SP2;

MicrosoftWindows 2003[x64] StorageServer StandardEdition: R2 SP2,SP2

Generic Vendor NIC:10/1001, 9, 13, 14, GbE1, 9,13, 14

MicrosoftiSCSI Initiator2.03, MicrosoftiSCSI Initiator2.046, 16, 17, 18

LAN Only12 Cisco MDS 9216A,Cisco MDS 9513

NX-OS4.2.(7b),NX-OS5.0.(1a),NX-OS 5.2.1,SAN-OS3.3.(5a)

N EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See10, 11,15







LAN Only12 Cisco MDS 9216i SAN-OS is3.2.(1a),SAN-OS is3.3.(1c),SAN-OS is3.3.(2)


See10, 11,15

Storage Array








LAN Only12 Cisco MDS 9222i NX-OS4.2.(7b),NX-OS 5.0(1a),NX-OS 5.2.1,NX-OS 5.2.2,SAN-OS3.3.(5a)


See10, 11,15







LAN Only12 Cisco MDS 9506 NX-OS4.2.(7b),NX-OS5.1.(1a),NX-OS 5.2.1,NX-OS 5.2.2,SAN-OS3.3.(5a)


See10, 11,15









See10, 11,15







LAN Only12 McDATA (Nishan)IPS 330020, 21, 26,McDATA (Nishan)IPS 430020, 21, 26

EOSi 4.5 N EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See10, 11,15





LAN Only12, 23 EMC ConnectrixMP 162024, EMCConnectrix MP264012, 20, 21, 22,McDATA Eclipse264019, 20, 21, 22


See10, 11,15

Storage Array










LAN Only12, 23 McDATA Eclipse162020, 21, 24, 25,26

EOSi 4.7.0 N EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See10, 11,15





QLogic: QLA4050-E-SP1, 2,3, 4, 5, 6, 7, 8, 9,QLA4050C-E-SP1, 2, 3, 4, 5,6, 7, 8, 9, QLA4052C-E-SP1,2, 3, 4, 5, 6, 7, 8, 9

2.1.3.26,2.1.3.28



Y EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See10, 11






2.1.3.26,2.1.3.28



See10, 11




Microsoft


2.1.3.26,2.1.3.28



See10, 11

Storage Array


Windows 2003[x64] StorageServer StandardEdition: R2 SP2,SP2






2.1.3.26,2.1.3.28



See10, 11






2.1.3.26,2.1.3.28



See10, 11






2.1.3.26,2.1.3.28



See10, 11






2.1.3.26,2.1.3.28



See10, 11

Storage Array







2.1.3.26,2.1.3.28



See10, 11

17 MicrosoftWindows 2003[x64] StorageServerEnterpriseEdition: R2 SP2,SP2;


QLogic: QLA4010-E-SP1, 2,3, 5, 6, 9, QLA4010C-E-SP1,2, 3, 5, 6, 9

2.1.3.26,2.1.3.28




See10, 11




2.1.3.26,2.1.3.28



See10, 11




2.1.3.26,2.1.3.28



See10, 11




2.1.3.26,2.1.3.28



See10, 11




2.1.3.26,2.1.3.28



See10, 11




2.1.3.26,2.1.3.28



See10, 11

Storage Array





2.1.3.26,2.1.3.28



See10, 11




2.1.3.26,2.1.3.28



See10, 11

1. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.2. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com3. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.4. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator.5. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.6. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)7. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)8. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.9. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.

10. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.11. Microsoft Dynamic Disks are not supported.12. Routed networks (layer 3) require iSCSI digest to be enabled.13. The following NICs are not supported: 3COM-3C996B14. Any Microsoft supported server/NIC for the listed operating system revision is supported.15. EMC provides documentation for iSCSI configurations that contains helpful information for using iSCSI with EMC storage. Visit EMC Powerlink and download part number

300-000-603 for the Windows Host Connectivity Guide.16. EMC recommends that on hosts with multiple NICs that the Software Initiator Source_IP default selection not be used, and a NIC be explicitly selected for maximum path availability.

Refer to the EMC Host Connectivity Guide for more detailed information.17. NIC teaming with Microsoft iSCSI Initiator is not supported.18. Microsoft iSCSI Initiator software.19. max number of initiator logged into the iSCSI target port is 1220. Multivendor switches (any combination of Brocade, McDATA and Cisco switches) within a single SAN island are not supported.21. There can only be one Eclipse or IPS switch in each SAN island.22. max number of zones in the fabric (SAN Island) where the Eclipse/IPS switch connected to is 102423. Copper GE SFPs are supprted in GE ports only if they are approved by Mcdata24. Use of Copper Fast Ethernet RJ45 ports on MP1620 is not supported. The iFCP and iSCSI solutions must use the GigE SFP ports (Optics SFP and Copper SFP supplied by

Brocade)25. Equivalent to EMC Connectrix MP-1620M26. max number of zones in the fabric (SAN Island) where the Eclipse/IPS switch connected to is 512


Microsoft

No.Operating

System Host Bus Adapter DriverNetwork

Configuration BridgeFirmwareRevision

ExternalBoot Storage Array Comments

1 MicrosoftWindows 2003[x86]DataCenter: R2SP2, SP2;

MicrosoftWindows 2003[x86] EnterpriseEdition: R2 SP2,SP2;

MicrosoftWindows 2003[x86] StandardEdition: R2 SP2,SP2

Generic Vendor NIC:10/100, GbE

Microsoft iSCSIInitiator 2.03,Microsoft iSCSIInitiator 2.04,Microsoft iSCSIInitiator 2.05,Microsoft iSCSIInitiator 2.06

LAN Only Brocade 4800019,20, 21, 22

5.2.1a, 5.2.2,5.3.0a, 6.0.0b,6.0.0c






Microsoft iSCSIInitiator 2.03,Microsoft iSCSIInitiator 2.045, 6,7, 8

LAN Only4 Cisco MDS9216A, CiscoMDS 9513



See1, 2, 3

Storage Array









See1, 2, 3






LAN Only4 Cisco MDS 9222i NX-OS4.2.(7b),NX-OS5.0(1a),NX-OS 5.2.1,NX-OS 5.2.2,SAN-OS3.3.(5a)


See1, 2, 3








See1, 2, 3








See1, 2, 3








See1, 2, 3








See1, 2, 3







See1, 2, 3

Storage Array






IBM QLogic iSCSI ExpCard for BladeCenter(26K6487)9, 12, 13

2.1.1.5, 2.1.3.26 LAN Only4 Cisco MDS9216A, CiscoMDS 9513



See2, 3





2.1.1.5, 2.1.3.26 LAN Only4 Cisco MDS 9216i SAN-OS is3.2.(1a),SAN-OS is3.3.(1c),SAN-OS is3.3.(2)


See2, 3





2.1.1.5, 2.1.3.26 LAN Only4 Cisco MDS 9222i NX-OS4.2.(7b),NX-OS5.0(1a),NX-OS 5.2.1,NX-OS 5.2.2,SAN-OS3.3.(5a)


See2, 3





2.1.1.5, 2.1.3.26 LAN Only4 Cisco MDS 9506 NX-OS4.2.(7b),NX-OS5.1.(1a),NX-OS 5.2.1,NX-OS 5.2.2,SAN-OS3.3.(5a)


See2, 3







See2, 3





2.1.1.5, 2.1.3.26 LAN Only4 McDATA (Nishan)IPS 330024, 25, 29,McDATA (Nishan)IPS 430024, 25, 29


See2, 3

Storage Array






2.1.1.5, 2.1.3.26 LAN Only4, 23 EMC ConnectrixMP 162027, EMCConnectrix MP26404, 24, 25, 26,McDATA Eclipse264024, 25, 26, 28


See2, 3





2.1.1.5, 2.1.3.26 LAN Only4, 23 McDATA Eclipse162024, 25, 27, 29,30


See2, 3




QLogic: QLA4050-E-SP8, 9,12, 13, 14, 15, 16, 17, 18,QLA4050C-E-SP8, 9, 12, 13,14, 15, 16, 17, 18,QLA4052C-E-SP8, 9, 12, 13,14, 15, 16, 17, 18

2.1.3.26, 2.1.3.28 LAN Only4 Cisco MDS9216A, CiscoMDS 9513



See2, 3





2.1.3.26, 2.1.3.28 LAN Only4 Cisco MDS 9216i SAN-OS is3.2.(1a),SAN-OS is3.3.(1c),SAN-OS is3.3.(2)


See2, 3





2.1.3.26, 2.1.3.28 LAN Only4 Cisco MDS 9222i NX-OS4.2.(7b),NX-OS5.0(1a),NX-OS 5.2.1,NX-OS 5.2.2,SAN-OS3.3.(5a)


See2, 3







See2, 3






See2, 3

Storage Array







2.1.3.26, 2.1.3.28 LAN Only4 McDATA (Nishan)IPS 330024, 25, 29,McDATA (Nishan)IPS 430024, 25, 29


See2, 3





2.1.3.26, 2.1.3.28 LAN Only4, 23 EMC ConnectrixMP 162027, EMCConnectrix MP26404, 24, 25, 26,McDATA Eclipse264024, 25, 26, 28


See2, 3





2.1.3.26, 2.1.3.28 LAN Only4, 23 McDATA Eclipse162024, 25, 27, 29,30


See2, 3

1. EMC provides documentation for iSCSI configurations that contains helpful information for using iSCSI with EMC storage. Visit EMC Powerlink and download part number300-000-603 for the Windows Host Connectivity Guide.

2. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.3. Microsoft Dynamic Disks are not supported.4. Routed networks (layer 3) require iSCSI digest to be enabled.5. EMC recommends that on hosts with multiple NICs that the Software Initiator Source_IP default selection not be used, and a NIC be explicitly selected for maximum path availability.

Refer to the EMC Host Connectivity Guide for more detailed information.6. NIC teaming with Microsoft iSCSI Initiator is not supported.7. Microsoft iSCSI Initiator software.8. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)9. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.

10. The following NICs are not supported: 3COM-3C996B11. Any Microsoft supported server/NIC for the listed operating system revision is supported.12. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.13. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.14. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com15. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.16. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator.17. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)18. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.19. The blade for distance extension is PB-48K-18i20. The 10G FC10-6(Xenon) blade is supported for ISL connectivity from Xenon to Xenon only.21. The 16-port 8Gbit blade (FC8-16) and the 32-port 8Gbit blade (FC8-32) are supported in the Brocade 48000 or EMC Connectrix ED-48000B chassis running supported FOS v6.0.0c

and up.22. requires PB-48K-16IP blade.23. Copper GE SFPs are supprted in GE ports only if they are approved by Mcdata24. Multivendor switches (any combination of Brocade, McDATA and Cisco switches) within a single SAN island are not supported.25. There can only be one Eclipse or IPS switch in each SAN island.26. max number of zones in the fabric (SAN Island) where the Eclipse/IPS switch connected to is 102427. Use of Copper Fast Ethernet RJ45 ports on MP1620 is not supported. The iFCP and iSCSI solutions must use the GigE SFP ports (Optics SFP and Copper SFP supplied by

Brocade)28. max number of initiator logged into the iSCSI target port is 1229. max number of zones in the fabric (SAN Island) where the Eclipse/IPS switch connected to is 51230. Equivalent to EMC Connectrix MP-1620M

Internet Protocol Addressing SupportConfiguration Notes

No. Item Type Item Name IP Addressing1 Storage Array EMC Unified Storage: VNXe3100 (File/iSCSI), VNXe3300 (File/iSCSI) IPv4

Storage Array


2 Storage Array EMC Unified Storage: VNXe3100 (File/iSCSI), VNXe3300 (File/iSCSI) IPv6

Native iSCSIConfiguration Notes

Apple MAC OSXApple

Apple

No. Operating System Host Bus AdapterNetwork

Configuration Storage ArrayStorage Operative

EnvironmentExternal

Boot

1 Apple MAC OSX: 10.5.5, 10.5.6,10.5.7, 10.5.8

Generic Vendor NICGbE1, 2

LAN Only EMC Unified Storage VNXe3300(File/iSCSI)

1.1 N

1. Driver Version ATTO XtendSAN Software Initiator 3.212. Driver Version ATTO XtendSAN Software Initiator 3.22

Asianux AX [32-Bit]Asianux

Asianux

No.Operating

System Host Bus AdapterNetwork

Configuration Storage ArrayExternal

Boot Comments

1 Asianux AX[32-Bit] 4.0SP12, 3

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)14, 15, 16, 17

LAN Only7 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300 (File/iSCSI)

Y5, 6 See4


QLogic QLA4010-E-SP16, 20, 21, 22, 23, QLogic QLA4010C-E-SP16, 20, 21,22, 23, QLogic QLA4050-E-SP16, 17, 18, 19, 20, 21, QLogicQLA4050C-E-SP16, 17, 18, 19, 20, 21, QLogic QLA4052C-E-SP16, 17, 18, 19,20, 21, QLogic QLE4060C-E-SP14, 16, 17, 18, 21, 24, QLogicQLE4062C-E-SP14, 16, 17, 18, 21, 24


Y5 See4


QLogic QLE8240-SR-E-SP33, 34, 35, QLogic QLE8242-SR-E-SP33, 34, 35,QLogic QLE8250-CU-E-SP33, 34, 35, QLogic QLE8252-CU-E-SP33, 34, 35

LAN Only7 EMC Unified StorageVNXe3300 (File/iSCSI)

N

4 Asianux AX[32-Bit] 4.03, 31



Y5, 6 See4

5 Asianux AX[32-Bit] 4.03, 31



Y5 See4

6 Asianux AX[32-Bit]: 4.0SP12, 3, 4.03, 31

Generic Vendor NIC 10/1001, Generic Vendor NIC GbE1, 8, 9, 10 LAN Only7 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300 (File/iSCSI)

Y5, 6 See4

7 Asianux AX[32-Bit]: 4.0SP12, 3, 4.03, 31

Generic Vendor NIC 10GbE1, 8, 10, 13 LAN Only7 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300 (File/iSCSI)

Y5, 6, 11,12

See4

8 Asianux AX[32-Bit]: 4.0SP12, 3, 4.03, 31

IBM IBM Broadcom 10GbE 2-Port Ethernet Expansion Card for IBMBladeCenter (46M6168)10, 26, 27, 28, 29, 30, IBM IBM Broadcom 10GbE4-Port Ethernet Expansion Card for IBM BladeCenter (46M6164)10, 26, 27,28, 29, 30


Y6 See4, 25

1. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linuxdistributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.

2. Supported kernels: 2.6.32-131.12.1.el6. Confirm kernel support with server vendor.3. Asianux includes separate releases from Redflag DC Server, Miracle Linux and HanCom Linux Server. Each individual distribution is released asynchronous of the other. Please

review the individual distributors release to ensure the availabilty of that desired release.4. Please refer to the Host Bus Adapter note for the supported NICs.5. Broadcom iSCSI boot is supported with following adapters:

- Broadcom 57710 based cards- Broadcom 57711 based cards- Broadcom 5708- Broadcom 5709Please visit http://support.dell.com for the currently supported servers; as well as, BIOS/firmware versions.

6. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168iSCSI boot is supported with Red Hat RHEL 5.5Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.

7. Routed networks (layer 3) require iSCSI digest to be enabled.8. Broadcom iSCSI offload (without iboot) is supported with following adapters:


9. Broadcom iSCSI boot is supported on Linux with following adapters:- Broadcom 5710 based cards- Broadcom 5711 based cardsPlease visit http://support.dell.com for the currently supported servers; as well as, BIOS/firmware versions.

10. NIC teaming with the Linux software initiator is not supported.11. Intel iSCSI boot is supported on Oracle servers with the following Intel Adapters: . X1106A-Z (10 GbE 1-port SR Oplin/ Belle Fountaine), X1107A-Z (10 GbE 2-port SR Oplin/ Green

Fountaine), X1108A-Z (10 GbE dual-port EM Longwater). X5561A-ZSFP + SR Transceiver; required for X1108A-Z) iSCSI. Please visithttp://www.intel.com for the most currentlysupported firmware/driver revisions.

12. Intel iSCSI boot is supported with the following Intel adapters:- Ethernet X520 10GbE Dual Port KX4- Ethernet X520-2 10GbEPlease visit http://support.dell.com for most currently supported servers and firmare/BIOS versions.

13. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.14. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com15. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com16. Driver Version 5.02.00-k5 Driver is integrated into the kernel.17. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com18. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com19. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com20. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.21. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com22. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com23. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com

Storage Array


24. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.25. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.26. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.27. Firmware Version 2.1.1a28. BIOS 5.0.1129. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php30. Broadcom iSCSI offload (without iboot) is supported with following adapters:

- Broadcom 57710 based cards- Broadcom 57711 based cardsPlease visit http://www.IBM.com for the currently supported servers; as well as, BIOS/firmware versions.

31. Supported kernels: 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6. Confirm kernel support with server vendor.32. Driver Version 5.01.00.01.05.04-k9 Driver is integrated into the kernel.33. Driver Version 5.02.11.00.05.06-c3 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com34. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com35. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com

Asianux AX [x86_64]Asianux

Asianux

No.Operating



Boot Comments

1 Asianux AX[x86_64] 4.0SP14, 5



Y1, 14 See2

2 Asianux AX[x86_64] 4.0SP14, 5



Y14 See2

3 Asianux AX[x86_64] 4.0SP14, 5

QLogic QLE8240-SR-E-SP33, 34, 35, QLogic QLE8242-SR-E-SP33, 34, 35,QLogic QLE8250-CU-E-SP33, 34, 35, QLogic QLE8252-CU-E-SP33, 34, 35

LAN Only12 EMC Unified StorageVNXe3300 (File/iSCSI)

N

4 Asianux AX[x86_64] 4.05, 13



Y1, 14 See2

5 Asianux AX[x86_64] 4.05, 13



Y14 See2

6 Asianux AX[x86_64]: 4.0SP14, 5, 4.05, 13

Generic Vendor NIC 10/10015, Generic Vendor NIC GbE8, 15, 16, 17 LAN Only12 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300 (File/iSCSI)

Y1, 14 See2

7 Asianux AX[x86_64]: 4.0SP14, 5, 4.05, 13

Generic Vendor NIC 10GbE8, 15, 16, 20 LAN Only12 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300 (File/iSCSI)

Y1, 14,18, 19

See2

8 Asianux AX[x86_64]: 4.0SP14, 5, 4.05, 13

IBM IBM Broadcom 10GbE 2-Port Ethernet Expansion Card for IBMBladeCenter (46M6168)6, 7, 8, 9, 10, 11, IBM IBM Broadcom 10GbE 4-PortEthernet Expansion Card for IBM BladeCenter (46M6164)6, 7, 8, 9, 10, 11


Y1 See2, 3


2. Please refer to the Host Bus Adapter note for the supported NICs.3. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.4. Supported kernels: 2.6.32-131.12.1.el6. Confirm kernel support with server vendor.5. Asianux includes separate releases from Redflag DC Server, Miracle Linux and HanCom Linux Server. Each individual distribution is released asynchronous of the other. Please

review the individual distributors release to ensure the availabilty of that desired release.6. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php7. Broadcom iSCSI offload (without iboot) is supported with following adapters:


8. NIC teaming with the Linux software initiator is not supported.9. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.10. Firmware Version 2.1.1a11. BIOS 5.0.1112. Routed networks (layer 3) require iSCSI digest to be enabled.13. Supported kernels: 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6. Confirm kernel support with server vendor.14. Broadcom iSCSI boot is supported with following adapters:



16. Broadcom iSCSI offload (without iboot) is supported with following adapters:- Broadcom 57710 based cards- Broadcom 57711 based cards- Broadcom 5708- Broadcom 5709Please visit http://support.dell.com for the currently supported servers; as well as, BIOS/firmware versions.


18. Intel iSCSI boot is supported on Oracle servers with the following Intel Adapters: . X1106A-Z (10 GbE 1-port SR Oplin/ Belle Fountaine), X1107A-Z (10 GbE 2-port SR Oplin/ GreenFountaine), X1108A-Z (10 GbE dual-port EM Longwater). X5561A-ZSFP + SR Transceiver; required for X1108A-Z) iSCSI. Please visithttp://www.intel.com for the most currentlysupported firmware/driver revisions.


20. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.21. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com22. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com23. Driver Version 5.02.00-k5 Driver is integrated into the kernel.24. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com

Storage Array


25. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com26. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com27. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.28. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com29. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com30. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com31. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.32. Driver Version 5.01.00.01.05.04-k9 Driver is integrated into the kernel.33. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com34. Driver Version 5.02.11.00.05.06-c3 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com35. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com

Citrix Systems, Inc. XenServerCitrix Systems, Inc.

Citrix Systems, Inc.



EnvironmentExternal

Boot

1 Citrix Systems, Inc.XenServer 5.0

Generic Vendor NICGbE3, 4

LAN Only1, 2 EMC Unified Storage VNXe3300(File/iSCSI)

1.1 N

1. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.2. Routed networks (layer 3) require iSCSI digest to be enabled.3. Driver Version included in OS4. Refer to XenServer host system requirements in the XenServer Installation Guide.

Hewlett Packard HP-UXHewlett Packard

Hewlett Packard



EnvironmentExternal

Boot

1 Hewlett Packard HP-UX 11i: v1.0 (HP-UX11.11), v2 (HP-UX 11.23), v3 (HP-UX11.31)

Generic Vendor NIC 10/1001, 4,Generic Vendor NIC GbE1, 4

LAN Only2, 3 EMC Unified StorageVNXe3300 (File/iSCSI)

1.1 N

2 Hewlett Packard HP-UX 11i: v1.0 (HP-UX11.11)9, 10, 11, v2 (HP-UX 11.23)

Generic Vendor NIC 10/1008,Generic Vendor NIC GbE8

LAN Only EMC Unified StorageVNXe3300 (File/iSCSI)6, 7

N

3 Hewlett Packard HP-UX 11i: v2 (HP-UX11.23), v3 (HP-UX 11.31)

Generic Vendor NIC 10GbE5 LAN Only EMC Unified StorageVNXe3300 (File/iSCSI)6, 7

N

1. Driver Version included in OS2. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.3. Routed networks (layer 3) require iSCSI digest to be enabled.4. The following NICs are not supported: 3COM-3C996B5. Driver Version native6. Failover only supported with PVlinks and LVM7. VxVM and/or DMP not supported at this time8. Driver Version N/A9. Refer to the "iSCSI Server Setup Guide for HP-UX" for configuration details.

10. Requires HP's iSCSI Software initiator version 11.11.03e11. HP-UX 11i 64 bit only

IBM AIXIBM

IBM

No.Operating



EnvironmentExternal

Boot Comments

1 IBM AIX: 5.3,6.1

Generic Vendor NIC 10/1001,10, Generic Vendor NIC GbE1

LAN Only2, 3 EMC Unified Storage VNXe3300:(File), (File/iSCSI)

1.1 N

2 IBM AIX: 5.311,6.14

Generic Vendor NIC 10/1009,Generic Vendor NIC GbE9

LAN Only EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300 (File/iSCSI)

N See5, 6, 7, 8

1. Driver Version included in OS2. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.3. Routed networks (layer 3) require iSCSI digest to be enabled.4. Requires minimum AIX 6100-02-01-0847 for support5. TOE (TCP Offload Engine) adapters are currently not supported6. EMC PowerPath is not supported.7. Veritas Storage Foundation for AIX is not supported8. Native MPIO is not supported9. Driver Version Native AIX Driver

10. The following NICs are not supported: 3COM-3C996B11. Requires minimum AIX 5300-09-01-0847 for support


Microsoft

No.Operating


Configuration Storage Array

StorageOperative

EnvironmentExternal

Boot Comments

1 Microsoft Windows2003 [x64]Enterprise Edition:R2 SP2, SP2;

Microsoft Windows2003 [x64]Standard Edition:R2 SP2, SP2

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA forHP c-Class BladeSystem (488074-B21)4, 5, 6

LAN Only7 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y8, 9, 10, 11,12, 13, 14,15, 16

See1, 2, 3

Storage Array



Microsoft Windows2003 [x64]Standard Edition:R2 SP2, SP2;

Microsoft Windows2003 [x64] StorageServer EnterpriseEdition: R2 SP2,SP2;

Microsoft Windows2003 [x64] StorageServer StandardEdition: R2 SP2,SP2

Generic Vendor NIC 10/10020, 21, 23, 24, 28, 29, GenericVendor NIC GbE20, 21, 23, 24, 27

LAN Only7 EMC UnifiedStorage VNXe3300(File/iSCSI)

1.1 N See3





Generic Vendor NIC 10GbE20, 24, 26, 49, 50, 51, GenericVendor NIC GbE19, 20, 21, 22, 23, 24, IBM IBM Broadcom10GbE 2-Port Ethernet Expansion Card for IBMBladeCenter (46M6168)13, 41, 42, 43, 44, 45, 46, IBM IBMBroadcom 10GbE 4-Port Ethernet Expansion Card forIBM BladeCenter (46M6164)13, 41, 42, 43, 44, 45, 46, 47, 48


Y8, 9, 10, 11,12, 13, 14,15, 16

See1, 2, 3, 17,18





Generic Vendor NIC GbE20, 21, 22, 23, 24, 25, 26 LAN Only7 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y8, 9, 10, 11,12, 13, 14,15, 16

See1, 2, 3, 17





IBM QLogic iSCSI Exp Card for BladeCenter(26K6487)24, 31, 33, 35, 36, 40, QLogic QLA4050-E-SP20,24, 30, 31, 33, 34, 35, 36, 37, 38, 39, QLogicQLA4050C-E-SP20, 24, 30, 31, 33, 34, 35, 36, 37, 38, 39,QLogic QLA4052C-E-SP20, 24, 30, 31, 33, 34, 35, 36, 37, 38,39

LAN Only7, 32 EMC UnifiedStorage VNXe3300(File/iSCSI)

1.1 N See3

6 Microsoft Windows2003 [x64] StorageServer EnterpriseEdition: R2 SP2,SP2;


QLogic QLA4010-E-SP20, 24, 30, 31, 33, 34, 36, 37, QLogicQLA4010C-E-SP20, 24, 30, 31, 33, 34, 36, 37


1.1 N See3

1. Powerpath iSCSI 1.1 is supported with Windows 2003 operating systems.2. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.3. Microsoft Dynamic Disks are not supported.4. BIOS 1.145. Driver Version 2.1.4.19 Requires Microsoft STORPort hotfix Q957910. Please seehttp://support.microsoft.com/kb/957910. NOTE: Hotfix Q957910 requires a minimum of Service

Pack 2 (SP2) to be installed before the hotfix can be installed.To obtain this hotfix, fill out the hotfix request form at http://support.microsoft.com/hotfix/KBHotfix.aspx?kbnum=957910&kbln=en-us

6. Firmware Version 3.00.01.497. Routed networks (layer 3) require iSCSI digest to be enabled.8. Intel iSCSI boot is supported on Dell servers with the following adapters: PRO/1000 PF, PRO/1000 PT, PRO/1000 PT dual port, PRO/ 1000 VT quad port, Ethernet X520 10GbE Dual

Port KX4 and Ethernet Server Adapter X520-2 10GbE Please visithttp://support.dell.com for the most currently supported servers and firmware/driver revisions.9. Broadcom iSCSI Boot is supported with the following adapters: Brocade 57712 (2xKR) bNDC, 57800s(2xSFP+/2x1GbT) rNDC, 57810s (2xSFP+) bNDC, 57810s(2xKR) Mezz, 57810

(2xSFP+) NIC.iSCSI boot is supported with Windows 2008 and Windows 2008 R2. Please visithttp://support.dell.com for the currently supported blade and rack servers, firmware/driver versionsand special install instructions.

10. iSCSI Boot from SAN is supported on certain IBM Servers BladeCenter models. Contact IBM support to obtain a list of supported blades and MicrosoftInitiator version

11. Broadcom iSCSI Boot is supported with the following adapters: Broadcom 5708, 5709, 5722, 57710 and 57711iSCSI boot is supported with Windows 2003 , Windows 2008 and Windows 2008 R2Please visit http://support.dell.com for the currently supported servers, firmware/driver versions and special install instructions.

Storage Array


12. Servers booting from external storage with QLA4010 iSCSI boards require Microsoft iSCSI Initiator 2.0 or 2.02 service to be installed. Note that HBA IQN must be altered prior toWindows installation. Refer to EMC Host Connectivity Guide for information on changing IQN and setting up boot for servers requiring MS iSCSI Initiator service.

13. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168iSCSI boot is supported with Windows 2003 , Windows 2008 and Windows 2008 R2Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.

14. iSCSI Boot from SAN is supported on Fujitsu Siemens Computers Primergy RX300 S3 servers. Contact Fujitsu Siemens Computers support to obtain a list of supported MicrosoftInitiator version and Broadcom boot BIOS versions. iSCSI Boot is supported in Microsoft Clustering Service.

15. Intel iSCSI boot is supported on Fujitsu Technology Solutions servers with the following Intel Adapters: 82575, 82576 iSCSI supported with W2008 and W2008 R2. Please visithttp://www.ts.fujitsu.com for the most currently supported servers and firmware/driver revisions.

16. Intel iSCSI boot is supported on Oracle servers with the following Intel Adapters: . X1106A-Z (10 GbE 1-port SR Oplin/ Belle Fountaine), X1107A-Z (10 GbE 2-port SR Oplin/ GreenFountaine), X1108A-Z (10 GbE dual-port EM Longwater). X5561A-ZSFP + SR Transceiver; required for X1108A-Z) iSCSI supported with W2008 and W2008 R2. Please visithttp://www.intel.com for the most currently supported firmware/driver revisions.


18. Powerpath iSCSI 1.1 is not supported with Windows 2000 operating systems.19. Driver Version Microsoft iSCSI Initiator 2.06 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported with

Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)20. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.21. The following NICs are not supported: 3COM-3C996B22. iSCSI offload is currently supported on Dell PowerEdge Servers with the Broadcom NetXtreme II Network adapters (based on the Broadcom 5708 and 5709 ASIC) To download the

latest firmware/driver, please visit http://support.dell.com23. Any Microsoft supported server/NIC for the listed operating system revision is supported.24. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.25. Driver Version Microsoft iSCSI Initiator 2.07 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported with

Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)26. Driver Version Microsoft iSCSI Initiator 2.08 MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI

Initiator software. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS) Dynamic disks are only supported on Windows 2008when using the Microsoft iSCSI Initiator. They are not supported on Windows 2003

27. Driver Version Microsoft iSCSI Initiator 2.06 EMC recommends that on hosts with multiple NICs that the Software Initiator Source_IP default selection not be used, and a NIC beexplicitly selected for maximum path availability. Refer to the EMC Host Connectivity Guide for more detailed information. NIC teaming with Microsoft iSCSI Initiator is not supported.Microsoft iSCSI Initiator software.



30. Driver Version 2.1.3.2831. Driver Version 2.1.3.2632. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.33. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com34. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.35. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software


Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.37. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)38. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)39. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.40. Driver Version 2.1.1.541. Virtual machines running on VMWare ESX are supported booting from the array.42. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php43. VMWare ESX Server itself is supported booting from external array.44. BIOS 5.0.1145. Driver Version 5.0.2C On BroadCom's 5.0.4.1 CD46. Firmware Version 2.1.1a47. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.48. The lastest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php49. Driver Version 8.10.3.0 Minimum supported driver version for Cisco UCS mezzanine adapter.50. EMC Celerra supported for Cisco UCS attach.51. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.


Microsoft

No.Operating



StorageOperative

EnvironmentExternal

Boot Comments

1 Microsoft Windows2003 [x86]DataCenter: R2SP2, SP2;

Microsoft Windows2003 [x86]Enterprise Edition:R2 SP2, SP2;


Generic Vendor NIC 10/10019, 20, 22, 23, 26, 27, GenericVendor NIC GbE19, 20, 22, 23, 25


1.1 N See3




Generic Vendor NIC 10GbE19, 23, 42, 53, 54, 55, GenericVendor NIC GbE19, 20, 21, 22, 23, 24, IBM IBM Broadcom10GbE 2-Port Ethernet Expansion Card for IBMBladeCenter (46M6168)10, 45, 46, 47, 48, 49, 50, IBM IBMBroadcom 10GbE 4-Port Ethernet Expansion Card forIBM BladeCenter (46M6164)10, 45, 46, 47, 48, 49, 50, 51, 52


Y5, 6, 7, 8, 9,10, 11, 12, 13

See1, 2, 3, 17,18




Generic Vendor NIC GbE19, 20, 21, 22, 23, 42, 43 LAN Only4 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y5, 6, 7, 8, 9,10, 11, 12, 13

See1, 2, 3, 17

Storage Array





IBM QLogic iSCSI Exp Card for BladeCenter(26K6487)19, 23, 28, 29, 30, 31, 32, 33, 34, 35, 36


Y5, 6, 7, 8, 9,10, 11, 12, 13

See1, 2, 3




IBM QLogic iSCSI Exp Card for BladeCenter(26K6487)23, 29, 30, 32, 37, 44, QLogic QLA4050-E-SP19,23, 29, 30, 31, 32, 36, 37, 38, 39, 40, QLogicQLA4050C-E-SP19, 23, 29, 30, 31, 32, 36, 37, 38, 39, 40,QLogic QLA4052C-E-SP19, 23, 29, 30, 31, 32, 36, 37, 38, 39,40


1.1 Y6, 9, 40 See3





Y5, 6, 7, 8, 9,10, 11, 12, 13

See1, 2, 3

1. Powerpath iSCSI 1.1 is supported with Windows 2003 operating systems.2. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.3. Microsoft Dynamic Disks are not supported.4. Routed networks (layer 3) require iSCSI digest to be enabled.5. Intel iSCSI boot is supported on Dell servers with the following adapters: PRO/1000 PF, PRO/1000 PT, PRO/1000 PT dual port, PRO/ 1000 VT quad port, Ethernet X520 10GbE Dual










14. BIOS 1.1415. Driver Version 2.1.4.19 Requires Microsoft STORPort hotfix Q957910. Please seehttp://support.microsoft.com/kb/957910. NOTE: Hotfix Q957910 requires a minimum of Service


16. Firmware Version 3.00.01.4917. EMC provides documentation for iSCSI configurations that contains helpful information for using iSCSI with EMC storage. Visit EMC Powerlink and download part number

300-000-603 for the Windows Host Connectivity Guide.18. Powerpath iSCSI 1.1 is not supported with Windows 2000 operating systems.19. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.20. The following NICs are not supported: 3COM-3C996B21. iSCSI offload is currently supported on Dell PowerEdge Servers with the Broadcom NetXtreme II Network adapters (based on the Broadcom 5708 and 5709 ASIC) To download the

latest firmware/driver, please visit http://support.dell.com22. Any Microsoft supported server/NIC for the listed operating system revision is supported.23. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.24. Driver Version Microsoft iSCSI Initiator 2.06 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported with

Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)25. Driver Version Microsoft iSCSI Initiator 2.06 EMC recommends that on hosts with multiple NICs that the Software Initiator Source_IP default selection not be used, and a NIC be

explicitly selected for maximum path availability. Refer to the EMC Host Connectivity Guide for more detailed information. NIC teaming with Microsoft iSCSI Initiator is not supported.Microsoft iSCSI Initiator software.



28. This iSCSI Exp Card DOES NOT support on the IBM blade server types HS21(7995,8853)29. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software


Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.31. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)32. Driver Version 2.1.3.2633. Driver Version 2.1.3.2234. BIOS 1.09a35. Firmware Version 2.00.00.4536. Driver Version 2.1.3.2837. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com38. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.39. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)40. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.41. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.42. Driver Version Microsoft iSCSI Initiator 2.08 MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI


43. Driver Version Microsoft iSCSI Initiator 2.07 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported withMicrosoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)

44. Driver Version 2.1.1.545. Driver Version 5.0.2C On BroadCom's 5.0.4.1 CD46. Virtual machines running on VMWare ESX are supported booting from the array.47. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php48. VMWare ESX Server itself is supported booting from external array.49. BIOS 5.0.11

Storage Array


50. Firmware Version 2.1.1a51. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.52. The lastest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php53. Driver Version 8.10.3.0 Minimum supported driver version for Cisco UCS mezzanine adapter.54. EMC Celerra supported for Cisco UCS attach.55. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.

Microsoft Windows 2008 R2 SP1 [IA64]Microsoft

Microsoft



Boot Comments

1 Microsoft Windows2008 R2 SP1 [IA64] forItanium-BasedSystems

Generic Vendor NIC 10GbE15, 16, 17, 18, 19, 20, Generic VendorNIC GbE15, 17, 20, 22, 23, 24, 43, Generic Vendor NIC GbE17, 20, 22,23, 24, 45

LAN Only14 EMC Unified StorageVNXe3100(File/iSCSI)

Y5, 6, 7, 8, 9,10, 11, 12, 13

See1, 2, 3, 4


Generic Vendor NIC 10GbE15, 16, 17, 18, 19, 20, Generic VendorNIC GbE15, 17, 20, 22, 23, 24, 43, Generic Vendor NIC GbE17, 20, 22,23, 24, 49


Y5, 6, 7, 8, 9,10, 11, 12, 13

See1, 2, 3, 4


Generic Vendor NIC 10GbE15, 17, 18, 19, 20, 44, Generic VendorNIC GbE17, 20, 21, 22, 23, 24, IBM IBM Broadcom 10GbE 2-PortEthernet Expansion Card for IBM BladeCenter (46M6168)10, 26, 27,28, 29, 30, 31, IBM IBM Broadcom 10GbE 4-Port EthernetExpansion Card for IBM BladeCenter (46M6164)10, 26, 27, 28, 29,30, 31, 41, 42

LAN Only14 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y5, 6, 7, 8, 9,10, 11, 12, 13

See1, 2, 3, 4,25


Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HPc-Class BladeSystem (488074-B21)46, 47, 48, IBM QLogic iSCSIExp Card for BladeCenter (26K6487)17, 20, 32, 33, 34, 35, 36, 37, 38,39, 40


Y5, 6, 7, 8, 9,10, 11, 12, 13

See2, 3, 4


2. Powerpath iSCSI 1.1 is supported with Windows 2003 operating systems.3. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.4. Microsoft Dynamic Disks are not supported.5. Intel iSCSI boot is supported on Dell servers with the following adapters: PRO/1000 PF, PRO/1000 PT, PRO/1000 PT dual port, PRO/ 1000 VT quad port, Ethernet X520 10GbE Dual










14. Routed networks (layer 3) require iSCSI digest to be enabled.15. Driver Version Microsoft iSCSI Initiator 2.08 MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI


16. Driver Version 1.0.48.1 Minimum supported driver version for Cisco UCS mezzanine adapter.17. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.18. EMC Celerra supported for Cisco UCS attach.19. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.20. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.21. Driver Version Microsoft iSCSI Initiator 2.06 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported with

Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)22. The following NICs are not supported: 3COM-3C996B23. iSCSI offload is currently supported on Dell PowerEdge Servers with the Broadcom NetXtreme II Network adapters (based on the Broadcom 5708 and 5709 ASIC) To download the

latest firmware/driver, please visit http://support.dell.com24. Any Microsoft supported server/NIC for the listed operating system revision is supported.25. Powerpath iSCSI 1.1 is not supported with Windows 2000 operating systems.26. BIOS 5.0.1127. Driver Version 5.0.2C On BroadCom's 5.0.4.1 CD28. Firmware Version 2.1.1a29. Virtual machines running on VMWare ESX are supported booting from the array.30. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php31. VMWare ESX Server itself is supported booting from external array.32. Driver Version 2.1.3.2633. Driver Version 2.1.3.2834. Firmware Version 2.00.00.4535. BIOS 1.09a36. Driver Version 2.1.3.2237. This iSCSI Exp Card DOES NOT support on the IBM blade server types HS21(7995,8853)38. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software


Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.40. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)41. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.42. The lastest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php43. Driver Version Microsoft iSCSI Initiator 2.07 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported with

Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)44. Driver Version 8.10.3.0 Minimum supported driver version for Cisco UCS mezzanine adapter.45. Driver Version Microsoft iSCSI Initiator NIC teaming with Microsoft iSCSI Initiator is not supported. Native to Windows 2008 Server installation.46. BIOS 1.1447. Driver Version 2.1.4.19 Requires Microsoft STORPort hotfix Q957910. Please seehttp://support.microsoft.com/kb/957910. NOTE: Hotfix Q957910 requires a minimum of Service


48. Firmware Version 3.00.01.4949. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported.

Storage Array


Microsoft Windows 2008 R2 SP1 [x64]Microsoft

Microsoft



Boot Comments

1 Microsoft Windows2008 R2 SP1 [x64]Standard Edition

Generic Vendor NIC GbE4, 5, 6, 7, 8, 26 LAN Only18 EMC UnifiedStorage VNXe3300(File/iSCSI)3

Y9, 10, 11,12, 13, 14,15, 16, 17

See19, 20, 21,22

2 Microsoft Windows2008 R2 SP1 [x64]:DataCenter, EnterpriseEdition, StandardEdition, StorageServer

Generic Vendor NIC 10GbE2, 4, 8, 34, 35, 36, Generic Vendor NICGbE1, 2, 4, 5, 6, 7, 8

LAN Only18 EMC UnifiedStorage: VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)3

Y9, 10, 11,12, 13, 14,15, 16, 17

See19, 20, 21,22


Generic Vendor NIC 10GbE2, 4, 8, 35, 36, 39, Generic Vendor NICGbE4, 5, 6, 7, 8, 43, IBM IBM Broadcom 10GbE 2-Port EthernetExpansion Card for IBM BladeCenter (46M6168)14, 28, 29, 30, 31, 32, 33,IBM IBM Broadcom 10GbE 4-Port Ethernet Expansion Card for IBMBladeCenter (46M6164)14, 28, 29, 30, 31, 32, 33, 37, 38, QLogicQLE8240-SR-E-SP24, 25, QLogic QLE8242-SR-E-SP24, 25, QLogicQLE8250-CU-E-SP24, 25, QLogic QLE8252-CU-E-SP24, 25


Y9, 10, 11,12, 13, 14,15, 16, 17

See19, 20, 21,22, 23


Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)40, 41, 42, IBM QLogic iSCSI Exp Card forBladeCenter (26K6487)4, 8, 44, 45, 46, 47, 48, 49, 50, 51, 52


Y9, 10, 11,12, 13, 14,15, 16, 17

See20, 21, 22

5 Microsoft Windows2008 R2 SP1 [x64]:DataCenter, EnterpriseEdition, StorageServer


Y9, 10, 11,12, 13, 14,15, 16, 17

See19, 20, 21,22

6 Microsoft Windows2008 R2 SP1 [x64]:DataCenter, StandardEdition

Generic Vendor NIC GbE4, 5, 6, 7, 8, 27 LAN Only18 EMC UnifiedStorage VNXe3100(File/iSCSI)

Y9, 10, 11,12, 13, 14,15, 16, 17

See19, 20, 21,22

7 Microsoft Windows2008 R2 SP1 [x64]:Enterprise Edition,Storage Server


Y9, 10, 11,12, 13, 14,15, 16, 17

See19, 20, 21,22

1. Driver Version Microsoft iSCSI Initiator 2.07 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported withMicrosoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)

2. Driver Version Microsoft iSCSI Initiator 2.08 MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSIInitiator software. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS) Dynamic disks are only supported on Windows 2008when using the Microsoft iSCSI Initiator. They are not supported on Windows 2003

3. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" QuorumConfiguration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."

4. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.5. The following NICs are not supported: 3COM-3C996B6. iSCSI offload is currently supported on Dell PowerEdge Servers with the Broadcom NetXtreme II Network adapters (based on the Broadcom 5708 and 5709 ASIC) To download the

latest firmware/driver, please visit http://support.dell.com7. Any Microsoft supported server/NIC for the listed operating system revision is supported.8. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.9. Broadcom iSCSI Boot is supported with the following adapters: Brocade 57712 (2xKR) bNDC, 57800s(2xSFP+/2x1GbT) rNDC, 57810s (2xSFP+) bNDC, 57810s(2xKR) Mezz, 57810



11. Intel iSCSI boot is supported on Dell servers with the following adapters: PRO/1000 PF, PRO/1000 PT, PRO/1000 PT dual port, PRO/ 1000 VT quad port, Intel Ethernet X520 10GbEDual Port KX4, Intel X520 Dual Port 10Gb KR NDC, and Ethernet Server Adapter X520-2 10GbE. Please visithttp://support.dell.com for the most currently supported blade and rackservers, firmware/driver revisions and special install instructions.







18. Routed networks (layer 3) require iSCSI digest to be enabled.19. EMC provides documentation for iSCSI configurations that contains helpful information for using iSCSI with EMC storage. Visit EMC Powerlink and download part number

300-000-603 for the Windows Host Connectivity Guide.20. Powerpath iSCSI 1.1 is supported with Windows 2003 operating systems.21. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.22. Microsoft Dynamic Disks are not supported.23. Powerpath iSCSI 1.1 is not supported with Windows 2000 operating systems.24. BIOS 3.0625. Driver Version 2.1.5.2526. Driver Version Microsoft iSCSI Initiator NIC teaming with Microsoft iSCSI Initiator is not supported. Native to Windows 2008 Server installation.27. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported.28. Firmware Version 2.1.1a29. BIOS 5.0.1130. Driver Version 5.0.2C On BroadCom's 5.0.4.1 CD31. Virtual machines running on VMWare ESX are supported booting from the array.32. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php33. VMWare ESX Server itself is supported booting from external array.34. Driver Version 1.0.48.1 Minimum supported driver version for Cisco UCS mezzanine adapter.35. EMC Celerra supported for Cisco UCS attach.36. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.37. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.38. The lastest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php39. Driver Version 8.10.3.0 Minimum supported driver version for Cisco UCS mezzanine adapter.40. BIOS 1.1441. Driver Version 2.1.4.19 Requires Microsoft STORPort hotfix Q957910. Please seehttp://support.microsoft.com/kb/957910. NOTE: Hotfix Q957910 requires a minimum of Service


42. Firmware Version 3.00.01.4943. Driver Version Microsoft iSCSI Initiator 2.06 NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software. PowerPath 5.0.0 is not supported with

Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)

Storage Array


44. This iSCSI Exp Card DOES NOT support on the IBM blade server types HS21(7995,8853)45. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software


Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.47. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)48. Driver Version 2.1.3.2849. Driver Version 2.1.3.2250. BIOS 1.09a51. Driver Version 2.1.3.2652. Firmware Version 2.00.00.45

Microsoft Windows 2008 R2 [x64]Microsoft

Microsoft



StorageOperative

EnvironmentExternal

Boot Comments

1 Microsoft Windows2008 R2 [x64]Standard Edition

Generic Vendor NIC GbE24, 25, 26, 27, 28 LAN Only16 EMC UnifiedStorage VNXe3300(File/iSCSI)

1.1 N See20

2 Microsoft Windows2008 R2 [x64]:DataCenter,Enterprise Edition


1.1 N See20

3 Microsoft Windows2008 R2 [x64]:DataCenter,Enterprise Edition


Y5, 8, 9, 10,11, 12, 13,14, 15

See17, 18,19, 20

4 Microsoft Windows2008 R2 [x64]:DataCenter,Enterprise Edition,Standard Edition,Storage Server

Generic Vendor NIC 10GbE25, 28, 32, 33, 34, 35, GenericVendor NIC GbE25, 26, 27, 28, 36, 37, IBM IBM Broadcom10GbE 2-Port Ethernet Expansion Card for IBMBladeCenter (46M6168)1, 2, 3, 4, 5, 6, 7, IBM IBMBroadcom 10GbE 4-Port Ethernet Expansion Card forIBM BladeCenter (46M6164)1, 2, 3, 4, 5, 6, 7, 22, 23, QLogicQLE8240-SR-E-SP30, 31, QLogic QLE8242-SR-E-SP30,31, QLogic QLE8250-CU-E-SP30, 31, QLogicQLE8252-CU-E-SP30, 31


Y5, 8, 9, 10,11, 12, 13,14, 15

See17, 18,19, 20


Generic Vendor NIC 10GbE25, 28, 32, 33, 34, 35, IBM IBMBroadcom 10GbE 2-Port Ethernet Expansion Card forIBM BladeCenter (46M6168)1, 2, 3, 4, 5, 6, 7, IBM IBMBroadcom 10GbE 4-Port Ethernet Expansion Card forIBM BladeCenter (46M6164)1, 2, 3, 4, 5, 6, 7, 22, 23, QLogicQLE8240-SR-E-SP30, 31, QLogic QLE8242-SR-E-SP30,31, QLogic QLE8250-CU-E-SP30, 31, QLogicQLE8252-CU-E-SP30, 31

LAN Only16 EMC UnifiedStorage VNXe3300(File/iSCSI)21

Y5, 8, 9, 10,11, 12, 13,14, 15

See17, 18,19, 20



LAN Only16 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)21

Y5, 8, 9, 10,11, 12, 13,14, 15

See18, 19, 20

7 Microsoft Windows2008 R2 [x64]:Standard Edition,Storage Server


Y5, 8, 9, 10,11, 12, 13,14, 15

See17, 18,19, 20

1. BIOS 5.0.112. Driver Version 5.0.2C On BroadCom's 5.0.4.1 CD3. Firmware Version 2.1.1a4. Virtual machines running on VMWare ESX are supported booting from the array.5. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

iSCSI boot is supported with Windows 2003 , Windows 2008 and Windows 2008 R2Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.

6. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php7. VMWare ESX Server itself is supported booting from external array.8. Broadcom iSCSI Boot is supported with the following adapters: Brocade 57712 (2xKR) bNDC, 57800s(2xSFP+/2x1GbT) rNDC, 57810s (2xSFP+) bNDC, 57810s(2xKR) Mezz, 57810










300-000-603 for the Windows Host Connectivity Guide.18. Powerpath iSCSI 1.1 is supported with Windows 2003 operating systems.19. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.20. Microsoft Dynamic Disks are not supported.21. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" Quorum

Configuration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."22. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.23. The lastest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php24. Driver Version Microsoft iSCSI Initiator NIC teaming with Microsoft iSCSI Initiator is not supported. Native to Windows 2008 Server installation. Microsoft iSCSI Initiator software.25. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.26. The following NICs are not supported: 3COM-3C996B27. Any Microsoft supported server/NIC for the listed operating system revision is supported.28. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.29. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software.30. Driver Version 2.1.5.2531. BIOS 3.0632. EMC Celerra supported for Cisco UCS attach.33. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.

Storage Array


34. Driver Version Microsoft iSCSI Initiator 2.08 MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSIInitiator software. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS) Dynamic disks are only supported on Windows 2008when using the Microsoft iSCSI Initiator. They are not supported on Windows 2003

35. Driver Version 1.0.48.1 Minimum supported driver version for Cisco UCS mezzanine adapter.36. iSCSI offload is currently supported on Dell PowerEdge Servers with the Broadcom NetXtreme II Network adapters (based on the Broadcom 5708 and 5709 ASIC) To download the

latest firmware/driver, please visit http://support.dell.com37. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported.38. Driver Version 2.1.4.1939. BIOS 1.1440. Firmware Version 3.00.01.4941. Driver Version Microsoft iSCSI Initiator NIC teaming with Microsoft iSCSI Initiator is not supported. Native to Windows 2008 Server installation.


Microsoft



StorageOperative

EnvironmentExternal

Boot Comments

1 Microsoft Windows 2008 [x64]Enterprise: Edition SP216,Edition16;

Microsoft Windows 2008 [x64]Standard Edition16


1.1 N See14

2 Microsoft Windows 2008 [x64]Enterprise: Edition SP216,Edition16;

Microsoft Windows 2008 [x64]Standard: Edition SP216,Edition16;

Microsoft Windows 2008 [x64]Storage: Server, Server SP2

Hewlett Packard Qlogic QMH4062 1GbEiSCSI HBA for HP c-Class BladeSystem(488074-B21)28, 29, 30


Y1, 2, 3, 4,5, 6, 7, 8, 9

See12, 13, 14

3 Microsoft Windows 2008 [x64]:DataCenter SP216,DataCenter16, EnterpriseEdition SP216, EnterpriseEdition16, Standard EditionSP216, Standard Edition16,Storage Server, StorageServer SP2

Generic Vendor NIC 10GbE31, 35, 38, 39, 40,41, IBM IBM Broadcom 10GbE 2-PortEthernet Expansion Card for IBMBladeCenter (46M6168)6, 15, 17, 18, 19, 20, 21,IBM IBM Broadcom 10GbE 4-Port EthernetExpansion Card for IBM BladeCenter(46M6164)6, 15, 17, 18, 19, 20, 21, 23, 24


Y1, 2, 3, 4,5, 6, 7, 8, 9

See11, 12, 13,14

4 Microsoft Windows 2008 [x64]:DataCenter SP216,DataCenter16, EnterpriseEdition SP216, EnterpriseEdition16, Standard EditionSP216, Standard Edition16,Storage Server, StorageServer SP2, Web Server

QLogic QLE8240-SR-E-SP25, 27, QLogicQLE8242-SR-E-SP25, 27, QLogicQLE8250-CU-E-SP25, 27, QLogicQLE8252-CU-E-SP25, 27


Y1, 2, 3, 4,5, 6, 7, 8, 9

See11, 12, 13,14, 26

5 Microsoft Windows 2008 [x64]:DataCenter SP216,DataCenter16, StandardEdition SP216


1.1 N See14

6 Microsoft Windows 2008 [x64]:DataCenter SP216, EnterpriseEdition SP216, EnterpriseEdition16, Standard EditionSP216, Standard Edition16,Storage Server SP2


Y1, 2, 3, 4,5, 6, 7, 8, 9

See11, 12, 13,14

7 Microsoft Windows 2008 [x64]:DataCenter SP216, EnterpriseEdition16, Storage Server


Y1, 2, 3, 4,5, 6, 7, 8, 9

See11, 12, 13,14

8 Microsoft Windows 2008 [x64]:DataCenter16, EnterpriseEdition SP216, StandardEdition SP216, StandardEdition16, Storage Server SP2


Y1, 2, 3, 4,5, 6, 7, 8, 9

See11, 12, 13,14

9 Microsoft Windows 2008 [x64]:DataCenter16, Storage Server


Y1, 2, 3, 4,5, 6, 7, 8, 9

See11, 12, 13,14

1. Broadcom iSCSI Boot is supported with the following adapters: Brocade 57712 (2xKR) bNDC, 57800s(2xSFP+/2x1GbT) rNDC, 57810s (2xSFP+) bNDC, 57810s(2xKR) Mezz, 57810(2xSFP+) NIC.iSCSI boot is supported with Windows 2008 and Windows 2008 R2. Please visithttp://support.dell.com for the currently supported blade and rack servers, firmware/driver versionsand special install instructions.










300-000-603 for the Windows Host Connectivity Guide.12. Powerpath iSCSI 1.1 is supported with Windows 2003 operating systems.13. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.14. Microsoft Dynamic Disks are not supported.15. Firmware Version 2.1.1a16. Windows Server Core installation option is supported by EMC. Contact your server vendor to determine their support statement for Server Core.17. Virtual machines running on VMWare ESX are supported booting from the array.18. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php19. VMWare ESX Server itself is supported booting from external array.

Storage Array


20. BIOS 5.0.1121. Driver Version 5.0.2C On BroadCom's 5.0.4.1 CD22. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" Quorum

Configuration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."23. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.24. The lastest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php25. Driver Version 2.1.5.2526. Powerpath iSCSI 1.1 is not supported with Windows 2000 operating systems.27. BIOS 3.0628. BIOS 1.1429. Driver Version 2.1.4.1930. Firmware Version 3.00.01.4931. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.32. The following NICs are not supported: 3COM-3C996B33. iSCSI offload is currently supported on Dell PowerEdge Servers with the Broadcom NetXtreme II Network adapters (based on the Broadcom 5708 and 5709 ASIC) To download the

latest firmware/driver, please visit http://support.dell.com34. Any Microsoft supported server/NIC for the listed operating system revision is supported.35. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.36. Driver Version Microsoft iSCSI Initiator NIC teaming with Microsoft iSCSI Initiator is not supported. Native to Windows 2008 Server installation.37. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported.38. EMC Celerra supported for Cisco UCS attach.39. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.40. Driver Version Microsoft iSCSI Initiator 2.08 MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI


41. Driver Version 1.0.48.1 Minimum supported driver version for Cisco UCS mezzanine adapter.42. Driver Version Microsoft iSCSI Initiator NIC teaming with Microsoft iSCSI Initiator is not supported. Native to Windows 2008 Server installation. Microsoft iSCSI Initiator software.43. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software.


Microsoft



StorageOperative

EnvironmentExternal

Boot Comments

1 Microsoft Windows 2008[x86] Enterprise: EditionSP26, Edition6;

Microsoft Windows 2008[x86] Standard: EditionSP26, Edition6

Hewlett Packard Qlogic QMH4062 1GbE iSCSIHBA for HP c-Class BladeSystem(488074-B21)24, 25, 26


Y11, 12, 13,14, 15, 16,17, 18, 19

See8, 9, 10

2 Microsoft Windows 2008[x86]: DataCenter SP26,DataCenter6, EnterpriseEdition SP26, EnterpriseEdition6, Standard EditionSP26, Standard Edition6

Generic Vendor NIC 10GbE1, 5, 39, 40, 41, 42,Generic Vendor NIC GbE1, 2, 3, 4, 5, 21, IBM IBMBroadcom 10GbE 2-Port Ethernet ExpansionCard for IBM BladeCenter (46M6168)16, 28, 29, 30,31, 32, 33, IBM IBM Broadcom 10GbE 4-PortEthernet Expansion Card for IBM BladeCenter(46M6164)16, 28, 29, 30, 31, 32, 33, 37, 38


Y11, 12, 13,14, 15, 16,17, 18, 19

See7, 8, 9, 10


Generic Vendor NIC 10GbE1, 5, 39, 40, 41, 42, IBMIBM Broadcom 10GbE 2-Port Ethernet ExpansionCard for IBM BladeCenter (46M6168)16, 28, 29, 30,31, 32, 33, IBM IBM Broadcom 10GbE 4-PortEthernet Expansion Card for IBM BladeCenter(46M6164)16, 28, 29, 30, 31, 32, 33, 37, 38

LAN Only20 EMC UnifiedStorage VNXe3300(File/iSCSI)22

Y11, 12, 13,14, 15, 16,17, 18, 19

See7, 8, 9, 10



1.1 N See10

5 Microsoft Windows 2008[x86]: DataCenter SP26,DataCenter6, EnterpriseEdition SP26, EnterpriseEdition6, Standard EditionSP26, Standard Edition6,Web Server

QLogic QLE8240-SR-E-SP35, 36, QLogicQLE8242-SR-E-SP35, 36, QLogicQLE8250-CU-E-SP35, 36, QLogicQLE8252-CU-E-SP35, 36


Y11, 12, 13,14, 15, 16,17, 18, 19

See7, 8, 9,10, 34

6 Microsoft Windows 2008[x86]: DataCenter SP26,Enterprise Edition6,Standard Edition SP26


Y11, 12, 13,14, 15, 16,17, 18, 19

See7, 8, 9, 10

7 Microsoft Windows 2008[x86]: DataCenter6,Enterprise Edition SP26,Standard Edition6


Y11, 12, 13,14, 15, 16,17, 18, 19

See7, 8, 9, 10

1. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.2. The following NICs are not supported: 3COM-3C996B3. iSCSI offload is currently supported on Dell PowerEdge Servers with the Broadcom NetXtreme II Network adapters (based on the Broadcom 5708 and 5709 ASIC) To download the

latest firmware/driver, please visit http://support.dell.com4. Any Microsoft supported server/NIC for the listed operating system revision is supported.5. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.6. Windows Server Core installation option is supported by EMC. Contact your server vendor to determine their support statement for Server Core.7. EMC provides documentation for iSCSI configurations that contains helpful information for using iSCSI with EMC storage. Visit EMC Powerlink and download part number

300-000-603 for the Windows Host Connectivity Guide.8. Powerpath iSCSI 1.1 is supported with Windows 2003 operating systems.9. Powerpath 4.3.1 or higher is supported. All paths may be on a single subnet, or multiple subnets may be used.

10. Microsoft Dynamic Disks are not supported.11. Broadcom iSCSI Boot is supported with the following adapters: Brocade 57712 (2xKR) bNDC, 57800s(2xSFP+/2x1GbT) rNDC, 57810s (2xSFP+) bNDC, 57810s(2xKR) Mezz, 57810







17.

Storage Array


iSCSI Boot from SAN is supported on Fujitsu Siemens Computers Primergy RX300 S3 servers. Contact Fujitsu Siemens Computers support to obtain a list of supported MicrosoftInitiator version and Broadcom boot BIOS versions. iSCSI Boot is supported in Microsoft Clustering Service.



20. Routed networks (layer 3) require iSCSI digest to be enabled.21. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported.22. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" Quorum

Configuration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."23. Driver Version Microsoft iSCSI Initiator NIC teaming with Microsoft iSCSI Initiator is not supported. Native to Windows 2008 Server installation.24. BIOS 1.1425. Driver Version 2.1.4.1926. Firmware Version 3.00.01.4927. Driver Version Microsoft iSCSI Initiator Native to Windows 2008 Server installation. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI Initiator software.28. Driver Version 5.0.2C On BroadCom's 5.0.4.1 CD29. Virtual machines running on VMWare ESX are supported booting from the array.30. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php31. VMWare ESX Server itself is supported booting from external array.32. BIOS 5.0.1133. Firmware Version 2.1.1a34. Powerpath iSCSI 1.1 is not supported with Windows 2000 operating systems.35. BIOS 3.0636. Driver Version 2.1.5.2537. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.38. The lastest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php39. Driver Version Microsoft iSCSI Initiator 2.08 MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later. NIC teaming with Microsoft iSCSI Initiator is not supported. Microsoft iSCSI


40. Driver Version 1.0.48.1 Minimum supported driver version for Cisco UCS mezzanine adapter.41. EMC Celerra supported for Cisco UCS attach.42. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.

Novell NetwareNovell

Novell



EnvironmentExternal

Boot

1 Novell Netware 6.5SP4

Generic Vendor NIC 10/1002, GenericVendor NIC GbE1, 2

LAN Only3 EMC Unified Storage VNXe3300(File/iSCSI)

1.1 N

1. The following NICs are not supported: 3COM-3C996B2. Driver Version 1.4.03. Routed networks (layer 3) require iSCSI digest to be enabled.

Oracle Linux UEK [x86_64]Oracle

Oracle

No.Operating



Boot Comments

1 Oracle LinuxUEK [x86_64]5.76, 34

Emulex OCe10102-IM-E39, 40, 41, Emulex OCe10102-IX-E39, 40, 41 LAN Only2 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

N See9, 28


Emulex OCe11102-IM-E35, 36, 38, 39, Emulex OCe11102-IX-E35, 36, 38, 39 LAN Only2 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

N See9, 28, 37



N See9, 28



N See9, 28, 37


Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)3, 10, 13, 16, QLogic QLA4010-E-SP1, 3, 4, 7, 8,QLogic QLA4010C-E-SP1, 3, 4, 7, 8, QLogic QLA4050-E-SP3, 7, 8, 10, 14, 15,QLogic QLA4050C-E-SP3, 7, 8, 10, 14, 15, QLogic QLA4052C-E-SP3, 7, 8, 10, 14,15, QLogic QLE4060C-E-SP3, 8, 10, 12, 13, 14, QLogic QLE4062C-E-SP3, 8, 10, 12,13, 14


N See9


QLogic QLE8240-SR-E-SP3, 44, 45, QLogic QLE8242-SR-E-SP3, 44, 45, QLogicQLE8250-CU-E-SP3, 44, 45, QLogic QLE8252-CU-E-SP3, 44, 45


N


Generic Vendor NIC 10/10020, Generic Vendor NIC GbE17, 19, 20, 21, HewlettPackard Qlogic QMH4062 1GbE iSCSI HBA for HP c-Class BladeSystem(488074-B21)10, 13, 16, 33


Y29, 30 See9

Storage Array



Generic Vendor NIC 10GbE17, 18, 19, 20 LAN Only2 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y29, 30,31, 32

See9




Y29 See9, 28


QLogic QLA4010-E-SP1, 4, 7, 8, 33, QLogic QLA4010C-E-SP1, 4, 7, 8, 33, QLogicQLA4050-E-SP7, 8, 10, 14, 15, 33, QLogic QLA4050C-E-SP7, 8, 10, 14, 15, 33,QLogic QLA4052C-E-SP7, 8, 10, 14, 15, 33, QLogic QLE4060C-E-SP8, 10, 12, 13,14, 33, QLogic QLE4062C-E-SP8, 10, 12, 13, 14, 33


Y30 See9


Generic Vendor NIC 10/10020, Generic Vendor NIC 10GbE17, 18, 19, 20, GenericVendor NIC GbE17, 19, 20, 21, Hewlett Packard Qlogic QMH4062 1GbE iSCSIHBA for HP c-Class BladeSystem (488074-B21)3, 10, 13, 16, QLogicQLA4010-E-SP1, 3, 4, 7, 8, QLogic QLA4010C-E-SP1, 3, 4, 7, 8, QLogicQLA4050-E-SP3, 7, 8, 10, 14, 15, QLogic QLA4050C-E-SP3, 7, 8, 10, 14, 15, QLogicQLA4052C-E-SP3, 7, 8, 10, 14, 15, QLogic QLE4060C-E-SP3, 8, 10, 12, 13, 14,QLogic QLE4062C-E-SP3, 8, 10, 12, 13, 14


Y See9




Y See9, 28

13 Oracle LinuxUEK [x86_64]:5.76, 34, 5.86,11, 6.16, 42

Generic Vendor NIC 10/10020, Generic Vendor NIC 10GbE17, 18, 19, 20, GenericVendor NIC GbE17, 19, 20, 21


N See9

14 Oracle LinuxUEK [x86_64]:5.76, 34, 5.86,11, 6.16, 42



N See9, 28

15 Oracle LinuxUEK [x86_64]:5.76, 34, 6.16, 42

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)10, 13, 16, 43, QLogic QLA4010-E-SP1, 4, 7, 8, 43,QLogic QLA4010C-E-SP1, 4, 7, 8, 43, QLogic QLA4050-E-SP7, 8, 10, 14, 15, 43,QLogic QLA4050C-E-SP7, 8, 10, 14, 15, 43, QLogic QLA4052C-E-SP7, 8, 10, 14, 15,43, QLogic QLE4060C-E-SP8, 10, 12, 13, 14, 43, QLogic QLE4062C-E-SP8, 10, 12,13, 14, 43


N See9

1. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com2. Routed networks (layer 3) require iSCSI digest to be enabled.3. Driver Version 5.02.14.00.32.01-c0 Driver is integrated into the kernel.4. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com5. Supported kernels: 2.6.32-300.3.1.el6uek, 2.6.32-300.4.1.el6uek, 2.6.32-300.7.1.el6uek, 2.6.32-300.11.1.el6uek, 2.6.32-300.20.1.el6uek, 2.6.32-300.21.1.el6uek. Confirm kernel

support with server vendor.6. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.7. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.8. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com9. Please refer to the Host Bus Adapter note for the supported NICs.

10. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com11. Supported kernels: 2.6.32-300.10.1.el5uek, 2.6.32-300.11.1.el5uek, 2.6.32-300.20.1.el5uek, 2.6.32-300.21.1.el5uek, 2.6.32-300.24.1.el5uek, 2.6.32-300.25.1.el5uek. Confirm

kernel support with server vendor.12. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.13. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com14. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com15. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com16. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com17. Broadcom iSCSI offload (without iboot) is supported with following adapters:


18. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.19. NIC teaming with the Linux software initiator is not supported.20. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.21. Broadcom iSCSI boot is supported on Linux with following adapters:

- Broadcom 5710 based cards- Broadcom 5711 based cardsPlease visit http://support.dell.com for the currently supported servers; as well as, BIOS/firmware versions.

22. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linuxdistributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.

23. Firmware Version 2.1.1a24. BIOS 5.0.1125. Supported kernels: 2.6.32-100.28.1.el6, 2.6.32-100.28.9.el6, 2.6.32-100.28.11.el6, 2.6.32-100.28.15.el6, 2.6.32-100.28.17.el6, 2.6.32-100.35.1.el6uek. Confirm kernel support

with server vendor.26. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php27. Broadcom iSCSI offload (without iboot) is supported with following adapters:


28. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.


30. Broadcom iSCSI boot is supported with following adapters:- Broadcom 57710 based cards- Broadcom 57711 based cards- Broadcom 5708- Broadcom 5709Please visit http://support.dell.com for the currently supported servers; as well as, BIOS/firmware versions.



33. Driver Version 5.02.12.00.32.01-c0 Driver is integrated into the kernel.34.

Storage Array


Supported kernels: 2.6.32-200.13.1.el5uek, 2.6.32-200.16.1.el5uek, 2.6.32-200.19.1.el5uek, 2.6.32-200.20.1.el5uek, 2.6.32-200.23.1.el5uek. Confirm kernel support withserver vendor.

35. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com36. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com37. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.38. Firmware Version 3.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com39. Driver Version 2.103.298.0 Driver is integrated into the kernel. Available in the EMC-approved section of the Emulex website.http://www.emulex.com40. BIOS 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com41. Firmware Version 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com42. Supported kernels: 2.6.32-100.34.1.el6uek. Confirm kernel support with server vendor.43. Driver Version 5.02.12.00.32.01-c0 Driver is integrated into the kernel. Available in the EMC-approved section of the QLogic website.http://www.qlogic.com44. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com45. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com46. Driver Version 4.1.239 Driver is integrated into the kernel.

Oracle Linux [32-Bit]Oracle

Oracle

No.Operating



Boot Comments

1 OracleLinux[32-Bit]5.656, 57, 58


Y15, 23, 25 See1, 26




Y15, 23 See1



Y14, 15, 23,25

See1


IBM IBM Broadcom 10GbE 2-Port Ethernet Expansion Card for IBM BladeCenter(46M6168)33, 34, 35, 36, 37, 38, IBM IBM Broadcom 10GbE 4-Port Ethernet ExpansionCard for IBM BladeCenter (46M6164)33, 34, 35, 36, 37, 38


Y15 See1, 26


QLogic QLA4010-E-SP30, 50, 51, 52, 53, QLogic QLA4010C-E-SP30, 50, 51, 52, 53,QLogic QLA4050-E-SP30, 47, 48, 49, 50, 51, QLogic QLA4050C-E-SP30, 47, 48, 49, 50,51, QLogic QLA4052C-E-SP30, 47, 48, 49, 50, 51, QLogic QLE4060C-E-SP30, 45, 47, 48,51, 54, QLogic QLE4062C-E-SP30, 45, 47, 48, 51, 54


Y23 See1

6 OracleLinux[32-Bit] 5.73

Emulex OCe10102-IM-E27, 28, 39, Emulex OCe10102-IM-E5, 27, 28, EmulexOCe10102-IX-E27, 28, 39, Emulex OCe10102-IX-E5, 27, 28, Generic Vendor NIC10/10040, Generic Vendor NIC 10GbE38, 40, 41, 43, Generic Vendor NIC GbE38, 40,41, 42, Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)31, 44, 45, 47, IBM IBM Broadcom 10GbE 2-Port EthernetExpansion Card for IBM BladeCenter (46M6168)33, 34, 35, 36, 37, 38, IBM IBMBroadcom 10GbE 4-Port Ethernet Expansion Card for IBM BladeCenter(46M6164)33, 34, 35, 36, 37, 38, QLogic QLA4010-E-SP31, 50, 51, 52, 53, QLogicQLA4010C-E-SP31, 50, 51, 52, 53, QLogic QLA4050-E-SP31, 47, 48, 49, 50, 51, QLogicQLA4050C-E-SP31, 47, 48, 49, 50, 51, QLogic QLA4052C-E-SP31, 47, 48, 49, 50, 51,QLogic QLE4060C-E-SP31, 45, 47, 48, 51, 54, QLogic QLE4062C-E-SP31, 45, 47, 48, 51,54


N See1



N See1, 2


QLogic QLE8240-SR-E-SP29, 30, 31, 32, QLogic QLE8240-SR-E-SP29, 31, 32, QLogicQLE8242-SR-E-SP29, 30, 31, 32, QLogic QLE8242-SR-E-SP29, 31, 32, QLogicQLE8250-CU-E-SP29, 30, 31, 32, QLogic QLE8250-CU-E-SP29, 31, 32, QLogicQLE8252-CU-E-SP29, 30, 31, 32, QLogic QLE8252-CU-E-SP29, 31, 32

LAN Only4 EMC UnifiedStorageVNXe3300(File/iSCSI)

N

9 OracleLinux[32-Bit]5.810

Emulex OCe10102-IM-E9, 27, 28, Emulex OCe10102-IX-E9, 27, 28, IBM IBMBroadcom 10GbE 2-Port Ethernet Expansion Card for IBM BladeCenter(46M6168)33, 34, 35, 36, 37, 38, IBM IBM Broadcom 10GbE 4-Port Ethernet ExpansionCard for IBM BladeCenter (46M6164)33, 34, 35, 36, 37, 38


Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

See1, 26



Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

See1, 2, 26


Generic Vendor NIC 10/10040, Generic Vendor NIC 10GbE38, 40, 41, 43, GenericVendor NIC GbE38, 40, 41, 42, Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBAfor HP c-Class BladeSystem (488074-B21)44, 45, 46, 47, QLogic QLA4010-E-SP46, 50,51, 52, 53, QLogic QLA4010C-E-SP46, 50, 51, 52, 53, QLogic QLA4050-E-SP46, 47, 48,49, 50, 51, QLogic QLA4050C-E-SP46, 47, 48, 49, 50, 51, QLogic QLA4052C-E-SP46, 47,48, 49, 50, 51, QLogic QLE4060C-E-SP45, 46, 47, 48, 51, 54, QLogic QLE4062C-E-SP45,46, 47, 48, 51, 54


Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

See1




Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

1. Please refer to the Host Bus Adapter note for the supported NICs.2. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.3. Supported kernels: 2.6.18-274.0.0.0.1.el5, 2.6.18-274.12.1.0.1.el5, 2.6.18-274.17.1.0.1.el5. Confirm kernel support with server vendor.4. Routed networks (layer 3) require iSCSI digest to be enabled.5. Driver Version 4.0.100r Driver is integrated into the kernel.6. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com7. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com

Storage Array


8. Firmware Version 3.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com9. Driver Version 4.1.239 Driver is integrated into the kernel.

10. Supported kernels: 2.6.18-308.0.0.0.1.el5. Confirm kernel support with server vendor.11. iSCSI Boot from SAN is supported on certain IBM Servers BladeCenter models. Contact IBM support to obtain a list of supported blades and Microsoft

Initiator version12. Servers booting from external storage with QLA4010 iSCSI boards require Microsoft iSCSI Initiator 2.0 or 2.02 service to be installed. Note that HBA IQN must be altered prior to

Windows installation. Refer to EMC Host Connectivity Guide for information on changing IQN and setting up boot for servers requiring MS iSCSI Initiator service.13. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168




16. VMWare ESX Server itself is supported booting from external array.17. iSCSI Boot from SAN is supported on Fujitsu Siemens Computers Primergy RX300 S3 servers. Contact Fujitsu Siemens Computers support to obtain a list of supported Microsoft

Initiator version and Broadcom boot BIOS versions. iSCSI Boot is supported in Microsoft Clustering Service.18. Intel iSCSI boot is supported on Fujitsu Technology Solutions servers with the following Intel Adapters: 82575, 82576 iSCSI supported with W2008 and W2008 R2. Please visit

http://www.ts.fujitsu.com for the most currently supported servers and firmware/driver revisions.19. Intel iSCSI boot is supported on Oracle servers with the following Intel Adapters: . X1106A-Z (10 GbE 1-port SR Oplin/ Belle Fountaine), X1107A-Z (10 GbE 2-port SR Oplin/ Green

Fountaine), X1108A-Z (10 GbE dual-port EM Longwater). X5561A-ZSFP + SR Transceiver; required for X1108A-Z) iSCSI supported with W2008 and W2008 R2. Please visithttp://www.intel.com for the most currently supported firmware/driver revisions.

20. Virtual machines running on VMWare ESX are supported booting from the array.21. Intel iSCSI boot is supported on Dell servers with the following adapters: PRO/1000 PF, PRO/1000 PT, PRO/1000 PT dual port, PRO/ 1000 VT quad port, Ethernet X520 10GbE Dual

Port KX4 and Ethernet Server Adapter X520-2 10GbE Please visithttp://support.dell.com for the most currently supported servers and firmware/driver revisions.22. iSCSI Boot is supported with on Cisco UCS B-Series blades using the M81KR23. Broadcom iSCSI boot is supported with following adapters:





27. BIOS 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com28. Firmware Version 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com29. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com30. Driver Version 5.02.04.02.05.06-d0 Driver is integrated into the kernel.31. Driver Version 5.02.04.01.05.07-d0 Driver is integrated into the kernel.32. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com33. BIOS 5.0.1134. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.35. Firmware Version 2.1.1a36. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php37. Broadcom iSCSI offload (without iboot) is supported with following adapters:


38. NIC teaming with the Linux software initiator is not supported.39. Driver Version 4.0.100 Driver is integrated into the kernel.40. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.41. Broadcom iSCSI offload (without iboot) is supported with following adapters:



43. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.44. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com45. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com46. Driver Version 5.02.04.02.05.08-d0 Driver is integrated into the kernel.47. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com48. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com49. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com50. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.51. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com52. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com53. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com54. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.55. Driver Version 2.0.549.0 Driver is integrated into the kernel.56. Supported kernels: 2.6.18-238.0.1.el5, 2.6.18-238.1.1.0.1.el5, 2.6.18-238.5.1.0.1.el5, 2.6.18-238.9.1.0.1.el5, 2.6.18-238.12.1.0.1.el5. Confirm kernel support with server vendor.57. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.58. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.

Oracle Linux [x86_64]Oracle

Oracle

No.Operating



Boot Comments

1 OracleLinux[x86_64]5.655, 56, 57


Y14, 23, 25 See6, 26

Storage Array


2 OracleLinux[x86_64]5.655, 56, 57



Y14, 23 See6

3 OracleLinux[x86_64]5.655, 56, 57


Y14, 15, 23,25

See6

4 OracleLinux[x86_64]5.655, 56, 57

IBM IBM Broadcom 10GbE 2-Port Ethernet Expansion Card for IBM BladeCenter(46M6168)33, 34, 35, 36, 37, 38, IBM IBM Broadcom 10GbE 4-Port Ethernet ExpansionCard for IBM BladeCenter (46M6164)33, 34, 35, 36, 37, 38


Y14 See6, 26

5 OracleLinux[x86_64]5.655, 56, 57

QLogic QLA4010-E-SP30, 50, 51, 52, 53, QLogic QLA4010C-E-SP30, 50, 51, 52, 53,QLogic QLA4050-E-SP30, 46, 48, 49, 50, 51, QLogic QLA4050C-E-SP30, 46, 48, 49, 50,51, QLogic QLA4052C-E-SP30, 46, 48, 49, 50, 51, QLogic QLE4060C-E-SP30, 44, 46, 48,51, 54, QLogic QLE4062C-E-SP30, 44, 46, 48, 51, 54


Y23 See6

6 OracleLinux[x86_64]5.75

Emulex OCe10102-IM-E1, 27, 28, Emulex OCe10102-IM-E27, 28, 39, EmulexOCe10102-IX-E1, 27, 28, Emulex OCe10102-IX-E27, 28, 39, Generic Vendor NIC10/10040, Generic Vendor NIC 10GbE38, 40, 41, 43, Generic Vendor NIC GbE38, 40,41, 42, Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)31, 44, 46, 47, IBM IBM Broadcom 10GbE 2-Port EthernetExpansion Card for IBM BladeCenter (46M6168)33, 34, 35, 36, 37, 38, IBM IBMBroadcom 10GbE 4-Port Ethernet Expansion Card for IBM BladeCenter(46M6164)33, 34, 35, 36, 37, 38, QLogic QLA4010-E-SP31, 50, 51, 52, 53, QLogicQLA4010C-E-SP31, 50, 51, 52, 53, QLogic QLA4050-E-SP31, 46, 48, 49, 50, 51, QLogicQLA4050C-E-SP31, 46, 48, 49, 50, 51, QLogic QLA4052C-E-SP31, 46, 48, 49, 50, 51,QLogic QLE4060C-E-SP31, 44, 46, 48, 51, 54, QLogic QLE4062C-E-SP31, 44, 46, 48, 51,54


N See6



N See6, 7


QLogic QLE8240-SR-E-SP29, 30, 31, 32, QLogic QLE8240-SR-E-SP29, 31, 32, QLogicQLE8242-SR-E-SP29, 30, 31, 32, QLogic QLE8242-SR-E-SP29, 31, 32, QLogicQLE8250-CU-E-SP29, 30, 31, 32, QLogic QLE8250-CU-E-SP29, 31, 32, QLogicQLE8252-CU-E-SP29, 30, 31, 32, QLogic QLE8252-CU-E-SP29, 31, 32


N


Emulex OCe10102-IM-E10, 27, 28, Emulex OCe10102-IX-E10, 27, 28, IBM IBMBroadcom 10GbE 2-Port Ethernet Expansion Card for IBM BladeCenter(46M6168)33, 34, 35, 36, 37, 38, IBM IBM Broadcom 10GbE 4-Port Ethernet ExpansionCard for IBM BladeCenter (46M6164)33, 34, 35, 36, 37, 38


Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

See6, 26



Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

See6, 7, 26


Generic Vendor NIC 10/10040, Generic Vendor NIC 10GbE38, 40, 41, 43, GenericVendor NIC GbE38, 40, 41, 42, Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBAfor HP c-Class BladeSystem (488074-B21)44, 45, 46, 47, QLogic QLA4010-E-SP45, 50,51, 52, 53, QLogic QLA4010C-E-SP45, 50, 51, 52, 53, QLogic QLA4050-E-SP45, 46, 48,49, 50, 51, QLogic QLA4050C-E-SP45, 46, 48, 49, 50, 51, QLogic QLA4052C-E-SP45, 46,48, 49, 50, 51, QLogic QLE4060C-E-SP44, 45, 46, 48, 51, 54, QLogic QLE4062C-E-SP44,45, 46, 48, 51, 54


Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

See6




Y11, 12, 13,14, 15, 16, 17,18, 19, 20, 21,22, 23, 24, 25

1. Driver Version 4.0.100r Driver is integrated into the kernel.2. Firmware Version 3.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com3. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com4. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com5. Supported kernels: 2.6.18-274.0.0.0.1.el5, 2.6.18-274.12.1.0.1.el5, 2.6.18-274.17.1.0.1.el5. Confirm kernel support with server vendor.6. Please refer to the Host Bus Adapter note for the supported NICs.7. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.8. Routed networks (layer 3) require iSCSI digest to be enabled.9. Supported kernels: 2.6.18-308.0.0.0.1.el5. Confirm kernel support with server vendor.

10. Driver Version 4.1.239 Driver is integrated into the kernel.11. iSCSI Boot from SAN is supported on certain IBM Servers BladeCenter models. Contact IBM support to obtain a list of supported blades and Microsoft







17. VMWare ESX Server itself is supported booting from external array.18. Intel iSCSI boot is supported on Fujitsu Technology Solutions servers with the following Intel Adapters: 82575, 82576 iSCSI supported with W2008 and W2008 R2. Please visit






Storage Array





27. BIOS 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com28. Firmware Version 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com29. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com30. Driver Version 5.02.04.02.05.06-d0 Driver is integrated into the kernel.31. Driver Version 5.02.04.01.05.07-d0 Driver is integrated into the kernel.32. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com33. BIOS 5.0.1134. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.35. Firmware Version 2.1.1a36. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php37. Broadcom iSCSI offload (without iboot) is supported with following adapters:


38. NIC teaming with the Linux software initiator is not supported.39. Driver Version 4.0.100 Driver is integrated into the kernel.40. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux




43. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.44. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com45. Driver Version 5.02.04.02.05.08-d0 Driver is integrated into the kernel.46. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com47. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com48. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com49. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com50. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.51. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com52. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com53. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com54. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.55. Supported kernels: 2.6.18-238.0.1.el5, 2.6.18-238.1.1.0.1.el5, 2.6.18-238.5.1.0.1.el5, 2.6.18-238.9.1.0.1.el5, 2.6.18-238.12.1.0.1.el5. Confirm kernel support with server vendor.56. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.57. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.58. Driver Version 2.0.549.0 Driver is integrated into the kernel.

Oracle SolarisOracle

Oracle

No.Operating



StorageOperative

EnvironmentExternal

Boot Comments

1 Oracle Solaris 10SPARC18, 19, 20,21

Generic Vendor NIC GbE24 LAN Only1 EMC UnifiedStorageVNXe3300(File/iSCSI)

N See23

2 Oracle Solaris 10SPARC18, 20, 21

Generic Vendor NIC X1106A-Z (Sun 10 GbE)24, Generic VendorNIC X1107A-Z (Sun Dual 10 GbE)24, Generic Vendor X1108A-Z(Sun 10GbE EM)24, QLogic QLE8140-SR-E-SP (CNA)24, 26, 27,QLogic QLE8142-SR-E-SP (CNA)24, 26, 27, QLogicQLE8150-CU-E-SP (CNA)24, 26, 27


N See23

3 Oracle Solaris 10SPARC20

Generic Vendor NIC 10/10028, 30, Generic Vendor NIC GbE28, 30 LAN Only1, 29 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

4 Oracle Solaris 10SPARC20, 21, 25

Emulex OCe10102-FM-E (CNA)24, 33, Emulex OCe10102-FX-E(CNA)24, 33, Oracle SG-(X)EMFCOE2-Q-SR (QEM8152)24, 32,Oracle SG-(X)EMFCOE2-Q-TA14, 24, 32, OracleSG-XPCIEFCOE2-Q-SR (QLE8142 CNA)24, 32, OracleSG-XPCIEFCOE2-Q-TA (QLE8152 CNA)14, 24, 32


N See23

5 Oracle Solaris 10x8611, 12, 13

Generic Vendor NIC X1106A-Z (Sun 10 GbE)8, Generic VendorNIC X1107A-Z (Sun Dual 10 GbE)8, Generic Vendor X1108A-Z(Sun 10GbE EM)8


N See6

6 Oracle Solaris 10x8611, 13, 15

Emulex OCe10102-FM-E (CNA)8, 17, Emulex OCe10102-FX-E(CNA)8, 17, Oracle SG-(X)EMFCOE2-Q-SR (QEM8152)8, 16,Oracle SG-(X)EMFCOE2-Q-TA8, 14, 16, OracleSG-XPCIEFCOE2-Q-SR (QLE8142 CNA)8, 16, OracleSG-XPCIEFCOE2-Q-TA (QLE8152 CNA)8, 14, 16


N See6

7 Oracle Solaris 10x8610, 11, 12, 13

Generic Vendor NIC GbE8, QLogic QLE8140-SR-E-SP (CNA)8,27, 31, QLogic QLE8142-SR-E-SP (CNA)8, 27, 31, QLogicQLE8150-CU-E-SP (CNA)8, 27, 31


N See6

8 Oracle Solaris 10:SPARC18, 19, 20,21, SPARC18, 20,21, SPARC20, 21,25

QLogic QLE8240-SR-E-SP7, 9, 22, 24, QLogicQLE8242-SR-E-SP7, 9, 22, 24, QLogic QLE8250-CU-E-SP7, 9, 22,24, QLogic QLE8252-CU-E-SP7, 9, 22, 24


N See23

Storage Array


9 Oracle Solaris 10:x8611, 13, 15,x8610, 11, 12, 13

QLogic QLE8240-SR-E-SP5, 7, 8, 9, QLogic QLE8242-SR-E-SP5,7, 8, 9, QLogic QLE8250-CU-E-SP5, 7, 8, 9, QLogicQLE8252-CU-E-SP5, 7, 8, 9


N See6

10 Oracle Solaris 11:SPARC4, x862

Emulex OCe10102-FM-E (CNA)3, Emulex OCe10102-FX-E(CNA)3, Generic Vendor NIC GbE3, Generic Vendor NICX1106A-Z (Sun 10 GbE)3, Generic Vendor NIC X1107A-Z (SunDual 10 GbE)3, Generic Vendor X1108A-Z (Sun 10GbE EM)3,Oracle SG-(X)EMFCOE2-Q-SR (QEM8152)3, OracleSG-(X)EMFCOE2-Q-TA3, 14, Oracle SG-XPCIEFCOE2-Q-SR(QLE8142 CNA)3, Oracle SG-XPCIEFCOE2-Q-TA (QLE8152CNA)3, 14


N

1. Routed networks (layer 3) require iSCSI digest to be enabled.2. EMC recommends as a best practice that customers upgrade to the most recent Solaris 11 x86 SRU released on the Oracle website:http://support.oracle.com3. Driver Version Native OS Driver4. EMC recommends as a best practice that customers upgrade to the most recent Solaris 11 SPARC SRU released on the Oracle website:http://support.oracle.com5. Require the ethernet driver qlge patch 145649-03 or later.6. Solaris 10_x86 native iSCSI with MPxIO requires minimum patch 125185-05.7. BIOS 3.038. Driver Version Native OS Driver Support Solaris 10_x86 native iSCSI driver patch 146233-08, 146233-11, and 146233-12.9. Firmware Version 04.08.14

10. Supports S10_x86 Update 2 (06/06), S10_x86 Update 3 (11/06), S10_x86 Update 4 (08/07), S10_x86 Update 5 (05/08), S10_x86 Update 6 (10/08) and S10_x86 Update 7 (05/09).11. EMC recommends as a best practice that customers upgrade to the most recent Solaris 10 x86 patch bundle released on the Oracle website:http://www.sunsolve.sun.com12. Supports S10_x86 Update 8 (10/09).13. EMC supports ZFS in Solaris 10_x86 11/06 (update 3) or later. The Snapshot and Clone features of ZFS are supported only through Sun Microsystems.14. Copper connection only. Supported with Passive and Active Twinax cables.15. Supports Solaris 10_x86 Update 8 (10/09), Solaris 10_x86 Update 9 (9/10).16. Require the Ethernet driver patch 144870-02 or later.17. Require the Ethernet driver patch 145099-01 or later.18. Supports S10 Update 8 (10/09).19. Supports S10 Update 2 (06/06), S10 Update 3 (11/06), S10 Update 4 (08/07), S10 Update 5 (05/08), S10 Update 6 (10/08) and S10 Update 7 (05/09).20. For LDOM support, please refer to the 'Virtualization Server Support' table available via EMC PowerLink:

https://elabnavigator.emc.com/emcpubs/elab/esm/pdf/Virtualization_Server_Support.pdf21. EMC recommends as a best practice that customers upgrade to the most recent Solaris 10 SPARC patch bundle released on the Oracle website:http://www.sunsolve.sun.com22. Require the ethernet driver qlge patch 145648-03 or later.23. Solaris SPARC native iSCSI with MPxIO requires minimum patch 125184-05.24. Driver Version Native OS Driver Support Solaris 10 Sparc native iSCSI driver patch 146232-09, 146232-12, and 146232-13.25. Supports Solaris 10 Update 8 (10/09), Solaris 10 Update 9 (9/10).26. Require the Ethernet driver patch 144486-04 or later.27. BIOS 2.1628. Driver Version included in OS29. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.30. The following NICs are not supported: 3COM-3C996B31. Require the Ethernet driver patch 144487-04 or later.32. Require the Ethernet driver patch 144869-02 or later.33. Require the Ethernet driver patch 145098-01 or later.

Red Hat RHEL [32-Bit]Red Hat

Red Hat



StorageOperative

EnvironmentExternal

Boot Comments

1 Red Hat RHEL[32-Bit] 3.0 U7AS/ES76, 77, 84

Generic Vendor NIC 10/10080, Generic Vendor NICGbE79, QLogic QLA4010-E-SP83, QLogicQLA4010-E-SP85, QLogic QLA4010C-E-SP83, QLogicQLA4010C-E-SP85


1.1 N See75


QLogic QLA4010-E-SP83, QLogic QLA4010-E-SP85,QLogic QLA4010C-E-SP83, QLogic QLA4010C-E-SP85,QLogic QLA4050-E-SP9, 10, 85, QLogic QLA4050C-E-SP9,10, 85, QLogic QLA4052C-E-SP9, 10, 85


1.1 Y See47, 75


QLogic QLA4050-E-SP9, 10, 93, QLogic QLA4050C-E-SP9,10, 93, QLogic QLA4052C-E-SP9, 10, 93


1.1 Y See47, 75

4 Red Hat RHEL[32-Bit] 3.9AS/ES76, 77, 78

QLogic QLA4010-E-SP9, 10, 74, QLogic QLA4010C-E-SP9,10, 74


1.1 N See75

5 Red Hat RHEL[32-Bit] 3.9AS/ES76, 77, 78

QLogic QLA4010-E-SP9, 10, 74, QLogic QLA4010C-E-SP9,10, 74, QLogic QLA4050-E-SP9, 10, 74, QLogicQLA4050C-E-SP9, 10, 74, QLogic QLA4052C-E-SP9, 10, 74


1.1 Y See47, 75

6 Red Hat RHEL[32-Bit] 4.0 U4AS/ES76, 87

QLogic QLA4050-E-SP9, 10, 89, 91, QLogicQLA4050-E-SP9, 10, 91, QLogic QLA4050C-E-SP9, 10, 89,91, QLogic QLA4050C-E-SP9, 10, 91, QLogicQLA4052C-E-SP9, 10, 89, 91, QLogic QLA4052C-E-SP9, 10,91


1.1 Y See47, 75

7 Red Hat RHEL[32-Bit] 4.0: U2AS/ES76, 92, U3AS/ES76, 90

QLogic QLA4050-E-SP9, 10, 89, QLogic QLA4050C-E-SP9,10, 89, QLogic QLA4052C-E-SP9, 10, 89


1.1 Y See47, 75

8 Red Hat RHEL[32-Bit] 4.0: U2AS/ES76, 92, U3AS/ES76, 90, U4AS/ES76, 87

Generic Vendor NIC 10/10088, Generic Vendor NICGbE86

LAN Only1, 47 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

9 Red Hat RHEL[32-Bit] 5.535, 36, 37

Emulex OCe10102-IM-E55, 57, 108, EmulexOCe10102-IX-E55, 57, 108


Y2, 33, 43 See3, 34

10 Red Hat RHEL[32-Bit] 5.67, 8



Y2, 33, 43 See3, 34

Storage Array



Emulex OCe11102-IM-E58, 60, 61, 63, EmulexOCe11102-IX-E58, 60, 61, 63


Y33 See3, 34, 59


Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA forHP c-Class BladeSystem (488074-B21)4, 11, 17, 45


Y2, 33 See3


QLogic QLA4010-E-SP4, 9, 10, 19, 20, QLogicQLA4010C-E-SP4, 9, 10, 19, 20, QLogic QLA4050-E-SP4, 5,6, 9, 10, 11, QLogic QLA4050C-E-SP4, 5, 6, 9, 10, 11, QLogicQLA4052C-E-SP4, 5, 6, 9, 10, 11, QLogic QLE4060C-E-SP4,6, 10, 11, 16, 17, QLogic QLE4062C-E-SP4, 6, 10, 11, 16, 17


Y2 See3


QLogic QLE8240-SR-E-SP4, 23, 24, QLogicQLE8242-SR-E-SP4, 23, 24, QLogic QLE8250-CU-E-SP4,23, 24, QLogic QLE8252-CU-E-SP4, 23, 24


N




Y2, 33, 43 See3, 34




Y33 See3, 34, 59




Y2, 33 See3


QLogic QLA4010-E-SP9, 10, 19, 20, 54, QLogicQLA4010C-E-SP9, 10, 19, 20, 54, QLogic QLA4050-E-SP5,6, 9, 10, 11, 54, QLogic QLA4050C-E-SP5, 6, 9, 10, 11, 54,QLogic QLA4052C-E-SP5, 6, 9, 10, 11, 54, QLogicQLE4060C-E-SP6, 10, 11, 16, 17, 54, QLogicQLE4062C-E-SP6, 10, 11, 16, 17, 54


Y2 See3


QLogic QLE8240-SR-E-SP23, 24, 54, QLogicQLE8242-SR-E-SP23, 24, 54, QLogicQLE8250-CU-E-SP23, 24, 54, QLogicQLE8252-CU-E-SP23, 24, 54


N


Emulex OCe10102-IM-E55, 57, 107, EmulexOCe10102-IX-E55, 57, 107, IBM IBM Broadcom 10GbE2-Port Ethernet Expansion Card for IBM BladeCenter(46M6168)27, 28, 29, 30, 31, 32, IBM IBM Broadcom 10GbE4-Port Ethernet Expansion Card for IBM BladeCenter(46M6164)27, 28, 29, 30, 31, 32


Y2, 33, 42, 43,96, 97, 98, 99,100, 101, 102,103, 104, 105,106

See3, 34




Y2, 33, 42, 43,96, 97, 98, 99,100, 101, 102,103, 104, 105,106

See3, 34, 59


Generic Vendor NIC 10/10038, Generic Vendor NIC10GbE29, 38, 39, 41, Generic Vendor NIC GbE29, 38, 39, 40,Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA forHP c-Class BladeSystem (488074-B21)11, 17, 45, 94,QLogic QLA4010-E-SP9, 10, 19, 20, 94, QLogicQLA4010C-E-SP9, 10, 19, 20, 94, QLogic QLA4050-E-SP5,6, 9, 10, 11, 94, QLogic QLA4050C-E-SP5, 6, 9, 10, 11, 94,QLogic QLA4052C-E-SP5, 6, 9, 10, 11, 94, QLogicQLE4060C-E-SP6, 10, 11, 16, 17, 94, QLogicQLE4062C-E-SP6, 10, 11, 16, 17, 94


Y2, 33, 42, 43,96, 97, 98, 99,100, 101, 102,103, 104, 105,106

See3


QLogic QLE8240-SR-E-SP23, 24, 94, QLogicQLE8242-SR-E-SP23, 24, 94, QLogicQLE8250-CU-E-SP23, 24, 94, QLogicQLE8252-CU-E-SP23, 24, 94


Y2, 33, 42, 43,96, 97, 98, 99,100, 101, 102,103, 104, 105,106

24 Red Hat RHEL[32-Bit] 6.112, 13, 14,15



Y2, 33 See3

25 Red Hat RHEL[32-Bit] 6.112, 13, 14,15



Y2 See3

26 Red Hat RHEL[32-Bit] 6.213, 14, 15,65, 66



Y2, 33 See3

27 Red Hat RHEL[32-Bit] 6.213, 14, 15,65, 66



Y2 See3

Storage Array


28 Red Hat RHEL[32-Bit] 6.213, 14, 15,65, 66

QLogic QLE8240-SR-E-SP23, 24, 64, QLogicQLE8250-CU-E-SP23, 24, 64, QLogicQLE8252-CU-E-SP23, 24, 64


N

29 Red Hat RHEL[32-Bit] 6.313, 14, 15,22

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT)rNDC (rack)30, 67, 68, Broadcom Broadcom 57810 DP10Gb DA/SFP+ CNA30, 67, 68, Dell Broadcom 57810 DualPort 10GbE KR Blade Converged Mezz30, 67, 68


Y2, 33, 42, 43 See3, 34

30 Red Hat RHEL[32-Bit] 6.313, 14, 15,22

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT)rNDC (rack)30, 67, 68, Broadcom Broadcom 57810 DP10Gb DA/SFP+ CNA30, 67, 68, Dell Broadcom 57810 DualPort 10GbE KR Blade Converged Mezz30, 67, 68, QLogicQLE8240-SR-E-SP21, 23, 24, QLogicQLE8242-SR-E-SP21, 23, 24, QLogicQLE8250-CU-E-SP21, 23, 24, QLogicQLE8252-CU-E-SP21, 23, 24


N

31 Red Hat RHEL[32-Bit] 6.313, 14, 15,22



Y2, 33 See3

32 Red Hat RHEL[32-Bit] 6.313, 14, 15,22

QLogic QLA4010-E-SP9, 10, 19, 20, 21, QLogicQLA4010C-E-SP9, 10, 19, 20, 21, QLogic QLA4050-E-SP5,6, 9, 10, 11, 21, QLogic QLA4050C-E-SP5, 6, 9, 10, 11, 21,QLogic QLA4052C-E-SP5, 6, 9, 10, 11, 21, QLogicQLE4060C-E-SP6, 10, 11, 16, 17, 18, 21, QLogicQLE4062C-E-SP6, 10, 11, 16, 17, 21


Y2 See3

33 Red Hat RHEL[32-Bit]: 3.0 U8AS/ES76, 77, 81, 3.9AS/ES76, 77, 78

Generic Vendor NIC 10/10029, 80, Generic Vendor NICGbE29, 79


1.1 N See75

34 Red Hat RHEL[32-Bit]: 4.5AS/ES76, 82, 4.6AS/ES73, 4.7AS/ES69, 4.8AS/ES51



1.1 N

35 Red Hat RHEL[32-Bit]: 5.036, 72,5.136, 71, 5.214, 36,70, 5.336, 49, 5.436,46

Generic Vendor NIC 10/10029, 38, Generic Vendor NICGbE48


1.1 N

36 Red Hat RHEL[32-Bit]: 5.535, 36,37, 5.67, 8, 5.78, 53,6.013, 14, 15, 26,6.112, 13, 14, 15,6.213, 14, 15, 65, 66,6.313, 14, 15, 22

Generic Vendor NIC 10/10038, Generic Vendor NICGbE29, 38, 39, 40


Y2, 33 See3

37 Red Hat RHEL[32-Bit]: 5.535, 36,37, 5.67, 8, 5.78, 53,6.013, 14, 15, 26,6.112, 13, 14, 15,6.213, 14, 15, 65, 66,6.313, 14, 15, 22


Y2, 33, 42, 43 See3

38 Red Hat RHEL[32-Bit]: 5.535, 36,37, 5.67, 8, 5.78, 53,6.013, 14, 15, 26,6.112, 13, 14, 15,6.213, 14, 15, 65, 66,6.313, 14, 15, 22

IBM IBM Broadcom 10GbE 2-Port Ethernet ExpansionCard for IBM BladeCenter (46M6168)27, 28, 29, 30, 31, 32,IBM IBM Broadcom 10GbE 4-Port Ethernet ExpansionCard for IBM BladeCenter (46M6164)27, 28, 29, 30, 31, 32


Y33 See3, 34

39 Red Hat RHEL[32-Bit]: 5.535, 36,37, 6.013, 14, 15, 26



Y2, 33 See3

40 Red Hat RHEL[32-Bit]: 5.535, 36,37, 6.013, 14, 15, 26



Y2 See3

41 Red Hat RHEL[32-Bit]: 6.013, 14,15, 26, 6.112, 13, 14,15

QLogic QLE8240-SR-E-SP23, 24, 25, QLogicQLE8250-CU-E-SP23, 24, 25, QLogicQLE8252-CU-E-SP23, 24, 25


N

42 Red Hat RHEL[32-Bit]: 6.013, 14,15, 26, 6.112, 13, 14,15, 6.213, 14, 15, 65,66

QLogic QLE8242-SR-E-SP23, 24, 25 LAN Only1 EMC UnifiedStorageVNXe3300(File/iSCSI)

N

1. Routed networks (layer 3) require iSCSI digest to be enabled.2. Broadcom iSCSI boot is supported with following adapters:


3. Please refer to the Host Bus Adapter note for the supported NICs.4. Driver Version 5.02.04.02.05.06-d0 Driver is integrated into the kernel.5. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com6. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com7. Supported kernels: 2.6.18-238.el5, 2.6.18-238.1.1.el5, 2.6.18-238.5.1.el5, 2.6.18-238.9.1.el5, 2.6.18-238.12.1.el5, 2.6.18-238.19.1.el5, 2.6.18-238.21.1.el5, 2.6.18-238.27.1.el5,

2.6.18-238.28.1.el5, 2.6.18-238.31.1.el5, 2.6.18-238.33.1.el5, 2.6.18-238.35.1.el5, 2.6.18-238.37.1.el5. Confirm kernel support with server vendor.8. EMC supports the following filesystems: ext2, ext3, ext4, xfs, and gfs unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please submit

an RPQ.9. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.

10. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com11. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com12. Supported kernels: 2.6.32-131.0.15.el6, 2.6.32-131.2.1.el6, 2.6.32-131.6.1.el6, 2.6.32-131.12.1.el6, 2.6.32-131.17.1.el6, 2.6.32-131.21.1.el6, 2.6.32-131.25.1.el6. Confirm kernel

support with server vendor.

Storage Array


13. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.14. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.15. EMC supports the following filesystems: ext2, ext3, ext4, xfs, gfs, and gfs2 unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please

submit an RPQ.16. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.17. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com18. Driver Version 5.02.00-k5 Driver is integrated into the kernel.19. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com20. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com21. Driver Version 5.02.00.00.06.03-k4 Driver is integrated into the kernel.22. Supported kernels: 2.6.32-279.el6. Confirm kernel support with server vendor.23. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com24. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com25. Driver Version 5.02.11.00.05.06-c3 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com26. Supported kernels: 2.6.32-71.el6, 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6, 2.6.32-71.24.1.el6, 2.6.32-71.31.1.el6, 2.6.32-71.34.1.el6,

2.6.32-71.36.1.el6, 2.6.32-71.37.1.el6, 2.6.32-71.38.1.el6. Confirm kernel support with server vendor.27. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php28. Broadcom iSCSI offload (without iboot) is supported with following adapters:


29. NIC teaming with the Linux software initiator is not supported.30. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.31. Firmware Version 2.1.1a32. BIOS 5.0.1133. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

iSCSI boot is supported with Red Hat RHEL 5.5Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.


35. EMC supports the following filesystems: ext2, ext3, xfs, and gfs unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please submit anRPQ.

36. EMC supports the following filesystems: ext2, ext3, gfs unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please submit an RPQ.37. Supported kernels: 2.6.18-194.el5, 2.6.18-194.3.1.el5, 2.6.18-194.8.1.el5, 2.6.18-194.11.1.el5, 2.6.18-194.11.3.el5, 2.6.18-194.11.4.el5, 2.6.18-194.17.1.el5, 2.6.18-194.17.4.el5,

2.6.18-194.26.1.el5, 2.6.18-194.32.1.el5 Confirm kernel support with server vendor.38. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux




41. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.42. Intel iSCSI boot is supported on Oracle servers with the following Intel Adapters: . X1106A-Z (10 GbE 1-port SR Oplin/ Belle Fountaine), X1107A-Z (10 GbE 2-port SR Oplin/ Green

Fountaine), X1108A-Z (10 GbE dual-port EM Longwater). X5561A-ZSFP + SR Transceiver; required for X1108A-Z) iSCSI. Please visithttp://www.intel.com for the most currentlysupported firmware/driver revisions.


44. Driver Version 5.01.00.01.05.04-k9 Driver is integrated into the kernel.45. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com46. Supported kernels: 2.6.18-164.el5, 2.6.18-164.2.1.el5, 2.6.18-164.6.1.el5, 2.6.18-164.9.1.el5, 2.6.18-164.10.1.el5, 2.6.18-164.11.1.el5, 2.6.18-164.15.1.el5, 2.6.18-164.17.1.el5,

2.6.18-164.25.1.el5, 2.6.18-164.25.2.el5. Confirm kernel support with server vendor.47. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.48. Driver Version iSCSI Software Initiator 1.0-595 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please

refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library ->Host Connectivity for the complete installation information.

49. Supported kernels: 2.6.18-128.el5, 2.6.18-128.1.1.el5, 2.6.18-128.1.6.el5, 2.6.18-128.1.10.el5, 2.6.18-128.1.14.el5, 2.6.18-128.1.16.el5, 2.6.18-128.2.1.el5, 2.6.18-128.4.1.el5,2.6.18-128.7.1.el5, 2.6.18-128.17.1.el5, 2.6.18-128.23.1.el5, 2.6.18-128.23.2.el5, 2.6.18-128.26.1.el5. Confirm kernel support with server vendor.

50. Driver Version iSCSI initiator 4.0.1.11 Driver is integrated into the kernel. The following NICs are not supported: 3COM-3C996B The software initiator is part of the operating systemand not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlinkwebsite in Support -> The Document Library -> Host Connectivity for the complete installation information.

51. Supported kernels: 2.6.9-89.EL, 2.6.9-89.0.3.EL, 2.6.9-89.0.7.EL, 2.6.9-89.0.9EL, 2.6.9-89.0.11.EL, 2.6.9-89.0.15.EL, 2.6.9-89.0.16.EL, 2.6.9-89.0.18.EL, 2.6.9-89.0.19.EL,2.6.9-89.0.20.EL, 2.6.9-89.0.23.EL, 2.6.9-89.0.25.EL, 2.6.9-89.0.26.EL, 2.6.9-89.0.28.EL, 2.6.9-89.0.29.EL, 2.6.9-89.29.1.EL, 2.6.9-89.31.1.EL, 2.6.9-89.33.1.EL, 2.6.9-89.35.1.EL.Confirm kernel support with server vendor.

52. Driver Version iSCSI initiator 4.0.1.11 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please refer to therequired release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> HostConnectivity for the complete installation information.

53. Supported kernels: 2.6.18-274.el5, 2.6.18-274.3.1el5, 2.6.18-274.7.1.el5, 2.6.18-274.12.1.el5, 2.6.18-274.17.1.el5, 2.6.18-274.18.1.el5. Confirm kernel support with server vendor.54. Driver Version 5.02.04.01.05.07-d0 Driver is integrated into the kernel.55. BIOS 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com56. Driver Version 4.0.100 Driver is integrated into the kernel.57. Firmware Version 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com58. Firmware Version 3.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com59. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.60. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com61. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com62. Driver Version 4.0.100r Driver is integrated into the kernel.63. Driver Version 2.0.549.0 Driver is integrated into the kernel.64. Driver Version 5.02.00.00.06.02-k10 Driver is integrated into the kernel. Available in the EMC-approved section of the QLogic website.http://www.qlogic.com65. Supported kernels: 2.6.32-220.el6, 2.6.32-220.2.1.el6, 2.6.32-220.4.1.el6, 2.6.32-220.4.2.el6, 2.6.32-220.7.1.el6, 2.6.32-220.13.1.el6, 2.6.32-220.17.1.el6. Confirm kernel support

with server vendor.66. RHEL KVM is supported but not with EMC PowerPath. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.67. BIOS 7.2.1 Driver can be downloaded from support.dell.com68. Driver Version 2.7.2.1k Driver can be downloaded from support.dell.com69. Supported kernels: 2.6.9-78.EL, 2.6.9-78.0.1.EL, 2.6.9-78.0.5.EL, 2.6.9-78.0.8.EL, 2.6.9-78.0.13.EL, 2.6.9-78.0.17.EL, 2.6.9-78.0.22.EL, 2.6.9-78.0.24, 2.6.9-78.0.31.EL,

2.6.9-78.0.32.EL, 2.6.9-78.0.33.EL. Confirm kernel support with server vendor.70. Supported kernels: 2.6.18-92.el5, 2.6.18-92.1.1.el5, 2.6.18-92.1.6.el5, 2.6.18-92.1.10.el5, 2.6.18-92.1.13.el5, 2.6.18-92.1.17.el5, 2.6.18-92.1.18.el5,2.6.18-92.1.22.el5,

2.6.18-92.1.24.el5, 2.6.18-92.1.26.el5. Confirm kernel support with server vendor.71. Supported kernels: 2.6.18-53.el5, 2.6.18-53.1.4.el5, 2.6.18-53.1.6.el5, 2.6.18-53.1.13.el5, 2.6.18-53.1.14.el5, 2.6.18-53.1.19.el5, 2.6.18-53.1.21.el5. Confirm kernel support with

server vendor.72. Supported kernels: 2.6.18-8.EL5, 2.6.18-8.1.1.EL5, 2.6.18-8.1.3.EL5, 2.6.18-8.1.4.EL5, 2.6.18-8.1.6.EL5, 2.6.18-8.1.8.EL5, 2.6.18-8.1.10.EL5, 2.6.18-8.1.14.EL5, and

2.6.18-8.1.15.el5. Confirm kernel support with server vendor.73. Supported kernels: 2.6.9-67.EL, 2.6.9-67.0.1.EL, 2.6.9-67.0.4.EL, 2.6.9-67.0.7.EL, 2.6.9-67.0.15.EL, 2.6.9-67.0.20.EL, 2.6.9-67.0.22.EL. Confirm kernel support with server vendor.74. Driver Version 3.27 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com75. PowerPath 4.3.4 or higher is supported - please check support of PowerPath on the base Operating System76. Host CLI iSCSI LUN Snap and Replication is supported in NAS 5.5.27 or higher77. In accordance with the Red Hat Enterprise Linux Errata Support Policy, the regular 7 year life-cycle of Red Hat Enterprise Linux 3 will end on October 31, 2010. All RHEL 3

configurations in the ESM will be frozen as of the publication of the October 2010 ESM. At this time, Red Hat Enterprise Linux 3 will no longer be publicly supported and will requirean extended support contract from Red Hat in order for the RHEL 3 configuration in the ESM to be supported by EMC.

78. Supported kernels: 2.4.21-50.EL, 2.4.21-51.EL, 2.4.21-52.EL, 2.4.21-53.EL, 2.4.21-57.EL, 2.4.21-58.EL, 2.4.21-63.EL, 2.4.21-66.EL. Confirm kernel support with server vendor.79. Driver Version iSCSI initiator 3.6.3 Driver is integrated into the kernel. The following NICs are not supported: 3COM-3C996B80. Driver Version iSCSI initiator 3.6.3 Driver is integrated into the kernel.81. Supported kernels: 2.4.21-47.EL, 2.4.21-47.0.1.EL. Confirm support with server vendor.82. Supported kernels: 2.6.9-55.EL, 2.6.9-55.0.2.EL., 2.6.9-55.0.6.EL, 2.6.9-55.0.9.EL, 2.6.9-55.0.12.EL, 2.6.9-55.0.14.EL. Confirm kernel support with server vendor.83. Driver Version 3.22 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com84. Supported kernels: 2.4.21-40.EL. Confirm kernel support with server vendor.85. Driver Version 3.23 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com86.

Storage Array


Driver Version iSCSI initiator 4.0.1.11 The following NICs are not supported: 3COM-3C996B The software initiator is part of the operating system and not an EMC software product.Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The DocumentLibrary -> Host Connectivity for the complete installation information.

87. Supported kernels: 2.6.9-42.EL, 2.6.9-42.0.2.EL, 2.6.9-42.0.3.EL, 2.6.9-42.0.8.EL, 2.6.9-42.0.10.EL. Confirm kernel support with server vendor.88. Driver Version iSCSI initiator 4.0.1.11 The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux

iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installationinformation.

89. Driver Version 5.00.04 Driver is integrated into the kernel. Available in the EMC-approved section of the QLogic website.http://www.qlogic.com90. Supported kernels: 2.6.9-34.EL, 2.6.9-34.0.1.EL, 2.6.9-34.0.2.EL. Confirm kernel support with server vendor.91. Driver Version 5.00.07 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com92. Supported kernels: 2.6.9-22.EL, 2.6.9-22.0.1.EL, 2.6.9-22.0.2.EL. Confirm kernel support with server vendor.93. Driver Version 3.2794. Driver Version 5.02.04.02.05.08-d0 Driver is integrated into the kernel.95. Supported kernels:2.6.18-308.el5, 2.6.18-308.1.1.el5, 2.6.18-308.4.1.el5. Confirm kernel support with server vendor.96. iSCSI Boot from SAN is supported on certain IBM Servers BladeCenter models. Contact IBM support to obtain a list of supported blades and Microsoft








103. Virtual machines running on VMWare ESX are supported booting from the array.104. Intel iSCSI boot is supported on Dell servers with the following adapters: PRO/1000 PF, PRO/1000 PT, PRO/1000 PT dual port, PRO/ 1000 VT quad port, Ethernet X520 10GbE

Dual Port KX4 and Ethernet Server Adapter X520-2 10GbE Please visithttp://support.dell.com for the most currently supported servers and firmware/driver revisions.105. iSCSI Boot is supported with on Cisco UCS B-Series blades using the M81KR106. Broadcom iSCSI Boot is supported with the following adapters: Broadcom 5708, 5709, 5722, 57710 and 57711

iSCSI boot is supported with Windows 2003 , Windows 2008 and Windows 2008 R2Please visit http://support.dell.com for the currently supported servers, firmware/driver versions and special install instructions.

107. Driver Version 4.1.239 Driver is integrated into the kernel.108. Driver Version 2.0.527.0 Driver is integrated into the kernel.

Red Hat RHEL [AMD-64]Red Hat

Red Hat



StorageOperative

EnvironmentExternal

Boot Comments

1 Red Hat RHEL[AMD-64] 3.0 U7AS/ES7, 8, 9



1.1 N See3


QLogic QLA4010-E-SP17, QLogic QLA4010-E-SP5,QLogic QLA4010C-E-SP17, QLogicQLA4010C-E-SP5, QLogic QLA4050-E-SP1, 2, 5,QLogic QLA4050C-E-SP1, 2, 5, QLogicQLA4052C-E-SP1, 2, 5


1.1 Y See3, 4


QLogic QLA4050-E-SP1, 2, 13, QLogicQLA4050C-E-SP1, 2, 13, QLogic QLA4052C-E-SP1, 2,13


1.1 Y See3, 4

4 Red Hat RHEL[AMD-64] 3.9 AS/ES7,9, 14

QLogic QLA4010-E-SP1, 2, 15, QLogicQLA4010C-E-SP1, 2, 15


1.1 N See3

5 Red Hat RHEL[AMD-64] 3.9 AS/ES7,9, 14

QLogic QLA4010-E-SP1, 2, 15, QLogicQLA4010C-E-SP1, 2, 15, QLogic QLA4050-E-SP1, 2,15, QLogic QLA4050C-E-SP1, 2, 15, QLogicQLA4052C-E-SP1, 2, 15


1.1 Y See3, 4

6 Red Hat RHEL[AMD-64]: 3.0 U8AS/ES7, 9, 12, 3.9AS/ES7, 9, 14



1.1 N See3

1. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.2. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com3. PowerPath 4.3.4 or higher is supported - please check support of PowerPath on the base Operating System4. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.5. Driver Version 3.23 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com6. Routed networks (layer 3) require iSCSI digest to be enabled.7. Host CLI iSCSI LUN Snap and Replication is supported in NAS 5.5.27 or higher8. Supported kernels: 2.4.21-40.EL. Confirm kernel support with server vendor.9. In accordance with the Red Hat Enterprise Linux Errata Support Policy, the regular 7 year life-cycle of Red Hat Enterprise Linux 3 will end on October 31, 2010. All RHEL 3


10. Driver Version iSCSI initiator 3.6.3 Driver is integrated into the kernel. The following NICs are not supported: 3COM-3C996B11. Driver Version iSCSI initiator 3.6.3 Driver is integrated into the kernel.12. Supported kernels: 2.4.21-47.EL, 2.4.21-47.0.1.EL. Confirm support with server vendor.13. Driver Version 3.2714. Supported kernels: 2.4.21-50.EL, 2.4.21-51.EL, 2.4.21-52.EL, 2.4.21-53.EL, 2.4.21-57.EL, 2.4.21-58.EL, 2.4.21-63.EL, 2.4.21-66.EL. Confirm kernel support with server vendor.15. Driver Version 3.27 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com16. NIC teaming with the Linux software initiator is not supported.17. Driver Version 3.22 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com

Red Hat RHEL [EM64T]Red Hat

Storage Array


Red Hat



StorageOperative

EnvironmentExternal

Boot Comments

1 Red Hat RHEL[EM64T] 3.0 U7AS/ES4, 12, 15



1.1 N See2


QLogic QLA4010-E-SP14, QLogic QLA4010-E-SP16,QLogic QLA4010C-E-SP14, QLogic QLA4010C-E-SP16,QLogic QLA4050-E-SP6, 7, 16, QLogicQLA4050C-E-SP6, 7, 16, QLogic QLA4052C-E-SP6, 7, 16


1.1 Y See2, 3


QLogic QLA4050-E-SP6, 7, 17, QLogicQLA4050C-E-SP6, 7, 17, QLogic QLA4052C-E-SP6, 7, 17


1.1 Y See2, 3

4 Red Hat RHEL[EM64T] 3.9 AS/ES4,5

QLogic QLA4010-E-SP6, 7, 8, QLogicQLA4010C-E-SP6, 7, 8


1.1 N See2

5 Red Hat RHEL[EM64T] 3.9 AS/ES4,5

QLogic QLA4010-E-SP6, 7, 8, QLogicQLA4010C-E-SP6, 7, 8, QLogic QLA4050-E-SP6, 7, 8,QLogic QLA4050C-E-SP6, 7, 8, QLogicQLA4052C-E-SP6, 7, 8


1.1 Y See2, 3

6 Red Hat RHEL[EM64T]: 3.0 U8AS/ES4, 12, 13, 3.9AS/ES4, 5



1.1 N See2

1. Routed networks (layer 3) require iSCSI digest to be enabled.2. PowerPath 4.3.4 or higher is supported - please check support of PowerPath on the base Operating System3. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.4. In accordance with the Red Hat Enterprise Linux Errata Support Policy, the regular 7 year life-cycle of Red Hat Enterprise Linux 3 will end on October 31, 2010. All RHEL 3


5. Supported kernels: 2.4.21-50.EL, 2.4.21-51.EL, 2.4.21-52.EL, 2.4.21-53.EL, 2.4.21-57.EL, 2.4.21-58.EL, 2.4.21-63.EL, 2.4.21-66.EL. Confirm kernel support with server vendor.6. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.7. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com8. Driver Version 3.27 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com9. Driver Version iSCSI initiator 3.6.3 Driver is integrated into the kernel. The following NICs are not supported: 3COM-3C996B

10. NIC teaming with the Linux software initiator is not supported.11. Driver Version iSCSI initiator 3.6.3 Driver is integrated into the kernel.12. Host CLI iSCSI LUN Snap and Replication is supported in NAS 5.5.27 or higher13. Supported kernels: 2.4.21-47.EL, 2.4.21-47.0.1.EL. Confirm support with server vendor.14. Driver Version 3.22 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com15. Supported kernels: 2.4.21-40.EL. Confirm kernel support with server vendor.16. Driver Version 3.23 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com17. Driver Version 3.27

Red Hat RHEL [IA64]Red Hat

Red Hat



EnvironmentExternal

Boot

1 Red Hat RHEL [IA64]: 4.8AS/ES8, 5.32, 3, 5.42, 7

Generic Vendor NIC 10/1004, 9,Generic Vendor NIC GbE1, 4

LAN Only5, 6 EMC Unified StorageVNXe3300 (File/iSCSI)

1.1 N



2.6.18-128.7.1.el5, 2.6.18-128.17.1.el5, 2.6.18-128.23.1.el5, 2.6.18-128.23.2.el5, 2.6.18-128.26.1.el5. Confirm kernel support with server vendor.4. NIC teaming with the Linux software initiator is not supported.5. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.6. Routed networks (layer 3) require iSCSI digest to be enabled.7. Supported kernels: 2.6.18-164.el5, 2.6.18-164.2.1.el5, 2.6.18-164.6.1.el5, 2.6.18-164.9.1.el5, 2.6.18-164.10.1.el5, 2.6.18-164.11.1.el5, 2.6.18-164.15.1.el5, 2.6.18-164.17.1.el5,

2.6.18-164.25.1.el5, 2.6.18-164.25.2.el5. Confirm kernel support with server vendor.8. Supported kernels: 2.6.9-89.EL, 2.6.9-89.0.3.EL, 2.6.9-89.0.7.EL, 2.6.9-89.0.9EL, 2.6.9-89.0.11.EL, 2.6.9-89.0.15.EL, 2.6.9-89.0.16.EL, 2.6.9-89.0.18.EL, 2.6.9-89.0.19.EL,

2.6.9-89.0.20.EL, 2.6.9-89.0.23.EL, 2.6.9-89.0.25.EL, 2.6.9-89.0.26.EL, 2.6.9-89.0.28.EL, 2.6.9-89.0.29.EL, 2.6.9-89.29.1.EL, 2.6.9-89.31.1.EL, 2.6.9-89.33.1.EL, 2.6.9-89.35.1.EL.Confirm kernel support with server vendor.


Red Hat RHEL [x86_64]Red Hat

Red Hat

No.Operating



StorageOperative

EnvironmentExternal

Boot Comments

1 Red Hat RHEL[x86_64] 4.0 U4AS/ES1, 95

QLogic QLA4050-E-SP3, 4, 7, 97, QLogic QLA4050-E-SP3,4, 97, QLogic QLA4050C-E-SP3, 4, 7, 97, QLogicQLA4050C-E-SP3, 4, 97, QLogic QLA4052C-E-SP3, 4, 7, 97,QLogic QLA4052C-E-SP3, 4, 97


1.1 Y See5, 6

2 Red Hat RHEL[x86_64] 4.0: U2AS/ES1, 2, U3AS/ES1, 96

QLogic QLA4050-E-SP3, 4, 7, QLogic QLA4050C-E-SP3, 4,7, QLogic QLA4052C-E-SP3, 4, 7


1.1 Y See5, 6

3 Red Hat RHEL[x86_64] 4.0: U2AS/ES1, 2, U3AS/ES1, 96, U4AS/ES1, 95

Generic Vendor NIC 10/10010, Generic Vendor NIC GbE9 LAN Only6, 8 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

Storage Array


4 Red Hat RHEL[x86_64] 5.569, 70



Y24, 32, 34 See39, 41

5 Red Hat RHEL[x86_64] 5.569, 70

Generic Vendor NIC 10GbE44, 52, 53, 55, 87 LAN Only8 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y23, 24, 32,34

See39

6 Red Hat RHEL[x86_64] 5.569, 70

Generic Vendor NIC GbE44, 52, 53, 54, 87 LAN Only8 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y24, 32 See39

7 Red Hat RHEL[x86_64] 5.619, 74



Y24, 32, 34 See39, 41

8 Red Hat RHEL[x86_64] 5.619, 74



Y24 See39, 40,41

9 Red Hat RHEL[x86_64] 5.619, 74

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HPc-Class BladeSystem (488074-B21)58, 59, 60, 78


Y24, 32 See39

10 Red Hat RHEL[x86_64] 5.619, 74

QLogic QLA4010-E-SP3, 4, 65, 66, 78, QLogicQLA4010C-E-SP3, 4, 65, 66, 78, QLogic QLA4050-E-SP3, 4,59, 62, 63, 78, QLogic QLA4050C-E-SP3, 4, 59, 62, 63, 78,QLogic QLA4052C-E-SP3, 4, 59, 62, 63, 78, QLogicQLE4060C-E-SP4, 58, 59, 63, 68, 78, QLogicQLE4062C-E-SP4, 58, 59, 63, 68, 78


Y32 See39

11 Red Hat RHEL[x86_64] 5.619, 74



N

12 Red Hat RHEL[x86_64] 5.719, 72



Y24, 32, 34 See39, 41

13 Red Hat RHEL[x86_64] 5.719, 72



Y24 See39, 40,41

14 Red Hat RHEL[x86_64] 5.719, 72



Y24, 32 See39

15 Red Hat RHEL[x86_64] 5.719, 72



Y32 See39

16 Red Hat RHEL[x86_64] 5.719, 72



N

17 Red Hat RHEL[x86_64] 5.818, 19

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT)rNDC (rack)48, 50, 51, Broadcom Broadcom 57810 DP 10GbDA/SFP+ CNA48, 50, 51, Dell Broadcom 57810 Dual Port10GbE KR Blade Converged Mezz48, 51, 64, EmulexOCe11102-IM-E35, 36, 37, 38, Emulex OCe11102-IX-E35, 36,37, 38


Y20, 21, 22,23, 24, 25, 26,27, 28, 29, 30,31, 32, 33, 34

See39, 40,41

18 Red Hat RHEL[x86_64] 5.818, 19

Emulex OCe10102-IM-E36, 56, 57, EmulexOCe10102-IX-E36, 56, 57, IBM IBM Broadcom 10GbE 2-PortEthernet Expansion Card for IBM BladeCenter(46M6168)42, 43, 44, 47, 48, 49, IBM IBM Broadcom 10GbE4-Port Ethernet Expansion Card for IBM BladeCenter(46M6164)42, 43, 44, 47, 48, 49


Y20, 21, 22,23, 24, 25, 26,27, 28, 29, 30,31, 32, 33, 34

See39, 41

19 Red Hat RHEL[x86_64] 5.818, 19

Generic Vendor NIC 10/10052, Generic Vendor NIC10GbE44, 52, 53, 55, Generic Vendor NIC GbE44, 52, 53, 54,Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HPc-Class BladeSystem (488074-B21)58, 59, 60, 67, QLogicQLA4010-E-SP3, 4, 65, 66, 67, QLogic QLA4010C-E-SP3, 4,65, 66, 67, QLogic QLA4050-E-SP3, 4, 59, 62, 63, 67, QLogicQLA4050C-E-SP3, 4, 59, 62, 63, 67, QLogicQLA4052C-E-SP3, 4, 59, 62, 63, 67, QLogicQLE4060C-E-SP4, 58, 59, 63, 67, 68, QLogicQLE4062C-E-SP4, 58, 59, 63, 67, 68


Y20, 21, 22,23, 24, 25, 26,27, 28, 29, 30,31, 32, 33, 34

See39

Storage Array


20 Red Hat RHEL[x86_64] 5.818, 19



Y20, 21, 22,23, 24, 25, 26,27, 28, 29, 30,31, 32, 33, 34

21 Red Hat RHEL[x86_64] 6.114, 15,16, 17



Y24, 32 See39

22 Red Hat RHEL[x86_64] 6.114, 15,16, 17



Y32 See39

23 Red Hat RHEL[x86_64] 6.215, 16,17, 45, 46



Y24, 32 See39

24 Red Hat RHEL[x86_64] 6.215, 16,17, 45, 46



Y32 See39

25 Red Hat RHEL[x86_64] 6.215, 16,17, 45, 46

QLogic QLE8240-SR-E-SP11, 12, 61, QLogicQLE8250-CU-E-SP11, 12, 61, QLogic QLE8252-CU-E-SP11,12, 61


N

26 Red Hat RHEL[x86_64]: 4.5AS/ES1, 94, 4.6AS/ES93, 4.7AS/ES88, 4.8AS/ES81, 5.383,84, 5.483, 85



1.1 N

27 Red Hat RHEL[x86_64]: 5.083, 92,5.183, 91, 5.216, 83,89

Generic Vendor NIC 10/10044, 52, Generic Vendor NICGbE90


1.1 N

28 Red Hat RHEL[x86_64]: 5.569, 70,5.619, 74, 5.719, 72,6.015, 16, 17, 79,6.114, 15, 16, 17,6.215, 16, 17, 45, 46

Generic Vendor NIC 10/10052 LAN Only8 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y24, 32 See39

29 Red Hat RHEL[x86_64]: 5.569, 70,5.619, 74, 5.719, 72,6.015, 16, 17, 79,6.114, 15, 16, 17,6.215, 16, 17, 45, 46

IBM IBM Broadcom 10GbE 2-Port Ethernet Expansion Cardfor IBM BladeCenter (46M6168)42, 43, 44, 47, 48, 49, IBM IBMBroadcom 10GbE 4-Port Ethernet Expansion Card for IBMBladeCenter (46M6164)42, 43, 44, 47, 48, 49


Y24 See39, 41

30 Red Hat RHEL[x86_64]: 5.569, 70,6.015, 16, 17, 79



Y24, 32 See39

31 Red Hat RHEL[x86_64]: 5.569, 70,6.015, 16, 17, 79



Y32 See39

32 Red Hat RHEL[x86_64]: 5.619, 74,5.719, 72, 6.015, 16,17, 79, 6.114, 15, 16,17, 6.215, 16, 17, 45,46


Y23, 24, 32,34

See39

33 Red Hat RHEL[x86_64]: 5.619, 74,5.719, 72, 6.015, 16,17, 79, 6.114, 15, 16,17, 6.215, 16, 17, 45,46

Generic Vendor NIC GbE44, 52, 53, 54 LAN Only8 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y24, 32 See39

34 Red Hat RHEL[x86_64]: 6.015, 16,17, 79, 6.114, 15, 16,17

QLogic QLE8240-SR-E-SP11, 12, 13, QLogicQLE8250-CU-E-SP11, 12, 13, QLogic QLE8252-CU-E-SP11,12, 13


N

35 Red Hat RHEL[x86_64]: 6.015, 16,17, 79, 6.114, 15, 16,17, 6.215, 16, 17, 45,46

QLogic QLE8242-SR-E-SP11, 12, 13 LAN Only8 EMC UnifiedStorageVNXe3300(File/iSCSI)

N

36 Red Hat RHEL[x86_64]: 6.114, 15,16, 17, 6.215, 16, 17,45, 46

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT)rNDC (rack)48, 50, 51, Broadcom Broadcom 57810 DP 10GbDA/SFP+ CNA48, 50, 51, Dell Broadcom 57810 Dual Port10GbE KR Blade Converged Mezz48, 50, 51


N

37 Red Hat RHEL[x86_64]: 6.114, 15,16, 17, 6.215, 16, 17,45, 46

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT)rNDC (rack)48, 50, 51, Broadcom Broadcom 57810 DP 10GbDA/SFP+ CNA48, 50, 51, Dell Broadcom 57810 Dual Port10GbE KR Blade Converged Mezz48, 50, 51


Y23, 24, 32,34

See39, 41

1. Host CLI iSCSI LUN Snap and Replication is supported in NAS 5.5.27 or higher2. Supported kernels: 2.6.9-22.EL, 2.6.9-22.0.1.EL, 2.6.9-22.0.2.EL. Confirm kernel support with server vendor.3. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.4. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com5. PowerPath 4.3.4 or higher is supported - please check support of PowerPath on the base Operating System6. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.7. Driver Version 5.00.04 Driver is integrated into the kernel. Available in the EMC-approved section of the QLogic website.http://www.qlogic.com

Storage Array


8. Routed networks (layer 3) require iSCSI digest to be enabled.9. Driver Version iSCSI initiator 4.0.1.11 The following NICs are not supported: 3COM-3C996B The software initiator is part of the operating system and not an EMC software product.

Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The DocumentLibrary -> Host Connectivity for the complete installation information.

10. Driver Version iSCSI initiator 4.0.1.11 The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC LinuxiSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installationinformation.

11. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com12. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com13. Driver Version 5.02.11.00.05.06-c3 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com14. Supported kernels: 2.6.32-131.0.15.el6, 2.6.32-131.2.1.el6, 2.6.32-131.6.1.el6, 2.6.32-131.12.1.el6, 2.6.32-131.17.1.el6, 2.6.32-131.21.1.el6, 2.6.32-131.25.1.el6. Confirm kernel

support with server vendor.15. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.16. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.17. EMC supports the following filesystems: ext2, ext3, ext4, xfs, gfs, and gfs2 unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please

submit an RPQ.18. Supported kernels:2.6.18-308.el5, 2.6.18-308.1.1.el5, 2.6.18-308.4.1.el5. Confirm kernel support with server vendor.19. EMC supports the following filesystems: ext2, ext3, ext4, xfs, and gfs unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please submit

an RPQ.20. iSCSI Boot from SAN is supported on certain IBM Servers BladeCenter models. Contact IBM support to obtain a list of supported blades and Microsoft















35. Firmware Version 3.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com36. Driver Version 4.1.239 Driver is integrated into the kernel.37. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com38. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com39. Please refer to the Host Bus Adapter note for the supported NICs.40. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.41. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.42. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php43. Broadcom iSCSI offload (without iboot) is supported with following adapters:


44. NIC teaming with the Linux software initiator is not supported.45. Supported kernels: 2.6.32-220.el6, 2.6.32-220.2.1.el6, 2.6.32-220.4.1.el6, 2.6.32-220.4.2.el6, 2.6.32-220.7.1.el6, 2.6.32-220.13.1.el6, 2.6.32-220.17.1.el6. Confirm kernel support

with server vendor.46. RHEL KVM is supported but not with EMC PowerPath. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.47. BIOS 5.0.1148. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.49. Firmware Version 2.1.1a50. BIOS 7.2.1 Driver can be downloaded from support.dell.com51. Driver Version 2.7.2.1k Driver can be downloaded from support.dell.com52. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux




55. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.56. Firmware Version 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com57. BIOS 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com58. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com59. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com60. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com61. Driver Version 5.02.00.00.06.02-k10 Driver is integrated into the kernel. Available in the EMC-approved section of the QLogic website.http://www.qlogic.com62. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com63. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com64. BIOS 7.2.165. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com66. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com67. Driver Version 5.02.04.02.05.08-d0 Driver is integrated into the kernel.68. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.69. EMC supports the following filesystems: ext2, ext3, xfs, and gfs unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please submit an

RPQ.70. Supported kernels: 2.6.18-194.el5, 2.6.18-194.3.1.el5, 2.6.18-194.8.1.el5, 2.6.18-194.11.1.el5, 2.6.18-194.11.3.el5, 2.6.18-194.11.4.el5, 2.6.18-194.17.1.el5, 2.6.18-194.17.4.el5,

2.6.18-194.26.1.el5, 2.6.18-194.32.1.el5 Confirm kernel support with server vendor.71. Driver Version 2.0.527.0 Driver is integrated into the kernel.72. Supported kernels: 2.6.18-274.el5, 2.6.18-274.3.1el5, 2.6.18-274.7.1.el5, 2.6.18-274.12.1.el5, 2.6.18-274.17.1.el5, 2.6.18-274.18.1.el5. Confirm kernel support with server vendor.73. Driver Version 4.0.100r Driver is integrated into the kernel.74. Supported kernels: 2.6.18-238.el5, 2.6.18-238.1.1.el5, 2.6.18-238.5.1.el5, 2.6.18-238.9.1.el5, 2.6.18-238.12.1.el5, 2.6.18-238.19.1.el5, 2.6.18-238.21.1.el5, 2.6.18-238.27.1.el5,

2.6.18-238.28.1.el5, 2.6.18-238.31.1.el5, 2.6.18-238.33.1.el5, 2.6.18-238.35.1.el5, 2.6.18-238.37.1.el5. Confirm kernel support with server vendor.75. Driver Version 2.0.549.0 Driver is integrated into the kernel.

Storage Array


76. Driver Version 5.02.00-k5 Driver is integrated into the kernel.77. Driver Version 5.02.04.01.05.07-d0 Driver is integrated into the kernel.78. Driver Version 5.02.04.02.05.06-d0 Driver is integrated into the kernel.79. Supported kernels: 2.6.32-71.el6, 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6, 2.6.32-71.24.1.el6, 2.6.32-71.31.1.el6, 2.6.32-71.34.1.el6,

2.6.32-71.36.1.el6, 2.6.32-71.37.1.el6, 2.6.32-71.38.1.el6. Confirm kernel support with server vendor.80. Driver Version 5.01.00.01.05.04-k9 Driver is integrated into the kernel.81. Supported kernels: 2.6.9-89.EL, 2.6.9-89.0.3.EL, 2.6.9-89.0.7.EL, 2.6.9-89.0.9EL, 2.6.9-89.0.11.EL, 2.6.9-89.0.15.EL, 2.6.9-89.0.16.EL, 2.6.9-89.0.18.EL, 2.6.9-89.0.19.EL,

2.6.9-89.0.20.EL, 2.6.9-89.0.23.EL, 2.6.9-89.0.25.EL, 2.6.9-89.0.26.EL, 2.6.9-89.0.28.EL, 2.6.9-89.0.29.EL, 2.6.9-89.29.1.EL, 2.6.9-89.31.1.EL, 2.6.9-89.33.1.EL, 2.6.9-89.35.1.EL.Confirm kernel support with server vendor.



2.6.18-128.7.1.el5, 2.6.18-128.17.1.el5, 2.6.18-128.23.1.el5, 2.6.18-128.23.2.el5, 2.6.18-128.26.1.el5. Confirm kernel support with server vendor.85. Supported kernels: 2.6.18-164.el5, 2.6.18-164.2.1.el5, 2.6.18-164.6.1.el5, 2.6.18-164.9.1.el5, 2.6.18-164.10.1.el5, 2.6.18-164.11.1.el5, 2.6.18-164.15.1.el5, 2.6.18-164.17.1.el5,

2.6.18-164.25.1.el5, 2.6.18-164.25.2.el5. Confirm kernel support with server vendor.86. Driver Version iSCSI initiator 4.0.1.11 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please refer to the

required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> HostConnectivity for the complete installation information.

87. The Emerson ATCA-7365 server blade and the Centellis 4440 ATCA Shelf/ATCA-F120 are supported with either 1GB or 10GB iSCSI. Please contact Emerson for specificconfigurations.

88. Supported kernels: 2.6.9-78.EL, 2.6.9-78.0.1.EL, 2.6.9-78.0.5.EL, 2.6.9-78.0.8.EL, 2.6.9-78.0.13.EL, 2.6.9-78.0.17.EL, 2.6.9-78.0.22.EL, 2.6.9-78.0.24, 2.6.9-78.0.31.EL,2.6.9-78.0.32.EL, 2.6.9-78.0.33.EL. Confirm kernel support with server vendor.

89. Supported kernels: 2.6.18-92.el5, 2.6.18-92.1.1.el5, 2.6.18-92.1.6.el5, 2.6.18-92.1.10.el5, 2.6.18-92.1.13.el5, 2.6.18-92.1.17.el5, 2.6.18-92.1.18.el5,2.6.18-92.1.22.el5,2.6.18-92.1.24.el5, 2.6.18-92.1.26.el5. Confirm kernel support with server vendor.

90. Driver Version iSCSI Software Initiator 1.0-595 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please referto the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> HostConnectivity for the complete installation information.

91. Supported kernels: 2.6.18-53.el5, 2.6.18-53.1.4.el5, 2.6.18-53.1.6.el5, 2.6.18-53.1.13.el5, 2.6.18-53.1.14.el5, 2.6.18-53.1.19.el5, 2.6.18-53.1.21.el5. Confirm kernel support withserver vendor.

92. Supported kernels: 2.6.18-8.EL5, 2.6.18-8.1.1.EL5, 2.6.18-8.1.3.EL5, 2.6.18-8.1.4.EL5, 2.6.18-8.1.6.EL5, 2.6.18-8.1.8.EL5, 2.6.18-8.1.10.EL5, 2.6.18-8.1.14.EL5, and2.6.18-8.1.15.el5. Confirm kernel support with server vendor.

93. Supported kernels: 2.6.9-67.EL, 2.6.9-67.0.1.EL, 2.6.9-67.0.4.EL, 2.6.9-67.0.7.EL, 2.6.9-67.0.15.EL, 2.6.9-67.0.20.EL, 2.6.9-67.0.22.EL. Confirm kernel support with server vendor.94. Supported kernels: 2.6.9-55.EL, 2.6.9-55.0.2.EL., 2.6.9-55.0.6.EL, 2.6.9-55.0.9.EL, 2.6.9-55.0.12.EL, 2.6.9-55.0.14.EL. Confirm kernel support with server vendor.95. Supported kernels: 2.6.9-42.EL, 2.6.9-42.0.2.EL, 2.6.9-42.0.3.EL, 2.6.9-42.0.8.EL, 2.6.9-42.0.10.EL. Confirm kernel support with server vendor.96. Supported kernels: 2.6.9-34.EL, 2.6.9-34.0.1.EL, 2.6.9-34.0.2.EL. Confirm kernel support with server vendor.97. Driver Version 5.00.07 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com


Red Hat

No.Operating



Boot Comments

1 Red Hat RHEL[x86_84] 6.31,2, 3, 4

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT) rNDC (rack)13, 19, 20,Broadcom Broadcom 57810 DP 10Gb DA/SFP+ CNA13, 19, 20, Dell Broadcom57810 Dual Port 10GbE KR Blade Converged Mezz13, 19, 20


Y8, 16, 17,18

See10, 11

2 Red Hat RHEL[x86_84] 6.31,2, 3, 4

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT) rNDC (rack)13, 19, 20,Broadcom Broadcom 57810 DP 10Gb DA/SFP+ CNA13, 19, 20, Dell Broadcom57810 Dual Port 10GbE KR Blade Converged Mezz13, 19, 20, QLogicQLE8240-SR-E-SP24, 28, 29, QLogic QLE8242-SR-E-SP24, 28, 29, QLogicQLE8250-CU-E-SP24, 28, 29, QLogic QLE8252-CU-E-SP24, 28, 29


N

3 Red Hat RHEL[x86_84] 6.31,2, 3, 4



Y8, 16 See10

4 Red Hat RHEL[x86_84] 6.31,2, 3, 4

Generic Vendor NIC 10GbE7, 15, 21, 23 LAN Only9 EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

Y8, 16, 17,18

See10

5 Red Hat RHEL[x86_84] 6.31,2, 3, 4



Y8 See10, 11

6 Red Hat RHEL[x86_84] 6.31,2, 3, 4

QLogic QLA4010-E-SP24, 30, 31, 34, 35, QLogic QLA4010C-E-SP24, 30, 31, 34,35, QLogic QLA4050-E-SP24, 25, 30, 31, 32, 33, QLogic QLA4050C-E-SP24, 25,30, 31, 32, 33, QLogic QLA4052C-E-SP24, 25, 30, 31, 32, 33, QLogicQLE4060C-E-SP24, 25, 27, 31, 32, 36, 37, QLogic QLE4062C-E-SP24, 25, 27, 31,32, 36


Y16 See10


Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.3. Supported kernels: 2.6.32-279.el6. Confirm kernel support with server vendor.4. EMC supports the following filesystems: ext2, ext3, ext4, xfs, gfs, and gfs2 unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please

submit an RPQ.5. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php6. Broadcom iSCSI offload (without iboot) is supported with following adapters:


7. NIC teaming with the Linux software initiator is not supported.8. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168


9. Routed networks (layer 3) require iSCSI digest to be enabled.10. Please refer to the Host Bus Adapter note for the supported NICs.11. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.12. Firmware Version 2.1.1a13. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.14. BIOS 5.0.1115. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.16. Broadcom iSCSI boot is supported with following adapters:



Storage Array



19. BIOS 7.2.1 Driver can be downloaded from support.dell.com20. Driver Version 2.7.2.1k Driver can be downloaded from support.dell.com21. Broadcom iSCSI offload (without iboot) is supported with following adapters:



23. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.24. Driver Version 5.02.00.00.06.03-k4 Driver is integrated into the kernel.25. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com26. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com27. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com28. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com29. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com30. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.31. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com32. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com33. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com34. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com35. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com36. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.37. Driver Version 5.02.00-k5 Driver is integrated into the kernel.

SuSE SLES [32-Bit]SuSE

SuSE

No.Operating



StorageOperative

EnvironmentExternal

Boot Comments

1 SuSE SLES[32-Bit] 10SP153

Generic Vendor NIC 10/10016, 54 LAN Only7, 51 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

2 SuSE SLES[32-Bit] 10SP460, 61, 62,63

QLogic QLE8240-SR-E-SP24, 26, 59, QLogic QLE8242-SR-E-SP24, 26,59, QLogic QLE8250-CU-E-SP24, 26, 59, QLogic QLE8252-CU-E-SP24,26, 59


N

3 SuSE SLES[32-Bit] 10:SP153,SP252;

SuSE SLES[32-Bit]:1069, 1174

Generic Vendor NIC GbE50 LAN Only7, 51 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

4 SuSE SLES[32-Bit] 1069

Generic Vendor NIC 10/10050 LAN Only7, 51 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

5 SuSE SLES[32-Bit] 1069

QLogic QLA4050-E-SP39, 40, 68, QLogic QLA4050C-E-SP39, 40, 68,QLogic QLA4052C-E-SP39, 40, 68


1.1 Y See51, 65

6 SuSE SLES[32-Bit] 11SP18, 9, 10,11, 12, 13

Emulex OCe10102-IM-E27, 28, 41, Emulex OCe10102-IX-E27, 28, 41,Generic Vendor NIC 10GbE16, 29, 31, 32, Hewlett Packard QlogicQMH4062 1GbE iSCSI HBA for HP c-Class BladeSystem(488074-B21)33, 34, 35, 43


Y18

7 SuSE SLES[32-Bit] 11SP18, 9, 10,11, 12, 13

Emulex OCe11102-IM-E20, 22, 23, 48, Emulex OCe11102-IX-E20, 22, 23,48


Y4 See1, 2, 17

8 SuSE SLES[32-Bit] 11SP18, 9, 10,11, 12, 13

Generic Vendor NIC 10/10016, 49, Generic Vendor NIC 10GbE16, 29,31, 32, Generic Vendor NIC GbE16, 49


N See17

9 SuSE SLES[32-Bit] 11SP18, 9, 10,11, 12, 13

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)33, 34, 35, 43, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)40, 43, 46, 47, QLogic QLA4010-E-SP39, 40,43, 44, 45, QLogic QLA4010C-E-SP39, 40, 43, 44, 45, QLogicQLE4060C-E-SP33, 35, 38, 40, 42, 43, QLogic QLE4062C-E-SP33, 35, 38,40, 42, 43


N

10 SuSE SLES[32-Bit] 11SP18, 9, 10,11, 12, 13

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)33, 34, 35, 43, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)40, 43, 46, 47, QLogic QLA4010-E-SP39, 40,43, 44, 45, QLogic QLA4010C-E-SP39, 40, 43, 44, 45, QLogicQLE4060C-E-SP33, 35, 38, 40, 42, 43, QLogic QLE4062C-E-SP33, 35, 38,40, 42, 43, QLogic QLE8240-SR-E-SP24, 25, 26, QLogicQLE8242-SR-E-SP24, 25, 26, QLogic QLE8250-CU-E-SP24, 25, 26,QLogic QLE8252-CU-E-SP24, 25, 26


N

11 SuSE SLES[32-Bit] 11SP18, 9, 10,11, 12, 13



Y4 See1, 2

Storage Array


12 SuSE SLES[32-Bit] 11SP18, 9, 10,11, 12, 13

QLogic QLA4050-E-SP33, 37, 38, 39, 40, 43, QLogic QLA4050-E-SP33,37, 39, 40, 43, QLogic QLA4050C-E-SP33, 37, 38, 39, 40, 43, QLogicQLA4050C-E-SP33, 37, 39, 40, 43, QLogic QLA4052C-E-SP33, 37, 38, 39,40, 43, QLogic QLA4052C-E-SP33, 37, 39, 40, 43, QLogicQLE4060C-E-SP33, 35, 38, 40, 42, 43, QLogic QLE4062C-E-SP33, 35, 38,40, 42, 43


Y

13 SuSE SLES[32-Bit] 11SP28, 9, 10,11, 19

Emulex OCe10102-IM-E21, 27, 28, Emulex OCe10102-IX-E21, 27, 28,Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)33, 34, 35, 36, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)36, 40, 46, 47, QLogic QLA4010-E-SP36, 39,40, 44, 45, QLogic QLA4010C-E-SP36, 39, 40, 44, 45, QLogicQLA4050-E-SP33, 36, 37, 38, 39, 40, QLogic QLA4050-E-SP33, 36, 37, 39,40, QLogic QLA4050C-E-SP33, 36, 37, 38, 39, 40, QLogicQLA4050C-E-SP33, 36, 37, 39, 40, QLogic QLA4052C-E-SP33, 36, 37, 38,39, 40, QLogic QLA4052C-E-SP33, 36, 37, 39, 40, QLogicQLE4060C-E-SP33, 35, 36, 38, 40, 42, QLogic QLE4062C-E-SP33, 35, 36,38, 40, 42


Y4, 18

14 SuSE SLES[32-Bit] 11SP28, 9, 10,11, 19

Emulex OCe10102-IM-E21, 27, 28, Emulex OCe10102-IX-E21, 27, 28,Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)33, 34, 35, 36, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)36, 40, 46, 47, QLogic QLA4010-E-SP36, 39,40, 44, 45, QLogic QLA4010C-E-SP36, 39, 40, 44, 45, QLogicQLA4050-E-SP33, 36, 37, 38, 39, 40, QLogic QLA4050-E-SP33, 36, 37, 39,40, QLogic QLA4050C-E-SP33, 36, 37, 38, 39, 40, QLogicQLA4050C-E-SP33, 36, 37, 39, 40, QLogic QLA4052C-E-SP33, 36, 37, 38,39, 40, QLogic QLA4052C-E-SP33, 36, 37, 39, 40, QLogicQLE4060C-E-SP33, 35, 36, 38, 40, 42, QLogic QLE4062C-E-SP33, 35, 36,38, 40, 42, QLogic QLE8240-SR-E-SP24, 26, 36, QLogicQLE8242-SR-E-SP24, 26, 36, QLogic QLE8250-CU-E-SP24, 26, 36,QLogic QLE8252-CU-E-SP24, 26, 36


Y4, 18

15 SuSE SLES[32-Bit] 11SP28, 9, 10,11, 19



Y4, 18 See1, 2, 17

16 SuSE SLES[32-Bit] 11SP28, 9, 10,11, 19

Generic Vendor NIC 10/10016, 49, Generic Vendor NIC 10GbE16, 29,30, 31, 32, Generic Vendor NIC GbE16, 49


Y4, 18 See17

17 SuSE SLES[32-Bit] 11SP28, 9, 10,11, 19



Y4, 18 See1, 2

18 SuSE SLES[32-Bit] 9SP256, 62, 67,71


1.1 N

19 SuSE SLES[32-Bit] 9SP456, 57



1.1 Y See51, 65

20 SuSE SLES[32-Bit] 9:SP256, 62, 67,71, SP356, 66,67



1.1 Y See51, 65

21 SuSE SLES[32-Bit] 9:SP356, 66, 67,SP456, 57


1.1 N

22 SuSE SLES[32-Bit]: 10SP252, 1174


1.1 N

1. Please refer to the Host Bus Adapter note for the supported NICs.2. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.3. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.4. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168


5. Firmware Version 2.1.1a6. BIOS 5.0.117. Routed networks (layer 3) require iSCSI digest to be enabled.8. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.9. SLES Xen kernel supported. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.

10. EMC supports the following filesystems: ext2, ext3, reiserfs unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please submit an RPQ.11. SGI's XFS filesystem is also supported for this configuration. Files that are part of the released distribution of the operating system (e.g. /, /etc, /usr, /opt, etc) must not reside on an

XFS filesystem. XFS is supported on non-operating system data only.12. Novell OES 11 is supported with this update.13. Supported kernels: 2.6.32.12-0.7, 2.6.32.13-0.4.1, 2.6.32.13-0.5.1, 2.6.32.19-0.2.1, 2.6.32.19-0.3.1, 2.6.32.23-0.3.1, 2.6.32.24-0.2, 2.6.32.27-0.2.2, 2.6.32.29-0.3.1, 2.6.32.36-0.5.2,

2.6.32.43-0.4.1, 2.6.32.45-0.3.2, 2.6.32.46-0.3.1, 2.6.32.49-0.3.1, 2.6.32.54-0.3. Confirm kernel support with server vendor.14. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php15. Broadcom iSCSI offload (without iboot) is supported with following adapters:


16. NIC teaming with the Linux software initiator is not supported.17. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.18. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

iSCSI boot is supported with SUSE SLES 11 SP1Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.

19. Supported kernels:3.0.13-0.27, 3.0.26-0.7. Confirm kernel support with server vendor.20. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com21. Driver Version 4.1.282.0 Driver is integrated into the kernel.22. Firmware Version 3.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com23. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com24. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com25. Driver Version 5.02.11.00.05.06-c3 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com26. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com27. Firmware Version 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com28. BIOS 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com29.

Storage Array


Driver Version 1.3.30-k2 In-kernel driver version supported with Cisco UCS mezzanine adapter. The software initiator is part of the operating system and not an EMC softwareproduct. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> TheDocument Library -> Host Connectivity for the complete installation information.

30. Driver Version iSCSI Software Initiator 2.x Driver is integrated into the kernel.31. EMC Celerra supported for Cisco UCS attach.32. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.33. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com34. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com35. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com36. Driver Version 5.02.00.00.11.2-k2 Driver is integrated into the kernel.37. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com38. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com39. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.40. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com41. Driver Version 2.0.527.0 Driver is integrated into the kernel.42. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.43. Driver Version 5.01.00.00.11.01-k14 Driver is integrated into the kernel.44. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com45. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com46. BIOS 1.09a Available in the EMC-approved section of the QLogic website.http://www.qlogic.com47. Firmware Version 2.00.00.45 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com48. Driver Version 2.103.397.0 Available in the EMC-approved section of the Emulex website.http://www.emulex.com49. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.50. Driver Version iSCSI Software Initiator 1.0-595 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please refer

to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> HostConnectivity for the complete installation information.

51. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.52. Supported kernels: 2.6.16.60-0.21, 2.6.16.60-0.23, 2.6.16.60-0.27, 2.6.16.60-0.30, 2.6.16.60-0.31, 2.6.16.60-0.33, 2.6.16.60-0.34, 2.6.16.60-0.35, 2.6.16.60-0.37, 2.6.16.60-0.39.3,

2.6.16.60-0.42.4, 2.6.16.60-0.42.5, 2.6.16.60-0.42.7, 2.6.16.60-0.42.8, 2.6.16.60-0.42.9, 2.6.16.60-0.42.10, 2.6.16.60-0.42.11. Confirm kernel support with server vendor.53. Supported kernels: 2.6.16.46-0.12, 2.6.16.46-0.14, 2.6.16.53-0.8, 2.6.16.53-0.16, 2.6.16.54-0.2.3, 2.6.16.54-0.2.5, 2.6.16.54-0.2.8. Confirm kernel support with server vendor.54. Driver Version iSCSI Software Initiator 1.0-795 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please refer


55. Driver Version iSCSI initiator 4.0.188.18 Driver is integrated into the kernel. The following NICs are not supported: 3COM-3C996B The software initiator is part of the operatingsystem and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC'sPowerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.

56. In accordance with the SUSE Linux Enterprise Product Support Lifecycle Policy, the regular 7 year life-cycle of SUSE Linux Enterprise Server 9 will end on August 31, 2011. All SLES9 configurations in the ESM will be frozen as of the publication of the August 2011 ESM. At this time, SLES 9 will no longer be publicly supported and will require an extended supportcontract from Novell in order for the SLES 9 configuration in the ESM to be supported by EMC. Extended and Self-Support from Novell is planned to end August 31, 2014.

57. Supported kernels: 2.6.5-7.308, 2.6.5-7.311, 2.6.5-7.312, 2.6.5-7.314, 2.6.5-7.315, 2.6.5-7.316, 2.6.5-7.317, 2.6.5-7.318, 2.6.5-7.319, 2.6.5-7.321, 2.6.5-7.322, 2.6.5-7.323,2.6.5-7.324, 2.6.5-7.325. The 32bit kernel 2.6.5-7.311 is not supported with PowerPath 5.1 SP1. Confirm kernel support with server vendor.


59. Driver Version 5.02.11.00.10.4-d2 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com60. Supported kernels: 2.6.16.60-0.85.1, 2.6.16.60-0.87.1, 2.6.16.60-0.89.1, 2.6.16.60-0.91.1, 2.6.16.60-0.93.1. Confirm kernel support with server vendor.61. Novell OES 2 SP2 is supported with this update.62. Novell OES is only supported with Fibre channel connectivity.63. Novell OES 2 SP3 is supported with this update.64. Driver Version 5.00.07 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com65. PowerPath 4.3.4 or higher is supported - please check support of PowerPath on the base Operating System66. Supported kernels: 2.6.5-7.244, 2.6.5-7.252, 2.6.5-7.257, 2.6.5-7.267, 2.6.5-7.276, 2.6.5-7.282, 2.6.5-7.283, 2.6.5-7.286, 2.6.5-7.287.3.

Confirm kernel support with server vendor.67. Host CLI iSCSI LUN Snap and Replication is supported in NAS 5.5.27 or higher68. Driver Version 5.00.04-d5 Driver is integrated into the kernel.69. Supported kernels: 2.6.16.21-0.8, 2.6.16.21-0.15, 2.6.16.21-0.25, 2.6.16.27-0.6, 2.6.16.27-0.9.

Confirm kernel support with server vendor.PowerPath 5.0 support begins with kernel 2.6.16.27-0.6.

70. Driver Version 5.00.04 Driver is integrated into the kernel. Available in the EMC-approved section of the QLogic website.http://www.qlogic.com71. Supported kernels: 2.6.5-7.201, 2.6.5-7.202.7.

Confirm kernel support with server vendor.72. Driver Version iSCSI initiator 4.0.188.18 The following NICs are not supported: 3COM-3C996B The software initiator is part of the operating system and not an EMC software

product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> TheDocument Library -> Host Connectivity for the complete installation information.


74. Supported kernels: 2.6.27.19-5.1, 2.6.27.21-0.1.2, 2.6.27.23-0.1, 2.6.27.25-0.1.1 2.6.27.29-0.1.1, 2.6.27.37-0.1.1, 2.6.27.39-0.3.1, 2.6.27.42-0.1.1, 2.6.27.45-0.1.1, 2.6.27.48-0.1.1,2.6.27.48-0.6.1, 2.6.27.48-0.12.1, 2.6.27.54-0.2.1. Confirm kernel support with server vendor.

SuSE SLES [IA64]SuSE

SuSE



EnvironmentExternal

Boot

1 SuSE SLES [IA64]113

Generic Vendor NIC 10/1005, 6, GenericVendor NIC GbE4

LAN Only1, 2 EMC Unified Storage VNXe3300(File/iSCSI)

1.1 N

1. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.2. Routed networks (layer 3) require iSCSI digest to be enabled.3. Supported kernels: 2.6.27.19-5.1, 2.6.27.21-0.1.2, 2.6.27.23-0.1, 2.6.27.25-0.1.1 2.6.27.29-0.1.1, 2.6.27.37-0.1.1, 2.6.27.39-0.3.1, 2.6.27.42-0.1.1, 2.6.27.45-0.1.1, 2.6.27.48-0.1.1,

2.6.27.48-0.6.1, 2.6.27.48-0.12.1, 2.6.27.54-0.2.1. Confirm kernel support with server vendor.4. Driver Version iSCSI Software Initiator 1.0-595 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please

refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library ->Host Connectivity for the complete installation information.

5. NIC teaming with the Linux software initiator is not supported.6. Driver Version iSCSI Software Initiator 2.x The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.

SuSE SLES [x86_64]SuSE

SuSE

No.Operating



StorageOperative

EnvironmentExternal

Boot Comments

1 SuSE SLES[x86_64] 10SP156


1.1 N

Storage Array


2 SuSE SLES[x86_64] 10SP410, 17, 18,19, 20

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT) rNDC (rack)3,21, 22, Broadcom Broadcom 57810 DP 10Gb DA/SFP+ CNA3, 21, 22,Dell Broadcom 57810 Dual Port 10GbE KR Blade Converged Mezz3,21, 22, QLogic QLE8240-SR-E-SP30, 32, 74, QLogicQLE8242-SR-E-SP30, 32, 74, QLogic QLE8250-CU-E-SP30, 32, 74,QLogic QLE8252-CU-E-SP30, 32, 74


N

3 SuSE SLES[x86_64] 10:SP156,SP252;

SuSE SLES[x86_64]:1073, 1177

Generic Vendor NIC GbE51 LAN Only5, 50 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

4 SuSE SLES[x86_64]1073

Generic Vendor NIC 10/10051 LAN Only5, 50 EMC UnifiedStorageVNXe3300(File/iSCSI)

1.1 N

5 SuSE SLES[x86_64]1073



1.1 Y See50, 64

6 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT) rNDC (rack)3,21, 22, Broadcom Broadcom 57810 DP 10Gb DA/SFP+ CNA3, 21, 22,Dell Broadcom 57810 Dual Port 10GbE KR Blade Converged Mezz3,21, 22


Y1, 29 See15, 16,23

7 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT) rNDC (rack)3,21, 22, Broadcom Broadcom 57810 DP 10Gb DA/SFP+ CNA3, 21, 22,Dell Broadcom 57810 Dual Port 10GbE KR Blade Converged Mezz3,21, 22, Generic Vendor NIC 10/1008, 53, Generic Vendor NIC 10GbE8,35, 36, 37, 38, Generic Vendor NIC GbE8, 53


N See23

8 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14

Emulex OCe10102-IM-E33, 34, 47, Emulex OCe10102-IX-E33, 34, 47,Generic Vendor NIC 10GbE8, 35, 36, 37, 38, Hewlett Packard QlogicQMH4062 1GbE iSCSI HBA for HP c-Class BladeSystem(488074-B21)39, 40, 41, 49


Y29

9 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14



Y1 See15, 16,23

10 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)39, 40, 41, 49, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)44, 49, 61, 62, QLogic QLA4010-E-SP43, 44,49, 54, 55, QLogic QLA4010C-E-SP43, 44, 49, 54, 55, QLogicQLE4060C-E-SP39, 40, 44, 46, 48, 49, QLogic QLE4062C-E-SP39, 40, 44,46, 48, 49


N

11 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14

Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)39, 40, 41, 49, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)44, 49, 61, 62, QLogic QLA4010-E-SP43, 44,49, 54, 55, QLogic QLA4010C-E-SP43, 44, 49, 54, 55, QLogicQLE4060C-E-SP39, 40, 44, 46, 48, 49, QLogic QLE4062C-E-SP39, 40, 44,46, 48, 49, QLogic QLE8240-SR-E-SP30, 31, 32, QLogicQLE8242-SR-E-SP30, 31, 32, QLogic QLE8250-CU-E-SP30, 31, 32,QLogic QLE8252-CU-E-SP30, 31, 32


N

12 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14



Y1 See15, 16

13 SuSE SLES[x86_64] 11SP19, 10, 11,12, 13, 14

QLogic QLA4050-E-SP39, 43, 44, 45, 46, 49, QLogic QLA4050-E-SP39,43, 44, 45, 49, QLogic QLA4050C-E-SP39, 43, 44, 45, 46, 49, QLogicQLA4050C-E-SP39, 43, 44, 45, 49, QLogic QLA4052C-E-SP39, 43, 44, 45,46, 49, QLogic QLA4052C-E-SP39, 43, 44, 45, 49, QLogicQLE4060C-E-SP39, 40, 44, 46, 48, 49, QLogic QLE4062C-E-SP39, 40, 44,46, 48, 49


Y

14 SuSE SLES[x86_64] 11SP29, 10, 11,12, 24

Broadcom Broadcom 57800s (2x 10Gb SFP+ / 2x1GbT) rNDC (rack)3,21, 76, Broadcom Broadcom 57810 DP 10Gb DA/SFP+ CNA3, 21, 75,Dell Broadcom 57810 Dual Port 10GbE KR Blade Converged Mezz3,21, 76, Emulex OCe11102-IM-E25, 26, 27, 28, EmulexOCe11102-IX-E25, 26, 27, 28


Y1, 29 See15, 16,23

15 SuSE SLES[x86_64] 11SP29, 10, 11,12, 24

Emulex OCe10102-IM-E26, 33, 34, Emulex OCe10102-IX-E26, 33, 34,Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)39, 40, 41, 42, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)42, 44, 61, 62, QLogic QLA4010-E-SP42, 43,44, 54, 55, QLogic QLA4010C-E-SP42, 43, 44, 54, 55, QLogicQLA4050-E-SP39, 42, 43, 44, 45, QLogic QLA4050-E-SP39, 42, 43, 44, 45,46, QLogic QLA4050C-E-SP39, 42, 43, 44, 45, QLogicQLA4050C-E-SP39, 42, 43, 44, 45, 46, QLogic QLA4052C-E-SP39, 42, 43,44, 45, QLogic QLA4052C-E-SP39, 42, 43, 44, 45, 46, QLogicQLE4060C-E-SP39, 40, 42, 44, 46, 48, QLogic QLE4062C-E-SP39, 40, 42,44, 46, 48


Y1, 29

16 SuSE SLES[x86_64] 11SP29, 10, 11,12, 24

Emulex OCe10102-IM-E26, 33, 34, Emulex OCe10102-IX-E26, 33, 34,Hewlett Packard Qlogic QMH4062 1GbE iSCSI HBA for HP c-ClassBladeSystem (488074-B21)39, 40, 41, 42, IBM QLogic iSCSI Exp Cardfor BladeCenter (26K6487)42, 44, 61, 62, QLogic QLA4010-E-SP42, 43,44, 54, 55, QLogic QLA4010C-E-SP42, 43, 44, 54, 55, QLogicQLA4050-E-SP39, 42, 43, 44, 45, QLogic QLA4050-E-SP39, 42, 43, 44, 45,46, QLogic QLA4050C-E-SP39, 42, 43, 44, 45, QLogicQLA4050C-E-SP39, 42, 43, 44, 45, 46, QLogic QLA4052C-E-SP39, 42, 43,44, 45, QLogic QLA4052C-E-SP39, 42, 43, 44, 45, 46, QLogicQLE4060C-E-SP39, 40, 42, 44, 46, 48, QLogic QLE4062C-E-SP39, 40, 42,44, 46, 48, QLogic QLE8240-SR-E-SP30, 32, 42, QLogicQLE8242-SR-E-SP30, 32, 42, QLogic QLE8250-CU-E-SP30, 32, 42,QLogic QLE8252-CU-E-SP30, 32, 42


Y1, 29

Storage Array


17 SuSE SLES[x86_64] 11SP29, 10, 11,12, 24

Generic Vendor NIC 10/1008, 53, Generic Vendor NIC 10GbE8, 35, 36,37, 38, Generic Vendor NIC GbE8, 53


Y1, 29 See23

18 SuSE SLES[x86_64] 11SP29, 10, 11,12, 24



Y1, 29 See15, 16

19 SuSE SLES[x86_64] 9SP258, 67, 69


1.1 N

20 SuSE SLES[x86_64] 9SP458



1.1 Y See50, 64

21 SuSE SLES[x86_64] 9:SP258, 67, 69,SP358, 66, 67



1.1 Y See50, 64

22 SuSE SLES[x86_64] 9:SP358, 66, 67,SP458


1.1 N

23 SuSE SLES[x86_64]: 10SP252, 1177


1.1 N


2. BIOS 5.0.113. Driver Version iSCSI Software Initiator The iSCSI utilities are needed to configure the software initiator and are a seperate package from the driver. Please refer to the Linux

distributor for the supported version with their distribution. Only the software initiator driver native to this Linux distributor's release is supported.4. Firmware Version 2.1.1a5. Routed networks (layer 3) require iSCSI digest to be enabled.6. The latest drivers (Broadcom 57710 chip) can be found at the Broadcom Support Site at:http://www.broadcom.com/support/ethernet_nic/netxtremeii10.php7. Broadcom iSCSI offload (without iboot) is supported with following adapters:


8. NIC teaming with the Linux software initiator is not supported.9. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.

10. SLES Xen kernel supported. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.11. EMC supports the following filesystems: ext2, ext3, reiserfs unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, please submit an RPQ.12. SGI's XFS filesystem is also supported for this configuration. Files that are part of the released distribution of the operating system (e.g. /, /etc, /usr, /opt, etc) must not reside on an

XFS filesystem. XFS is supported on non-operating system data only.13. Novell OES 11 is supported with this update.14. Supported kernels: 2.6.32.12-0.7, 2.6.32.13-0.4.1, 2.6.32.13-0.5.1, 2.6.32.19-0.2.1, 2.6.32.19-0.3.1, 2.6.32.23-0.3.1, 2.6.32.24-0.2, 2.6.32.27-0.2.2, 2.6.32.29-0.3.1, 2.6.32.36-0.5.2,

2.6.32.43-0.4.1, 2.6.32.45-0.3.2, 2.6.32.46-0.3.1, 2.6.32.49-0.3.1, 2.6.32.54-0.3. Confirm kernel support with server vendor.15. Please refer to the Host Bus Adapter note for the supported NICs.16. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.17. Supported kernels: 2.6.16.60-0.85.1, 2.6.16.60-0.87.1, 2.6.16.60-0.89.1, 2.6.16.60-0.91.1, 2.6.16.60-0.93.1. Confirm kernel support with server vendor.18. Novell OES 2 SP2 is supported with this update.19. Novell OES is only supported with Fibre channel connectivity.20. Novell OES 2 SP3 is supported with this update.21. BIOS 7.2.1 Driver can be downloaded from support.dell.com22. Driver Version 2.7.2.1k Driver can be downloaded from support.dell.com23. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.24. Supported kernels:3.0.13-0.27, 3.0.26-0.7. Confirm kernel support with server vendor.25. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com26. Driver Version 4.1.282.0 Driver is integrated into the kernel.27. Firmware Version 3.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com28. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com29. Broadcom iSCSI Boot is supported with the following IBM adapters: 46M6164/46M6168

iSCSI boot is supported with SUSE SLES 11 SP1Please visit http://www.IBM.com/support for the currently supported blade servers, firmware/driver versions and special install instructions.

30. BIOS 3.03 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com31. Driver Version 5.02.11.00.05.06-c3 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com32. Firmware Version 4.09.34 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com33. BIOS 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com34. Firmware Version 2.103.397.34 Available in the EMC-approved section of the Emulex website.http://www.emulex.com35. Driver Version 1.3.30-k2 In-kernel driver version supported with Cisco UCS mezzanine adapter. The software initiator is part of the operating system and not an EMC software


36. Driver Version iSCSI Software Initiator 2.x Driver is integrated into the kernel.37. EMC Celerra supported for Cisco UCS attach.38. Intel(R) 82558 and 82559 10GbE NICs must be configured with split header disabled. Refer to Intel Document #468569 - TA-193: Potential Receive Hang with Header Splitting.39. Firmware Version 3.01.00.49 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com40. BIOS 1.13 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com41. Firmware Version 3.01.00.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com42. Driver Version 5.02.00.00.11.2-k2 Driver is integrated into the kernel.43. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.44. Requires SANsurfer for installation and configuration and is available for download from the EMC-approved section of the QLogic website athttp://www.qlogic.com45. BIOS 1.08 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com46. Firmware Version 3.00.01.53 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com47. Driver Version 2.0.527.0 Driver is integrated into the kernel.48. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLE2460 HBAs with the same operating system version listed here.49. Driver Version 5.01.00.00.11.01-k14 Driver is integrated into the kernel.50. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.51. Driver Version iSCSI Software Initiator 1.0-595 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please refer


52. Supported kernels: 2.6.16.60-0.21, 2.6.16.60-0.23, 2.6.16.60-0.27, 2.6.16.60-0.30, 2.6.16.60-0.31, 2.6.16.60-0.33, 2.6.16.60-0.34, 2.6.16.60-0.35, 2.6.16.60-0.37, 2.6.16.60-0.39.3,2.6.16.60-0.42.4, 2.6.16.60-0.42.5, 2.6.16.60-0.42.7, 2.6.16.60-0.42.8, 2.6.16.60-0.42.9, 2.6.16.60-0.42.10, 2.6.16.60-0.42.11. Confirm kernel support with server vendor.


54. Firmware Version 3.00.00.16 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com55. BIOS 1.11 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com56. Supported kernels: 2.6.16.46-0.12, 2.6.16.46-0.14, 2.6.16.53-0.8, 2.6.16.53-0.16, 2.6.16.54-0.2.3, 2.6.16.54-0.2.5, 2.6.16.54-0.2.8. Confirm kernel support with server vendor.57. Driver Version iSCSI Software Initiator 1.0-795 Driver is integrated into the kernel. The software initiator is part of the operating system and not an EMC software product. Please refer


58. In accordance with the SUSE Linux Enterprise Product Support Lifecycle Policy, the regular 7 year life-cycle of SUSE Linux Enterprise Server 9 will end on August 31, 2011. All SLES9 configurations in the ESM will be frozen as of the publication of the August 2011 ESM. At this time, SLES 9 will no longer be publicly supported and will require an extended supportcontract from Novell in order for the SLES 9 configuration in the ESM to be supported by EMC. Extended and Self-Support from Novell is planned to end August 31, 2014.

59.

Storage Array


Driver Version iSCSI initiator 4.0.188.18 Driver is integrated into the kernel. The following NICs are not supported: 3COM-3C996B The software initiator is part of the operatingsystem and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n 300-002-672, that can be found on EMC'sPowerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.


61. BIOS 1.09a Available in the EMC-approved section of the QLogic website.http://www.qlogic.com62. Firmware Version 2.00.00.45 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com63. Driver Version 5.00.07 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com64. PowerPath 4.3.4 or higher is supported - please check support of PowerPath on the base Operating System65. Driver Version 2.103.397.0 Available in the EMC-approved section of the Emulex website.http://www.emulex.com66. Supported kernels: 2.6.5-7.244, 2.6.5-7.252, 2.6.5-7.257, 2.6.5-7.267, 2.6.5-7.276, 2.6.5-7.282, 2.6.5-7.283, 2.6.5-7.286, 2.6.5-7.287.3.

Confirm kernel support with server vendor.67. Host CLI iSCSI LUN Snap and Replication is supported in NAS 5.5.27 or higher68. Driver Version 5.00.04 Driver is integrated into the kernel. Available in the EMC-approved section of the QLogic website.http://www.qlogic.com69. Supported kernels: 2.6.5-7.201, 2.6.5-7.202.7.

Confirm kernel support with server vendor.70. Driver Version iSCSI initiator 4.0.188.18 The following NICs are not supported: 3COM-3C996B The software initiator is part of the operating system and not an EMC software



72. Driver Version 5.00.04-d5 Driver is integrated into the kernel.73. Supported kernels: 2.6.16.21-0.8, 2.6.16.21-0.15, 2.6.16.21-0.25, 2.6.16.27-0.6, 2.6.16.27-0.9.

Confirm kernel support with server vendor.PowerPath 5.0 support begins with kernel 2.6.16.27-0.6.

74. Driver Version 5.02.11.00.10.4-d2 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com75. Driver Version 2.7.2.1k Driver is integrated into the kernel. Only the software initiator driver native to this Linux distributor's release is supported.76. Driver Version 2.7.2.1k Driver is integrated into the kernel.77. Supported kernels: 2.6.27.19-5.1, 2.6.27.21-0.1.2, 2.6.27.23-0.1, 2.6.27.25-0.1.1 2.6.27.29-0.1.1, 2.6.27.37-0.1.1, 2.6.27.39-0.3.1, 2.6.27.42-0.1.1, 2.6.27.45-0.1.1, 2.6.27.48-0.1.1,

2.6.27.48-0.6.1, 2.6.27.48-0.12.1, 2.6.27.54-0.2.1. Confirm kernel support with server vendor.

VMware ESXVMware

VMware



StorageOperative

EnvironmentExternal

Boot Comments

1 VMware ESX 4.1(vSphere 4)4, 5, 6, 7,8, 9, 10, 11

Emulex OCe10102-FM-E (CNA)31, 32, 33, EmulexOCe10102-IM-E13, 14, Emulex OCe10102-IX-E13, 14,Emulex OCe11102-IM-E13, 24, 25, EmulexOCe11102-IX-E13, 24, 25


N, Y2, 3

2 VMware ESX 4.1(vSphere 4)4, 5, 6, 7,8, 9, 10, 11

Emulex OCe10102-IM-E13, 14, EmulexOCe10102-IX-E13, 14, Emulex OCe11102-IM-E13, 24, 25,Emulex OCe11102-IX-E13, 24, 25


N, Y2, 3

3 VMware ESX: 4.0(vSphere 4)4, 7, 8,4.1 (vSphere 4)4, 5,6, 7, 8, 9, 10, 11

Generic Vendor NIC 10GbE29, Generic Vendor NICGbE20, Generic Vendor NIC GbE23, 30

LAN Only1 EMC UnifiedStorage: VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

N


Generic Vendor NIC GbE26, 28 LAN Only1 EMC UnifiedStorage VNXe3300(File/iSCSI)

1.1 Y See21, 22, 27


QLogic QLA4050C-E-SP12, 15, 16, 17, QLogicQLA4050C-E-SP12, 15, 18, 19, QLogicQLA4052C-E-SP12, 15, 16, 17, QLogicQLA4052C-E-SP12, 15, 18, 19, QLogicQLE4060C-E-SP12, QLogic QLE4060C-E-SP12, 18, 19,QLogic QLE4062C-E-SP12, QLogic QLE4062C-E-SP12,18, 19


Y2, 3


QLogic QLA4050C-E-SP15, 23, QLogicQLA4052C-E-SP15, 23, QLogic QLE4060C-E-SP23,QLogic QLE4062C-E-SP23


1.1 Y2, 3 See21, 22

1. Routed networks (layer 3) require iSCSI digest to be enabled.2. Virtual machines running on VMWare ESX are supported booting from the array.3. VMWare ESX Server itself is supported booting from external array.4. EMC supports VMware's recommendations for number of nodes in native ESX cluster configurations.5. Oracle Database 11g R1 is supported on VMware vSphere 4.0 Virtual Machines with Symmetrix, CLARiiON, and Celerra storage platforms. For details, refer to






10. Supported with vMotion.11. All released updates to ESX version are supported unless otherwise specified by a footnote. Please contact server vendor for the update level required for a specific server.12. Driver Version 3.30 This driver is included in the VMware ESX kernel. Driver upgrades not supported.13. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com14. Driver Version 2.102.525.9 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools Available in the EMC-approved section of the

Emulex website. http://www.emulex.com15. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.16. BIOS 1.09 Available at http://www.qlogic.com17. Firmware Version 2.00.00.45 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com18. BIOS 1.1419. Firmware Version 3.00.01.4020. Driver Version iSCSI initiator 3.6.3 This driver is included in the VMware ESX kernel. Driver upgrades not supported.21. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.22. Host CLI iSCSI LUN Snap and Replication is supported using the Linux guest OS initiator23. Driver Version In-box driver This driver is included in the VMware ESX kernel. Driver upgrades not supported.24. BIOS 4..03.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com25. Driver Version 4.0.317.1 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools Available in the EMC-approved section of the

Emulex website. http://www.emulex.com26. The following NICs are not supported: 3COM-3C996B27. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.28. Driver Version In-box iSCSI initiator This driver is included in the VMware ESX kernel. Driver upgrades not supported.29. Driver Version 2.0-865 This driver is included in the VMware ESX kernel. Driver upgrades not supported.30. Please refer to Primus case emc214707 at http://csexplorer.isus.emc.com/eservice/iviewcs/ui/eserver.asp for a required fix.31. BIOS 2.702.200.17 Available in the EMC-approved section of the Emulex website.http://www.emulex.com32. Driver Version 2.1.102.525.9 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools iSCSI Driver

Storage Array


33. Firmware Version 2.703.269..2806 Available in the EMC-approved section of the Emulex website.http://www.emulex.com

VMware ESXiVMware

VMware



StorageOperative

EnvironmentExternal

Boot Comments

1 VMware ESXi 4.1(vSphere 4)9, 10, 11, 13,17, 18, 19, 20

Emulex OCe10102-FM-E (CNA)15, 16, 21, EmulexOCe10102-IM-E4, 30, Emulex OCe10102-IX-E4, 30,Emulex OCe11102-IM-E4, 35, 36, EmulexOCe11102-IX-E4, 35, 36


N, Y6, 7

2 VMware ESXi 4.1(vSphere 4)9, 10, 11, 13,17, 18, 19, 20

Emulex OCe10102-IM-E4, 30, EmulexOCe10102-IX-E4, 30, Emulex OCe11102-IM-E4, 35,36, Emulex OCe11102-IX-E4, 35, 36


N, Y6, 7

3 VMware ESXi 5.0(vSphere 5)9, 10, 11, 12,13



1.1 Y See1, 2, 14




1.1 Y6, 7 See1, 2


Emulex OCe11102-IM-E3, 4, 5, EmulexOCe11102-IX-E3, 4, 5, Generic Vendor NIC 10GbE22


N


Emulex OCe11102-IM-E3, 4, 5, EmulexOCe11102-IX-E3, 4, 5, Generic Vendor NIC GbE24, 25

LAN Only8 EMC UnifiedStorage VNXe3300(File)

1.1 Y See1, 2, 14


Emulex OCe11102-IM-E3, 4, 5, EmulexOCe11102-IX-E3, 4, 5, QLogic QLA4050C-E-SP22, 23,QLogic QLA4052C-E-SP22, 23, QLogicQLE4060C-E-SP22, QLogic QLE4062C-E-SP22

LAN Only8 EMC UnifiedStorage VNXe3300(File)

1.1 Y6, 7 See1, 2

8 VMware ESXi: 4.0(vSphere 4)9, 10, 11, 4.1(vSphere 4)9, 10, 11, 13,17, 18, 19, 20

Generic Vendor NIC 10GbE33, Generic Vendor NICGbE34


N

9 VMware ESXi: 4.0(vSphere 4)9, 10, 11, 4.1(vSphere 4)9, 10, 11, 13,17, 18, 19, 20

QLogic QLA4050C-E-SP23, 27, 28, 29, QLogicQLA4050C-E-SP23, 27, 31, 32, QLogicQLA4052C-E-SP23, 27, 28, 29, QLogicQLA4052C-E-SP23, 27, 31, 32, QLogicQLE4060C-E-SP27, QLogic QLE4060C-E-SP27, 31,32, QLogic QLE4062C-E-SP27, QLogicQLE4062C-E-SP27, 31, 32


Y6, 7

10 VMware ESXi: 4.0(vSphere 4)9, 10, 11, 4.1(vSphere 4)9, 10, 11, 13,17, 18, 19, 20, 5.0(vSphere 5)9, 10, 11, 12,13

Generic Vendor NIC GbE22, 26 LAN Only8 EMC UnifiedStorage: VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

N


Generic Vendor NIC GbE24, 25 LAN Only8 EMC UnifiedStorage VNXe3300(File/iSCSI)

1.1 Y See1, 2, 14


QLogic QLA4050C-E-SP22, 23, QLogicQLA4052C-E-SP22, 23, QLogic QLE4060C-E-SP22,QLogic QLE4062C-E-SP22


1.1 Y6, 7 See1, 2

1. LAN support includes direct connect (layer 2), switched (layer 2), or routed (layer 3) networks. Network should be designed to minimize packet loss or any other interruptions.2. Host CLI iSCSI LUN Snap and Replication is supported using the Linux guest OS initiator3. Driver Version 4.0.317.1 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools4. Firmware Version 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com5. BIOS 4.0.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com6. Virtual machines running on VMWare ESX are supported booting from the array.7. VMWare ESX Server itself is supported booting from external array.8. Routed networks (layer 3) require iSCSI digest to be enabled.9. EMC supports VMware's recommendations for number of nodes in native ESX cluster configurations.



12. Supports 2-node Microsoft Cluster Services (MSCS) with Windows 2003 and Windows 2008 virtual machines in CIB (Cluster in Box) and CAB (Cluster across Boxes) configurationsfor Fibre Channel configurations. VMware NMP (Native Multipathing) and PowerPath/VE are supported with MSCS.

13. All released updates to ESX version are supported unless otherwise specified by a footnote. Please contact server vendor for the update level required for a specific server.14. The software initiator is part of the operating system and not an EMC software product. Please refer to the required release note "EMC Linux iSCSI Attach Release Notes", p/n

300-002-672, that can be found on EMC's Powerlink website in Support -> The Document Library -> Host Connectivity for the complete installation information.15. Driver Version 2.1.102.525.9 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools iSCSI Driver16. Firmware Version 2.703.269..2806 Available in the EMC-approved section of the Emulex website.http://www.emulex.com17. Oracle Database 11g R1 is supported on VMware vSphere 4.0 Virtual Machines with Symmetrix, CLARiiON, and Celerra storage platforms. For details, refer to




20. Supported with vMotion.21. BIOS 2.702.200.17 Available in the EMC-approved section of the Emulex website.http://www.emulex.com22. Driver Version In-box driver This driver is included in the VMware ESX kernel. Driver upgrades not supported.23. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.24. Driver Version In-box iSCSI initiator This driver is included in the VMware ESX kernel. Driver upgrades not supported.25. The following NICs are not supported: 3COM-3C996B26. Please refer to Primus case emc214707 at http://csexplorer.isus.emc.com/eservice/iviewcs/ui/eserver.asp for a required fix.27. Driver Version 3.30 This driver is included in the VMware ESX kernel. Driver upgrades not supported.28. BIOS 1.09 Available at http://www.qlogic.com29. Firmware Version 2.00.00.45 Available in the EMC-approved section of the QLogic website.http://www.qlogic.com30. Driver Version 2.102.525.9 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools Available in the EMC-approved section of the

Emulex website. http://www.emulex.com

Storage Array


31. BIOS 1.1432. Firmware Version 3.00.01.4033. Driver Version 2.0-865 This driver is included in the VMware ESX kernel. Driver upgrades not supported.34. Driver Version iSCSI initiator 3.6.3 This driver is included in the VMware ESX kernel. Driver upgrades not supported.35. BIOS 4..03.360.3 Available in the EMC-approved section of the Emulex website.http://www.emulex.com36. Driver Version 4.0.317.1 Available at http://downloads.vmware.com/d/info/datacenter_downloads/vmware_vsphere_4/4#drivers_tools Available in the EMC-approved section of the

Emulex website. http://www.emulex.com

Path Management SoftwareConfiguration Notes

This table describes the support statements for path management software such as EMC PowerPath and native offerings built into the Operating System inEMC Symmetrix and CLARiiON environments. Veritas DMP support statements are found on the Veritas Volume Management table. For HBA and driversupport, see the Base Connectivity table. For PowerPath support with non-EMC storage, see the Path Management Software - Third Party Arrays table. Whenreferencing PowerPath information from the ELN posted PDFs, PowerPath and PowerPath/VE information may be listed in separate documents that areavailable in the same download section.

Asianux AX [32-Bit]Asianux

Asianux

No. Storage Array Operating System

MultipathSoftware(Infrastructure

Software) Storage Operating Environment

1 EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300 (File/iSCSI)

Asianux AX [32-Bit]: 4.0SP13, 5, 6, 4.03, 4, 5

Asianux DM-MPIO1, 2;EMC PowerPath 5.6

EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.1

1. The device mapper and multipath tools package included in the distribution is required for support. Please refer to the "Native MultipathFailover" chapter of the "EMC Host Connectivity Guide for Linux" available via PowerLink for required packages and configuration instructions.

2. This product is also known as Linux Native Multipathing.3. Native multipathing is not supported on boot-from-SAN configurations.4. Supported kernels: 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6. Confirm kernel support with server vendor.5. Asianux includes separate releases from Redflag DC Server, Miracle Linux and HanCom Linux Server. Each individual distribution is released asynchronous of the other. Please

review the individual distributors release to ensure the availabilty of that desired release.6. Supported kernels: 2.6.32-131.12.1.el6. Confirm kernel support with server vendor.

Asianux AX [x86_64]Asianux

Asianux





Asianux AX [x86_64]: 4.0SP11, 3, 4, 4.01, 2, 3

Asianux DM-MPIO5, 6;EMC PowerPath 5.6

EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.1

1. Native multipathing is not supported on boot-from-SAN configurations.2. Supported kernels: 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6. Confirm kernel support with server vendor.3. Asianux includes separate releases from Redflag DC Server, Miracle Linux and HanCom Linux Server. Each individual distribution is released asynchronous of the other. Please

review the individual distributors release to ensure the availabilty of that desired release.4. Supported kernels: 2.6.32-131.12.1.el6. Confirm kernel support with server vendor.5. The device mapper and multipath tools package included in the distribution is required for support. Please refer to the "Native Multipath

Failover" chapter of the "EMC Host Connectivity Guide for Linux" available via PowerLink for required packages and configuration instructions.6. This product is also known as Linux Native Multipathing.


Microsoft



Software)Supported RSA Key

Manager Storage Operating Environment

1 EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300 (File/iSCSI)

Microsoft Windows 2003 [x64]DataCenter: R2 SP2, SP2;

Microsoft Windows 2003 [x64]Enterprise Edition: R2 SP2,SP2;

Microsoft Windows 2003 [x64]Standard Edition: R2 SP2,SP2;

Microsoft Windows 2003 [x64]Storage Server EnterpriseEdition: R2 SP2, SP2;

Microsoft Windows 2003 [x64]Storage Server StandardEdition: R2 SP2, SP2

EMC PowerPath 5.51, 2, 3 RKM appliance version2.7 SP1 (Softwareverion 2.7 SP1

EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.0, EMC VNXe iSCSI OE2.0.0, EMC VNXe iSCSI OE 2.1.1


Microsoft Windows 2003 [x64]DataCenter: R2 SP2, SP2;

Microsoft Windows 2003 [x64]Enterprise Edition: R2 SP2,SP2;

Microsoft Windows 2003 [x64]Standard Edition: R2 SP2,SP2;

Microsoft Windows 2003 [x64]Storage Server EnterpriseEdition: R2 SP2, SP2;

Microsoft Windows 2003 [x64]Storage Server StandardEdition: R2 SP2, SP2

EMC PowerPath: 5.3 SP13, 5.5SP1


1. For encryption support please refer to the PowerPath and PowerPath/VE Family for Windows Release Notes.

Storage Array


2. Requires mandatory patch 5.5 P01 if using PowerPath Encryption with RSA or PowerPath Migration Enabler features.3. Support of VSS Provider requires minimum Solution Enabler 7.0.0.0


Microsoft






Microsoft Windows 2003[x86] DataCenter: R2 SP2,SP2;

Microsoft Windows 2003[x86] Enterprise Edition: R2SP2, SP2;

Microsoft Windows 2003[x86] Standard Edition: R2SP2, SP2

EMC PowerPath 5.51, 2, 3 RKM appliance version2.7 SP1 (Softwareverion 2.7 SP1

EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.0, EMC VNXe iSCSI OE2.1.1


Microsoft Windows 2003[x86] DataCenter: R2 SP2,SP2;

Microsoft Windows 2003[x86] Enterprise Edition: R2SP2, SP2;

Microsoft Windows 2003[x86] Standard Edition: R2SP2, SP2



1. Support of VSS Provider requires minimum Solution Enabler 7.0.0.02. For encryption support please refer to the PowerPath and PowerPath/VE Family for Windows Release Notes.3. Requires mandatory patch 5.5 P01 if using PowerPath Encryption with RSA or PowerPath Migration Enabler features.


Microsoft





1 EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300 (File/iSCSI)1

Microsoft Windows 2008 R2 SP1[x64]: DataCenter, EnterpriseEdition, Standard Edition, StorageServer

EMC PowerPath 5.52, 3, 4 RKM applianceversion 2.7 SP1(Software verion 2.7SP1

EMC VNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.0, EMC VNXeiSCSI OE 2.1.1


Microsoft Windows 2008 R2 SP1[x64]: DataCenter, EnterpriseEdition, Standard Edition, StorageServer

EMC PowerPath: 5.3 SP14,5.5 SP1

EMC VNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.0, EMC VNXeiSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.1


2. For encryption support please refer to the PowerPath and PowerPath/VE Family for Windows Release Notes.3. Requires mandatory patch 5.5 P01 if using PowerPath Encryption with RSA or PowerPath Migration Enabler features.4. Support of VSS Provider requires minimum Solution Enabler 7.0.0.0


Microsoft




ManagerStorage Operating

Environment


Microsoft Windows 2008 R2 [x64]:DataCenter, Enterprise Edition,Standard Edition, Storage Server

EMC PowerPath 5.52, 3, 4 RKM appliance version2.7 SP1 (Software verion2.7 SP1

EMC VNXe iSCSI OE2.0.0, EMC VNXe iSCSIOE 2.1.0, EMC VNXeiSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.1


Microsoft Windows 2008 R2 [x64]:DataCenter, Enterprise Edition,Standard Edition, Storage Server


EMC VNXe iSCSI OE2.0.0, EMC VNXe iSCSIOE 2.1.0, EMC VNXeiSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.1


2. For encryption support please refer to the PowerPath and PowerPath/VE Family for Windows Release Notes.3. Requires mandatory patch 5.5 P01 if using PowerPath Encryption with RSA or PowerPath Migration Enabler features.4. Support of VSS Provider requires minimum Solution Enabler 7.0.0.0


Microsoft



Software)Supported RSA

Key Manager Storage Operating Environment

Storage Array



Microsoft Windows 2008 [x64]: DataCenter,DataCenter SP2, Enterprise Edition, EnterpriseEdition SP2, Standard Edition, Standard EditionSP2, Storage Server, Storage Server SP2, WebServer


EMC VNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.0, EMCVNXe iSCSI OE 2.1.1


Microsoft Windows 2008 [x64]: DataCenter,DataCenter SP2, Enterprise Edition, EnterpriseEdition SP2, Standard Edition, Standard EditionSP2, Storage Server, Storage Server SP2, WebServer


EMC VNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.0, EMCVNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.1

1. Support of VSS Provider requires minimum Solution Enabler 7.0.0.02. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" Quorum

Configuration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."3. For encryption support please refer to the PowerPath and PowerPath/VE Family for Windows Release Notes.4. Requires mandatory patch 5.5 P01 if using PowerPath Encryption with RSA or PowerPath Migration Enabler features.


Microsoft




Key Manager Storage Operating Environment


Microsoft Windows 2008 [x86]: DataCenter,DataCenter SP2, Enterprise Edition,Enterprise Edition SP2, Standard Edition,Standard Edition SP2, Web Server


EMC VNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.0, EMC VNXeiSCSI OE 2.1.1


Microsoft Windows 2008 [x86]: DataCenter,DataCenter SP2, Enterprise Edition,Enterprise Edition SP2, Standard Edition,Standard Edition SP2, Web Server


EMC VNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.0, EMC VNXeiSCSI OE 2.0.0, EMC VNXe iSCSIOE 2.1.1


2. Support of VSS Provider requires minimum Solution Enabler 7.0.0.03. For encryption support please refer to the PowerPath and PowerPath/VE Family for Windows Release Notes.4. Requires mandatory patch 5.5 P01 if using PowerPath Encryption with RSA or PowerPath Migration Enabler features.

Oracle Linux UEK [x86_64]Oracle

Oracle





Oracle Linux UEK [x86_64]:5.65, 6.08, 6.11

EMC PowerPath 5.6 P01 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.1.1


Oracle Linux UEK [x86_64]5.77

EMC PowerPath 5.6 P02 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.1


Oracle Linux UEK [x86_64]:5.65, 5.77, 6.08, 6.11, 6.29

Oracle DM-MPIO2, 3, 4 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.1.1


Oracle Linux UEK [x86_64]5.86

Oracle DM-MPIO3, 4 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.1.1

1. Supported kernels: 2.6.32-100.34.1.el6uek. Confirm kernel support with server vendor.2. IO running to a failed path when using PNR devices will queue until the fault is fixed. No error will be reported to the application. If a new IO thread is started to the same device

DM-MPIO will send it down an alternate path. This behavior is not seen when using ALUA.3. The device mapper and multipath tools package included in the distribution is required for support. Please refer to the "Native Multipath

Failover" chapter of the "EMC Host Connectivity Guide for Linux" available via PowerLink for required packages and configuration instructions.4. This product is also known as Linux Native Multipathing.5. Supported kernels: 2.6.32-100.28.1.el5, 2.6.32-100.28.9.el5, 2.6.32-100.28.11.el5, 2.6.32-100.28.15.el5; 2.6.32-100.28.17.el5, 2.6.32-100.35.1.el5uek. Confirm kernel support with

server vendor.6. Supported kernels: 2.6.32-300.10.1.el5uek, 2.6.32-300.11.1.el5uek, 2.6.32-300.20.1.el5uek, 2.6.32-300.21.1.el5uek, 2.6.32-300.24.1.el5uek, 2.6.32-300.25.1.el5uek. Confirm

kernel support with server vendor.7. Supported kernels: 2.6.32-200.13.1.el5uek, 2.6.32-200.16.1.el5uek, 2.6.32-200.19.1.el5uek, 2.6.32-200.20.1.el5uek, 2.6.32-200.23.1.el5uek. Confirm kernel support with

server vendor.8. Supported kernels: 2.6.32-100.28.1.el6, 2.6.32-100.28.9.el6, 2.6.32-100.28.11.el6, 2.6.32-100.28.15.el6, 2.6.32-100.28.17.el6, 2.6.32-100.35.1.el6uek. Confirm kernel support

with server vendor.9. Supported kernels: 2.6.32-300.3.1.el6uek, 2.6.32-300.4.1.el6uek, 2.6.32-300.7.1.el6uek, 2.6.32-300.11.1.el6uek, 2.6.32-300.20.1.el6uek, 2.6.32-300.21.1.el6uek. Confirm

kernel support with server vendor.

Oracle Linux [32-Bit]Oracle

Oracle






Oracle Linux [32-Bit]5.63, 7

EMC PowerPath 5.5 EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.0, EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.1


Oracle Linux [32-Bit]5.63, 7

EMC PowerPath 5.5 RKM appliance version2.7 SP1 (software version2.7 SP1)

EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.0, EMC VNXe iSCSI OE 2.1.1


Oracle Linux [32-Bit]:5.63, 7, 5.73, 4, 5

EMC PowerPath 5.6;Red Hat DM-MPIO1, 2


Storage Array



Oracle Linux [32-Bit]:5.63, 7, 5.73, 4, 5, 5.83, 5,6

Oracle DM-MPIO1, 2 EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.0, EMC VNXe iSCSI OE 2.1.1


2. This product is also known as Linux Native Multipathing.3. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.4. Supported kernels: 2.6.18-274.0.0.0.1.el5, 2.6.18-274.12.1.0.1.el5, 2.6.18-274.17.1.0.1.el5. Confirm kernel support with server vendor.5. OEL Xen kernel supported.6. Supported kernels: 2.6.18-308.0.0.0.1.el5. Confirm kernel support with server vendor.7. Supported kernels: 2.6.18-238.0.1.el5, 2.6.18-238.1.1.0.1.el5, 2.6.18-238.5.1.0.1.el5, 2.6.18-238.9.1.0.1.el5, 2.6.18-238.12.1.0.1.el5. Confirm kernel support with server vendor.


Oracle






Oracle Linux [x86_64]5.63, 7

EMC PowerPath 5.5 EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.0, EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.1


Oracle Linux [x86_64]5.63, 7

EMC PowerPath 5.5 RKM appliance version2.7 SP1 (software version2.7 SP1)



Oracle Linux [x86_64]:5.63, 7, 5.73, 4, 5




Oracle Linux [x86_64]:5.63, 7, 5.73, 4, 5, 5.83, 5,6

Oracle DM-MPIO1, 2 EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.0, EMC VNXe iSCSI OE 2.1.1


2. This product is also known as Linux Native Multipathing.3. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.4. Supported kernels: 2.6.18-274.0.0.0.1.el5, 2.6.18-274.12.1.0.1.el5, 2.6.18-274.17.1.0.1.el5. Confirm kernel support with server vendor.5. OEL Xen kernel supported.6. Supported kernels: 2.6.18-308.0.0.0.1.el5. Confirm kernel support with server vendor.7. Supported kernels: 2.6.18-238.0.1.el5, 2.6.18-238.1.1.0.1.el5, 2.6.18-238.5.1.0.1.el5, 2.6.18-238.9.1.0.1.el5, 2.6.18-238.12.1.0.1.el5. Confirm kernel support with server vendor.


Oracle

No. Storage Array Operating SystemMultipath Software(Infrastructure


1 EMC Unified StorageVNXe3300 (File/iSCSI)

Oracle Solaris 10:SPARC4, x865;

Oracle Solaris 11:SPARC2, x863

Oracle MPxIO1 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0, EMCVNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.1

1. Also known as Sun StorEdge Traffic Manager2. EMC recommends as a best practice that customers upgrade to the most recent Solaris 11 SPARC SRU released on the Oracle website:http://support.oracle.com3. EMC recommends as a best practice that customers upgrade to the most recent Solaris 11 x86 SRU released on the Oracle website:http://support.oracle.com4. For LDOM support, please refer to the 'Virtualization Server Support' table available via EMC PowerLink:

https://elabnavigator.emc.com/emcpubs/elab/esm/pdf/Virtualization_Server_Support.pdf5. EMC supports ZFS in Solaris 10_x86 11/06 (update 3) or later. The Snapshot and Clone features of ZFS are supported only through Sun Microsystems.


Red Hat




Key ManagerStorage Operating

Environment Comments


Red Hat RHEL [32-Bit] 5.62, 3, 4, 10 EMC PowerPath 5.5 RKM applianceversion 2.7 SP1(software version2.7 SP1)

EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.1


Red Hat RHEL [32-Bit] 5.71, 2, 3, 4 EMC PowerPath 5.5 EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.1

See5


Red Hat RHEL [32-Bit]: 5.52, 3, 4,14, 5.62, 3, 4, 10

EMC PowerPath 5.5 EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.1


Red Hat RHEL [32-Bit]: 5.52, 3, 4,14, 5.62, 3, 4, 10, 5.71, 2, 3, 4, 5.82, 3,4, 6, 6.03, 4, 15, 6.13, 4, 16, 6.23, 4, 11,12, 13, 6.33, 4, 7


EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0,EMC VNXe iSCSI OE 2.1.1

1. Supported kernels: 2.6.18-274.el5, 2.6.18-274.3.1el5, 2.6.18-274.7.1.el5, 2.6.18-274.12.1.el5, 2.6.18-274.17.1.el5, 2.6.18-274.18.1.el5. Confirm kernel support with server vendor.2. RHEL Xen kernel supported. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.3. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.4. RHEL KVM is supported but not with EMC PowerPath. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.5. Booting from the SAN with PowerPath is supported. Refer to the Path Management Software section for supported versions of PowerPath.6. Supported kernels:2.6.18-308.el5, 2.6.18-308.1.1.el5, 2.6.18-308.4.1.el5. Confirm kernel support with server vendor.7. Supported kernels: 2.6.32-279.el6. Confirm kernel support with server vendor.8. The device mapper and multipath tools package included in the distribution is required for support. Please refer to the "Native Multipath


10. Supported kernels: 2.6.18-238.el5, 2.6.18-238.1.1.el5, 2.6.18-238.5.1.el5, 2.6.18-238.9.1.el5, 2.6.18-238.12.1.el5, 2.6.18-238.19.1.el5, 2.6.18-238.21.1.el5, 2.6.18-238.27.1.el5,2.6.18-238.28.1.el5, 2.6.18-238.31.1.el5, 2.6.18-238.33.1.el5, 2.6.18-238.35.1.el5, 2.6.18-238.37.1.el5. Confirm kernel support with server vendor.

11. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.

Storage Array


12. EMC supports the following filesystems: ext2, ext3, ext4, xfs, gfs, and gfs2 unless otherwise noted in the ESM. If there is a customer requirement for a different filesystem, pleasesubmit an RPQ.

13. Supported kernels: 2.6.32-220.el6, 2.6.32-220.2.1.el6, 2.6.32-220.4.1.el6, 2.6.32-220.4.2.el6, 2.6.32-220.7.1.el6, 2.6.32-220.13.1.el6, 2.6.32-220.17.1.el6. Confirm kernel supportwith server vendor.

14. Supported kernels: 2.6.18-194.el5, 2.6.18-194.3.1.el5, 2.6.18-194.8.1.el5, 2.6.18-194.11.1.el5, 2.6.18-194.11.3.el5, 2.6.18-194.11.4.el5, 2.6.18-194.17.1.el5, 2.6.18-194.17.4.el5,2.6.18-194.26.1.el5, 2.6.18-194.32.1.el5 Confirm kernel support with server vendor.

15. Supported kernels: 2.6.32-71.el6, 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6, 2.6.32-71.24.1.el6, 2.6.32-71.31.1.el6, 2.6.32-71.34.1.el6,2.6.32-71.36.1.el6, 2.6.32-71.37.1.el6, 2.6.32-71.38.1.el6. Confirm kernel support with server vendor.

16. Supported kernels: 2.6.32-131.0.15.el6, 2.6.32-131.2.1.el6, 2.6.32-131.6.1.el6, 2.6.32-131.12.1.el6, 2.6.32-131.17.1.el6, 2.6.32-131.21.1.el6, 2.6.32-131.25.1.el6. Confirm kernelsupport with server vendor.

Red Hat RHEL [IA64]Red Hat

Red Hat

No. Storage ArrayOperating

System





Red Hat RHEL[IA64] 5.64, 5, 6, 7

EMC PowerPath 5.5 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSIOE 2.1.0, EMC VNXe iSCSI OE 2.0.0, EMCVNXe iSCSI OE 2.1.1


Red Hat RHEL[IA64] 5.64, 5, 6, 7

EMC PowerPath 5.5 RKM appliance version 2.7SP1 (software version 2.7SP1)

EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSIOE 2.1.0, EMC VNXe iSCSI OE 2.1.1


Red Hat RHEL[IA64] 5.73, 4

Red Hat DM-MPIO1, 2 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSIOE 2.1.0, EMC VNXe iSCSI OE 2.1.1


2. This product is also known as Linux Native Multipathing.3. Supported kernels: 2.6.18-274.el5, 2.6.18-274.3.1el5, 2.6.18-274.7.1.el5, 2.6.18-274.12.1.el5, 2.6.18-274.17.1.el5, 2.6.18-274.18.1.el5. Confirm kernel support with server vendor.4. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.5. RHEL Xen kernel supported. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.6. Supported kernels: 2.6.18-238.el5, 2.6.18-238.1.1.el5, 2.6.18-238.5.1.el5, 2.6.18-238.9.1.el5, 2.6.18-238.12.1.el5, 2.6.18-238.19.1.el5, 2.6.18-238.21.1.el5, 2.6.18-238.27.1.el5,

2.6.18-238.28.1.el5, 2.6.18-238.31.1.el5, 2.6.18-238.33.1.el5, 2.6.18-238.35.1.el5, 2.6.18-238.37.1.el5. Confirm kernel support with server vendor.7. RHEL KVM is supported but not with EMC PowerPath. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.


Red Hat




Manager

StorageOperating



Red Hat RHEL [x86_64] 5.62, 3, 4, 8 EMC PowerPath 5.5 EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.0,EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.1


Red Hat RHEL [x86_64] 5.71, 2, 3, 4 EMC PowerPath 5.5 EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.0,EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.1

See5


Red Hat RHEL [x86_64]: 5.52, 3, 4, 7,5.62, 3, 4, 8

EMC PowerPath 5.5 RKM appliance version2.7 SP1 (softwareversion 2.7 SP1)

EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.0,EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.1


Red Hat RHEL [x86_64]: 5.52, 3, 4, 7,5.62, 3, 4, 8, 5.71, 2, 3, 4, 5.82, 3, 4, 6,6.03, 4, 14, 6.13, 4, 15, 6.23, 4, 9, 10, 11


EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.0,EMC VNXeiSCSI OE 2.0.0,EMC VNXeiSCSI OE 2.1.1

1. Supported kernels: 2.6.18-274.el5, 2.6.18-274.3.1el5, 2.6.18-274.7.1.el5, 2.6.18-274.12.1.el5, 2.6.18-274.17.1.el5, 2.6.18-274.18.1.el5. Confirm kernel support with server vendor.2. RHEL Xen kernel supported. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.3. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.4. RHEL KVM is supported but not with EMC PowerPath. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.5. Booting from the SAN with PowerPath is supported. Refer to the Path Management Software section for supported versions of PowerPath.6. Supported kernels:2.6.18-308.el5, 2.6.18-308.1.1.el5, 2.6.18-308.4.1.el5. Confirm kernel support with server vendor.7. Supported kernels: 2.6.18-194.el5, 2.6.18-194.3.1.el5, 2.6.18-194.8.1.el5, 2.6.18-194.11.1.el5, 2.6.18-194.11.3.el5, 2.6.18-194.11.4.el5, 2.6.18-194.17.1.el5, 2.6.18-194.17.4.el5,

2.6.18-194.26.1.el5, 2.6.18-194.32.1.el5 Confirm kernel support with server vendor.8. Supported kernels: 2.6.18-238.el5, 2.6.18-238.1.1.el5, 2.6.18-238.5.1.el5, 2.6.18-238.9.1.el5, 2.6.18-238.12.1.el5, 2.6.18-238.19.1.el5, 2.6.18-238.21.1.el5, 2.6.18-238.27.1.el5,

2.6.18-238.28.1.el5, 2.6.18-238.31.1.el5, 2.6.18-238.33.1.el5, 2.6.18-238.35.1.el5, 2.6.18-238.37.1.el5. Confirm kernel support with server vendor.9. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.




13. This product is also known as Linux Native Multipathing.14. Supported kernels: 2.6.32-71.el6, 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6, 2.6.32-71.24.1.el6, 2.6.32-71.31.1.el6, 2.6.32-71.34.1.el6,

2.6.32-71.36.1.el6, 2.6.32-71.37.1.el6, 2.6.32-71.38.1.el6. Confirm kernel support with server vendor.15. Supported kernels: 2.6.32-131.0.15.el6, 2.6.32-131.2.1.el6, 2.6.32-131.6.1.el6, 2.6.32-131.12.1.el6, 2.6.32-131.17.1.el6, 2.6.32-131.21.1.el6, 2.6.32-131.25.1.el6. Confirm kernel

support with server vendor.

Storage Array



Red Hat




Red Hat RHEL [x86_84]6.31, 2, 3


EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.0, EMC VNXe iSCSI OE 2.1.1

1. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMCHost Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.

2. Supported kernels: 2.6.32-279.el6. Confirm kernel support with server vendor.3. RHEL KVM is supported but not with EMC PowerPath. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.4. The device mapper and multipath tools package included in the distribution is required for support. Please refer to the "Native Multipath


SuSE SLES [32-Bit]SuSE

SuSE





SuSE SLES [32-Bit] 11 SP15,6, 7, 8, 9

EMC PowerPath 5.5 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.1


SuSE SLES [32-Bit] 11: SP15,6, 7, 8, 9, SP24, 5, 6, 7

SuSE DM-MPIO1, 2, 3 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE 2.1.0,EMC VNXe iSCSI OE 2.1.1

1. SLES 11 kernel 2.6.27.21-0.1.2 or higher is required for environments running DM-MPIO with CLARiiON.2. The device mapper and multipath tools package included in the distribution is required for support. Please refer to the "Native Multipath

Failover" chapter of the "EMC Host Connectivity Guide for Linux" available via PowerLink for required packages and configuration instructions.3. This product is also known as Linux Native Multipathing.4. Supported kernels:3.0.13-0.27, 3.0.26-0.7. Confirm kernel support with server vendor.5. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.6. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMC

Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.7. SLES Xen kernel supported. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.8. Novell OES 11 is supported with this update.9. Supported kernels: 2.6.32.12-0.7, 2.6.32.13-0.4.1, 2.6.32.13-0.5.1, 2.6.32.19-0.2.1, 2.6.32.19-0.3.1, 2.6.32.23-0.3.1, 2.6.32.24-0.2, 2.6.32.27-0.2.2, 2.6.32.29-0.3.1, 2.6.32.36-0.5.2,

2.6.32.43-0.4.1, 2.6.32.45-0.3.2, 2.6.32.46-0.3.1, 2.6.32.49-0.3.1, 2.6.32.54-0.3. Confirm kernel support with server vendor.


SuSE





SuSE SLES [x86_64] 11 SP11,2, 3, 4, 5

EMC PowerPath 5.5 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.0, EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSIOE 2.1.1


SuSE SLES [x86_64] 11:SP11, 2, 3, 4, 5, SP21, 2, 3, 9

SuSE DM-MPIO6, 7, 8 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.0, EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSIOE 2.1.1


Host Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.3. SLES Xen kernel supported. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.4. Novell OES 11 is supported with this update.5. Supported kernels: 2.6.32.12-0.7, 2.6.32.13-0.4.1, 2.6.32.13-0.5.1, 2.6.32.19-0.2.1, 2.6.32.19-0.3.1, 2.6.32.23-0.3.1, 2.6.32.24-0.2, 2.6.32.27-0.2.2, 2.6.32.29-0.3.1, 2.6.32.36-0.5.2,

2.6.32.43-0.4.1, 2.6.32.45-0.3.2, 2.6.32.46-0.3.1, 2.6.32.49-0.3.1, 2.6.32.54-0.3. Confirm kernel support with server vendor.6. SLES 11 kernel 2.6.27.21-0.1.2 or higher is required for environments running DM-MPIO with CLARiiON.7. The device mapper and multipath tools package included in the distribution is required for support. Please refer to the "Native Multipath

Failover" chapter of the "EMC Host Connectivity Guide for Linux" available via PowerLink for required packages and configuration instructions.8. This product is also known as Linux Native Multipathing.9. Supported kernels:3.0.13-0.27, 3.0.26-0.7. Confirm kernel support with server vendor.

VMware ESXVMware

VMware


Software)Storage Operating


1 EMC Unified Storage VNXe3100(File/iSCSI)

VMware ESX 4.0 (vSphere 4)2, 3,4

EMC PowerPath/VE 5.4 SP11;VMware NMP5

EMC VNXe iSCSIOE 2.0.0

See1


VMware ESX 4.1 (vSphere 4)2, 3,4, 7, 8, 9, 10, 11


EMC VNXe iSCSIOE 2.0.0


VMware ESX 4.1 (vSphere 4)2, 3,4, 7, 8, 9, 10, 11


EMC VNXe iSCSIOE 2.0.0, EMCVNXe iSCSI OE2.1.0, EMC VNXeiSCSI OE 2.1.1



EMC PowerPath/VE 5.41 See1

Storage Array




EMC PowerPath/VE 5.41 EMC VNXe iSCSIOE 2.0.0

See1



EMC PowerPath/VE: 5.4 SP11, 5.41;

VMware NMP5

EMC VNXe iSCSIOE 2.0.0, EMCVNXe iSCSI OE2.1.0, EMC VNXeiSCSI OE 2.1.1

See1

1. PowerPath/VE 5.4 and 5.4 SP1 for ESX/ESXi 4.0 and Update releases are EOSL as of May 31st 2014. Please contact PowerPath for extended Support.2. EMC supports VMware's recommendations for number of nodes in native ESX cluster configurations.3. For information on VMware VAAI (VMware vStorage APIs for Array Integration) support with EMC storage, and details on array firmware versions that support VAAI please refer to

the Storage/SAN section of the VMware Hardware Compatibility Guide athttp://www.vmware.com/resources/compatibility/search.php.4. For a list of supported guest operating systems, refer tohttp://www.vmware.com/resources/compatibility/search.php?deviceCategory=software. For additional information refer to the

Guest Operating System Installation Guide at http://www.vmware.com/pdf/GuestOS_guide.pdf5. VMware NMP or Native Multipathing is included in the VMware ESX distribution.6. For array installations with VAAI, a mandatory installation of 5.4 SP2 Patch01 required. This patch is available onhttp://PowerLink.emc.com. For further details, please review the

PowerPath/VE for VMware vSphere Release Notes 5.4 and Service Pack Releases document.7. Oracle Database 11g R1 is supported on VMware vSphere 4.0 Virtual Machines with Symmetrix, CLARiiON, and Celerra storage platforms. For details, refer to





VMware ESXiVMware

VMware



Software) Storage Operating Environment Comments


VMware ESXi 4.0(vSphere 4)2, 5, 6


EMC VNXe iSCSI OE 2.0.0 See10


VMware ESXi 4.1(vSphere 4)2, 3, 4, 5, 6, 7, 8,9

EMC PowerPath/VE 5.4 SP21 EMC VNXe iSCSI OE 2.0.0

3 EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300(File/iSCSI)


EMC PowerPath/VE 5.4 SP21 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.0, EMC VNXe iSCSI OE 2.1.1



EMC PowerPath/VE 5.410 See10



EMC PowerPath/VE 5.410 EMC VNXe iSCSI OE 2.0.0 See10



EMC PowerPath/VE: 5.4 SP110,5.410;

VMware NMP11

EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.0, EMC VNXe iSCSI OE 2.1.1

See10



VMware NMP11 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.0, EMC VNXe iSCSI OE 2.1.1


VMware ESXi 5.0(vSphere 5)2, 5, 6, 9, 12

VMware NMP11 EMC VNXe iSCSI OE 2.0.0, EMC VNXe iSCSI OE2.1.0, EMC VNXe iSCSI OE 2.0.0, EMC VNXeiSCSI OE 2.1.1

1. For array installations with VAAI, a mandatory installation of 5.4 SP2 Patch01 required. This patch is available onhttp://PowerLink.emc.com. For further details, please review thePowerPath/VE for VMware vSphere Release Notes 5.4 and Service Pack Releases document.

2. EMC supports VMware's recommendations for number of nodes in native ESX cluster configurations.3. Oracle Database 11g R1 is supported on VMware vSphere 4.0 Virtual Machines with Symmetrix, CLARiiON, and Celerra storage platforms. For details, refer to







10. PowerPath/VE 5.4 and 5.4 SP1 for ESX/ESXi 4.0 and Update releases are EOSL as of May 31st 2014. Please contact PowerPath for extended Support.11. VMware NMP or Native Multipathing is included in the VMware ESX distribution.12. Supports 2-node Microsoft Cluster Services (MSCS) with Windows 2003 and Windows 2008 virtual machines in CIB (Cluster in Box) and CAB (Cluster across Boxes) configurations

for Fibre Channel configurations. VMware NMP (Native Multipathing) and PowerPath/VE are supported with MSCS.

ProvidersConfiguration Notes


Red Hat

No.Information Management

Software Operating System Software Enabler Storage Array

StorageOperating

Environment

Storage Array


1 EMC SMI-S Provider 4.2 Red Hat RHEL [32-Bit]5.5

EMC Solutions Enabler7.2

EMC Unified Storage: VNXe3100 (File/iSCSI),VNXe3300 (File/iSCSI)

EMC VNXeiSCSI OE 2.0.0


Red Hat


Software Operating System Software Enabler Storage ArrayStorage Operating

Environment

1 EMC SMI-S Provider 4.2 Red Hat RHEL [x86_64]:5.5, 6.0

EMC SolutionsEnabler 7.2


EMC VNXe iSCSI OE 2.0.0


SuSE


Software Operating System Software Enabler Storage ArrayStorage Operating

Environment

1 EMC SMI-S Provider 4.2 SuSE SLES [x86_64] 11SP1

EMC SolutionsEnabler 7.2


EMC VNXe iSCSI OE 2.0.0

Replication Manager Block StorageConfiguration Notes

For Replication Manager (RM) with VNX and VNXe Storage:

-RM supports VNXe iSCSI (Windows only).-RM supports Microsoft iSCSI initiator 2.06, 2.07 and 2.08 on Windows 2003.

For Replication Manager (RM) with CLARiiON/VNX Storage:- RM supports iSCSI.- RM supports Microsoft iSCSI initiator 2.06, 2.07 and 2.08 on Windows 2003.

For Replication Manager (RM) with Symmetrix Storage:

-Windows 2003: SPC2 bit is required on production and mount hosts. (Refer to EMC knowledge base solutions emc177815, emc117300 and emc134969 formore details). A microcode hotfix may be needed in some cases, refer to emc113107.-Windows 2008, the following director bits should be set on the FA:Common Serial Number (C)Enable Auto Negotiation (EAN)Enable Pointtopoint (PP)Host SCSI Compliance 2007 (OS2007)SCSI3 SPC2 Compliance (SPC2)Unique World Wide Name (UWN)SCSI3 compliance (SC3)-RM can coexist with SRDF/CE. For details on how to use RM with SRDF/CE, refer to the "EMC Replication Manager and SRDF/CE" whitepaper on Powerlink-RM supports creation of crash consistent pointintime remote clones when the SAP customer is using SRDF/A. Details are contained in EMC Internal-Technical Note "Create Remote SAP TimeFinder/Clones in an SRDF/A Environment with Replication Manager Technical Note (P/N 300008993 Rev A01- RM supports iSCSI.- RM supports Microsoft iSCSI initiator 2.06, 2.07 and 2.08 on Windows 2003.

No. Information Management Software Storage ArrayStorage Operating

Environment1 EMC Replication Manager: 5.3.2, 5.3.3, 5.3.4, 5.4, 5.4.1,

5.4.2EMC Unified Storage: VNXe3100 (File/iSCSI), VNXe3300(File/iSCSI)

EMC VNXe iSCSI OE: 2.0.0, 2.1.0

Veritas Volume ManagerConfiguration Notes

This table describes the support statements for Veritas Volume Manager.


Microsoft

No. Server LVM DMP Operating SystemInfrastructure

Software Storage Array Comments

1 Veritas VxVM 5.1:RP27, 8, SP13, 9, 10,SP2;

Veritas VxVM 5.18

N Microsoft Windows 2003 [x64] DataCenter: R2 SP2, SP2;Microsoft Windows 2003 [x64] Enterprise Edition: R2 SP2,SP2; Microsoft Windows 2003 [x64] Standard Edition: R2SP2, SP2


See1

Storage Array


2 Veritas VxVM 5.1:SP13, 9, 10, SP2


EMC PowerPath: 5.3SP1, 5.34, 5, 6, 11, 5.5


See1

3 Veritas VxVM 5.1:SP19, 10, SP22


Veritas DMP3 EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300 (File/iSCSI)

See1

4 Veritas VxVM: 5.012,13, 14, 15, 16, 17, 5.1RP27, 8, 5.18


EMC PowerPath 5.34, 5,6


See1

1. Hot relocation should be disabled for MSCS cluster configurations.2. Thin Reclaimation using VxVM 5.1 SP2 on VMAX thin devices requires Enginuity 5875 or higher and VxVM hotfix 5.1.20007.873. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".4. PowerPath with Encryption does not support dynamic disks. Please refer to the PowerPath Encryption with RSA Release Notes notes for other features and exceptions5. Support of VSS Provider requires minimum Solution Enabler 7.0.0.06. MPIO-based PowerPath version supports STORPort drivers only for Windows 2003.7. See EMC's Veritas Support Matrix for Veritas Volume Manager support on Microsoft Windows platform8. Statistic Monitoring not supported on a greater than 2 terabyte lun9. FCoE is supported. Requires minimum VxVM 5.1 SP1.

10. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)#emc273310."

11. PowerPath does not support Thin Reclamation.12. Storage Foundation 5.013. STORPort drivers are required with Veritas Storage Foundation 5.0 with EMC Symmetrix arrays if DSM-based DMP multipathing is installed. STORPort driver requires Microsoft

STORPort hotfix Q957910. Please see http://support.microsoft.com/kb/957910. NOTE: Hotfix Q957910 requires a minimum of Service Pack 2 (SP2) to be installed before the hotfixcan be installed.To obtain this hotfix, fill out the hotfix request form at http://support.microsoft.com/hotfix/KBHotfix.aspx?kbnum=957910&kbln=en-us

14. ASL-based DMP multipathing from Veritas Storage Foundation 4.2 or 4.3 is not supported with STORPort drivers. ASL-based DMP is only supported with SCSIPort drivers. IfSTORPort drivers are being used, then only DSM-based DMP or EMC PowerPath can be used for multipath support on Symmetrix arrays.

15. Failover mode 1 required for Veritas multipath solutions (DMP) and CLARiiON storage arrays.16. RP1a for Storage Foundation 5.0 supported.17. Systems that are not running Vertias Volume manager software (VxVM, Foundation Suite, or Storage Foundation) should not move BCV devices to systems that are running Vertias

Volume manager software due to format compatibility issues.


MicrosoftNo. Server LVM DMP Operating System Infrastructure Software Storage Array Comments

1 Veritas VxVM 5.1: RP28,9, SP13, 13, 14, SP2;

Veritas VxVM 5.19

Y5, 6, 7 Microsoft Windows 2003 [x86] DataCenter: R2 SP2, SP2;Microsoft Windows 2003 [x86] Enterprise Edition: R2 SP2,SP2; Microsoft Windows 2003 [x86] Standard Edition: R2 SP2,SP2


See1, 2



Veritas DMP3 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See1, 2

3 Veritas VxVM 5.1: SP13,13, 14, SP2


EMC PowerPath: 5.3 SP1,5.310, 11, 12, 15, 5.5


See1, 2

4 Veritas VxVM: 5.016, 17,18, 19, 20, 21, 5.1 RP28, 9,5.19


EMC PowerPath 5.310, 11,12


See1, 2

1. Hot relocation should be disabled for MSCS cluster configurations.2. PowerPath 4.5.0 is the minimum supported version for Windows 2003 servers with Service Pack 1 (SP1) installed.3. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".4. Thin Reclaimation using VxVM 5.1 SP2 on VMAX thin devices requires Enginuity 5875 or higher and VxVM hotfix 5.1.20007.875. SAN boot is supported with DMP only if external boot is shown as supported in the base connectivity table for the required Server/HBA/OS combination.6. ASL based DMP functionality is not supported with STORPort drivers. ASL based DMP supports SCSIPort (and Emulex SCSU Full Port) drivers only.7. If using DMP features in a MSCS cluster configuration, DMP should be set to Active/Passive mode.8. See EMC's Veritas Support Matrix for Veritas Volume Manager support on Microsoft Windows platform9. Statistic Monitoring not supported on a greater than 2 terabyte lun

10. PowerPath with Encryption does not support dynamic disks. Please refer to the PowerPath Encryption with RSA Release Notes notes for other features and exceptions11. Support of VSS Provider requires minimum Solution Enabler 7.0.0.012. MPIO-based PowerPath version supports STORPort drivers only for Windows 2003.13. FCoE is supported. Requires minimum VxVM 5.1 SP1.14. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."15. PowerPath does not support Thin Reclamation.16. Storage Foundation 5.017. STORPort drivers are required with Veritas Storage Foundation 5.0 with EMC Symmetrix arrays if DSM-based DMP multipathing is installed. STORPort driver requires Microsoft

STORPort hotfix Q957910. Please see http://support.microsoft.com/kb/957910. NOTE: Hotfix Q957910 requires a minimum of Service Pack 2 (SP2) to be installed before the hotfixcan be installed.To obtain this hotfix, fill out the hotfix request form at http://support.microsoft.com/hotfix/KBHotfix.aspx?kbnum=957910&kbln=en-us

18. ASL-based DMP multipathing from Veritas Storage Foundation 4.2 or 4.3 is not supported with STORPort drivers. ASL-based DMP is only supported with SCSIPort drivers. IfSTORPort drivers are being used, then only DSM-based DMP or EMC PowerPath can be used for multipath support on Symmetrix arrays.

19. Failover mode 1 required for Veritas multipath solutions (DMP) and CLARiiON storage arrays.20. RP1a for Storage Foundation 5.0 supported.21. Systems that are not running Vertias Volume manager software (VxVM, Foundation Suite, or Storage Foundation) should not move BCV devices to systems that are running Vertias

Volume manager software due to format compatibility issues.

Microsoft Windows 2008 R2 SP1 [IA64]Microsoft

Storage Array


MicrosoftNo. Server LVM DMP VxFS Operating System Infrastructure Software Storage Array Comments


Veritas VxVM 5.112

N Microsoft Windows 2008 R2 SP1[IA64] for Itanium-Based Systems

EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300 (File/iSCSI)

See4


Veritas VxVM 5.112

N Y Microsoft Windows 2008 R2 SP1[IA64] for Itanium-Based Systems


See14, 15, 16


Veritas VxVM 5.112

Y17 Y8 Microsoft Windows 2008 R2 SP1[IA64] for Itanium-Based Systems


See14, 15, 16


Veritas VxVM 5.112

Y9, 10,11

Microsoft Windows 2008 R2 SP1[IA64] for Itanium-Based Systems


See4, 13



EMC PowerPath: 5.3 SP1,5.31, 2, 3, 5.5


See4



EMC PowerPath: 5.3 SP1,5.5


See14, 15, 16


Y Y8 Microsoft Windows 2008 R2 SP1[IA64] for Itanium-Based Systems

EMC PowerPath 5.31, 2, 3 EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300 (File/iSCSI)



EMC PowerPath: 5.3 SP1,5.5


See14, 15, 16


Y9, 10,11


EMC PowerPath: 5.3 SP1,5.31, 2, 3, 5.5


See4, 13

10 Veritas VxVM 5.1: SP15,6, SP219


Veritas DMP7 EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300 (File/iSCSI)

See4




See14, 15, 16




See14, 15, 16


Y9, 10,11



See4, 13

14 Veritas VxVM: 5.1RP212, 18, 5.112


EMC PowerPath 5.31, 2 EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300 (File/iSCSI)

See4

15 Veritas VxVM: 5.1RP212, 18, 5.112

Y Y8 Microsoft Windows 2008 R2 SP1[IA64] for Itanium-Based Systems


16 Veritas VxVM: 5.1RP212, 18, 5.112

Y9, 10,11



See4, 13

1. PowerPath with Encryption does not support dynamic disks. Please refer to the PowerPath Encryption with RSA Release Notes notes for other features and exceptions2. Support of VSS Provider requires minimum Solution Enabler 7.0.0.03. PowerPath does not support Thin Reclamation.4. Hot relocation should be disabled for MSCS cluster configurations.5. FCoE is supported. Requires minimum VxVM 5.1 SP1.6. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."7. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".8. Supports MP1. MP1 requires RP59. SAN boot is supported with DMP only if external boot is shown as supported in the base connectivity table for the required Server/HBA/OS combination.

10. ASL based DMP functionality is not supported with STORPort drivers. ASL based DMP supports SCSIPort (and Emulex SCSU Full Port) drivers only.11. If using DMP features in a MSCS cluster configuration, DMP should be set to Active/Passive mode.12. Statistic Monitoring not supported on a greater than 2 terabyte lun13. PowerPath 4.5.0 is the minimum supported version for Windows 2003 servers with Service Pack 1 (SP1) installed.14. External VxVM boot is not supported15. VxVM requires the SPC-2 FA director bit enabled, when utilizing Symmetrix LUN addresses greater than 8000. VxVM 4.0 MP3 and above support the SPC-2 FA director bit.16. VxVM 5.0 requires minimum September 06 patch bundle.17. C Bit required for VERITAS VxVM DMP functionality.18. See EMC's Veritas Support Matrix for Veritas Volume Manager support on Microsoft Windows platform19. Thin Reclaimation using VxVM 5.1 SP2 on VMAX thin devices requires Enginuity 5875 or higher and VxVM hotfix 5.1.20007.87


Microsoft

No. Server LVM DMP VxFS Operating SystemInfrastructure



Veritas VxVM: 5.114,6.0

N Microsoft Windows 2008 R2 SP1 [x64]:DataCenter, Enterprise Edition, StandardEdition, Storage Server

EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300(File/iSCSI)

See9



N Y Microsoft Windows 2008 R2 SP1 [x64]:DataCenter, Enterprise Edition, StandardEdition, Storage Server


See2, 3, 4



Y11, 12,13

Microsoft Windows 2008 R2 SP1 [x64]:DataCenter, Enterprise Edition, StandardEdition, Storage Server


See9, 10

Storage Array




Y7 Y8 Microsoft Windows 2008 R2 SP1 [x64]:DataCenter, Enterprise Edition, StandardEdition, Storage Server


See2, 3, 4

5 Veritas VxVM 5.1:SP11, 5, 6, SP2;

Veritas VxVM 6.0


EMC PowerPath: 5.3SP1, 5.5


See9


Veritas VxVM 6.0




See2, 3, 4


Veritas VxVM 6.0

Y11, 12,13




See9, 10


Veritas VxVM 6.0




See2, 3, 4

9 Veritas VxVM 5.1:SP15, 6, SP216;

Veritas VxVM 6.0


Veritas DMP1 EMC Unified Storage: VNXe3100(File/iSCSI), VNXe3300(File/iSCSI)

See9


Veritas VxVM 6.0



See2, 3, 4


Veritas VxVM 6.0

Y11, 12,13



See9, 10


Veritas VxVM 6.0



See2, 3, 4

1. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".2. External VxVM boot is not supported3. VxVM requires the SPC-2 FA director bit enabled, when utilizing Symmetrix LUN addresses greater than 8000. VxVM 4.0 MP3 and above support the SPC-2 FA director bit.4. VxVM 5.0 requires minimum September 06 patch bundle.5. FCoE is supported. Requires minimum VxVM 5.1 SP1.6. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."7. C Bit required for VERITAS VxVM DMP functionality.8. Supports MP1. MP1 requires RP59. Hot relocation should be disabled for MSCS cluster configurations.

10. PowerPath 4.5.0 is the minimum supported version for Windows 2003 servers with Service Pack 1 (SP1) installed.11. SAN boot is supported with DMP only if external boot is shown as supported in the base connectivity table for the required Server/HBA/OS combination.12. ASL based DMP functionality is not supported with STORPort drivers. ASL based DMP supports SCSIPort (and Emulex SCSU Full Port) drivers only.13. If using DMP features in a MSCS cluster configuration, DMP should be set to Active/Passive mode.14. Statistic Monitoring not supported on a greater than 2 terabyte lun15. See EMC's Veritas Support Matrix for Veritas Volume Manager support on Microsoft Windows platform16. Thin Reclaimation using VxVM 5.1 SP2 on VMAX thin devices requires Enginuity 5875 or higher and VxVM hotfix 5.1.20007.87


Microsoft





N Microsoft Windows 2008 R2 [x64]: DataCenter7,8, 9, 13, Enterprise Edition6, 7, 8, 9, StandardEdition6, 7, 8, 9


See11



N Y Microsoft Windows 2008 R2 [x64]: DataCenter7,8, 9, 13, Enterprise Edition6, 7, 8, 9, StandardEdition6, 7, 8, 9


See14, 15, 16



Y1, 2, 3 Microsoft Windows 2008 R2 [x64]: DataCenter7,8, 9, 13, Enterprise Edition6, 7, 8, 9, StandardEdition6, 7, 8, 9


See11, 12



Y18 Y17 Microsoft Windows 2008 R2 [x64]: DataCenter7,8, 9, 13, Enterprise Edition6, 7, 8, 9, StandardEdition6, 7, 8, 9


See14, 15, 16


Veritas VxVM 6.0


EMC PowerPath:5.3 SP1, 5.5


See11


Veritas VxVM 6.0




See14, 15, 16

Storage Array



Veritas VxVM 6.0




See11, 12


Veritas VxVM 6.0




See14, 15, 16


Veritas VxVM 6.0



See11


Veritas VxVM 6.0



See14, 15, 16


Veritas VxVM 6.0



See11, 12


Veritas VxVM 6.0



See14, 15, 16

1. SAN boot is supported with DMP only if external boot is shown as supported in the base connectivity table for the required Server/HBA/OS combination.2. ASL based DMP functionality is not supported with STORPort drivers. ASL based DMP supports SCSIPort (and Emulex SCSU Full Port) drivers only.3. If using DMP features in a MSCS cluster configuration, DMP should be set to Active/Passive mode.4. FCoE is supported. Requires minimum VxVM 5.1 SP1.5. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."6. When Windows Hyper-V is enabled and supporting child (guest) operating systems, minimum PowerPath/VE 5.3 is supported on the parent server.7. Windows Server Core installation option is supported.8. Windows Server Core installation option is supported by EMC. Contact your server vendor to determine their support statement for Server Core.9. Microsoft Hyper-V for Windows 2008 and 2008 R2 Server is supported. EMC supports only the GA-version of Hyper-V, located at

http://www.microsoft.com/windowsserver2008/en/us/hyperv-main.aspx.Supported guest Operating systems are Windows 2003 server SP2 x86/x64, Windows 2008 server x86/x64 SP1/SP2, and Windows 2008 R2.

10. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".11. Hot relocation should be disabled for MSCS cluster configurations.12. PowerPath 4.5.0 is the minimum supported version for Windows 2003 servers with Service Pack 1 (SP1) installed.13. Windows Server Core installation option supported.14. External VxVM boot is not supported15. VxVM requires the SPC-2 FA director bit enabled, when utilizing Symmetrix LUN addresses greater than 8000. VxVM 4.0 MP3 and above support the SPC-2 FA director bit.16. VxVM 5.0 requires minimum September 06 patch bundle.17. Supports MP1. MP1 requires RP518. C Bit required for VERITAS VxVM DMP functionality.19. Thin Reclaimation using VxVM 5.1 SP2 on VMAX thin devices requires Enginuity 5875 or higher and VxVM hotfix 5.1.20007.8720. Statistic Monitoring not supported on a greater than 2 terabyte lun21. See EMC's Veritas Support Matrix for Veritas Volume Manager support on Microsoft Windows platform


Microsoft



1 Veritas VxVM 5.1:RP24, 19, SP115, 17,18, SP2;


N Microsoft Windows 2008 [x64]: DataCenter,DataCenter SP2, Enterprise Edition, EnterpriseEdition SP2, Standard Edition, Standard EditionSP2


See10



N Y Microsoft Windows 2008 [x64]: DataCenter,DataCenter SP2, Enterprise Edition, EnterpriseEdition SP2, Standard Edition, Standard EditionSP2


See1, 2, 3



Y13 Y12 Microsoft Windows 2008 [x64]: DataCenter,DataCenter SP2, Enterprise Edition, EnterpriseEdition SP2, Standard Edition, Standard EditionSP2


See1, 2, 3



Y7, 8, 9 Microsoft Windows 2008 [x64]: DataCenter,DataCenter SP2, Enterprise Edition, EnterpriseEdition SP2, Standard Edition, Standard EditionSP2


See10, 11


Veritas VxVM 6.0


EMC PowerPath: 5.3SP1, 5.35, 6, 16, 5.5


See10


Veritas VxVM 6.0




See1, 2, 3


Veritas VxVM 6.0

Y Y12 Microsoft Windows 2008 [x64]: DataCenter,DataCenter SP2, Enterprise Edition, EnterpriseEdition SP2, Standard Edition, Standard EditionSP2

EMC PowerPath 5.35,6, 16



Veritas VxVM 6.0




See1, 2, 3

Storage Array



Veritas VxVM 6.0


EMC PowerPath: 5.3SP1, 5.35, 6, 16, 5.5


See10, 11


Veritas VxVM 6.0



See10


Veritas VxVM 6.0



See1, 2, 3


Veritas VxVM 6.0



See1, 2, 3


Veritas VxVM 6.0



See10, 11

14 Veritas VxVM: 5.1RP24, 19, 5.14


EMC PowerPath 5.35, 6 EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300 (File/iSCSI)

See10

15 Veritas VxVM: 5.1RP24, 19, 5.14



16 Veritas VxVM: 5.1RP24, 19, 5.14



See10, 11

1. External VxVM boot is not supported2. VxVM requires the SPC-2 FA director bit enabled, when utilizing Symmetrix LUN addresses greater than 8000. VxVM 4.0 MP3 and above support the SPC-2 FA director bit.3. VxVM 5.0 requires minimum September 06 patch bundle.4. Statistic Monitoring not supported on a greater than 2 terabyte lun5. PowerPath with Encryption does not support dynamic disks. Please refer to the PowerPath Encryption with RSA Release Notes notes for other features and exceptions6. Support of VSS Provider requires minimum Solution Enabler 7.0.0.07. SAN boot is supported with DMP only if external boot is shown as supported in the base connectivity table for the required Server/HBA/OS combination.8. ASL based DMP functionality is not supported with STORPort drivers. ASL based DMP supports SCSIPort (and Emulex SCSU Full Port) drivers only.9. If using DMP features in a MSCS cluster configuration, DMP should be set to Active/Passive mode.

10. Hot relocation should be disabled for MSCS cluster configurations.11. PowerPath 4.5.0 is the minimum supported version for Windows 2003 servers with Service Pack 1 (SP1) installed.12. Supports MP1. MP1 requires RP513. C Bit required for VERITAS VxVM DMP functionality.14. Thin Reclaimation using VxVM 5.1 SP2 on VMAX thin devices requires Enginuity 5875 or higher and VxVM hotfix 5.1.20007.8715. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".16. PowerPath does not support Thin Reclamation.17. FCoE is supported. Requires minimum VxVM 5.1 SP1.18. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."19. See EMC's Veritas Support Matrix for Veritas Volume Manager support on Microsoft Windows platform


Microsoft




Veritas VxVM 5.14



See5


Veritas VxVM 5.14



See10, 11, 12


Veritas VxVM 5.14



See5, 6


Veritas VxVM 5.14



See10, 11, 12



EMC PowerPath: 5.3SP1, 5.37, 8, 16, 5.5


See5





See10, 11, 12



EMC PowerPath 5.37,8, 16




EMC PowerPath: 5.3SP1, 5.37, 8, 16, 5.5


See5, 6

Storage Array






See10, 11, 12




See5




See10, 11, 12




See5, 6




See10, 11, 12

14 Veritas VxVM: 5.1RP24, 19, 5.14



See5

15 Veritas VxVM: 5.1RP24, 19, 5.14



16 Veritas VxVM: 5.1RP24, 19, 5.14



See5, 6

1. SAN boot is supported with DMP only if external boot is shown as supported in the base connectivity table for the required Server/HBA/OS combination.2. ASL based DMP functionality is not supported with STORPort drivers. ASL based DMP supports SCSIPort (and Emulex SCSU Full Port) drivers only.3. If using DMP features in a MSCS cluster configuration, DMP should be set to Active/Passive mode.4. Statistic Monitoring not supported on a greater than 2 terabyte lun5. Hot relocation should be disabled for MSCS cluster configurations.6. PowerPath 4.5.0 is the minimum supported version for Windows 2003 servers with Service Pack 1 (SP1) installed.7. PowerPath with Encryption does not support dynamic disks. Please refer to the PowerPath Encryption with RSA Release Notes notes for other features and exceptions8. Support of VSS Provider requires minimum Solution Enabler 7.0.0.09. Supports MP1. MP1 requires RP5

10. External VxVM boot is not supported11. VxVM requires the SPC-2 FA director bit enabled, when utilizing Symmetrix LUN addresses greater than 8000. VxVM 4.0 MP3 and above support the SPC-2 FA director bit.12. VxVM 5.0 requires minimum September 06 patch bundle.13. C Bit required for VERITAS VxVM DMP functionality.14. Thin Reclaimation using VxVM 5.1 SP2 on VMAX thin devices requires Enginuity 5875 or higher and VxVM hotfix 5.1.20007.8715. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".16. PowerPath does not support Thin Reclamation.17. FCoE is supported. Requires minimum VxVM 5.1 SP1.18. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."19. See EMC's Veritas Support Matrix for Veritas Volume Manager support on Microsoft Windows platform


OracleNo. Server LVM DMP VxFS Operating System Infrastructure Software Storage Array Comments

1 Veritas VxVM 6.0 Y Oracle Linux [x86_64] 5.71 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See2, 3

2 Veritas VxVM 6.0 Y Oracle Linux [x86_64] 5.71 Veritas DMP EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See2, 3

3 Veritas VxVM 6.0 N Y Oracle Linux [x86_64] 5.71 EMC PowerPath 5.6 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See2, 3

1. Supported kernels: 2.6.18-274.0.0.0.1.el5, 2.6.18-274.12.1.0.1.el5, 2.6.18-274.17.1.0.1.el5. Confirm kernel support with server vendor.2. VxVM "Thin Reclamation" functionality is not supported with PowerPath.3. FCoE is supported. Requires minimum VxVM 5.1


OracleNo. Server LVM DMP VxFS Operating System Infrastructure Software Storage Array Comments

1 Veritas VxVM 5.1 SP15, 7, 8, 9, 13, 14,20, 21

Y Y22 Oracle Solaris 10SPARC15, 16

EMC PowerPath: 5.3 P024,5.54;

Veritas DMP

EMC Unified Storage VNXe3300(File/iSCSI)

See11

Storage Array


2 Veritas VxVM 5.1 SP1_x645, 6, 7, 8, 9 Y7 Y10 Oracle Solaris 10 x862, 3 EMC PowerPath: 5.3 P024,5.54;

Veritas DMP


See1

3 Veritas VxVM 5.17, 8, 9, 24 Y Y23 Oracle Solaris 10SPARC15, 16


Veritas DMP


See11

4 Veritas VxVM 5.1_x645, 8, 9, 19 Y7 Y18 Oracle Solaris 10 x862, 3 EMC PowerPath: 5.3 P024,5.54;

Veritas DMP


See1

5 Veritas VxVM 6.0 PR15, 8, 9, 13, 14 Y Y28 Oracle Solaris 11SPARC27

EMC PowerPath 5.54;Veritas DMP


See11

6 Veritas VxVM 6.05, 8, 9, 12, 13, 14 Y Y17 Oracle Solaris 10SPARC15, 16


Veritas DMP


See11

7 Veritas VxVM 6.0_x64 PR15, 8, 9, 14 Y Y25 Oracle Solaris 11 x8626 EMC PowerPath 5.54;Veritas DMP


8 Veritas VxVM 6.0_x647, 8, 9, 30 Y Y29 Oracle Solaris 10 x862, 3 EMC PowerPath: 5.3 P024,5.54;

Veritas DMP


1. FCoE is supported. Requires minimum VxVM 5.1_x642. Requires Solaris x86 10 Update 2 (06/06) or later.3. EMC supports ZFS in Solaris 10_x86 11/06 (update 3) or later. The Snapshot and Clone features of ZFS are supported only through Sun Microsystems.4. PowerPath is supported with CLARiiON failover mode set to 1 and 45. The SPC2 flag must be enabled for support of > 8k devices.6. VxVM 5.1 SP1_x64 supports RP1 and RP2.7. DMP is supported with CLARiiON failover mode set to 1 and 4 where applicable.8. Host based Thin Reclamation using Veritas Storage Foundation is currently not supported with Symmetrix SRDF volumes9. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".

10. VxFS 5.1 SP1_x64 supports RP1 and RP2.11. FCoE is supported. Requires minimum VxVM 5.112. Supports VxVM 6.0 with RP1.13. Requires minimum DMX microcode revision 5671.59.64 or 5670.98.89 for DMX/DMX-2, and 5771.87.95 for DMX-3.14. DMP is supported with CLARiiON failover mode set to 1 and 4 (ALUA mode).15. For LDOM support, please refer to the 'Virtualization Server Support' table available via EMC PowerLink:

https://elabnavigator.emc.com/emcpubs/elab/esm/pdf/Virtualization_Server_Support.pdf16. The Snapshot and Clone features of ZFS are supported only through Oracle Corporation.17. Supports VxFS 6.0 with RP1.18. VxFS 5.1_x64 supports RP1 and RP2.19. VxVM 5.1_x64 supports RP1 and RP2.20. VxVM 5.1 SP1 supports RP1 and RP2.21. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."22. VxFS 5.1 SP1 supports RP1 and RP2.23. VxFS 5.1 supports RP1 and RP2.24. VxVM 5.1 supports RP1 and RP2.25. Support VxFS 6.0_x64 PR126. EMC recommends as a best practice that customers upgrade to the most recent Solaris 11 x86 SRU released on the Oracle website:http://support.oracle.com27. EMC recommends as a best practice that customers upgrade to the most recent Solaris 11 SPARC SRU released on the Oracle website:http://support.oracle.com28. Supports VxFS 6.0 PR129. Support VxFS 6.0_x64 with RP1.30. Support VxVM 6.0_x64 with RP1.


Red HatNo. Server LVM DMP VxFS Operating System Infrastructure Software Storage Array Comments

1 Veritas VxVM 5.0 MP4 Y1 Y Red Hat RHEL [x86_64] 5.52 EMC PowerPath 5.5 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

2 Veritas VxVM 5.1 SP1 PR2 Y Red Hat RHEL [x86_64] 6.03 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

3 Veritas VxVM 5.1 SP1 PR2 Y Red Hat RHEL [x86_64] 6.03 EMC PowerPath 5.6;Veritas DMP


See4, 5

4 Veritas VxVM 5.1 SP1 PR2 Y Y Red Hat RHEL [x86_64] 6.03 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

5 Veritas VxVM 5.1 SP1 PR2 Y Y Red Hat RHEL [x86_64] 6.03 Veritas DMP EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

6 Veritas VxVM 5.1 SP11, 14, 15, 16,17, 18

Y1 Y Red Hat RHEL [x86_64] 5.52 EMC PowerPath: 5.5, 5.6 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

Storage Array


7 Veritas VxVM 6.0 Y Red Hat RHEL [x86_64] 6.29, 10,11, 12, 13


See4, 5

8 Veritas VxVM 6.0 Y Red Hat RHEL [x86_64] 6.29, 10,11, 12, 13

EMC PowerPath 5.6;Veritas DMP


See4, 5

9 Veritas VxVM 6.0 Y Y Red Hat RHEL [x86_64] 6.29, 10,11, 12, 13


See4, 5

10 Veritas VxVM 6.0 Y Y Red Hat RHEL [x86_64] 6.29, 10,11, 12, 13

Veritas DMP EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

11 Veritas VxVM 6.0 Y1 Y Red Hat RHEL [x86_64] 5.66 Veritas DMP EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

12 Veritas VxVM: 5.1 SP1 PR2, 6.0 Y Red Hat RHEL [x86_64]: 5.77, 6.18 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

13 Veritas VxVM: 5.1 SP1 PR2, 6.0 Y Red Hat RHEL [x86_64]: 5.77, 6.18 EMC PowerPath 5.6;Veritas DMP


See4, 5

14 Veritas VxVM: 5.1 SP1 PR2, 6.0 Y Y Red Hat RHEL [x86_64] 6.18 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

15 Veritas VxVM: 5.1 SP1 PR2, 6.0 Y Y Red Hat RHEL [x86_64] 6.18 Veritas DMP EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

16 Veritas VxVM: 5.1 SP11, 14, 15, 16,17, 18, 6.0

Y1 Y Red Hat RHEL [x86_64] 5.66 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

17 Veritas VxVM: 5.1 SP11, 14, 15, 16,17, 18, 6.0

Y1 Y Red Hat RHEL [x86_64] 5.66 EMC PowerPath 5.6 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See4, 5

1. DMP is supported with CLARiiON failover mode set to 1 and 4 where applicable.2. Supported kernels: 2.6.18-194.el5, 2.6.18-194.3.1.el5, 2.6.18-194.8.1.el5, 2.6.18-194.11.1.el5, 2.6.18-194.11.3.el5, 2.6.18-194.11.4.el5, 2.6.18-194.17.1.el5, 2.6.18-194.17.4.el5,

2.6.18-194.26.1.el5, 2.6.18-194.32.1.el5 Confirm kernel support with server vendor.3. Supported kernels: 2.6.32-71.el6, 2.6.32-71.7.1.el6, 2.6.32-71.14.1.el6, 2.6.32-71.18.1.el6, 2.6.32-71.18.2.el6, 2.6.32-71.24.1.el6, 2.6.32-71.31.1.el6, 2.6.32-71.34.1.el6,

2.6.32-71.36.1.el6, 2.6.32-71.37.1.el6, 2.6.32-71.38.1.el6. Confirm kernel support with server vendor.4. VxVM "Thin Reclamation" functionality is not supported with PowerPath.5. FCoE is supported. Requires minimum VxVM 5.16. Supported kernels: 2.6.18-238.el5, 2.6.18-238.1.1.el5, 2.6.18-238.5.1.el5, 2.6.18-238.9.1.el5, 2.6.18-238.12.1.el5, 2.6.18-238.19.1.el5, 2.6.18-238.21.1.el5, 2.6.18-238.27.1.el5,

2.6.18-238.28.1.el5, 2.6.18-238.31.1.el5, 2.6.18-238.33.1.el5, 2.6.18-238.35.1.el5, 2.6.18-238.37.1.el5. Confirm kernel support with server vendor.7. Supported kernels: 2.6.18-274.el5, 2.6.18-274.3.1el5, 2.6.18-274.7.1.el5, 2.6.18-274.12.1.el5, 2.6.18-274.17.1.el5, 2.6.18-274.18.1.el5. Confirm kernel support with server vendor.8. Supported kernels: 2.6.32-131.0.15.el6, 2.6.32-131.2.1.el6, 2.6.32-131.6.1.el6, 2.6.32-131.12.1.el6, 2.6.32-131.17.1.el6, 2.6.32-131.21.1.el6, 2.6.32-131.25.1.el6. Confirm kernel

support with server vendor.9. The LVM included as part of this update is supported and can be used in conjunction with PowerPath emcpower pseudo device file names as well as native sd device file names.



12. Native multipathing is supported on boot-from-SAN configurations. Please refer to the operating system vendor's documentation for installation instructions. Also refer to the EMCHost Connectivity Guide for Linux found on http://powerlink.emc.com for any additional guidance.

13. RHEL KVM is supported but not with EMC PowerPath. Refer to the Virtualiztion Hosting Server (Parent) Solutions table for supported configurations.14. The SPC2 flag must be enabled for support of > 8k devices.15. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)

#emc273310."16. Requires minimum DMX microcode revision 5671.59.64 or 5670.98.89 for DMX/DMX-2, and 5771.87.95 for DMX-3.17. EMC supports stand-alone DMP failover functionality, for the purposes of controlling non-VxVM volume managers. Support requires Storage Foundation 5.1 SP1 or later. Please

check the appropriate Host Connectivity Guide for more information regarding native LVM.18. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".


Storage Array


SuSENo. Server LVM DMP VxFS Operating System Infrastructure Software Storage Array Comments

1 Veritas VxVM 5.1 SP19, 10, 11,12, 13, 14

Y11 Y SuSE SLES [x86_64] 11 SP17, 8 EMC PowerPath 5.5 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See1, 2

2 Veritas VxVM 6.0 Y SuSE SLES [x86_64] 11 SP17, 8 EMC PowerPath 5.5 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See1, 2

3 Veritas VxVM 6.0 Y SuSE SLES [x86_64]: 10 SP43, 4, 5, 6,11 SP17, 8


See1, 2

4 Veritas VxVM 6.0 Y SuSE SLES [x86_64]: 10 SP43, 4, 5, 6,11 SP17, 8

Veritas DMP EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See1, 2

5 Veritas VxVM 6.0 N Y SuSE SLES [x86_64] 10 SP43, 4, 5, 6 EMC PowerPath 5.5 P01 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See1, 2

6 Veritas VxVM 6.0 Y Y SuSE SLES [x86_64] 10 SP43, 4, 5, 6 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See1, 2

7 Veritas VxVM 6.0 Y Y SuSE SLES [x86_64] 10 SP43, 4, 5, 6 Veritas DMP EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

See1, 2

1. VxVM "Thin Reclamation" functionality is not supported with PowerPath.2. FCoE is supported. Requires minimum VxVM 5.13. Supported kernels: 2.6.16.60-0.85.1, 2.6.16.60-0.87.1, 2.6.16.60-0.89.1, 2.6.16.60-0.91.1, 2.6.16.60-0.93.1. Confirm kernel support with server vendor.4. Novell OES 2 SP2 is supported with this update.5. Novell OES is only supported with Fibre channel connectivity.6. Novell OES 2 SP3 is supported with this update.7. Novell OES 11 is supported with this update.8. Supported kernels: 2.6.32.12-0.7, 2.6.32.13-0.4.1, 2.6.32.13-0.5.1, 2.6.32.19-0.2.1, 2.6.32.19-0.3.1, 2.6.32.23-0.3.1, 2.6.32.24-0.2, 2.6.32.27-0.2.2, 2.6.32.29-0.3.1, 2.6.32.36-0.5.2,

2.6.32.43-0.4.1, 2.6.32.45-0.3.2, 2.6.32.46-0.3.1, 2.6.32.49-0.3.1, 2.6.32.54-0.3. Confirm kernel support with server vendor.9. The SPC2 flag must be enabled for support of > 8k devices.

10. "Refer to Symantec Knowledge base http://www.symantec.com/docs/TECH164343 for a required/recommended fix. Also documented in EMC Knowledge Base (Primus)#emc273310."

11. DMP is supported with CLARiiON failover mode set to 1 and 4 where applicable.12. Requires minimum DMX microcode revision 5671.59.64 or 5670.98.89 for DMX/DMX-2, and 5771.87.95 for DMX-3.13. EMC supports stand-alone DMP failover functionality, for the purposes of controlling non-VxVM volume managers. Support requires Storage Foundation 5.1 SP1 or later. Please

check the appropriate Host Connectivity Guide for more information regarding native LVM.14. Please refer to the Host Connectivity Guide of each respective operating system platform for additional information regarding VxVM functionality, such as "Thin Reclamation".

WAN Optimization ControllersConfiguration Notes

Most devices in the IP cloud that follow IEEE standards may be used for LAN/MAN/WAN connectivity within EMC replication networks. WAN optimizationcontrollers, however, must be explicitly listed as supported in the EMC Support Matrix table below if used in EMC replication networks. WAN optimizationcontrollers are devices that employ protocol optimization techniques with the TCP/IP protocol to improve latency and performance over IP networks.

All EMC replication solutions over IP networks must also be validated using the Solution Qualifier (SQ) process and must undergo a Network Assessment.

EDL/CDL, Centera Replicator and Open Replicator are not currently supported by EMC for use with WAN optimization controllers. For these and any otherapplications not referenced by this EMC Support Matrix table, support is the responsibility of the customer and WAN optimization controller vendor.

All EMC replication solutions over IP networks must also be validated using the Solution Qualifier (SQ) process.

No. WAN Optimization ControllerSupported LinkSpeed (Gbps)

CodeLevel Topology Network

DistanceProtocol Storage Array

1 Riverbed Steelhead: 0501-H, 0501-M, 0601,1050, 2050, 250, 5050, 5050-H, 5050-L, 5050-M,550, 6050

1 6.1.1a Network: IP IP Replicator2 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

2 Riverbed Steelhead: 0501-H, 0501-M, 0601,5050, 5050-H, 5050-L, 5050-M, 6050

1 6.1.3a1 Network: IP IP RecoverPoint;Replicator


Storage Array


3 Riverbed Steelhead: 1050, 2050; Riverbed VirtualSteelhead: V1050-H, V1050-L, V1050-M,V2050-H, V2050-L, V2050-M

1 6.1.3a Network: IP IP RecoverPoint;Replicator


4 Riverbed Steelhead: 701, 7050 1; 10 6.1.1a Network: IP IP Replicator2 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

5 Riverbed Steelhead: 701, 7050 1; 10 6.1.3a1 Network: IP IP RecoverPoint;Replicator


6 Riverbed Virtual Steelhead: V1050-H, V1050-L,V1050-M, V2050-H, V2050-L, V2050-M

1 6.1.1-vsh Network: IP IP Replicator2 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

7 Riverbed: CX1555H, CX1555L, CX1555M,CX755H, CX755L, CX755M

1 6.5.4 Network: IP IP RecoverPoint EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

8 Silver Peak: NX-1700, NX-2600, NX-2610,NX-3500, NX-5700, NX-7700, NX-8700,NX-9700, VX-1000, VX-2000, VX-5000

1 3.3.1 Network: IP IP Replicator2 EMC UnifiedStorage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)

9 Silver Peak: NX-1700, NX-5700, NX-7700,VRX-8, VX-1000, VX-2000, VX-3000, VX-5000

1 4.1.0 Network: IP IP RecoverPoint;Replicator


10 Silver Peak: NX-8700, NX-9700 1; 10 4.1.0 Network: IP IP RecoverPoint;Replicator


1. With Riverbed firmware 6.1.3a and above, the SRDF Selective Optimization feature is supported for SRDF group level optimization for end-to-end GigE environments with VMAXwhich have Microcode level 5875 and above.

2. "Unified Storage VNX5300/5500/5700/7500" are supported for File Implementations.

iSCSI ClustersConfiguration Notes

This table describes the support statements for iSCSI Clusters.


Microsoft

No. Operating SystemCluster

Software Host Bus Adapter Storage Array

Max #Nodes:

HA Comments

1 Microsoft Windows2003 [x64] EnterpriseEdition: R2 SP2, SP2

MicrosoftMSCS1, 2, 3, 4

Emulex: OCe10102-IM-E, OCe10102-IX-E;

Generic Vendor NIC: 10GbE4, 12, 17, GbE4, 12, 17, 18


8 See5, 6, 7, 15

2 Microsoft Windows2003 [x64] EnterpriseEdition: R2 SP2, SP2


QLogic: QLA4050-E-SP4, 8, 9, 10, 11, 12, 13, 14, 16, QLA4050C-E-SP4,8, 9, 10, 11, 12, 13, 14, 16, QLA4052C-E-SP4, 8, 9, 10, 11, 12, 13, 14, 16,QLE4060C-E-SP4, 8, 9, 10, 11, 12, 13, 14, QLE4062C-E-SP4, 8, 9, 10, 11,12, 13, 14


8 See5, 6, 7

1. Microsoft Cluster Server (MSCS) in iSCSI supports minimum R26 Flare release version xx.26.xxx.5.007.2. Booting from external storage for iSCSI clusters is not supported.3. Microsoft iSCSI Initiator required. Refer to Native iSCSI table for currently supported initiator version.4. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)5. iSCSI based cluster configurations require Microsoft QFE 824354. Please contact Microsoft Product Support Services for this QFE.6. Booting from external array is supported for iSCSI clusters with QLA4010 iSCSI HBAs. Refer to Native iSCSI table for supported BIOS versions.7. Microsoft Dynamic Disks are not supported.8. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.9. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com

10. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.11. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.12. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)13. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.14. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.15. EMC provides troubleshooting and other technical notes for MSCS cluster solutions. Visit EMC Powerlink and download part number 300-000-603 for the EMC Host Connectivity

Guide for Windows.16. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator.17. MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later.18. Any Microsoft supported server/NIC for the listed operating system revision is supported.


Storage Array


Microsoft



Max #Nodes:

HA Comments

1 Microsoft Windows2003 [x86] DataCenter:R2 SP2, SP2;

Microsoft Windows2003 [x86] EnterpriseEdition: R2 SP2, SP2

MicrosoftMSCS1, 2, 3

IBM QLogic iSCSI Exp Card for BladeCenter (26K6487)11, 14, 16 EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300 (File/iSCSI)

8 See5, 6, 7





Generic Vendor NIC: 10GbE4, 12, 17, GbE4, 12, 17, 18


8 See5, 6, 7, 15




QLogic: QLA4050-E-SP4, 8, 9, 10, 11, 12, 13, 14, 16,QLA4050C-E-SP4, 8, 9, 10, 11, 12, 13, 14, 16, QLA4052C-E-SP4, 8, 9,10, 11, 12, 13, 14, 16, QLE4060C-E-SP4, 8, 9, 10, 11, 12, 13, 14,QLE4062C-E-SP4, 8, 9, 10, 11, 12, 13, 14


8 See5, 6, 7



Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.12. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)13. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.14. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.15. EMC provides troubleshooting and other technical notes for MSCS cluster solutions. Visit EMC Powerlink and download part number 300-000-603 for the EMC Host Connectivity

Guide for Windows.16. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software



Microsoft



Max #Nodes:

HA Comments

1 Microsoft Windows 2008R2 SP1 [x64]:DataCenter, EnterpriseEdition, Standard Edition

MicrosoftFailoverClustering1, 2,3, 4


Generic Vendor NIC: 10GbE4, 12, 17, GbE12, 17, 18

EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300(File/iSCSI)15

16 See5, 6, 7, 16

2 Microsoft Windows 2008R2 SP1 [x64]:DataCenter, EnterpriseEdition, Standard Edition


QLogic: QLA4010-E-SP4, 10, 11, 12, 19, QLA4010C-E-SP4, 10, 11,12, 19, QLA4050-E-SP4, 8, 9, 10, 11, 12, 13, 14, 19, QLA4050C-E-SP4,8, 9, 10, 11, 12, 13, 14, 19, QLA4052C-E-SP4, 8, 9, 10, 11, 12, 13, 14, 19,QLE4060C-E-SP4, 8, 9, 10, 11, 12, 13, 14, QLE4062C-E-SP4, 8, 9, 10,11, 12, 13, 14

EMC Unified Storage:VNXe3100 (File/iSCSI),VNXe3300(File/iSCSI)15

16 See5, 6, 7



Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.12. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)13. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.14. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.15. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" Quorum

Configuration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."16. EMC provides troubleshooting and other technical notes for MSCS cluster solutions. Visit EMC Powerlink and download part number 300-000-603 for the EMC Host Connectivity

Guide for Windows.17. MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later.18. Any Microsoft supported server/NIC for the listed operating system revision is supported.19. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator.


Microsoft



Max #Nodes:

HA Comments

Storage Array


1 Microsoft Windows 2008 R2[x64]: DataCenter13, 14, 15,17, Enterprise Edition12, 13,14, 15, Standard Edition12, 13,14, 15




EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)16

16 See5, 6, 7, 8

2 Microsoft Windows 2008 R2[x64]: DataCenter13, 14, 15,17, Enterprise Edition12, 13,14, 15, Standard Edition12, 13,14, 15


QLogic: QLA4010-E-SP4, 11, 20, 21, 24, QLA4010C-E-SP4, 11, 20,21, 24, QLA4050-E-SP4, 11, 18, 19, 20, 21, 22, 23, 24,QLA4050C-E-SP4, 11, 18, 19, 20, 21, 22, 23, 24, QLA4052C-E-SP4,11, 18, 19, 20, 21, 22, 23, 24, QLE4060C-E-SP4, 11, 18, 19, 20, 21, 22,23, QLE4062C-E-SP4, 11, 18, 19, 20, 21, 22, 23


16 See6, 7, 8

1. Microsoft Cluster Server (MSCS) in iSCSI supports minimum R26 Flare release version xx.26.xxx.5.007.2. Booting from external storage for iSCSI clusters is not supported.3. Microsoft iSCSI Initiator required. Refer to Native iSCSI table for currently supported initiator version.4. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)5. EMC provides troubleshooting and other technical notes for MSCS cluster solutions. Visit EMC Powerlink and download part number 300-000-603 for the EMC Host Connectivity

Guide for Windows.6. iSCSI based cluster configurations require Microsoft QFE 824354. Please contact Microsoft Product Support Services for this QFE.7. Booting from external array is supported for iSCSI clusters with QLA4010 iSCSI HBAs. Refer to Native iSCSI table for supported BIOS versions.8. Microsoft Dynamic Disks are not supported.9. MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later.

10. Any Microsoft supported server/NIC for the listed operating system revision is supported.11. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)12. When Windows Hyper-V is enabled and supporting child (guest) operating systems, minimum PowerPath/VE 5.3 is supported on the parent server.13. Windows Server Core installation option is supported.14. Windows Server Core installation option is supported by EMC. Contact your server vendor to determine their support statement for Server Core.15. Microsoft Hyper-V for Windows 2008 and 2008 R2 Server is supported. EMC supports only the GA-version of Hyper-V, located at

http://www.microsoft.com/windowsserver2008/en/us/hyperv-main.aspx.Supported guest Operating systems are Windows 2003 server SP2 x86/x64, Windows 2008 server x86/x64 SP1/SP2, and Windows 2008 R2.


17. Windows Server Core installation option supported.18. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.19. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com20. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.21. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.22. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.23. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.24. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator.


Microsoft



Max #Nodes:

HA Comments

1 Microsoft Windows 2008 [x64]Standard: Edition, Edition SP2


Emulex: OCe10102-IM-E, OCe10102-IX-E EMC Unified Storage:VNXe3100(File/iSCSI),VNXe3300(File/iSCSI)13

16 See6, 7, 8




8 See6, 7, 8

3 Microsoft Windows 2008 [x64]:DataCenter SP212,DataCenter12, Enterprise EditionSP212, Enterprise Edition12





16 See5, 6, 7, 8

4 Microsoft Windows 2008 [x64]:DataCenter SP212,DataCenter12, Enterprise EditionSP212, Enterprise Edition12





8 See5, 6, 7, 8

5 Microsoft Windows 2008 [x64]:DataCenter SP212,DataCenter12, Enterprise EditionSP212, Enterprise Edition12,Standard Edition, StandardEdition SP2


QLogic: QLA4010-E-SP4, 11, 16, 17, 20, QLA4010C-E-SP4, 11,16, 17, 20, QLA4050-E-SP4, 11, 14, 15, 16, 17, 18, 19, 20,QLA4050C-E-SP4, 11, 14, 15, 16, 17, 18, 19, 20,QLA4052C-E-SP4, 11, 14, 15, 16, 17, 18, 19, 20,QLE4060C-E-SP4, 11, 14, 15, 16, 17, 18, 19, QLE4062C-E-SP4,11, 14, 15, 16, 17, 18, 19


16 See6, 7, 8

6 Microsoft Windows 2008 [x64]:DataCenter SP212,DataCenter12, Enterprise EditionSP212, Enterprise Edition12,Standard Edition, StandardEdition SP2




8 See6, 7, 8

1. Microsoft Cluster Server (MSCS) in iSCSI supports minimum R26 Flare release version xx.26.xxx.5.007.2. Booting from external storage for iSCSI clusters is not supported.3. Microsoft iSCSI Initiator required. Refer to Native iSCSI table for currently supported initiator version.4. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)5. EMC provides troubleshooting and other technical notes for MSCS cluster solutions. Visit EMC Powerlink and download part number 300-000-603 for the EMC Host Connectivity

Guide for Windows.6. iSCSI based cluster configurations require Microsoft QFE 824354. Please contact Microsoft Product Support Services for this QFE.7. Booting from external array is supported for iSCSI clusters with QLA4010 iSCSI HBAs. Refer to Native iSCSI table for supported BIOS versions.8. Microsoft Dynamic Disks are not supported.9. MS iSCSI Initiator 2.08 only supports PowerPath 5.2 or later.

10. Any Microsoft supported server/NIC for the listed operating system revision is supported.11. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)12. Windows Server Core installation option is supported by EMC. Contact your server vendor to determine their support statement for Server Core.13. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" Quorum

Configuration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."14. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.15. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com16. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.17. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.18. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.19. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.20. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator.

Storage Array



Microsoft



Max #Nodes:

HA Comments




16 See5, 6, 7




8 See5, 6, 7

3 Microsoft Windows 2008 [x86]:DataCenter SP28, DataCenter8,Enterprise Edition SP28,Enterprise Edition8





16 See5, 6, 7, 10

4 Microsoft Windows 2008 [x86]:DataCenter SP28, DataCenter8,Enterprise Edition SP28,Enterprise Edition8





8 See5, 6, 7, 10

5 Microsoft Windows 2008 [x86]:DataCenter SP28, DataCenter8,Enterprise Edition SP28,Enterprise Edition8, StandardEdition, Standard Edition SP28




16 See5, 6, 7

6 Microsoft Windows 2008 [x86]:DataCenter SP28, DataCenter8,Enterprise Edition SP28,Enterprise Edition8, StandardEdition, Standard Edition SP28




8 See5, 6, 7

1. Microsoft Cluster Server (MSCS) in iSCSI supports minimum R26 Flare release version xx.26.xxx.5.007.2. Booting from external storage for iSCSI clusters is not supported.3. Microsoft iSCSI Initiator required. Refer to Native iSCSI table for currently supported initiator version.4. PowerPath 5.0.0 is not supported with Microsoft iSCSI Initiator software and Microsoft Cluster Server (MSCS)5. iSCSI based cluster configurations require Microsoft QFE 824354. Please contact Microsoft Product Support Services for this QFE.6. Booting from external array is supported for iSCSI clusters with QLA4010 iSCSI HBAs. Refer to Native iSCSI table for supported BIOS versions.7. Microsoft Dynamic Disks are not supported.8. Windows Server Core installation option is supported by EMC. Contact your server vendor to determine their support statement for Server Core.9. On Windows 2008 and 2008 R2. In order to support more than a single session between the host and a VNXe array, you must use the "Node and Disk Majority" Quorum

Configuration, you must set the Cluster "Basic resource health check interval to 1, and you must change the iSCSI registry setting for MaxConnectionRetries to 1."10. EMC provides troubleshooting and other technical notes for MSCS cluster solutions. Visit EMC Powerlink and download part number 300-000-603 for the EMC Host Connectivity

Guide for Windows.11. SPC-2 flag must be enabled for iSCSI Symmetrix configurations.12. Configuration utility for QLogic iSCSI HBAs is QLogic SANsurfer available athttp://www.qlogic.com13. QLogic iSCSI HBAs are supported in any server listed in the ESM Fibre Channel tables that list support for the QLA2340 HBAs with the same operating system version listed here.14. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software

Initiator. Refer to the EMC Host Connectivity guide for additional information on Windows iSCSI components and the Microsoft iSCSI Software Initiator usage.15. Clustered hosts may access shared Symmetrix LUNs via iSCSI or Fibre Channel (iSCSI on one node, Fibre Channel on another.)16. QLA4010 iSCSI boards booting from external storage require "Spanning Tree" features to be disabled on network switches used in the boot path.17. Microsoft Initiator software version 2.0 and later automatically forces IQN's to lower-case. This may require array-side host access reconfiguration.18. QLogic iSCSI HBAs require the Microsoft iSCSI Software Initiator Service to be installed. The Service is required by Microsoft and is different from the full Microsoft iSCSI Software


Storage Array


emc support matrix · pdf fileemc support matrix emc's policies and requirements for emc...

Documents