elite pur vinyl sheeting_. introduction_ benefits_ suggested specification_ installation...

ELITE PURVINYL SHEETING_

INTRODUCTION_

BENEFITS_

SUGGESTED SPECIFICATION_

INSTALLATION INSTRUCTIONS_

MAINTENANCE PROCEDURES_

TECHNICAL PROPERTIES_

Elite PUR Vinyl SheetingElite PUR is a high quality polyurethane coated, non-directional, homogeneous vinyl floor covering available in sheeting form with transparent elements included in the pattern.

INTRODUCTION_ Homogeneous vinyl flooring has a uniform structure and composition

from the top to the bottom as there is no separate backing layer

The manufacturing process results in a compact single layer product available in semi-flexible and fully-flexible composition structures

FloorworX offers a wide range of locally produced and imported homogeneous flooring options, which includes Superflex: a fully-flexible, locally manufactured vinyl tile & sheeting range

Elite PUR is a high quality polyurethane coated, non-directional, homogeneous vinyl floor covering available in sheeting form with transparent elements included in the pattern

The balance between the smaller and larger granules creates a natural stone appearance with a soft look

The Elite PUR design expression is light, modern and elegant


BENEFITS_ Durable

Group T abrasion resistance

Non-directional pattern with 3D effect

Wide and fresh range with unique design concept

Outstanding performance

Easy low-cost maintenance


SUGGESTED SPECIFICATION_SHEETING

upply and fix 2.0mm thick x 2.0m wide Elite PUR homogeneous vinyl sheeting with PUR reinforced surface treatment, manufactured in accordance with EN 649 and laid in FloorworX No. 62 acrylic adhesive which has been spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using FloorworX Self Leveller when required, including all cutting and waste

The sheeting must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive

Joins must be butted, grooved and heat welded using FloorworX Welding Rod, ensuring that the welding rod bonds to more than 70% of the sheet thickness.


WARRANTY_

FloorworX offers a 10 year limited warranty, subject to our terms and conditions, against defective material provided that it is installed and maintained in accordance with our recommendations


INSTALLATION INSTRUCTIONS_

Elite PUR should be installed in accordance with manufacturer’s recommendations

Training Centre is available for installation training to installers

SUB-FLOOR_ Sub-floors must be smooth, hard, clean, and dry before laying

commences

The final appearance and durability of any resilient flooring installation depends largely on the condition of the surface upon which it is laid

A good sub-floor is vital in achieving a satisfactory adhesive bond and long-term durability

Uneven, solid or suspended timber floors may need preparation to meet the required standard


SUB-FLOOR_ All sub-floors must be tested for moisture content prior to installation

To prevent problems associated with rising damp - it is essential that a damp-proof membrane be incorporated beneath the sub-floor

The South African Standard Building Regulations require that all sub-floors in contact with the ground are so constructed as to be damp-proof

Water is an integral part of the construction of a sub-floor - the amount of water used depends on the type of sub-floor, the required structural strength and the extent of curing

It is impossible to state a time period after which a sub-floor may be considered dry enough upon which to lay flooring - factors such as ambient temperature, relative humidity, thickness of the slab, type of finish required and methods used to cure the concrete, will affect this period

There are various methods of testing the moisture content within the sub-floor, which includes the use of a Hygrometer – the most practical and accurate instrument


CLIMATIZATION_

Elite PUR must be allowed to relax for 24 hours in a uniform room temperature between 18°C and 27°C prior to installation

ADHESIVE_ The recommended adhesive for Elite PUR is FloorworX No. 62 acrylic

adhesive

Adhesive to be spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre

POST INSTALLATION_ It is essential that during the course of installation the material be

rolled in both directions with an articulated 68kg three section metal floor roller


MAINTENANCE_PREVENTIVE CARE Approximately 80% of the dirt and soiling that has to be cleaned off a

floor has been trafficked in from outside the building. More than 90% of that soiling can be avoided by the use of an effective entrance matting system

When less dirt is trafficked through the entrance there will be a reduction in maintenance requirements.

Regular cleaning is more cost-effective and hygienic than occasional heavy duty cleaning

Wipe up any grease and oil spills immediately and treat stains as soon as they are observed

Black rubber wheels and rubber furniture feet can discolour the floorcovering - hard plastic is preferred

Always follow the manufacturer’s dosage instructions regarding the use of cleaning chemicals


MAINTENANCE_POST INSTALLATION SITE CLEAN Floor maintenance begins immediately after the completion of

installation

The initial step is to remove any loose dirt or debris using a dry mop, broom or vacuum

Sand, construction debris and sharp-edged objects may result in irreparable damage being inflicted to the new floor.

Remove any visible adhesive residue using a damp cloth, once the adhesive has cured it will be difficult to remove

If other trades are working in the building after the installation of the flooring, the floor must be protected from subsequent damage by the use of thick paper, cardboard or hard board.

No wet maintenance must take place until 72 hours (3 days) have elapsed from the time of installation - this is to ensure that the adhesive has sufficient time to cure properly and develop full bond strength


MAINTENANCE_PUR COATED FLOORS PUR coated vinyl floors are protected by means of various cross-linked

polyurethane surface treatments that are applied as part of the manufacturing process

The purpose of these treatments is to protect the floor from the damaging effects of traffic induced scuffing and soiling, but these treatments will only be effective in conjunction with a daily and periodic cleaning and maintenance regime in conjunction with a correctly dimensioned entrance mat. In the event of failure to effectively maintain the thin PUR coating, the user can utilise a sealer-based maintenance program as described for uncoated floors.


MAINTENANCE_INITIAL CLEAN Dust mop or vacuum the floor to remove loose soil and dust

Scrub the floor using a solution of FloorworX Maintain diluted 1:10 with clean water, with a rotary machine fitted with a blue pad

Remove the residue immediately after scrubbing using a wet/dry vacuum

Rinse with clean water using a flat mop and allow the floor to dry

Dry buff the floor using a rotary or high speed machine fitted with a white pad

For higher traffic areas, apply FloorworX Spray Buff in a fine stream or mist onto the floor in front of a rotary machine fitted with a red pad and work in until dry

FloorworX Spray Buff applied in this manner at the rate of 600m2 per litre assists in maintaining a smooth surface and constant level of gloss


MAINTENANCE_REGULAR CLEANING Dust mop with flat mop or vacuum on a daily basis to remove dust and

loose dirt

Treat spills, spots and stains immediately

Spot clean by hand with a red or white pad and a diluted solution of FloorworX Maintain, working from the outside of the mark to its centre

Dry buff or spray buff periodically, as described in 4.1 Initial Clean above

The frequency of dry buffing or spray buffing is dependent on the amount of foot traffic and the effectiveness of the daily cleaning regime


MAINTENANCE_PERIODIC MAINTENANCE Scrub the floor using a solution of FloorworX Maintain diluted 1:10 with

clean water, with a rotary machine fitted with a blue pad

Remove the residue immediately after scrubbing using a wet/dry vacuum

Rinse with clean water using a flat mop and allow the floor to dry

Dry buff the floor using a rotary or high speed machine fitted with a white pad

For higher traffic areas, apply FloorworX Spray Buff in a fine stream or mist onto the floor in front of a rotary machine fitted with a red pad and work in until dry

FloorworX Spray Buff applied in this manner at the rate of 600m2 per litre assists in maintaining a smooth surface and constant level of gloss


MAINTENANCE_PERMANENT DAMAGE If the cleaning and maintenance regime as described above is unable

to prevent permanent damage being done to the PUR coating as a result of traffic-induced scuffing and soiling, then it may be necessary to adopt the same strip, seal and spray buff approach as has been described for UNCOATED VINYL FLOORING


MAINTENANCE_STRIP AND SEAL (PERMANENT DAMAGE ONLY) Using a lambswool applicator, apply a thin, even coating of FloorworX

Silk Matt or Gloss Sealer at a rate of 20m2 per litre

Allow sufficient time for the coating to dry thoroughly

Apply the 2nd coat of FloorworX Silk Matt or Gloss Sealer at right angles to the initial coat and allow sufficient time to dry thoroughly

Ensure that the floor is not trafficked between coats

Apply the 3rd and final coat of FloorworX Silk Matt or Gloss Sealer at right angles to the previous coat and allow sufficient time to dry thoroughly

Once the initial strip and seal process is complete, ensure that the mops, pads and lambswool applicators are rinsed thoroughly in warm water and allowed to dry for re-use


TECHNICAL PROPERTIES_


Please feel free to visit our newly revamped website at www.floorworx.co.za

Read our Blog on our website at http://www.floorworx.co.za/category/blog/

Subscribe to our Newsletter by mailing your request to [email protected]

Follow us on Facebook, Twitter, YouTube & Pinterest

END OF PRESENTATION_

http://www.floorworx.co.za/

http://www.floorworx.co.za/category/blog/

http://www.floorworx.co.za/category/blog/

mailto:[email protected]

elite pur vinyl sheeting_. introduction_ benefits_ suggested specification_ installation...

Documents