electronics (1).docx

Upload: jennifer-goodwin

Post on 02-Jun-2018

216 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/10/2019 ELECTRONICS (1).docx

    1/7

    UTILITY BOX-A location or enclosure which is suitable for housing or storing electrical or communications components,

    circuits, devices, equipment, materials, cables, connections, and the like. Such a box, for instance, may be portable, or

    might be recessed into a wall or floor.

    ELECTRICAL CONNECTORS-An electrical connector is an electro-mechanical device for joining electrical circuits as an

    interface using a mechanical assembly.

    MALE PLUG-A male connector is a connector attached to a wire, cable, or piece of hardware, having one or more

    exposed, unshielded electrical terminal s, and constructed in such a way that it can be inserted snugly into a receptacle (

    female connector ) to ensure a reliable physical and electrical connection . This type of connector is also known as a plug.

    A male connector can be recognized by the fact that, when it is disconnected or removed, the unshielded electrical prongs

    are plainly visible.

    FUSE-a fuse (from the French fuser, Italian fuso, "spindle"[1]) is a type of low resistance resistor that acts as a sacrificial

    device to provide overcurrent protection, of either the load or source circuit. Its essential component is a metal wire or strip

    that melts when too much current flows through it, interrupting the circuit that it connects. Short circuits, overloading,

    mismatched loads, or device failure are the prime reasons for excessive current. Fuses are an alternative to circuit

    breakers.

  • 8/10/2019 ELECTRONICS (1).docx

    2/7

    CONDUIT-An electrical conduit is a tubing system used for protection and routing of electrical wiring. Electrical conduit

    may be made of metal, plastic, fiber, or fired clay. Flexible conduit is available for special purposes.

    CIRCUIT BREAKER-A circuit breaker is an automatically operated electrical switch designed to protect an electrical circuit

    from damage caused by overload or short circuit. Its basic function is to detect a fault condition and interrupt current flow.

    ELECTRICAL WIRES-A wire is a single, usually cylindrical, flexible strand or rod of metal. Wires are used to bear

    mechanical loads or electricity and telecommunications signals.

    CPC-refers to a wide range of extruded twinwall plastic-sheet products produced from high-impact polypropylene resin

    with a similar make-up to corrugated fiberboard. It is a light-weight tough material which can easily be cut with a utility

    knife. Manufacturers typically offer a wide variety of colors and thicknesses (quite commonly 3, 4, 5 mm).

  • 8/10/2019 ELECTRONICS (1).docx

    3/7

    RECEPTACLE-are devices that allow electrically operated equipment to be connected to the primary alternating current

    (AC) power supply in a building. Electrical plugs and sockets differ in voltage and current rating, shape, size and type of

    connectors.

    FUSE PANEL- is a component of an electricity supply system which divides an electrical power feed into subsidiary

    circuits, while providing a protective fuse or circuit breaker for each circuit, in a common enclosure.

    SQUARE BOX-Covers are used to close an outlet box and are required by code. Never leave a box uncovered

    PVC Conduit-PVC is the lightest conduit material and usually the lower cost conduit material. PVC conduits can vary in

    thickness depending on the uses and where the PVC will be installed. The PVC conduit resist moisture and corrosion but

    the tubing is non-conductive an extra grounding conductor must be passed into each conduit.

  • 8/10/2019 ELECTRONICS (1).docx

    4/7

    SWITCH- a switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it

    from one conductor to another.

    CUT-OUT BOXES-A metal box used in electrical wiring to house circuit breakers, fuses, or a disconnect switch.

    SWITCH PLATE. : the metal plate in front of an electrical switch box through which the plugs or tumblers protrude.

    TOOL-A tool is any physical item that can be used to achieve a goal, especially if the item is not consumed in the process.

    Informally the word is also used to describe a procedure or process with a specific purpose.

    LONG NOSE PLIER-Needle-nose pliers (also known as pointy-nose pliers, long-nose pliers, pinch-nose pliers or snipe-

    nose pliers) are both cutting and holding pliers used by artisans, jewelry designers, electricians, network engineers and

    other tradesmen to bend, re-position and cut wire.

  • 8/10/2019 ELECTRONICS (1).docx

    5/7

    STUBBY SCRWDRIVER-A stubby screwdriver is a tool used to facilitate access to screws located in areas that cannot be

    reached easily by a regular screwdriver.

    WIRE STRIPPERA wire stripperis a small, hand-held device used to strip theelectrical insulationfrom electricwires.

    ELECTRIC DRILL is a tool fitted with a cutting tool attachment or driving tool attachment, usually a drill bit or driver bit,

    used for boring holes in various materials or fastening various materials together with the use of fasteners.

    PHILLIPS SCREWDRIVER is a tool, manual or powered, for turning (driving or removing) screws. A typical simple

    screwdriver has a handle and a shaft, and a tip that the user inserts into the screw head to turn it.

    http://en.wikipedia.org/wiki/Electrical_insulationhttp://en.wikipedia.org/wiki/Electrical_insulationhttp://en.wikipedia.org/wiki/Electrical_insulationhttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Electrical_insulation
  • 8/10/2019 ELECTRONICS (1).docx

    6/7

    COMBINATION PLIERS are a type ofpliers used byelectricians and othertradesmen primarily for gripping, twisting,

    bending and cuttingwire andcable.

    Hammeris atool that delivers an impact to an object.

    ELECTRICIANS KNIFE-A short-bladed knife used to cut electrical insulation.

    Hacksawis a fine-toothedsaw,originally and principally for cuttingmetal.

    http://en.wikipedia.org/wiki/Pliershttp://en.wikipedia.org/wiki/Electricianhttp://en.wikipedia.org/wiki/Tradesmenhttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Cablehttp://en.wikipedia.org/wiki/Toolhttp://en.wikipedia.org/wiki/Sawhttp://en.wikipedia.org/wiki/Metalhttp://en.wikipedia.org/wiki/Metalhttp://en.wikipedia.org/wiki/Sawhttp://en.wikipedia.org/wiki/Toolhttp://en.wikipedia.org/wiki/Cablehttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Tradesmenhttp://en.wikipedia.org/wiki/Electricianhttp://en.wikipedia.org/wiki/Pliers
  • 8/10/2019 ELECTRONICS (1).docx

    7/7

    DIAGONAL CUTTING PLIERS arepliers intended for thecutting ofwire

    Half round files taper in width and thickness, coming to a point, and are narrower than a standard half round. Used

    for filing inside of rings.

    ROUND FILE-a file with a circular cross section; used to file the inside ofholes.

    A spirit level, bubble levelor simply a levelis aninstrument designed to indicate whether a surface

    ishorizontal (level) orvertical (plumb).

    http://en.wikipedia.org/wiki/Pliershttp://en.wikipedia.org/wiki/Cuttinghttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Measuring_instrumenthttp://en.wikipedia.org/wiki/Horizontal_planehttp://en.wikipedia.org/wiki/Vertical_directionhttp://en.wikipedia.org/wiki/Plumb-bobhttp://en.wikipedia.org/wiki/Plumb-bobhttp://en.wikipedia.org/wiki/Vertical_directionhttp://en.wikipedia.org/wiki/Horizontal_planehttp://en.wikipedia.org/wiki/Measuring_instrumenthttp://en.wikipedia.org/wiki/Wirehttp://en.wikipedia.org/wiki/Cuttinghttp://en.wikipedia.org/wiki/Pliers