electronic - westlat design, llc.westlat.com/supportfiles/pentax/manuals/r300x quick basic...
TRANSCRIPT
ElectronicTotal Station
R-322NX R-322EXR-323NX R-323EXR-325NX R-325EXR-335NX R-335EXR-315NX R-315EX
R-326EX
Quick Reference Guide
Total Surveying Solutions
The reflectorless function is applied to
R-322NX, R-323NX, R-325NX, R-326EX, R-335NX, R-315NX
Basic Procedures for R-300X Series PENTAX Industrial Instruments Co., Ltd.
2-5-2 Higashi-Oizumi / Nerima-ku, Tokyo 178-0063, JapanTel. +81 3 5905 1222 / Fax +81 3 5905 1225
E-mail: [email protected]: www.pentax.co.jp/piic/survey
www.pentaxR300X.com
Electronic Total Station
Quick Reference GuideBasic Procedures for R-300X series
R-322NX, R-323NX, R-325NX, R-335NX, R-315NX,R-322EX, R-323EX, R-325EX, R-335EX, R-315EX, R-326EX
The description concerning the reflectorless function in this guide is applied to
R-322NX, R-323NX, R-325NX, R-326EX, R-335NX, R-315NX.
Total Surveying Solutions
5
CONTENTS
General 6Instruction Manuals 6Precautions regarding safety 6Warning 6 Usage Precautions 7
1 Basic Operation 91.1 Removing the Battery 9 1.2 Attaching the Battery 91.3 Turning the Power On and Off 91.4 Centering and Leveling 91.5 Target Sighting (Focusing) 10
1.5.1 Auto-Focus 101.5.2 Power Focus 10 1.5.3 Manual Focus 10 1.5.4 Continuous AF mode 10
1.6 Angle Measurement 111.6.1 Horizontal Angle 111.6.2 Vertical Angle 11
1.7. Distance Measurement 121.7.1 Select your target 121.7.2 Distance Measurement 121.7.3 Changing Target constants 121.7.4 Input Temperature and Atmospheric pressure 131.7.5 Laser pointer 131.7.6Adjusting Laser Plummet brightness 131.7.7 Adjusting LCD contrast 131.7.8 Adjusting Illumination brightness 14
2 Changing Instrument Settings 15
3 Basic Field Checking Procedures 163.1 Electronic Vial 163.2 Laser Plummet 163.3 Laser Pointer 163.4 Warning and Error Messages 173.5 Atmospheric Correction 18
4 Specifications 19Notice to the user of this product 20
ESC
6
Instruction ManualsQuick Reference Guide is intended to provide a quick reference in thefield. For ease of use in the field, the following Quick Reference Guidebooklets are provided in the carrying case.
1. Basic procedure2. PowerTopoLite for R-300X series, Operating procedure
The complete instruction manuals are contained on the CD that isattached to each R-300X.
This guide uses the symbol “ xN” as an expression of repeating timesof key operation. For example. “ x2” means that [ESC] key ispressed two times.The symbol “+”expresses that multiple keys are pressed simultaneously.
PRECAUTIONS REGARDING SAFETYBefore using this product, be sure that you have thoroughly readand understood the instruction manual that is included in theattached CD-ROM to ensure proper operation.
WARNING
Solar ObservationNever view the sun directly using the telescope as this may result in loss of sight.
Laser SafetyR-300NX is a class-IIIa (3R) Laser product. Avoid direct eye exposure.R-300X without “NX” is a class-II (2) Laser product. Do not stare into laser beam.
Electro-Magnetic Compatibility (EMC)This instrument complies with the protection requirement for residential and commercial areas. If this instrument is used close to industrial areas or transmitters, the equipment can be influenced by electromagnetic fields.
7
Risk of ExplosionDo not use this product in a location where there is coal dust, or near flammable material as there is a risk of explosion.
USAGE PRECAUTIONS
Target ConstantConfirm the Target Constant of the instrument before measurement.
Reflectorless and Reflecting sheetThe reflectorless measurement range may vary depending on the target and surrounding brightness.In case the reflectorless measurement results in low accuracy,perform the distance measurement by Reflector sheet or Prism.(R-322NX, R-323NX, R-325NX, R-335NX, R-315NX,)
Battery & ChargerUse the battery charger that is suitable to the battery you are using.If water should happen to splash on the instrument or the battery,wipe it off immediately and allow it to dry in a dry location.
Auto focusThe Auto focus may not function under every condition depending on brightness,contrast,and the shape and size of the target. In such a case, use the Power Focus buttons or the manual focus ring.
Atmospheric correctionDuring surveys for which the survey precision or atmospheric measurement method is defined, measure the atmospheric temperature and pressure separately and enter those values rather than using the Automatic Atmospheric Correction function.
9
1. Basic Operation
1.1 Removing the Battery
(1) Rotate the knob above the battery pack counter-clockwise.(2) Lift up the battery pack and remove it from the instrument.
1.2 Attaching the Battery
(1) Place the channel on the bottom of the battery pack, onto the protrusion of the instrument and push the battery pack down into place.
(2) Turn the knob clockwise.
1.3 Turning the Power On and Off
To set power on : Electronic vial screen
To shut down :
NOTE: The power is automatically turned off after 10 minutes of inactivity (Factory default setting).
1.4 Centering and Leveling (Laser plummet and Electronic vial)
To activate electronic vial : or:
To activate laser plummet : (for the first time after power on)
NOTE: The laser plummet and the electronic vial are always activated at the same time.When the power is switched on,however, only electronic vial is activated (Factory default setting).To change the power-on activation of laser plummet, refer to “2.3 Instrument setting items”.F
PLUM.ADJ
F3
ENT
ESC
or:
To deactivate : or:
10
1.5 Target Sighting (Focusing)
1.5.1 Auto-Focus Aim using the telescope collimator, and press
NOTE: Place the target near the reticle center.The AF sensor is located around the horizontal line of the reticle.
1.5.2 Power focusIf the AF failed or if you need to adjust the focus, use the Power focus knob.
To focus on a closer object : Rotate Power Focus knob clockwiseTo focus on a farther object : Rotate Power Focus knob counter-clockwise
NOTE: Focus speed can be controlled by the rotation angle of the knob:
Low speed: when rotated by approx. 5 degreesMiddle speed: when rotated fully by approx. 10 degreesHigh speed: after one second of time has passed in the
middle speed position
1.5.3 Manual focus
Rotate the focus ring manually:
1.5.4 Continuous AF modeTo activate the continuous AF: … for 2 seconds
NOTE: Track the target by keeping the target close to the center of the reticle as much as possible.
To quit: or rotate the Power focus knob :
NOTE: In case the focus does not change for one minute, thecontinuous AF mode will also terminate automatically.
11
1.6 Angle Measurement
1.6.1 Horizontal AngleSet the screen MODE A : or MODE A screen
Control keys for measuring horizontal angle:
To set the angle to 0 :
To hold the angle :
To release HOLD :
To input an angle :
To read clockwise angle :
1.6.2 Vertical angleTo display vertical angle :
To change permanently the combination of values displayed inMODE A:
To read the slope % :
1.7 Distance Measurement
Set the screen MODE A: or MODE A screen
ESC
0 SET
F3
0 SET
F3
MODE
F5
HOLD
F3
HOLD
F3
HOLD
F3
MODE
F5
ANG SET
F2 F4
SELECT
F5
F1 F20 9 .
ENT, , ,input value by using:
MODE
F5
ANG SET
F2 F4
SELECT
F5x2
DISP
F4
ESC
F2
SELECT
F5 F4
SELECT
F5x2 x3
F3 F4
ENTSelect by x3
MODE
F5
ANG SET
F2
SELECT
F5
or
+
[ ]
[ ]ESC
12
1.7.1 Select your targetSelect target type (measurement mode):
(Reflecting sheet) (Prism) (Reflectorless)
NOTE: The selected target is maintained until next time you change.
1.7.2 Distance measurementFor a single shot measurement:
NOTE: “Long Range Mode”is displayed only when measuring with higher laser power (in reflectorless measurement with the instrument setting “REF.LESS RANGE”set as “LONG”and“Warning Message”set as “ON”.)
For tracking measurement :
NOTE: The number of shots can be defined.The default is “one time”. The measuring modes activated by the above operationscan be also changed.
NOTE: Quick mode is the function to shorten the initial measurement time using prism and reflector sheet.To set the mode,use direct command number [0][0][7][5][2][2].When the meas key ispressed during quick mode, ”<-- -->” is displayed on the screen.
1.7.3 Changing Target constantsThe default constants are:Reflecting sheet : 0mmPrism : -30mmReflector-less : always 0mmBefore changing the constants, set Target Constant in the InitialSetting to “INPUT” mode:
To change Prism constant:
TARGET
F2
TARGET
F2
TARGET
F2
MEAS
F1
MEAS
F1
When “Long Range Mode” is displayed
MEAS
F1
ESC
F4
SELECT
F5 F4
ENTx2 x2 x3
MODE
F5
CORR
F4SELECT
F5
ENT[ ]
+
input valueby using : F1
0 9 .ENT
, , , x2F2
13
To change Sheet constant:
1.7.4 Input Temperature and Atmospheric pressureThe default atmospheric correction mode is “Automatic”.Before manual input, change the default mode to “ATM INPUT” :
To Input temperature :
To Input atmospheric pressure:
1.7.5 Laser pointerTo activate Laser pointer :
To quit Laser pointer :
NOTE: The laser pointer is kept activated until it is deactivated by the above procedure.
1.7.6 Adjusting Laser Plummet brightness
or
1.7.7 Adjusting LCD contrast
or
MODE
F5
CORR
F4 F4
SELECT
F5
input value by using:F1 F2
0 9 .ENT
, , , x2
ESC
F4
SELECT
F5 F4
ENTx2 x2
MODE
F5
CORR
F4 F4
SELECT
F5x2
input value by using:F1 F2
0 9 .ENT
, , , x2
MODE
F5
CORR
F4 F4
SELECT
F5x3
input value by using:F1 F2
0 9 .ENT
, , , x2
LD POINT
F2
LD POINT
F2
PLUM.ADJ
F3 F1 F2
ENT
LCD
F4 F1 F2
ENT+
+
14
1.7.8 Adjusting Illumination brightness
for LCD (for Reticle) or
2. Changing Instrument settings
You can change the instrument settings by “HELP” menu or byinputting “007” code.
2.1 Help menuWhile the screen is in MODE A or MODE B,
Select a desired item by or
NOTE: Some items have sub-menus where the selecting procedure by using F1 - F4 is again repeated.
2.2 “007” codeWhile the screen is in MODE A or MODE B,
Input 007 code by using
NOTE: Some items have sub-menus where the selecting procedure by using F1 - F4 is again repeated.
2.3 Instrument setting items
See chart on page 15
ILLU
F5
RECTICLE
F3 F2
ENT
F1+
ESC+
F4F3
SELECT
F5 Change the settingENT
x2
0 9ENT
0 0 7
SELECT
F5 Change the settingENT
x2
15
007
cod
e H
ELP
men
u li
st
Def
ault
Oth
er o
pti
on
s 40
1TA
RGET
CO
NST
PR
ISM
CO
NST
-3
0mm
0m
m,
INPU
T
SHEE
T C
ON
ST
0mm
IN
PUT
40
2 AT
M C
ORR
A
UTO
AT
M IN
PUT,
pp
m IN
PUT,
NIL
50
1 M
EAS.
MIN
DIS
P C
OA
RSE
FIN
E 50
2 SH
OT
CO
UN
T SH
OT
CO
NT
1
tim
e 3
tim
es,5
tim
es,I
NPU
T
SHO
T IN
PUT
01
tim
es
(inp
ut)
50
3 C
RV
/REF
CO
RR
0.14
0.
2,N
IL
504
MIN
UN
IT A
NG
.FI
NE
CO
ARS
E
505
V.A
NG
.STY
LE
Z.0
H
.0,C
OM
PASS
50
8 D
IST.
BUZ
O
N
OFF
50
9 Q
UA
D B
UZ
O
FF
ON
51
0 A
UTO
OFF
10
MIN
20
MIN
,30
MIN
,NIL
51
1 ED
M O
FF
3 M
IN
5 M
IN,1
0 M
IN,N
IL
512
ILLU
.OFF
3
MIN
5
MIN
,10
MIN
,NIL
51
4 M
EAS.
SIG
NA
L M
ARK
VA
LUE
51
5 PR
IORI
TY S
ELEC
T PR
IM.M
EAS
KEY
MEA
S SH
OT
MEA
S C
ON
T,TR
AC
K SH
OT,
TRA
CK
CO
NT
SE
C.M
EAS
KEY
TRA
CK
CO
NT
TRA
CK
SHO
T,M
EAS
CO
NT,
MEA
S SH
OT
A
UTO
MEA
S.N
IL
MEA
S.,T
RAC
K
PRIO
RITY
DIS
P H
A/H
D/V
D
HA
/VA
/SD
,HA
/VA
/HD
/SD
/VD
51
7 C
OM
P A
XIS
3
Axi
s (2
/3”m
odel
) or 2
Axi
s2
Axi
s (2
/3”m
od
el),
1Axi
s,,N
IL52
0 LD
PLU
M.&
E.V
IAL
LD P
LUM
.O
FF (w
hen
Pow
er O
n)
ON
(au
tom
atic
ally
ON
)
TILT
DIS
P.O
FFO
N
TILT
DIS
P.U
NIT
CO
ARS
EFI
NE
521
REF.
LESS
RA
NG
E RA
NG
E N
ORM
AL
LON
G
M
ESSA
GE
ON
(wh
en R
ang
e is
LO
NG
)O
FF
SE
TUP
EAC
H T
IME
(w/
Pow
er O
N)
PERM
AN
ENT
52
2Q
UIC
K M
EAS
OFF
ON
701
ATM
UN
IT
TEM
P.U
NIT
C
enti
gra
de
Fah
ren
hei
t
PRES
S U
NIT
h
Pa
mm
Hg,
inch
Hg
70
2 D
IST.
UN
IT
m
ft,f
t+in
ch
703
AN
G.U
NIT
D
EG
DEC
,GRD
,MIL
80
1 SE
T U
P C
OM
.BA
UD
RAT
E 12
00
2400
,480
0,96
00
D
ATA
LEN
GTH
8 7
PA
RITY
BIT
S N
IL
EVEN
,OD
D
ST
OP
BITS
1
2
SIG
NA
L C
ON
TRO
L O
N
OFF
XON
/XO
FF
ON
O
FF
TH
ROU
GH
CO
MM
AN
D
NIL
a,
b,c,
d,e,
f
16
3. Basic Field Checking Procedures
Checks and Adjustments should be performed before and during measurement.
3.1 Electronic VialTo display vials: or (from measurement screen)
Check if the bubble stays at the center of each vial, when rotating the instrument by 180°.
To adjust the vials: operate according to the instruction on the screen
NOTE: Press these two keys for 1 second longer, then release key first.
3.2 Laser PlummetTo activate the laser plummet:
(for the first time after Power on) or (from measurement screen)
Check if the laser spot on the ground stays at the same position whenrotating the instrument around the vertical axis.To adjust the laser plummet: Contact your local dealer
3.3 Laser PointerTo activate the laser pointer:
or (from measurement screen)
Check if the projected laser spot points at the same position that isaimed by the center of the cross-hair line of the telescope.To adjust the laser pointer: Consult your local dealer.
+
PLUM.ADJ
F3
ENT
LD POINT
F2
LD POINT
F2
17
3.4 Warning and Error Messages
Warning Message Meaning What to doDisplayed when the instrument is til-ted beyond the vertical compensationrange (±3’) in case 1 axis or 2 axis automatic compensation is selected.This message may be temporarily dis-played if the instrument is turned toofast.
The input data exceeds the allowablerange.
• This message is displayed if a long distance which is a far beyond measurable distance of R-300X series is measured with a wrong target mode.Please select a correct target then measure.If a wrong target is selected, a correct distance cannot be measured.
• The measurement distance is less than 1.5m in Reflector sheet mode.
• The measurement distance is less than 1.5m in Prism mode.
• Under too strong sun light.• Unstable light value owing to
shimmer or obstacles.• Reflector sheet, Target and Prism do
not face the instrument.• Reflector sheet,Target and Prism are
not correctly sighted.• Measurement range is over in
Reflectorless mode.• Sufficient signal does not return by
sighting sharp edge etc. at Reflectorless mode.
• The Date Clock is powered by the built-in lithium battery.
• The lithium battery needs to be replaced in five years.
Re-level the instrument.Repair is needed if themessage is displayedwhen it is properly leveled.
Press the [ESC] key andenter the correct data.
Select the correct targetmode.
Select a longer point,or use a tape measure.
Change the object that has much betterreflectivity, or use a reflecting sheet, or waituntil the sun activityhas weakened.
Have the lithium batteryreplaced by the dealerfrom whom the instrument was purchased.
Out of tilt range
Excess data
MismatchedTarget
Target is tooclose.
UnsuitableCondition
Li-batt.voltage islow.
18
ERROR!! EDM ERROR 04 -05, 34-39, 50-53
ERROR!!ETH ERROR 70-76
ERROR!!MEMORY ERROR 19
ERROR PS DATA of EDM ERROR P DATA of EDM
ERROR ETH DATA
Distance measurement system problem
Angle measurement system problem
Memory problem
Problem of the internal EDM parameters
Problem of the internal ETH parameters
Turn the power off, and then turn onagain. Repair isneeded when themessage appears consistently.
Error Message Meaning What to do
3.5 Atmospheric Correction
The speed at which light travels through the air varies dependingon the temperature and atmospheric pressure. The R-300X series is designed to measure distances at the speed of light in order to measure accurately, atmospheric correction needs to be used.The instrument is designed to correct for weather conditions automatically if the temperature and pressure are input.Correction is then carried out based on the following formula.
Calculation formula:
K= (276.26713 - 78.565271 • P ) x10-6
K: Atmospheric Correction ConstantP: Atmospheric pressure (hPa)t: Temperature(°C)Distance after Atmospheric Correction D = Ds (1+K)Ds: Measured distance when no Atmospheric Correction is used.
273.14941 + t
4. Specifications
R-322NX R-323NX R-325NX R-335NX R-315NXR-322EX R-323EX R-325EX R-335EX R-315EX R-326EX
TelescopeMagnification 30 x Resolving power 3”Field of view 2.6% (1° 30’) Minimum focus 1.0m Focus Auto-focus / Power Focus / Manual Manual Distance measurementLaser Class Visible Laser: Class II (2) / Class IIIa (3R) Visible Laser: Class II (2)
- Long range mode in Reflectorless (“NX” models only)Measurement range (Good condition) Reflectorless 1.5m - Normal range mode: 90m / Long range mode 200m (“NX”models only) -Reflector sheet 1.5m-600m (800m) Mini prism 1.5m-1100m (1600m) 1P 1.5m-3400m (4500m) 1.5m-3000m (4000m) 1.5m-2000m (2800m) 3P 200m-4500m (5600m) 200m-4000m (5000m) 200m-2800m (3500m) AccuracyPrism ±(2+2ppm x D)mm ±(3+2ppm x D)mmReflector Sheet Reflectorless ±(5+2ppm x D)mm ±(5+3ppm x D)mm At Auto-Atm.Correction Prism, Ref.sheet: ±(2 +10ppm x D)mm / ±(3+10ppm x D)mm
Reflectorless: ±(5 + 10ppm x D)mm (“NX”models only)
Minimum count Fine mode (0.1mm) Normal mode (1mm) Track mode (1cm) Measuring timeRepeat meas. Normal:Prism,Ref.sheet 2.0sec. (1mm) Normal: Prism, Ref.sheet 1.2sec. (1mm)
Track: Prism,Ref.sheet 0.4sec. (1cm) *Quick mode Initial meas. Normal:Reflectorless 2.3sec. (1mm) Normal: Prism, Ref.sheet 2.5sec. (1mm)
(“NX”models only) *Quick modeAngle measurementMeasuring method Absolute rotary encoder Detection 2 sides Minimum count 1” (2cc) / 5” (10cc) selectable Accuracy(ISO 17123-3) 2” 3” 5” 6”Compensator Triple axis Dual axis Tangent screw 2 speed 1 speed Sensitivity of vialsPlate level (electronic) 30”/1div.Circular level 8’/2mm Plummet Visible Laser, ±0.8mm (instrument height 1.5m) Base Detachable Shifting Fixed Detachable Water resistant IP56Ambient temperature -20°C ~ +50°C / -4°F ~122°F (Working range) Tripod thread 5/8” x 11 35mm x 2 5/8” x 11 Dimensions/WeightInstrument 177(W) x 343(H) x 177(L)mm Weight (incl. Battery) 5.7kg 5.5kg 5.7kg Carrying case 268(W) x 442(H) x 465(L)mm/3.9kg Battery pack BP02Power source Ni-MH (Rechargeable)(4300mAh) , DC6V Operation time Continuous Approx. 5 hrs (ETH+EDM),12 hrs (ETH) with Approx. 2.2 hrs of charging timeWeight Approx. 380g
Reflectorless items are applicable to “NX” models only.
19
20
R-322NX R-323NX R-325NX R-335NX R-315NXR-322EX R-323EX R-325EX R-335EX R-315EX R-326 EX
Charger BC03 and AC Adapter AC01Input voltage (AC01) AC 100~240V (AC01)Output voltage (BC03) DC7.5V (BC03)Weight 280g Internal MemoryCoordinates data 20000 points 16000 points 12000 points Date Clock
NX MODEL Yes Yes -EX MODEL Yes No No
NOTE: * The measurement range may vary by measurement conditions.
* Normal conditions: 20km visibility with slight shimmer.* Good conditions: 40km visibility, overcast, no heat, no
shimmer and moderate wind.* Reflector sheet: PENTAX genuine Reflector sheet (5cm x 5cm).* Quick mode, which is effective only under Normal mode
(1mm) setting, functions with Prism and Reflector Sheet. It is incorporated in all X series models and effective up to 500m.
* When Quick Mode is on, the EDM accuracy using Prism andReflector Sheet is ±(3+2ppm x D)mm. When AutomaticCorrection is activated in Quick Mode, the EDM accuracy is±(3+10ppm x D)mm
* EDM Measuring time varies according to distance to be measured and conditions of the environment.
* Reflectorless:- The measurement range and accuracy of Reflectorless
are based on the condition that laser beam is emitted perpendicular to the white side of the Kodak Gray Card.There is a possibility that the range may vary when the target does not satisfy the conditions above at survey work.
- The measurement range may be influenced by the shape of the target and its environment.
- The measurement range at TRACK mode is over 5m.* The operating time becomes shorter under the low
temperature, due to the temperature dependence of the battery performance.
* The points that can be recorded in one job file are maximum 2,000 measuring points (XYZ).The user can make up to 50 job files. Job history can bemanaged thanks to date clock recorded in each job file.
21
NOTICE TO THE USER OF THIS PRODUCT
To assure compliance with the Safety standard 21 CFR, Chapter 1.Subchapter J. The U.S. bureau of Radiological Health requires the following information to be provided to user.:
It can be dangerous to look into the beam with optical equip-ment such as binoculars and telescopes.
1. Specifications of Laser Radiation
A) The EDM module of the R-300X produces a visible light beam,which is emitted from the telescope objective lens and thecenter hole of the instrument base plate.The R-300X is designed and built to have a laser diode radiating at 620-690nm.
B) Radiant powerThe R-300X is designed and built to radiate a maximum average radiant power of 4.75mW (0.95mW for the model without “NX”) from the telescope,and 0.95mW from the center hole of the base plate.The user may be subject to this radiation as a beam while operation until such time that the instrument is turned off.
2. The following labels are affixed to and must remain attached to this laser product.
A) The following Certification label is located near the Plate level:“This laser product is complied with the provisions of 21 CFR 1040. 10 and 1040.11. For a Class II laser product.”
Or for R-300 NX models:“This laser product is complied with the provisions of 21 CFR 1040. 10 and 1040.11. For a Class IIIa laser product.”
B) Caution label is located near the exit aperture:“AVOID EXPOSURE.Laser radiation is emitted from this aperture.”
2222
C) Warning logotype is located on the surface of the telescope:“CAUTION LASER RADIATION DO NOT STARE INTO BEAM”
Or for R-300 NX models:“DANGER LASER RADIATION AVOID DIRECT EYE EXPOSURE”
D) Warning label is Located near the exit aperture.
3. Caution to maintain the safety in compliance with the standard
A) To maintain the safety standard, refrain from any operation,maintenance, or adjustment other than described in this instruction manual.
B) Operation, maintenance or adjustment other than those specified in this instruction manual may result in hazardous radiation exposure.
C) Maintenance and repair not covered in this manual must be done by an authorized Pentax dealer.
D) The Laser beam emission by the Distance measurement can be terminated by pressing key.
E) Pressing keys can terminate the laser beam emission by the laser pointer.
F) The Laser beam emission by the Laser plummet can be terminated by pressing key.
MEAS
F1
LD POINT
F2
23
AV
OID
EX
POSU
RELa
ser r
adia
tio
nis
em
itte
d fr
om
this
ap
ertu
re
Ap
ertu
re la
bel
AV
OID
EX
POSU
RELa
ser r
adia
tio
nis
em
itte
d fr
om
this
ap
ertu
re
Ap
ertu
re la
bel
War
nin
g la
bel
Lase
r bea
m is
tra
nsm
itte
d
fro
m t
his
ap
ertu
re
Iden
tific
atio
n la
bel
R3
25
EX
R3
35
EX
R3
15
EX
R3
22
EX
R3
23
EX
R3
26
EX
R3
25
NX
R3
35
NX
R3
15
NX
R3
22
NX
R3
23
NX
Lase
r bea
m is
tra
nsm
itte
d fr
om
th
is a
per
ture
24
War
nin
g lo
go
typ
eW
arn
ing
log
oty
pe
Lase
r bea
m is
tra
nsm
itte
d
fro
m t
his
ap
ertu
re
For N
ort
h A
mer
ica
Cer
tific
atio
n
LASE
R RA
DIA
TIO
NA
VO
ID D
IREC
T EY
EEX
POSU
REC
LASS
3R
LASE
R PR
OD
UC
T
LASE
R RA
DIA
TIO
N
AVO
ID D
IREC
T EY
E
EXPO
SURE
CLA
SS 3
R LA
SER
PRO
DU
CT
LASE
R RA
DIA
TIO
ND
O N
OT
STA
RE IN
TO B
EAM
CLA
SS 2
LA
SER
PRO
DU
CT
For R
-300
NX
mo
del
For R
-300
EX m
od
el
For R
-300
NX
mo
del
For R
-300
EX m
od
el
For R
-300
NX
mo
del
For R
-300
EX m
od
el
2-5-
2 H
igas
hi O
zum
i Ner
ima-
ku. T
oky
o 1
78-8
555
Jap
anTh
is L
aser
pro
du
ct is
co
mp
lied
wit
h t
he
pro
visi
on
s o
f 21
CFR
104
0-10
an
d 1
040-
11 F
or a
cla
ss II
Ia p
rod
uct
ASS
EMB
LED
BY
PEN
TAX
VN
Co.
LTD
Sai
Do
ng
B In
du
stri
al z
on
e. G
ia L
am. H
ano
i Vie
tnam
2-5-
2 H
igas
hi O
zum
i Ner
ima-
ku. T
oky
o 1
78-8
555
Jap
anTh
is L
aser
pro
du
ct is
co
mp
lied
wit
h t
he
pro
visi
on
s o
f 21
CFR
104
0-10
an
d 1
040-
11 F
or a
cla
ss II
pro
du
ctA
SSEM
BLE
D B
Y P
ENTA
X V
N C
o. L
TDSa
i D
on
g B
Ind
ust
rial
zo
ne.
Gia
Lam
. Han
oi V
ietn
am
CA
UTI
ON
DANGER
LED
is t
urn
ed o
n a
t th
e ti
me
of e
mis
sio
n
DA
NG
ER
Laserclass IIIa, conform FDA 21 CFR Ch. 1 § 1040
DANGERLASER RADIATION - DO NOT STARE
INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENT
INTO SUNLIGHT620-690 nm/4.95mW max.
CLASS IIIa LASER PRODUCT
Laserclass II, conform FDA 21 CFR Ch. 1 § 1040
CAUTIONLASER RADIATION - DO NOT
STARE INTO BEAM620-690nm/0.95mW max.
CLASS II LASER PRODUCT
26
Japan Surveying Instruments Manufacturers’ Association
Member symbol of the JapanSurveying Instruments Manufacturers’Association representing the highquality surveying products.
Prin
ted
in B
elgi
um
Total Surveying Solutions
022005 First edition TS01401
PENTAX Industrial Instruments Co., Ltd.2-5-2 Higashi-Oizumi
Nerima-ku, Tokyo 178-0063, JapanTel. +81 3 5905 1222Fax +81 3 5905 1225
E-mail: [email protected]: www.pentax.co.jp/piic/survey