electronic components (el t )(elements) · engineering project (engineering project (1) lecture_2...
TRANSCRIPT
Engineering Project (1)Engineering Project (1)
Lecture_2
Electronic Components (El t )(Elements)
Instructor: Eng. IBRAHIM ABU-ISBEIH
6 March 2012 Eng. Ibrahim Abu-Isbeih 1
Objectives:
After completing this class, you will be able fto identify the most commonly used
electronic parts, their symbols, values and names.
6 March 2012 Eng. Ibrahim Abu-Isbeih 2
Passive & Active components
A passive component is an electronic component that does not increase the power of the electrical signal on which it acts.
A passive component may draw the energy it uses for its own operation directly from the signal on which it is operating.
For example, resistors, capacitors,For example, resistors, capacitors, inductors, and transformers are passive components.
6 March 2012 Eng. Ibrahim Abu-Isbeih 3
components.
Passive & Active components
An active component is an electronic fcomponent that does increase the power of
the signal on which it acts. The energy it adds to the signal must be
drawn from a power source other than the signal on which it is operating.
For example, diodes, transistors, andFor example, diodes, transistors, and integrated circuits are active components.
6 March 2012 Eng. Ibrahim Abu-Isbeih 4
Power Supply
The source of emf (electromotivef ) h l f dforce), with a voltage of , measured inunits of volts, V. (e.g. battery, voltage
)source, current source,….).
6 March 2012 Eng. Ibrahim Abu-Isbeih 5
Power Supplies (Batteries):
6 March 2012 Eng. Ibrahim Abu-Isbeih 6
Power Supplies:
6 March 2012 Eng. Ibrahim Abu-Isbeih 7
Resistors A resistor is a two-terminal electrical or electronic
component that resists an electric current bycomponent that resists an electric current byproducing a voltage drop between its terminals inaccordance with Ohm's law: R=V/I.accordance with Ohm s law: R V/I.
The electrical resistance is equal to the voltage drop across the resistor divided by the current p ythrough the resistor. Resistors are used as part of electrical networks and electronic circuits.
The resistor, measured in units of ohms, .However, wires connecting parts of a circuit areeall not esistance f ee
6 March 2012 Eng. Ibrahim Abu-Isbeih 8
really not resistance-free.
Resistor Color Coding
4 Band resistor 5 Band resistor
Tolerance
2nd digitMultiplier 1st digit Multiplier
Tolerance
2nd di it1st digit 3rd digit2nd digit
l i li b fMultiplier = number of zeros
Example: the color Red means 2 zeros or 210
6 March 2012 Eng. Ibrahim Abu-Isbeih 9
C l C d T blColor Code Table:ToleranceCodeColor
10%Silver
5%Gold
0Bl k 0Black
1%1Brown
2%2Red
3%3Orange
4%4Yellow
5Green 5Green
6Blue
7Purple
8Gray
9White
20%No color
6 March 2012 Eng. Ibrahim Abu-Isbeih 10
20%No color
Examples:
:1Ex
Green-Blue–Red - Gold
%5 5600 valueResistance
:2Ex
%108430valueResistance Gray-Yellow-Orange-Brown - Silver
6 March 2012 Eng. Ibrahim Abu-Isbeih 11
%10 8430valueResistance
Resistors:
6 March 2012 Eng. Ibrahim Abu-Isbeih 12
Resistors:Potentiometers
Faders
Variable Resistors
6 March 2012 Eng. Ibrahim Abu-Isbeih 13
Variable Resistors
Inductors:
The inductor, with inductance L, measuredfin units of henrys, H.
Inductance is an effect which results fromthe magnetic field that forms around acurrent carrying conductor.
6 March 2012 Eng. Ibrahim Abu-Isbeih 14
Inductors (Coils):
6 March 2012 Eng. Ibrahim Abu-Isbeih 15
Inductors (Coils):
6 March 2012 Eng. Ibrahim Abu-Isbeih 16
Capacitors (Condensers):
A capacitor is an electrical device that can fstore energy in the electric field between a pair
of closely-spaced conductors (called 'plates'). h l l d hWhen voltage is applied to the capacitor,
electric charges of equal magnitude, but l b ld h lopposite polarity, build up on each plate.
The capacitor, with capacitance C measured in units of farads, F.
6 March 2012 Eng. Ibrahim Abu-Isbeih 17
Capacitors:
Capacitors are used in electrical circuits as energy-storage devices. They can also be used to differentiate between high-frequency and l f l d h k hlow-frequency signals and this makes them useful in electronic filters.
Capacitors are occasionally referred to as condensers.
6 March 2012 Eng. Ibrahim Abu-Isbeih 18
Capacitors:
Electrolytic Capacitors
6 March 2012 Eng. Ibrahim Abu-Isbeih 19
Capacitors:
6 March 2012 Eng. Ibrahim Abu-Isbeih 20
Capacitor Color Codes A color code is used to indicate capacitance
and the tolerance rating of most capacitorsand the tolerance rating of most capacitors. On some, the code also indicated the temperature coefficient and working voltage rating.
It is interesting to note, however, that there is a strong trend on the part of manufacturersis a strong trend on the part of manufacturers to print the capacitance value and the working voltage rating directly on the mostworking voltage rating directly on the most common capacitors, thus eliminating the need for the color code.
6 March 2012 Eng. Ibrahim Abu-Isbeih 21
Capacitors (Example):
6 March 2012 Eng. Ibrahim Abu-Isbeih 22
Transformers:
6 March 2012 Eng. Ibrahim Abu-Isbeih 23
Diodes: A diode is p-n junction formed by combining
N-type and P-type semiconductors together inN type and P type semiconductors together in very close contact.
e.g., Diode, Zener diode, LED, and g , , , ,Photodiode
6 March 2012 Eng. Ibrahim Abu-Isbeih 24
Diodes
6 March 2012 Eng. Ibrahim Abu-Isbeih 25
Diodes:
6 March 2012 Eng. Ibrahim Abu-Isbeih 26
Diodes (LEDs):
6 March 2012 Eng. Ibrahim Abu-Isbeih 27
Diodes (LEDs):
6 March 2012 Eng. Ibrahim Abu-Isbeih 28
Transistors A transistor is a semiconductor device,
commonly used as an amplifiercommonly used as an amplifier. The transistor may be used in a wide variety of
digital and analog functions, includingdigital and analog functions, including amplification, switching, voltage regulation, signal modulation, and oscillators.
b k d d d ll Transistors may be packaged individually or as part of an integrated circuit chip, which may hold thousands of transistors in a very smallhold thousands of transistors in a very small area.
6 March 2012 Eng. Ibrahim Abu-Isbeih 29
Transistors Transistors are divided into two main
categories:categories: Bipolar junction transistors (BJTs) Field effect transistors (FETs).( )
Application of current in BJTs and voltage in pp gFETs between the input and common terminals increases the conductivity between the common and output terminals thereby controllingand output terminals, thereby controlling current flow between them.
6 March 2012 Eng. Ibrahim Abu-Isbeih 30
Transistors BJT symbols:
PNP NPN
JFET symbols:
P-channel N channelP-channel N-channel
6 March 2012 Eng. Ibrahim Abu-Isbeih 31
Transistors (Example) The popular 2N5961 NPN TO-92 Transistor is
shown belowshown below.
This is an excellent transistor to use when low- This is an excellent transistor to use when lownoise, high gain, and low-current are required.
6 March 2012 Eng. Ibrahim Abu-Isbeih 32
Transistors
6 March 2012 Eng. Ibrahim Abu-Isbeih 33
Transistors
6 March 2012 Eng. Ibrahim Abu-Isbeih 34
Operational Amplifiers An operational amplifier IC is a solid-
state integrated circuit that uses externalstate integrated circuit that uses external feedback to control its functions.
The op-amp without any external devices isThe op amp without any external devices is called 'open-loop' mode, referring actually to the so-called 'ideal' operational amplifier with infinite open loop gain inputwith infinite open-loop gain, input resistance, bandwidth and a zero output resistance.resistance.
However, in practice no op-amp can meet these ideal characteristics.
6 March 2012 Eng. Ibrahim Abu-Isbeih 35
Operational Amplifiers The LM741/NE741/uA741 (741 family) Op-
Amps are the most popular oneAmps are the most popular one.
741 Type ICL7612 CMOS O A741-Type ICL7612 CMOS Op Amp
6 March 2012 Eng. Ibrahim Abu-Isbeih 36
Operational Amplifiers
6 March 2012 Eng. Ibrahim Abu-Isbeih 37
741 Op-Amp
6 March 2012 Eng. Ibrahim Abu-Isbeih 38
Photocells A photoresistor is an electronic component
whose resistance decreases with increasing gincident light intensity. It can also be referred to as a light-dependent resistor (LDR), photoconductor, or photocell.p otoco ducto , o p otoce
A photoresistor is made of a high-resistance semiconductor. If light falling on the device is of high enough frequencythe device is of high enough frequency, photons absorbed by the semiconductor give bound electrons enough energy to jump into the conduction band The resulting freethe conduction band. The resulting free electron (and its hole partner) conduct electricity, thereby lowering resistance.
6 March 2012 Eng. Ibrahim Abu-Isbeih 39
Photocells
6 March 2012 Eng. Ibrahim Abu-Isbeih 40
Relays A relay is an electrical switch that opens and
closes under the control of another electricalcloses under the control of another electrical circuit.
The switch is operated by an electromagnet to p y gopen or close one or many sets of contacts.
6 March 2012 Eng. Ibrahim Abu-Isbeih 41
Crystal Oscillators A crystal oscillator is an electronic circuit
that uses the mechanical resonance of athat uses the mechanical resonance of a vibrating crystal of piezoelectric material to create an electrical signal with a very precise ffrequency.
6 March 2012 Eng. Ibrahim Abu-Isbeih 42
Integrated Circuits (ICs) An integrated circuit (also known as IC,
microcircuit microchip silicon chip or chip) ismicrocircuit, microchip, silicon chip, or chip) is an electronic circuit (consisting mainly of semiconductor devices, as well as passive
t ) th t h b f t d icomponents) that has been manufactured in the surface of a thin substrate of semiconductor materialsemiconductor material.
6 March 2012 Eng. Ibrahim Abu-Isbeih 43
Integrated Circuits (ICs) There are two main advantages of ICs over
discrete circuits: cost and performancediscrete circuits: cost and performance. Cost is low because the chips, with all their
components, are printed as a unit by p , p yphotolithography and not constructed a transistor at a time.P f i hi h i th t Performance is high since the components switch quickly and consume little power, because the components are small and closebecause the components are small and close together. Chip areas range from a few square mm to around 350 mm2, with up to 1 million t i t 26 March 2012 Eng. Ibrahim Abu-Isbeih 44
transistors per mm2.
Integrated Circuits (ICs)SSI, MSI, LSI:
The first integrated circuits contained only a few The first integrated circuits contained only a few transistors. Called "Small-Scale Integration" (SSI), they used circuits containing transistors numbering in the tensthe tens.
The next step in the development of integrated circuits, taken in the late 1960s, introduced devices , ,which contained hundreds of transistors on each chip, called "Medium-Scale Integration" (MSI).
Further development driven by the same economic Further development, driven by the same economic factors, led to "Large-Scale Integration" (LSI) in the mid 1970s, with tens of thousands of transistors per chip
6 March 2012 Eng. Ibrahim Abu-Isbeih 45
transistors per chip.
Integrated Circuits (ICs)VLSI:
The final step in the development process starting in The final step in the development process, starting in the 1980s and continuing on, was "Very Large-Scale Integration" (VLSI), with hundreds of tho sands of t ansisto s and be ond ( ell pastthousands of transistors, and beyond (well past several million in the latest stages).
6 March 2012 Eng. Ibrahim Abu-Isbeih 46
Integrated Circuits (ICs)VLSI:
The final step in the development process starting in The final step in the development process, starting in the 1980s and continuing on, was "Very Large-Scale Integration" (VLSI), with hundreds of tho sands of t ansisto s and be ond ( ell pastthousands of transistors, and beyond (well past several million in the latest stages).
6 March 2012 Eng. Ibrahim Abu-Isbeih 47
Integrated Circuits (ICs)ULSI, WSI, SOC:
To reflect further growth of the complexity the term To reflect further growth of the complexity, the term ULSI that stands for "Ultra-Large Scale Integration" was proposed for chips of complexity mo e than 1 million of t ansisto smore than 1 million of transistors.
The most extreme integration technique is wafer-scale integration (WSI), which uses whole uncut g ( ),wafers containing entire computers (processors as well as memory).
The WSI technique failed commercially but advances The WSI technique failed commercially, but advances in semiconductor manufacturing allowed for another attack on IC complexity, known as System-on-Chip(SOC) design
6 March 2012 Eng. Ibrahim Abu-Isbeih 48
(SOC) design.