electrical workshop module2
TRANSCRIPT
-
7/28/2019 Electrical Workshop Module2
1/35
Module-2
Hand Tools
-
7/28/2019 Electrical Workshop Module2
2/35
Identify different hand tools used inworkshops
Understand the basic functions and types ofhand tools.
Be aware of workshop tools safety rules.
-
7/28/2019 Electrical Workshop Module2
3/35
Introduction Common Tools 1.Screwdrivers
2.Wire Strippers
3.Side Cutters 4.Wire Crimpers
Hand Tools Safety Class and Lab Activities
-
7/28/2019 Electrical Workshop Module2
4/35
Hand tools applications
-
7/28/2019 Electrical Workshop Module2
5/35
1.Screwdrivers (Purpose):
insert and tighten screws loosen and remove screws
-
7/28/2019 Electrical Workshop Module2
6/35
Screwdrivers (Types): identified by the shapeof their headinto different types.
-
7/28/2019 Electrical Workshop Module2
7/35
2.Wire strippers (purpose): are small, hand-held devices used to strip the insulation fromelectric wires.
-
7/28/2019 Electrical Workshop Module2
8/35
Wire strippers (types): manual and automatic
-
7/28/2019 Electrical Workshop Module2
9/35
Strip wire with automatic stripper (video)
Activity 3: How to use wire strippers
-
7/28/2019 Electrical Workshop Module2
10/35
Items Required:
Wire stripper Wires
-
7/28/2019 Electrical Workshop Module2
11/35
1.Hold the wire stripper in your hand
2.Put the wire that you want to remove the
insulation from into the jaws of wire stripperup to the length you need
3.Squeeze the handle. The jaw will remove thewire insulation.
4.Once you finish squeezing the handle, releasethe handle and the jaw will open again. SeeFigure
5.Now, the insulation of the wire is removed.
-
7/28/2019 Electrical Workshop Module2
12/35
3.Side Cutters (purpose): used for cuttingextra components leads.
-
7/28/2019 Electrical Workshop Module2
13/35
-
7/28/2019 Electrical Workshop Module2
14/35
4.Wire Crimpers (Purpose):used to connecttwo wires or two conductors together.
-
7/28/2019 Electrical Workshop Module2
15/35
Items Required:
-
7/28/2019 Electrical Workshop Module2
16/35
http://localhost/var/www/apps/conversion/tmp/scratch_7/Crimping%20terminals%20001.flv -
7/28/2019 Electrical Workshop Module2
17/35
How to use a wire crimper to crimp pins
-
7/28/2019 Electrical Workshop Module2
18/35
1.Bend off a pin from the strip
-
7/28/2019 Electrical Workshop Module2
19/35
Insert the stripped wire into the crimp pin as
shown in the picture above.
-
7/28/2019 Electrical Workshop Module2
20/35
Place the crimp into the crimper as shown in the
figure above
-
7/28/2019 Electrical Workshop Module2
21/35
4.Squeeze and insert into housing
-
7/28/2019 Electrical Workshop Module2
22/35
Basic Rules for hand tools Safety: To prevent accidents that are caused by hand tools,
follow the coming tips:
-
7/28/2019 Electrical Workshop Module2
23/35
To prevent accidents that are caused by hand tools,follow the coming tips:
-
7/28/2019 Electrical Workshop Module2
24/35
Indicate the safe and unsafe behavior in the followingpictures. Give Reasons
-
7/28/2019 Electrical Workshop Module2
25/35
Fill in the table below:
-
7/28/2019 Electrical Workshop Module2
26/35
-
7/28/2019 Electrical Workshop Module2
27/35
Items Required:
-
7/28/2019 Electrical Workshop Module2
28/35
Steps: Hold the wire stripper in your
hand Put the wire that you want to
remove the insulation from intothe jaws of wire stripper up tothe length you need
Squeeze the handle. The jawwill remove the wire insulation.
Once you finish squeezing thehandle, release the handle andthe jaw will open again theninsulation of the wire isremoved.
-
7/28/2019 Electrical Workshop Module2
29/35
I am used toremove a screw,who am I ?I am having thehead symbolshown below, whoam I ?
Whoam I?
I am used toconnect twoconductorstogether, who amI?
Who am I? Who am I?
I am having thehead symbolshown below, who am I ?
Who am I? I am used to cutextra electricalleads, who amI?
1 2 3
4 5 6
7 8 9
-
7/28/2019 Electrical Workshop Module2
30/35
Check your tools regularly for wear anddamage
Use the correct tool for the job
Keep your tools clean and in a goodconditions
Use appropriate safety equipments
Keep hands a way from the moving parts
-
7/28/2019 Electrical Workshop Module2
31/35
-
7/28/2019 Electrical Workshop Module2
32/35
1 2
3
-
7/28/2019 Electrical Workshop Module2
33/35
Place the cores into their correct positions as shown
below
Core color Core marking Core position
BROWN Live (L) FUSE (RIGHT HANDPIN)
BLUE Neutral (N) LEFT HAND PIN
GREEN/YELLOW Earth (E) EARTH PIN (TOP)
4
-
7/28/2019 Electrical Workshop Module2
34/35
5 6Video
http://localhost/var/www/apps/conversion/tmp/scratch_7/How%20To%20Re%20Wire%20A%20Plug.flvhttp://localhost/var/www/apps/conversion/tmp/scratch_7/How%20To%20Re%20Wire%20A%20Plug.flv -
7/28/2019 Electrical Workshop Module2
35/35
Be prepared to a Quiz next Class in module#2. Do Worksheets 1 and 2 (From my Wiki). Next Class: Start with Module #3