electric standing desk user manual · 2019. 7. 31. · electric standing desk user manual model:...
TRANSCRIPT
-
Electric Standing Desk
User ManualModel: AIT004B
-
TABLE OF CONTENTS
Parts and Hardware List
Parts
01
02
Hardware 02
Step 1 03
Step 2 03
Step 3 04
Step 4 04
Step 5 05
Step 6 05
06Step 7
06Step 8
07Step 9
08Operation Guide
-
01
PARTS AND HARDWARE LIST
NO Component Name Qty
Top Bracket
Left Leg
ST4.8*25 Screw
Spanner
M6*16 Screw
M6*12 Screw(Black)
Control Box
Key Pad
Foot
Bottom Bracket
Gasket 6
5mm Hex Spanner
4mm Hex Spanner
Rubber Cushion
Plastic
1
2
3
4
5
6
7
A
C
D
E
F
G
H
I
J
K
L
M
2
2
2
1
1
Beam 1
1
Right Leg8 1
Driveshaft9 1
Table Top(1500*370*25)10 1
Table Top(1500*400*25)11 1
8
M6*12 Screw(Silver)B 12
8
1
6
ST4.8*19 Screw 2
ST3.5*19 Screw 2
Cable Tie 5
1
8
1
10
10
2
4
8
5
6 107
11
9
3
1
A B C D
E F G H
I
M
J K L
-
PARTS
HARDWARE
5 Key Pad x1
2 Bottom Bracket x2
6 Beam x1 7 Control Box x1
10 Table Top(1500*370*25)
9 Driveshaft x1
3 Foot x2 4 Left Leg x1
8 Right Leg x1
11 Table Top(1500*400*25)
M6*12Screw x 8
(Black)
4mmSpanner x 1
5mmSpanner x 1
M6*12Screw x 12(Silver)
ST4.8*19Screw x 2
ST4.8*25Screw x 6
ST3.5*19Screw x 2
M6*16Screw x 8
Rubber Cushion x 10
Spannerx 1
Gasket 6 x 8
1 Top Bracket x2
Plastic x 10
Cable Tie x 5 02
A
G
M
H I J K L
B C ED F
-
Attach left leg to the beam using 4pcs M6*12 screws(silver).
STEP 1
Insert hex bar of driving rod into right leg and using spanner to loosen nut on the driving rod to allow the length of the hexagon rod to be stretched.
STEP 2
4mm Hex Spanner M6*12 screws 4 pcs
03
Tool Required:JHardware Required:B Screws
Tool Required:L
Spanner
-
Attach right leg along with driving rod to the beam using 4 pcs M6*12 screws,both ends of the drive rod can not interfere with the crossbeam and right leg.
STEP 3
Install the feet on the leg and fix it using 8 pcs M6*16 screws and gaskets.
5mm Hex Spanner
04
STEP 4
4mm Hex Spanner M6*12 screws (silver)4 pcs
Tool Required:JHardware Required:B Screws
Tool Required:KHardware Required:C & I Screws
M6*16 screws 8 pcs
Gasket 6 8 pcs
-
Install the top bracket on the beam using 4 pcs M6*12 screws (silver) and put 6 rubber cushions into the each hole site of brackets and beam.
STEP 5
STEP6
Using 6 pcs ST4.8*25 screws to fix the table top (1500*370*25) to the frame,using 2pcs ST3.5*19 screws to install the handset and the ST4.8*19 screws to install the control box on the tabletop.
M6*12 4pcs(Silver)
Rubber Cushion 6 pcs Plastic 6 pcs4mm Hex Spanner
ST4.8*25 screw 6 pcs
ST4.8*19 screw 2 pcs
ST3.5*19 screw 2 pcs
Attention:When installing the control box, the power cord interface should be oriented towards the left leg.
05
Tool Required:JHardware Required:B Screws(silver)G & H
Tool Required:Drill / DriverHardware Required:E & D & F Screws
-
STEP 7
Install the top bracket with 8 pcs M6*12 screws(black) and put 4 rubber cushions into the each hole site of brackets and insert the plastic into the rubber pad from the bottom.
STEP 8
4mm Hex Spanner
Rubber Cushion 4 pcs
Plastic 4 pcs
M6*12 8 pcs(Black)
ST4.8*25 Screw 4 pcs
Using 4 pcs ST4.8*25 screws to fix the table top (1500*400*25) to the bottom.
06
Tool Required:JHardware Required:A ScrewsG & H
Tool Required:Drill / DriverHardware Required:
F Screws
-
STEP 9
Connect the motors and handset to the control box,installationcompleted.Use cable tie to hold the spare cable in place.
Hardware Required:MCable Tie
07
-
Operation Guide
08
Activating & Troubleshooting
Lock and Unlock
You will need to activate the memory keypad once the desk is fully assembled, Side note :
if the frame doesn’t seem to be working properly, rest assured that most issues can be
fixed using the exact same activation process.
1.If the handset locked, first step is unlock.
2.Begin by pressing and holding the “Up” and “Down” buttons at the same time.
3.Continue to hold as the frame lowers itself all the way down (if extended ), you will hear a
slight beep sound followed by a brief flash on the display.
4.Press the “Up” button once to engage the motors, your desk should be activated and
ready to go.
Press the lock button for 1 second handset locked.
Press the lock button for 3 seconds handset unlock.
To preset a specific height, drive the desk to desired height, press “Up” and 1 buttons at the
same time for about 2 seconds, “P1” should appear on the display,repeat the procedure for
button 2.
Press “1” “2” and “unlock” button together for about 5 seconds, “C-I” should appear on the
display, press the “2” button you should see “I “ displayed, you have programmed the
handset from centimeters to inches.
Press“1” “2” and “unlock” button together for about 5 seconds, “C-I” should appear on the
display, press the “1” button you should see “C ” displayed, you have programmed the
handset from inches back to centimeters.
Memory Function
Programming Alternative Measurements
Revert Back to Centimeters