electric spin spreader - land pride · electric spin spreader for utility vehicles with 2"...

Cover photo may show optional equipment not supplied with standard unit.

© Copyright 2016 Printed

Read the Accessory manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!

!

Table of Contents

For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Electric Spin Spreader

5/24/16

701-162MAccessory Manual

25609

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1

Look For The Safety Alert Symbol . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Section 1: Assembly & Set-up . . . . . . . . . . . . 4Electric Spin Spreader . . . . . . . . . . . . . . . . . . . . . . . 4

Mount Spreader To A Disc Harrow . . . . . . . . . . . . . 6

Mount Spreader To A Vehicle . . . . . . . . . . . . . . . . . 8

Section 2: Operating Procedures . . . . . . . . . 9Calibrating the Spin Controller . . . . . . . . . . . . . . . . 9

Field Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Daily Operational Checks . . . . . . . . . . . . . . . . . . . 10

Cleaning And Storing . . . . . . . . . . . . . . . . . . . . . . 10

Spin Spreader Discharge Rates . . . . . . . . . . . . . . 10

Narrow Pattern Calculations . . . . . . . . . . . . . . . . 10

Wide Pattern Calculations . . . . . . . . . . . . . . . . . 10

Discharge Rate Table - 4 Ft. Spread Pattern . . . 11



Discharge Rate Table - Wide Spread Pattern . . 14

Section 3: Additional Equipment . . . . . . . . . 15Additional Seeding Equipment . . . . . . . . . . . . . . . 15

Disc Harrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Drag Harrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Seed Bed Roller . . . . . . . . . . . . . . . . . . . . . . . . . 15

Complete One Pass Seeding Application . . . . . . 16

Section 4: Specifications . . . . . . . . . . . . . . . 17Section 5: Features & Benefits . . . . . . . . . . 18Section 6: Troubleshooting . . . . . . . . . . . . . 19Section 7: Appendix . . . . . . . . . . . . . . . . . . . 20

Listing of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Parts Not Used . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH

© Copyright 2016 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed oPride assumes no responsibility for errors or omissions. Neither is any liability assumed forthe right to revise and improve its products as it sees fit. This publication describes the stat

Land Pride is a reg

All other brands and product names are trademarks

Printed in the United

Table of Contents

10, DH15 & DH25 Disc Harrows, and FPS48 701-162M 5/24/16

r implied. While every precaution has been taken in the preparation of this manual, Land damages resulting from the use of the information contained herein. Land Pride reservese of this product at the time of its publication, and may not reflect the product in the future.

istered trademark.

or registered trademarks of their respective holders.

States of America.

Important Safety InformationTable of Contents▲

Important Safety InformationThese are common practices that may or may not be applicable to the products described in
this manual.
!Be Aware of Signal WordsA Signal word designates a degree or level of hazard seriousness. The signal words are:

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded.

! DANGER

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

! WARNING

! CAUTION

Safety at All TimesThoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them.Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.

▲ Operator should be familiar with all functions of the Spin Spreader.

▲ Never allow children to operate equipment.

▲ Operate Spin Spreader from the driver’s seat only.

▲ Make sure all guards and shields are in place and secured before operating the Spin Spreader.

▲ Do not leave Spin Spreader unattended with motor running.

▲ Keep hands, feet, and clothing away from power-driven parts.

▲ Wear snug fitting clothing to avoid entanglement with moving parts.

▲ Operating equipment safely requires the full attention of the operator. Avoid wearing radio headphones while operating the Spin Spreader.

5/24/16 Electric Spin Spreader For utility vehicles with 2" receiver hit

Look For The Safety Alert SymbolThe SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.

Practice Safe Maintenance▲ Understand procedure before doing

work. Use proper tools and equipment, refer to Operator’s Manual for additional information.

▲ Work in a clean dry area.▲ Lower attached implement to the

ground and follow all shutdown procedures before leaving the operator’s seat to perform maintenance.

▲ Allow implement to cool completely before working on it.

▲ Disconnect battery ground cable (-) before servicing or adjusting electrical systems or before welding on implement.

ch, DH10, DH15 &

▲ Do not grease or oil implement while it is in operation.

▲ Inspect all parts. Make sure parts are in good condition & installed properly.

▲ Replace parts on this machine with genuine Land Pride parts only. Do not alter this machine in a way which will adversely affect its performance.

▲ Remove buildup of grease, oil, and debris.

▲ Remove all tools and unused parts from implement before operation.

1 DH25 Disc Harrows, and FPS48

2

Important Safety Information

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48 5/24/16

Table of Contents

These are common practices that may or may not be applicable to the products described in this manual.

Keep Riders Off Machinery▲ Never carry riders or use

machinery as a person lift.▲ Riders obstruct operator’s view. ▲ Riders could be struck by foreign

objects or thrown from the machine.

▲ Never allow children to operate equipment.

Wear Protective Equipment▲ Wear protective clothing and

equipment appropriate for the job such as safety shoes, safety glasses, hard hat, and ear plugs.

▲ Clothing should fit snug without fringes and pull strings to avoid entanglement with moving parts.

▲ Prolonged exposure to loud noise can cause hearing impairment or hearing loss. Wear suitable hearing protection such as earmuffs or earplugs.

▲ Operating equipment safely requires the operator’s full attention. Avoid wearing radio headphones while operating machinery.

Prepare for Emergencies▲ Be prepared if a fire starts.▲ Keep a first aid kit and fire

extinguisher handy.▲ Keep emergency numbers for

doctor, ambulance, hospital, and fire department near phone.

911

Use Seat Belt and ROPS▲ Operate only utility vehicles and

tractors equipped with a Roll-Over Protective Structure (ROPS) and seat belt.

▲ Keep folding ROPS in the “locked up” position at all times.

▲ Fasten seat belt snugly and securely to help protect against serious injury or death from falling and machine overturn.

▲ Wear protective equipment such as a hard hat, safety shoes, safety glasses, and ear plugs.

Use Safety Lights and Devices▲ Slow moving tractors,

self-propelled equipment, and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night.

▲ Flashing warning lights and turn signals are recommended whenever driving on public roads.

Handle Chemicals Properly▲ Protective clothing should be

worn.▲ Handle all chemicals with care. ▲ Follow instructions on container

label.▲ Agricultural chemicals can be

dangerous. Improper use can seriously injure persons, animals, plants, soil, and property.

▲ Inhaling smoke from any type of chemical fire is a serious health hazard.

▲ Store or dispose of unused chemicals as specified by the chemical manufacturer.

IntroductionTable of Contents

Introduction

Land Pride welcomes you to the growing family of new product owners.

This Electric Spin Spreader has been designed with care and built by skilled workers using quality materials. It is exclusively designed to mount on the rear of a small utility vehicle with a 2" receiver hitch such as ATV’s and Land Pride Trekers. Also, it will fit on the back of any Land Pride Disc Harrow, and FPS48. Please thoroughly read these installation instructions, vehicle Operator manual and Disc Harrow Operator Manual before beginning. Especially read information relating to safety concerns.

Proper assembly, maintenance and safe operating practices will help you get years of satisfactory use from your Electric Spin Spreader.

ApplicationThe Land Pride Electric Spin Spreader is a highly versatile full component package designed to plant or spread seeds. It can then be used to spread prilled or granulated fertilizer, lime, gypsum, and other soil conditioning amendments at distances ranging from 4 ft. to 20 ft. It can also be used in the off-season to spread sand or salt for winter icing or slick snow conditions.

This unit has a 12volt remote tether control that can be operated right from the driver’s seat to turn the spreader on or off or to set the seed-gate opening to different application rates.

The Spin Spreader has applications in overseeding of pastures, grassy runways, open areas, roadsides, medians, wild game food plots, hunting clubs, hunting resorts, ranches, farms, game preserves, landscaping, and hobby farming. It also works very well in gardens and nurseries to incorporate fertilizer and pelletized gypsum or lime as soil amendments.

Accessories are available for mounting the spreader to a 2" receiver hitch on a utility vehicle or a Land Pride Disc Harrow. A Land Pride Drag Harrow and Seed Bed Roller can be attached behind the Disc Harrow making your Land Pride Disc Harrow, Spin Spreader, Drag Harrow and Seed Bed Roller a complete seeding package.

General InformationThese instructions apply to:

322-117A ELECTRIC SPIN SPREADER322-100D EXTENSION TUBE, SPIN SPREADER805-035C PIN BENT 1/2 X 3 WITH HAIRPIN322-264A HITCH MOUNT W/REAR HITCH890-975C 2" BALL HITCH 3500LB 3/4 THRD890-971C TOW HOOK (LOAD 10,000 LBS)

5/24/16 Electric Spin Spreader For utility vehicles with 2" receiv

Using This Manual• This Operator’s Manual is designed to help familiarize

you with safety, assembly, operation, adjustments, troubleshooting, and maintenance. Read this manual and follow the recommendations to help ensure safe and efficient operation.

• The information contained within this manual was current at the time of printing. Some parts may change slightly to assure you of the best performance.

• To order a new manual contact your authorized dealer. Manuals can also be downloaded, free-of-charge from our website at www.landpride.com or printed from the Land Pride Service & Support Center by your dealer.

Owner AssistanceIf customer service or repair parts are required contact a Land Pride dealer. A dealer has trained personnel, repair parts and equipment needed to service the Electric Spin Spreader.

The parts on your Electric Spin Spreader have been specially designed and should only be replaced with genuine Land Pride parts. Therefore, should your Spin Spreader require replacement parts go to your Land Pride Dealer.

Your dealer wants you to be satisfied with your new Electric Spin Spreader. If for any reason you do not understand any part of this manual or are not satisfied with the service received, the following actions are suggested:

1. Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you.

2. If you are still not satisfied, seek out the owner or general manager of the dealership, explain the problem and request assistance.

3. For further assistance write to:

Land Pride Service Department1525 East North Street

P.O. Box 5060Salina, Ks. 67402-5060

E-mail [email protected]

3er hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Section 1: Assembly & Set-upTable of Contents

10. Slide spreader tank (#19) between left and right-Section 1: Assembly & Set-up
Electric Spin Spreader Refer to Figure 1-1 on page 5:322-117A ELECTRIC SPIN SPREADERA detailed listing of parts for the Spin Spreader is provided on page 22. Use the list as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware.
Install the Electric Spin Spreader as follows:

1. Remove Spin Spreader and all component from the shipping boxes.

2. Attach spin motor (#16) to hitch weldment (#34) with flat washers (#28) and 10-32 hex nuts (#27). Tighten hex nuts to the correct torque.

3. Attach spreader distribution plate (#15) to the motor shaft with cotter pin (#14). Spread one or more legs of cotter pin to keep it from falling out.

4. Attach spreader back plate (#31) to spreader hitch weldment (#34) with 8-32 x 2" Phillips head screws (#36) and hex nylock nuts (#35). Tighten nylock nuts. See “NOTE” under “Parts Not Used” on page 25 for shipping location of nylock nuts (#35) and screws (#36).

5. Attach left-hand and right-hand straps (#29 & #30) to hitch weldment (#34) as shown with 5/16"-18 x 2 1/2" GR5 lower bolt (#23) and nylock nut (#25). Screw nut on 2 or 3 turns. Do not tighten at this time.

6. Attach left-hand and right-hand straps (#29 & #30) to hitch weldment (#34) as shown with 5/16"-18 x 3" GR5 all thread upper bolt (#22) and nylock nut (#25). Screw nut on 2 or 3 turns. Do not tighten at this time.

7. Attach left-hand and right-hand straps (#29 & #30) together at the back with 5/16"-18 x 3" GR5 all thread bolt (#22), 3/4" long spacer (#21), and nylock nut (#25). Screw nut on 2 or 3 turns. Do not tighten at this time.

8. Attach Flow regulator (#18) directly below hole “H” in spreader tank (#1) as shown with 8-32 hex nuts (#2A). Tighten hex nuts.

9. (Optional) Attach restrictor plate (#3) on top of existing nuts (#2A) with 8-32 hex huts (#2B). Tighten nuts.

NOTE: Not all components included in the shipping box will be used. See “Parts Not Used” on page 25.

IMPORTANT: Drive “G” for Flow regulator (#18) is located directly below hole “H” in spreader tank (#19).

NOTE: The restrictor plate (#3) is used to decrease the discharge rate of product flow out the two hopper openings. Some applications will require that the restrictor plate be removed. Other applications will require that the restrictor plate be installed.

4 Electric Spin Spreader For utility vehicles with 2" receiver

hand straps (#29 & #30).

11. Hand screw 1/2"-13 hex nut (#24) on eye bolt (#33) until nut has bottomed out on the threads.

12. Insert eye bolt (#33) through hitch weldment (#34), hole “H” in tank (#19), formed washer (#37), and hex nylock nut (#26). Draw nylock nut up until 1 to 2 threads are pass the nylock nut. Do not tighten nut (#24) or nylock nut (#26) at this time.

13. Adjust left-hand and right-hand straps (#29 & #30) to fit between beads in spreader tank (#1) and tighten the front two 5/16"-18 hex nylock nuts (#25) to the correct torque for GR5 bolts and then the back nylock nut (#25) to the correct torque.

14. Hold eye in eye bolt (#33) vertical with a screwdriver or drive punch and tighten nylock nut (#24) against hitch weldment (#34) until tight.

15. Insert wiring for spin motor (#16) into wire clip (#7) as shown with mounting holes in clip up. Skid to step 17 if attaching spin deflector (#4).

16. Attach wire clip (#7) on inside of channel to hole “F” with 1/4"-20 x 3/4" GR5 hex flange serrated screw (#8), flat washer (#6), and wing nut (#5). Hand tighten wing nut. Skip to step 18.

17. Attach optional spin deflector as follows:

a. Attach spin deflector (#4) and wire clip (#7) on inside of channel to hole “F” with 1/4"-20 x 3/4" GR5 hex flange serrated screw (#8), flat washer (#6), and wing nut (#5). Hand tighten wing nut.

b. Complete attachment of spin deflector (#4) to the remaining 3 holes using 1/4"-20 x 3/4" GR5 hex flange serrated screws (#8), flat washers (#6), and wing nuts (#5). Hand tighten wing nuts

18. Fully insert cap plug (#12) in tank lid (#20) as shown.

19. Attach tank lid (#20) to spreader hopper (#19).

20. Attach large square tube cap (#32) to top of hitch weldment tube “J”.

21. Cable ties (#11), hand control (#17), and tie down straps (#13) will be installed after mounting the Spin Spreader to a FPS, utility vehicle, or disc harrow.

NOTE: Spin deflector (#4) is used to reduce the broadcast spread pattern to as small as 48". Install the spin deflector only if a desired spread pattern width is needed.

Installation Note: The spin deflector (#4) can be installed without removing the hopper from its mount. Simply slide the deflector between hopper (#19) and spin plate (#15).

IMPORTANT: Tie down straps (#13) must be used with spreader to protect against damage to spreader and supporting structures.

hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48 5/24/16

5

Section 1: Assembly & Set-up

5/24/16 Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Figure 1-1

25786


Mount Spreader To A Disc HarrowRefer to Figure 1-2 on page 7:322-264A Hitch Mount With Rear Hitch for Disc HarrowA detailed listing of parts for the hitch mount and rear hitch is provided on page 24. Use the list as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware.

1. Park Disc Harrow on a flat surface, move gear shift lever to park or to neutral and set park brake, turn engine switch to off and remove ignition key.

2. Attach spin spreader mounting bracket (#22) to the Disc Harrow rear cross tube (M) with two 3/8"-16 U-bolts (#23 or #24 or #25) and two 3/8" flange lock nuts (#26). See note above. Make certain the bracket is centered on the tube and then tighten U-bolts to the correct torque.

3. Slide spreader mounting bracket (G) over Spin Spreader extension tube (#22). Secure in place with 5/16" x 2 1/2" clevis pin (#9) and hair pin cotter (#10).

4. Attach one end of each ratchet tie down straps (#13) to the spreader eyebolt (L) and the other ends to the Disc Harrow in a V-pattern as shown.

5. Tighten tie down straps to prevent spreader box from jiggling in its mount. Do not over tighten.

6. Plug hand control white connector (A) into feedgate connector (B).

7. Plug hand control black connector (C) into spin motor connector (D).

8. Plug lighter plug (E) into a 12 volt accessory receptacle.

9. Secure wiring harness for controller (#15) with cable ties (#11).

10. Attach rear hitch (#27) to spreader mount (#22) with 3/4" clevis pins (#28) and 5/32" cotter pins (#29). Bend one leg of each cotter pin to keep it in place.

NOTE: Hardware bag consist of 3 different sizes of U-bolts. Use the correct U-bolt size that matches the Disc Harrow rear cross tube.• DH10 Series (#23) U-bolt 3/8"-16 x 2 x 2 3/4"

• DH15 Series (#24) U-bolt 3/8"-16 x 3 1/32 x 3 1/2"

• DH25 Series (#25) U-bolt 3/8"-16 x 3 1/32 x 4"


IMPORTANT: Not securing Spin Spreader with tie down straps will result in MOUNT DAMAGE.


11. Attach one of three hitches listed below to the rear hitch tube. See page 24 for a detailed listing of parts.

Hitch Plate (Standard)a. Attach hitch plate (#32) to rear hitch tube (#27)

with 1/2"-13 x 3 1/2" GR5 hex flange screw s(#30) and hex flange lock nuts (#31).

b. Tighten lock nuts to the correct torque.

c. Insert 3/8" x 5 1/8" long detent hitch pin (#33) into hitch plate (#32).

2" Ball Hitch Part No. 890-975C (Option)a. Attach hitch plate (#32) to rear hitch tube (#27)

per instructions above.

b. Attach 2" ball (#35) to hitch plate (#32).

c. Tighten ball nut to the correct torque.

Tow Hook Part No. 890-971C (Option)a. Remove hitch plate (#32).

b. Attach tow hook (#34) to rear hitch tube (#27) with 1/2"-13 x 3 1/2" GR5 hex flange screws (#30) and hex flange lock nuts (#31).

c. Tighten lock nuts to the correct torque.


7

Section 1: Assembly & Set-up


Table of Contents

Figure 1-2

25788

25788


25787

Mount Spreader To A VehicleRefer to Figure 1-3:A detailed listing of parts for the extension tube (#18) & bent pin (#19) is provided on page 24. Use the list as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware.

1. Park vehicle on a flat surface, move gear shift lever to park or to neutral and set park brake, turn engine switch to off and remove ignition key.

2. Attach Spin Spreader extension tube (#18) to your vehicle’s 2" receiver hitch with bent pin (#19). Secure with hair pin cotter included with the bent pin.

3. Slide spreader mounting bracket (G) over Spin Spreader extension tube (#18). Secure in place with 5/16" x 2 1/2" clevis pin (#9) and hair pin cotter (#10).


Figur


4. Attach one end of each ratchet tie down strap (#13) to the spreader eyebolt (L) and the other ends to the vehicle in a V-pattern as shown.

5. Tighten tie down straps to prevent spreader box from jiggling in its mount. Do not over tighten.

6. Plug hand control white connector (A) into feedgate connector (B).

7. Plug hand control black connector (C) into spin motor connector (D).

8. Plug lighter plug (E) into a 12 volt accessory receptacle.

9. Secure controller wiring harness (#15) with cable ties (#11).

IMPORTANT: Not securing Spin Spreader with tie down straps will result in MOUNT DAMAGE.

e 1-3


Section 2: Operating ProceduresTable of Contents

Calibrating the Spin Controller Field Set-upSection 2: Operating Procedures

Refer to Figure 2-4:

Spin Spreader ControlFigure 2-4

1. Thoroughly lubricate the spreader before calibrating.

2. Calibrate the control unit by holding the OFF button down and momentarily pressing the ON button. While in the calibration mode, the lights will flash rapidly. Once calibration is complete, the lights will go out and the gate will close. The unit is now ready for operation.

3. Set dispensing amount by pressing the MORE or LESS buttons to achieve the desired gate opening. Position 1 is the minimum amount and position 6 is the maximum amount of material flow. The Material Flow light flashes when unit is not running (OFF) and is on solid when unit is running (ON).

4. While moving at a constant rate, start material spreading by pressing the ON button.

5. Press the OFF button to stop the spin motor and close the control gate.

IMPORTANT: To assure proper operation, the Electric Spin Spreader controls should be calibrated each time it is plugged into the 12 volt receptacle or if you loose power to receptacle.

IMPORTANT: Make sure the Spin Spreader is empty and the vehicle is running when calibrating.

23910

NOTE: The MORE or LESS buttons may be pressed at anytime to achieve the desired material flow rate.


! CAUTIONWear eye protection to prevent getting chemicals and/or dirt in the eyes while cleaning the Electric Spin Spreader.

! CAUTIONBe sure to wear proper protective clothing when servicing or lubricating your spin seeder. Refer to chemical manufacturers’ labels for specific clothing requirements.

1. Prior to operation, thoroughly lubricate the Spin Spreader. Check for proper operation of the mechanisms by running the spin motor and slide gate at no-load. See “Calibrating the Spin Controller” on this page.

2. Review spreader rate tables on pages 11 through 14. Make initial setting at the controller (positions 1 through 6) and install or remove the restrictor plate as needed.

3. Install the spin deflector if a narrow pattern is desired or remove the spin deflector if a full width pattern is preferred.

4. Press the OFF button to make sure the Spin Spreader gate is closed and then fill the bin with product.

5. Make a run with the Spin Spreader turned on to check product dispersion rate.

IMPORTANT: Always make sure you are traveling before turning the Spin Spreader on. Always turn the Spin Spreader off before end of travel. Running the spreader while not traveling will discharge too much material in one spot.

NOTE: A good method for checking product dispersion is to fill the bin with the required pounds of material to cover 1,000 sq. ft. in a straight run. A 4 ft. wide pattern would require 250 ft. of straight run. You should run out of product at the end of the 250 ft. If not, make the following adjustments:

1. Increase travel speed to disperse less product per sq. ft. or decrease speed to disperse more.

2. If the speed you are traveling is preferred, change position number on the controller to disperse more or less product.

3. You may also want to adjust the spin deflector at the wing nuts to control placement of product.

4. Make a new run to recheck dispersion rate.



Daily Operational Checks1. Clean the unit of dirt and trash to minimize rusting

and wear.

2. Visually inspect all nuts for tightness.

3. Replace any decals that are worn or damaged.

4. Prior to operation, thoroughly lubricate the Spin Spreader.

5. Check for proper operation of the mechanisms by running the machine at no-load for a few minutes.

6. Calibrate spin controller and spin deflector for spreading the quantity desired and recheck adjustments for accuracy.

7. All spreader parts must be cleaned properly after every use to extend its life and efficiency.

Cleaning And Storing

! CAUTIONWear eye protection to prevent getting chemicals and/or dirt in the eyes while cleaning the Spin Spreader.

! CAUTIONBe sure to wear proper protective clothing when servicing or lubricating your Fertilizer Spreader. Refer to chemical manufacturers’ labels for specific clothing requirements.

Fertilizer is extremely corrosive and all remaining particles including dust particles should be removed from the spreader soon after application.

1. Remove all product left in the holding tank.

2. Disconnect and store spin controller in a dry location.

3. DO NOT wash the feedgate with water. Remove the two screws from the bottom of the gate and slide the gate forward until it drops off the unit. Be careful not to loose the screws.

4. Use a soft bristle brush to clean the felt and remove any dust from around the gear or on the felt.

5. Completely wash the rest of the Spin Spreader with water and dry thoroughly.

6. Add a light coat of oil on all metal parts and motor to help prevent rusting and corrosion.

7. Reinstall the feedgate.

8. Store the Electric Spin Spreader and electrical controls in a location that is sheltered from moisture.

Spin Spreader Discharge RatesDISCLAIMER: The Discharge Rate Tables are intended as guidelines only. Land Pride accepts no responsibility for actual site application rates or germination rates.

IMPORTANT: Remove spin controller and discharge gate before washing the Spin Spreader.

These rates can vary dramatically due to varying conditions and operator skill level.

Narrow Pattern CalculationsCalculations in the Discharge Rate Tables on page 11 for narrow patterns (4’, 5’ & 6’ widths) are based on:

• With and without a restrictor plate installed.

• With the spin deflector attached.

• Dispersal pattern at 48" width.

• Traveling at 1 MPH (mile per hour)

EXAMPLE:If you are traveling 1 MPH and dispersing a 4’ wide pattern of alfalfa using flow position 2, your discharge rate is 515.63 lbs/acre or 11.84 lbs/1000 sq. ft. at 1 MPH (See Discharge Rate Table on page 11). If you are driving at 4 MPH, calculate the discharge rate as follows:

• Divide 515.63 by 4 = 128.91 lbs/acre.

• Divide 11.84 by 4 = 2.96 lbs/1000 sq. ft.

REMEMBER: Increasing travel speed decreases the amount of material being applied.

Wide Pattern CalculationsCalculations in the Discharge Rate Tables on page 14 for the wide pattern spreader rates are based on:

• With the spin deflector removed.

• With and without a restrictor plate installed.

• Dispersal pattern at widths indicated in the table.

• Traveling at 1 MPH (mile per hour)

EXAMPLE:If you are traveling 1 MPH and dispersing a 4’ wide pattern of alfalfa using flow position 2, your discharge rate is 103.13 lbs/acre or 2.37 lbs/1000 sq. ft. at 1 MPH (See Spreader Rate table on page 14). If you are driving at 5 MPH, calculate the discharge rate as follows:

• Divide 103.13 by 5 = 20.63 lbs/acre.

• Divide 2.37 by 5 = 0.47 lbs/1000 sq. ft.

REMEMBER: Increasing travel speed decreases the amount of material being applied.

NOTE: If vehicle does not have a speed meter or no way to calculate speed, a hand held Global Positioning System (GPS) that indicates speed is available at most sporting goods stores.

NOTE: Data in the Discharge Rate Tables is based on traveling at 1 MPH. To calculate discharge rate when traveling at a different speed, divide the data in the table by the MPH you are traveling.

NOTE: Data in the Discharge Rate Tables is based on traveling at 1 MPH. To calculate discharge rate when traveling at a different speed, divide the data in the table by the MPH you are traveling.


11Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Discharge Rate Table - 4 Ft. Spread Pattern @ 1 MPM Alfalfa Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 129.94 515.63 1108.80 1817.06 2003.93 1989.90Lbs/1000 sq. ft. 2.98 11.84 25.45 41.71 46.00 45.68

Unrestricted Restrictor required (See above data with restrictor)

Biologic Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 100.65 312.68 405.08 481.80

Lbs/1000 sq. ft. 0.00 0.00 2.31 7.18 9.30 11.06Unrestricted Lbs/acre 0.00 41.25 154.28 348.98 644.33 1574.10

Lbs/1000 sq. ft. 0.00 0.95 3.54 8.01 14.79 36.14

MegaPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 821.29 1884.30Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 18.85 43.26

EasyPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Clover (Ladina) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 147.26 620.40 1161.60 1908.64 2101.28 2151.60

Lbs/1000 sq. ft. 3.38 14.24 26.67 43.82 48.24 49.39Unrestricted Restrictor required (See above data with restrictor)

Clover (Red) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 92.81 348.56 750.34 1256.06 1499.44 1835.63


Clover (Yellow Sweet) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 482.63 1586.48 1701.98 1706.51 1715.18 1805.10


Oats Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Ryegrass (annual) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 121.28 358.05 469.84 502.43 525.94


Lbs/1000 sq. ft. 0.00 8.34 22.95 41.55 78.30 0.00

Sorghum Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 215.74 614.63 1001.96 1041.56 1059.71


Soybeans Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Gypsum (pelletized) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Prilled Fertilizer Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 852.23 1196.25 1228.84 1234.61


Lbs/1000 sq. ft. 0.00 17.05 49.32 97.44 155.23 165.57

Sand Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 573.79 1564.20 2047.65 2716.73


Lbs/1000 sq. ft. 0.00 0.00 35.27 92.99 124.96 164.24

Salt Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 593.59 972.68 1060.13 1133.96


Lbs/1000 sq. ft. 0.00 19.48 79.45 157.42 225.45 241.36

5/24/16








Lbs/1000 sq. ft. 0.00 .76 2.83 6.41 11.83 28.91















Lbs/1000 sq. ft. 0.00 6.67 18.36 33.24 62.64 0.00




Unrestricted Lbs/acre L0.00 0.00 0.00 0.00 0.00 1233.21Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 28.31





Lbs/1000 sq. ft. 0.00 13.64 39.46 77.95 124.18 132.46



Lbs/1000 sq. ft. 0.00 0.00 28.22 74.39 99.97 131.39



Lbs/1000 sq. ft. 0.00 15.58 63.56 125.49 180.36 193.09

12


13Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48






Lbs/1000 sq. ft. 0.00 .63 2.36 5.34 9.86 24.09















Lbs/1000 sq. ft. 0.00 5.56 15.30 27.70 52.20 0.00









Lbs/1000 sq. ft. 0.00 11.37 32.88 64.96 103.49 110.38



Lbs/1000 sq. ft. 0.00 0.00 23.51 61.99 83.31 109.49



Lbs/1000 sq. ft. 0.00 12.99 52.97 104.95 150.30 160.91

5/24/16



Discharge Rate Table - Wide Spread Pattern @ 1 MPM Alfalfa (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6



Biologic (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 20.13 62.54 81.02 96.36


Lbs/1000 sq. ft. 0.00 .19 0.71 1.60 2.96 7.23

MegaPlot (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


EasyPlot (12 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Clover (Ladina) (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 29.45 124.08 232.32 381.73 420.26 430.32


Clover (Red) (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 18.56 69.7 150.07 251.21 299.89 367.13


Clover (Yellow Sweet) (20 ft.Spread Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 96.53 317.30 340.40 341.30 343.04 361.02


Oats (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Ryegrass (annual) (12 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 40.43 119.35 156.61 167.48 175.31


Lbs/1000 sq. ft. 0.00 2.78 7.65 13.85 26.10 0.00

Sorghum (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 34.52 98.34 160.31 166.65 169.55


Soybeans (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Gypsum (pelletized) (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Not Compatible with restrictor


Prilled Fertilizer (21 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 162.33 227.86 234.06 235.16


Lbs/1000 sq. ft. 0.00 3.25 9.39 18.56 29.57 31.54

Sand (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 91.81 250.27 327.62 434.68


Lbs/1000 sq. ft. 0.00 0.00 5.64 14.88 19.99 26.28

Salt (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6W/Restrictor Lbs/acre 0.00 0.00 94.97 155.63 169.62 181.43


Lbs/1000 sq. ft. 0.00 3.12 12.71 25.19 36.07 38.62

14

Section 3: Additional EquipmentTable of Contents

Section 3: Additional Equipment
Additional Seeding EquipmentDisc HarrowRefer to Figure 3-1:Land Pride Disc Harrows are designed to open and break up soil surface in preparation for planting.
Land Pride Disc Harrow ModelsModel DH1048 & DH1060 . . . . . . . . . 48" & 60" WideModel DH1560 & DH1572 . . . . . . . . . .60" & 72" wideModel DH2572 & DH2584 . . . . . . . . . .72" & 84" wide

Additional equipment can be attached behind the Disc Harrow to make it a complete seeding package. See “Complete One Pass Seeding Application” on page 16.

Electric Spin Spreader Assembly (DH Series)Figure 3-1

Drag HarrowRefer to Figure 3-2: The Land Pride Drag Harrows are designed for various types of seedbed and ground preparations. They can be used to smooth out freshly cultivated soil, work seed and fertilizer into freshly cultivated soil or into turf and pasture grass, fluff and level arenas, aerate soil for faster dry-down time, de-thatch and aerate lawns and pastures, break up aeration cores on turf surfaces and groom snow-packed ski resorts.

The Drag Harrow can also be used in tandem with Land Pride’s Disc Harrow, Electric Spin Spreader and Seed Bed Roller to provide a highly efficient and complete seeding application in one pass. See “Complete One Pass Seeding Application” on page 16.

Land Pride Drag Harrow ModelsModel DRG04 . . . . . . . . . . . . . . . . 4 ft. wide x 4 ft. longModel DRG06 . . . . . . . . . . . . . . . . 6 ft. wide x 4 ft. longModel DRG08 . . . . . . . . . . . . . . . 8 ft. wide x 4 ft. long


Drag Harrow (6’ x 4’ Shown)Figure 3-2

Seed Bed RollerRefer to Figure 3-3:The Land Pride SBR72 Three-point hitch or pull type Seed Bed Roller has uses and applications in landscaping, sports field maintenance, pasture maintenance, professional turf care, general seeding and overseeding applications around home sites, construction sites, horse paddocks, nurseries, sod farms, and small farm or ranch operations. The SBR72 will break up smaller clumps and dirt clods, while pressing applied seed into firm contact with the soil profile for greatly improved germination rates. The notched profile of the roller also develops a pattern of uniformly spaced mini-furrows that tend to hold seed and fertilizer in place. These small furrows also retain essential moisture, and resist erosion from the wind and runoff from applied irrigation or rain. It can be pulled behind the Electric Spin Spreader or behind any machine equipped with a drawbar or receiver hitch. The hitch on the tongue can be set-up as a clevis hitch or turned around for a ball hitch.

SBR72 Set-up for Pull Type Hook-UpFigure 3-3

25611

25762


Section 3: Additional EquipmentTable of Contents

Refer to Figure 3-4:Remove the tongue and rotate the remaining A-frame hitch up 90 degrees and it becomes a 3-point mounted Seed Bed Roller.

SBR72 Set-up for 3-Point Hook-UpFigure 3-4

25763


Complete One Pass Figur

Complete One Pass Seeding ApplicationRefer to Figure 3-5:Land Prides offers a Seeder/Overseeder component system for one-pass ground cultivation and seed to soil integration for applications on previously tilled soil, existing pasture ground, large grassy areas, reclamation sites and wild game food plots. This system is comprised of a Land Pride DH10, DH15 or DH25 Series Disc Harrow, rear mounted Electric Spin Spreader with special hitch kit, trailing DRG04, DRG06 or DRG08 Drag Harrow, and trailing pull-type SBR72 Seed Bed Roller.

See your nearest Land Pride Dealer for more information or visit our web site at www.landpride.com.


Seeding Applicatione 3-5

Section 4: SpecificationsTable of Contents

Section 4: Specifications


Electric Spin Spreader SpecificationsDescription Specification

Spin Spreader Volume/Capacity 2 cu. ft. (15 gallons) (100 lbs. Maximum capacity weight)

Hopper Construction Poly with water tight poly press fit lid.

Deflector Ring Construction Poly construction and removable and adjustable.

Frame Construction Welded and formed steel tubing and sheet metal.

Wide Spread PatternWithout Deflector

20 to 25 ft. (Actual spread pattern is dependent upon product type and condition during application.)

Spin Spreader Deflector Diverts and restricts seed to smaller spreading width. Seed rate tables calculated at 48", 60" & 72" spread width.

Small Seed Restrictor Plate Restricts distribution rate of smaller seeds and doubles the number of calibration settings when installed.

Remote Tether Control ON/OFF Control Button, Numeric Seed gate Calibration Settings, and Plus or Minus Seed Gate Control Function.

Spin Spreader Electrical

Voltage Input 12 volt system with mail power plug for Power Point attachment.

Fuse Rating In line fuse for 15amps maximum.

Start-Up Amps 4 Amp surge for spreading.

Normal Operating Amps .5 Amps for spreading.

Section 5: Features & BenefitsTable of Contents

Section 5: Features & Benefits

18 Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48 5/24/16

Electric Spin SpreaderDescription Benefits

Water Tight Poly Hopper Protects seed and fertilizers from moisture and rodents. Poly construction provides for low unit weight, quiet operation, and resists corrosion.

Small Seed Restrictor Plate Enables applications of smaller seeds without waste. Doubles the number of possible application rates over similar competitive models.

Removable and Adjustable Flinger Ring

Keeps seed or applied products contained to actual width of soil cultivation for reduced waste. Ring removal enables highly productive wide area broadcast of fertilizer, gypsum, lime, sand or salt.

Electronic Tether Control Enables easy and convenient control of on/off function and seed gate application rates right from the seat of the traction unit.

Standard Application Rate Chart

Enables customers to determine spreader settings with confidence and ease. Similar competitive models don’t supply rate charts and require costly and wasteful experimentation to determine proper calibration settings.

Versatile Mounting Systems Provides capabilities for mounting spreaders on a wide range of discs, tractors utility vehicles, ATVs, and pickups.

12 Volt Operating System Enables attachment to a broad range of lower priced traction units equipped with 12 volt power outlets.

Low Unit Weight Provides for easy one-person installation and removal

Section 6: TroubleshootingTable of Contents

Section 6: Troubleshooting


Troubleshooting ChartProblems Cause Solution

Faulty Electrical Wiring

(Electrical components won’t operate. Also see electrical component below.)

Electrical fuse is bad. Replace any bad fuse.

Electrical wiring connections have become disconnected.

Reconnect all connections.

Electrical connections are dirty or corroded. Clean all connections and reconnect. Replace any connections that is corroded beyond cleaning.

Insulation is worn allowing bare wire to make contact with metal.

Cover exposed wiring with electrical tape or replace wiring.

Electrical wiring is cut or broken inside insulation.

Splice or replace wiring.

Spin Spreader gate won’t open/close.

Electrical wiring is at fault. See Problems: “Faulty Electrical Wiring”.

Spin Spreader controls are in need of calibration.

Calibrate Spin Spreader controls.

Gate is stuck. Clean gate and gate track.

Control unit is faulty. Replace Wire Harness.

Spin Spreader motor won’t operate.

Electrical wiring is at fault. See Problems: “Faulty Electrical Wiring”.

Motor is in need of repair or replacement. See your nearest Land Pride Dealer.

Control unit is faulty. Replace Wire Harness.

Spin Spreader discharge pattern is more than 48"

Spin deflector is not attached. Attach spin deflector.

Spin deflector is not adjusted. Attach spin deflector.

Spin deflector is worn. Replace spin deflector.

Spin Spreader discharge pattern is less than it should be.

Spin plate is worn or broken Replace spin plate.

Spin motor does not operate. See Problems: “Spin motor won’t operate”.

Spin deflector is attached. Remove Spin deflector.

Spin Spreader is not discharging enough product.

Material flow setting to too low. Increase Material Flow setting.

Ground speed is too fast. Decrease vehicle speed.

Product size is too large. Remove Restrictor Plate in hopper.

Spin Spreader discharges too much product.

Material flow setting to too high. Decrease Material Flow setting.

Ground speed is too slow. Increase vehicle speed.

Product size is too small. Install Restrictor Plate in hopper.

Ground speed unknown No Speedometer or table indicating MPH Purchase a Global Positioning System (GPS) with speed capabilities in miles per hour (MPH)

Section 7: AppendixTable of Contents

Section 7: Appendix


Torque Values Chart for Common Bolt SizesBolt Head Identification Bolt Head Identification

Bolt Size (inches) Grade 2 Grade 5 Grade 8

Bolt Size(Metric) Class 5.8 Class 8.8 Class 10.9

in-tpi 1 N · m 2 ft-lb 3 N · m ft-lb N · m ft-lb mm x pitch 4 N · m ft-lb N · m ft-lb N · m ft-lb

1/4" - 20 7.4 5.6 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7

1/4" - 28 8.5 6 13 10 18 14 M 6 X 1 7 5 11 8 15 11

5/16" - 18 15 11 24 17 33 25 M 8 X 1.25 17 12 26 19 36 27

5/16" - 24 17 13 26 19 37 27 M 8 X 1 18 13 28 21 39 29

3/8" - 16 27 20 42 31 59 44 M10 X 1.5 33 24 52 39 72 53

3/8" - 24 31 22 47 35 67 49 M10 X 0.75 39 29 61 45 85 62

7/16" - 14 43 32 67 49 95 70 M12 X 1.75 58 42 91 67 125 93

7/16" - 20 49 36 75 55 105 78 M12 X 1.5 60 44 95 70 130 97

1/2" - 13 66 49 105 76 145 105 M12 X 1 90 66 105 77 145 105

1/2" - 20 75 55 115 85 165 120 M14 X 2 92 68 145 105 200 150

9/16" - 12 95 70 150 110 210 155 M14 X 1.5 99 73 155 115 l215 160

9/16" - 18 105 79 165 120 235 170 M16 X 2 145 105 225 165 315 230

5/8" - 11 130 97 205 150 285 210 M16 X 1.5 155 115 240 180 335 245

5/8" - 18 150 110 230 170 325 240 M18 X 2.5 195 145 310 230 405 300

3/4" - 10 235 170 360 265 510 375 M18 X 1.5 220 165 350 260 485 355

3/4" - 16 260 190 405 295 570 420 M20 X 2.5 280 205 440 325 610 450

7/8" - 9 225 165 585 430 820 605 M20 X 1.5 310 230 650 480 900 665

7/8" - 14 250 185 640 475 905 670 M24 X 3 480 355 760 560 1050 780

1" - 8 340 250 875 645 1230 910 M24 X 2 525 390 830 610 1150 845

1" - 12 370 275 955 705 1350 995 M30 X 3.5 960 705 1510 1120 2100 1550

1-1/8" - 7 480 355 1080 795 1750 1290 M30 X 2 1060 785 1680 1240 2320 1710

1-1/8" - 12 540 395 1210 890 1960 1440 M36 X 3.5 1730 1270 2650 1950 3660 2700

1-1/4" - 7 680 500 1520 1120 2460 1820 M36 X 2 1880 1380 2960 2190 4100 3220

1-1/4" - 12 750 555 1680 1240 2730 2010 1 in-tpi = nominal thread diameter in inches-threads per inch

1-3/8" - 6 890 655 1990 1470 3230 2380 2 N· m = newton-meters

1-3/8" - 12 1010 745 2270 1670 3680 2710 3 ft-lb= foot pounds

1-1/2" - 6 1180 870 2640 1950 4290 3160 4 mm x pitch = nominal thread diameter in millimeters x thread pitch1-1/2" - 12 1330 980 2970 2190 4820 3560

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

5.8 8.8 10.9

21

Section 7: Appendix


Table of Contents

Notes


Listing of PartsA detailed list of parts is provided below and on page. Use the parts list as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware.

Part No. 322-117A Electric Spin Spreader


Refer to Figure 8 on page 23:1 701-162M MANUAL, ELECTRIC SPIN SPREADER

1 1 840-246C FERT/SEED SPREADER, ATV . . . . . . . . . . . . (Includes items 14 through 20 below)2 2 803-064C NUT HEX 8-323 1 322-106D RESTRICTOR SMALL SEED4 1 817-706C DEFLECTOR SPIN SPREADER5 4 803-202C NUT WING 1/4-20 PLT6 4 804-007C WASHER FLAT 1/4 SAE PLT7 1 800-347C WIRING/TUBE CLIP FOR 1/4 OD8 4 802-257C HFSS 1/4-20X3/4 GR59 1 805-009C PIN CLEVIS 5/16 X 2 1/210 1 805-010C PIN HAIR COTTER .09411 3 800-060C CABLE TIE .19X14.25 3DIA 50LB . . . . . . (Included for securing harness assembly)12 1 817-618C CAPLUG, CCF-7/8-14-20 BLACK13 2 890-921C STRAP, RATCHETING TIE DOWN

Available Replacement Parts for Part No. 840-246C Fertilizer/Seed Spreader Refer to Figure 8 on page 23:14 1 805-363C PIN COTTER 1/8 X 115 1 817-690C SPIN PLATE, SPIN SPREADER16 1 833-411C MOTOR ELECTRIC, SPIN SPREADER17 1 833-412C HARNESS ASSY, SPIN SPREADER18 1 MFHP81631 ELECTRONIC FEED GATE19 & 20 1 817-707C HOPPER & LID, SPREADER

Other Parts Not Listed Above Refer to Figure 8 on page 23:21 1 357-722D SPACER 3/4OD X 11GA WL X 3/4L22 2 842-406C HHCS 5/16-18X3 GR5 FTHD23 1 802-172C HHCS 5/16-18X2 1/2 GR524 1 803-020C NUT HEX 1/2-13 PLT25 3 803-084C NUT HEX NYLOCK 5/16-18 PLT26 1 803-147C NUT HEX NYLOCK 1/2-13 27 2 803-269C NUT HEX 10-32 PLT 28 2 804-046C WASHER FLAT #10 SAE PLT 29 1 N/A LH_STRAP 30 1 N/A RH_STRAP31 1 N/A BACK PLATE, SPREADER 32 1 N/A TUBE CAP LARGE 33 1 N/A EYE-BOLT 1/2-13 PLT 34 1 N/A FRAME, SPREADER . . . . . . . . . . . . . . . . . . (Included in Parts Bag "A" on page 25)35 1 N/A NUT HEX NYLOCK 8-32 . . . . . . . . . . . . . . . (Included in Parts Bag "A" on page 25)36 2 N/A SCREW 8-32X2 PHILLIPS 37 1 N/A FORMED WASHER

Item Qty. Part No. Part Description

23

Section 7: Appendix


Table of Contents

Figure 8

25786


Figure 9


Refer to Figure 9:18 1 322-100D EXTENSION TUBE, SPI19 1 805-035C PIN BENT 1/2 X 3 W/HA

Item Qty. Part No. Part Description

Figure 10

Extension Tube & Bent Pin for 2" Receiver Hitch

N SPREADERIRPIN 12B

Part No. 322-264A Hitch Mount With Rear Hitch for Disc HarrowItem Qty. Part No. Part Description

n

Refer to Figure 10:20 1 322-262S HITCH MOUNT REAR W/HRDWR KIT . . . . . . . . . (Includes items 22, 23, 24, 25 & 26)21 1 322-153S HITCH PULL . . . . . . . . . . . . . . . . . . . . . . . (Includes items 27, 28, 29, 30, 31, 32 & 33)22 1 322-131H SPREADER MOUNT WLDMT REAR23 2 806-004C U-BOLT 3/8-16 X 2 X 2 3/424 2 806-114C U-BOLT 3/8-16 X 3 1/32 X 3 1/225 2 806-021C U-BOLT 3/8-16 X 3 1/32 X 426 12 803-209C NUT FLANGE LOCK 3/8-16 PLT27 1 322-148D HITCH REAR, DISC28 2 805-318C PIN CLEVIS 3/4 X 2 49/64 USBL29 2 805-089C PIN COTTER 5/32 X 1 1/2 LONG30 2 802-658C HFS 1/2-13 X 3 1/2 GR5/831 2 803-169C NUT HEX FLG. LOCK 1/2-13 PLT.32 1 322-187H HITCH WLDMT33 1 805-308C PIN HITCH 3/8X5 1/8USBL DETENT

Spin Spreader Hitch Options (Not Included With Part No. 322-264A)Refer to Figure 10:34 1 890-971C TOW HOOK (LOAD 10,000 LBS)35 1 890-975C 2" BALL HITCH 3500LB 3/4 THRD



Figure 11

Parts Not UsedRefer to Figure 11:

The parts illustrated in Figure 11 are not mentioned in this manual. Should you have need for these parts, please refer to Moultrie Assembly Instructions included in the shipping box.

A

NOTE: Items (#35 & #36) listed on pages 4 & 22 are removed from parts bag “A” in Figure 11 and are used for attaching back plate (#31) to hitch weldment (#32).


Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

www.landpride.com

electric spin spreader - land pride · electric spin spreader for utility vehicles with 2"...

Documents