ege manisa 70 cm bir carinaro 55 cm fabriano june...

EGE Manisa 70 cm

BIR Carinaro 55 cm

Fabriano June 2012

Presenter

Francesco Nieli

Manisa EGE key

Keys and Interfaces

Carnaro BIR key

Tiny Full interface(SQG_CL_??)

Tiny SD interface(SQG_CL_??)

New LED interface(SQG_CL_??)

Carinaro BI interface(SQG_CL_??)

Functions

2

SUPER COOL function:

Rapidly chills food placed in the fridge without exposing food already

stored to thermal excursion.

On activation of this function, the refrigerator starts a special procedurethat sends cold air to the fridge cavity, lowering the temperature to “+1°C”.

To do this, the appliance runs 3 special compressor ON cycles.

The function finishes automatically at the end of the third On cycle, after a

Time Out of 12 hours, or manually if the relevant key is pressed.

SUPER FREEZE function:

Freezes food rapidly, enabling longer storage.

The function will only terminate when the maximum 24 hours is reached;

freezer function is assured at the minimum temperature.

The Super Freeze 48 hours function and exit on reaching the temperature

have also been eliminated on Partial-Integrated and Static appliances.

N.B.: When the function is activated, the appliance runs an initial defrost

cycle if and only if at least 3 hours of Compressor ON have passed since

the last defrost.

Functions

3

Pressing the button once enables the ozone function, and the relative LED/icon will light up.

Pressing the key again while the Ozone function is on will turn off the icon on the display and stop

the function (it does not stop automatically). The OZONE function also switches off when the

appliance is turned off.

In the event of a fault or alarm, the ozone generator will continue to work as normal. The only way

it will switch off in these circumstances is when a Reset Alarm turns the appliance off.

The device is powered (not managed) by the PCB.

It runs cyclically in "4 minute ON" and "26 minute OFF" intervals.

Nominally, 10 mg/h of ozone is generated during continuous function, hence the quantity of ozone

produced in our appliances is 1.33 mg/h.

It will not be tested during the Autotest function.

It runs on a 220 V supply.

Ozone-generator:The device uses the corona discharge effect to generate

ozone.

The purpose of this function is to produce ozone to:

a) Remove odours.

b) Kill bacteria.

c) Conserve fresh food for longer, especially

fruit and vegetables.

4

ECOPLUS function

The ECOPLUS function is similar to the ECO cycle which sets temperatures of “+5°C” &

“-18°C” automatically, with the difference that ECOPLUS regulates Fridge and Freezer

temperatures across the entire regulation table.

5 seconds after regulation has been changed, the display switches off then switches back on

again when a key is pressed. The display remains off even when the door is opened.

The underlying rationale is the same hence after cold air has been requested in the fridge

cavity, before switching off the compressor, cold air is sent to the freezer cavity.

ECOPLUS DISPLAY

TINY ALL / BI CARINARO

ACTIVATIONPress and hold SF and FRZ "+" temperature keys at the same time for 6 secs with appliance ON.

DEACTIVATIONPress ON/OFF key.

All LEDs/DGTs light up for 2 secs.

ENTRY

ACTIVATIONPress and hold the SC and FRG "+" temperature keys at the same time for 6 secs with appliance ON.

DEACTIVATIONSwitch off using combination of OFF.

4 LEDs light up for 2 secs: SC, SF, first FRG regulation and final FRZ regulation

In the event of a power failure (for all User Interfaces)

5

APPLIANCE STATE Behavior during black out

First switch-on Programming/ON

Appliance OFF (switched off from key)

OFF

STANDBY Goes back to Programing/ON

FRG / FRZ TEMPERATURE

They switch back on with the settings from prior to black-out.

SUPERCOOL If it was set, it reactivates after black-out.

SUPERFREEZE If it was set, it reactivates after black-out.

HOLIDAY If it was set, it reactivates after black-out.

CLK If it was set, it reactivates after black-out.

OZONE If it was set, it reactivates after black-out.

ECOPLUS It reactivates. Creates backup if set accordingly.

6

User Interface

TINY FULL and Single Door

TINY FULL and Single Door User Interface Navigation

7

ON/OFF button:Press the On/Off button once to switch the

appliance on. On switching on, the

appliance makes a rising beep as

confirmation plus the entire User Interface

lights up for 2 seconds.

Press the On/Off key for 3 seconds to

switch off. A descending beep confirms the

appliance has switched off.


8

Stand By:If the User Interface is idle for 2 minutes,

the display and LED switch to light-

saving illumination.

Pressing any key will restore the User

Interface to normal brightness.

Opening/closing the door has no effect.

When the appliance has a FAULT or

ALARM, it will not go into STAND BY (or it

will wake up if in stand-by already).

9

Appliance On:When switched on for the first time, thefridge temperature is set to +5°C and

freezer to –18°C.

Each time it is switched on after that,

the most recent user settings are

retrieved.

When the appliance is switched on, the

Fridge and Freezer temperatures are

shown, along with any other options

set.


10

Fridge Temperature Buttons:The fridge temperature regulation range has7 levels: +2°C; +3°C; +4°C; +5°C; +6°C;

+7°C; +8°C.

The temperature value increases on

pressing the “+” key and decreases on

pressing the “-” key.

The selected temperature is shown on the

display along with the “+” sign.

The regulation has an end of scale value, i.e.

when the table minimum is reached, it will go

no further (the capacitive keypad will emit the

standard beep in response).


11

Freezer Temperature Button:The freezer temperature regulation range has9 levels: -18°C; -19°C; -20°C; -21°C;

-22°C; -23°C; -24°C; -25°C; -26°C.

The freezer temperature value increases on

pressing the “+” key and decreases on

pressing the “-” key. The user's selected

temperature is shown on the display beside

the “-” sign.

The regulation has an end of scale value, i.e.

when the table minimum is reached, it will go

no further (the capacitive keypad will emit the

standard beep in response).



12

SUPER COOL function:The Super Freeze and Super Cool functions

can be set at the same time.

Pressing the Super Cool button once enables

the function, and the relative LED/icon will

light up. The letters “SC” will appear on the

Fridge section digits.

The Super Cool function disables manually

when the relative key is pressed again, when

the appliance is switched off, or automatically

after three Compressor On cycles at atemperature of “+1°C” or 12 hours after

activation.

13

Super Freeze Function:The Super Freeze and Super Cool functions

can also be set at the same time.

Pressing the Super Freeze button once enables

the function, and the relative LED/icon will light

up. The letters “SF” will appear on the Freezer

section digits.

The Super Freeze function disables manually

when the relative key is pressed again, when

the appliance is switched off, or automatically

after 24 hours.


14

“Manisa”

NEW ENTRY LED

User Interface

“Manisa” Entry LED User Interface navigation

15

Stand By:The User Interface never goes into STAND BY when idle, although the user

interface LEDs switch off when the door is closed.

ON/OFF status:When OFF, pressing the 2 keys on the left at the same time once will switch the

appliance on.

When ON, pressing and holding the 2 keys from the left at the same time for 3

seconds will switch the appliance off.

16

Programming Status (Appliance On):When the appliance is On, the Fridge and Freezer temperatures and any other options

configured are shown.When switched on for the first time, the temperatures are set at “+4°C” & “-18°C”.

Each time it is switched on after that, the most recent user settings are retrieved.


17

Refrigerator Temperature Buttons:The fridge temperature regulation range has 4 levels printed on the front: +2°C;

+4°C; +6°C; +8°C.

The temperature value increases from left to right when the far right key is pressed.

Pressing and holding will make it repeat until it reaches the end of scale.

On reaching the full scale value (or fourth level), pressing the key again will take it

back to level 1.


18

Freezer Temperature Button:The freezer temperature regulation range has 4 levels printed on the front: -18°C;

-20°C; -22°C; -26°C.

The temperature value increases from left to right when the first key on the left is

pressed.

Pressing and holding will make it repeat until it reaches the end of scale.

On reaching the full scale value (or fourth level), pressing the key again will take

it back to level 1.


19

SUPER COOL key:The Super Freeze and Super Cool functions can also be set at the same time.

On pressing the Super Cool key to turn the function on, the relative LED will light up and the LED

for the fridge cavity temperature set by the user will switch off.

Pressing the Freezer Temperature key while the function is enabled will generate audio and visual

feedback to signal incompatibility (3 short, fast beeps and 3 fast blinks) only on the LED for the

user-configured temperature.

The function can be ended:Automatically, after three Compressor On cycles at a temperature of “+1°C” or 12 hours

(time out) after activation.

Manually, when the relative key is pressed rapidly or when the appliance is switched off.

The LED for the function switches off and the LED for the temperature set by the user before the

function was enabled switches on again.


20

Super Freeze Button:The Super Freeze and Super Cool functions can also be set at the same time.

The Super Freeze function enables when the relative key is pressed, and the associated LED will

light up. The LED for the freezer cavity temperature (user freezer regulation) switches off.

Pressing the Freezer Temperature key while the function is enabled will generate a beep and

visual feedback to indicate incompatibility (3 short, fast beeps and 3 fast blinks) only on the LED

for the user-configured temperature.

The Super Freeze function can be ended:Automatically, 24 hours after activation or when an Alarm or Fault occurs.

Manually, when the relative key is pressed again, or when the appliance is switched off.

The Super Freeze LED switches off and the LED for temperature set by the user before the

function was enabled switches on again.


___ ____ ___ __________ ___ _____ ___ _____ _____ ______

______ _______

____ _______

_____ _______

_____ _______

Click to modify the font displayed

Level II

Level III

Level IV

Level V

Freezer Fan Function - Appliances: EGE

Freezer Fan is always starting at 9 Volts;

When the On time of Compressor arrives at 180 min the Freezer Fan switches to 11Volts

If the cycle stops at 11 Volts, the Fan restarts the next cicle at 11 Volts;

If the cycle is lasting less then 3 hrs, the next cycle will be at 9 Volts;

* The Fan start at minimum 8 Volts only the cycle after defrost.

11V

Compressor

Off

FZ FAN

CPS ON ≥ 3

hours

CPS ON

≤ 3hrs

CPS ON

≤ 3hrs

When CPS ON

arrive at 3hours the

fan switch to 11VWhen the last CPS

ON is less then

3hours the fan

switch to 9V

9V

22

Internal air flow - Appliances: EGE

23


24


25


26

“Carinaro” Built In

User Interface

“Carinaro” Built In User Interface Navigation

27

ON/OFF status:When the appliance is connected to the mains power supply, the "plug" LED icon

lights up; it switches off when the appliance is unplugged.

The appliance switches on when the ON/OFF key is pressed. On switching on, a

rising beep sounds.

Once on, pressing and holding the On/Off key for at least 3 seconds will switch the

appliance off; a descending beep will sound.

Stand By:The User Interface never goes into STAND BY when idle, although the user

interface LEDs switch off when the door is closed.

28

Appliance ON:When the appliance is switched on, the set Fridge and Freezer temperatures are

shown (not the actual temperatures inside the cavities) and any other options

configured.When switched on for the first time, the following temperatures are set: “+5°C” and

“–18°C”.

Each time it is switched on after that, the most recent user settings are retrieved.


29

Fridge Temperature Button:The fridge temperature regulation range has 7 levels:

+2°C; +3°C; +4°C; +5°C; +6°C; +7°C; +8°C.

Temperature values increase when the “+” key is pressed and decrease when the

“-” is pressed, and are shown on the display along with the “+” sign.

The regulation has an end of scale value, i.e. when the table minimum or maximums

are reached, it is impossible to go any further.


30

Freezer Temperature Button:The freezer temperature regulation range has 9 levels: -18°C; -19°C; -20°C; -21°C; -22°C; -23°C; -24°C; -25°C; -26°C.

Temperature values increase when the “+” key is pressed and decrease when the “-”

is pressed, and are shown on the freezer display along with the “-” sign.

The regulation has an end of scale value, i.e. when the table minimum or maximums

are reached, it is impossible to go any further.


31

SUPER COOL function:The Super Freeze and Super Cool functions can also be set at the same time.

Pressing the Super Cool button once enables the function, and the relative LED/icon will light up. The target fridge temperature remains on the DIGITS (+1°C).

The Super Cool function disables manually when the relative key is pressed again,

when the appliance is switched off, automatically after three Compressor On cycles ata temperature of “+1°C”,12 hours (time out) after activation, or in the event of a fault

or temperature alarm (A1 or A2).


32

Super Freeze Function:The Super Freeze and Super Cool functions can also be set at the same time. The

target freezer temperature to be reached remains on the DIGITS.

The Super Freeze function disables manually when the relative key is pressed, when

the appliance is OFF or automatically at the end of the set time.


33

Holiday Function:Pressing the relative key activates the Holiday function. On activation, a beep sounds

and the relative icon lights up on the display.Temperatures in each of the cavities are changed to “+12°C” for the fridge and

“-18°C” for the freezer.

The function can only be disabled manually by pressing the relative key again. It will

also disable when there is a temperature alarm or in the event of a fault.


34

Ozone-generator:This function cannot be activated from the User Interface.

In the fridge cavity of the appliance (at the top) there is a button to switch the function

on and off.

This appliance follows the same operating logic as explained earlier in this

presentation.


___ ____ ___ __________ ___ _____ ___ _____ _____ ______

______ _______

____ _______

_____ _______

_____ _______


Level II

Level III

Level IV

Level V

Freezer Fan Function - Appliances: BIR

Fz fan is always starting at 9 Volts;

If the ON Compressor is lower than 180 min, the fan works at 9 Volts;

When the Compressor time reaches 180 min, the fan switchs to 11 Volts;

If the cycle stops at 11 Volts, the Fan restarts the next cicle at 11 Volts;

If the cycle is lasting less then 3 hours, the next cycle will be at 9 Volts;

• The Fan starts at minimum 8 Volts only the cycle after defrost.

11V

Compressor

Off

FZ FAN

CPS ON ≥ 3

hours

CPS ON

≤ 3hrs

CPS ON

≤ 3hrs

When CPS ON

arrive at 3hours the

fan switch to 11VWhen the last CPS

ON is less then

3hours the fan

switch to 9V

9V

36

Internal air flow - Appliances: BIR

Fridge cavity

Freezer cavity Freezer cavity

Defrosting

Starting Forced Defrost (For Service)

38

How to start forced defrost:A forced defrost procedure has been introduced in all appliances in the ARTICA

Platform and also in these appliances; it should be used when the Evaporator

Battery needs to be defrosted and a three-hour Compressor ON hasn’t been

completed yet.

The procedure consists of the following steps:• Starting with the appliance On and the door closed, open and close the fridge

door four times consecutively. Do not leave more than 5 seconds between one

action (open / close) and the next.

• Within five seconds, open the fridge door for a fifth time.

• Keeping the fridge door open, within 5 seconds switch the appliance off (using

the On/Off button or knob, depending on the type of interface).

• Keeping the fridge door open, within 5 seconds switch the appliance back on

(using the On/Off button or knob, depending on the type of interface).

The procedure will be canceled in the following cases:• If more than 5 seconds is left between one step and the next.

• If the appliance is switched off in steps 1 and 2.

• If the fridge door is closed in steps 3 and 4.

___ ____ ___ __________ ___ _____ ___ _____ _____ ______

______ _______

____ _______

_____ _______

_____ _______


Level II

Level III

Level IV

Level V

Defrost Procedure in EGE NF appliances

Start of the defrost cycle depends from:• Duration of last defrost.

• Time of fridge door opening (every 5 cumulative minutes of door open time

reduces the start of the next defrost cycle by one hour)

• Compressor ON time (minimum is 10 hours)

• Actual time between 2 defrost cycles could be in the range [minimum 10 hours

/ maximum 30 hours (48 hours only if the product is in Energy Consumption

Test)]. (Consumption Test conditions: ECO Mode + Door Closed for at

least 14 hours + Last Compressor ON less than 3 hours ago.)

Defrost cycles can be activated by some particular circumstances:• In the event of Alarms “A1” and “A2”, a defrost cycle is carried out every 2 hours.

• If the Door Open Alarm remains active for more than 30 minutes, a defrost cycle

will be performed every 2 hours until the door is closed (Alarm Reset).

• In the event of activation of the Super Freeze Function, if at least 3 cumulative

hours of Compressor ON have passed since the last defrost cycle.• If the Fridge Air Probe registers a value above +12°C for 135 consecutive minutes

(this function is not available when the Holiday Function is active).

___ ____ ___ __________ ___ _____ ___ _____ _____ ______

______ _______

____ _______

_____ _______

_____ _______


Level II

Level III

Level IV

Level V

Defrost Procedure in EGE NF appliances

Description:• (A) - All loads are disabled and the defrost heating elements are switched on.• (B) - The heating elements switch off when the freezer evaporator probe reaches +17°C or after 50 minutes

(Defrost Time Out).

• (C) - As soon as the heating elements switch off, the freezer fan is activated for 5 seconds in order to deliver

warm air to the cold air inlet pipe from the freezer compartment into the fridge compartment. Everything else

remains switched off during this time.

• (D) - All the loads remain disabled for around 12 minutes to allow the water to flow into the compressor drawer.

• (E1 energy consumption test) - The compressor is switched on to cool the coil that has heated up duringdefrosting for a fixed time of 10min, the FZ fan started only when the freezer evaporator probe reaches +0°.

• (E2 out of energy consumption test) - The compressor is switched on to cool the coil that has heated upduring defrosting for a fixed time of 10min or when the freezer evaporator probe reaches 0°C, then also the FZ

fan is switched on for 1min; after this 1minute, the fan is switched off and compressor works until the evaporatorprobe reaches -25°C or fixed time 15min.

ON

OFF(A)

(B)

(C) (E1)

(D)

Heating elementsFreezer fan Damper

Compressor

(E2)

___ ____ ___ __________ ___ _____ ___ _____ _____ ______

______ _______

____ _______

_____ _______

_____ _______


Level II

Level III

Level IV

Level V

Defrost Procedure in Carinaro BIR PNF appliances

Start of the defrost cycle depends from:• Duration of last defrost.

• Time of fridge door opening (every 5cumulative minutes of door open time reduces

the start of the next defrost cycle by one hour)

• Compressor ON time (minimum is 9 hours)

• Actual time between 2 defrost cycles could be in the range [minimum 10 hours /

maximum 30 hours (48hours only if the product is in EC Mode)] > (Consumption

Test conditions: ECO Mode + Door Closed for at least 14 hours + last

Compressor ON at least 3 hours ago)

Defrost cycles can be activated by some particular circumstances• In the event of Alarms “A1” and “A2”, a defrost cycle is carried out every 2 hours.

• If the Door Open Alarm remains active for more than 30 minutes, a defrost cycle will be

performed every 2 hours until the door is closed (Alarm Reset).

• In the event of activation of the Super Freeze Function, if at least 3 cumulative hours

of Compressor ON have passed since the last defrost cycle.

___ ____ ___ __________ ___ _____ ___ _____ _____ ______

______ _______

____ _______

_____ _______

_____ _______


Level II

Level III

Level IV

Level V

Defrost Procedure in Carinaro BIR PNF appliances

Description• (A) - All loads are disabled and the defrost heating elements are switched on.• (B) - The heating elements switch off when the freezer evaporator probe reaches +17°C or after

50 minutes (Defrost Time Out). When the product is in Power Consumption, the treshold of thethe freezer evaporator probe to exit by this step is +1°C.

• (C) - As soon as the heating elements switch off, the freezer fan is activated for 5 seconds in order to

deliver warm air to the cold air inlet pipe from the freezer compartment into the fridge compartment.

Everything else remains switched off during this time.

• (D) - All the loads remain disabled for around 12 minutes to allow the water to flow into the

compressor drawer.

• (E) - The compressor is switched on to cool the coil that has heated up during defrosting until theFreeze Evaporator probe reaches -5°C, than for fixed time of 15min the Freeze Fan is switched ON

with compressor.

ON

OFF(A)

(B)

(C) (E)

(D)

Heating elementsFreezer fan

Compressor

Description of Alarms (in all User Interfaces)

44

Door Open ALARMIf the fridge door is left open for longer than 2 minutes, the Door Open Alarm

will activate, a buzzer will sound and the fridge lamp will no longer remain

permanently alight but begin flashing on and off at regular intervals.

Description of Alarms (in all User Interfaces)

45

“A1” & “A2” FREEZER TEMPERATURE ALARM:There are two types of alarm as on current models: A1 (minor) and A2 (critical). Each alarm has

a display message and constant beep.

Temperature alarms are disabled for the first 24 hours of appliance operation (only the first ever 24

hours, not every time it is switched on).

To silence the beep, open and close the FRIDGE door or press the change Freezer Temperature

keys (for all UIs).

To set the alarm, switch the appliance off or press the change Freezer Temperature buttons twice

(for all UIs). The buzzer doesn't have to be silenced and reset at the same time. One can happen

some time after the other.

Super Cool and/or Super Freeze options are disable during a temperature alarm, and nothing will

happen when the relative keys are pressed. When the alarm situation has been rectified, the

target temperature set by the user will be shown again.

The Carinaro Tiny and Built In User Interfaces show the alarm, and in New Entry models the LEDs

also blink when the door is closed.

N.B.: In the event of a power failure when an alarm has occurred, if it was a temperature alarm it

will be presented immediately when the time is reset with the door open (meaning it will be shown

again after 2 minutes).

Alarme “A2”Alarme “A1”

Electronic

Troubleshooting

Autotest activation

47

The autotest function starts with the appliance off.

If there is a Last Fault in the memory, the appliance shows it immediately for 20 seconds,

after which the Autotest sequence commences.

The Last Fault only cancels at the end of the Autotest sequence. If the autotest is

interrupted, the Last Fault is presented again when the procedure is restarted.

On completion of the autotest, a long beep sounds and the appliance turns OFF again. The

Last Fault transfers to rolling visible memory only via the Cooling Doctor diagnostic tool.

AUTOTEST ACTIVATION DISPLAY

TINY ALL / BI CARINARO

ACTIVATION

Long press of the Super Freeze key for 6 seconds (or Super Cool on single door fridges).

- All LEDs light up for 2 seconds.- The Last Fault is shown (where present)

for 20 seconds.- All LEDs light up for remaining duration of

the autotest.

NEW ENTRY

ACTIVATION

Long press of Super Freeze key for 6 seconds.

- The 4 LEDs used to signal Faults light up for 2 seconds: Super Freeze, “-18” and “+8“ and the Super Cool LED.

- The Last Fault is shown (where present) for 20 seconds.

Autotest Sequence [No Frost Fridge-Freezer, EGE]

Step Duration Action Light Notes

1 5 seconds Pause OFF

2 1 second Probe check OFF

If there are no probe faults,it skips to step 3.

If there are probe faults,it skips to step 6.


4 125 seconds

FZ fan ON

DeFrost heating element ON

Damper open

OFF

5 120 secondsFZ fan ON

DeFrost heating element ONDamper closed

OFF Skips to step 8


DeFrost heating element ONDamper open

Blinking


DeFrost heating element ONDamper closed

Blinking

8 Autotest ends

Autotest Sequence [No Frost 4-door, EGE]

Step Duration Action Light Notes



If there are no probe faults,it skips to step 3.

If there are probe faults,it skips to step 6.


4 125 seconds

FZ fan ONDeFrost heating elementON

Tab heating element ONDamper open

OFF

5 120 seconds

FZ fan ONDeFrost heating element ON

Tab heating element ONDamper closed

OFF Skips to step 8

6 125 seconds


Tab heating element ONDamper open

Blinking

7 120 seconds


Tab heating element ONDamper closed

Blinking

8 Autotest ends

Autotest Sequence [Partial No Frost Fridge-Freezer, BIR]

Step Duration Action FG light Note



If the probe control is OK, it skips to step 3.

If there are probe faults (KO), it skips to step 5.


4 245 seconds

FZ fan ONFG fan ON


ON After this test, it skips to step 6.

5 245 seconds

FZ fan ONFG fan ON


Blinking

6 End of Autotest.

Autotest Sequence [Static Fridge-Freezer, BIR]

Step Duration Action FG light Note



If the probe control is OK, it skips to step 3.

If there are probe faults (KO), it skips to step 5.


4 245 seconds FG fan ON ON After this test, it skips to step 6.

5 245 seconds FG fan ON Blinking

6 End of Autotest.

Description of Faults (Manisa New Entry)

FAULTIndication

LED 1 LED 2 LED 3

F01

F02

F04

F05

F07

F08

F09

F10

F13

F15

F16

F22

F23

F24

F25

F26

F27

KEY

On

Off

Blinking

The LED signaled by the red arrow blinks

rapidly for the entire duration of the FAULT.

See Artica Table SQG_CL_31 for the relative

Fault Table.

F

52

53

F

Fault Display

TINY User Interface:The FAULT is indicated by an “F” on the

upper digits and the fault number in “XX”

format on the lower digits.

In Single Door models

(just fridge or just freezer): The letter “F” alternates with the fault

number on the display every 2 seconds.

Fault Display

54

1 2 3

NEW ENTRY User Interface:During a FAULT, the LED below the red arrow blinks rapidly, the only meaning of

which is that there is a FAULT in the appliance.

The LED with the green arrow indicates the FAULT number.

CARINARO Built In User Interface:The FAULT is indicated by an “F” on the left-hand side digit and the fault number in

“XX” format on the right.

55

Components - VERY IMPORTANT:Electronic Appliances:In these appliances, the damper and the multiflow

polystyrene are managed with a single KIT, NOT TO BE

DISMANTLED in order to avoid any leakage of air

remaining after reassembly, which could impair appliance

function.

Components

56

Disassembly

EGE 70 cm & 4 Door

57

Disassembly

Removal of Tiny Control Panel:1. Use a slim screwdriver to remove the outer

plastic panel, being careful not to scratch the

door (we recommend using some plastic tape to

protect the door).

2. Take out the fixing screws.

3. Use a slim screwdriver to remove the Display

PCB, being careful not to scratch the door (we

recommend using some plastic tape to protect

the door).

4. Disconnect the PCB connector.

N.B.: In step 3, be careful not to break the

Display PCB (when you are removing it for a

check and not to replace it).

1

2

3

4

58

Disassembly

1

2

3

4

Replacing the Light

(dismantling light holder):1. Use a slim screwdriver to lift up the

outer cover over the light holder

screws.

2. Remove the outer cover.

3. Using a slim screwdriver to remove

the 2 screws securing the light

holder.

This will give you direct access to the

light and light holder connector, if it

needs to be replaced.

59

Disassembly of Classic Ege 70 cm and 4-Door models

Disassembly of Fridge Multiflow1. Remove the drawers and shelves from the

fridge cavity.

2. Remove the 2 screws securing the Divider in

the Fridge Cavity.

3. Pull on the Divider to take it out of the Fridge

Cavity.

4. Remove the 5 plugs covering the screws.

5. Remove the 5 screws fixing the multiflow

6. Move the multiflow forward slightly and

disconnect the damper connector.

7. Pull the multiflow right out.

8. Separate the polystyrene from the plastic

cover, taking great care not to break it

N.B.: The damper must be replaced together

with the polystyrene so that during

reassembly no surfaces are left

inadequately sealed, allowing leakage

of air and potentially impairing the

performance of the fridge cavity.

1

2

3

60

Disassembly of Classic Ege 70 cm and 4-Door models

Disassembly of Fridge Multiflow1. Remove the drawers and shelves from the

fridge cavity.

2. Remove the 2 screws securing the Divider in

the Fridge Cavity.

3. Pull on the Divider to take it out of the Fridge

Cavity.

4. Remove the 5 plugs covering the screws.

5. Remove the 5 screws fixing the multiflow

6. Move the multiflow forward slightly and

disconnect the damper connector.

7. Pull the multiflow right out.

8. Separate the polystyrene from the plastic

cover, taking great care not to break it

N.B.: The damper must be replaced together

with the polystyrene so that during

reassembly no surfaces are left

inadequately sealed, allowing leakage of

air and potentially impairing the

performance of the fridge cavity.

4

5

6

8

61

Disassembly of Freezer Multiflow:1. Remove the freezer cavity drawers

2. Remove the 6 screws fixing the multiflow.

3. Pull gently on the bottom of the multiflow to

remove it.

4. Open the connectors cover by pressing on the

fixing clips.

5. Pull the connectors out.

The whole Freezer Multiflow assembly can now

be removed.

Disassembly of Classic Ege 70 cm

1

2 3 4

5

62

Disassembly of freezer multiflow:1. Take out the drawers from the top and bottom

of the Freezer Cavity (the disassembly

procedure is similar to the latest 4-door

appliances).

2. Remove the 6 screws fixing the multiflow.

3. Pull gently on the bottom of the multiflow to

remove it.

4. Open the connectors cover by pressing on the

fixing clips.

5. Pull the connectors out.

The whole Freezer Multiflow assembly can

now be removed.

Disassembly of 4-Door Ege 70 cm models

1

3

4

5

2

63

Disassembly of freezer evaporator:1. Remove the 4 screws securing the polystyrene to the

backplate.

2. Being careful not to split the polystyrene, take it off the

backplate.

3. Remove the adhesive tape over the top part of the polystyrene.

4. Open the cover to obtain access to the fan.

N.B.: The fan and the white frame are handled as a single

replacement unit. THEY DO NOT NEED TO BE

DISMANTLED!!!

1

Disassembly/Opening EGE 70 & 4D Freezer Multiflow

3

4

64

Disassembly

Carinaro Built In

65

Removing the Fan1. Remove the 2 plugs covering

the screws.

2. Remove the 2 screws securing

the fan.

3. Unplug the fan from its power

supply.

1

Disassembly of CARINARO Built In Appliances:

3

2

66


Disassembly of

Ozone Generator:1. Remove the 2 screws securing

the ozone generator.

2. Unplug the ozone generator

from its power supply.

12

Important:Don't forget that the ozone

generator is a single unit and must

be replaced as a whole.

67

1


Disassembly of Freezer Cavity:1. Remove the lower drawer.

2. Unscrew the 4 screws securing the door to

the upper compartment of the freezer

cavity.

3. Take off the door and the grille.

4. Unscrew the 3 screws on the front panel of

the freezer cavity.

5. Unscrew the remaining 2 screws securing

the evaporator cover.

6. Open the evaporator area.

7. Disconnect the fan/heating element

connector.

N.B.: All components will now be accessible.

2

68

3


4


2. Unscrew the 4 screws securing the door

to the upper compartment of the freezer

cavity.


4. Unscrew the 3 screws on the front panel

of the freezer cavity.





connector.


5

69



2. Unscrew the 4 screws securing the door

to the upper compartment of the freezer

cavity.


4. Unscrew the 3 screws on the front panel

of the freezer cavity.





connector.


7

ege manisa 70 cm bir carinaro 55 cm fabriano june...

Documents