economical series tool resetting devices · ezop - 50 hp - 50b 53 Ø 68 125 springy probes (c325);...
TRANSCRIPT
142Page
Magnetic Base Tool Resetting
Luminous WarningOptical Type Height
Alignment
Fixed Magnetic
Base
ClockHeight AlignmentHP - 100
* Place the height alignment on the proper reference surface of the work pieces. * Lower the cutting tool in Z (Upward/Downward) Axis. Then, the cutting tool will come to the measurement position.* Thus, the distance between the reference surface of the piece and cutting tool will be measured sensitively and easily.* The height alignment can be used at many machines, it is used in conventional lathes and mills. * The height alignment is used vertically and horizontally.
* Sensitivity 0.005 mm* Height 50 mm Fixed Magnetic Base* When the tool is contacted, the red light is on. * Vertical and horizontal alignment with one tool
Order Reference Weight
14990 HP - 100 Heigth from surface100 mm 2.6 kg.
Order h Product Model kg
14993 50mm
HP - 50Z Standard Type 0.7kg14994 HP - 50ZM Magnetic Base
Order h Product Model kg
14991 50 mm
HP - 50A Vertical Reading 1.1 kg14992 HP - 50B Horizontal Reading 1.7 kg
Order h Product Model WeightEZOP50 50 Luminous Reading 0.5 kgEZDI100 50 Time Reading 1.9 kg
Order Product Model
13697 C325 Mechanical Probe - 10 /4 mm
13698 C324-A Luminous Probe - 20 x 160 mm
13699 C324 Luminous-Audible Probe 20 x 160 mm
13700 Small Diameter Luminous-Audible 6 x120 mm
Order Product Model
13691 50 mm 'Z' Contrary
Resetting Device with Clock
Ø 49.5
Ø 40
Ø 50
50
Ø 54
Ø 18
Magnetic BaseTool Resetting
Tool Resetting
Clock Type
Tool ResettingLuminous
Warning ‘Z’
Economical Series PROBES
Economical SeriesTool Resetting Devices
Economical Series PROBES
'Z' Contrary Tool Resetting
Tool Resetting Clock TypeUsage Areas;For Tool settingsIt is for adjusting to zero “0” and to determine the machine shaft to the reference point.Advantages; During smearing, the tool cutting edge is not damaged. There is no need for thickness gauge and drive shaft.Usage Method; Please bring the springy contact surface and measurement surface to the same height and adjust the measuring clock indicator as '-0.50'. 2. Place the resetting tool on the bench. Keep the milling tool end of the cutting tool at springy contact surface of the device until reaching '0', with this setting 50 mm adjusted position is shown for the work piece to be processed.
HP50ZM
HP50Z HP - 50A
EZOP - 50
HP - 50B
53 Ø 68
125
Springy Probes (C325); In operation, the mandrel turns with flexure – the mandrel contacts the work piece and works without flexure – The mandrel moves to the side suddenly = reference point is determined.Light Indicator Side Resetting End (C324 );In case the detention ball and metal work piece are contacted, the battery switches on the lamps. Thus, the reference point – the hole centers are determined.
ø 65 mm
ø 13.5
50
mm
1. Bring the test button on side surface from “use” position to the “test “position.2. When the grinded surface is pressed downwards, the small pointer will show zero. By holding in this position, reset it according to the big pointer. 3. K When starting the application, bring the “Test” position to the “Use” position. 4. Place the device on the machine table, bring the magnetic base to “On” position. The distance that cutting tool pressure brings the small and big pointer to the “0” position is 100 mm.
Height; 101.5 mm(At Open Position)
Indicator time;0.01 intermittent
needle turns to "0" (Zero)” directly.Magnetic base, 80 kg capacity
1 2
100 m
m 100 m
m
100 m
m
34
C325
C324
Order Product Model
13692 100 mm Magnetic Base Resetting
Device with Clock
Order Product Model
13693
50 mm Magnetic Base
Luminous Resetting Device.
Sensitivity0.01 mm
Sensitivity0.01 mm
Sensitivity0.01 mm
CU
TT
ING
TO
OL
RE
SE
T D
EV
ICE
S
Sensitivity0.01 mm
Usage; 1. It is to determine the axial reference points of the mill pinol without damaging the work piece. 2. In case of contact, the warning light is turned on. 3.Thanks to the springy bedding contact surface, allows the approach to the work piece with 0.002 sensitivity. 4. Thanks to the magnetic base, it provides vertical - horizontal using opportunity.