ece 4371, fall, 2013 introduction to telecommunication engineering/telecommunication laboratory
DESCRIPTION
ECE 4371, Fall, 2013 Introduction to Telecommunication Engineering/Telecommunication Laboratory. Zhu Han Department of Electrical and Computer Engineering Class 9 Sep. 25 th , 2013. Outline. Review of quantization 6dB rule Two optimal rules PCM, DPCM, ADPCM Delta modulation - PowerPoint PPT PresentationTRANSCRIPT
ECE 4371, Fall, 2015
Introduction to Telecommunication Engineering/Telecommunication Laboratory
Zhu Han
Department of Electrical and Computer Engineering
Class 9
Sep. 22nd, 2015
OutlineOutline Review of quantization
– 6dB rule– Two optimal rules
PCM, DPCM, ADPCM Delta modulation Error in PCM T carrier system (cable and fiber communication)
Pulse Code Modulation (PCM)Pulse Code Modulation (PCM)
Pulse code modulation (PCM) is produced by analog-to-digital conversion process. Quantized PAM
As in the case of other pulse modulation techniques, the rate at which samples are taken and encoded must conform to the Nyquist sampling rate.
The sampling rate must be greater than, twice the highest frequency in the analog signal,
fs > 2fA(max) Telegraph time-division multiplex (TDM) was conveyed as early as 1853, by
the American inventor M.B. Farmer. The electrical engineer W.M. Miner, in 1903.
PCM was invented by the British engineer Alec Reeves in 1937 in France. It was not until about the middle of 1943 that the Bell Labs people became
aware of the use of PCM binary coding as already proposed by Alec Reeves.
Figure Figure The basic elements of a PCM system.The basic elements of a PCM system.
Pulse Code Modulation
Advantages of PCM
1. Robustness to noise and interference
2. Efficient regeneration
3. Efficient SNR and bandwidth trade-off
4. Uniform format
5. Ease add and drop
6. Secure DS0: a basic digital signaling rate of 64 kbit/s. To carry a typical phone call, the audio sound is digitized at an 8 kHz sample rate using 8-bit pulse-code modulation. 4K baseband, 8*6+1.8 dB
Virtues, Limitations and Modifications of PCM
Encode information in terms of signal transition; a transition is used to designate Symbol 0
Regeneration (reamplification, retiming, reshaping )
3dB performance loss, easier decoder
Differential Encoding
1 1
Consider a finite-duration impulse response (FIR)
discrete-time filter which consists of three blocks :
1. Set of p ( p: prediction order) unit-delay elements (z-1)
2. Set of multipliers with coefficients w1,w2,…wp
3. Set of adders ( )
Linear Prediction Coding (LPC)
Block diagram illustrating the linear adaptive prediction process.
Reduce the sampling rate
Differential Pulse-Code Modulation (DPCM)
Usually PCM has the sampling rate higher than the Nyquist rate.The encode signal contains redundant information. DPCM can efficiently remove this redundancy. 32 Kbps for PCM Quality
) (minimize G maximize filter to prediction aDesign
G Gain, Processing
)SNR(
is ratio noiseon quantizati-to-signal theanderror sprediction theof variance theis where
)SNR(
))(((SNR)
and 0)]][[( of variancesare and where
(SNR)
is system DPCM theof (SNR) The
2
2
2
2
2
2
2
2
2
2
o
22
2
2
o
o
Ep
E
Mp
Q
EQ
E
Qp
Q
E
E
M
QM
Q
M
G
nqnmEnm
Processing Gain
Need for coding speech at low bit rates , we have two aims in mind:
1. Remove redundancies from the speech signal as far as possible.
2. Assign the available bits in a perceptually efficient manner.
Adaptive quantization with backward estimation (AQB).
Adaptive Differential Pulse-Code Modulation (ADPCM)
ADPCM
Adaptive prediction with backward estimation (APB).
8-16 kbps with the same quality of PCM
Coded Excited Linear Prediction (CELP)Coded Excited Linear Prediction (CELP) Currently the most widely used speech coding algorithm Code books Vector Quantization <8kbps Compared to CD
44.1 k sampling
16 bits quantization
705.6 kbps
100 times difference
Delta Modulation (DM)
size step theis and , of version quantized the
is ,output quantizer theis where
1
) sgn(
1 is signalerror The
).( of sample a is )( and period sampling theis where,2,1,0 , )(Let
ne
nenm
nenmnm
nene
nmnmne
tmnTmTnnTmnm
qqq
q
q
ss
s
The modulator consists of a comparator, a quantizer, and an accumulator. The output of the accumulator is
)sgn(
1
1
n
iq
n
iq
ie
ienm
Slope overload distortion and granular noise
.)( of slope local the torelative large toois size step when occurs noisegranular hand,other On the
)(max (slope)
require we, distortion overload-slope avoid Tosignalinput theof difference backward
first a isinput quantizer the,1for Except 11
have We
, by error on quantizati theDenote
tm
dttdm
T
nqnqnmnmne
nqnmnmnq
s
q
Slope Overload Distortion and Granular Noise
( differentiator )
The modulation which has an integrator can
relieve the draw back of delta modulation (differentiator)
Beneficial effects of using integrator:
1. Pre-emphasize the low-frequency content
2. Increase correlation between adjacent samples
(reduce the variance of the error signal at the quantizer input )
3. Simplify receiver design
Because the transmitter has an integrator , the receiver
consists simply of a low-pass filter.
(The differentiator in the conventional DM receiver is cancelled by the integrator )
Delta-Sigma modulation (sigma-delta modulation)
Two Types of ErrorsTwo Types of Errors Round off error Detection error Variance of sum of the independent random variables is equal to
the sum of the variances of the independent random variables. The final error energy is equal to the sum of error energy for
two types of errors Round off error in PCM
22
31
Lmp
q
Mean Square Error in PCMMean Square Error in PCM If transmit 1101 (13), but receive 0101 (5), error is 8 Error in different location produces different MSE
Overall error probability
– Gray coding: if one bit occur, the error is minimized.
)2)(2( pi
i m
)2(3)12(4
)( 2
22
1
2
1
2n
nep
n
iieie
n
ii
PmPPMSE
Bit Errors in PCM Systems
Simplest case is Additive White Gaussian Noise for baseband PCM scheme -- see the analysis for this case. For signal levels of +A and -A we get
pe = Q(A/)
Notes
•Q(A/) represents the area under one tail of the normal pdf
•(A/)2 represents the Signal to Noise (SNR) ratio
• Our analysis has neglected the effects of transmit and receive filters - it can be shown that the same results apply when filters with the correct response are used.
Q Function For Q function:
– The remain of cdf of Gaussian distribution
– Physical meaning– Equation
Matlab: erfc– y = Q(x) – y = 0.5*erfc(x/sqrt(2));
Note how rapidly Q(x) decreases as x increases - this leads to the threshold characteristic of digital communication systems
0 1 2 3 4 5 610
-10
10-8
10-6
10-4
10-2
100
Q Function
QPe
SNR vs. SNR vs.
Threshold Saturation
– slightly better than ADC Exchange of SNR for bandwidth is much more efficient
than in angle modulation Repeaters
2
2
02
2
0
0
)/()12(41
)2(3
pn
n
mm
nQNS
Time-Division MultiplexingTime-Division Multiplexing
Figure Block diagram of TDM system.
DS1/T1/E1DS1/T1/E1 Digital signal 1 (DS1, also known as T1) is a T-carrier signaling
scheme devised by Bell Labs. DS1 is a widely used standard in telecommunications in North America and Japan to transmit voice and data between devices. E1 is used in place of T1 outside of North America and Japan. Technically, DS1 is the transmission protocol used over a physical T1 line; however, the terms "DS1" and "T1" are often used interchangeably.
A DS1 circuit is made up of twenty-four DS0 DS1: (8 bits/channel * 24 channels/frame + 1 framing bit) * 8000
frames/s = 1.544 Mbit/s A E1 is made up of 32 DS0 The line data rate is 2.048 Mbit/s which is split into 32 time slots,
each being allocated 8 bits in turn. Thus each time slot sends and receives an 8-bit sample 8000 times per second (8 x 8000 x 32 = 2,048,000). 2.048Mbit/s
Synchronization Synchronization Super Frame
Synchronization Synchronization Extended Super Frame
T Carrier SystemT Carrier SystemTwisted Wire to Cable System
Fiber CommunicationFiber Communication