ece 325 electric energy system components 8-...
TRANSCRIPT
![Page 1: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/1.jpg)
1
Instructor:
Kai Sun
Fall 2015
ECE 325 – Electric Energy System Components8- Fundamental Elements of Power Electronics
![Page 2: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/2.jpg)
2
Content
(Materials are from Chapter 21)
• Power semiconductor switches
– Diodes, thyristors, etc.
• DC-to-DC switching converters
• DC-to-AC switching converters
![Page 3: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/3.jpg)
3
Introduction
• A power electronics system is to process and control the flow of
electric energy by supplying voltages and currents in a form that
optimally suits the loads
• A typical power electronics (PE) system:
Power Electronics
Converter
Load
Controller
Power input
vi, ii
Power output
vo, io
Control signals Measurements
Reference
![Page 4: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/4.jpg)
4
Applications of PE converters
• For DC voltage or current, a PE converter can regulate the magnitude at a
desired level or adjust the magnitude to a desired level
• For AC voltage or current, a PE converter can adjust the magnitude and
frequency and change the number of phases
• Applications:
– Switched-mode (DC) power supplies
– Uninterrupted power supplies (UPS)
– Adjustable speed motor drives
– High-voltage DC transmission (HVDC)
– Battery-based utility energy storage
– Electric vehicles (EVs) and hybrid electric vehicles (HEVs)
– Renewable energy integration, e.g. solar PV and wind generation
![Page 5: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/5.jpg)
5
Classification of PE converters
Four types of PE converters Examples of application
DC-to-DC (boost up/step down): Power supplies for electronic devices
DC-to-AC (inverter, to 1-phase
or 3-phase AC)
The battery (discharging) and solar PV
interfaces to the power grid
AC-to-DC (rectifier) The battery (charging) interface to the power
grid and power adapters for electronic devices
AC-to-AC Variable-speed motor drive
• Two examples of AC-to-AC convertors:
![Page 6: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/6.jpg)
6
Power semiconductor switches
• Power semiconductor switches are the key functional
components in a PE converter; other components are such as
resistors, inductors and capacitors.
• Two states: ON (conducting) and OFF (open-circuit)
• Three types of power semiconductor devices in terms of the
controllability
– Diodes: their ON and OFF states are controlled by the
polarity and magnitude of its voltage and the magnitude of its
current.
– Thyristors: they are turned ON by a control signal and turned
OFF when its current goes to zero
– Controllable switches: both ON and OFF states are
controllable by control signals
![Page 7: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/7.jpg)
7
Ideal Diode
• 2 terminals: A (anode) and K
(cathode)
• It starts to conduct (ON) as long as
the voltage EAK is forward biased
• When ON, it has not voltage drop
• It turns OFF and has no leakage
current when EAK is reverse biased
• Both turn ON and OFF switches are
instantaneous
EAK
EAK
IA
ON
OFF
Ideal I-V characteristics
IA
![Page 8: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/8.jpg)
8
Practical Diodes
• When a diode is forward biased with a voltage about 0.7V or more is applied, it acts
like a closed switch with a negligible voltage drop <1.5V.
• When a diode is reverse biased, it has a negligible current flowing through
• At very large reverse bias, beyond its peak inverse voltage (PIV, 50V-4000V), the
diode breaks down, begins to conduct in reverse and is usually damaged
Real I-V Characteristics
EAK
I A
![Page 9: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/9.jpg)
9
Thyristors
• Usually referred to semiconductor
controlled rectifier (SCR)
• 3 terminals: A (anode), K (cathode) and
G (gate)
• A thyristor behaves like a diode except
that the instant of conduction can be
controlled by “G”; that enables
converting DC to AC
• Two conditions to conduct
1. EAK>0
2. Positive current Ig flows into “G”
for at least a few microseconds
• Once conduction starts, “G” will lose
control and conduction will continue
until the current IA into “A” falls to zero
• If “G” and “K” are short-circuited, the
thyristor is blocked
• A thyristor is partially controllable
EAK
IA
ON
Reverse
blocking
Forward
blocking
OFF
Ideal I-V characteristics
IA
Ig
IA
OFF
ON (if Ig is
applied)
Reverse
blocking
Forward
blocking
Forward
breakdownReverse
breakdown
EAK
Real I-V characteristics
![Page 10: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/10.jpg)
10
Principles of gate firing
• We can control the current in an AC circuit by delaying the gate
(G) pulses with respect to the start of each positive half-cycle.
– If the pulses occur at the very beginning of each half-cycle,
conduction lasts for 180o like a diode
– If the pulses are delayed by , current only flows during the
remaining 180o-
![Page 11: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/11.jpg)
11
Controllable power semi-conductor switches
• With reverse voltage blocking capability
– GTO (Gate-turn-off thyristor)
– IGBT (Insulated gate bipolar transistor)
• Without reverse voltage blocking capability
– BJT (Bipolar junction transistor)
– MOSFET (Metal-oxide-semiconductor field
effect transistor)
MOSFET
E
I
ON
OFF
Reverse
blocking
Ideal I-V characteristics
E
I
ON
OFF
Ideal I-V characteristics
Real I-V characteristics
![Page 12: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/12.jpg)
12
Ideal switch
• Switch from ON to OFF, or vice
versa, instantaneously when
triggered by the control signal
• Vanishingly small power required
from the control signal to trigger the
switch
• When OFF, block arbitrarily large
forward and reverse voltages with
zero current flow
• When ON, conduct arbitrarily large
currents with zero voltage dropE
I
ON
OFF
Ideal
Switch
I
E
+Switch
control signal
![Page 13: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/13.jpg)
13
Real switches
t
t
t
OFF OFF
ON
Switch control signal
E
I
EI
• Have OFF-state leakage current
• Have ON-state voltage (relevant to
conducting losses)
• Limited switching frequency
• Limited forward- and reverse-voltage
blocking capability
– Fewer switches in series are needed with
a higher voltage blocking capability
• Limited ON-state current rating
– Fewer switches in parallel are needed
with a higher ON-state current rating
• Control power is required for switches
– The control circuit can be simplified
with less control power
• Limited dE/dt and dI/dt ratings
– Need additional circuit to limit |EI|
Power loss on the switch
![Page 14: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/14.jpg)
14
− When switch close, energy is transferred from
ES to Eo during time of closure T1
− When the switch opens, energy W stored in the
inductor is dissipated in the arc across the
switch, so efficiency of power transfer is poor
• The voltage step-up/step-down in AC systems
can easily be done with a transformer, but in
DC systems, a DC-to-DC switching converter
is required using a different approach
• To transfer power from a high-voltage DC
source ES to a lower-voltage DC load Eo, one
solution is to connect them by an inductor and
to open and close the circuit periodically
S o
diE E L
dt S oE E
i tL
1 1( ) S oa
E Ei T T I
L
21
2aW LI
Step-down DC-to-DC converter (buck chopper)
![Page 15: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/15.jpg)
15
• To deliver energy W to load Eo when the switch opens, add an diode
oa
Ei I t
L 0o
diL E
dt
2o
a
EI T
L
1S o
a
E EI T
L
If i takes T2 to become zero
2
1
S o
o
E ET
T E
12
= -
(
A
)
+ A
So oE E TE T
• The inductor absorbs energy at a
relatively high voltage (ES-Eo) and
delivers it at a lower voltage Eo
• This circuit enables us to transfer
energy without incurring any losses
• The switch is actually a GTO,
MOSFET or IGBT, whose ON/OFF
state is controlled by a signal
applied to the gate.
![Page 16: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/16.jpg)
16
Rapid switching• Open and close the switch rapidly so that
the current increases and decreases in a
narrow range between Ia and Ib
– When the current falls to Ib (after Tb),
the switch recloses
– When the current reaches Ia (after Ta),
the switch reopens
• Duty cycle:
D=Ta/(Ta+Tb)=Ta/T <1
• Average DC current to the load:
Io=(Ia+Ib)/2
• Average DC current from the source:
IS=Io(Ta/T)=IoD Io=IS/D
• If there is no power loss
ESIS=EoIo=EoIS/D Eo=DES
DC output voltage can simply be
controlled by varying the duty cycle
Io
S o oa b a b
E E EI I T T
L L
![Page 17: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/17.jpg)
17
Impedance transformation
Duty cycle D<1
Io=IS/D Eo=DES
Ro=Eo/Io
RS=ES/IS=(Eo/D)/(IoD)
=Ro/D2
• A step-down DC-to-DC converter (chopper) can transform the
resistance of a fixed resistor to a higher value depending on D.
– It behaves like a DC transformer whose turns ratio is D
– Unlike a transformer allowing power to flow bi-directionally,
a step-down chopper can transfer power only from the high-
voltage side to the low-voltage side
![Page 18: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/18.jpg)
18
Basic 2-quadrant DC-to-DC converter
• Consider two mechanical switches S1 and S2 that open and close alternatively
– Within the time of a cycle T=Ta+Tb, S1 is closed for Ta and S2 is closed for Tb
– S1 has duty cycle D=Ta/T and S2 has duty cycle Tb/T=(1-D)
– Output voltage E12 fluctuates between EH and 0, having the average DC output
EL=DEH (variable by varying D)
• 2-quadrant converter:
– Specific voltage polarity: Terminal 1 is always (+) with respect to terminal 2
– Bidirectional current: current and power can flow from EH to EL, or vice versa
since current always circulate through either S1 or S2
![Page 19: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/19.jpg)
19
• Assume the load to be a battery Eo with
internal resistance R, and use inductor L as
a buffer between the fluctuating E12 and
constant Eo
Average current IL=(EL-Eo)/R
• If average DC voltage EL=Eo, then IL=0 and
no dc power exchange happens
• Step-down chopper (buck mode):
– If EL>Eo, power=|ELIL| flows to Eo
• Step-up chopper (boost mode):
– If EL<Eo, power=|ELIL| flows to EH
• In reality, mechanical switches S1 and S2
are replaced by semi-conductor switches Q1
and Q2 each with a diode placed in
antiparallel for bi-directional currents
• Q1 and Q2 cannot be closed at the same
time to avoid a short-circuit across EH; in
each half cycle, they both open for a very
brief dead time (zero current from EH) for a
safety margin
![Page 20: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/20.jpg)
20
• It consists of two identical 2-quadrant
converters having the same switching
frequency, e.g. 100kHz
• Switching rules:
– Q1 and Q2 on arm A open and close
alternately
– Q3 and Q4 on arm B open and close
alternately
– Q1 and Q4 open and close
simultaneously (duty cycle D)
– Q2 and Q3 open and close
simultaneously (duty cycle 1-D)
• 4-quadrant:
– ELL changes between –EH and +EH
– The DC current flow of the load
connected between A and B can be
from A to B or from B to A
4-quadrant DC-to-DC converter
EA2=DEH
EB2=(1-D)EH
ELL=EA2-EB2=(2D-1)EH
![Page 21: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/21.jpg)
21
ELL=EA2-EB2=(2D-1)EH
![Page 22: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/22.jpg)
22
f
+EL
Io
+
Eo
EL
EH-Eo
-Eo
T= Ta+Tb
Ta
t
Tb
ILQ IL
t
Io
Eo Eo
t
(1 )o oL b
E EI T D T
L L
21(1 )
2 2 2 8 8
oL Lo c
EI I TTQ C E I dt D T
L
22 2(1 ) (1 )0
8 2
o LC
o
E fD T D
E LC f
1
2LCf
LC
• A LC low-pass filter is applied to create
almost flat DC output voltage Eo
• fLC<<f=1/T
Output voltage ripple filter
Ic
2
![Page 23: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/23.jpg)
23
Examples 21-11, 21-12, 21-13
![Page 24: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/24.jpg)
24
DC-to-AC rectangular wave converter
• The 4-quadrant converter with D=0.5 is able to transform a DC
voltage EH into a rectangular AC voltage EH, which contains a fundamental sinusoidal component having an amplitude of 1.27EH
and an effective value of 1.27EH/2=0.90EH
• It is bidirectional (DC-to-AC and AC-to-DC) and frequency-variable
• The output has a fixed amplitude and large 3rd, 5th and 7th harmonics.
f
![Page 25: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/25.jpg)
25
DC-to-AC converter with PWM (pulse width modulation)
• To obtain ELL(t)=Emsin(2ft+), 1
( ) sin(2 )2 2
m
H
ED t ft
E
• 4-quadrant DC-to-DC converter using a carrier frequency fc and different values of D
C
ELL= (2D-1)EH
![Page 26: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/26.jpg)
26
Two DC-to-AC non-sine wave converters with PWM
• With D varying periodically between 0.8 and 0.2 at a frequency f <0.1fc
• Although fc is fixed, the ON/OFF pulse widths change continually with D.
• That is why this type of switching is called pulse width modulation or PWM
![Page 27: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/27.jpg)
27
DC-to-AC sine wave converter with PMW
• To obtain ELL(t)=Emsin(2ft+)
Amplitude modulation ratio m=Em/EH
Frequency modulation ratio mf =fc/f
• Create a 83.33Hz sine voltage wave with a 100V
peak value using a DC-to-AC converter with
EH=200V and fc=1000Hz:
T=1/83.33=0.012s=12000s
Tc=1/1000=1000s
T/Tc=12, so each Tc covers 360/12=30o
Calculate D for (t)=2ft+=0o, 30o, 60o, …,
which correspond to ELL=100sin (V)
In each carrier period Tc, Q1&Q4 are ON for
first DTc =1000D(s) and then Q2&Q3 are ON
for the remaining (1-D)Tc = 1000(1-D) (s)
1( ) sin(2 )
2 2
m
H
ED t ft
E
![Page 28: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/28.jpg)
28
Bipolar PWM and Unipolar PWM
• Once the carrier frequency is filtered out, the resulting voltage will be sinusoidal
• A higher carrier frequency would yield a better sinusoidal waveform but would
increase the power losses of the electronic switches, e.g. IGBTs
![Page 29: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/29.jpg)
29
Creating the PMW pulse trainSwitch Q1 is ON (Q2 is OFF) whenever
EL is above the triangular wave
![Page 30: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/30.jpg)
30
DC-to-AC 3-phase converter
• Switch Q1 is ON (Q2 is OFF) whenever
EAY is above the triangular wave
• Switch Q3 is ON (Q4 is OFF) whenever
EBY is above the triangular wave
• Switch Q5 is ON (Q6 is OFF) whenever
ECY is above the triangular wave
![Page 31: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/31.jpg)
31
![Page 32: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/32.jpg)
32
3-phase, 6-pulse thyristor rectifier (AC-to-DC converter)
• Control the DC output
voltage Ed by the delay
angle of triggering pulses
Ed=1.35Ecos
![Page 33: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/33.jpg)
33
![Page 34: ECE 325 Electric Energy System Components 8- …web.eecs.utk.edu/~kaisun/Backup/ECE325_Fall2015/ECE325_8-Power... · ECE 325 –Electric Energy System Components 8- Fundamental Elements](https://reader031.vdocuments.us/reader031/viewer/2022021901/5b7b30377f8b9adb4c8c1d64/html5/thumbnails/34.jpg)
34
Homework Assignment #7
• Read Chapters 17 and 21
• Questions:
– 17-13, 17-14, 17-15, 17-16, 17-19, 21-25, 21-26, 21-33, 21-34,
21-35
• Due date:
– hand in your solution to Denis at MK 205 or by email
([email protected]) before the end of 11/30 (Monday)