e1t•n · meter centre, cmm design, 5 jaw page 13 meter centre, cmm design, 7 jaw page 14...

Eaton's electrical business is a global leader in electrical control, power distribution, and

industrial automation products and services. Through advanced product development, world-

class manufacturing methods, and global engineering services and support, Eaton's electrical

business provides customer-driven solutions under brand names such as Cutler-Hammer0,

Powerware®, Durant®, Heinemann°, Holes®, and MEMO, which globally serve the changing

needs of the industrial, utility, light commercial, residential and OEM markets. For more

information, visit www.eatonelectrical.ca .

E1T•N

INTEGRATED EQUIPMENT RATINGS APPLICATION HANDBOOK

Eaton Corporation is a diversified industrial manufacturer with 2006 sales of $12.4 billion.

Eaton is a global leader in electrical systems and components for power quality, distribution

and control; fluid power systems and services for industrial, mobile and aircraft equipment;

intelligent truck drivetrain systems for safety and fuel economy; and automotive engine air

management systems, powertrain solutions and specialty controls for performance, fuel

economy and safety. Eaton has 61,000 employees and sells products to customers in more than

125 countries. For more information, visit www eaton com

Eaton Yale Company 5050 Mainway Burlington. ON L7L 5Z1 Canada 1-800-268-3578 www.EatonElectricaloa

E :T•N 0-2007 Eaton Corporation All Rights Reserved Pub. No 20-1773 REV I ) May 2007 Printed in Canada

INTEGRATED EQUIPMENT RATINGS Ea•N

INDEX

Typical Specification Page 3

Introduction Page 4

Description Page 4

Application and Worked Example Page 9

BR Loadcentre, Plug-In Page 11

CBL/CBM Loadcentre, Bolt-On Page 12

Meter Centre, CMM Design, 5 Jaw Page 13

Meter Centre, CMM Design, 7 Jaw Page 14

Pow-R-Line 1a Panelboard Page 15



Pow-R-Line 415P Panelboard Page 19

Cutler-Hammer Transfer Switch Withstand/Closing Ratings 1

Eff•N Page 2 www.eatonelectrical.ca

ET'N

INTEGRATED EQUIPMENT RATINGS

Typical Specification Downstream panelboards must be either Fully Rated or INTEGRATED EQUIPMENT RATED with the upstream protective device.

For INTEGRATED EQUIPMENT RATED panelboards, each panel must be labelled to indicate:

1) tested IER kA rating 2) specific upstream protective device 3) permissible branch devices 4) panelboard designation 5) voltage

All ratings contained herein are based on the latest data available at

time of printing. For further information, consult your Eaton sales representative.

When applying IER to the old style NBA, NGB, NFD panelboards,

please refer to the 2'' edition of 20-1 773(Rev. B) When applying IER to the old style PRL 1, 2, 3 pane/boards and BQL Loadcentres, please refer to the 6th edition of 20-1 773(rev F)

ET'N

INTEGRATED EQUIPMENT RATINGS EtT•N

Introduction Low voltage distribution systems require the general need of continuity of supply and safety to personnel and equipment. The reliable and safe distribution of electrical power is dependent upon the use of protective devices for making and breaking circuits, detecting the presence of fault currents, and for isolating a faulty circuit with least disturbance to the system. In addition, the assemblies which house and provide interconnection points for protective devices play an important role in this reliability and safety perspective. All these matters must be considered when designing, developing, operating and maintaining a modern electrical power system.

Electrical standards of Canada and the USA provide two different methods of applying assemblies such as

panelboards, switchboards, etc. into an electrical system:

• Fully Rated: The short circuit protective devices at all levels have a rating that matches or exceeds

the system available fault level.

• Series Rated or INTEGRATED EQUIPMENT RATED: The electrical standards permit the use of downstream equipment (such as moulded case circuit breaker panelboards) with protective devices having lower interrupting ratings than the available system fault level when protected by an upstream fully rated device. This "series" application of upstream and downstream device must comply with CSA/UL standards which require that any installation supplied in this fashion makes use of devices which have been tested as a series combination.

Description The upstream protective device may be either a moulded case circuit breaker or a fuse (Class R, J, T or L). In the event of a major fault both upstream and downstream devices will open. The let-through current is limited by the simultaneous opening of both devices to a value which can be safely cleared. The upstream device thus protects the lower-rated downstream device. The resultant series rating when applied to a product assembly is known as an INTEGRATED EQUIPMENT RATING.

• Circuit Breakers

A downstream circuit breaker tested in combination with an upstream circuit breaker may be assigned a series connected rating. These circuit breakers can utilize either thermal-magnetic trip units or electronic trip units and can be 80% or 100% rated. When the downstream circuit breaker is tested in a piece of distribution equipment, such as a panelboard, the net result is that the panelboard will have an INTEGRATED EQUIPMENT RATING. Design of the equipment and selection of breakers is based on short circuit interruption tests specified and witnessed by CSA/UL. Because the devices and the equipment are tested as a system, the manufacturer can provide and warrant this INTEGRATED EQUIPMENT RATING.

• Fuses

Don't apply fuses using the up-over-down method. This graphical/empirical method of sizing an upstream current limiting fuse to protect downstream moulded case circuit breakers has been recommended by some fuse manufacturers. This selection process is no longer permissible as the electrical standards will now recognize only tested combinations. Moreover the UP-OVER-DOWN method could lead to erroneous and unsafe conclusions because it treats the circuit breaker as a device with only a static interrupting capacity characteristic. In fact, the circuit breaker has a number of dynamic characteristics at play during fault interruption one of the most dominant being the speed of contact opening. These dynamic characteristics vary greatly between circuit breaker designs.

For proper application of current limiting fuses, always refer to recommendations by the manufacturer of the circuit breaker and its assembly, which are based on actual test data.

• Circuit Protection and Continuity

In applying INTEGRATED EQUIPMENT RATINGS, the design engineer should understand that this technique does not jeopardize circuit protection and continuity when compared to fully rated equipment performance.

INTEGRATED EQUIPMENT RATINGS generally apply to the 600 Ampere and lower feeder level. At the feeder level (i.e. upstream breaker), the device is fully rated. The user level device (i.e. downstream breaker) is a

EitTeN www.eatonelectrical.ca

ETON INTEGRATED EQUIPMENT RATINGS

standard interrupting capacity device. Whether the downstream breaker is fully rated (see figure 1) or JER rated (see figure 2), co-ordination and selectivity remain the same. In BOTH Fully Rated and INTEGRATED EQUIPMENT RATED systems, a downstream fault current higher than the instantaneous trip setting of the upstream breaker may result in both circuit breakers tripping. This situation is usually acceptable when one considers that the vast majority of faults are overloads or limited arcing faults where time-current selectivity still applies. Circuit continuity for INTEGRATED EQUIPMENT RATED systems is the same as for fully rated systems when applied at 600 Amperes and below.

• Fault Calculations/Protection of Downstream Devices and equipment

When applying INTEGRATED EQUIPMENT RATINGS it is only necessary to evaluate the available fault current level (in symmetrical kA) at the line terminals of the main or upstream device. This is sufficient because:

• The upstream/main device (circuit breaker or fuse) is fully rated for the available fault level.

• The upstream device and downstream assembly have a test-proven INTEGRATED EQUIPMENT RATING to meet or exceed the available fault level.

• The let-through current and energy below the downstream breaker is at or below the level of let-through for the downstream device at its rated fault capacity. In this manner downstream cables and loads are protected as normal.

• Selection

To develop a series connected protective system, it is suggested that the design engineer, after completing preliminary steps:

• Define available fault current at the line terminals of the upstream breaker.

• Select an upstream breaker with an interrupting rating equal to or greater than the available fault current.

Verify the INTEGRATED EQUIPMENT RAT-INGS of the selected equipment by referring to the tables in this brochure. Tables show the maximum main or upstream fuse or breaker frame ampere rating. The IER combination applies from the minimum to the maximum fuse or breaker frame rating.

• Confirm, during commissioning, that the correct breakers have been installed by checking the nameplates appearing on the equipment.

. Motor Loads

In most applications, panelboards feed non-motor or low inductance loads, and therefore, there is no requirement to consider motor contribution when selecting series combinations using the IER charts. However, if the downstream panelboard feeds motors through its branch circuit breakers then due consideration should be given to the motor fault contribution.

CEC Part 1, Appendix B, Notes on rules; 14-014 states that "Where motors are connected in the system between the series connected devices, any significant motor contribution to the fault current should be considered. It is generally agreed that the contribution of asynchronous motors to the short circuit current may be neglected if the sum of the rated currents on motors connected directly to the point between the series connected devices is 1% or less of the interrupting rating of the downstream circuit breaker. (See IEC Publication 60781)."

ER RATED DEVICES

INITIAL SHORT-CIRCUIT

CURRENT -

• 1 BRANCH BREAKERS

For those situations where the total motor load is above this level, fully rated circuit breakers should be considered.

www.eatonelectrical.ca


ET.N

100U0

I hour

Io00

102

1

o.I

0-01S 11 IA

Fully ratetl.prs Overcurreiit Aiialvsis. Voltaae Base: 600V. 1232003 9:32:03 AM

3400(TIM)_

Device Name: HKD3400(T/M) Manufacturer: Cutler-Hammer Type: HKD Description: TH-MAG LI Frame/Cartridge: 400.0 A Sensor/Trip: 400.0 A Settings Phase

LTD INST 10.0 (4000A)

FDC3I50

Device Name: FDC3150

\ \ \ Manufacturer: Cutler-Hammer

\ \ \ Type:FDC Description: 150A Frame/Cartridge: 150.0 A Sensor/Trip: 150.0 A

\ \ Settings Phase Opening Clearing Curve

FULLY RATED 35 kA, GOOV

THERMAL MAG

IOA IUOA IkA lOkA lOUkA 1 M

I 0U

Figure 1 - Time-current curves for upstream and downstream breakers that are fully rated.

ET.N www.eatonelectrical.ca


Series Rited.prs Overcurrent Analysis. Voltage Base: 60W. 1232003 9:35:12 AM

•

Device Name: HKD3400(T/M) Manufacturer: Cutler-Hammer Type: HKD

\ \ Description: TH-MAG LI Frame/Cartridge: 400.0 A Sensor/Trip: 400.0 A Settings Phase

\ \ LTD INST 10.0 (4000A)

FDB3I50

Device Name: FDB3150 Manufacturer: Cutler-Hammer

\ \ Type: FDB Description: 150A Frame/Cartridge: 150.0 A Sensor/Trip: 150.0 A Settings Phase

Opening Clearing Curve

SERIES (IER)RATED

I 35 kA, 600V

L THERMAL MAG

IA IDA 10 A 1 k 10k/k 100kA IMA

Figure 2 - Time-current curves for upstream and downstream breakers that are IER rated.

l0000s

1 houi

l000s

lOOs

I mm

lOs

Is

Ols

0.015

ET'IlI www.eatonelectricalCa


ET-,N

INTEGRATED EQUIPMENT RATINGS VALEURS NOMINALES DE PROTECTION INTEGREE DE L'EQUIPEMENT

Voltage

Tension

_LL.

Fault Level!

Courant do Fault

kA synr.)

Branch Breaker!

Disjoncleurs do

derivation

Main or Upstream Breaker Type!

nisjoncteursorinc pal ou an r',ont

y,.sno,toi3O0rsoug SUnG pnrsIboS,0 Is 04 ItotOsLoc IC 00000,,, plug

nuog nosnc DiInrls2,ns p,nsno,0001n. sg,insnoIoggLioIno.

--r du 0.0.57 04ng cgrr.s.000aOls i a0g0, rCs

2.tsIg0000,SSOtgIO$IgIIg$gO,gpSlsl

,rn,,ni00Id.p,n.oIi,,

...,,,,,,,,, IOOA 150A 225A 400A

22

00, nuB, csoa OBOW ED, EDO ED, FD. EDO

001500!DNOA (15-700) .... .... .-- no. En. 405'

SFCBB 500W ED, EDO ED. EDO DO. ED, HOD 10.050. RMsso son ian..,. nova 1SIL05,S,.g. —.y .501100. 01s0 .5,2.

a000,00,os ps o

42

BE, tAB, DNBA ED. EDO ED, EDO ED, PD. EDO

B0IBAE!DNEA (16-70A) GB Fe. SF0 JO, 040 OK, no, SEe

1201240

and let

240

SF000 GB, ED. EDO ED, EDO ED, EDH LCL


VALEGRS NOMINALES DC PROTECTION INTOGREE DE L'EQUIPEMDNT

000W (15.100) GB, Fe, HFD FO, SF0

OBHW FOG FOG JO, 040 DC, ED, 000

SD

BA, Bus, ONBA ED, EDO no, coo ED. EDH. FO , JDG ' BA, BAB, 0500 1670) GO FD, HFD JO, OJD OK, ED, HOD

SF000 GB, ED, EDO ED, EDH ED, EDO LCL

GFCSB 11500! FOG FOG JOG LCL

000W lrS.IDO! GO, ED, SF0 FD,HFD JOG KOC vat.5.,

r.onno,,

IV!

FS1tIIL.0.I1

05000,0

lkA.r' I

5I55nflBl.,k.SI

0.0,00115

FSSSIFSSIOIS

000W FOG FOG JO, OJO DO, CD, 0150

BA, tAB. ONBA EDO, FOG EDO, FOG EOH, OFO, JOG '." 1000 1500 2400 4444 0000

100 GFGOB EDO. FB.TRIPAG EDO EDO LGL 1201142

0041.1

024

100 DA,E,AB.ENBA 10 1 1 0

0011W FOG FOG JOG EDO 02, sos, —AI,C.,00l J,T,nJ,vJ.TJ,T

BA,Bu010NEA )15.100u) F050LFD FOB+LFD LGL LGL 000

200 000W (15.I00A) FGL LGL LCL LCL

GFCBB FGL LGL LOL LGL

Figure 3 Typical Pane/board Label

• CSA/UL Standards Moulded case circuit breakers are designed and tested to CSA Spec. C22.2 #5.1 and/or U/L #489. Both these standards include the test requirements for verifying a series combination rating. The short circuit tests are performed with the upstream device and the downstream circuit breaker mounted in the smallest enclosure in which each is to be used. Two short circuit shots are required; one where the fault is applied with both devices closed, the other by closing the downstream breaker on the fault. After the short circuit shots, the downstream device must pass a calibration check carrying twice rated current and a dielectric withstand test.

An intermediate interrupting test may be required by the testing agency if it is deemed necessary to verify the downstream breaker over the entire range of fault current.

The short circuit test must be repeated if a manufacturer requires • series rating with the downstream circuit breaker mounted in • panelboard.

The series requirements which are now included in C22.2#5.1 are in the CSA Canadian Electrical Code Part I, Rule 14-014, "Series Rated Combinations".

• Panelboard Marking Downstream panelboards containing branch circuit breakers which are being applied on the basis of a series rating must be clearly marked to indicate the following: (Figure #3)

• Short circuit rating • Upstream breaker type • Branch breaker type

Apply and replace breakers prudently since the interrupting capability of an INTEGRATED EQUIPMENT RATED panelboard is based on specific upstream and downstream devices as marked on the panelboard label. It is absolutely essential that any additional or replacement breakers be of the same type and rating as indicated on the label.

. Other Applications of Series (IER) Ratings

Series ratings can also be applied under the following: • Any fully rated breaker can be applied

upstream, downstream or in the middle of any of the series ratings stated in tables.

• Any series rating stated in the tables may have additional series rated branch breakers of the exact same tve further downstream in that rating.

Combining series ratings are allowed under certain conditions. Main and branch ratings may be combined if:

Breakers A, B, and C are in series respectively from main to branch. Breakers Aand B series rate together. Breakers A and C series rate at the same fault level (or higher). Then it is allowable to use A, B and C together at the A-B series rating.

It is improper to combine series ratings under the following condition:

Breakers A, B, and C are in series respectively from main to branch. Breakers A and B series rate together. Breakers B and C series rate at the Breaker B interrupting rating level. It is not allowable to use A, B and C together at the A-B series rating. However combining multiple overcurrent devices as in this example, can be accomplished if all devices in the series combination have been tested together.

ET.N

www. eatonelectrical. ca

ET.N INTEGRATED EQUIPMENT RATINGS

• Summary The utilization of this technique will result in a number of benefits without sacrificing either safety or reliability:

Reduction of Panelboard initial cost and size, since downstream breakers are rated only for the prospective short circuit fault current at their point of application. Requirement of fault calculations for downstream product selection is eliminated.

Downstream circuit breakers are readily available,

volume produced and standard interrupting type.

Anølication and Worked ExamDle

Figure 3 shows a typical schematic that demonstrates the use of Integrated Equipment Ratings. The main Service Switchboard includes a 1600 amp incoming moulded case circuit breaker which feeds a power panelboard in a distribution section of the board. It is assumed that the fault curent of 40 kA is available at the power panelboard bus since the main 1600 amp circuit breaker provides little or no current limitation.

The diagram also indicates that a 400 amp branch breaker in the distribution section feeds a downstream Lighting and Distribution Panel.

• Using the IER Charts The selection of this downstream Lighting and Distribution panel board using Integrated Equipment Ratings is achieved as follows:

Step 1. Look at the given information. (Figure 4)

• System Operating Voltage: 600Y1347V • Fault Level Available: 40kA • Upstream Breaker Amps: 400A

CABI.EIBUS DUCT EOOV 3PH 4W 1500K VA TRANSc

2'4 1 2J MCCB

2XV 2CA cpw CR0 FL

FM

IEI1 I

INCOMING DISTRIBUTION DISTRIBUTION SECTi3I

Figure 4 Typical Schematic Diaa,,,

• Downstream Breakers Amps: 2 and 3 pole 15-150A, 1 pole 15-30A

Step 2. Determine the type of panelboard. • System operating voltage is 600Y/347. There

are two types of panelboards that operate at this voltage: Pow-R-Line 2a and 3a. Since some branches are greater than bOA, the Pow-R-Line 3a must be used.

Step 3. Select and use the IER chart corresponding to the panelboard chosen. (Figure 5)

• First, go to the left most column and select the Voltage Level - for this example: 600Y/347V (A).

• Next, select the Fault Level associated with that voltage from the Fault Level Available column. Use the next highest value if the exact level is not shown - for example: 40kA - go to 42kA (B).

• Now, select the Main or Upstream Breaker Type Amperage. Proceed horizontally to the column with the required ampere rating of upstream device - 400A (C).

• Finally, proceed vertically down from this amperage (C), and horizontally across from the fault level (B). Where these intersect, (D), read the required upstream device, - KDC. Note: If no main or upstream breaker or fuse is shown, then go to a higher fault level that shows a device protecting the particular branch breakers. If one is not shown, then a good combination does not exist.

The upstream device selected is a KDC3400 breaker with standard rated FDB 14kA branch breaker.

That's INTEGRATED EQUIPMENT RATINGS!

TYPE PRLC MAIN SERVICE SWITCHBOARD

TYPSPRL3 LIOF1TIIIC Ala

ST RIBUTI ON PANEISOARD 6000/WV 3014W

www.eatonelectrical ca


Pow-R-Line

Voltage

3aPanelboard:

Max. Fault Level

Avail, at Main or

(kAsym.)

flTh

Branch

Breakers

Upstream device

Main or Upstream

Breaker Type

225A 250A 400A 600A

BA, BAB, DNBA ED, EDH,FD, HFD JD, HJD

QBHW FD, HFD, FDC JD, NJD LD, HLD, Cl-ILD

65 GFCBB,QBAF ED,EDH LCL

120/240 QBAE,GFCBB JD,HJD,JDC

and 240 ED, END, FDB FD, HFD JD, HJD LD, HLD, CHLD

BA, BAG, DNBA EDH, HFD, FDC JDC

QBHW FDC JDC

100 GFCBB, QBAF EDH, HFD. FDC LCL

GHB, GBH EDH, HFD, FDC HJD HLD, CHLD

EHD, FOB, ED EDH, HED, EDC HJD HLD, CHLD

BA, BAB, D NBA (15-IOOA EDBf LED (4) LCL -

QBHW (15-10A) LCL LCL

200 GFCBB,QBAF LCL LCL

GHB, GBH FDC JDC

EHD, EDB, ED, NED FDC JDC

14 GBH (3) EDB, ED, HFD JD, HJD ---- HLD, CHLD

GBH (3) ED, NED JO, HJD ---- HLD, CElLO

18 EDB, ED ED, NED JO, HJD ---- LD, HLD

CLD,CHLD

GBH (3) HFD

600Y/347

25 FDB, FD HED HJD

----

----

--

LD, HLD

CLD,CHLD

and 600 GBH (3) FDC

35 FDB, ED, NED EDO JOC HLD, CHLD

GBH (3) (ED/EDB) + LED (4) 42

FDB, FD, NED --- ---- KDC

GBH (3) (FD/EDB)+ LED (4) 50

EDB, FD, HFD ---- KDC

100 FDB, ED, NED (ED/EDB)+ LED (4) LCL (1) LCL (1)

NOTES: (1) For LCL @ 600V, branch breakers:1 pole 15-70A; 2,3 pole 15-225A. (2) Branch breakers: 2 and 3 pole only. (3) GHBIGBH breakers are suitable for use only on 3 phase 4 wire, grounded wye systems. (4) 150A maximum

Figure 5 Worked Example

www.eatoneiectrical.ca

ET'N


:]:pr7 Plug-in INTEGRATED EQUIPMENT RATINGS 120/24OV AND 24OV, 208Y/ 120V

Max. Fault Level Avail, at Main or Upstream device

(kAsym.)

Branch Breakers

Main or Upstream

Breaker Type

100A 200Al225A 250A 400A

22 BR, DNPL QBHW, BRH ED, EDH DK, KID, HKD, CKD, CHKD GFCB, BRAF, BRCAF QBHW, BRH ED, EDH DK, KD, HKD, CKD, CHKD

25 BR, DNPL CSR GFCB, BRAF, BRCAF CSR

BR, DNPL GHB, GBH, ED, EDH ED, EDH 42 BR, DNPL GHB, GBH, FD, RFD FD, HFD JD, HJD DK, KID, HKD, CKD, CHKD

BRH GHB, GBH, FD, HFD FD, HFD

BRH FDC FDC JD, HJD DK, KID, HKD, CKD, CHKD GFCB, BRAF, BRCAF GI-IB, GBH, ED, EDH ED, EDH JD, HJD KD, LCL

BR, DNPL GHB, GBH, ED, EDH ED, EDH JD, HJD DK, KID, HKD, CKD, CHKD 65 BRH (15-b OA) GHB, GBH, FD, HFD ED, HFD

BRH EDH, EDC, FDC EDH, EDC, FDC JD, HJD DK, KID, HKD, CKD, CHKD GFCB,BRAF,BRCAF GHB, GBH, ED, EDH, FDC ED, EDH, FDC ---- DK,KD,HKD,LCL,CKD,CHKD BRAF,BRCAF,GFCB ---- ---- JDC

BR, DNPL EDH, EDC EDH, EDC JDC

100 BRH EDH, EDC, FOC EDH, EDC, FDC JDC KDC GFCB,BRAF,BRCAF I EDH, EDC, EB-TRIPAC EDH, EDC JDC LCL

:I1!TFi1 Plug-in INTEGRATED EQUIPMENT RATINGS 120/240V AND 240V, 208Y/ 120V

Max. Fault Level Avail, at Main or Upstream device

(kAsym.)

Branch

Breakers

Main or Upstream

Fuse Type

bOA 200A 400A

65 GFCB,BRAF,BRACRF J,T J,T -

100 BR/DNPL(15-100A) J,T,R J,T J,T

100 CC J,T J,T J,T

www. eatonelectrical. ca


ET.N

CBM/C BL IrnIUT B olt-o n/Pow-R- Line 1R INTEGRATED EQUIPMENT RATINGS

120/240V and 240V; 208Y/120V

Max. Fault Level

Avail, at Main or

(kAsym.)

Branch

Breakers

Upstream device

Main or Upstream

Breaker Type

100A 225A 250A BA,BAB,DNBA QBHW ED, EDH

22 QBGF,QBAF QBHW ED, EDH

BA,BAB,DNBA ED, EDH, GI-IB, GBH ED, EDH JD, HJD QBGF, QBAF GHB, GBH, ED, EDH ED, EDH

42 QBHW GHB, GBH, ED, HFD FD, HFD QBHW FDC FDC JD, HJD

BA,BAB,DNBA ED, EDH, GHB, GBH ED, EDH JD, JDC, HJD QBGF, QBAF GHB, GBH, ED, EDH ED, EDH

65 QBAF,QBGF FDC, GHB, GBH FD QBHW - GHB, GBH, ED, HFD FD, HFD JDC OBHW FDC FDC JD, HJD

M!WL'I :1 U!TT 11T :111i7j 11'' R- Line hi; INTEGRATED EQUIPMENT RATINGS

120/240V and 240V; 208Y/1 20V

Max. Fault Level

Avail, at Main or

(kAsym.)

Branch

Breakers

Upstream device

Main or Upstream

Fuse Type

100A 150A 200A

100 BA,BAB,DNBA J,T J,T J,T

200 BA/BAB/DNBA (15-100A) J,T,R J,T J,T

ETON www.eatonelectrical.ca


Meter Centre: _ INTEGRATED EQUIPMENT RATINGS

208Y/120V 3ph 4w, or 120/240 1 p 3w Maximum System Voltage

MaxFault Level Tenant/Remote! Suite Main or Upstream

Avail, at Main or Panel Main Panel Breaker Type

Upstream device Breakers Breakers

400A 600A 800A 1200A (kA sym.)

DK, KID, BR (15-100), CSR

DNPL, BAB, DNBA, BR, GFCB, BRAF, HKD,CKD,

BRCAF, QBAF CHKD 22

BRH, DNPL, BAB, DNBA, BR, GFCB, BRAF, CHH-H2, CSR BRCAF,QBAF

DK, KD, BR (15-70)

DNPL, BAB, DNBA, BR, GFCB, BRAF, HKD, CKD,

BRCAF, QBAF CHKD

BRH, DNPL, BAB, DNBA, BR, GFCB, BRAF, OK, KD, LID, CLD,

42

CHH-H2 BRCAF,QBAF HKD,CKD, HLD,

CHKD CHILD DK, KD, LD, CLD, ND, HND,

BRHH, DNPL, BAB, DNBA, BR, GFCB, BRAF, HKD,CKD, HLD,

MDL, NDC,CND,

CHH-H4 BRCAF,QBAF CHKD CHLD

CMDL CHND,CNDC

DK, KID, LO, CLD, ND, HND,

65 BRHH DNPL, BAB, DNBA, BR, GFCB, BRAF,

HKD,CKD, HLD, MDL, NDC,CND, BRCAF, QBAF

CHKD CHLD CMDL CHND,CNDC

Meter Centre: CMM Design, 5 Jaw INTEGRATED EQUIPMENT RATINGS 208Y/120V 3ph 4w, or 1201240 lph 3w Maximum System Voltage

Max. Fault Level Tenant/Remote! Suite Main or Upstream

Avail, at Main or Panel Main Panel Fuse Type

Upstream device Breakers Breakers

400A 600A 800A 1200A (kA sym.)

22 CSR, BR (15-100) DNPL, BAB, DNBA, BR, GFCB, BRAF,

J,T J,T BRCAF, QBAF

BR, BRH, DNPL, BAB, DNBA, BR, GFCB, BRAF, J,T J,T

CHH-1-12 BRCAF,QBAF 42

BRH, BRHH DNPL, BAB, DNBA, BR, GFCB, BRAF,

J,T J,T T T BRCAF, QBAF

BR, BRH, BRHI-1 DNPL, BAB, DNBA, BR, GFCB, BRAF,

J,T J,T ____________ BRCAF, QBAF

65 BRH,BRHH

DNPL, BAB, DNBA, BR, GFCB, BRAF, J,T J,T T T

BRCAF, QBAF

BR, BRHH, BRH DNPL, BAB, DNBA, BR, GFCB, BRAF,

J,T J,T

BRCAF, QBAF

100 BRH,BRHH DNPL, BAB, DNBA, BR, GFCB, BRAF,

J,T J,T T T BRCAF, QBAF

CHH,EDC,EDH DNPL, BAB, DNBA, BR, GFCB, BRAF,

J,T J,T T I BRCAF, QBAF

ET.N wweatonelectrical.ca


ET'N

Meter Centre : CMM Design, 7 Jaw INTEGRATED EQUIPMENT RATINGS 208Y1120V 3ph 4w Maximum System Voltage

Max. Fault Level Tenant/Remote/Panel Main Suite Main or Upstream Avail, at Main or Breakers Panel Breaker Type Upstream deice Breakers

200A 400A 600A (kA sym.)

DNPL. BAB, DNBA, BR, GFCB, BRAF, CC, GD, ED BRCAF,QBAF ED

DNPL, BAB, DNBA, BR, GFCB, BRAF, 22 CC, GD BRCAF,QBAF DK DK, KD, HKD, CKD, CHKD

DNPL, BAB, DNBA, BR, GFCB, BRAF, CC, GD, ED BRCAF,QBAF DK DK, KD, HKD, CKD, CHKD HLD, CHILD

DNPL, BAB, DNBA, BR, GFCB, BRAF, - CC, GD, ED BRCAF,QBAF ED

DNPL, BAB, DNBA, BR, GFCB, BRAF, 42 CC, GD BRCAF, QBAF DK DK, KD, HKD, CKD, CHKD

DNPL, BAB, DNBA, BR, GFCB, BRP,F, CC, GD, ED BRCAF,QBAF DK DK, KD, HKD, CKD, CHKD HLD, CHILD

DNPL, BAB, DNBA,BR, GFCB, BRAF, 65 CC, GD, ED BRCAF,QBAF ED DK, KID, HKD, CKD, CHKD

DNPL, BAB, DNBA, BR, GFCB, BRAF, - 100 CC, GD, ED BRCAF,09AF EDH

i'iFiZ'flflJ7 INTEGRATED 7EQUIPMENT :7V1IL* 208Y/120V 3ph 4w Maximum System Voltage

Max. Fault Level Tenant/Remote/Panel Main Suite Main or Upstream Avail, at Main or Breakers Panel Fuse Type Upstream device Breakers

200A 400A 600A (kA sym.) DNPL, BAB, DNBA BR, GFCB, BRAF,

22 CC, GD, ED BRCAF, QBAF J, T J, T J, T DNPL, BAB, DNBA, BR, GFCB, BRAF, -

42 CC, GD, ED BRCAF,QBAF J, T J, T J, T DNPL, BAB, DNBA, BR, GFCB, BRAF,

65 CC, GD, ED BRCAF, QBAF J, T J, T J, T DNPL, BAB, DNBA, BR, GFCB, BRAF, -

100 CC, GD, ED BRCAF, QBAF J,T J, T J, T

TENANT BREAKER

WATTHOUR METER

100A

METER bOA CENTRE #1

(TYPICAL 35 METERS)

100A

100A

100A

100A

SUITE PANEL 208Y/1 20V OR 120/240V 1PH3W

TRANSFORMER I 600 to 208Y/1 Lkk_AJ 3PH4WOR ,--- 600 TO 120/240V

1 PH 3W

METER CENTRE #3

METER CENTRE#2

6CDA

600A

600A

PAN ELBOARD 1200A 208W1 20V 3PH 4W

Figure 6 Meter Centre Application

ET.N

www.eatoneleCtriCal.Ca


Pow-R-Line la Panelboard: INTEGRATED EQUIPMENT RA TINGS

120/240V and 240V; 208Y/1 20V

Max. Fault Level

Avail, at Main or

(kAsym.)

Branch

Breakers

Upstream device

Main or Upstream Breaker Type

IOOA 225A 250A 400A 600A

22 BA, BAD, DNBA QBHW ED, EDH JD, HJD DK, KD, HKD, CKD, CI-IKD __

QBGF,QBAF,QBGFEP QBHW ED, EDH DK, KD, HKD, CKD, CHKD

BA, BAB, DNBA ED, EDH, GHB, GBH ED, EDH

BA, DAB, DNBA ED, HFD JD, HJD DK, KID, HKD, CKD, CHKD 42 QBGF,QBAF,QBGFEP GHB, GBH, ED, EDH ED, EDH LCL

QBHW GHB, GBH, FD, HFD ED, HED

QBHW FDC FDC JD, HJD DK, KD, HKD, CKD, Cl-IKD HLD.CHLfl

BA, BAB, DNBA ED, EDH, GHB, GBH ED, EDH JDC

BA, BAB, DNBA GHB, GBH (1) JD, HJD DK, KD, HKD, CKD, CHKD

65 QBGF,QBAF,QBGFEP GHB, GBH, ED, EDH ED, EDH LCL

QBGE,QBAE,QBGFEP FDC FDC JDC LCL

QBI-tW GHB, GBH, ED, HFD ED, HED JDC KDC

QBHW FDC EDC JD, HJD DK, KD, HKD, CKD, CHKD 1LD,CHLD

100

BA, DAB, DNBA EDH, HED, FDC EDH, EDC JDC

QBGF,QBAF,QBGFEP EDH, HED, EB-TRIPAC EDH, EDC LCL

QBHW FDC FDC JDC KDC

200

BA/BAB/DNBA (15-10A) (ED/EDB)+ LED (ED/EDB)+ LED (2) LCL LCL

QBHW (15-10A) ECL LCL LCL LCL

QBGE,QBAE,QBGEEP FCL LCL LCL LCL

(1) 1P 15-70A , 2P, 3P 15-b OA.

(2) 150A maximum

Pow-R-Line la Panelboard: INTEGRATED EQUIPMENT RATINGS

120/240V and 240V: 206Y/120V

Max. Fault Level

Available

(kAsym.)

Branch

Breakers Main or Upstream Fuse Type

bOA 200A 400A 600A

65 QBGE,QBAE J,T J,T ----

100 BA/BAB/DNBA(15-100A) J,T,R J,T J,T T

200 BA/BABJDNBA (15-10A) J,T,R J,T ----

www.eatonefectricaLca


Pow-R-Line 2a Panelboard: INTEGRATED EQUIPMENT RATINGS

Voltage Max. Fault Leval

Avail, at Main or

(kA sym.)

Branch

Breakers

Upstream device

Main or Upstream

Breaker Type

100A 225A 250A 400A

208Y1120

and 240

100 GHB, GBH

EDH, HFD EDH, HFD HJD HKD, CHKD

200 FDC FDC JDC KDC, LCL

480Y/277

(2)

25

GHB, GBH

ED, HFD ED, HFD JD, HJD KD, HKD, CKD, CHKD

65 HFD HFD HJD (1) HKD/CHKD

100 FDC FDC JDC, LCL KDC (1), LCL

200 (FD/FDB)+ LFD (FD/FDB)+ LFD (3)

600Y/347

(2)

14

GBH

FDB, FD, HFD FDB, FD, HFD KID, HKD, CKD, CHKD, KDC

18 FD, HFD FD, HFD KD, HKD, CKD, CHKD, KDC

25 HFD HFD

35 FDC FDC

50 (FD/FDB)+LFD I (FD/FDB)+ LFD (3)

Notes: (1) Branch Breakers: 1 pole 15-1OA; 2,3 pole 15-50A. (2) GHB/GBH breakers are suitable for use only on 3 phase 4 wire grounded Wye systems. (3) 150A maximum

Pow-R-Line 2a Panelboard: INTEGRATED EQUIPMENT RATINGS

Voltage Max. Fault Leval Avail, at Main or

(kA sym.)

Branch Breakers

Upstream device

Main or Upstream Fuse Type

100A 200A 400A

208Y/120

and 240

100 GHB, GBH J,T,R J,T,R J,T

200 J,T,R J,T J,T

480Y/277

(1)

100 GHB, GBH J,T,R J,T,R J,T

200 J,T,R J,T J,T

600Y/347 100 GBH J, T J, T

(1)

Note: 1. GI-IB/GBH breakers are suitable for use only on 3 phase 4 wire grounded wye systems.

www.eatonelectricatca

INTEGRATED EQUIPMENT RATINGS Ea•N

Pow-R-Line 3a Pane!board: INTEGRATED EQUIPMENT RATINGS

Voltage Max. Fault Level

Avail. at Main or

Upstream device

(kA sym.)

Branch

Breakers Main or Upstream

Breaker Type

225A 250A 400A 600A

120/240

and 240

65

BA, BAB, DNBA ED, EDH,FD, HFD JD, HJD DK, KD, HKD, CKD, CHKD ----

QBHW FD, HFD, FDC JD, HJD DK, KD, HKD, CKD, CHKD LD, HLD, CLD, CHLD

QBGF, QBAF, QBGFEP ED, EDH LCL LCL ----

QBAF, GFCBB ---- JD, HJD, JDC ---- ----

ED, EHD, FDB FD, HFD JD, HJD DK, KD, HKD, CKD, CHKD LD, HLD, CLD, CHLD

100

BA, BAB, DNBA EDH, HFD, FDC JDC LCL ----

QBHW FDC JDC KDC ----

GFCBB, QBAF, QBGFEP EDH, HFD, FDC LCL LCL ----

GHB, GBH EDH, HFD, FDC HJD HKD, CHKD HLD, CHLD

EHD, FDB, FD EDH, HFD, FDC HJD HKD, CHKD HLD, CHLD

200

BA, BAB, DNBA (15-100A) FDB+ LED (4) LCL LCL ----

QBHW (15-100A) LCL LCL LCL ----

QBGF, QBAF,QBGFEP LCL LCL [CL ----

GHB, GBH FDC JDC KDC, LCL ----

EHD, FDB, FD, HFD FDC JDC KDC, LCL ----

480Y/277

and 480

(2)

22 GHB,GBH --- JD,HJD KD, HKD, CKD, CHKD

25 GHB,GBH,EHD,FDB FD,HFD JD, HJD HKD, CHKD ---

35 GHB,GBH,EHD,FDB,FD FD - KD, HKD, CKD, CHKD ----

EHD, FDB, FD ---- ---- ---- LD, HLD, CLD, CHLD

65

GHB, GBH (15-50A) FDC HJD HKD, CHKD ----

GHB,GBH,EHD,FDB,FD FDC ---- FIKD, CHKD ----

EHD,FD,FDB FDC HJD HKD, CHKD ----

END, FDB, FD FDC ---- HLD, CHLD

100 EHD,FDB,FD,HFD FB-P, FDC LA-P,JDC KDC ----

150 EHD,FDB,FD,HFD FCL ---- LCL

600Y/347

and 600

(2)

14 GBH FDB, FD, HFD JD, HJD KD, HKD, CKD, CHKD LD, CLD, HLD, CHLD, [DC

18

GBH FD, HFD JD, HJD KD, HKD, CKD, CHKD LD,CLD, HLD, CHLD, LDC

FOB, FD FD, HFD JD, HJD

----

KD, HKD

CKD, CHKD

LD, HLD

CLD, CHLD,LDC

25

GBH HFD ---- ---- ----

FDB, FD HFD HJD

----

KD, HKD

CKD, CHKD

LD, HLD

CLD, CHLD,LDC

35

GBH FDC ---- ----

FDB, FD, HFD FDC JDC

----

HKD, CHKD HLD, CHLD, LDC

42 GBH (FD/FDB)+ LFD (3) ---- ---- ----

FOB, FD, HFD, FDC (FD/FDB)+ LFD (3) ---- KDC ----

65 GBH (FD/FDB)+ LED (3) - -- ----

FOB, FD, HFD, FDC ---- ---- KDC ----

100 FOB, FD, HFD, FDC (FD/FDB)+ LED (3) [CL (1) [CL (1) ----

NOTES: (1) For LCL @ 600V, branch breakers:1 pole 15-70A; 2,3 pole 15-225A. (2) GHB/GBH breakers are suitable for use only on 3 phase 4 wire, grounded wye systems. (3) 150A maximum

EIT•N www.eatonelectrical.ca


ET.N

iPow-R-Line

Voltage

3aPanelboard:

Max. Fault Leel

Avail. at Main or

Upstream deuce

(kAsym.)

Branch

Breakers

Main or Upstream

Fuse Type

100A 200A 400A 600A

120/240

and 240

100

____________

BA, BAB, DNBA J,T J,T J,T

QBHW J,T J,T J,T

GHB, GBH J,T,R J,T,R J,T J,T

EHD, FDB, FD, HFD J,T J,T J,T J,T

200

BA, BAB, DNBA J,T J,T

QBHW J,T J,T - --

GHB, GBH J,T J,T J,T --

480Y/277

and 480

100 GHB/GBH (1) J, T, R J,T,R J,T

EHD,FDB,FD,HFD,FDC J, T, R J,T J,T J,T

600Y/347

and 600 100 GBH (1) J, T J, T --

FOB, FD, HFD, FDC J,T,R J,T J, T

NOTE: 1. GHB/GBH breakers are suitable for use only on 3 phase 4 wire, grounded wye systems.

ww. eatonel ectrical. ca


Pow-R-Line

Voltage Max Fault Level Branch Main or (stream

Avail, at Main or Breakers Breaker Type

Upstream device 400A 600A 800A (kAsym.)

65 BA, BAB, DNBA DK, KD, HKD, CKD, CHKD,LCL ED, EHD, FDB DK,KD,HKD,CKD,CHKD,LCL LD, HLD, CLD, CHLD

GHB, GBH HKD, CHKD, LCL HLD, CHLD EHD, FDB, FD HKD, CHKD, LCL HLD, CHLD HMDL, CI-IMDL 120/240 100

JD, DK, KD, LD, CKD, CLD HKD, CHKD, LCL HLD, CHLD and 240 200 GI-IB, GBH, EHD, FDB, FD, HFD, KDC LCL

JD, 1-UD, DK, KD, HKD, CKD, CHKD ,

35 EHD. FDB, FD, JD KD, HKD, CKD, CHKD LD,HLD, CLD,CHLD

65 HKD, CHKD HLD, CHLD 480Y/277 JD, KD,LD, CKD, CLD and 480 100

EHD, FDB, ED, HFD KDC

JO, HUD, KD, HKD, CKD, CHKD

25 FOB, ED, JD CKD, CHKD, KD, HKD LD,HLD, CLD,CHLD, LDC

600Y/347 FDB, ED, HFD, HKD, CHKD HLD, CHLD, [DC and 600 35 KD, LD, CKD, CLD

JD, HJD HKD, CHKD

42 FDB, ED, HFD, FDC, KDC JD, _HJD,_KO,_HKD,_CKD,_CFIKD

50 JD, WD, KD, HKD, CKD, CHKD KDC

FDB, FD, HFD, FDC KDC

65 KD, HKD, CKD, CHKD KDC FDB, ED, HFD, EDC KDC

100 FDB, ED, F-fED, FDC, [CL (2) JD, _I-IJD,_KO,_HKD,_CKD,_CHKD

NOTE: 1 For PRL 1a/2a sub chassis, refer to the respective charts. 2. For LCL @ 600V, F-Frame branch breakers: 1 pole 15-70A; 2, 3 pole 15-225A.

IF AT*N www.eatorielectrical.ca


1TTZ Panelboard:

Voltage Max. Fault Level

Avail, at Main or Upstream device

(kAsym.)

INTEGRATED EQUIPMENT

Branch Breakers

Main or Upstream

Fuse Type

400A 600A

120/240 and 24C 100

GHB, GBH J,T EHD, FDB, FD

JT

200 GHB, GBH J,T

480Y/277 and 480

100

EHD, FDB, FD, HFD JT JT KD, HKD, LD, HLD, CKD, CHKD, CLD, CHLD

KD, HKD, CKD, CHKD J, T, R J,T

JD, HJD J,T J, T

200 KD, HKD, CKD, CHKD J,T

600Y347

and 600 100

FDB, FD, HFD, FDC J,T

KD, HKD, KDC, LD, HLD, CKD, CHKD, CLD, CHLD J,T J,T

KD, HKD, KDC, CKD, CI-IKD J, T, R J,T

JD, HJD J,T

200 KD, HKD, KDC, CKD, CHKD J,T

www. eatonelectri cal. ca

ET.N


Cutler-Hammer Transfer Switch Withstand / Closing Ratings

When protected by an upstream, any manufacturers breaker or Cutler-Hammer circuit breaker as shown, the transfer switch is rated for use on a circuit capable of delivering not more than the RMS Symmetrical amps at the voltage shown below.

Voltage Transfer Switch Ampere Rating

Number of Poles Switched

Maximum fault level available at upstream device (kA symmetdcsl) Upstream any manufacturers' breaker or Cutler-Hammer circuit breaker type ___________

25kA 351kA 421kA 5OkA 65kA lOOluf, 200kA 30-200 2,3,4 Any* Any. Any* Any* Any Any. FDC,JDC,KDC

225 2 Any* Any* Any* Any* Ay Any* FDC,JDC,KDC 120/240 and 300 23,4 Any* Any* Any* Any Any Any* KDC

240, 208Y/120 400 2,3,4 Any* Any* Any* Any Any Any* KDC 600 2,3,4 Any* Any* Any* Any* Any* Any* LDC

800- 1000 2,3,4 Any* Any* Any* Any* Any* Any __________

30-150 2,3,4 Any Any* Any* Any* Any* (FDB/FD)*LFD FDC,JDC,KDC

150kA FCL*** , LCL*

200-300 2,3,4 Any* Any* Any* Any* Any KDC,NB-TP LCL***

480Y/277 and 400 2,3,4 Any Any* Any* Any* Any* -

480 600 2,3 Any* Any* Any* Arty* Any* NB-TP 800 2,3 Any* Any* Any* Any* --- NB-TP --

600- 1000 4 Any* Any* Any Any*

1000 2,3 Any* Any Any* Any* --

30- 150 2,3,4 Any Any* (FD/FDB)-iLFD KDC

(FD/FDB)+LFD KDC

(FD/FDB)vLFD KDC

(FD/FDB)*LFU LCL

600Y/347 and 200-300 2,3,4 Any* Any Any* KDC KIDC LCL --

600 400 2,3,4 Any* Any* Any* KDC KDC - -- 600 2,3 Any* Any* Any* LDC 600 4 Any* -- - - -

800-1000 2,3,4 Any* Any nanulacturers Dreacer -- WItfl Piz uniter lOUISA maximum uaiioiui

Cutler-Hammer TrannSwitch Withstand Closing Ratings When protected by an upstream fuse type shown, the transfer switch is rated for use on a circuit capable of delivering not more than the RMS Symmetrical amps at the voltage shown below.

Voltage Transfer Switch Ampere Rating

Number of Poles Switched

Madmum fault level available at upstream device (kA symmetrical) ________

Upstream ruse Type Max Fuse Amperes lOOkA 200kA

120/240 and 240, 208Y/120

30-225 2,3,4 ____________ J,T 200A J,T - 400A

300 ___________

2,3,4 ____________

R J,T 400A J,T -- 600A

400 2,3,4 J,T R 600A

L -- 1200A

600 2,3,4 L -- 800A

L 1600A

800-1000 2,3,4 -- L 1600A

480Y/277, 48C, 600Y/347 and

600

30-150 2.3,4 -- ___________ J,T 200A

J,T - 400A

200-300 ___________

2,3,4 ____________

R J,T 400A J,T -- 600A

400 _____________

2,3,4 ______________

J,T R 600A L -- 1200A

600 2,3 L -- 800A

L 1600A 600 4 --- L 1600A

800-1000 2,3,4 -- L 1600A U41 5)1W!

www.eatoneleCtriCal Ca


ET.N

ET.N wweatoneIectri cal. ca

e1t•n · meter centre, cmm design, 5 jaw page 13 meter centre, cmm design, 7 jaw page 14...

Documents