e r ua ators man o p l - button11. check all fixing screws are secure and tight. 4 liftmaster a...
TRANSCRIPT
LIFTMASTER
WARNINGThis equipment requires installation by persons
with appropriate electrical qualifications and training and must be wired in accordance to
AS3000 wiring rules
FEATURES[ High speed
-800mm/second [ Corrosion resistant - Hot dip galvanised base with stainless steel cover[ Speed flexibility - Slow start / slow stop with fast open - slow close for additional safety
[ Compact - Motor and controls all under
the same key lockable cover[ Safety - An inbuilt clutch and isola-
tion switch under the cover[ Emergency use - Simple motor discon- nect for power fail situations[ Voltage - 240V supply
SR MO AT NA UR AE LPO
MAGIC BUTTON FS10 & LPK5FAST SLIDER
R
TABLE OF CONTENTS
As Liftmaster Electronics policy is one of constant improvement, we reserve the right to alter any part of these specifications without notice and without incurring any obligation.
LIFTMASTER ELECTRONICS PTY LTD A.B.N. 58 000 266 035PO BOX 54 ALEXANDRIA NSW 1435 AUSTRALIA PH: 61 2 9699 9654 FX: 61 2 9699 8443
www.liftmaster.com.au
1. FS10 INSTALLATION . . . . . . . . . . . . . . . page 3 - 41.1 Preliminary Checks 31.2 Installing the Operator 31.3 Fixing the Drive Rack 4
2. LPK5 INSTALLATION . . . . . . . . . . . . . . . . . . 5 - 62.1 Preliminary Checks 52.2 Installing the Operator 52.3 Fixing the Drive Rack 6
3. ELECTRICAL . . . . . . . . . . . . . . . . . . 7 - 93.1 Wiring Connections 73.2 Step Down Limit Configuration 83.3 Control Board Instructions 83.4 Photo Electric Wiring 83.5 Speed Inverter Instructions with Step Down Speed 9
4. Limits . . . . . . . . . . . . . . . . . . 104.1 Limit Switch Function 104.2 Setting the Limits 10
5. GENERAL MAINTENANCE & SETUP . . . . . . . . . . . . . . . . . . 115.1 Disengagement Lever 115.2 Slipping Clutch 115.3 Safety 115.4 Lubrication 11
6. TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . 126.1 Fault Finding Guide 12
7. PARTS EXPLOSION . . . . . . . . . . . . . . . . . . 13-147.1 FS10 Parts List 137.2 LPK5 Parts List 14
8. F.A.Q . . . . . . . . . . . . . . . . . . 158.1 Frequent Question 15
LIFTMASTER MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
3
1. FS10 INSTALLATION
1.1 Preliminary Checks
To ensure trouble free operation, make sure that the gate (whether existing or to be installed) has the following specifications.
! Strong and rigid gate frame manufactured to appropriate engineered standards ! The gate moves freely and evenly over its entire travel and does not jam on start up from either direction - especially with cantilevered gates! No sideways oscillation movement of the leaf! Upper and lower sliding system in perfect condition with appropriate rated wheels and rollers! Adequate mechanical gate stops which have been appropriately engineered are manditory ! The gate has sufficient extension for mounting the drive rack (Fig. 1)
If any welding or brazing is required on the gate, it should be done before installing the automation system. The condition of the structure directly affects the reliability and safety of the automation system
1.2 Installing the Operator
1. Lay the conduits and cables between operator, accessories and power supply. The flexible pipes must protrude approx. 2cm from the cable entry hole. To facilitate the electrical wiring on the electronic system, leave about 45cm of free cable out of the bore in the base plate.
2. Unpack the operator and check that all accessories are included in the parcel.3. Open the cover of the operator by means of the key supplied.4. Place the base plate in the position shown at Fig. 1 (for left or right hand mounting).5. Ensure surface is perfectly level and mark the bolt hole positions; These should be positioned in the
slot at the further most point away from the gate (This is to allow the operator to be slid in and out of the drive rack). Remove operator and drill for bolting down with 4 x 12mm x 100mm Dyna bolts or equivalent. Before bolting down place 2mm shims, as a temporary measure, between the ground surface and the base plate. These are to be removed after the rack has been correctly attached tothe gate (See 1.3).
6. Connect the cables to the electronic control unit (refer to section 3).
LIFTMASTER
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
Fig. 1
17
8.5
550320
80
Min. 200 X
70
120165
61
.5
65100
21
.5
Cable Entry
25
TOP GUIDE
RACK
FS10Left Hand Opening
OPEN
GATE POST
X
Right Hand Opening
OPEN
65 165
Min. 200
320120 100
21
.5
Cable Entry70
550
17
8.5
61
.58
0
25
1.3 Fixing the Drive Rack
1. Fit the rack by means of: - 12g tek screws for Nylon rack (not supplied).- the supplied screws for Steel rack.
It is advisable to tighten the rack fixing screws at the centre of the slot.This allows the rack to be adjusted up and down if gate drop occurs.
2. Release the operator as shown in Fig.13 3. Slide gate leaf open by hand.4. Place the first section of the rack on the pinion, aligning it with the
first spacer (tab on nylon rack).5. Fix the rack section to the leaf by means of a clamp.6. Slide the gate leaf by hand towards its closed position, until it is in
line with the last spacer/tab on the rack and spot weld the spacer in position (Screw the tabs for the nylon rack).
7. For the steel drive rack, completely weld the three spacers to the gate. To fasten the other rack sections needed to reach the position of complete closing, proceed as follows.
8. Line up another drive rack length to the last one fixed on the gate. Use a section of rack of about 150mm long and clamp this section to the two lengths of drive rack to ensure that the teeth correctly mesh (Fig.4).
9. Slide the gate leaf by hand towards its closed position until the third spacer of the section to be fastened is aligned with the pinion (Fig. 4). Weld the three spacers to the gate. Repeat this process until all rack is installed.
Ensure that all the rack sections are correctly centred on the pinion teeth (Fig. 3). If not, adjust the position of the operator. Do not weld the rack sections to the spacers or to each other.
Fig. 2
Steel Drive Rack
Nylon DriveRack
STEEL RACK SHOWN DO NOT weld pieces together
2m
m
Fig. 4
Fig. 3
10. Manually check whether the gate can open completely and the movement of the leaf is smooth and even, over its entire travel.
The slack between the pinion and the rack must be 2mm (Fig. 3 & 4). If the gate is new, check the slack a few months after installation. Do not apply grease or other lubricants to the pinion or rack.
11. Check all fixing screws are secure and tight.
4
LIFTMASTER
ANylon Rack - 110mm
Steel Rack - 150mm
Rack Mounting Heights
This measurement is from the groundto the centre of the rack mounts.
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
FS10
gate bottom railmin. 150mm
2mm packing shim during installationto be removed after rack is installed
A
295
355
38
0
5
LIFTMASTER
Fig. 5
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
2. LPK5 INSTALLATION
2.1 Preliminary Checks
To ensure trouble free operation, make sure that the gate (whether existing or to be installed) has the following specifications.
! Strong and rigid gate frame manufactured to appropriate engineered standards ! The gate moves freely and evenly over its entire travel and does not jam on start up from either direction - especially with cantilevered gates! No sideways oscillation movement of the leaf! Upper and lower sliding system in perfect condition with appropriate rated wheels and rollers! Adequate mechanical gate stops which have been appropriately engineered are manditory ! The gate has sufficient extension for mounting the drive rack (Fig. 5)
If any welding or brazing is required on the gate, it should be done before installing the automation system. The condition of the structure directly affects the reliability and safety of the automation system
2.2 Installing the Operator
1. Lay the conduits and cables between operator, accessories and power supply. The flexible pipes must protrude approx. 2cm from the cable entry hole. To facilitate the electrical wiring on the electronic system, leave about 45cm of free cable out of the bore in the base plate.
2. Unpack the operator and check that all accessories are included in the parcel.3. Open the cover of the operator by means of the key supplied.4. Place the base plate in the position shown at Fig. 5 (for left or right hand mounting).5. Ensure surface is perfectly level and mark the bolt hole positions; These should be positioned in the
slot at the further most point away from the gate (This is to allow the operator to be slid in and out of the drive rack). Remove operator and drill for bolting down with 4 x 12mm x 100mm Dyna bolts or equivalent. Before bolting down place 2mm shims, as a temporary measure, between the ground surface and the base plate. These are to be removed after the rack has been correctly attached tothe gate (See 2.3).
6. Connect the cables to the electronic control unit (refer to section 3).
LPK5
Left hand Opening Right hand Opening
GATE POST
OPEN OPEN
Min. 450
30
73
115
470 50
570
Cable Entry
X Min. 250
10
01
6
100 110
Cable Entry
X
RACK
TOP GUIDE
2.3 Fixing the Drive Rack
1. Fit the rack by means of: - 12g tek screws for Nylon rack (not supplied).- the supplied screws for Steel rack.
It is advisable to tighten the rack fixing screws at the centre of the slot.This allows the rack to be adjusted up and down if gate drop occurs.
2. Release the operator as shown in Fig.13 3. Slide gate leaf open by hand.4. Place the first section of the rack on the pinion, aligning it with the
first spacer (tab on nylon rack).5. Fix the rack section to the leaf by means of a clamp.6. Slide the gate leaf by hand towards its closed position, until it is in
line with the last spacer/tab on the rack and spot weld the spacer in position (Screw the tabs for the nylon rack).
7. For the steel drive rack, completely weld the three spacers to the gate. To fasten the other rack sections needed to reach the position of complete closing, proceed as follows.
8. Line up another drive rack length to the last one fixed on the gate. Use a section of rack of about 150mm long and clamp this section to the two lengths of drive rack to ensure that the teeth correctly mesh (Fig.8).
9. Slide the gate leaf by hand towards its closed position until the third spacer of the section to be fastened is aligned with the pinion (Fig. 8). Weld the three spacers to the gate. Repeat this process until all rack is installed.
Ensure that all the rack sections are correctly centred on the pinion teeth (Fig. 7). If not, adjust the position of the operator. Do not weld the rack sections to the spacers or to each other.
STEEL RACK SHOWN DO NOT weld pieces together
2m
m
Fig. 8
Fig. 7
10. Manually check whether the gate can open completely and the movement of the leaf is smooth and even, over its entire travel.
The slack between the pinion and the rack must be 2mm (Fig. 7 & 8). If the gate is new, check the slack a few months after installation. Do not apply grease or other lubricants to the pinion or rack.
11. Check all fixing screws are secure and tight.
6
LIFTMASTER
ANylon Rack - 130mm
Steel Rack - 165mm
Rack Mounting Heights
This measurement is from the groundto the centre of the rack mounts.
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
LPK5
Fig. 6
Steel Drive Rack
Nylon DriveRack
195
145
Gate BottomRail.
Min 150mm
54
0
A
10
0
MB106 WIRING INSTRUCTIONS USING TAIAN E2-201-H1F INVERTER
ON
OF
F
ON
OF
F
12
WARNING240VAC
CO
M
OP
EN
0V
PE
NC
PB
PE
D
+12V
L9L8
L7L6L5L4L3L2L1
JP2
MB106REV 01
GN
D
AN
T
Transformer 240/12V 0.5 Amp
8 10 111213141516171819
CN
O
CN
O
RFI Filter
1 2 3 4 5 6 7
Activ
e
Ne
utr
al
CO
M
OP
EN
CLO
SE
Mo
tor
Ca
pa
cito
r
Connect to main Earth
Op
en
R
ela
y
Micro Controller
P.E
. F
use
1A
Fu
se
5x2
0m
m
5A
Fu
se
5x2
0m
m
Clo
se
Re
lay
LCD Display
OPT02OPT01
5 4 6
3 7
8
2
1
9 0
2
1
6
Rec
eive
r123
JP3
1 2
3 4
5
CLO
SE
Mo
tor
Lim
its
NC
C
CO
M
CO
M
9
AU
X
RE
LAY
LINK 31
34
ISOLATING SWITCHON / OFF
24
0V
50
Hz
SU
PP
LY
A
N
E2
1
5
4
BL
AC
K
BL
UE
WH
ITE
BL
UE
RE
D
BLUE
RED
3 PHASEMOTOR
L1N
SP1
FWD/CLOSE
REV/OPEN
12/COM
T1
- U
T2
- V
T3
- W
Inverter
6
3
4
5
White
Blue
Black
White
Motor Overload
3. ELECTRICAL3.1 Wiring Connections
7
LIFTMASTER
Fig. 9
UP
DOWN
NEXT
SET
Link 2 & 3 (for invertor)
3
4
6
7
5
BLUE (FROM JP3)
WHITE (FROM JP3)
C
N.O
C
N.ORed 2nd Close Limit
FWD (Close)
REV (Open)
SPI 40Hz Closing Speed
RST 20Hz Speed
+12 COM
White
Yellow 2nd Open Limit
Black (from JP3)
9
Yellow
7
13
11
Blu
e
Wh
ite
Inverter Terminals
WIRING DIAGRAM FOR STEP DOWN SPEED CONTROL
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
RED, Close step down limit
YELLOW, Open stepdown limit
BLACK, Close stop limit
GREEN, Open stoplimit
LIFTMASTER
3.2 Step Down Limit Configuration
3.3 Control Board Instructions
For detailed control board information, please refer to the control board instruction manual.
8
Closing: the step down limit (red) is set 10 degrees before the final close limit (black). The red limit will
ndstart the 2 speed and the gate will move at 20Hz speed for small distance then the gate will stop on the black limit.
Opening: the step down open limit (yellow) is set 10 degrees before the final open limit (green). The
ndyellow limit will start the 2 speed and the gate will move at 20Hz speed for small distance then the gate will stop on the green open limit.
For details on adjusting the limits, refer to section 4
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
3.4 Photo Electric Wiring
2.4.1 All photo electrics used with the Magic Button FS10 or LPK5 MUST have an Earth wire connected between 0V supply terminal and the photo electric steel case or any other metal plate next to the photo electric (E.g. Gate jamb, post, track etc)
3.4.2. RIB Photo Electric Wiring (500211) 3.4.3. Mini Photo Electric Wiring (500212)
Note: JP1 jumper shouldbe ON for both PE’s)
A+ A- 8
11 12 14
10
13
Earth to casingon receiver only
1 2 3
11 12 14
4
13Earth to casingon receiver only
Note: For other brands of photo electrics, refer to the manufacturers instructions
3.5 Speed Inverter Instructions with Step Down Speed
TAIAN INVERTER PROGRAMMING
Note: These are settings for the running frequency, acceleration time and deceleration time. Refer to the inverter booklet for other functions.
SETTING DISPLAY COMMENT5.0
60
F00
F01
05.0
1
F01
F02
5.0
1
F02
F08
10
40
F08
F10
000
1
F10
Running Frequency
Set Running Frequency to 60Hz
Acceleration time function
Acceleration time set to 1
Deceleration time function
Deceleration time set to 1
Closing frequency set to 40Hz
Operating Mode
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Turn Power ON
Press till 60
Press DSP FUN
Press DATA ENT
Press DATA ENT
Press DATA ENT
Press DATA ENT
Press DATA ENT
Press DATA ENT
Press DATA ENT
60 End ProgrammingPress DSP FUN
Press till 1
Press till 1
Press till 2
Press DATA ENT
Press till 0.5
Press till F08
Press till 40
Press till F10
Press till 1
Press till F05
Press DATA ENT
Press till 2
Press DATA ENT
Press DATA ENT
Press till 20
Press DATA ENT
1
2
F05
6.0
20
F09
28
29
30
31
36
Press till F09
Press till F20
Press DATA ENT 05
Press till 1
Press DATA ENT F20
F05
F09
F20
001
Step down speed
LIFTMASTER
9
Press till F13 13
Press DATA ENT 000
Press till 5 5
Press DATA ENT
32
33
34
35
Torque compensation gain
F13
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
LIFTMASTER
10
MAXIMUM TRAVEL TRAVEL OVER RUN
Fig. 10
4.1 Limit Switch Function
NOTE: Care should be taken to ensure the limit switch roller does not over travel the limit cam (See Fig. 10). A high speed and long slow down time will cause the motor to over run the limits allowing the gate to continue its travel in the same direction causing damage to the gate and motor.
Adjustment ScrewAdjustment Screw
Lock NutLock Nut
Fig. 11
4.2 Setting the limits
To adjust the limits, remove the limit cover (refer to Fig. 14). The coarse adjustment of the limit switches can be done by inserting a rod or screw driver into one of the adjustment holes of the cam wheels and moving in the direction required. Fine adjustment can be done two ways - (1) by increasing or decreasing the speed on the inverter, or(2) by screwing the adjustment screw (refer Fig. 12) against the cam shaft thread inside each cam wheel. The adjustment screw is supplied inside each limit switch box. The screw must be changed from one adjustment hole to the other for turning the cam wheel in the opposite direction.
Note: Before starting adjustment of the limit switches, loosen or tighten (if necessary) the lock nut in order to obtaina convenient ADJUSTMENT TIGHTNESS of the cam wheels. After finishing the adjustments, make sure that the lock nut is sufficiently tight to retain the cam wheels during operation (refer Fig. 11)
Fine AdjustmentFine Adjustment
Coarse AdjustmentCoarse Adjustment
Fig. 12
4. LIMITS
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
Fig. 13
5. GENERAL MAINTENANCE & SETUP5.1 Disengagement lever
aM
nu
al
Disengagement Lever
In power failure or emergency situations the disengagement lever is provided to allow the gate to be opened manually. By turning the disengagement lever the gear unit can be disconnected from electric operation in order to permit manual operation of the gate.Before disengagement, isolate the power.
NOTE: When changing the disengagement lever back to electric operation, the gate itself must be moved manually, slightly in either direction in order for the clutch to get perfectly engaged.
LIFTMASTER
11 MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
5.2 Slipping Clutch
The torque transmitted by the drive unit must always be adjusted in due consideration of the safety requirements of the gate operation. The limitation of the torque is done by adjusting the slipping clutch.
When supplied from Liftmaster, the slipping clutch is left loose so that no torque can be transmitted from the electric motor.
Adjustment: (Refer Fig. 14) 1. Loosen the lock nut at the end of the worm shaft.
Correct lubrication is of primary importance for the function of the worm gear. The oil grade of the initialfilling is shown on the rating plate of the gear box (refer Fig. 14). In normal operating conditions oil changes are not necessary. The oil quantity, however, should be checked at the time of the installation as well as periodically in connection with normal maintenance and adjustments in the gate function. The red oil plug of the gearbox shows the required oil level.
The normal oil (Mobil Gear Oil 627 or equivalent) is applicable for an environment with temperaturevariations from -15°C to +45°C. For lubrication in especially low or high operating temperatures werecommend consulting with Liftmaster for appropriate oil.
5.4 Lubrication
Fig. 14
Clutch Adjustment Screw
Clutch Lock Nut
Worm Shaft
Rating Plate of the Gear Box
Slipping Clutch Lining
Limit Cover
5.3 Safety
The installation of appropriate safety devices applicable for the situation is mandatory. Possible safety accessories include warning signs, photo electrics, vehicle detectors, safety edge profile, emergency stop controls, flashing lights, and traffic lights.
2. Hold the worm shaft with a spanner. 3. Start turning the adjustment screw inwards (clockwise) until the required torque has been obtained.The torque should be adjusted so that it is just high enough to move the gate over its complete traveland low enough to permit the clutch to slip as soon as the gate is obstructed in its movement. A directsafety risk is produced if the torque is set to a considerably higher level than required for the gate operation.
IMPORTANT: Before starting to adjust the slipping clutch, check and make sure that the gate can easilybe moved manually in every part of its travel.
LIFTMASTER
12
Tu
rn th
ere
lea
se
clu
tch
to m
an
ua
l use
Ca
nth
e g
ate
be
mo
ve
d e
asi
lym
an
ua
lly?
NO
NO
Re
mo
ve
ob
stru
ctio
ns
an
d o
bsta
cle
s p
reve
ntin
gg
ate
mo
vem
en
t
NO
NO
Ch
eck
ga
tero
llers
NO
NO
Ch
eck th
ere
lea
se
clu
tch
fun
ctio
n
YE
SY
ES
NO
NO
Fix
/ a
dju
st
the
re
lea
seclu
tch
YE
SY
ES
In “
ha
lf o
pe
n”
po
sitio
no
bse
rve
re
lays
wh
ilep
ressin
g p
ush
bu
tto
ns
FU
NC
TIO
NS
IN
BO
TH
DIR
EC
TIO
NS
FU
NC
TIO
NS
IN
BO
TH
DIR
EC
TIO
NS
Th
em
oto
rru
ns?
NO
NO
Me
asu
reth
e p
ha
secu
rre
nts
ON
E P
HA
SE
MIS
SIN
GO
NE
PH
AS
E M
ISS
ING
Rig
ht
volta
ge
in e
very
ph
ase
?
NO
NO
Ma
in c
ircu
itfa
ulty
YE
SY
ES
Ph
ase
bro
ken
in th
e m
oto
rw
ind
ing
Re
pla
ce
the
mo
tor
Me
cha
nic
al
fau
lt in
th
e m
oto
r
NO
NO
Re
lea
se th
esl
ipp
ing
clu
tch
YE
SY
ES
OK
OK
YE
SY
ES
Is th
eg
ea
r sh
aft
turn
ing
?
NO
NO
Ad
just
or
rep
lace
th
esl
ipp
ing
clu
tch
Ge
ar
tee
th o
rre
lea
se
clu
tch
bro
kenN
ON
O
Re
pla
ce
ge
ar
un
it
YE
SY
ES
Ch
eck
drive
sh
aft
keyw
ay
NO
FU
NC
TIO
NN
O F
UN
CT
ION
Ch
eck th
eth
erm
al r
ela
y in
the
co
ntr
ol b
ox
Ch
eck
fuse
s
Ch
eck
wh
eth
er
the
mo
tor
is
ove
rhe
atin
g
Ch
eck
mic
rosw
itch
es in
mo
tor
&lim
it sw
itch
bo
x
Ch
eck
“clo
sed
” lim
itsw
itch
circu
it
Ch
eck
sa
fety
circ
uits
Ch
eck
“op
en
” lim
itsw
itch
circu
it
Fa
ult
in th
eco
ntr
ol b
ox
log
ic c
ircu
its
FU
NC
TIO
NS
ON
LYIN
TH
E “
CL
OS
ED
”D
IRE
CT
ION
FU
NC
TIO
NS
ON
LYIN
TH
E “
CL
OS
ED
”D
IRE
CT
ION
FU
NC
TIO
NS
ON
LY IN
T
HE
“O
PE
N”
DIR
EC
TIO
NF
UN
CT
ION
S O
NLY
IN
T
HE
“O
PE
N”
DIR
EC
TIO
N
Fig. 15
6. TROUBLE SHOOTING6.1 FAULT FINDING GUIDE
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
LIFTMASTER
13
TITLE:
DATE:
SCALE:
DRAWN BY:
DRAWING No:
CHECKED BY:
CF
MBFS10 PARTS EXPLOSION
NTS spare_parts
08/08/06
LIFTMASTER
11
33
44
55
66
77
88
991010
1111
22
1212
12 Motor 0.55kw
Gear Box & Limit Assembly
3
Base Plate
4 Cover
56
Magic Button Control Board7
PVC Control Box
8
Inverter
9
Shaft
10
Sprocket - Z2511Mounting Plate
Lock
12
Isolation Switch
No.No. ITEMITEM No.No. ITEMITEM No.No. ITEMITEM
RH
7. PARTS EXPLOSION7.1 FS10 PARTS LIST
MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
Left Hand
10a10a Right Hand
3a3a
Left Hand
Right Hand
LIFTMASTER ELECTRONICS P/LTITLE:
DATE:
SCALE:
DRAWN BY:
DRAWING No:
CHECKED BY:
DS
OVITOR LPK5 EXPLOSION
NTS ovi-lpk5exp.304.ds
25/2/04
11
22
33
44
77
66
88
991010 1111
No.No. ITEMITEM
1 Gear Box & Limit Assembly2 Motor 0.55kw1 Gear Box & Limit Assembly
3 Base Plate4 Cover5 Isolation Switch6
Magic Button Control Board7Control Box - PVC
8 Inverter9 Shaft10 Sprocket - Z2511 Mounting Plate (optional)
LIFTMASTER
7.2 LPK5 PARTS LIST
14 MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
55
M8 Socket Screw
LIFTMASTER
8.1 FREQUENT QUESTION:What size and weight gate can this operator handle and how fast does it close/open?
ANSWER:Gate weight is often used as a criteria for gate motor selection. The first issue of gate motor selection is whether the gate is well engineered, manufactured and installed and can be moved by a force of 400 kiloponds (approximately what one man can move by hand) These requirements are fundamental to every gate installation. The start torque of the FS10 at 50Hz is 144 kg with the 36:2 gearbox or 196 kg with the 29:1 gearbox, and as such the FS10 has a start torque that far exceeds 400 kiloponds. Gate weight becomes of concern when safety needs are examined, as any fast moving gate, regardless of weight, needs to have sufficient safety devices to provide a prudent operation. Any risk assessment of gate speed involves the potential need of how to stop the gate mass, if required, before it meets the end limits and the mandatory, suitably engineered to suit, open and close gate stops.
As the gate motor speed is achieved by an inverter there will ALWAYS be approximatelyone (1) second of slow down before the gate motor will be without power and the motor brake engages. A risk assessment of the distance the gate will travel in one second is dependent upon the selected inverter frequency selection and must be taken into account..
The heavier the gate, the more the gate speed should be lowered to achieve an acceptable stopping distance for the application, in the event of an emergency stop. The speed can be altered by lowering the frequency, at 80Hz the gate speed with a 36:2 gearbox is 800mm / sec. , and at this speed the mass of any size gate will be hard to stop in an emergency. Over travel before stopping will be significant, while the slower the speed the less the over travel. This contingency has to be taken into account in any installation, as also the possibility of programming separate speeds for open and close cycles.
The 36:2 gearbox is standard, while the 29:1 gearbox is available on special order.
Gate travel of over ten (10) metres will require four (4) external limits to be installed.
If in any doubt with regard to any issue consult a qualified engineer.
TECHNICAL DATAPower Supply Required
Absorbed Power (Watts)
Current Drawn (Amps)
Electric Motor
Standard Reduction Ratio
Pinion Size
Rack
Type of Oil
Temperature Range
Weight of Operator
240V AC
550 W
4 Amp
4 Poles - 1370 RPM
36 : 2
Module 4
Mobil Gear 627 (or equivalent)
-15°C to +45°C
42 kg
Z25 (110mm diam.)
29 : 1
Max Speed with 36:2 800mm/sec
480mm/sec
Start-up Torque with 36:2 144 kg
196 kg
80 kg
326 kg
Locking Torque with 36:2
Optional Reduction Ratio
Start-up Torque with 29:1
Locking Torque with 29:1
Max Speed with 29:1
Nominal Torque with 36:2 91 kg
Nominal Torque with 29:1 124 kg
15 MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL
8. F.A.Q.
DISTRIBUTED BY:
NOTES
As Liftmaster Electronics policy is one of constant improvement, we reserve the right to alter any part of these specifications without notice and without incurring any obligation.
LIFTMASTER ELECTRONICS PTY LTD A.B.N. 58 000 266 035PO BOX 54 ALEXANDRIA NSW 1435 AUSTRALIA PH: 61 2 9699 9654 FX: 61 2 9699 8443
www.liftmaster.com.au
LIFTMASTER
16 MAGIC BUTTON FS10 & LPK5 - 0907 - REV02
MAGIC BUTTON FS10 & LPK5 FAST SLIDER - OPERATORS MANUAL