[email protected] your supplier, daniel diamond“d” lifting eve qualitv checklist a normalizedprior...

Cavitv Number_ FRONT Liftino Eve BACK

Diamond “D” Logonufactwng trademark 01

the Edward W Daniel Company

Physical Testing:Each lot of standard llfbna eves is manu-factured and tested accoidinb to ASTMA489-93 and ANSI 818.15.BREAKING STRENGTH: The threadedshank IS screwed into one jaw of a testingmachine and a pin secured to the otherjaw passed through the eye.BEND TEST: Unthreaded parts must becapable of being bent to pressure or blowsthrough 45’ wlthout showing cracks orindications of failure.TENSILE TEST: Per ASTM A489.

PLAIN & SHOULDER LIFTING EYESMaterial Data:Grade Cl030Heat Treat Quench & Draw

Mechanical Properties:Grain Size 5 or FinerTellSlIeYield

65,000 PSI ml”

Elongatron30,000 ps, ml”30% ml”.

Reduchon of Area 60% m,n

Diamond “D” Lifting Eyes are processedand tested to the above requirements. Testsare performed on randomly selected lifttngeyes from a given heat lot.

e=-----@ rE$__Application:(a) Loads should always be applied to liftingeyes in the plane of the eye, not at someangle to this plane(b) Shoulder lifbng eyes must be properlyseated (should bear firmly against the matingpart) otherwise the working load.; must bereduced substantially. A steel washer or spacermay be required for proper seating(c) No greater load should be allowed thanthat given under rated capacity in each of thetables of dimensional data(d) To obtain greatest strength from a liftingeye. it must fit reasonably tight In the holeinto which it is screwed to prevent unscrewmgdue to twst of cable Tightness and seatingmust be checked after initial load.(e) Liftmg eyes should never be painted orotherwise coated when used for lifting. assuch coatings will very likely cover up flaws.(f) To attain the rated capacity listed forregular lifting eyes, full thread engagementallowing l/2 turn for alignment to the plane ofthe eye is necessary.

WARRANTY: No warranty is given as to the fitness for any particular purpose of the described goods.CERTIFICATIONS: Request for certification(s) must be made at time of order entry and there will be a charge associated withthe certification.

L I F T I N G E Y E C A P A C I T I E S -DIAMETER

IN. MM

RATED CAPACITY0” 450 over

LBS. KGS LBS KGS 45”500900

1,3001 8002.4003,2004 0005 0007 0009 000

12 00015 00021 00028 00038 00056 000

i::ij(1 030)

il ::q(2 1401

IZ,!&q

i$%i(8.970)

(11.960)(16.230)(24,200)

NOTE ON LIFTING EYE 8 NUT EYE BOLT RATED CAPACITIESAll rated lifting capacities included in the product charts are based

on full sized shank and eye unaltered, and unaltered threading.

I Lifting Eye Capacities & Safety InformationRated Capacity: The max~~m recommendedload that should be exerted on the Item at zero

Yield Strength: The mawnum stress that can

degree vertical pull. All rated load values are forbe applied to a material wthout pe rmanen tdeformation of the material.

pulls exerted I” the plane of the eye

Ultimate Strength: As defined in the machln-(St’s handbook is. the stress at which a materlalin tension. compression, or shear WIII ruptureor fracture

Safety Factor: An Industry term denotingtheoretical capability. Ltfhng eye rated capacityIS figured with a 5 to 1 safety factor for a zerodegree straight vertical pull.

CopyrIght 1995 The Edward W Dame Co

-

LIFTING EYES - Carbon and Alloy SteelLifting Eyes, Plain and Shoulder Pattern; Reduced Lifting Eyes.. .............................................. 1Metric, DIN 580, Alloy and Reduced Alloy Lifting Eyes ............................................................... 2NUT EYE BOLTS -Shoulder Pattern ................................................................................ 3P A D “D” EYES. . ................................................................................................................... 3NUT EYE BOLTS -Plain Pattern, Blanks.. ....................................................................... 4A L T E R N A T E L I F T I N G D E V I C E S............................................................................... 5Standard and Special Sizes, ........................................................................................................ 6Blanks, Machined and Alloy.. ....................................................................................................... 7EYE NUTS - Carbon SteelStandard Sizes.. ........................................................................................................................... 7TURNBUCKLES - Carbon Stee lTurnbuckle Bodies and Stub End Turnbuckles.. .......................................................... .............. 8Eye & Eye, Hook & Eye and Hook & Hook Models.. .................................................................. 9Jaw & Eye and Jaw&Jaw Models.. ........................................................................................... 10Oval Eye & Oval Eye, Hook &Oval Eye and Jaw & Oval Eye Models.. .................................... 11Stub End Fittings......................................................................................................................... 12Jaw Fittings.. ................................................................................................................................ 13Oval Eye Fittings.. ........................................................................................................................ 14Hook Fittings.. .............................................................................................................................. 15Round Eye Fittings ...................................................................................................................... 16ANCHOR SHACKLES - Carbon Stee lScrew Pin and Round Pin -American Made and imported.. ....................................................... 17WIRE ROPE FITTINGS - Carbon SteelWire Rope Clips - Forged and Malleable; Safe-Line Clamps.. ..................................................... 18Thimbles - Regular and Heavy Duty............................................................................................ 19HOOKS - Carbon SteelChain Slip, Chain Grab, Clevis Slip and Clevis Grab.. ................................................................. 20CHAIN HARDWARE - Carbon SteelDouble Clevis Links, Connecting Links, Chain Repair Links and Cold Shuts.. ........................... 21BLUE DIAMONDTM WROUGHT NUT EYE BOLTS . Carbon SteelBent Eyes and Bent Eyes-Welded Closed.. .............................................................................. 22BLUE DIAMONDTM U-BOLTS - Carbon SteelU-Bolts - Round and Square, Strap Washers.. ............................................................................ 23HOOKS AND SCREW EYE BOLTS - Carbon SteelClothes Line Hooks, Porch Swing Hooks, Lag Screw Eyes, S-Hooks andForged Screw Eye Bolts .............................................................................................................. 24FLANGES - Carbon SteelMedium Heavy Pilot-Type, Extra Heavy Flat-Type, Forged TankandStandard Heavy Curved Flanges.. .............................................................................................. 25Standard Heavy Flat-Type; Trimmed, Special Heavy Straight, Pilot andComposite Flanges ..................................................................................................................... 26MISCELLANEOUS PRODUCTSHand Held Alloy Safety Hooks, Malleable Bevel Washers, Set-Up Wedges,Wedge Shims and Wall Angle Brackets.. .................................................................................... 27Plastic Yokes, Forged Steel Adjustable & Plain Yoke Ends and Clevis Pins.. ............................ 28Strap Ends, TEE Bolts, Tarpaulin Rings and Lifting Lugs ............................................................ 29STAINLESS STEEL HARDWAREIntroduction to section.. ................................................................................................................ 30EYE BOLTS - Stainless SteelEye Bolts, Plain and Shoulder Pattern; Nut Eye Bolts and Eye Bolt Blanks.. ........................... .31Plain and Shoulder Pattern 316 Blanks.. .................................................................................... 32ROD ENDS, EYE NUTS - Stainless SteelStandard 304 and 316 Sizes.. ..................................................................................................... 32TURNBUCKLES - Stainless SteelTurnbuckle Bodies ....................................................................................................................... 32Eye & Eye, Jaw & Eye, Jaw &Jaw, Oval Eye &Oval Eye, Jaw&Oval Eyeand Stub End Models .................................................................................................................. 33Round Eye, Oval Eye, Jaw and Stub End Fittings.. ................................................................... 34WIRE ROPE FITTINGS, WROUGHT EYE BOLTS,U-BOLTS - Stainless SteelWire Rope ClipsandThimbles - Regular&Heavy Duty; Wrought Eye Bolts: U-Bolts .............. 35FLANGES, ADAPTORS, DRUM PLUGS - Stainless SteelStandard Heavy Flange Straight Pilot and Tri-Sure Flanges; Drum Flanges&Drum Plugs ...... 36ELEVATOR MAINTENANCE HARDWAREElevator Sockets, Wedge Sockets, Socket Bolts.. ................................................................. 37Rail Shims (Single & Double Slot). ......................................................................................... 38Rail Clips, Socket Bolt Springs.. ............................................................................................. 39

EDWARD W. DANIEL CO. I

PLAIN PATTERNForged l 1030 Carbon SteSelf-Colored

REDUCED LIFTING EYESForged * 1030 Carbon SteelSelf~Colored

“” ‘--13621 5116-18 1 ‘h G 1%. 2791~~ RI3621 8.5 90013631 318-16 1 ‘I4 1 l”/ls 3 RI3631 14.0 1.30013638 7116-14 1% 1% 11%6 3% R13638 19.0 1,80013641 112.13 1 ‘h 1%. 2% 3 % R13641 29.5 2.40013650 9116-12 1% 1% 2% 5 % R13650 44.0 3.20013661 518-l 1 1% 1% 2% 6 4% RI3661 56.0 4.00013672 3,410 :‘/4 1 ‘h 2’%s 47% RI3672 66.5 5.00013662 718-9 l”/Ie 33/G 5% RI3682 129.0 7,00013702 1-6 2% 1’s 3% 6 6% RI3702 198.5 9,00013712 1-118-7 2% 2 4’/16 6% RI3712 292.0 12.00013723 1-114-7 3 2’s 4%6 7% R13723 396.0 15,00013753 1-112-6 3% 2% 5 % 6% R13753 654.0 21,00013770 I-314-5 3% 27% 6 91%6 RI3770 1050.0 28.00013780 2-4-I 12 4 3% 6% 11 R13780 1580.0 38.00013790 2-112-4 5 4 6% 13% _ 2900.0 56.000

Part #13650 dimen*ions not in accordance with ANSI 818.15.

Know Your Supplier, Daniel Diamond “D”Lifting Eve Qualitv Checklist

a Normalized prior lo machining.. Heat treated for strength and desired properties.. Roll threads I/4” ttlru I-l/Z”.

J . Cut thread* 1-314” thr” 2.112”.*ASTM A489 test data available on request.*Shoulder style lining eye 114” fhw 1” military style

collar-MS51937 specification.

Proof Tested To InsureFinest Quality

0 EDWARD W. DANIEL CO.

Apgnx. Cmt.?,

stllcx Metric 2% Tk:d Sim”k 1.0.

“0. size l”Ches A ““B”” Eel t; fy: q2 3K e:sly1w PCS. I” llgs

1461lM M6 % M6 x 1.0 25.4 19 30.0 60.3 16.5 4.7 21014621M M7 %. M7 Y 1.0 26.5 22 36.5 71.4 23.2 9.0 37014631M MB 3/a M8 x 1.25 31.7 25 43.0 62.5 27.6 15.2 50014636M Ml0 '/I 6 MlOx1.5 35.0 27 46.0 90.5 30.9 23.0 74014641M Ml2 'A MlZx1.75 36.0 30 54.0 100.6 34.0 33.0 1.0301466lM MI4 G8 Ml4 x 2.0 44,514662M MI6 % Ml6 x 2.0 44.514672M Ml8 % Ml6 x 2.5 51.014662M M20 '/a M20 x 2.5 57.014702M M24 1 M24 x 3.0 63.514712M M27 1% M7.7 Y 3.0 70.014723M M30 1% M30 x 3.5 76.014753M M36 1% M36 x 4.0 69.014760M M42 1% M42 x 4.5 95.014770M M45 1% M45 x 4.5 95.014775M M48 1% M4B Y 5.0 101.614760M M5.2 2 M52 x 5.0 101.6'Plain Pattern available upon request.

65.0 120.7 40.9 63.6 1,60065.0 120.7 40.9 63.6 1,600715 ,333 447 96" 714"

22020 MC?0 72 40 16 30 71 40 2.5 100.0 1200All dimensions are in millimeter*.‘Nominal diameter.

14702LT 1 2% 1's. 3%, 6 % 2%6 222.0 11.60014723LT I-1,4 3 ws 4%s B1/52 2'%8 444.0 18.40014753LT I-112 3% 2% 5%. 9'%, 3%. 736.0 26.600._ 3'/, .." .-- ,,-14780LT 2 4 6 % 11 % 4% 1670.0 471600

mead 0.0. 1.0. Overall Thread P.ppnx.

To? o’a.I ‘r Ep k?th Le7’h wt. Pl, RatedBI1”kI. 4”” D__ *_“__L

139OOLT 1% 2% 1% 45% '/a min. HRE 125BLK.66213905LT 1% 3's 1% 5% 1% min. HRE 150BLK.6620 216 13.700139lOLT 2 4% 2% 6% l%r min. HRE ZOOBLK-6620 440 20.00013915LT 2% 43/, 2% "" liisemin. H R E 250BLK.66207% 695 26:ooo

‘Blanks have no rated capacity

METRIC LIFTING EYESForged l 1030Carbon SteelSelf-Colored l Shoulder Pattern'

METRIC LIFTING EYESDIN 580 Except HeatTreated 1030Steel

4LLOY LIFTING EYES

ALLOY REDUCEDLIFTING EYESForged * BWOAlloy Steel

I_, . . ,

11479OLT

EDWARD W. DANIEL CO. E

NUT EYE BOLTSForged l Shoulder PatternHot Galvanized l 1030 Carbon Steel*

SPECIAL SIZESFor

Ped . Shoulder Pattern

Sel -Colored 1030 Carbon Steel*

- Available up to l’%rs” I.D.

E EDWARD W. DANIEL CD.

RATED CAPACITY IS DRASTICALLY REDVCED WHEN LOADING AT ANY ANGLE.LOADING MUST NEVER BE MADE AT AN ANGLE GREATER THAN 46O FROMBOLT CENTERLINE. AT AN ANGLE OF 46°. RATED CAPAClTY IS REDUCED TO114 OF THE TABULATED VALVE.

Threaded with Nuts *Thread Shank Appror.

Stock ma Length wt. Per RatedNO. A B

q100 PCS. capm1ty

12310 '/4 2 '/2 6 40012312 '/4 3 % 7 40012314 '/4 4 % 8 40012315 '/412316 '/4

z % 11 400'/2 13 400

12319 =/m 2 % =/s 11 80012321 % 6 3 =/a 13 80012323 % 6 4 S/a 15 80012325 %6 z 5/e 17 80012326 %6 % 20 80012330 % 2 % J/4 17 1,20012331 3/a 3 % 21 1,20012333 %12334 %

d'/z % 1,200%

;:1,200

12335 =/8 5 =/4 27 1,20012336 3/u % 30 1,20012338 3/s

:% 36 1,200

12339 3/s 10 % 40 1,20012340 '/2 3 % 1 40 2,10012341 '/2 4 1 41 2,10012343 '/2 1 42 2,10012345 %

:1 55 2,100

12347 % IO 1 67 2,10012348 'I2 12 1 75 2,100

SPECIAL ‘/2 AL 1 2,10012350 % 4 1% 82 3,20012351 =/a 5 1 % 91 3,20012352 5/a 6 1% 98 3,20012354 5/e 8 1% 120 3,20012356 5/e 10 1% 134 3,20012357 =/ 12 1% 153 3,20012358 % 1% 178 3,200

SPECIAL =/s h"L 1% 3,20012360 %12362 %

: 1 % 118 4,5001% 138 4,500

12364 % 8 1% 168 4,50012366 % 10 1 '/2 192 4,50012367 =/4 12 1% 216 4,50012368 =/4 15 1% 254 4,50012389 % 18 1 % 304 4,500

SPECIAL % AL 1% - 4,50012370 % I"/16 203 7,00012371 '/e

21"/'5 214 7,000

12373 % 8 I"/15 235 7,00012374 '/a IO I'%6 268 7,00012375 '/s 12 1'%6 302 7,000

SPECIAL '/a AL 11% _ 7,00012380 1 6 I'% 280 8,50012382 1 8 I'?& 335 8,50012384 1 IO 11% 365 8,50012385 1 12 1 ‘?4 6 430 8,50012386 1 15 I'%6 470 8,50012387

:18 1 % 550 8,500

SPECIAL AL 1% 8,50012390 1% 6 2 % 500 13,50012391 1% 8 2 % 580 13,50012393 1% 12 2%6 715 13,50012396 1%

::2% 1080 20,000

SPECIAL 1% 2 % 20,000SPECIAL 2 AL 3 % - 35,000AL = Any length shank.Available In metric threads and lag threads.*Also available In stainless steel and SIIOY.

Thrssd Shank I.D. Approx.Stock 01s. Length Eye wt. PerNO. A B C 1OOPO.

R12310 ‘/a 2 % 6R12312 ‘/4 3 % 7RI2314 ‘/4 ‘/2 8RI2315 ‘/4 ‘/2 11RI2316 '/4 6 '/2 13RI2319 =/M 2% =/ 11RI2321 %6 3 5% 13R12323 %6 : 5/s 15RI2325 %6 5/a 17R12326 % 6 S/a 20RI2330 3/a 2 % % 17R12331 J/a 3 % 21R12333 % 4 % 24R12334 % 4% % 25R12335 % 5 % 27RI2336 3/n 6 30RI2338 %

Y*8 Y4 36

RI2339 3/n IO % 40RI2340 '/2 3 % 1 40R12341 % : 1 41RI2343 1% 1 42RI2345 '/2 8 1 55R12347 '/z IO 1 67RI2348 % 1 75SPECIAL %

A:1 _

R12350 5/a 4 1% 82RI2351 5/a 5 1% 91RI2352 5/a 6 1 % 98RI2354 S/s 8 1% 120R12356 % 10 1 ?h 134RI2357 =?a 12RI2358 %

1% 153

:: 1 % 178SPECIAL =/s 1% -RI2360 % 4 1% 118R12362 % 6 1% 138RI2364 % 8 1% 168RI2366 3/, 1 'h 192RI2367 %

IO12 1;/; 216

R12368 =/4 15 1% 254R12369 % 18 1 % 304SPECIAL % AL 1% _R12370 7/a 1 “/I 6 203R12371 7/a : l"/M 214RI2373 % 8 I"/16 235RI2374 % 10 I"/'5 268RI2375 7/a 12 1"/16 302SPECIAL '/a AL l"/Is -RI2380 1 6 1 1% 6 280R12382 1 8 1% 335RI2384 1 IO I'% 365R12385 1 12 l'% 430RI2386 1 15 I'%. 470RI2387 1 18 1% 550SPECIAL 1 AL I'% -RI2390 1% 6 2 % 500RI2391 1 'A 8 2 % 580._RI2393 11/, 12 2 % 715R12396 1 % 12 2 % 1080RI2399 1 % 24 2% 1850SPECIAL 2 AL 3 % -

EDWARD W. DANIEL CO.

SWIVEL HOIST RINGS

Please include stock number and sizewhen ordering

E RADIUS

MATERIAL: 4140 Alloy SteelFINISH: Black OxideWASHER: Gold lriditeRANGE OF MOVEMENT: 360° Swivel,

180° Pivot

F DIAMETER

SAFETY FACTOR: 5 to 1. Ratedcapacity and thread torque isstamped on the washer.All parts are Magnetic Particle Inspected.Metric sizes available by request.

THREADLENGTH

A THREAD SIZE

Thread Thread WelghtStock Slse t%ViS

YggthTorque’ Each Rated’

NO. A B D E F 0 (Lb. Ft.) (Lb%) capacity16202 5/l&18 2.67 % 6 .75 .43 .38 1.84 7 .3 80016204 318.16 2.67 % 5 .75 .43 .38 1.84 12 .3 1,00016210 112.13 4.78 1 1.50 .88 .75 3.52 28 25 2,50016215 518.11 478 1 1.50 .88 .75 3.52 60 2.7 4,00016220 3/4-10 478 1 1.50 .88 .75 3.52 100 3.0 5,00016225 718-9 6.52 1 2.31 140 1.00 5.14 160 7.0 8,00016230 i-8 6.52 1 '/2 2.31 1.40 1.00 5.14 230 7.5 10,00016235 l-*14-7 8.73 1% 3.19 1.75 1.25 6.50 470 14.0 15,00016240 l-112-6 12.47 2 % et9 2.25 1.75 8.55 800 33.0 24,00016245 2.4'/2 12.47 3 % 4.19 2.25 1.75 8.55 800 36.0 30,000

'Rated load capacity based on specific thread torques, see product catalog for more information*It is recommended that these torques be used when installing hoist rings.

II-STRENGTHKING EYE

MATERIAL: Eye Nut - Carbon Steel,Alloy Stud - 4340 Alloy Steel

FINE%: Self-Colored _SAFETY FACTOR: 5 to 1

Thread Thread Appror. RatedStock Dip. Length wt. Per capacity

NO. 1 L A B C D E F 100 PCS. at 90016310 l-8 1% 1%6 1%6 2% 4 5 ?/a 260 9,00016315 l-114-7 1% 2% 2 2 4% 5% 1% 640 10,00016320 l-112-6 2 31/s 2x2 2% 5% 6% 1 % 900 15,000

I EDWARD W. DANIEL CO.

-

Shank center ttead HeadBuckeye Dbl. of Eye DI& Thickness A.ppML

Stock Forge Inches to End Inches Inches wt. ParNO. NO. A q C D 100 PCS.

Forged Rod Ends (1030)R-l 8004 22A ‘/a 1% ’ 732 =/ 6 3.5R-18006 - ‘/4 2% ‘/2 s/32 4.5R-18010 228 ‘/4 2 % s/32 4.5R-18012 22L ‘/4 AL ‘% s/32 4.5R-18020 - % 6 4 % % 6 13.0R-18022 23-A 5% 6 % 1% 2% 14.0R-l 8024 23-B % 5 ’ % 6 % 6 %4 15.0R-18034 24A 3/a 2 “/I6 % 6 5.0R-l 8036 24C % 4% ‘X6 % 6 6.0R-l 8038 24E 3/a 2% ‘%6 % 6 5.0R-l 8045 248 % 3’%6 1 ‘/I 6 5.0R-18048” - % 6 1% % 6 24.0SPECIAL” - % up to 12” “/I6 % 6R-18050O 2 4 L % AL “/Is % 5 6;R-18052O 25D % 6 4% ’ % 6 % 45.0

SPECIAL - - Any Length - % 5 -R-18054” 26 112D % 3 ‘% % 5 40.0R-18055O 26H ‘/2 7 ‘5% % 6 45.0R-l 8056O 26C ‘/2 2% 1% s/l 6 40.0R-18065O - % 6 ’ % 5 % 5 45.0R-18070’ - ‘/2 12 ‘% % 6 90.0R-18072” 26F ‘/2 3% 1 ‘/e % 40.0R-18075” - % 6 1 ‘/s % 36.0SPECIAL’= _SPECIAL0 _R-181000R-18102oR-18103OR-18104OR-18105OR-181100

27A27827C27E--

Up to 24” 1% % 6 -Up to 24” 1% % _

1% 7/a % 5 65.03% 1%6 1% 65.04% 1%6 “/I6 68.05% 1% “/Is 70.06 1% ’ ‘/I 5 73.0

12 1%6 1% 130.0SPECIAL” -R-18122’ 28AR-18124O 28CR-18125” 28DR-18130° -R-18135O -SPECIAL0 -R-18150’= -R-1815~5~ -

Up to 26” 1%6 “/I6 -

2 1% ‘/8 95.03% 156 ’ % 5 100.04% 1x6 1 % 6 105.06 1x6 ’ J/1 5 110.0

12 1x6 ‘% 200.0Up to 27” 1%6 ‘%6 -

6 l”/Ifi 1% 159.012 l”/W ‘%6 265.0

SPECIAL0 - ;/, up to 30” l”/l6 ’ % 6 -R-18170° - 1 6 2 1 213.0R-18175’= - 1 12 2 1 350.0SPECIAL” _- 1 Up to 30” 2 1

R-IA1940 - 1 ‘b 12 2% 1% 575.0SPECIAL0 - l,/, Up to 24” 2% 1 ‘/aSPECIAL0 - 1% Up to 24” 3 1%SPECIAL0 - 1% Up to 24” 3% t Y4 -

SPECIAL” - 2 Up to 24” 4 2Cold Headed Rod Ends (1008-1010)

R-IAolfi’ - ,213 2.875 ,535 ,281R-18017 - ,250 4.250 ,500 ,281R-18021’ - ,272 4.000 -750 ,313R-18031’ - ,328 1.500 ,745 ,438R-18041’ - ,328 3.000 ,745 438R-18051’ - ,328 4.500 ,745 ,438R-18061’ - ,444 1.750 938 ,563R-18066’ - ,444 6.000 ,938 ,563R-18076. - ,444 4.813 1.125 .500R-18086’ - ,444 3.000 ,938 ,563

‘Supplied with rolled thread diameter. AL=Any length shank

OAlso available in alloy, stainless steel and other materials.

ROD ENDSForged l Carbon Steel0 s Self-Colored

May be supplied either blank ormachined, BUT ARE STOCKED ASBLANK FORGINGS ONLY. Forainalengths (B) are standard, but oFhelengths can be made up special inquantity lots.

Rod Ends can be furnished toany length desired. In certain sizesand wherever practical we forge thelonger lengths solid, thus maximumstrength is assured. Threading andcross drilling can be modified tomeet customer requirements.

We are always interested in inquiriesfor Rod Ends of special sizes. Referto the left for the special sizes avail-able, many of which are carried instock, blank, and can be machinedto specification.l Shank lengths can vary +%” -0”.l Standard forging tolerances.l Supplied in fine thread and metric threads.l Available in 1008, 1030, 4140, 8620 steel

and stainless steel.

Self-colored will always be furnishedunless otherwise specified.INFORMATION REQUIRED(A) Shank diameter(B) Length center of eye to end(C) Head/Boss diameter(D) Head thickness(E) Size of drilled eye hole(F) Thread length with or without nuts.

EDWARD W. DANIEL CO. E.

ROD END BLANKSForged l Carbon SteelSelf Colored

MACHINED ROD ENDSForged l Carbon SteelSelf Colored

( I.D. Drilled only )

ALLOY ROD ENDSForged l 4140 AlloySelf Colored

EYE NUTSForged l 1030 Carbon Steel *Self-Colored/Hot Galvanized

E EDWARD W. DANIEL CO.

Stock GMC Approx.NO. Blank wt. PerA B C D 100 PCS.

R18012 117843 '/4 1 '/a %2 ’

R18023 117044 % 732R18030

1% 1x2 2117845

%

R18050 % 1 %117846 ?/I6%6 4x4 8

R180621%

117847%

'h% 12

1 % % 6 1 15R18106 140103 s/BR18126 119492 &

"iI6%

1%R18156

z:144263

'%67/a

1%

R181742 % 83

453507's/r 6 1%2

1 3 1% 2’/32 121

OrdnanceStock Plaln Finish Approx.

NO. Machined wt. PerA B C D E 100 PCS.16012 104046 ‘/4 1%18023

%2 1

104047732

%‘/4

6 1%18030 104048

1x2 78 %J/a

6 :1'/2 8

18050%6

117841 %4x4 3/s

618062 1% '/2 12104049 %'/2 1% %6%6 1 '/2 15

18106 140102 %18126 119491 % &

"/I6 1% % 32

18156 144262'%6

'/aI?& %

23/4 i:18174

'% 5221468

12%2 %1 3 1% w2 1 121

Stock Approx.NO. A wt. PerB C D 100 PCS.

RA18048 3/a 6 "/I6 % 6 24RA18065 % 6RA18070 '%6

'/2% 5

12RA18059 '% 6 % 6 :;% 18'% 6 % 5 130

RA18105 =/e 6RA18110 1 % 73

5/a 12"/I6

AA18117I?46 130

%“/I6

18 1%6 'X6 185RA18130 % 6RA18135 % 156 '%6 11012RAlI3137 1%5 200% 18 '%6

1%6 '% 6 315RA18150 7/a 6RA18155 l"/I, '% 6 159'h 12

l"/lS '%6 265RA18170 1 6 1RA18175

2131 12 E 1 350

ThreadStock DI8. Approx.

wt. PerNO. RatedT A B C D E F loo PCS. capacitySelf-Colored

16037 318.16 % =/e 1% 2% 22.016050 112-13

%%

2,7005/a 1 '/4

z

160622 %

518.11% 19.5 2,700

1% %16075

1 % 2% 60.0314.10

%1% % 1 % 2% i

5,000'/2 56.0 5,000

16087 718-9 l%S l'h 2 % 4:

110 174.116100 l-8

10,0001%6 l%, 2% 4 l/8 167.2 10,000

16125 l-114-7 27/a 216150 l-112-6 3'/8 2732 &*

4% 5 % 1% 625.0 29,4005% 6 % 1% 938.0 35,600

Hot Galvanized16037G 318.16 % 5/a 22.016050G

1%112-13 ;

2 % ?h%

2,7005/a 1% 2 % 19.5

16062G 518-11 1% %3/s

1 '/2 2%2,700

3 60.0160756

'/2314.10

5,0001% % 1% 2% 3 'I2 56.0 5,000

16087G 718-9 2 % 1% 1% 325.016100G

3 % 4% 1l-8 2 % 1%

10,0001% 3 % 4 % 1 315.0 10,000

16125G l-114-7 27/s 216150G

4 % 5 % 625.0l-112-6 3'/8

1 %2x2

29,4005 % 6 % 1% 938.0 35,600

l Also available In alloy.

Sire in Inches oen- not Body Approx.Thread Take- Colored Galvanlred Head Length wt. Per RatedDia. - T Up - D Stock No. Stock No. N L too PCS. CaDaCltV*I4 x 4 10604 10605 '/IS 47/a 11 5005116 x 4% 10606 10609 '/2 5% 20 000318 x 6 10612 10613 % 6 7 % 33 1,200112 x 3 10614 10615 3/b 4% 30 2,200112 x 6 10616 10617 3/b 7% 56 2,200112 x 9 10620 10621 % 1 0 % 70 2,200112 x 12 10624 10625 % 1 3 % 104 2,200518 x 3 10626 10627 '/8 4 % 50 3,500518 x 6 10626 10629 7/E 7 % 85 3,500518 x 9 10632 10633 % 1 0 % 106 3,500518 x 12 10636 10637 7/a 1 3 % 145 3,500314 x 6 10640 10641 1X6 8% 140 5,200314 x 9 10644 10645 1X5 11% 166 5,200314 x 12 10648 10649 1X5 1 4 % 210 5,200314 x 18 10652 10653 1% 2 0 % 320 5,200718 x 6 10654 10655 1% 8 % 160 7,200718 x 12 10656 10657 1% 1 4 % 272 7,200718 x 18 10660 10661 1 % 2 0 % 488 7,200

1 x 6 10664 10665 1% 8 % 218 10,0001 x 1 2 10668 10669 1 % 14% 358 10.0001 x 1 8 10672 10673 1% 20% 470 10,000l-118 x 6 10676 10677 l%e 9% 340 12.400l-114 x 6 10680 10681 1% 9% 324 15,200l-112 x 6 10684 10685 2 % 10% 590 21,400l-314 x 6 10688 10689 2 % 10% 650 27,6002 x 6 10692 10693 2"/.. 1 1% 1280 34.500

Size In Inches AverageOverall

Stub Take-Stock Dia.

"0'Nead z::::

Appror.wt. Per Rated

NO. D N L 100 PCS. Capaclt’y10504 114 x 4 % 5 9 21 50010508 5116 x 4% ‘/2 11 40 800

*lo512 318 x 6 % 6 13 70 1,20010514 112 x 3 % 11 90 2,200

*lo516 112 x 6 % 14 125 2,20010520 112 x 9 J/4 17 152 2,20010524 112 x 12 % 20 195 2,20010526 518 x 3 7/s 12 145 3,500

*lo528 518 x 6 7/s 15 195 3,50010532 SIB x 9 7/s 18 245 3,50010536 518 x 12 % 21 300 3,500

*10540 314 x 6 1X5 16 320 5,20010544 314 x 9 1X5 19 390 5,20010548 314 x 12 1X6 22 440 5,20010552 314 x 16 1%6 28 616 5,20010554 718 x 6 1%6 17 430 7,20010556 718 x 12 1%6 23 570 7,20010560 718 x 18 1%6 29 906 7,2001 0 5 6 4 1 x 6 1 % 18 578 10,00010568 1 x 12 1% 24 804 10,00010572 1 x 18 1 % 30 1020 10,00010576 l-118 x 6 1%6 19 820 12,40010580 l-114 x 6 1 % 19 930 15,20010584 l-112 x 6 2 % 20 1530 21.400

Safety factor 5 to 1.“Hot galvanized or zinc plated upon request.

TURNBUCKLEBODIESForged l Carbon Steel *Self-Colored/Hot Galvanized

STUB ENDTURNBUCKLESForged l Carbon Steel +Self-Colored l *

*Available in stainless steel.


EYE&EYEForged l Carbon Steel”Self-Colored/Hot Galvanized

HOOK & EYEForged l Carbon SteelSelf-Colored/Hot Galvanized

HOOK & HOOKForged l Carbon SteelSelf-Colored/Hot Galvanized

Sire In InchesThread TakeDI& UP114' x 45H6 x 4%316 x 6112 x 6112 x 9l/2 x 12518 x 65111 x 9516 x 12

self- Hot Appmx.Colored Galvanized wt. PerStock No. Stock No. 100 PCS.10004 10704 2510008 10708 4410012 10712 7910016 10716 15110020 10720 18110024 10724 22010028 10728 25010032 10732 30010036 10736 36010040 10740 390314 x 6

314 x 9 10044 10744 460314 x 12 10048 10748 530314 x 18 10052 10752 720716 x 12 10056 10756 760718 x 18 10060 10760 1060 .,

1 x 6 10064 10764 7501 x 12 10068 10768 10001 x 16 10072 10772 1222

114' x 4 10104 10804 255/16 x 4 % 10108 10806 443/8 x 6 10112 10812 79112 x 6 10116 10816 151112 x 9 10120 10820 181112 x 12 10124 10824 220516 x 6 10128 10826 250516 x 9 10132 10832 300516 x 12 10136 10836 360314 x 6 10140 10840 3903/4 x 9 10144 10844 4603/4 x 12 10148 10848 530314 x 18 10152 10852 720718 x 12 10156 10856 760718 x 18 10160 10860 1060

1 x 6 10164 10864 7501 x 12 10168 10868 10001 x 18 10172 10672 1222

114' x 4 10204 10904 25S/l6 x 4 % 10208 10906 443/a x 6 10212 10912 79112 x : 10216 10916 151112 x 10220 10920 161112 x 12 10224 10924 220516 x 6 10228 10928 250516 x 9 10232 10932 300518 x 12 10236 10936 360314 x 6 10240 10940 390314 x 9 10244 10944 460314 x 12 10248 10948 530314 x 18 10252 10952 7207/8 x 12 10256 10956 7607/8 x 18

1 x 61 x 121 x 18

'114" Size only electro-galvanized.

10260 10960 106010264 10964 75010268 10968 100010272 10972 1222

E. EDWARD W. DANIEL CO.

notThread DIP. Take-UD

Approx.wt. Per100 PCS.

11004 i14= x 4 2611008 5116 x 4% 4511012 318 x 6 7811016 112 x 6 15111020 112 x 9 17911024 112 x 12 22011028 518 x 6 25311032 518 x 9 29911038 518 x 12 36811040 314 x 6 41411044 314 x 9 45811048 314 x 12 53211052 314 Y IA 699

Galvanized is tapped oversize.

JAW & EYEForged l Carbon Steel l Hot Galvanized

?

11056 718 x 12 80511060 718 x 18 105311064 1 x 6 80511068 1 x 12 111311072 1 x 18 1306

11104 l/4’ x 4 2811108 5H6 x 4% 4911112 318 x 6 8511116 112 x 6 18411120 112 x 9 19511124 112 x 12 24011128 518 x 6 27511132 518 x 9 32511136 518 x 12 40011140 314 x 8 45011144 314 x 9 49811148 314 x 12 57811152 314 x 18 76011156 7/B x 12 87511160 7/B x 18 114511164 1 x 6 92011168 1 x 12 121011172 1 x 18 1420

‘l/4” size only electto-galvanized.

TURNBUCKLE NOTESl Hot galvanized will be furnished unless otherwise specified.l Other sizes and detailed dimensions can be supplied upon request. When ordering,

please specify thread diameter, length of take-up, figure number, and finish.l JAW END FITTINGS: All sizes furnished with a Cotter Pin and 1038-1045

Steel Rivet.l Bolts and nuts can be furnished at additional charge.l Lock washers and nuts per each end add 10% per end.l Tapped threads are self-colored.l Safety factor 5 to 1.

JAW & JAWForged l Carbon Steel l Hot Galvanized


EDWARD W. DANIEL CD.DIAMOND D BRAND HARDWARE...ASDURCEYDU CAN DEPENDDN

EDWARD W. DANIEL CO. m1

OVAL EYE &OVAL EYEForged l Carbon Steel l Hot Galvanized,

I IGalvanized is tapped oversize.

HOOK &OVAL EYEForged l Carbon Steel l Hot Galvanized


JAW &OVAL EYEForged l Carbon Steel l Hot Galvanized


not She In Inches Approx.Galvanhed wt. Perstock no. Thread Dia. Take-Up 1DDPCS.

11704 1149 x 4 3111706 5/16 x 4 % 4511712 316 x 6 7711716 112 x 6 14011720 112 x 9 18011724 112 x 12 22011726 516 x 6 23511732 518 x 9 28011736 518 x 12 34011740 314 x 6 38011744 314 x 9 46011746 314 x 12 52011752 314 x 16 70011756 7/8 x 12 75011760 718 x 18 95011764 1 x 6 80011766 1 x 12 106011772 1 x 16 1300

11804 114' x 4 3111806 5116 x 4 % 4511812 318 x 6 7911616 112 x 6 15011620 112 x 9 16611624 112 x 12 22411626 518 x 6 22511632 518 x 9 29611636 518 x 12 35511840 314 x 6 39011644 314 x 9 47011848 314 x 12 53011652 314 x 16 716

-11656 718 x 12 76011660 718 x 16 95011664 1 x 6 80011666 1 x 12 107011672 1 x 18 1300

11204 114' x 4 3211206 5116 x 4 % 4511212 318 x 6 8011216 112 x 6 15411220 112 x 9 16511224 112 x 12 23011228 518 x 6 26011232 518 x 9 30711236 518 x 12 37011240 314 x 6 40111244 314 x 9 49011246 314 x 12 55011252 314 x 16 72011256 718 x 12 80011260 718 x 16 97611264 1 x 6 65011268 1 x 12 112511272 1 x 18 1360

Note: Tapped threads are self-colored'l/4" size only electro-galvanized.


Dimensions in inches l Weights in poundsPlease include stock number and size when ordering

Self-Colored

Stock No.10502

s,ze in lnchelThread Take-DIP.-D UP-0l/4 x 4

ThreadRH

r4pprc.x.wt. Per100 PCS.

5

Ratedcapacity

50010503 114 x 4 LH 5 50010506 5/16 x 4’/2 RH 10 80010507 5116 x 4% LH 10 60010510 318 x 6 RH 19 1,20010511 3/8 x 6 LH 19 1,20010513 112 x 3 R H 30 2,20010515 112 x 3 LH 30 2,20010517 112 x 6 R H 35 2,20010516 112 x 6 LH 35 2,20010519 112 x 9 R H 41 2,20010521 112 x 9 LH 41 2,20010522 112 x 12 R H 46 2,20010523 112 x 12 LH 46 2,20010529 5/8 x 6 R H 55 3,50010530 518 x 6 LH 55 3,50010533 518 x 9 RH 69 3,50010534 518 x 9 LH 69 3,50010537 518 x 12 RH 78 3,50010536 518 x 12 LH 76 3,50010541 3/4 x 6 RH 90 5,20010542 3/4 x 6 LH 90 5,20010545 3/4 x 9 RH 102 5,20010546 3/4 x 9 LH 102 5,20010547 314 x 12 RH 115 5,20010549 314 x 12 LH 115 5,20010550 314 x 16 RH 148 5,20010551 3/4 x 16 LH 146 5,20010553 718 x 6 RH 135 7,20010555 7/8 x 6 LH 135 7,20010557 718 x 12 RH 149 7,20010556 718 x 12 LH 149 7,20010561 718 x 16 RH 210 7,20010562 7/e x 16 LH 210 7,20010565 1 x 6 RH 160 10,00010566 1 x 6 LH 160 10,00010569 1 x 12 R H 223 10,00010570 1 x 12 LH 223 10,00010573 1 x 16 RH 275 10,00010574 1 x 18 LH 275 10,00010577 l-118 x 6 R H 240 12,40010578 l-118 x 6 LH 240 12,400,"SF?l l-114 x 6 R H 303 15,200.___10562 l-114 x 6 LH 303 15,20010565 l-112 x 6 RH 470 21,40010586 1.112 x 6 LH 470 21,400

Safety factor 5 to 1

STUB ENDSForged l Carbon Steel

EDWARD W. DANIEL CO.DIAMOND D BRAND HARDWARE...A SOURCE YOU CAN DEPEND ON



JAWSForged l Carbon Steel

not Size in Inches Approx.Galvanized Thread Take. wt. Per RatedStock Go. Dia.-A Up G C 0 E F G Thread 100 PCS. Capacity11105 114 x 4 S/s % 6 %2 % 5 =/8 '/4 RH 9 50011106 114 x 4 % % 6 %2 % 5 % '/a LH 9 500

11109 5H6 x 4y2 % '12 '/a '/2 '%6 '/4 RH 15 60011110 St16 x 4% 314 '12 '19 '/2 ‘%6 ‘h LH 15 80011113 3/e x 6 '%6 % 6 %6 %6 '% 5 5/16 R H 26 1,20011114 3/a x 6 '% =/I 5 VI6 %6 '3/l 6 %E LH 26 1,200

112x3 1 % % % 1 x15 - - _1 1 1 1 7 1 1 2 x 6 1 Ye % % 1 %6 R H 54 2,1001 1 1 1 6 1 1 2 x 6 1 % YE 3/a 1 y,s L H 54 2.1001 1 1 2 1 1 1 2 x 9 1 % % % 1 56 RH 63 2,1001 1 1 2 2 1 1 2 x 9 1 5/s % % 1 %s LH 63 2,10011125 112 x 12 1 5/s % % 1 '/,s R H 68 2,10011126 112 x 12 1 5/a 3/s % 1 '/IS LH 68 2,f0011129 518 x 6 1% % %6 1 1% 'h RH 95 3,20011130 518 x 6 15/S % %6 1 1%6 '/z LH 95 3,20011133 518 x 9 1%6 % %5 1 1% '/z RH 109 3,20011134 518 x 9 1 % 6 % %6 1 1% '/z LH 109 3,20011137 5/B x 12 l%, % '/I6 1 1% 'h RH 126 3,20011136 5/8 x 12 I%6 % %6 1 1% % LH 126 3,20011141 3/4 x 6 1% 'VI16 %6 I%16 1% % RH 155 5,00011142 3/4 x 6 1 % 'VI16 %6 1%6 1% % LH 155 5,00011145 3/4 x 9 1 '/2 '%16 % 6 1%6 1% % RH 156 5,00011146 3/4 x 9 1 '/2 q%6 'A16 13/E 1% % LH 156 5,00011149 314 x 12 1 '/2 1%6 '/I6 13/e 1% % RH 184 5,00011150 314 x 12 1% 1%6 '/I6 1%6 Is/s ?'a LH 184 5,00011153 314 x 18 1 % '% 716 I%6 1% YE RH 220 5,00011154 314 x 16 I'/2 1%6 %6 1% 1% % LH 220 5,000

718 x 6 1% I%6 % 1% 1% Y4 -

11157 7/a x 12 1% 1%6 '/2 1% 1% % RH 302 7,00011156 718 x 12 1% 1 % 'h 1% 1% % LH 302 7,00011161 7/8 x 18 1% I’/16 72 1% 1% % RH 329 7,00011162 7/E x 18 1 % I%6 '/2 1% 1% % LH 329 7,00011165 1 x6 2 I%16 % 1% 2 % 1 RH 351 10,00011166 1 x6 2 1%6 % 1% 2 % 1 LH 351 10,00011169 1 x12 2 13/K % 1% 2 % 1 RH 426 10,00011170 1 x12 2 1%6 5/s 1% 2 % 1 LH 426 10,00011173 1 x16 2 13/E 5/s 1% 2 % 1 RH 475 10,00011174 1 x18 2 1%6 % 1% 2 % 1 LH 475 10,000

Safety factor 5 to 1.

EDWARD W. DANIEL CO.DIAMOND D BRAND HARDWARE...ASDURCEYDU CANDEPENDDN

-

II EDWARD W. DANIEL CO.


HOI Size in Inches Approx.Galvanized Thread Take- wt. Per Rated

- Stock No. Dia.-A UP G c D E Thread 100 PCS. Capacity11705 114 x 4 IV32 %2 2%2 12%2 RH 10 50011706 114 x 4 1 %2 7132 2%2 1*%2 LH 10 50011709 S/l6 x 4% % 6 %2 1%6 WI6 RH 13 60011710 5H6 x 4% % 6 g/32 1 %6 ?/I 6 LH 13 60011713 318 x 6 ‘%2 I’/32 1% 2%~ RH 23 1,20011714 3/8 x 6 ‘%2 “A2 1 ‘/a Wx LH 23 1,200

_ 112 x 3 2%2 % 6 1x6 3x2 - -

11717 112 x 6 23/32 %6 156 3x2 RH 42 2,20011718 112 x 6 '%2 %6 1x6 3%2 LH 42 2,20011721 112 x 9 2K2 ‘A5 1%~ 3%~ RH 55 2,20011722 112 x 9 v32 ?/I16 1%6 3%2 LH 55 2,20011725 112 x 12 2%2 %6 156 3%2 RH 58 2,20011726 112 x 12 v32 %6 I%6 3x2 LH 58 2,20011729 S/8 x 6 '/a % 1% 3 % RH 75 3,50011730 518 x 6 % '/2 t 3/s 37/a LH 75 3,50011733 518 x 9 '10 '/2 t % 37/8 RH 86 3,50011734 518 x 9 l/8 ‘/2 1% 37/a LH 86 3,50011737 518 x 12 l/8 % 1 v4 3% RH 98 3,50011738 5/8 x 12 '/a '/2 1% 3% LH 98 3,50011741 3/4 x 6 1 % 2% 4'/16 RH 120 5,20011742 3/4 x 6 1 % 2 % 4"/,6 LH 120 5,20011745 3/4 x 9 1 % 2'/8 4"/,6 RH 137 5.20011746 3/4 x 9 1 % 21/E 41%~ LH 137 5,20011749 314 x 1 2 1 Ye 2'h 4"/,6 RH 155 5,20011750 314 x 1 2 1 5/a 21/a 41% LH 155 5,20011753 3/4 x 1 8 1 5/a 21/a 41%~ RH 190 5,20011754 3/4 x 1 8 1 =/8 21/a 4'1/,6 LH 190 5,200

7/8 x 6 t 'h % 2 % 5$/q _11757 718 x 12 t '/a % 2?h 5 % RH 239 7,20011758 7/8 x 12 1 'h % 23/8 5 % LH 239 7,20011761 7/8 x 18 1% % 2 % 5% RH 231 7,20011762 718 x 18 1% % 2?& 51/q LH 231 7,20011765 1 x 6 1x6 7/a 3 63/8 RH 291 10,00011766 1 x 6 1x6 '/a 3 6% LH 291 10,00011769 1 x 12 1 % 6 7% 3 6% RH 351 10,00011770 1 x 12 I%6 7/s 3 6% LH 351 10,00011773 1 x 16 1 % 6 '/a 3 6% RH 415 10.00011774 1 x 18 1x5 '/a 3 6 % LH 415 10,000

OVAL EYEForged l Carbon Steel

Safety factor 5 to 1.

EDWARD W. DANIEL CO.DIAMOND D BRAND HARDWARE...ASOURCEYOU CAN DEPENDON

EDWARD W. DANIEL CO. m’

Please include stock number and size when ordering

HOOKSForged l Carbon Steel

Size in Inches Sell- Hot Appm.Thread Take- Colored Galvanized WI. Per RatedDia.-A up B c 0 Thread Stock No. Stock No. 100 PCS. Capacity114 x 4 3/s '/a %2 R H 10205 10905 7 300l/4 x 4 % '/4 %2 LH 10206 10906 7 3005H6 x 4% % % 6 ’ %2 R H 10209 10909 12 5005116 x 4 % % % 5 ’ %2 LH 10210 10910 12 500316 x 6 '%.

--J/a ’ 732 RH 10213 10913 23 700

316 x 6 '%2 3/a '%z LH 10214 10914 23 700112 x 3 '%6 '/2 2x2 - _ - -

112 x 6 1% % %z RH 10217 10917 48 1,040112 x 6 *VI6 % VW LH 10216 10918 46 1,040l/2 x 9 1 % 6 ‘/2 %z RH 10221 10921 56 1,040112 x 9 ’ % 6 % Vsz LH 10222 10922 56 1,040112 x 12 ’ % 6 ‘12 %z RH 10225 10925 56 1,040112 x 12 ’ % 6 ‘/2 %z LH 10226 10926 56 1,040516 x 6 7/e 5/s '%e R H 10229 10929 83 1,600S/8 x 6 7/a 5/s I%6 LH 10230 10930 63 1,6005/8 x 9 7/s s/a I=/16 R H 10233 10933 96 1,600518 x 9 ?/a 5/s ’ % 6 LH 10234 10934 96 1,600518 x 12 'h 5/a 'Se RH 10237 10937 108 1,600518 x 12 7/a 5/a 'Se LH 10238 10938 108 1,600314 x 6 1 % 3'/32 RH 10241 10941 125 2,000314 x 6 1 % %z LH 10242 10942 125 2,0003 1 4 x 9 1 314 %s RH 10245 10945 137 2,0003/4 x 9 1 % %z LH 10246 10946 137 2,0003/4 x 12 1 % 3'hz RH 10249 10949 160 2,000314 x 12 1 % 3%2 LH 10250 10950 160 2,000314 x 18 1 % 3'/32 RH 10253 10953 200 2,000314 x 18 1 % 3'/32 LH 10254 10954 200 2,000718 x 6 1 '/a 'h 11/4 - - _ _ _718 x 12 1 '/0 '/a 1% RH 10257 10957 244 2,400 -7/8 x 12 11% '/a 1'/4 LH 10258 10958 244 2,4007/8 x 18 l'h 7/8 1'/4 RH 10261 10961 286 2,400718 x 18 1'1s '/a 1% LH 10262 10962 266 2,400

1 x 6 I%6 1 11/a RH 10265 10965 266 2 , 9 0 01 x 6 1%6 1 II/4 LH 10266 10966 266 2,9001 x 12 1% 1 I'/4 R H 10269 10969 321 2,9001 x 12 1% t 11/b LH 10270 10970 321 2,9001 x 18 1%5 1 1'/4 R H 10273 10973 376 2,9001 x 18 1%. 1 I'L LH 10274 10974 376 2.900

Safety factor 5 to 1

E D W A R D W . D A N I E L C O .DIAMOND 0 BRAND HARDWARE...ASOURCEYOU CAN DEPENDON


Dimensions in inches l Weigbts in poundsPlease include stock number and size when ordering

Size in InchesThread Take-Dia.-A up B c114 x 4 ‘/, ‘L

sen- HOI Appmx.Thread Calmed Galvanized wt. Per RatedLength Thread Siock No. Stock No. 100 PCS. Capacity

3 RH 10005 10705 7 500‘- -114 x 4 ‘/2 ‘/4 3 LH 10006 10706 7 500

5/l 6 x 4’/, % % R 3 RH 10009 10709 12 800S/l6 x 4’/; 5/, 51116 3 LH 10010 10710 12 800318 x 6 % 318 4 RH 10013 10713 23 1,200318 x 6 % % 4 LH 10014 10714 23 1.200112 x 3 1 % 6 _ _ -112 x 6 1 % 6 4 RH 10017 10717 4 6 2,100112 x 6 1 ‘/I 6 4 LH 10018 10718 46 2,100112 x 9 1 % 6 6% RH 10021 10721 56 2,100112 x 9 1 % 5 6% LH 10022 10722 56 2,100112 x12 1 % 6 7% RH 10025 10725 58 2,100112 x12 1 % 6 73/a LH 10026 10726 58 2,1005/6 x 6 1% % 6 5 RH 10029 10729 83 3,2005/8 x 6 1% %6 5 LH 10030 10730 83 3,200518 x 9 1 % % c 6 % RH 10033 10733 96 3.200,”518 x 9 1% %6 69; LH 10034 10734 96 3.2005/8 xl2 1% % 6 8 RH 10037 10737 108 3,200518 xl2 1% % 8 LH 10038 10738 108 3,200314 x 6 1 % 2%2 5th RH 10041 10741 125 5,0003/4 x 6 1 % 2’/32 5% LH 10042 10742 125 5,000314 x 9 1 'A 2'h. 6 % RH 10045 10745 137 5.000ii4314

x 9 ,1/; ‘“_2x2 65/, LH 10048 10746 137x12 1% 2% 8 RH 10049 10749 160

5,0005,000

ROUND EYESForged l Carbon Steel

314 x12 11/i vi; 8 LH 10050 10750 160 5,0003/4 xl8 1 '/2 2x2 111/s RH 10053 10753 200 5,000314 xl8 1 '/2 2’/32 ill/, LH 10054 10754 200 5,000718 x 6 I'%6 % _ _ -7/8 x12 1'%6 3/4 9 RH 10057 10757 244 7,0007/8 x12 11%6 ?A 9 LH 10058 10758 244 7,0007/8 x18 l"/,, % 12 RH 10061 10761 286 7,0007/8 xl8 1 "/I6 % 12 LH 10062 10762 286 7,000

1 x 6 1'%6 % 55/s RH 10065 10765 266 10,0001 x 6 1’s 6 ‘h 55/8 LH 10066 10766 266 10,0001 x12 1'S?, 7/a 8% RH 10069 10769 321 10,0001 x12 1'3/,16 % 8'/2 LH 10070 10770 321 10,0001 xl8 1'S?, % ll'/, RH 10073 10773 376 10,0001 xl8 1 'SE 7/s II'/, LH 10074 10774 376 10,000

Safety factor of 5 to 1

EDWARD W. DANIEL CO.DIAMOND 0 BRAND HARDWARE...ASOURCEYOU CAN OEPENOON


SCREW PINForged l Carbon SteelSelf-Colored/Hot Galvanized

l Safe Working Load permanently shown on each shackle.l Shackles can be furnished proof tested with certificates per requirements

of A.B.S. and/or I.C.G.B. Charges for proof testing and certification availableon reauest.

:rew pin anchor shackles meet Federalxxification RR-C-271b, Type IV Class 1

SCREW PINAMERICAN-MADEForged l Carbon SteelHot Galvanized

self- notCOlONd InSide Width Rated

Nominal GalManlZed Inside Diameter Appror.Stock Shackle Stock

Th ltgPin It gOwPin wt. Per

C\$$tY

NO. Size NO. c 0 100 PCS. Tons- 3116’ 19100 7/e % "A6 % 6.5 %

190051901019015190201902519030190351904019045190501905519060

114 19105 1%5116 19110 1x2318 19115 1567116 19120 l”h112 19125 1%518 19130 2%314 19135 2’s710 19140 3 %

1 19145 3 %1.118 19150 4 %l-114 19155 4'%6l-318 19160 5%

% 25/32 % 5 11.5 %2x2 2/a 18.4 %1x2 % 5 31.5 11%2 % 44.6 1%1%6 % 74.5 211%6 % 136.4 3 %2 7/a 213.5 4 %w32 1 345.5 6 %21% 1% 500.0 8 %229/2 1% 709.0 9 %3'/4 1% 991.0 12.'3'h 1 '/? 1328.0 13%

“-19065 l - 112 19165 5% 23/, 3% 1% 1690.0 17’-

‘Not covered by RR 271 D.

not Inside Wldth RatedG&gvy;rd i;,m:~;l lnslde Dlsmeter Appror.

Length At Pln At Bow Pill wt. Per CU&Y

no. SlZ.2 A B C D 1 DO PCS. Tons19405 114 1% % 2%2 % 6 11.5 %19410 5H6 1x2 ’ %2 2%2 % 18.4 %19415 318 156 2x2 1 ‘/x2 % 6 31.5 119420 7116 1'%6 2%2 I%2 ‘/2 44.6 1 ‘/219425 112 1% ‘%6 1%6 5/s 74.5 219430 518 2 % 1% 1’%6 % 136.4 3 %19435 314 2'%6 1% 2 '/a 213.5 4 %19440 710 3% 156 w32 1 345.5 6 %19445 1 3 % 1'%6 2"/Is 1% 500.0 8%

ROUND PINForged l Carbon SteelSelf-Colored/Hot Galvanized

Self- NotColored Nominal Galvanized Inside%Zk

Shackle Stock LengthSire NO. A

xmd pin anchor shackles meet Federal)ecification RR-C-271b, Type IV Class 4

ROUND PINAMERICAN MADEForged l Carbon SteelHot Galvanized

El EDWARD W. DANIEL CO.

19205 114 19305 1% '/2 2%2 % 5 11.5 ‘/2

19210 5116 19310 1x2 ’ %2 2%2 2/s 18.4 %19215 3/8 19315 1x6 2x2 1x2 % 6 31.5 119225 112 19325 1 % '% 1%6 % 74.5 219230 518 19330 2 % 1YI.X l"/M % 136.4 3%19235 3/4 19335 2'S 1% 2 7/a 213.5 4 %

not Inslde Width RatedGalvanized Nominal lnslde Diameter

Stock ShackleLe??h

Approx.At Pin At Bow Pill wt. Per Caz*yNO. SIZEZ B C D too PCS. Tons

19605 114 1% 'I2 2%2 % 6 11.5 '/219610 5116 1x2 1x2 2x2 % 18.4 %19615 3/E 1x5 2x2 1’132 % 5 31.5 119625 112 i'/n '3/n 1%. % 74.5 219630 518 2% G, 136.4 3 %19635 314 2'%6 718 213.5 43/4

FORGED WIRE ROPE CLIPSForged l Carbon Steel l Hot Galvanized

Min. No. Min.

%”Size for

Otmenstons “‘%:pRope Dia. A B C D E F G N Strength

tztt: $!;;;

18500’ ‘J/B ‘/2 1 % 6 % ‘S/l 5 %2 2%2 % 5 2 % 6.018505 % 6 ‘%2 1%2 % v32 1% ‘/4 ‘%e % 2 1% 9.018510 ‘/4 “/I6 1%6 7/a 1x2 1% % 6 ?‘/8 “/I6 2 1% 18.018515 s/l 6 7/8 l”/l6 1 1% 12x2 j/B 1% ?h 2 1% 30.018520 3/a 1 1% % 1% 2 % 6 1% ‘/s 2 2% 44.518530 ‘/2 l%s 2% 1 ‘/I 5 12x2 WI6 ‘/2 1’?46 1%2 3 3 71.618540 5/a 1% 2% 1%5 2 % 2% 9/w 2%6 1% 3 3% 100.010545 % 1% 2% 1% WI6 3% 5/a 2 % 5 1’732 4 4’/2 140.018550 7/a 1% 3%6 17/e 3% 37/a % 2716 1% 4 5% 200.018555 1 1% 3% 2% 3% 4% % 21% 1% 5 6 245.018560 1 ‘/a 2%6 31% 2?& 370 4% 3/4 3 2 6 6% 285.018565 1% 2?& 4% 23/B 4% 5% ‘18 3% 2732 6 7% 415.010570 1’/2 2’9/32 4% 27/w, 5 51/ '/a 3 % c/32 7 9 543.0

‘l/8 only is supplied with regular hex nut and zmc plated U-bolt.

1 SEE PAGE 19 FOR PROPER WIRE ROPE CLIP USAGE 1

StockNO.

209002090520910209152092020925209302093520940209452095020955209602096570970

Rope Sirel/16’116’3116114511631671161126116518314716

11.118l-114

InsideLength“i&t

2%2

2%2

1%1%21 %1%1%1%2%2%2%31/a3%3%41/A

Min. no.of Clipsfor Mar.Strength

2-42-42-42-42-42-43-43-43-43-44-54-54-56-86-8


3.04.56.5

12.012.019.021.837.046.054.080.0

116.0137.0267.0328.0

‘NOTE: Not covered by FF-C-450 Type I, Class 2USE CLIPS PROPERLY FOR MAXIMUM EFFICIENCY1 “Bolt ShO”ld bear on dead end Of rape2 “SC? recommended number 01 CIIPS, depending on Safety req”lrement3 spacmg between c,,ps Should be 6 t,mes the rope diameter4 N”,S Should be re-tlghfened aner lnltlal lOad

1 SEE PAGE 19 FOR PROPER WIRE ROPE CLIP USAGE 1

ADWOX.wi. Pertoo PCS.

7.0Stock No. Safe-Line No. Rope Size

18651 X6-1051 11818653 XB-1053 3116 16.018654 XB-1054 114 25.018655 XB-1055 5116 50.018656 XB-1056 318 75 018662 XB-1062 314 500.0

c I- -F-e--B-- ---c --I

- All clips are supplied wth cold-forged double chamfered, heavyhex, UNC-26 nuts’

- Meet Federal SpecificationFF-C-450~ Type I, Class 1

- Base, U-bolt and nuts are hot-dipgalvanized in accordance withASTM Speciflcatlon A-153.’

- Forged wire rope clips are notdeslgned for load carrying pur-poses therefore, working loadlimits have not been established

MALLEABLEWIRE ROPE CLIPSCarbon Steel l Zinc Plated

l All regular hex nuts.l Clips meets Federal Specification

FF-C-450, Type I, Class 2l Bulk pack

SAFE-LINE CLAMPSForged - 1030 Carbon SteelSelf ColoredI

Provides an efficiency of over 90% of rated wire-rope strength - Accommodates 6x19(I.W.R.C.) or 7x19 right-regular-lay wire rope - Easy-to-use 3 piece assembly - can befield assembled faster than U-bolt clips, yet offers nearly same smooth configuration asa waged fitting - Encloses potentially hazardous wire ends Meets or exceeds allrequirements for military standard MS-16843; and conforms to Federal SpecificationFF-C-450.


REGULAR TYPETHIMBLESCarbon Steel l Hot Galvanized

Recommended for light duty service.Regular type meets Federal SpeclflcatlonFF-T-276b, Type II.

HEAVY WIREROPE THIMBLESCarbon Steel l Hot Galvanized

1 1

r---.‘.rimJp I’ P “:;

,’,’_/’

Stock sizeNO. Rr,pe Dia.40400’ ‘/a’40405 %.

Approx.LengthOverall1%1%

Approx.wt. Per100 PCS.1.42.2

40410 I/,- 1 % ’ ‘A 6 3.640415 % 6 2 ’ ‘/l6 6.440420 % 2% 2% 10.040425 % 6 2% I%6 12.640430 ‘/? 3 1 ‘/a 20.5,_40435 5/n 3% li/, 30.440440 3/, 4% 1% 46.040445 78 4% 1% 75.0zul45rl 1 6 2’/a 92 0

‘l/e” German B-DIN specification.Open pattern available upon application.

sire Max. Appror.Stock Rope Pin Dia. wt. Par

No. DI& B c F L P W too PCS.40300 ‘/4 I’%6 ‘/B % 6 2’/4 ‘-se 1 ‘h 9.040305 % 6 2 I%6 ‘%2 2% 1 1 % 13.540310 % 2% 1 ‘h v32 2% 1%6 2 26.040315 % 6 2% 1% % 3x6 1% 2% 31.040320 % 2% 1 ‘/z 7/a 33/q 1%6 27/B 43.040325 % 6 2% 1 ‘/z ’ =/I 6 3% 1%6 2% 46.040330 5/a 3% 13/n t %2 4%6 1% 3 76.040335 % 3% 2 1% 5 1 Ye 35/4 142.540340 ‘/8 4% 21/q I%6 5q%6 2% 4% 189.040345 1 4% 2’%6 1% 6%6 2% 4’%6 280.040350 1%-l% 5% 2’716 1 ‘/s 7% 2% 5716 402.0

A heavy thimble with deep score, made from heavy gauge steel. Designed to wlthstandthe crushing strains imposed by severe loads. Hot-dip galvanized in accordance withASTM Specification A 153 for maximum corrosion protection. All sizes meet or exceedFederal Specification FF-T-276b for Type Ill thimbles.

HDW To Attach Drop Forged Wire Rope ClipsThe right way to attach wire rope clips is illustrated at left. The base or saddle shouldbear on the live end of the rope - U-bolt on the short or dead end. Staggering orreversing the clips does NOT give additional holding power.1. ATTACH FIRST CLIP one base width from dead end of rope. Tighten nuts securely.2. ATTACH SECOND CLIP as close to loop as possible. Tighten nuts firmly but not

completely tight.3. ATTACH ALL OTHER CLIPS (if required) equally spaced between the first two.

Tighten nuts firmly.

CAUTIONApply the initial load to the rope. Alternately and uniformly retighten a// nuts securely, tocompensate for any reduction of rope diameter. Inspect and periodically retlghten. Thenumber of clips shown should be used for 6x19 or 6x37 class, fiber core or IWRC, IPSor XIPS, right regular or long lay Wire Rope, and 6x19 or 8x7 class, fiber core, IPS orXIPS, Wire Rope.For 6x19 Scale construction or similar large outer wire constructions, add one extra clipfor sizes 1” and larger. Where service conditions are unusually severe, or for otherclasses of rope not mentioned above, add one additional clip.Drop Forged Wire Rope Clips, when properly applied to new rope will develop highefficiencies (approximately 80%) based upon the catalog breaking strength of the wirerope. Failure to follow the above instructions will cause a reduction in efficiency.


StockNO.Wmble Bright Finish

197051971019715

Size Of WI. Per RatedChain 100 PCS. Capachy

114 29.0 1,2505116 43.0 1,900318 83.0 2,650

19720 7116 124.0 3,50019725 112 205.0 4,50019730 516 341 .o 6,90019735 314 530.0 9,750

Heat ‘ReatedlZlnc Plated

19805 114 29.0 2,60019810 5116 43.0 3.90019815 316 83.0 5;40019820 7116 124.0 7,20019825 112 205.0 9,20019830 518 341 .o 14,00019835 314 530.0 19.900

lbmble Bright Finish1990519910

II4 30.0 1,2505116 52 0 1 9””

19915 31819920 7116

is.0140.0

2,6503.500

19925 112 200.0 4:50019930 516 360 0 6,90019935 314 650.0 9,750

Heat TreatedlZinc Plated20005 114 30.0 2,60020010 5116 52.0 3,90020015 316 86.0 5,40020020 7H6 140.0 7,20020025 112 200.0 9.2002003020035

Tumble Bright Finish20105

518 360.0 14:ooo314 650.0 19,900

114 36.0 1.25020110 5116 56 0 1:90020115 318 93.0 2,65020125 112 232.0 4,500

Heat meatedlZinc Plated20205 114 36.0 2,80020210 5116 56 0 3 9””20215 31820220 7116

G.0144.0

_,___5,4007.200

20225 112 232.0 9:200

Tumble Bright Finish2030520310203152032020325

114 34 0 1,2505116 84.0 1,900318 102.0 2,6507116 144.0 3,500112 2160 4 SO”

Heat TreatedlZinc Plated

20405 114 34.0 2,60020410 5116 64.0 3,90020415 318 1020 5,40020420 7116 144.0 7,20020425 112 216.0 9,200

All untreated chain hardware meets applicable Federal Specificahons RR-C-27lb.All heat treated chain hardware meets requirements for Hi-Test Chain.WARNING: Use heat treated hooks only with HI-Test Chain.

CHAIN SLIP HOOKSForged l Carbon Steel l Self-Colored

CHAIN GRAB HOOKSForged l Carbon Steel l Self-Colored

CLEWS SLIP HOOKSForged l Carbon Steel l Self-Colored

CLEVIS GRAB HOOKSForged l Carbon Steel l Self-Colored


DOUBLECLEVIS LINKSForged l Electra-Zinc Plated

CONNECTINGLINKSForged l Zinc Plated

I CAi i

Forged steel, Quenched and Tempered.

CHAINREPAIRLINKSZinc Plated

Stock No.Chain Size Chain SireHigh Test TransportDrade 43 Orade 70

wt. Perloo PCS.

UltimateStrength

Lb.Bulk Pack

20700 % 01 %6 ‘/4 33 13,00020701 3/u % 6 49 16,60020705 %6 or ‘I2 =/a 105 26,000

SpaciflcatlonsChain Sire A S C X Y X

l/4 or %6 ’ 2/32 2/i 54 6 1% w8 ~%fi

3/a % ‘A 6 % r%6 3x2 11x2X6 or Y2 2x2 % 6 % 12%2 32%2 2

l Designed for linking all popular sizes of chain to rings, end links, eye hooks, pad eyes,tractor eyebolts. etc.

l Pin can be removed with pliers or screwdriver.l All pins alloy steel, Quenched and Tempered.

ZlllCPlatedStock

no. SlZe

InsldeDlmenslons

Wldth LengthW L

Approx.wt. Per

iooPCS.

Ylll.Rated

Cpppslty

,_ ,” .”16610 % 6 ‘%2 x 2x2 10.0 2;10016615 3/s % 6 x 1 % 18.0 2,60016620 % 6 %2 x 1%6 26.0 3,50010025 % 22/22 x 1’%2 39.0 4,15016630 =/s ‘Yw x 1% 75.0 6,25010835 % 17% x 2 120.0 9.000._.18640 % 1 ‘/s x 2’732 170.0 12;ooo16645 1 I’%6 x 2’%6 242.0 15,500

Safety Factor 4 to 1.

Stock No. Wire Dia.40700 3/r 640705 ‘/440710 % 640715 %40720 %

Inslde Inside Approx.Length Width wt. Per

L W loo PCS.1 % 3.251% % 6.501% Y4 13.252 % 26.002% 1 55.00

COLD SHUTSForged l Self-Colored

I 1

StockNO.

Tumble Bright Flnlth195001950519510195151952019525195301953519545

Sire of wt. PW RatedChpln 100 PCS. Capaclty

% 6 2.5 750‘/4 5.5 1,250%6 10.0 1,900% 16.5 2,650% 6 25.0 3,500% 37.0 4,500% 79.0 6,900% 132.5 9,750

1 303.0 13,950

1

-. I.D. Thread Shank OVMM Appror.Stock Thread EW Length Length Length wt. Perno. DIO. A B C D 100 PCS.

21370 8-32 '/4 1 l'/lS 1% 1.221371 8-32 % 1 l%S 1% 1.421380 lo-24 %5 1% 1% 1 % 1.621381 lo-24 3/a 7/s 1 1'%6 1.521382 lo-24 =/8 I_ 2 2'%6 2.021383 lo-24 3/n 1% 3 3"/,. 2.5._ ._ ._21390 12-24 % 1 YE 1x6 2 % 2.521400 114-20 %5 % 1 2 3.621410 114-20 % 6 1% 1 % 2% 4.021420 l/4-20 % 1 % I'%6 2 % 4.021430 114-20 %6 1 % 2 4.621440 114-20 %6 1 % 2 %

:I/,5.2

21450 114-20 % 6 1% 3 4 5.421460 114-20 % 6 1 % 4 5 6.621470 114-20 9/,. 1 'h 5 6 7.021500 5/16-1821510 5/16-1821520 S/16-1821530 J/16-18

,_21 YE22%

2%6 3 % 7.81 % 3 % 8.22 % 4 9.93 % 5 11.6

21540 5116-18 % 2% 4 % 6 13.421600 316-16 5/a 2 % 2 % 3 % 13.221610 316-16 1 2 %

2%2 % 4 15.7

21620 316-16 1 3 % 5 16.821630 316-16 1 2 % 4 % 6 20.621640 316-16 1 2 % 6% 8 25.321650 318-16 1 2 % 7 % 9 % 29.221660 3/E-16 1 2 % 9 % 11 '/2 37.021670 316-16 1 2 % 11% 13% 41.021700 7/16-14 1 w2 4 6 27.221710 7/16-14 1 2% 6 8 35.321720 7116-14 1 2 % 0 10 41.821730 7116-14 1 2% 10 12 48.521740 112-13 1 2 % 3 5 34.021750 112-13 1 3 4 6 37321760 112-13 1 : 5 7 42.321770 112-13 1 6 8 46.221780 112-13 1 3 a 10 54.321790 112-13 1 3 10 12 63.521800 516-11 1% 3 3 % 6 62.521810 516-11 1% 3 5 % 8 74.621820 616-11 1% 3 7 % 10 90.521830 516-11 1% 3 9 % 12 103.5

24500 l/4-20 % 5 '/a 1 2 3.624510 114-20 % 1% 1 % 2 % 4.024530 114-20 %6 1% 2 3 4.624540 114-20 %6 1% 3 4 5.424550 114-20 % 1% 4 5 6.624560 114-20 %6 1% 5 6 7.024630 5116-18 % 1% t's6 3 % 8.224640 5116-18 % 2 2 % 4 9.924650 5/16-18 % 2 % 3 % 5 11.624660 5116-18 % 2 % 4 % 6 13.424740 316-16 1 2 % 2 % 4 15.724750 316-16 1 2 % 3 % 5 16.824760 316-16 1 2 % 4 % 6 20.624780 316-16 1 2 % 6% 8 25.3

BENT EYESCarbon Steel l Zinc Plated

NOT RECOMMENDEDFOR LIFTING

l Furnished with hex nuts (unassembled)l Available bulk onlyl All sizes manufactured with rolled threads

up to '/2"l Special packaging available upon requestl Available in 304 stainless steelSee page 35

DEDWARD W. DANIEL CO.DIAMOND 0 BRAND HARUWARE...ASOURCEYOUCANDEPENUlJN

BENT EYESWELDED CLOSEDCarbon Steel l Zinc Plated

NOT RECOMMENDEDFOR LIFTING


Please include stock number and size when o-tiering

U-BOLTSUnassembledWith NutsCarbon Steel l Zinc Plated

l All sizes manufactured with rolledthreads.

l Cut thread available upon request.l U-bolts available up to 1%"diameter rod

l Squareand V-bend bolts awlableupon request.

l Send drawmg forspecialsizes.l Bulk packaging.l Special packaging availableupon request.

l Available in 304 Stainless Steel

SQUARE BENDU-BOLTSUnassembled*With NutsCarbon Steel l Zinc Plated

STRAP WASHERSZinc PlatedCarbon Steel l Zinc Plated

Thread Width Inside ThreadStock Dia. wt. per

NO. Aq et.;egs Le,nCpth LenDgth ‘,;t

100 PCS.34010 114-20 % 1% % 3/a 4.034020 114-20 % 1% % 3/a 5 834030 114-20 % 2% 1% 3/a 6.834070 114-20 1 1 % % % 6.034080 114-20 1 ‘/s 2 % % 6.534090 114-20 1% 2% % 1 7.434100 114-20 1% 2% 1 1% 8.534110 114-20 2 3’/” 1 'A l'/,

‘-9.5

34120 114-20 1% 3;/; 2’- 1 9.834200 5116-18 1% 2 % 1 1 11.634210 5116-18 1% 3'%6 1% 1 16.534220 5116-18 1% 2'%6 1 1% 13.634240 5116-18 2 21x6 1 1% 13.634250 5116-18 2 3"h. 1 '/? 1'X 17.2,”34270 5116-18 2% 3 % 1% 2 “ 16.034292 316-16 1 2 % 1 '/a % 17.734301 316-16 1% 3 % 1% 1 21.534303 316-16 1% 2 % 1% 1 19.234304 316-16 2- 3% 1 I/, 1% 23.034310 316-16 2 % 3 % 1% 2 24.934320 316-16 3 4% 1 % 2% 28.034330 316-16 3 % 4 % 1% 3 32.334400 112-13 3 4’/2 1% 2’/2 58.034410 112-13 3'/,

4-5 1'X 3

34420 112-13 5’/2 1;/;66.5

3 % 68.034430 112-13 4 % 6 1% 4 74.034440 112-13 5 % 7 2 5 86.534450 112-13 6% 8 2 6 101.534455 112-13 8 % 103/B 2 8 125.034474 5/6-11 8 % 11% 4 8 253.0

Stock wt. PerNO. 100 PCS.

With Strap Washersand Nuts Unassembled

35407 9.535408 10.135409 10.835410 13.335411 14.435412 14.635420 16.435421 21.235422 18.335424 19.535425 23.235427 21.8

_ -35429 31.1

35430 31.835431 38.035432 41.235433 46.3

StockNO.

3600036005360103601536020

Thread Width Inside ThreadDia. Bet. Legs Length Length

A g C D316-16 2 3 1 %316-16 2 5 3316-16 2 7 3 %316-16 4 3 1'/2316-16 4 5 3

wt. Per100 PCS.

20.029.639.224.834.4

36025 316-1636030 3/6-1636035 3/6-1636040 316-16

'Strap Washers not included.

4 7 3 % 57.06 5 3 39.26 7 3 % 63.26 9 5 % 59.6

Width Approx. DlmenslonsBetween Length

Stock slots OVerSIll Thlck- Slot wt. PerNO. A B ness size 1 Do PCS.

35501 ‘%2 2’732 %2 %2 x “h 3.535502 1 % 3x6 %2 %2 x “/I6 3.835503 1 '/4 3%2 %2 “A2 x “/I6 4.835504 1'%6 3"/16 %2 1x2 x 1% 5.935505 1 % 3%6 '/8 '/I6 x % 9.635506 2 % 43/8 ‘/8 ‘/I16 x 2/G 13.135507 3% 5% '/a '116 x % 14.0

Strap washers for '/2" diameter U-bolts are available upon request.

‘Ek U-Bolt Stock Nos.Stock

NO. U-Bolt Stock Nor.35501 34000thru 34090 35504 34240, 34250, 3427035502 34100, 34110, 34120 35505 34303, 34301, 3430235503 34200, 34210.34220, 35506 34310, 34320

34230 35507 34330



Stockno.

4018640187

Thread OVergIlDia. Length

A B5116 4%318 5

I.D. Eye Approx. Wt.C Per too PCS.7/a 10.2

1 16.0

Stockno.

4018440185

ThreadDia.

AS/l6318

OverallLength

B3%4%

I.D. Eye Approx. Wt.C Per 100 PCS.% 10.0Yi 14.2

StockNO.

4019140192

Thread Overall ShankDIP. LengthA B LenCth

I.D. Eye Approx. Wt.D Per t 00 PCS.

5116 3 % 2 % 5/a 10.6316 4 2 % % 14.5

StockNO.

41705

InsideLength I.D. Eye Approx. Wt.SlZe Wire DIP. A B Per too PCS.

5132 .134 1 1341710 311641715 114 .250 6.741720 5116 ,313 1% 3/n 11.041725 316 ,375 2?& 1% 20.4

StockNC..

4139041391413924139341394

Shank ShankDIP. Length

A B114 261i6 2 %316 2 %112 3%516 4

ThreadLYYh

1%22 %2 %2 %

I.D. EyeD%%%

11%


5.09.0

15.236.075.0

CLOTHESLINEHOOKSZinc Plated

PORCHSWINGHOOKSZinc Plated

LAGSCREWEYESZinc Plated

S-HOOKSZinc Plated

FORGEDSCREW EYEBOLTSHot Galvanized*Available up to 1'‘Cut lag thread.-No gimlet point.


MEDIUM HEAVYFLANGE PILOT TYPEForged l Carbon Steel l Self Colored

EXTRA HEAVYFLANGE FLAT TYPEForged l Carbon Steel l Self Colored

FORGED TANK FLANGECarbon Steel l Self Colored

STANDARD HEAVYCURVED FLANGEForged l Carbon Steel l Self Colored

Approx.Stock Pip.2 wt. Per

no. Size A B E F It I loo PCS.60000 '/a I%6 7/a '%6 %2 % '/a 1060005 '/4 I%6 7/a '%6 %2 % '/a 960010 3/a 1% '/8 '% 6 J/32 ‘18 ‘h 760015 % 1 YE l%S 1% %2 % 5 % 6 1260020 % I’%6 1%6 136 x2 ‘/2 % 6 1960025 1 2 % 1% l"h %2 %6 'h 2960030 1% 2%6 l'% 2 %2 %6 '/4 3360035 1 '/2 2'%6 2%6 2% %2 % 5 '/4 3760040 2 3 % 2 % 2 % %2 % 'h 51

APRW~.Stock Pipe wt. Per

NO. Size A B F n 1OOPCS.

60215 '/2 2 1 '/4 '/a % 3260220 % 2'/, 1 '/2 '/a % 44

60225602306023560240

2% 1%3 2x6

3'h 2563 % 2 %

60245 2 % 4% 3 % '/a 1 14560250 3 5 % 4'/4 '/a 1 29060255 3 % 6 47/a '/4 1 35660260 4 6% 5% 'Ia l'h 410

StockNO.

60300603056031060315603206032560330603356034060345603506035560360

Approx.Pipe wt. Part37.e A B E F H I 100 PCS.

'h 1 % 1 'VI6 %2 %6 '/4 12'14 1 % 1 '% %2 %6 % 123/8 1% 1 '%6 %2 % 5 '/4 12'/2 13/a I%6 1 ‘/a %2 =/a ‘/a 17% 2% 1x6 1 % %2 1'/'6 '/4 23

1 2 % 1% 1 % %2 314 '/4 361 'h 2"h 2 % 2 K2 % '/4 45I'/2 3 2 % 2 % %2 % '/4 532 3% 2 % 2 % x2 2%2 '/4 742 % 4% 3%2 3% '/s 1 % 5 1103 4 % 3'%6 3 % '/a 1 %5 1263% 5'h 456 4 % '/a 1 % 1354 5'%6 4'%6 4?& 'h 1x2 % 212

Stock PipeNo. Size A q E F Ii I Rsdhs 100 PCS.

60420 % 2 1 % 1'%2 ‘h % S/l 6 7 3260425 1 2 % 1 % 1 % 'h % '/4 15 3960430 1% 2"/16 2'h 1% 'h "/ICC 3/l 6 7 4460435 1 '/2 3x6 256 2"/32 '/a 2% % 6 8% 5160437 1 % 3x6 256 2'%2 '/a %2 % 6 15 5160440 2 3 % 2 % 2’9h ‘/a % 732 7 8160442 2 3% 2 % 2'%2 'h VI2 %2 15 8160445 2% 4%6 39/z 3% % 1 '/a 27 11960450 3 4 % 3'%6 3 % 'h 1 '/4 27 14060452 3 4 % 3'%6 3 % '/a 1 '/4 1 1 % 16260455 3 % 5'/a 4x6 4% '/a 1 'h 27 16860460 4 5'%6 5'/, 4 % '/a 1x2 ’ %2 27 21660465 5 7'/a 6% 5'%6 '/4 1 % % 6 40 400

'Specify radius


[email protected] your supplier, daniel diamond“d” lifting eve qualitv checklist a normalizedprior...

Documents