d&s_1_ lesson 24
TRANSCRIPT
-
7/24/2019 D&S_1_ LESSON 24
1/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 1/14
Home Courses Existing Courses UG Courses - Agricultural Engineering Agricultural
Engineering D&S_1 MODULE 11. LESSON 24. Basic Rules for Design of Beams and Slabs
Design of Structures 3(2+1)You are currently using guest access (Log in)
LESSON 24. Basic Rules for Design of Beams and Slabs
24.1 INTRODUCTION
The details given below are based on the recommendations made in IS: 456-
1978.
24.2. EFFECTIVE SPAN
(a) For simply supported beam and slab: The effective span of a simply
supported beam or slab is taken as the distance between the centre to centre of
support or the clear distance between the supports plus the effective depth of
the beam of slab whichever is smaller.
(b) For continuous beam or slab: In case of a continuous beam or slab,
where the width of the support is less than 1/12 the clear span, the effective
span shall be worked out by following the rule given in (a) above.
In case the supports are wider than 1/12 of the clear span or 600 mm
whichever is less, the effective span shall be taken as under.
(i)For end span with one end fixed and the other continuous or for
intermediate spans, the effective span shall be the clear span between
supports.
(ii)For end span with one end free and the other continuous, the effective
span shall be equal to the clear span plus half the effective depth of thebeam or slab or the clear span plus half the width of the discontinuous
support, whichever is less.
Note: In case of span with roller or rocker bearings the effective span shall
always be the distance between the centres of bearings.
(c) Frames. In the analysis of a continuous frame, effective span shall be
taken as the centre to centre distance between the supports.
24.3 CONTROL OF DEFLECTION/DEPTH OF BEAMS AND SLABS
It is necessary to impose a check on the magnitude of deflection in a
structural member with a view to ensure that the extent of deflection does not
Navigation
http://ecoursesonline.iasri.res.in/course/index.php?categoryid=4http://ecoursesonline.iasri.res.in/login/index.phphttp://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511http://ecoursesonline.iasri.res.in/course/view.php?id=64http://ecoursesonline.iasri.res.in/course/index.php?categoryid=4http://ecoursesonline.iasri.res.in/course/index.php?categoryid=3http://ecoursesonline.iasri.res.in/course/index.php?categoryid=2http://ecoursesonline.iasri.res.in/course/index.phphttp://ecoursesonline.iasri.res.in/ -
7/24/2019 D&S_1_ LESSON 24
2/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 2/14
adversely affect the appearance or efficiency of the structure or finishes or
partition etc. Control on deflection is also necessary to prevent structural
behavior of the member being different from the assumption made in the
design. As per Code for beams and slabs, the vertical deflection limits may be
assumed to be satisfied, provided that the span to depth ratio are not greater
than the values obtained as below.
(a) Basic values of span to effective depth ratios for spans up to 10m.
(i) Cantilever 7
(ii) Simply supported 20
(iii) Continuous 26
(b) For spans above 10m, the values in (a) may be multiplied by 10/span in
metres, except for cantilever in which case deflection calculations should be
made.
(c) Depending on the area and the type of steel for tension reinforcement the
values in (a) or (b) shall be modified as per Fig.24.1.
(d) Depending on the area of compression reinforcement the values of span to
depth ratio shall be further modified as per Fig.24.2.
(e) For flanged beams, the values of (a) or (b), be modified as per Fig.24.3
and the reinforcement percentage for use in Fig. 24.1 and Fig. 24.2 should be
based on area of section equal to .
Note 1. For slabs spanning in two directions, the shorter of the two spans
should be used for calculating the span to effective depth ratios.
Note 2. For two-way slabs of small spans (up to 3.5m) with mild steel
reinforcement, the span to overall depth ratios given below may generally be
assumed to satisfy vertical deflection limits for loading class upto 3000 N/m2.
Simply supported slabs 35
Continuous slabs 40
For high strength deformed bars, of grade Fe 415, the values given above
should be multiplied by 0.8.
24.4 SLENDERNESS LIMITS FOR BEAMS
To ensure lateral stability, a simply supported or continuous beam shall be so
proportioned that the clear distance between the lateral restraints does not
exceed 60 b or whichever is less, where dis the effective depth of the
beam and b, the breadth of the compression face mid-way between the lateral
-
7/24/2019 D&S_1_ LESSON 24
3/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 3/14
restraints.
For a cantilever, the clear distance from the free end of the cantilever to the
lateral restraint shall not exceed 25b or whichever is less.
24.5 REINFORCEMENT IN BEAMS
24.5.1 Tension Reinforcement
(i) Minimum reinforcement: The minimum area of the tension
reinforcement in beams shall not be less than that given by the following
expression
(ii) Maximum reinforcement: The maximum area of tensionreinforcement in a beam shall not exceed 0.04 b D. Where D is the
overall depth of the beam.
24.5.2 Compression Reinforcement
The maximum area of compression reinforcement in a beam shall not
exceed 0.04 bD. For effective lateral restraint, the compression
reinforcement in beams shall be enclosed by stirrups.
24.5.3 Side Face Reinforcement
Where the depth of the web in a beam exceeds 750 mm, side face
reinforcement shall be provided along the two faces. The total area of
such reinforcement shall be not less than 0.1 per cent of the web area and
shall be distributed equally on the two faces at a spacing not exceeding
300 mm or web thickness whichever is less.
24.5.4 Minimum Area of Shear Reinforcement
Minimum shear reinforcement in the form of stirrups shall be provided
that
-
7/24/2019 D&S_1_ LESSON 24
4/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 4/14
24.5.5 Maximum Spacing of Sheer Reinforcement
Maximum spacing of shear reinforcement measured along the axis of the
member shall be as under
(i) For vertical stirrups 0.75d or 450mm whichever is less
(ii) For inclined stirrups at 45 d or 450mm whichever is less
24.6 REINFORCEMENT IN SLABS
24.6.1 Minimum Reinforcement
The area of reinforcement in either direction in slabs should not be less
than 0.15 per cent of the total cross-sectional area in case mild steel bars
are used as reinforcement. In case of high strength deformed bars of
welded wire fabric, this value can be reduced to 0.12 per cent.
24.6.2 Maximum Diameter
The maximum diameter of the reinforcing bar in a slab should not exceed
1/8thof the total thickness of the slab.
24.7 CLEAR COVER TO REINFORCEMENT
The clear cover of concrete (excluding plaster or other decorative finish) to
reinforcement in different structured members should be as under.
(a) The clear cover for tensile, compressive, shear or any other
reinforcement in slab shall not be less than 15 mm or the diameter of the
reinforcing bar whichever is more.
(b) The clear cover of longitudinal reinforcing bar in the beam shall not
be less than 25 mm or the diameter of the reinforcing bar whichever is
more.
-
7/24/2019 D&S_1_ LESSON 24
5/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 5/14
(c) The clear cover at each end of reinforcing bar in the beam or slab
shall not be less than 25 mm or twice the diameter of such bar whichever
is more
(d) The clear cover for a longitudinal reinforcing bar in a column shall
not be less than 40 mm or the diameter of the reinforcing bar which
is more. However in case of columns having minimum dimensions of 200
mm or less, and whose reinforcing bar diameter does not exceed 12mm, a
clear cover of 25 mm can be adopted.
(e) The clear cover for any other reinforcement should not be less than 15
mm or the diameter of the reinforcing bar whichever is more.
(f) In case the surface of concrete of a structural member is exposed to
action of harmful chemicals, acids, vapours, saline atmosphere,
sulphurous smoke etc. or concrete surface is in contact with earth
contaminated with such chemicals, it is necessary to provide increasedcover. The increase in cover may be between 15 mm to 50 mm over and
above the values of cover specified in (a) to (e) above.
(g) For reinforced concrete members periodically immersed in a sea
water, or subjected to sea spray, the cover of concrete shall be 50 mm
more than specified in (a) to (e) above.
Note 1. When concrete of grade M 25 and above is used in R.C.C. work, the
additional thickness of cover as specified in (f) and (h) above may be reducedto half.
Note 2.In all such cases the cover should not exceed 75 mm.
24.8. SPACING OF REINFORCEMENT
24.8.1 Minimum distance between Individual Bars
(i) The minimum horizontal distance between two parallel main
reinforcing bars shall not be less than the diameter of the bar (in case ofunequal diameter bars, the diameter of the larger bar is considered) or
5mm more than the nominal maximum size of coarse aggregate used in
the concrete, whichever is more.
(ii) In case where it is desired to provide main bars in two or more layers
one over the other, the minimum vertical clear distance between any two
layers of the bars, shall normally be 15 mm or two-thirds the nominal
maximum size of aggregate or the maximum size of the bar whichever is
the greatest.
24.8.2 Maximum Distance between Bars in Tension
(i) The pitch of the main tensile bars in R.C. slab should not exceed three
-
7/24/2019 D&S_1_ LESSON 24
6/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 6/14
times the effective depth of the slab or 450 mm whichever is smaller.
(ii) The pitch of the bars provided to act as distribution bars or bars
provided to guard against temperature and shrinkage in an R.C. slab, shall
not exceed five times the effective depth of the slab or 450mm,
whichever is smaller.
24.9 CURTAILMENT OF TENSION REINFORCEMENT IN FLEXURALMEMBERS
(a) The main reinforcement in beams and slabs may be curtailed or bent up,
beyond the point at which it is no longer required to resist bending. The
curtailed reinforcement shall, however, extend beyond that point, for a
distance equal to the effective depth of the member or 12 times the bar
diameter whichever is greater except at simple supports or end of cantilever.
Besides this, certain requirement regarding shear will have to be satisfied as
per provision in the relevant clause in the code.
(b) Positive moment reinforcement
(i) At least one-third of the positive moment reinforcement in simply
supported member and one-fourth of the positive moment reinforcement
in case of continuous member should extend along the same face of the
member into support to a length = /3 where = development length of the
bar.
(ii) When a flexural member is part of primary lateral load resisting
system, the positive reinforcement required to be extended into the
support as described in (b) above shall be anchored to develop its design
stress in tension at the face of the support.
-
7/24/2019 D&S_1_ LESSON 24
7/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 7/14
Let c = side cover to the reinforcing bar.
x = length of the bar from centre line of the support to the beginning of
the hook.
L0= sum of anchorage beyond the centre of support and the equivalent
anchorage value.
In Fig. 24.4 the blackened portion of the bar shows the standard hook
having an anchorage value of 16. In case of standard hook of mild steel
reinforcement the anchorage value of the length of the bar between the
beginning of the hook and the outer face of the hook can be taken as 3.
-
7/24/2019 D&S_1_ LESSON 24
8/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 8/14
(c) Negative moment reinforcement. At least one-third of the total
reinforcement provided for negative moment at the support shall extend
beyond the point of inflection for a distance not less than the effective depth
of the member or 12 or one sixteenth of the clear span whichever is greater.
24.10 LAP SPLICE
When it is necessary to provide laps in reinforcing bars the length of lap shall
not be less than the following values. The splices should be staggered and as
far as possible provided away from sections of maximum stress.
24.10.1 Lap Length for Bars in Flexural Tension
The minimum lap length for bars in flexural tension including anchorage
value of hooks shall be greater of the following
The straight length of lap shall, however, not be less than 15 or 20 cm.
If be the diameter of plain m.s.round bar be the actual tensile stress in
bar M 15 be the grade of concrete used (for which design bond
stress=0.6 N/mm2), the lap length of bar for case (ii) above will be
-
7/24/2019 D&S_1_ LESSON 24
9/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 9/14
24.10.2 Lap Length for Bars in Direct Tension
The minimum lap length for bars in direct tension including anchorage
value of hooks shall be greater of the following:
(i) 30
(ii) 2Ld
24.10.3 Lap Length for Bars in Compresion
The minimum lap length for bars in compression shall be greater of the
following
24.10.4 Splicing Bars of Different Diameter
When bars of two different diameter are to be spliced, the lap length shall becalculated on the basis of the smaller diameter bar since the force to be
transmitted at the slice is governed by the thinner bar.
24.11 ANCHORAGE VALUE OF BEND
If a bar in tension has its end bent to a hooked shape, the calculated
development length of the bar shall be reduced by a length equal to the
anchorage value of the type of hook provided. The anchorage value of
standard semi-circular hook, 45 bend and standard L-hook is taken as 16 ,12 and 8 respectively of the hooked bar.
For a bar in compression, no hooks need be provided as they deprive the bar
of its proper axial end bearing and also tend to cause outward buckling of the
-
7/24/2019 D&S_1_ LESSON 24
10/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 10/14
bar.
Normally, deformed bars are not provided with end hooks.
24.12 BENDING MOMENT CO-EFFICIENTS FOR BEAMS AND SLABS
The following cases are considered:
(a) Simply supported members
(b) Members continuous over two spans
(c) Members continuous over three or more spans.
24.12. 1 For Simply Supported Members
In case of simply supported beams and slabs, resting on two supports or
having only one span and loaded with uniformly distributed load
Max +ve B.M. is given by
Where
w = {Sum of total dead load + imposed load (fixed) + imposed load
(not fixed)} in Newton per metre.
and l = effective span of the member in metres.
24.12.2 For Members Continuous Over Two Equal or Approximately
Equal Spans
In case of beams and slabs continuous for two equal or approximately
equal spans (the spans are considered approximately equal when they do
not differ in length by more than 15% of the longest span) and loaded
with uniformly distributed load.
24.12.3 For Members Continuous Over three of more Approximately
-
7/24/2019 D&S_1_ LESSON 24
11/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 11/14
Equal Spans
In case of beams and slabs continuous over three or more approximately
equal spans (the spans are considered approximately equal when they do
not differ in length by more than 15% of the longest span) and loaded
with uniformly distributed load, the bending moments at the mid-span
and support can be worked out by use of the following formulae as given
in IS: 456-1978.
where
wd= Total dead load and imposed load (fixed)
ws= Total imposed load (not fixed)
l= effective span
24.13 SHEAR FORCE CO-EFFICIENTS FOR BEAMS AND SLABS
24.13.1 For Beams and Slabs Simply Supported over Span or Continuous
for Two Spans
In case of beams and slab simply supported over one span or continuous
for two spans and loaded with uniformly distributed load, the shear force
is given by
24.13.2 For Beams and Slabs Continuous over three or more Spans
-
7/24/2019 D&S_1_ LESSON 24
12/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 12/14
In case of beams and slabs continuous over three or more spans which do
not differ by more than 15% and loaded with uniformly distributed load,
the shear force at different supports can be worked out by use of
following formulae as given in IS: 456-1978.
24.14 MODULAR RATIO
The value of modular ratio m for any desired grade of concrete can be
obtained by the empirical formula
Where cbcis permissible compressive stress due to bending in concrete in
N/mm2.
24.15 UNIT WEIGHT OF PLAIN CONCRETE AND R.C.C.
Based on recommendation in revised code, the unit weight of plain cement
concrete and reinforced cement concrete shall be taken as 24000 N/m3 and
25000 N/m3respectively.
24.16 GENERAL
1. The check for bond stress specified in the earlier code is now replaced by
the concept of development length. In order to ensure development of
required stresses in reinforcing bar at any section, it is necessary to extend the
bar on either side of the section by appropriate development of length.
2. It is desirable to use one type of reinforcing steel bar (either plain bars ordeformed bars) in the design or detailing of a member to avoid chances of
error while executing the work. The secondary reinforcement like lies and
stirrups can however, invariably be of mild steel even when the main
-
7/24/2019 D&S_1_ LESSON 24
13/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
http://ecoursesonline.iasri.res.in/mod/page/view.php?id=2511 13/14
reinforcement consists of HYSD bars.
Fig. 24.1 Modification factor for tension reinforcement
Fig. 24.2 Modification factor for compression reinforcement
-
7/24/2019 D&S_1_ LESSON 24
14/14
21/12/2015 D&S_1: LESSON 24. Basic Rules for Design of Beams and Slabs
You are currently using guest access (Log in)
D&S_1
Fig. 24.3 Reduction factor for ratios of span to effective depth for flanged beams
Fig. 24.4 Curtailment of tension reinforcement in flexural members
Last modified: Friday, 28 March 2014, 8:27 AM
http://ecoursesonline.iasri.res.in/course/view.php?id=64http://ecoursesonline.iasri.res.in/login/index.php