driver controls mir a · mir-2 < wiring diagram > door mirror wiring diagram door mirror...
TRANSCRIPT
DRIVER CONTROLS
C
D
E
SECTION MIR A
B
MIRRORS
F
G
H
I
J
K
M
IR
N
O
P
CONTENTS
M
WIRING DIAGRAM ....................................... 2
DOOR MIRROR ................................................... 2Wiring Diagram - With Heated Mirrors ......................2Wiring Diagram - Without Heated Mirrors .................6
INSIDE MIRROR ................................................10Wiring Diagram - With Homelink Universal Trans-ceiver .......................................................................10Wiring Diagram - Without Homelink Universal Transceiver .............................................................13
PRECAUTION ..............................................16
PRECAUTIONS ..................................................16Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-SIONER" .................................................................16
PREPARATION ...........................................17
PREPARATION .................................................17Special Service Tool ................................................17Commercial Service Tool ........................................17
UNIT REMOVAL AND INSTALLATION ......18
INSIDE MIRROR ...............................................18Inside Mirror Assembly ............................................18
DOOR MIRROR ................................................19Door Mirror Assembly ..............................................19Door Mirror Glass ....................................................20
UNIT DISASSEMBLY AND ASSEMBLY ....21
DOOR MIRROR ................................................21Mirror Actuator .........................................................21
MIR-1Revision: November 2012 2012 Frontier
DOOR MIRROR
< WIRING DIAGRAM >WIRING DIAGRAMDOOR MIRRORWiring Diagram - With Heated Mirrors INFOID:0000000007327330
AALWA0553GB
MIR-2Revision: November 2012 2012 Frontier
DOOR MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< WIRING DIAGRAM >
M
AWLIA0426GB
MIR-3Revision: November 2012 2012 Frontier
DOOR MIRROR
< WIRING DIAGRAM >AALIA1116GB
MIR-4Revision: November 2012 2012 Frontier
DOOR MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< WIRING DIAGRAM >
M
AALIA1117GB
MIR-5Revision: November 2012 2012 Frontier
DOOR MIRROR
< WIRING DIAGRAM >Wiring Diagram - Without Heated Mirrors INFOID:0000000007327331ABLWA2005GB
MIR-6Revision: November 2012 2012 Frontier
DOOR MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< WIRING DIAGRAM >
M
ABLIA4447GB
MIR-7Revision: November 2012 2012 Frontier
DOOR MIRROR
< WIRING DIAGRAM >ABLIA4448GB
MIR-8Revision: November 2012 2012 Frontier
DOOR MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< WIRING DIAGRAM >
M
ABLIA4449GB
MIR-9Revision: November 2012 2012 Frontier
INSIDE MIRROR
< WIRING DIAGRAM >INSIDE MIRRORWiring Diagram - With Homelink Universal Transceiver INFOID:0000000007327332ABLWA1220GB
MIR-10Revision: November 2012 2012 Frontier
INSIDE MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< WIRING DIAGRAM >
M
ABLIA2819GB
MIR-11Revision: November 2012 2012 Frontier
INSIDE MIRROR
< WIRING DIAGRAM >ABLIA2820GB
MIR-12Revision: November 2012 2012 Frontier
INSIDE MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< WIRING DIAGRAM >
M
Wiring Diagram - Without Homelink Universal Transceiver INFOID:0000000007327333
ABLWA1219GB
MIR-13Revision: November 2012 2012 Frontier
INSIDE MIRROR
< WIRING DIAGRAM >ABLIA2817GB
MIR-14Revision: November 2012 2012 Frontier
INSIDE MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< WIRING DIAGRAM >
M
ABLIA2818GB
MIR-15Revision: November 2012 2012 Frontier
PRECAUTIONS
< PRECAUTION >PRECAUTIONPRECAUTIONSPrecaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000007327334
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used alongwith a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certaintypes of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRSsystem uses the seat belt switches to determine the front air bag deployment, and may only deploy one frontair bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.Information necessary to service the system safely is included in the SR and SB section of this Service Man-ual.WARNING:• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed byan authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personalinjury caused by unintentional activation of the system. For removal of Spiral Cable and Air BagModule, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in thisService Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERSWARNING:• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with ahammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causingserious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect thebattery, and wait at least 3 minutes before performing any service.
MIR-16Revision: November 2012 2012 Frontier
PREPARATION
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< PREPARATION >
M
PREPARATIONPREPARATIONSpecial Service Tool INFOID:0000000007327335
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool INFOID:0000000007327336
Tool number(Kent-Moore No.)Tool name
Description
—(J-39570)Chassis ear
Locating the noise
—(J-43980)NISSAN Squeak and Rat-tle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
(Kent-Moore No.)Tool name
Description
(J-39565)Engine ear
Locating the noise
SIIA0995E
MIR-17Revision: November 2012 2012 Frontier
INSIDE MIRROR
< UNIT REMOVAL AND INSTALLATION >UNIT REMOVAL AND INSTALLATIONINSIDE MIRRORInside Mirror Assembly INFOID:0000000007815413
REMOVAL1. Remove the mirror finisher (if equipped).2. Remove the screw and slide the mirror upward to remove.3. Disconnect the connector (if equipped).4. Remove the mirror.
INSTALLATIONInstallation is in the reverse order of removal.
1. Inside mirror 2. Inside mirror finisher (If equipped)
LIIA0277E
MIR-18Revision: November 2012 2012 Frontier
DOOR MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< UNIT REMOVAL AND INSTALLATION >
M
DOOR MIRRORDoor Mirror Assembly INFOID:0000000007327339
EXPLODED VIEW
NOTE:Power mirror shown, manual mirror similar.
MANUAL MIRRORCAUTION:Be careful not to damage the mirror body.Removal1. Remove the front door sash cover.2. Remove the front door finisher. Refer to INT-15, "Removal and Installation".3. Remove the nuts and the door mirror assembly.InstallationInstallation is in the reverse order of removal
POWER MIRRORCAUTION:Be careful not to damage the mirror body.Removal1. Remove the front door sash cover.2. Remove the front door finisher. Refer to INT-15, "Removal and Installation".3. Disconnect the door mirror harness connector.4. Remove the nuts and the door mirror assembly.InstallationInstallation is in the reverse order of removal.
AWIIA1222GB
MIR-19Revision: November 2012 2012 Frontier
DOOR MIRROR
< UNIT REMOVAL AND INSTALLATION >Door Mirror Glass INFOID:0000000007327340REMOVAL
1. Angle the mirror fully up.2. Remove the door mirror.
• Pull from the bottom to disengage the clips.• Continue to pivot the mirror upward from the bottom to separate the hooks.• Disconnect the harness connectors (if equipped).
INSTALLATIONInstallation is in the reverse order of removal.
LIIA1694E
MIR-20Revision: November 2012 2012 Frontier
DOOR MIRROR
C
D
E
F
G
H
I
J
K
M
A
B
IR
N
O
P
< UNIT DISASSEMBLY AND ASSEMBLY >
M
UNIT DISASSEMBLY AND ASSEMBLYDOOR MIRRORMirror Actuator INFOID:0000000007327341
DISASSEMBLY AND ASSEMBLYDisassembly1. Remove the door mirror glass. Refer to MIR-20, "Door Mirror Glass"2. Remove the screws (A) and release the actuator from housing
(B).
3. Disconnect the connectors (A) and remove the actuator (1).
AssemblyAssembly is the reverse order of disassembly.
ALIIA0357GB
ALIIA0358GB
MIR-21Revision: November 2012 2012 Frontier