draft - university of toronto t-space · draft an equation to ... buried pipes, failure prediction,...
TRANSCRIPT
Draft
An equation to predict maximum pipe stress incorporating
internal and external loadings on buried pipes
Journal: Canadian Geotechnical Journal
Manuscript ID cgj-2015-0500.R1
Manuscript Type: Article
Date Submitted by the Author: 08-Jan-2016
Complete List of Authors: Robert, Dilan; RMIT University, Civil, Environmental and Chemical Rajeev, Pathmanathan; Swinburne University of Technology, Civil and Construction Engineering Kodikara, Jayantha; Monash University, Rajani, Balvant; Principal Engineer, Rajani Consultants Inc,
Keyword: Buried pipes, failure prediction, stress analysis, analytical models, traffic
loads, internal water pressure, pipe corrosion
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
1
An equation to predict maximum pipe stress incorporating internal and external loadings on
buried pipes
D.J. Robert1, P. Rajeev
2, J. Kodikara
3 and B.Rajani
4
1Lecturer in Civil Engineering, School of Engineering, Civil Engineering Department, RMIT
University, VIC 3001, Australia, Tel: +61 (0) 3 9925 1908, email: [email protected]
(Formerly at Monash University)
2Senior Lecturer in Civil Engineering, Department of Civil and Construction Engineering, Swinburne
University of Technology, VIC 3122, Tel: +61 (0) 3 92144942, Australia, email:
[email protected] (Formerly at Monash University)
3Professor of Civil Engineering, Department of Civil Engineering, Monash University 3800,
Melbourne, VIC 3800, Australia, Tel: +61 (0) 3 990 54963, email: [email protected]
4 Principal Engineer, Rajani Consultants Inc, email: [email protected]
*Correspondence, E-mail: [email protected]
Abstract
Pipelines used for water and other services are very important lifelines in modern society. Commonly,
these buried pipes are subjected to significant stresses due to external (traffic and earth) and internal
(water pressure) loads. As many of these pipelines were laid some time in the last century or earlier,
in most cases their condition has deteriorated primarily by electro-chemical and/or micro-biological
corrosion. Corrosion activity (internal and external) can manifest in various forms , but in many cases
will lead to reduced pipe thickness, which in turn leads to an increase in pipe stresses induced by the
external and internal loads. Currently available analytical procedures to estimate pipe stresses are
based on over-simplifications such as the two dimensional (2-D) analysis based on Winkler springs,
limiting their application to general pipe burial conditions. This paper describes the application of a 3-
D finite element method to analyse a buried pipe subject to external and internal loads. Firstly, the
Page 1 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
2
finite element model is validated against the data from field tests conducted on the basis of a cast iron
pipe which was laid in 1930 at Strathfield, Sydney. The results of these 3-D finite element analyses
are then used to develop a closed-form expression to predict maximum stresses in pipes of different
sizes buried in different soil types. Having obtained a good agreement between the proposed model
outcomes and the 3-D FE results, the proposed model has been validated against the field test data
under different internal and external loadings. The verified outcomes of the model reveal that it can be
used to predict maximum stresses without conducting full-scale finite element analysis, which often
requires specific computational resources and computational skills. Further, the proposed model can
be used in probabilistic analyses, where a large number of calculations need to be carried out to
account for the uncertainty of the input variables. The applications of the model are also discussed in
relation to the assessment of pipe performance and remaining safe life.
Keywords: Buried Pipes, Failure Prediction, Stress Analysis, Analytical Models, Traffic Loads,
Internal Water Pressure, Pipe Corrosion, Field Tests
Page 2 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
3
1. Introduction
Pipelines used for water and other services are very important lifelines in modern society.
Commonly, these buried pipes are subjected to significant stresses due to external (traffic and earth)
and internal (water pressure) loads. As many of these pipelines were laid some time in the last
century or earlier, in most cases, their condition has deteriorated, primarily by electro-chemical and/or
micro-biological corrosion. Corrosion activity (internal and external) can manifest in various forms,
but generally leads to reductions in pipe thickness. The reduction in pipe thickness in turn leads to
increased pipe stresses due to external and internal loads. Consequently, pipe bursts have become
common and the management of these pipelines, in particular the critical large diameter pipelines, has
become a pressing issue for water authorities worldwide. In contrast to the design of a new pipeline,
the main questions here are the determination of how close a critical pipeline is to failure and the
remaining life of the pipeline. In this regard, it is necessary to use models that take into account the
internal and external factors that contribute to pipe stresses as accurately as possible.
Current practice in estimating pipe stresses is to use analytical and semi-empirical solutions such as
those developed by Spangler (1941) and Watkins and Anderson (1999). Although these solutions are
widely used in practice, the solutions involve various assumptions and limitations. For instance, three-
dimensional effects are ignored and the use of Winkler springs to analyse pipe-soil interaction is a
limitation. A more advanced approach is to solve the problem using 3-D finite element analyses to
determine the stress distribution for a pipe at hand with a specific set of both external and internal
factors. Unfortunately, this process can be very time-consuming and requires specialised skills and
resources in the computer analysis of soil/structure interactions. In the present paper, 3-D finite
element analyses are used to undertake extensive parametric studies to compute stresses generated in
buried rigid pipe. Firstly, the finite element model is validated against the data from field tests
conducted on the basis of a cast iron pipe which was laid in 1930 at Strathfield, Sydney. The results of
the validated 3-D finite element model are used to develop a closed-form solution using non-
dimensional analysis, paying due consideration to the most relevant internal and external factors. The
Page 3 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
4
solution is presented in a form suitable for pipe stress analysis that facilitates failure prediction or
remaining life estimation.
2. Current Pipe Stress Analysis
Pipes are typically designed as rigid or flexible, although this demarcation is approximate and all
pipes experience behaviour specific to these two categories to a different degree (Young and Trott
1984). For instance, a rigid pipe made of cast iron may become flexible if the pipe thickness reduces
appreciably. In this regard, the discussion below and the following development of a new equation
consider pipes generally, incorporating the general mechanics of the pipe-soil interaction.
In common terminology, rigid pipes include pipes made from stiff brittle materials such as reinforced
concrete, vitrified clay and cast iron, while flexible pipes include pipes made from less stiff ductile
materials such as steel, fibre-glass and high density polyethylene. Rigid pipes are sufficiently strong
(both within the pipe wall and joints) to withstand most anticipated external (traffic and earth) and
internal (water pressure) loads without the contribution of horizontal soil support, which is assumed to
be negligible in the design of rigid pipes. Therefore, the design of rigid pipes is mainly governed by
the ultimate yield strength or fracture toughness of the pipe material. In contrast, flexible pipes rely
upon the deformation of the pipe from imposed loads to mobilise the support of embedment materials
on both sides of the pipe. The primary structural function is distributing the imposed vertical loads to
the surrounding soil. In general, flexible pipe can deflect more than 2% without cracking. Only a
small portion of the imposed load is actually carried by the flexible pipe itself, while the majority is
transferred to the surrounding bedding material. Therefore, the design of flexible pipes relies on the
soil restraint developed as a result of the pipe deflection caused by the imposed loads. Therefore, the
design of flexible pipes is mainly controlled by either deflection or elastic buckling.
Two keys aspects of the analysis of a buried pipe are the consideration of external and internal loads
acting on the pipe and the determination of critical stresses and deformations (in the case of flexible
pipes) that the pipe experiences with respect to these loads.
2.1. Pipe stress due to external and internal loads
Page 4 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
5
The determination of pipe stress due to external and internal loading is important for the design of
new pipes and the assessment of an existing pipe. The structural design of buried pipe is based on
various criteria, such as (1) internal pressure, which may cause bursting; (2) corrosion and erosion,
which may reduce wall thickness; (3) crippling of the pipe wall or seams caused by external soil
pressure (this may be crushing or buckling of the wall); and (4) ring deflection or change in diameter
(flattening down) of the ring due to compression of the soil and traffic load (Watkins and Smith
1967).
Ring deflection can be ignored for a rigid pipe under soil and traffic load. Therefore, the pipe stress
can be computed using the elastic ring theory with an assumed soil stress distribution around the pipe
to mimic the effects of soil-structure interaction. Two different soil stress distributions are typically
assumed in rigid pipe design: (1) uniform vertical stress due to backfill and traffic load is assumed at
the pipe crown level and the invert level and no lateral support from the adjacent soil; (2) uniform
vertical stress due to soil and traffic load is assumed at the pipe crown level and the invert level and
uniform lateral stress at the sides. The lateral stress is calculated using the lateral earth pressure
coefficient. Figure 1 shows the assumed pressure distributions around a rigid pipe.
On the basis of the assumed pressure distribution shown in Fig. 1(a) (i.e., no lateral support), the
maximum bending stress in the pipe can be computed using the elastic ring theory, as given by
Watkins and Anderson (2000):
2
2
max4
5.1
t
Dq
⋅
⋅⋅=σ (1)
where, q is the uniform vertical stress due to soil and traffic loads, D is the mean pipe diameter and t
is the pipe wall thickness.
For the assumed pressure distribution shown in Fig. 1(b) (i.e., with lateral support), the maximum
bending stress in the pipe can also be computed using the elastic ring theory (Watkins and Anderson
1999) as follows:
Page 5 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
6
2
2
max4
)1(5.12 t
Dqk
t
Dqk
⋅
⋅−⋅+
⋅⋅⋅
=σ (2)
where, q is the uniform vertical stress due to soil and traffic loads and k is the lateral earth pressure
coefficient. In both the above calculations, stress q is required to be estimated using a suitable method.
The deflection of the ring is often the most important consideration in flexible pipe design and it
requires the accurate determination of stresses around the pipe due to soil and traffic loads. The
Spangler stress formula and the modified Iowa formula are typically used in the design of buried
flexible pipes. The Spangler stress formula computes the circumferential bending stress at the pipe
invert due to vertical load as follows (e.g., Masada 2000):
33 8
3
DpKtE
DtEWKσ
z
verticalb
⋅⋅⋅+⋅⋅⋅⋅⋅⋅
= (3)
where verticalW is the vertical load due to backfill and surface loads including an impact factor, E is
the pipe modulus of elasticity and P is the internal pressure. bK and zK are bending moment and
deflection parameters, respectively, that depend on the bedding angle. The appropriate values of bK
and zK can be found in Moser and Folkman (2008).
In 1941, Spangler combined the elastic ring theory and his unique "fill-load hypothesis" to establish
the original Iowa formula to estimate pipe ovality due to vertical loads. The fill-load hypothesis
comprises three elements: (1) The vertical load on a pipe may be determined by Marston's theory and
is distributed approximately uniformly over the crown pipe width; (2) The vertical reaction on the
bottom of a pipe is equal to the vertical load on the pipe and is distributed approximately uniformly
over the invert pipe width; (3) The passive horizontal pressure on the side of the pipe is distributed in
a parabolic shape over the middle 1000 of the pipe and the maximum unit pressure is equal to the
modulus of passive pressure of the side fill material multiplied by one-half of the horizontal deflection
of the pipe. The assumed stress distribution around a flexible pipe is shown in Fig. 2, as given in
Masada (2000).
Page 6 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
7
Based on the assumed stress distribution, the Iowa formula was derived as follows:
3'
3
061.0 rEEI
KrWDx zverticalL
+=∆
(4)
where x∆ is the horizontal diameter change, DL is the time lag factor, I is the moment of inertia of
pipe wall section, r is the radius of the pipe, and 'E is the modulus of passive soil resistance. The
time lag factor DL was introduced to recognize a slight increase in pipe deflections over time due to
consolidation of the soil at the sides of the pipe. The values for DL, bK and zK can be found
elsewhere (Masada 2000).
The original Spangler formula given in Eq. 3 does not include the beneficial effects of lateral soil
restraint. By combining the original Spangler formula and the Iowa formula, Warman et al. (2009)
proposed the modified Spangler equation as follows:
3'33 732.024
6
rErpKtE
rtEWKσ
z
verticalb
⋅⋅+⋅⋅⋅+⋅⋅⋅⋅⋅⋅
= (5)
For the design of the pipe, the operating/working pressure )( Wp and the surge pressure )( Sp are
added to find the design pressure. The stress due to internal pressure can be computed using Barlow’s
hoop tension formula as follows:
t
rppσ SW
p
⋅+=
)(
(6)
As stated above, the accuracy of prediction of pipe stress depends on the accurate determination of the
external and internal loads exerted on the pipe. The calculation of maximum stress for the design of
pipes subjected to external loading suffers from a number of uncertainties: (1) most of the design
methods use the Boussinesq theory to estimate the traffic load experienced by the pipe, assuming that
the loaded soil mass is homogeneous and ignoring the presence of a stiff pipe within the soil; (2) the
Spangler stress formula and the Iowa formula have somewhat inconsistent treatment of the internal
pressure stiffening and soil resistance effects; (3) stress equations are based on assumed and
Page 7 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
8
approximate soil stress distributions around the pipe; (4) the variations of soil density that can occur
in the various zones during pipe installation are not considered; (5) the demarcation of rigid and
flexible pipes is somewhat arbitrary, and all pipes experience stress distribution governed by the same
mechanics but with varying degrees of relevance; and (5) any possible slip between the pipe and the
surrounding soil is not considered. A more complete stress analysis using finite element method may
be able to reduce some of these limitations.
2.2. Failure Prediction
The current state of a buried pipe is normally assessed using the framework by Schlick (1940), where
the pipe stress can be represented as interaction curves combining the external and internal variables,
namely, the internal pressure and the external traffic load. The Schlick interaction curve is developed
on the basis of the experimental load tests conducted on cast iron pipe subjected to combined internal
pressure and uniform external three-edge loading along its length. The failure of a pipe section occurs
when the following criterion is satisfied:
1
2
>
+
cc W
W
P
P (7)
where, P is the internal pressure (i.e., SW pp + ) , Pc is the critical pressure that would cause failure in
the absence of any external loading, w is the applied external load (i.e., verticalW ) and Wc is the
external load that would cause failure with no internal pressure. Although Schlick’s experimental
work was originally conducted on cast iron water and gas pipes, the criterion in Equation 7 is used
generally to design against failure in all rigid pipeline materials (Watkins and Anderson 1999).
3. Basis for a New Pipe Stress Prediction Equation
In this section, the basis for the development of a new and improved equation, particularly for the
evaluation of maximum stress in existing buried pipes, is considered. A finite element model has been
developed to compute the pipe stress due to traffic and pressure loads. A detailed description of the
finite element model and loadings is given below.
Page 8 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
9
3.1 Finite Element Model Description
Three-dimensional (3-D) finite element analyses were carried out using ABAQUS 6.11/standard to
obtain the pipe and soil stress distribution around the pipe that were used to develop the pipe stress
prediction model. The soil was represented by 8-noded brick reduced integration elements and the
pipe was represented by 8-noded shell reduced integration elements. The behaviour of both soil and
pipe were assumed to be linear elastic, similar to what is assumed in the derivation of the available
analytical solutions. i.e., soil is assumed to be over-consolidated and behave elastically during the
range of tested traffic loads (the effects of soil plasticity studied using non-linear plasticity soil models
are reported in Section 3.3). The soil side boundaries of the FE model were assumed to be smooth and
located far (i.e., 5m) from the pipe (& traffic loads) to eliminate any boundary effects. Figure 3 shows
the mesh discretization (6,600 shell elements and 108, 000 solid elements to represent the pipe and
soil, respectively) and model dimensions. The appropriate dimensions and the mesh density of the
model were selected after a number of trials to minimise mesh and boundary effects on the calculated
pipeline stresses.
Based on the variations considered in the physical variables in Table 1, 830 3-D analyses were
conducted. In the following sections, the FE model is first validated against the data from field
experiments. Secondly, the numerical results are compared with the analytical models (i.e., the
Spangler model) in terms of soil and pipe stresses. Then, the numerical results are used to generate a
closed–form non-linear regression equation for pipe maximum tensile stress under operating
conditions of the pipe and internal/external loading conditions.
3.2 Validation of the FE model using field test data
The developed 3-D FE model was first validated using field experiments, which were conducted as a
part of an advanced condition assessment and pipe failure prediction project. A series of field tests
was conducted to investigate the behaviour of cast iron pipe under traffic loading. A decommissioned
660 mm diameter spun cast iron pipe (25mm thickness), which was laid in 1930 at Strathfield, Sydney
was selected for the investigations. The pipe and surrounding soil were instrumented with strain
Page 9 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
10
gauges and pressure pads to monitor the behaviour of the system during the applications of truck
loads and water pressure loading. Fig. 4 shows the instrumentation of the pipe used in the field test.
The pipe was instrumented by excavating pits to the required depth to expose the pipe (burial depths
were from 700mm to 1080mm at the edge and middle of the road respectively). In addition to
monitoring the pipe deformations, the response of soil was also recorded for in situ/traffic load-
induced ground pressures, moisture and temperature variations. Initially, the field tests were
conducted on the road base using different trucks moving at various speeds (stationary, 5 kmph & 15
kmph). The pipe response was secondly measured while pressurizing the water (0-700kPa) in the pipe
with the trucks being stopped and driven on the final asphalt road. A complete description of the field
test, including instrumentation and preparation, is presented in Chan et al. (2015).
A 3-D finite element model was developed in ABAQUS to simulate the field tests. The properties of
the pipe and soil used in the analysis are shown in Table 2. The cast iron and subgrade material
properties were obtained from laboratory experiments conducted at Monash University, i.e., the
stiffness of the cast iron was obtained using tensile tests conducted on coupons cut from the field test
pipe. The stiffness of the subgrade material was obtained from triaxial tests (consolidated undrained)
conducted on samples dug out from the field test bed (Fig. 5). Other properties were assumed as given
in the relevant standards (Austroads 2010). The behaviour of both pipe and soil were assumed to
follow elastic behaviour.
Firstly, the results of the test conducted using a small truck [single axle single tyre (SAST) axle load
4.85t] placed on the road base was used to validate the 3-D FE model for traffic loading on the road
base. The results were compared with field data for pipe deformation (i.e. strains & stresses) and soil
stresses. It can be seen that the FE model predicts similar strain distributions and amounts to those
observed by the strain gauges (Fig. 6(a)). This is also reflected in the circumferential stress
comparison between the FE model and the field pipe (Fig. 6(b)). The maximum difference of the
strains between the field data and FE prediction is less than 10%.
Page 10 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
11
The soil stresses above the pipe level between the FE model and field soil also show similar
distributions and amounts (maximum difference < 5%), reflecting reliable FE model predictions (Fig.
7). The initial over-burden stress of ~14kPa at the pipe level was increased to ~38kPa due to the truck
loading. However, such levels of stress increase imply only soil elastic deformations under very high
initial stiffness (100MPa for base and 8MPa for subgrade). Therefore, the assumption used in the FE
model to idealise the soil behaviour as elastic is justified.
Analyses were also conducted to simulate the simultaneous pressure loadings and traffic loadings on
the buried pipe. The tested water pressure was varied from 0-700kPa and the traffic loads were
changed by the truck loads. The results of the test conducted on the basis of a medium-sized truck
(SAST axle load 5.78t) placed on the final road were used to validate the 3-D FE model under both
pressure and traffic loading. First, the FE results were compared with the field data for water pressure
loading excluding traffic loads to investigate the model’s capability to capture the water pressure
loading. In this regard, the FE-predicted circumferential strains are compared to field-observed data in
Fig. 8 at four stages of pressurizing the pipe; 200kPa, 350kPa, 550kPa and 690kPa. It can be seen that
the FE model predictions of strain distribution and amounts are consistent with the field data at
different water pressure loadings. Second, the FE results were compared with the field data for the
scenarios of both the water pressure loading and traffic loading conditions. Similar to the pressure
loading scenario, the FE models predict realistic strain distributions and amounts when compared with
the field-observed data for traffic loading on the pressurised pipe (Fig. 9(a)). A comparison of
circumferential stress between the FE model and the values obtained from field data also shows good
agreement (Fig. 9(b)). Therefore, it is considered that the 3-D FE model used to predict the buried
pipe response under internal and external loading captures the essential mechanics of the field
problem.
3.3 Soil plasticity effect on buried water pipes
Analyses were performed using the conventional Mohr-Coulomb model to investigate the effect of
soil plasticity on buried pipeline subjected to internal and external loads. Simulations were
Page 11 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
12
conducted on the basis of a buried pipeline [cover height (H) / diameter (D) – 1.3] with a diameter and
thickness of 660mm and 15mm respectively. The pipeline was assumed to operate at 600kPa water
pressure and under varying traffic loads (i.e. tyre loads) ranging from 0-30kPa (SAST configuration).
The soil condition was simulated on the basis of subgrade soil properties derived from the field test-
bed samples. Saturated consolidated undrained triaxial tests were conducted on these samples at
confining stresses of 10kPa, 30kPa and 50kPa. Based on laboratory test data (Fig. 5), the soil
properties (effective stress-based) were obtained as 8MPa, 32.2o and 8kPa for stiffness, friction angle
and cohesion respectively. The simulations were conducted at the same initial density (18.5kN/m3)
observed in the test-bed.
The results of the elasto-plastic analysis were compared with the corresponding analysis simulating
elastic soil response. The results show that the maximum pipe circumferential stresses during pressure
loading (i.e. only water pressure) are identical for elastic and elasto-plastic analysis (Fig.10). This
response can be explained by the soil stress distribution at the top of the pipe being consistent between
the analyses. The results also reveal that the pipe maximum stress during traffic loading can be similar
for both the soil idealizations under small traffic loads (<20kN), as shown in Fig. 11. For higher
traffic loads (30kN representing a large truck load), there is less than 5% difference in the maximum
pipe stress among the different soil modelling scenarios, i.e., the maximum pipe stresses at 30kN
traffic loading are 22MPa and 21MPa for pipes buried in elastic and elasto-plastic soil respectively.
The response during traffic loading can be explained using the elementary evolutions of the stress
paths in the �-plane (in the direction of the isotropic axis) at the ground surface and at the pipe level
at traffic loads of 0kPa, 10kPa, 20kPa and 30kPa. As shown in Fig. 12, the deviatoric stress in soil at
the pipe level is hardly affected by the traffic loads, in contrast to the stresses near the ground surface,
i.e., the deviatoric stress in the soil at the pipe level changes from 21.2kPa to 22.1kPa when the traffic
load changes from 0kPa to 30kPa. Hence, the small difference of pipe maximum stress calculated
considering either the elastic or the elasto-plastic soil can be attributed to the limited increase in the
soil mean pressure at the pipe level during traffic loading.
Page 12 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
13
Considering the small difference in pipe stress prediction (<5%) between elastic and Mohr-Coulomb
soil plasticity, and the significant computation time required for Mohr-Coulomb plasticity [identical
3-D simulations using intel 12 cores 2.67GHz-128GB RAM consumed 3 hours and 12 hours for
elastic and Mohr-Coulomb analyses respectively], the analyses for the parametric study utilized linear
elastic soil response. The linear elasticity assumption used to simulate the soil behaviour can also be
justified using the comparable soil stress predictions between the FE model and actual observations in
the field (Fig. 7).
3.4 Effect of soil-pipeline interaction
A series of FE analyses were conducted to investigate the effect of interface friction between pipe and
soil. A pipeline (diameter 660mm and thickness 15mm) buried at 1.2m depth and operating at 0.6MPa
water pressure was tested for a range of traffic loadings. The interaction between the pipe and soil was
modelled on the basis of the Coulomb friction model which relates the maximum allowable frictional
shear stress ( critτ ) across the interface to the contact pressure ('
nσ ) between the pipe and soil. The
allowable frictional stress is given by '
nµσ where ( µφtan ) is the interface friction coefficient. The
contacting surfaces will stick together and the behaviour remains elastic when critττ < . The slipping
along the interface between the buried pipe and surrounding soil takes place once τ produced in the
interface reaches critτ . This behaviour was modelled using the finite movement solution available in
ABAQUS (ABAQUS, 2011).
The results of the analyses are shown in Fig. 13 for maximum circumferential stress of the pipe under
various traffic loading for different interface conditions. They reveal that the interface friction has a
negligible effect on the resulting pipe maximum stress. However, Potyondy (1961) showed that skin
friction between soil and construction material (such as steel and concrete) can be substantial and
depends on many factors such as the moisture content of soil, roughness of surface, composition of
soil and the intensity of normal loads. Considering the negligible effect of the pipe-soil interface in
Page 13 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
14
this problem, the analyses conducted in this study assume a frictionless interface, as was assumed in
developing the analytical models available for pipe stress predictions.
3.5 Evaluation of traffic load
Since traffic load has been identified as a key variable contributing to pipe stress, initially, a more
detailed treatment was given to examine how traffic load may be presented in a simplified form from
a plethora of axle and load configurations coming from a typical traffic spectrum applicable to a
paved road. Table 3 shows typical axle configurations and ranges of axle loads measured at a weigh-
in-motion (WIM) system on a highway in Victoria, Australia. One of the questions that needs to be
examined is whether we could utilise a single representative load on the surface to represent multiple
axle configurations and tyre loads. This is briefly examined using FE analysis of a typical pavement
system.
A pavement system consisting of a top asphalt layer (thickness = 240 mm, modulus = 3 GPa),
unbound base layer (thickness =100mm, and modulus = 300 MPa), and subgrade soil (deep,
modulus=50 MPa) was considered. A cast iron pipe (thickness = 8 mm, modulus = 160 GPa) with a
diameter of 660 mm buried below the pavement surface at a depth of 800 mm was considered. This
information was included in a 3-D FE model. Figure 14 shows the maximum tensile stress on the pipe
due to a range of axle configurations and tyre loads. Each tyre loading was presented as a circular
patch of loading (with a radius 92.1 mm according to Austroads (2010), and axle configurations were
presented according to general axle dimensions used for trucks. The single axle dual tyre (SADT)
with a 80 kN axle load represents the “Standard” axle used in pavement design. As can be seen from
Fig. 14, different axle and load configurations can give rise to a range of maximum pipe stresses. For
this example, the half axle loads per unit stress increase for SAST, SADT, TRDT configurations can
be calculated as 2.85.8
70 = , 9.68.5
40 = and 9.169.8
150 = , respectively. Using these scaling
factors with the assumption of linear material behaviour, the equivalent single tyre loads for the
SADT 80KN axle load can be calculated as 5.472.8*9.6
40 = (the equivalent SAST full axle load
is 0.952*5.47 = kN). Similarly, the equivalent single tyre loads for the TRDT 300KN axle load can
Page 14 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
15
be calculated as 8.722.8*9.16
150 = (the equivalent SAST full axle load is 6.1452*8.72 = kN).
Similarly, the other axle configurations can be converted to equivalent SAST and the use of a single
loading due to one tyre pressure may be appropriate for the development of a practical closed-form
stress prediction model. However, the scope of this paper is not to investigate the effect of axle load
configurations, but to study the effect of internal and external loadings in buried pipelines.
3.6 Physical variables for simplified pipe burial conditions
A series of FE analyses was conducted using the validated 3-D FE model, to investigate a simplified
closed-form equation for pipe stress prediction. Figure 15 shows a typical simplified pipe burial
condition, especially as applicable to the setting of an old buried water pipe. In old buried pipelines, in
most cases, the same native soil has been backfilled and under the present conditions, the presence of
a trench to lay the pipe is not discernible. Furthermore, some pipe design methods (e.g., AWWA
M11 1999) advocate wide trench design, where the presence of a trench is ignored. Hence, no trench
is considered in the simplified pipe setting. Furthermore, to simplify the analysis to a manageable
level, the presence of road pavement is also ignored, and it is considered that a single effective
modulus representing the pavement and soil can be used to represent the backfill condition. It should
be noted that this pipe setting may also be approximately applicable to other scenarios, including
where pipes are subjected to loading from construction machinery during pipe laying or road renewal
and where pipe is laid in a non-traffic area, and subjected to only soil loads and/or nominal traffic
loads.
The level of stress to which pipelines are subjected from traffic loads depends on soil conditions as
well as pipe properties (material, sectional and operating properties), in addition to the magnitude of
the traffic load )(W . From the soil condition perspective, soil modulus )( sE , density )(γ , lateral
earth pressure coefficient )(k and soil Poisson’s ratio )( sυ may be dominant. Pipe material modulus
and Poisson’s ratio ),( ppE ν , sectional properties such as thickness )(t and diameter )(D , and
Page 15 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
16
operating pressure )(P can also have significant control on the level of stress to which the pipe is
subjected . Eq. 8 summarises the maximum tensile stress of the pipe as a function of identified factors:
),,,,,,,,,,( htDPEkEW ppss υυγφσ = (8)
Eq. 8 consists of 11 physical variables. Based on the Buckingham � theorem, Eq. 8 can be expressed
using an expression involving a set of 9 dimensionless variables as given in Eq. 9:
)..
,,,,,,,,('..
.22
2
hD
Wk
h
E
E
P
t
D
D
h
E
E
hDW
Dps
s
ss
p
γυυ
γφ
γσ
⋅=
+ (9)
In the current study, physical variables identified in the problem have been varied within a practical
range as summarised in Table 1 to capture the pipeline stress. The range of variables considered was
also limited by the overall computational effort needed.
3.7 Comparison with current analytical models
The FE results were compared with the results from the model proposed by Spangler (Eq.5) and the
Ring models (Eqs. 1 & 2). Three cases were considered for comparison: Case 1 considered a pipe
with diameter 660 mm, wall thickness 8 mm and modulus 100 GPa, placed on stiff soil (Es = 50
MPa). Cases 2 and 3 considered the same pipe placed on soft soil (Es = 10 MPa) and very soft soil (Es
= 2 MPa), respectively. The case of very soft soil may also be used to represent situations where the
contribution of soil to pipe deformation is not certain. The tested traffic load configuration in all the
cases was SAST with a tyre load of 20kN.
Table 4 compares the pipe maximum tensile stress derived from Ring model and the Spangler model
against the results from FE analyses. Although the Spangler model predicts similar stresses compared
to FE analyses for pipe placed on stiffer soil, pipe stresses are over-predicted in soft soils by 56% and
69% for the ‘soil’ and ‘soil+traffic’ load cases respectively. On the other hand, the Ring model
heavily over-predicts the stresses from both the Spangler and FE models. In addition, the results from
the Ring model do not differentiate between stiff and soft soils.
Page 16 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
17
The main reason for the heavy over-prediction of the Ring model (Eq.1) is due to the lack of lateral
support provided in the model derivation. However, the modified Ring model (Eq.2) predicts lower
pipe stresses as a result of the incorporation of lateral earth support, but the stresses are independent
of the soil stiffness. Although the Spangler model incorporates lateral soil resistance, the model is
unable to consider re-distribution of stresses in a highly stressed pipe, for instance, when the pipe is
buried in soft soils. In other words, the three-dimensional effect of the pipe helps re-distribute the pipe
stresses in the longitudinal direction, as shown in Fig. 16. Figs. 17(a) and 17(b) show a comparison of
vertical stress distribution in soil directly above the pipe crown in longitudinal and lateral horizontal
directions. It is clear that the 3-D stress analysis shows peaking of stress under the traffic load and
decay of stress in both lateral and longitudinal directions. In contrast, the stress predicted by the
Spangler model remains constant over the pipe diameter, indicating a limitation in its assumptions.
4. New Pipe Stress Prediction Equation
The validated numerical model of the pipe-soil system was used to compute the maximum stress in
different pipe burial conditions, as given in Table 1. These conditions included a range of pipe
diameters, pipe wall thicknesses, soil conditions, traffic loads and internal pressure conditions. The
ranges of parameters were chosen so that computer run times were kept manageable. In a computer
with 12 processors (each running at 2.67GHz) and 128GB of physical memory, each parametric run
took 3-8 hours and altogether 830 runs were undertaken.
The maximum pipe tensile stress values computed from the numerical models were used to develop
the pipe stress prediction equation as a function of the non-dimensional parameter groups given in Eq.
(9) using nonlinear regression, as detailed below.
4.1. Nonlinear regression
The basic idea of nonlinear regression is to relate a response Y to a vector of predictor variables
T
kxxx ),......,( 21=x . Nonlinear regression is characterized by the fact that the prediction equation
Page 17 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
18
depends nonlinearly on one or more unknown parameters. A nonlinear regression model has the
general form of;
...., n, ifY ii 21 ),( =+= εθxi (10)
where, iY are responses, f is a known function of the covariate vector
T
ikiii xxx ),......,( 21=x and the
parameter vector T
p ) ...., , ,( 21 θθθ=θ and iε are random errors. si 'ε are usually assumed to be
uncorrelated with mean zero and constant variance. It is customary and convenient to minimize the
sum of the weighted squares of the errors between the measured responses (iY ) and the predicted
responses [ ),( θii xY ].This scalar-valued goodness-of-fit measure is called the chi-squared error
criterion )(2
θχ . If the function Y is nonlinear in the model parameters θ , then the minimisation of
2χ with respect to the parameters must be carried out iteratively. In this study, the Levenberg-
Marquardt method was used to minimise the 2χ and find appropriate model parameters (Marquardt,
1963; Levenberg, 1944).
4.2. Equation development
The stress prediction equation was developed for the pipes buried in both soft (represented by 2 MPa
modulus) and stiff soils (represented by 50 MPa modulus) subjected to traffic load and internal
pressure. A number of trials with varying success were undertaken to devise a suitable equation
relating the non-dimensional quantities. Based on both the Spangler and Schilck (1940) equations,
the following closed-form equation is proposed to compute the maximum pipe tensile stress:
+
+
+
+
⋅⋅
+
+
⋅⋅
⋅
=
+k
D
h
E
P
E
E
hD
W
D
t
hD
W
D
t
E
P
h
E
E
E
hDW
D
ss
p
ss
s
p
7654
2
3
2
212
2
76
54
3
211
1..
.
αααα
γα
γ
αγ
αγ
σ
ββ
ββ
β
ββ
(11)
It is worth noting that in Eq. 11 the maximum pipe tensile stress is explicitly given by a closed-form
expression of non-dimensional quantities on the right-hand side. In other words, if we know W and P,
Page 18 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
19
we can compute the maximum stress directly, using a calculator or a spreadsheet. Table 5 gives the
regressed model coefficients in Eq. 11. The comparison of the stresses and the errors in prediction
using the proposed equation and the numerical model is shown in Fig. 18. As the figure shows, the
proposed form of the equation is capable of predicting the stress with high accuracy (i.e., R2 = 0.99),
with maximum stress variation in the range of 5 to 10 MPa.
Independent validation of the proposed equation was carried out using the random values of
parameters at different levels. Figure 19 shows the proposed equation predictions against the
numerical model predictions.
4.3 Model verification
The proposed model was verified by comparing the predictions against the data obtained from the
field experiments. The results were compared for several incremental pressure loadings (i.e.
P=200kPa, 350kPa and 690kPa), as well as for a combination of water pressure and traffic loading
(i.e. P=523kPa & W=30kN). Figure 20 shows the maximum stresses derived from the proposed
solution compared with the field data. The stresses on the field pipe were obtained using the
circumferential and longitudinal strains derived from the strain gauges. The results show that the
proposed model is sufficiently capable of capturing the maximum pipe stress obtained on the basis of
field strains at various pressure and traffic loadings. Therefore, it is argued that the model can be used
reliably to predict the maximum pipe stress of uniform pipes subjected to operational loads of internal
water pressures (i.e. 100kPa to 600kPa) and external traffic loads (i.e. 0 to 40kN).
5.0 Parameter Sensitivity and Model Application
A sensitivity analysis was conducted to investigate the relative influence of the governing physical
variables on pipe stress. In this study, Spearman's rank correlation coefficient (Spearman, 1904),
which is a nonparametric measure of statistical dependence between two variables, was computed for
each controlling variable with the maximum pipe stress computed. The correlation coefficient
computed was normalised to find the relative contribution of each parameter on the pipe stress. Figure
21 shows the relative contribution to stress of each parameter as a percentage. From Fig. 21, it can be
Page 19 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
20
seen that the internal water pressure and pipe wall thickness have a greater influence (i.e., more than
20%) than traffic load, soil modulus, soil cover and lateral earth pressure coefficient (i.e., below
10%).
Fig. 22 shows a set of interaction curves for maximum pipe tensile stress for a range of pipe burial
conditions. The interaction curves shown by the solid lines are based on Eq. 11 and the curves shown
in dashed lines are from the 3-D numerical analyses. The closeness of the two predictions also verifies
the applicability of the proposed stress prediction equation (i.e., Eq. 11). The operating ranges shown
in these figures are chosen to reflect typical traffic loads from 0 to 150 kN, which could be considered
as a single wheel load in a single axle single tyre axle or the equivalent load from a truck load with
multiple axles and tyres. Even in a global sense, this level of traffic loading is appropriate (Rajani and
Abdel-Akher 2012). The range of water pressure is considered up to 1500 kPa, which can include
static and possible transient pressures during certain network operations such as valve closure or
pump shutdown.
One important thing to observe is the slope of the interaction curve with the pressure axis close to the
zero traffic load. As shown in Fig. 23, this gradient is less than 90 degrees or vertical at the point
where the interaction line meets the pressure axis, which is the case in the Schlick framework. When
the data used to generate the Schlick diagram were further examined, it became evident that there
were very few original data in the operating region given here. Most of the data were in the high
traffic load region, since it was much easier to fail the test pipes by increasing the vertical load in
contrast to increasing the internal pressure. Therefore, their vertical exit of the interaction lines at the
pressure axis was not properly validated. The important implication of this finding is as follows. The
dominant variable that leads to a large majority of pipe stress is the internal water pressure. However,
according the Schlick curve, the importance of increasing traffic load (from the internal pressure axis)
is not very significant, since the interaction curve is almost vertical in this region. In other words, to
obtain the same pipe stress, the internal water pressure would be almost the same even if the traffic
load increased to a significant level. However, with a lower gradient as indicated by the model
proposed (Eq. 11), the same pipe stress can be reached at lower pressures as the traffic load increases.
Page 20 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
21
In other words, the significance of the traffic load for pipe stress generation is exemplified in the
operating region, as can also be seen from the sensitivity analysis given in Fig. 21.
The possible application of the model developed is highlighted here with the aid of two examples.
Example 1: Assessment of existing pipe performance using the proposed equation
Consider a cast iron pipe 660 mm in diameter and 15 mm in thickness buried at a depth of 0.8 m. The
pipe is subjected to an estimated maximum of equivalent single 50 kN of traffic load and 900 kPa of
internal pressure, which includes a component of transient pressure. The following input parameters
are estimated: the elastic modulus of the pipe is 100 GPa and the tensile capacity is 100 MPa, the soil
density is 20 kN/m3, the soil modulus is 25MPa and the lateral earth pressure coefficient is 0.4.
Figure 24 shows the load-pressure interaction diagram for the pipe, developed from Eq. 11. Point A
denotes the pipe at the operating condition, under which the pipe experiences a maximum tensile
stress of 25.3 MPa. Of course, the pipe has excessive capacity since the failure stress is 100 MPa.
Figure 24 also shows the 100 MPa stress line and in order for the pipe to fail by increasing pressure
only, the pipe internal water pressure needs to increase by as much as 4075 kPa (marked as B).
Therefore, under the current operation conditions, this pipe is not likely to fail in the short term and
the factor of safety against failure may be given as 4075/900, which is almost 4.53. However, it
should be noted that stress concentration due to corrosion defect may raise the uniform stress, but this
aspect is not considered here.
Example 2: Assessment of remaining life of the pipe
Consider the same pipe shown in Example 2 with the associated input conditions. Assuming the
current average corrosion rate applicable to the buried environment is 0.2mm/year, what is the
remaining life of the pipe?
The maximum pipe stress is calculated for pipe thicknesses of 15 mm, 10 mm, 5 mm and 3.2 mm, as
the pipe thickness degrades with corrosion. Therefore, as the pipe thickness degrades, the maximum
pipe stress progressively increases to 25.51 MPa, 36.4 MPa, 67.0 MPa and 100 MPa respectively.
Therefore, when the pipe wall thickness reaches 3.2 mm, the maximum stress in the pipe will reach
Page 21 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
22
the ultimate strength of 100 MPa and the pipe will fail. Hence, the remaining life from the current
condition can be estimated as the time to reach a pipe thickness of 3.2 mm or 59 years (i.e., (15-
3.2)/0.2). Again, the uniform corrosion concept, which assumes the pipe wall corroded evenly around
the perimeter, is used in the calculation.
6. Conclusions
The equations currently available for the estimation of maximum stress in buried pipes were
examined, paying special attention to existing water pipe lines. Since a uniform pipe wall thickness is
considered, it is assumed that the pipe has undergone general corrosion and the condition can be
approximated by a reduced wall thickness. The results of the current stress equations were compared
with solutions obtained from 3-D finite element analyses. It was found that the current methods
generally over-predict the pipe stresses to varying degrees, depending on the simplifying assumptions
used to make the problem solvable as a statically determinate problem. Such over-estimation of stress
may mean condemning a pipe prematurely, when it has a substantial remaining life. To address the
limitations identified in these equations but develop a simplified solution for practical use by water
authorities, a new closed-form solution has been developed to compute the maximum pipe stress
using a combination of non-dimensional analysis, 3-D FE analysis and non-linear regression. The
equation is explicit, meaning that it can be directly used, using either a calculator or a spreadsheet, to
compute stresses once the main external and internal factors are estimated. The proposed equation
may be useful in probabilistic analyses where a large number of calculations need to be carried out to
account for the uncertainty of the input variables. The results of the equation can also be presented in
interaction diagrams of traffic load and internal pressure, similar to the Schlick curve used in pipe
design. The use of the new equation and the interaction diagrams in pipe stress assessment have been
demonstrated with the help of two examples. It is found that close to the pressure axis (low traffic
load region), the Schlick curve may not be highly accurate, and this observation may need to be
verified with more experimental results since there were few experimental results in this region in the
original Schlick curve development. It should also be noted that the new equation has been developed
for a range of operating conditions. Therefore, its validity outside this range needs to be checked
Page 22 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
23
further prior to its use in pipe settings outside these operating conditions. The equation is suitable to
be used in the evaluation of the remaining life of old pipes where the effects of initial trenching can be
ignored. As confirmed by many old pipe exhumations, the trenches of old pipes (prior to the 1960s)
were backfilled with the same soil and the effect of initial trenching has disappeared due to the long
burial duration.
7. Acknowledgements
This publication is an outcome from the Advanced Condition Assessment and Pipe Failure Prediction
Project funded by the Sydney Water Corporation, the Water Research Foundation of the USA,
Melbourne Water, the Water Corporation (WA), UK Water Industry Research Ltd, South Australia
Water Corporation, South East Water, Hunter Water Corporation, City West Water, Monash
University, the University of Technology, Sydney and the University of Newcastle. The research
partners are Monash University (lead), the University of Technology Sydney and the University of
Newcastle.
8. References
ABAQUS, Inc. 2011. ABAQUS V.6.7 User’s Manual, Providence, Rhode Island.
American Water Works Association. 1999. Steel Pipe – A Guide for Design and Installation. AWWA
Manual M11, 3rd Edition, US.
Austroads. 2010. Pavement Design-A Guide to the Structural Design of Road Pavements, Austroad
Inc.2010, Australia.
Levenberg, K. 1944. A Method for the Solution of Certain Non-Linear Problems in Least Squares.
The Quarterly of Applied Mathematics, 2: 164-168.
Marquardt, D.W. 1963. An algorithm for least-squares estimation of nonlinear parameters. Journal of
the Society for Industrial and Applied Mathematics, 11(2):431-441.
Masada, T. 2000. Modified Iowa Formula for Vertical Deflection of Buried Flexible Pipe, ASCE
Journal of Transportation Engineering, September/October, 2000.
Marston, A., and Anderson, A.O. 1913. The Theory of Loads on Pipes in Ditches and Tests of
Cement and Clay Drain Tile and Sewer Pipe. Bulletin 31, Iowa Engineering Experiment Station,
Ames, Iowa.
Page 23 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
24
Moser, A. P., and Folkman, S. 2008. Buried Pipe Design, Mc Graw Hill, New York.
Potyondy, J.G. 1961. Skin friction between various soils and construction materials. Geotechniques,
11(4): 339-353.
Rajani, B., and Abdel-Akher, A. 2012. Re-assessment of resistance of cast iron pipes subjected to
vertical loads and internal pressure. Engineering Structures, 45:192-212.
Schlick, W.J. 1940. Supporting strength of cast iron pipe for gas and water services. Bulletin No. 146,
Iowa Engineering Experimental Station, Ames, IA.
Spangler, M.G. 1941. The Structural Design of Flexible Pipe Culverts. Bulletin 153, Iowa
Engineering Experiment Station, Ames, Iowa.
Spearman, C. 1904. The proof and measurement of association between two things. Amer. J. Psychol.
15: 72–101.
Young, O.C., and Trott, J.J. 1984. Buried Rigid Pipes. Elsevier, London.
Warman, D.J., Hart, J.D. and Francini, R.B. 2009. Development of a pipeline surface loading
screening process and assessment of surface load dispersing methods, Report 05-44R1, Canadian
Energy Pipeline Association.
Watkins, R. K. and Anderson, L.R. 1999. Structural Mechanics of Buried Pipes, CRC Press , Taylor
& Francis Group. New York.
Watkins, R.K. and Anderson, L.R. 2000. Structural Mechanics of Buried pipes. CRC Press, New
York.
Watkins, R.K., and Smith, A.B. 1967. Ring deflection of buried pipe, Amer. Water Works
Association Journal , 59:367–378.
List of Figures
Figure 1 Assumed soil stress distributions around a rigid pipe for loose and dense sidefill (adapted
from Watkins and Anderson 2000)
Figure 2 Assumed soil stress distribution around pipe (adapted from Masada 2000), where Wc equals
Wvertical
Figure 3 Model dimensions and mesh discretization of the finite element model
Figure 4 Instrumentation on pipe section in the field test.
Figure 5 Triaxial test data based on samples from test bed soil
Figure 6 Comparison of pipe deformation and stresses between 3-D FE model and field data using a
small truck load (SAST axle load 4.85t)
Figure 7 Comparison of the soil stress at the pipe level between FE model and in the field using a
small truck load (SAST axle load 4.85t)
Figure 8 Comparison of the circumferential strain development between FE pipe model and field instrumented pipe under different water pressure loadings
Page 24 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
25
Figure 9 Comparison of (a) circumferential strain and (b) circumferential stress development between
FE pipe model and field instrumented pipe at water pressure 523kPa and 5.78t axle load (SAST)
Figure 10 Comparison of the pipe maximum circumferential stress and soil vertical stress variation
between elastic and plastic soils under water pressure loading
Figure 11 Comparison of the pipe maximum circumferential stress variation between elastic and
plastic soils under different traffic loadings
Figure 12 Stress paths of elements (a) at the ground surface (b) at the pipe level in π plane
Figure 13 Effect of interface friction between pipe and soil under various traffic load magnitudes
Figure 14 Variation of maximum tensile stress due to different axle and load configurations.
Figure 15 Typical simplified pipe burial conditions
Figure 16 Pipe circumferential (hoop) stress plotted along the pipe length
Figure 17 Vertical soil stresses plotted on top of the pipe (a) Lateral direction and (b) Longitudinal
direction
Figure 18 (a) Comparison of predictions from the numerical model and the proposed equation, (b)
errors in the prediction together with fitted normal distribution
Figure 19. Comparison of proposed equation and numerical model prediction
Figure 20. Comparison of proposed model outcomes with the field test data
Figure 21 Results of the sensitivity analysis
Figure 22 Comparison of predicted maximum stress using the proposed model and numerical model
simulation for pipe subjected to traffic load and internal pressure (k = 0.4, Ep = 100 GPa, γ = 19.13
kN/m3)
Figure 23 Schematic Schlick diagram
Figure 24 Load- pressure interaction diagram for example 1
Page 25 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
1
(a) Loose sidefill (b) Dense sidefill
Figure 1 Assumed soil stress distributions around a rigid pipe for loose and dense sidefill (revised
from Watkins and Anderson 2000)
k.q k.q
Page 26 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
2
Figure 2 Assumed soil stress distribution around pipe (revised from Masada 2000)
Figure 3 Model dimensions and mesh discretization of the finite element model
5-17 pipe
diameters
10-33 pipe diameters 10-33 pipe diameters
Subgrade
α α
100o 100
o
Page 27 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
3
Figure 5 Triaxial test data based on samples from test bed soil
120°
120°
120°
0
10
20
30
40
50
60
70
80
0 2 4 6 8 10
De
via
tor
stre
ss (
kP
a)
Axial strain (%)
Confining stress 10kPa
Confining stress 30kPa
Confining stress 50kPa
Figure 4 Instrumentation on pipe section in the field test
Page 28 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
4
(a) Pipe deformation (b) Pipe stresses
Figure 6 Comparison of pipe deformation and stresses between 3D FE model and field data using a
small truck load (SAST axle load 4.85t)
Figure 7 Comparison of the soil stress at the pipe level between FE model and in the field using a small truck load (SAST axle load 4.85t)
Page 29 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
5
-200 -150 -100 -50 0 50 100 150 200
Location (degrees)
FE model
Field data
0
0.00003
0.00006
0.00009
0.00012
0.00015
0.00018
-200 -150 -100 -50 0 50 100 150 200
Cir
cum
fere
nti
al st
rain
Location (degrees)
FE model
Field data
0
0.00003
0.00006
0.00009
0.00012
0.00015
0.00018
-200 -150 -100 -50 0 50 100 150 200
Cir
cum
fere
nti
al st
rain
Location (degrees)
FE model
Field data
-200 -150 -100 -50 0 50 100 150 200
Location (degrees)
FE model
Field data
(a) At water pressure 200kPa (b) At water pressure 350kPa
(a) At water pressure 550kPa (d) At water pressure 690kPa
Figure 8 Comparison of the circumferential strain development between FE pipe model and field instrumented pipe under different water pressures loading
Page 30 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
6
0
0.00003
0.00006
0.00009
0.00012
0.00015
0.00018
-200 -150 -100 -50 0 50 100 150 200
Cir
cum
fere
nti
al
stra
in
Location (degrees)
Field data
FE model
0
2
4
6
8
10
12
-200 -100 0 100 200
Cir
cum
fere
nti
al
stre
ss (
MP
a)
Location (degrees)
Field data
FE model
Figure 9 Comparison of the (a) circumferential strain and (b) circumferential stress development
between FE pipe model and field instrumented pipe at water pressure 523kPa and 5.78t axle load
(SAST)
(a) Pipe circumferential stress (b) Soil vertical stress
Figure 10 Comparison of the pipe maximum circumferential stress and soil vertical stress variation
between elastic and plastic soils under water pressure loading
0
5
10
15
20
25
30
-200 -100 0 100 200
Cir
cum
fere
nti
al
Str
ess
(M
Pa
)
Location around pipe (degrees)
Elastic soil
Elasto-Plastic soil
0
5
10
15
20
25
0 2 4 6 8 10
Ve
rtic
al
Str
ess
(k
Pa
)
Model Length (m)
Elastic soil
Elasto-Plastic soil
Page 31 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
7
Figure 11 Comparison of the pipe maximum circumferential stress variation between elastic and
plastic soils under different traffic loading
(a) Stress path of element at the ground surface (b) Stress path of element at the pipe level
Figure 12 Stress paths of elements (a) at the ground surface (b) at the pipe level in π plane
(a) Traffic Loading = 10kN (b) Traffic Loading = 20kN (c) Traffic Loading = 30kN
0
5
10
15
20
25
30
-200 -100 0 100 200
Cir
cum
fere
nti
al
Str
ess
(MP
a)
Location around pipe (degrees)
Elastic soil
Elasto-Plastic soil
0
5
10
15
20
25
30
-200 -100 0 100 200
Location around pipe (degrees)
Elastic soil
Elasto-Plastic soil
0
5
10
15
20
25
30
-200 -100 0 100 200
Location around pipe (degrees)
Elastic soil
Elasto-Plastic soil
100 200 300 400 500
30
210
60
240
90270
120
300
150
330
180
0
10 20 30 40 50
30
210
60
240
90270
120
300
150
330
180
0
Yield Surface – W=10kN
Yield Surface – W=20kN
Yield Surface – W=30kN
Stress Path
Page 32 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
8
Figure 13 Effect of interface friction between pipe and soil under various traffic load magnitudes
Figure 14 Variation of maximum tensile stress due to different axle and load configurations.
0
1
2
3
4
5
6
7
8
9
10
1 2 3 4 5 6
Ma
xim
um
Cir
cum
fere
nti
al
Str
ess
(MP
a)
Load Type
1=SADT – Lateral Alignment (80kN Axle Load)
2=SADT – Longitudinal Alignment (80kN Axle Load)
3=SAST – Lateral Alignment (140kN Axle Load)
4=SAST – Longitudinal Alignment (140kN Axle Load)
5=TRDT – Longitudinal Alignment (300kN Axle Load)
6=TRDT – Lateral Alignment (300kN Axle Load)
Lateral
Alignment
Longitudinal
Alignment
Pipe
Road Road
Page 33 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
9
Figure 15 Typical simplified pipe burial condition
Figure 16 Pipe circumferential (hoop) stress plotted along the pipe length
Description Symbol
Pipe diameter D
Pipe thickness t
Pipe stiffness pE
Pipe Poisson’s ratio pυ
Soil stiffness sE
Soil Poisson’s ratio sυ
Soil density γ
Soil lateral earth pressure coefficient k
Cover height h
Internal water pressure P
Traffic load W
0
5
10
15
20
25
0 2 4 6 8 10
Cir
cum
fere
nti
al
Str
ess
(M
Pa
)
Length (m)
FE model (soft Soil)
FE model (stiff Soil)
Spangler model -
soft soil
Spangler model -
hard soil
Page 34 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
10
(a) Lateral direction (b) Longitudinal direction
Figure 17 Vertical soil stresses plotted on top of the pipe (a) Lateral direction and (b) Longitudinal
direction
0
10
20
30
40
50
0 2 4 6 8 10
Length (m)
FE - Soft Soil (Es=10MPa)
FE - Stiff Soil (Es=50MPa)
Spangler Model
0
10
20
30
40
50
0 2 4 6 8 10
So
il S
tre
ss (
kP
a)
Length (m)
FE - Soft Soil (Es=10MPa)
FE - Stiff Soil (Es=50MPa)
Spangler Model
Pipe
Page 35 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
11
(a)
(b)
Figure 18 (a) Comparison of predictions from the numerical model and the proposed equation, (b)
error in the prediction together with fitted normal distribution
0
2000
4000
6000
8000
0 2000 4000 6000 8000
Proposed model prediction
Numerical model prediction
Data
1 : 1 line
R2 = 0.99
Page 36 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
12
Figure 19. Comparison of proposed equation and numerical model prediction
0
1000
2000
3000
4000
5000
0 1000 2000 3000 4000 5000
Proposed model prediction
Numerical model prediction
Data
1 : 1 line
R2 = 0.98
Page 37 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
13
(a) P=200 kPa & W=0 kN (b) P=350 kPa & W=0 kN
(c) P=690 kPa & W=0 kN (d) P=523 kPa & W=30 kN
Figure 20. Comparison of proposed model outcomes with the field test data
0
2
4
6
8
10
12
14
16
-150 -100 -50 0 50 100 150
Cir
cum
fere
nti
al
stre
ss (
MP
a)
Location (degrees)
Field data
Proposed Model Prediction
0
2
4
6
8
10
12
14
16
-150 -100 -50 0 50 100 150
Location (degrees)
0
2
4
6
8
10
12
14
16
-150 -100 -50 0 50 100 150
Cir
cum
fere
nti
al
stre
ss (
MP
a)
Location (degrees)
Field data
Proposed Model Prediction
0
2
4
6
8
10
12
14
16
-150 -100 -50 0 50 100 150Location (degrees)
Page 38 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
14
Figure 21 Results of the sensitivity analysis
0 10 20 30 40
P
t
D
Es
W
k
h
Percentage of contribution (%)
Parameters
Page 39 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
15
(a) t = 4 mm, D = 660 mm, Es = 25000 kPa,
h = 1.3 m
(b) t = 4 mm, D = 1000 mm, Es = 25000
kPa, h = 0.8 m
(c) t = 8 mm, D =660 mm, Es = 25000 kPa, h =
1.3 m
(d) t = 10 mm, D = 660 mm, Es = 50000 kPa, h =
1.3 m
Figure 22. Comparison of predicted maximum stress using the proposed model and numerical model
simulation for pipe subjected to traffic load and internal pressure (k = 0.4, Ep = 100 GPa, γ = 19.13
kN/m3)
Page 40 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
16
Figure 23 Schematic Schlick diagram
Figure 24 Load- pressure interaction diagram for example 1
0
2
4
6
8
10
12
0 2 4 6 8 10 12
Exte
rna
l lo
ad
Internal pressure0
Ve
rtic
al
lin
e
P
W
Wc
Pc
Breaking load with no internal
pressure
Combination of load and
pressure which will cause
failure
Bu
rsti
ng
pre
ssu
re
wit
h n
o e
xte
rna
l lo
ad
�� � � � � ������
Page 41 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
1
Table 1 Range of physical parameters and non-dimensionless variables
Variable Description Unit Value
Es MPa 2,4,10,25,50
Ep GPa 100
υ - 0.3
D mm 300,660,1000
t mm 4,8,10,15,27
h m 0.3,0.8,1.3,2.0
k - 0.1,0.25,0.4
P kPa 300, 500, 800, 1000, 1300,
1500
W kN 0 to75
sp EE / - 2000 to 50,000
Dh / - 0.3 to 6.67
tD / - ≈ 11 to 250
sEP / - 0 to 0.03
)/( hEs ⋅γ 53 to 8772
)/( 2 hDW ⋅⋅γ - 0 to 146.2
Table 2: Material properties used in the FE model
Description Properties
Stiffness (MPa) Poisson’s ratio Density (kg/m3)
Pipe 120000 0.3 7850
Asphalt 175 0.3 2230
Base 100 0.3 2000
Subgrade 8 0.3 1850
Page 42 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
2
Table 3 Typical axle configurations and ranges of axle loads measured at a WIM system in Victoria
(Austroads, 2010)
Axle configuration,
proportion of axles of
total
Single axle
single tyres
(SAST),
40%
Single axle
dual tyres
(SADT),
21%
Tandam axle
single tyre
(TAST)
2%
Tridam axle
dual tyres
(TRDT),
12%
Tandem axle
dual tyres
(TADT)
26%
Load range whole axle,
kN
(approx. per tyre, kN)
10 to 140
(5 to 70)
10 to180
(2.5 to 45)
10 to 200
(2.5 to 50)
10 to 340
(0.8 to 28)
10 to 320
(1.25 to 40)
Table 4 Comparison of maximum pipe tensile stresses between FE model and analytical models
Case
Maximum Pipe Tensile Stress (MPa)
Ring Model3 Spangler Model FE Model
Soil Soil +Traffic Soil Soil +
Traffic Soil
Soil +
Traffic
1 38.2 (2147%)4 / 23.21 (1265%)4 76.5 (1371%)4 / 45.41 (773%)4 2.0 (17%)4 5.2 (0%)4 1.7 5.2
2 38.2 (620%)4 / 23.21 (337%)4 76.5 (410%)4 / 45.41 (203%)4 9.0 (70%)4 23.5 (56%)4 5.3 15.0
3 38.2 (83%)4 / 23.21 (11%)4 76.5 (101%)4 / 45.41 (19%)4 30.3 (45%)4 78.4 (106%)4 16.0/
20.82 30.0/38.02
Note 1: Pipe stresses using modified Ring Model (Eq. 2)
Note 2: Pipe stresses for stiff pipe (E = 207 GPa)
Note 3: q for ring model was computed using Boussinesq’s solution
Note 4: % error compared to FE results
Page 43 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal
Draft
3
Table 5 Regressed model coefficients
Parameter 1α 2α 3α
4α
5α
6α
7α
Value 0.12 4.08 1.76E+06 7.65E+04 4.17E+06 -3.23E+07 -3.55E+07
Parameter 1β 2β 3β
4β 5β 6
β 7β
Value 0.086 0.94 0.89 0.88 0.94 -0.51 -0.71
*The coefficients were estimated using the results from the numerical analyses performed for the range of
parameters in Table 1.
Page 44 of 44
https://mc06.manuscriptcentral.com/cgj-pubs
Canadian Geotechnical Journal