dr white motors series - cross hydraulics · white motors cross hydraulics pty ltd section 10.67 dr...

WHITE MOTORS

CROSS HYDRAULICS PTY LTD SECTION 10.67

DR SERIES

Due to its case drain design, the DR Series motor is an excellent medium size motor for applications with high duty cycles or frequent direction reversals. The case drain design produces a number of benefits including reduction of pressure on the shaft seal and the ability to provide a cooling loop for the system. The case flow also lubricates the vital drive components, extending motor life. An internal drain option is also available. A laminated manifold and three zone-orbiting valve are used to produce higher overall efficiencies and more usable power. A steel faced seal in the orbiting valve also lessens the risk of the seal extruding or melting, which is possible in competitive designs.

Features

Heavy-Duty Drive Link is most durable in class and receives case flow lubrication for reduced wear and increased life.

Three-Zone Orbiting Valve precisely meters oil to produce exceptional volumetric efficiency.

Standard Case Drain increases shaft seal life by reducing pressure on seal.

Rubber Energized Steel Face Seal does not extrude or melt under high pressure or high temperature.

Three Bearing Options allow load-carrying capabilities of motor to be matched to application.

Code1216

1921

25

273346

Displacementin 3/rev

(cm3/rev)

12.4 (204)15.9 (261)

18.3 (300)21.2 (348)

22.8 (375)

28.3 (465)32.7 (536)45.6 (748)

Max SpeedRPM

� Cont.� Inter.� 470� 560� 360� 440

� 320� 380� 270� 320

� 250� 300

� 200� 240� 180� 210� 130� 150

Max FlowGPM (LPM)

� Cont.� Inter.� 25 (95)� 30 (114)� 25 (95)� 30 (114)

� 25 (95)� 30 (114)� 25 (95)� 30 (114)

� 25 (95)� 30 (114)

� 25 (95)� 30 (114)� 25 (95)� 30 (114)� 25 (95)� 30 (114)

Max Torquelb-in (Nm)

� Cont.� Inter.� *Stall� 4900 (552)� 5700 (642)� 4055 (458)� 6590 (742)� 7600 (856)� 5495 (621)

� 7450 (839)� 8600 (968)� 6685 (755)� 8600 (968)� 9800 (1103)� 7035 (795)

� 9600 (1081)� 11000 (1239)� 8135 (919)

� 9800 (1100)� 11650 (1312)� 8735 (987)� 9150 (1030)� 11300 (1272)� 8120 (918)� 9200 (1036)� 12300 (1385)� 8055 (910)

Pressure ∆PSI(∆---Bar)� Cont.� Inter.� Peak� 3000 (207)� 3500 (241)� 4000 (276)� 3000 (207)� 3500 (241)� 4000 (276)

� 3000 (207)� 3500 (241)� 4000 (276)� 3000 (207)� 3500 (241)� 4000 (276)

� 3000 (207)� 3500 (241)� 4000 (276)

� 2500 (172)� 3000 (207)� 3500 (241)� 2000 (138)� 2500 (172)� 3000 (207)� 1500 (103)� 2000 (138)� 2500 (172)

WHITE MOTORS


DRSERIES

Note: Max Flow and Max Pressure must not occur simultaneously.

Note: Performance data is typical.Performance of production units varies slightly from one motor to another.

Areas within white represent maximum motor efficiencies.

200

260

12.4 in. 3/r (204cc)

15.9 in. 3/r (261cc)Torque, lb-in (Nm)Speed, RPM

WHITE MOTORS


DRSERIES




300

350

18.3 in. 3/r (300cc)


WHITE MOTORS


DRSERIES




375

470

22.8 in. 3/r (375cc)


WHITE MOTORS


DRSERIES




540

750

32.7 in. 3/r (536cc)


WHITE MOTORS


DRSERIES

5.21 (132) Max.

.524 (13.3)

.514 (13.1)

5.45 (138) Max.

5.812 (147.6)O45o

4.999 (127.0)4.995 (126.9)

1.750 (44.5)1.746 (44.3)

.25 (6)

1.47 (37)

.21 (5)

Dim. R

3.23 (82)

3.250 (82.6)3.247 (82.5)

.06 (2).12 (3)

Seal Groove Detail

3.250 (82.6)3.247 (82.5)

.120 (3.0)

.110 (2.8)

.70 (18)

Dim. S

.06 (2).12 (3)

Seal Groove Detail

3.250 (82.6)3.247 (82.5)

.120 (3.0)

.110 (2.8)

.70 (18)

Dim. S

2.80 (71) Max.

22.5o

2.61 (66) Max.

5.35 (136) Max.

.522 (13.3)

.514 (13.1)

2.80 (71) Max.

22.5o2.61 (66) Max.

5.35 (136) Max.

.522 (13.3)

.514 (13.1)

4.187 (106.3)O

4.187 (106.3)O

4-Hole with Side Ports4-Hole with End Ports

4-Hole with End Ports

4-Hole with End Ports

4-Hole with Side Ports

4-Hole with Side Ports

W2 W8

A8A2

A4 A9

Dim. S is on page 10.73

Dim. R is on page 10.73

Housings

Wheel Mount / SAE ‘A’ Flange

WHITE MOTORS


DRSERIES

Technical

Disp. Dim. S WeightCode in (mm) lbs (kg)

200 8.19 (208) 35.0 (15,9)260 8.37 (213) 36.0 (16,3)300 8.50 (216) 36.6 (16,6)350 9.06 (230) 39.2 (17,8)375 8.75 (222) 37.8 (17,1)470 9.06 (230) 39.2 (17,8)540 9.29 (236) 40.3 (18,3)750 10.00 (254) 43.5 (19,7)

Disp. Dim. R WeightCode in (mm) lbs (kg)

200 6.53 (166) 29.6 (13,4)260 6.72 (171) 30.6 (13,9)300 6.85 (174) 32.2 (14,6)350 7.40 (188) 34.7 (15,7)375 7.10 (180) 33.4 (15,2)470 7.40 (188) 34.7 (15,7)540 7.64 (194) 35.8 (16,2)750 8.35 (212) 39.1 (17,7)

Wheel Mount

A Style Flange A Style Flange

Wheel Mount

Length and WeightTables

DR motor weights vary +/- 2 lb. (.9 kg)depending upon motor configuration.

Subtract .11 in. (3 mm) from dimension formotors using 0 or 5 endcover.



Bearing

Shaft

1,000 lbs.445 DaN

1,000 lbs.445 DaN

1,000 lbs.445 DaN

1,000 lbs.445 DaN

Shaft

Bearing

-75 -50 -25 0 25 50 75 100 125 mm

500DaN

1,000

1,500

2,000

2,500

3,000

3,500

4,000

1,000lbs

2,000

3,000

4,000

5,000

6,000

7,000

8,000

9,000

-3 -2 -1 0 1 2 3 4 5 in.

-4 -3 -2 -1 0 1 2 3 4 in.

500DaN

1,000

1,500

2,000

2,500

3,000

3,500

4,000

1,000lbs

2,000

3,000

4,000

5,000

6,000

7,000

8,000

9,000-75 -50 -25 0 25 50 75 100 mm-100

Allowable Bearing And Shaft LoadsBearing Curve: The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L10 life of 2000 hours at 100 RPM. Radial loads for speeds other than 100 RPM may be calculated using the multiplication factor table located on page 8.91.

Shaft Curve: The shaft curve represents a 3:1 safety factor based on a tensile strength of 330 kpsi.

WHITE MOTORS


DRSERIES

Shafts

10

20 21

22 02

23

121 Inch Straight

.251 (6.8)

.250 (6.4).251 (6.8).250 (6.4)

1.110 (28.2)1.101 (28.0)

.999 (25.4)

.998 (25.3)

5/16-18 UNC30o

.18 (5)

.70 (18)Min.

1.59 (40)

Dim T MountingFlange

1.020 (25.9).970 (24.6)

Max. Torque: 5,880 lb-in660 Nm 25mm Straight

1-1/4 Inch Straight

.314 (8.0)

.313 (8.0)

1.388 (35.3)1.376 (35.0)

1.33 (34)Wire Ring

.276 (7.0)

.274 (7.0)

1.250 (31.8)1.249 (31.7)

5/8-18 UNF .06 (2) Dia.Wire Ring 15o

1.475 (37.5)1.425 (36.2)

.32 (8)

.83 (21)Min.

1.90 (48)

2.14 (54)


Max. Torque: 10,600 lb-in1,200 Nm 32mm Straight

1-1/4 Inch Tapered

.314 (8.0)

.313 (7.9)

.15 (4)

.276 (7.0)

.274 (7.0)

1.250 (31.8)1.248 (31.7)

1.00-20 UNEF1:8 Taper 15o

.957 (24.3)

.907 (23.0).17 (4)

.20 (5)

.75 (19) 1.37 (35)


Max. Torque: 10,6000 lb-in1,200 Nm

14 Tooth Spline

6-B Spline

1.33 (34)Wire Ring

Note: A slotted nut is standard on thisshaft.

14 Tooth 12/24 PitchStd. ANSI B92.1-1996Spline

1.249 (31.7)1.245 (31.6)

5/8-18 UNF.06 (2) Dia.Wire Ring

15o

.83 (21)

1.60 (41)Min. Spline

1.90 (48)



Dim T ShaftCode

SAE 'A' Flange in (mm)

Setback Flange in (mm)

02 1.97 (50) 3.60 (91)12 2.21 (56) 3.84 (98)22 2.58 (66) 4.22 (107) 20 2.41 (61) 4.05 (103)23 2.42 (61) 4.06 (103)10 1.97 (50) 3.60 (91)21 2.41 (61) 4.05 (103)

.394 (10.0)

.392 (9.9).276 (7.0).274 (7.0)

1.372 (34.8)1.359 (34.5)

1.33 (34)Wire Ring

1.260 (32.0)1.259 (31.9)

M8 x 1.25 .06 (2) Dia.Wire Ring

20o

Shaft Lengths

Shaft lengths vary +/- .030 in. (.8mm)

.984 (25)

.983 (25)

M8 x 1.25

.212 (5.4)

.63 (16)Min.

1.168 (29.7)1.218 (30.9)

1.08 (27.4)1.07 (27.2)

.314 (8)

.313 (8) .2766 (7).2756 (7)

MountingFlange

Dim T

1.83 (46.5)

30o

Max. Torque: 5,617 lb-in635 Nm

.46 (12)

.63 (16)Min.

1.285 (32.6)1.235 (31.4)

1.90 (48)

2.14 (54)



Max. Torque:10,600 lb-in1,200 Nm

Dim T

1.59 (40)

MountingFlange

30o5/16-18 UNC

1.00 (25) Min. Spline

.70 (18) Min

.996 (25.3)

.992 (25.2)

.245 (6.2)

.243 (6.1)

O.810(20.6)

1.00-6-B Spline(SAE J499 Std.)

WHITE MOTORS


DRSERIES

PortingSide Ports

5

D

2

A

67

1-1/16 O-ring with 7/16 Drain 3/4 BSP.F with 1/4 Drain

1.43 (36)

4.97(126)

25o

25o

12o

Aux.View A

A

B

25o

25o

38o

Aux.View A

A

B

Auxillary ViewsView A - Case Drain Port

View B - Valve Cavity

.91 (23)

1.10 (28)

D - 10 Series/2-way Valve Cavity (7/8-14 UNF-2B)

25o

25o

12o38.5o

B

A

Aux.View A

Aux.View B

25o

25o

38.5o

B

A

Aux.View A

Aux.View B

The 5 & 2 porting options can be ordered with an internal drain and/or a relief valve cavity.

1-1/16 O-Ring with 7/16 Drain3/4 BSP.F with 1/4 Drain The 6 & 7 porting options can be ordered with an internal drain.

1.20 (30)

.90 (23)

.90 (23)

Aux.View A

13o

4.55 (116)

2.73 (69)

5.10 (130)

A

B B

38.5o

Aux.View A

WHITE MOTORS


DRSERIES

PortingEnd Ports

1 7/8 O-Ring with 7/16 Drain

4.97(126)

.90 (23)

.44 (11)

.13 (3)

1.46 (37)

.39 (10).26 (7)

A

B B

A

.90 (23)

.44 (11)

1.46 (37)

.39 (10)38.5o Aux.

View A

Aux.View B

12o

.44 (11)

1.46 (37).13 (3)

.90 (23)

.39 (10).26 (7)

A

B

D

D - 10 Series/2-way Valve Cavity (7/8-14 UNF-2B)

D

B

A

Aux.View B

12o

.44 (11)

1.46 (37)

.90 (23).39 (10)

Aux.View A

The 1 porting option can be ordered with an internal drain and/or relief valve cavity.

A B A B

DR Rotation Selection

Auxillary Views

.91 (23)

1.10 (28)

View A - Case Drain Port

View B - Relief Valve Cavity

WHITE MOTORS


DRSERIES

Code

200

260

300

350

375

470

540

750

Displacement

12.4 in3/r 204 cc

15.9 in3/r 261 cc

18.3 in3/r300 cc

21.2 in3/r348 cc

22.8 in3/r374 cc

28.3 in3/r464 cc

32.7 in3/r536 cc

45.6 in3/r748 cc

Housings

4-Hole End Ports

4-Hole Side Ports

4-Hole End Ports

4-Hole Side Ports

6-Hole End Ports

6-Hole Side Ports

Code

W2

W8

A2

A8

A4

A9

Code

OF

D

X

P*R

*R1

*R2

*R3

**Z

**Z1

**Z2

**Z3

**Z4

**Z5

**Z6

Options

No OptionsFree Turn

Internal Drain(Low Pressure)

Solid NutLock Nut

Valve Cavity1000 PSI (69 Bar)

Relief Valve Installed2000 PSI (138 Bar)

Relief Valve Installed3000 PSI (207 Bar)

Relief Valve Installed50 Pulse Sensorw/4pin Connector

50 Pulse Sensor w/Male (tower) Hsg. Weather

Pack Connector30 Pulse Sensorw/4pin Connector

30 Pulse Sensor w/Male (tower) Hsg. Weather

Pack Connector30 Pulse Sensor

w/Female (shroud) Hsg. Weather Pack Connector

100 Pulse Sensorw/4pin Connector 100 Pulse Sensor

w/Male (tower) Hsg. Weather Pack Connector

* Available with 1, 2, and 5 ports only.

** Available with A2 or A8 housing and must use MD shafts on page 16.

Code

5

2

6

7

Side Ports

Radial Ports1-1/16-12 O-ring

Radial Ports3/4-14 BSP.FParallel Ports

1-1/16-12 O-ringParallel Ports3/4-14 BSP.F

Code

1

End Ports

7/8-14 O-ring

Shafts

6-B Spline

1-1/4" Tapered

1-1/4" Straight

14 Tooth Spline

1" Straight

25mm Straight

32mm Straight

Code

02

22

20

23

10

12

21

PORTS

DISPLACEMENT

600SHAFT OPTIONSHOUSINGS

SERIES

NOTE: To complete the 3 digit housing code, a housing and port option must be entered. A side port housing option must use side port connections, and a end port housing option must use end port connections. (Example: W82 = A 4-Hole radial ported motor with 3/4" BSP.F threading)

WHITE MOTORS


DRSERIES

Disp. Dim. U WeightCode in (mm) lbs (kg)

260 9.38 (238) 35.6 (16,2)300 9.51 (242) 37.2 (16,9)350 10.06 (256) 39.7 (18,0)375 9.76 (248) 38.4 (17,4)470 10.06 (256) 39.7 (18,0)540 10.30 (262) 40.8 (18,5)750 11.01 (280) 44.1 (20,0)

A Style FlangeA Style Flange

6-Hole with Rear Ports6-Hole with Side Ports

A4A9

-75 -50 -25 0 25 50 75 100 mm-100

1,000lbs

2,000

3,000

4,000

5,000

6,000

7,000

8,000

9,000

500DaN

1,000

1,500

2,000

2,500

3,000

3,500

4,000

-4 -3 -2 -1 0 1 2 3 4 in.

4,500

10,000

Bearing

Shaft

1,000 lbs.445 DaN

1,000 lbs.445 DaN

Length and WeightTables



.522 (13.3)

.514 (13.1) 4.187 (106.3)

5.35 (136) Max.

22.5o

2.80 (71)Max. 2.61 (66)Max.

O

12(3) .06 (2)Seal Groove Detail

3.250 (82.6)3.248 (82.5)

.120 (3.0)

.110 (2.8)

.70 (18)Dim U

4.99 (127)

TechnicalAllowable Bearing And Shaft LoadsBearing Curve: The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L10 life of 2000 hours at 100 RPM. Radial loads for speeds other than 100 RPM may be calculated using the multiplication factor table located on page 8.91.


HousingsSAE ‘A’ Flange

WHITE MOTORS


DRSERIES

Shafts

.251 (6.4)

.250 (6.4)

1.110 (28.2)1.101 (28.0)

.251 (6.4)

.250 (6.4)

30o5/16-18 UNC

.999 (25.4)

.998 (25.3)

.18 (5)

.70 (18)Min.

*1.98 (50)

1.59 (40)

1.020 (25.9).970 (24.6)

MountingFlange

1.33 (34)(Wire Ring)

1.388 (35.3)1.376 (35.0)

.314 (8.0)

.313 (8.0).276 (7.0).274 (7.0)

1.250 (31.8)1.249 (31.7)

5/8-18 UNF

.32 (8)

.83 (21)Min.

*2.44 (62)

2.14 (54)

1.90 (48)

1.475 (37.5)1.425 (36.2)

MountingFlange

.06 (2) Dia.Wire Ring

15o


.394 (10.0)

.392 (10.0).276 (7.0).274 (7.0)

1.372 (34.8)1.359 (34.5)

*2.44 (62)

2.14 (54)

1.90 (48)

.46 (12)

MountingFlange

1.285 (32.6)1.235 (31.4)

20o.06 (2) Dia.Wire Ring

M8x1.25

1.260 (32.0)1.259 (31.9)

.63 (16)Min.

.15 (4)

.314 (8.0)

.313 (8.0).276 (7.0).274 (7.0)

1.250 (31.8)1.248 (31.7)

.17 (4)

.20 (5)

15o1:8 Taper1.00-20 UNEF

.75 (19) 1.37 (35)

*2.60 (66) MountingFlange

.957 (24.3)

.907 (23.0)

.245 (6.2)

.243 (6.1)

.810O

1.00-6-B Spline(SAE J499 Std.)

30o5/16-18 UNC

.996 (25.3)

.992 (25.2)

.70 (18)Min.


*1.98 (50)

1.59 (40)

MountingFlange


14 Tooth 12/24 PitchStd. ANSI B92.1-1996 Spline

1.249 (31.7)1.245 (31.6)

5/8-18 UNF


15o


1.90 (48)

*2.42 (61)

.83 (21)

MountingFlange

*Shaft lengths very +/- 0.30 in. (.8mm)

15 1 Inch Straight Ext. 07 1-1/4 Inch Straight Ext.15 1 Inch Straight Ext.

25 1-1/4 Inch Tapered

09 14 Tooth Spline03 6-B Spline

08 32mm Straight









WHITE MOTORS


DRSERIES

Code

260

300

350

375

470

540

750

Displacement

15.9 in3/r 261 cc

18.3 in3/r300 cc

21.2 in3/r348 cc

22.8 in3/r374 cc

28.3 in3/r464 cc

32.7 in3/r536 cc

45.6 in3/r748 cc

Housings

6-Hole End Ports

6-Hole Side Ports

Code

A4

A9

Code

5

2

6

7

Side Ports




Code

1

End Ports

7/8-14 O-ring

Code

25

07

09

08

03

15

Shafts

1-1/4" Tapered Ext.

1-1/4" Straight Ext.

14 Tooth Spline Ext.

32mm Straight Ext.

6-B Spline Ext.

1" Straight Ext.

PORTS

DISPLACEMENT


SERIES

NOTE: To complete the 3 digit housing code, a housing and port option must be entered. A side port housing option must use side port connections, and a end port housing option must use end port connections. (Example: A92 = A 6-Hole radial ported motor with 3/4" BSP.F threading)

Code

O

F

D

X

P

*R

*R1

*R2

*R3

Options

No Options

Free Turn


Solid Nut

Lock Nut

Valve Cavity

1000 PSI(69 Bar) ReliefValve Installed

2000 PSI(138 Bar) Relief Valve Installed


* Available with 1, 2, and 5 ports only

WHITE MOTORS


DRSERIES

Shafts

*Shaft lengths may vary by ± .030 in. (,8mm)

MountingFlange

1.500 (38,1)1.499 (38,1)

.17 (4)

1.250 (31,8)1.200 (30,5)

.75 (19)1.72 (44)

*4.57 (116)

.276 (7,0)

.274 (7,0)

.15 (3,8)

.314 (8,0)

.313 (8,0)

1.125-18 UNEF 1:8 Taper

.20 (5)


.376 (9,6)

.375 (9,5)


*4.67 (119)

.75 (19) Min.

1.499 (38,1)1.498 (38,0)

3/8-16 UNC

.40 (10)

2.67 (68)

1.671 (42,4)1.657 (42,1)

.376 (9,6)

.375 (9,5)

1.530 (38,9)1.480 (37,6)

MountingFlange


30 1-1/2 Inch Straight Max. Torque: 10,600 lb-in1200 Nm 31 1-1/2 Inch Tapered Max. Torque: 10,600 lb-in

1200 Nm

28 35mm Tapered Max. Torque: 10,600 lb-in 1200 Nm

5.21 (132) Max..524 (13,3).514 (13,1)

5.21 (132)Max.

45oØ 5.812 (147,6)

.25 (6)

4.998 (126,9)4.995 (126,8)

Dim. V

2.07 (53)

1.785 (45,3)1.775 (45,1)

.15 (3,8)

.314 (8,6)

.313 (8,0).276 (7,0).274 (7,0)

1.378 (35,0)1.358 (34,5)

M24 x 1.5 Thread

.19 (5)

.12 (3)

.87 (22)1.42 (36)

MountingFlange

.900 (22,9)

.890 (22,6)

1:10 Taper

*4.20 (107)

4-Hole with End Ports4-Hole with Side Ports

W2W8

Dimension V is on page 10.82

Housings

Wheel Mount

WHITE MOTORS


DRSERIES

Disp. Dim. V WeightCode in (mm) lbs (kg)

260 8.15 (207) 39.5 (17,9)300 8.28 (210) 40.1 (18,2)350 8.83 (224) 42.6 (19,3)375 8.53 (217) 41.2 (18,7)470 8.83 (224) 42.6 (19,3)540 9.07 (230) 43.7 (19,8)750 9.78 (248) 47.0 (21,3)

Wheel Mount

Length and Weight Tables

DR motor weights vary +/- 2 lb. (.9kg) dependingupon motor configuration.

Subtract .11 in. (3mm) from dimension for motorsusing 0 or 5 endcover.

1,000 lbs445 DaN

1,000 lbs445 DaN

Shaft

Bearing

-3 -2 -1 0 1 2 3 4 5 6 in.

500DaN

1,000

1,500

2,000

2,500

3,000

3,500

4,000

4,500

5,000

5,500

6,000

1,000lbs

2,000

3,000

4,000

5,000

6,000

7,000

8,000

9,000

10,000

11,000

12,000

13,000

14,000-75 -50 -25 0 25 50 75 100 125 150 mm

Wheel Mount

Technical

Allowable Bearing And Shaft LoadsBearing Curve: The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L10 life of 2000 hours at 100 RPM. Radial loads for speeds other than 100 RPM may be calculated using the multiplication factor table located on page 8.91.


WHITE MOTORS


DRSERIES

Housings

4-Hole End Ports

4-Hole Side Ports

Code

W2

W8

Code

5

2

6

7

Side Ports




Code

1

End Ports

7/8-14 O-ring

Code

260

300

350

375

470

540

750

Displacement

15.9 in3/r 261 cc

18.3 in3/r300 cc

21.2 in3/r348 cc

22.8 in3/r374 cc

28.3 in3/r464 cc

32.7 in3/r536 cc

45.6 in3/r748 cc

PORTS

DISPLACEMENT


SERIES

NOTE: To complete the 3 digit housing code, a housing and port option must be entered. A side port housing option must use side port connections, and a end port housing option must use end port connections. (Example: W82 = A 4-Hole radial ported motor with 3/4" BSP.F threading)

Code

O

F

D

X

*R

*R1

*R2

*R3

Options

No Options

Free Turn


Solid Nut

Valve Cavity




Shafts

1-1/2" Tapered

1-1/2" Straight

35mm Tapered

Code

31

30

28


WHITE MOTORS


DRSERIES

Housings

7.26 (184)Max.

7.67 (195)Max.

3.35 (85)Min.

7.26 (184 ) Max.

7.67 (195) Max.

1.00 (25)

.50 (13)

5.00 (127)

7.115 (180.7)7.110 (180.6)

Dim. AA

1.64 (42)

5.32 (135)Max.

5.53 (140) Max.

(2) SAE J51 4b7/16-20 Release Ports.45 (11) Min. Deep

.658 (16.7)

.648 (16.5)8.250 (209.6)O

.276 (7.0)

.274 (7.0)

.314 (8.6)

.313 (8.0)

1.499 (38.1)1.498 (38.0)

.17 (4)

.20 (5)

.75 (19)

*7.14 (181)

1.87 (47)MountingFlange

1.250 (31.8)1.200 (30.5)

1:8 Taper

1.125-18 UNEFSlotted Hex NutTorque To 300-400Ft. Lbs.


Note: Shaft lengths vary+/- .030 (.8mm)


31 1-1/2 Inch Tapered

4-Hole with End Ports 4-Hole with Side PortsW2 W8

.320 (8.1)

.309 (7.9)

1.04 (26) Min.

.15 (4)

Length and Weight Tables

Disp.Code

Dim. AAin (mm)

Weightlbs (kg)

200 4.22 (107) 58.4 (26.5)260 4.41 (112) 59.4 (26.9)300 4.54 (115) 60.0 (27.2)350 5.09 (129) 62.5 (28.3)375 4.79 (122) 61.1 (27.7)470 5.09 (129) 62.5 (28.3)540 5.33 (135) 63.6 (28.8)750 6.04 (153) 66.9 (30.3)

DR motor weights vary +/- 2 lb (.9kg) depending upon motorconfiguration.

Subtract .11 in. (3mm) from dimension for motors using 0 or 5 endcover.

CAUTION: It is vital that all operating recommendations on page 10.85 be followed. Failure to do so could result in injury or death.

WHITE MOTORS


DRSERIES

Operating Recommendations

CAUTION! - White Hydraulics motors/brakes are intended to operate as static or parking brakes. System circuitry must be designed to bring the load to a stop before applying the brake.

CAUTION! - Because it is possible for some large displacement motors to overpower the brake, it is critical that the maximum system pressure be limited for these applications. Failure to do so could cause serious injury or death. When choosing a motor/brake for an application, consult the performance chart for the series and displacement chosen for the application to verify that the maximum operating pressure of the system will not allow the motor to produce more torque than the maximum rating of the brake. Also, it is vital that the system relief be set low enough to ensure that the motor is not able to overpower the brake.

To ensure proper operation of the brake, case drain back pressure must be maintained at 500 psi or less. Case drain back pressure above 500 psi can result in erratic operation of the brake. To avoid potential problems with the operation of the brake, a separate case drain line is recommended. Use of the internal drain option is not recommended due to the possibility of return line pressure spikes. A simple schematic of a system utilizing a motor/brake is shown in Figure A below.

Although maximum brake release pressure may be used for an application, a 500 psi pressure reducing valve is recommended to promote maximum life for the brake release piston seals.

To achieve proper brake release operation, it is necessary to bleed the release line and brake release cavity once all connections are made. To facilitate this operation, all motor/brake feature two release ports. One or both of these ports may be used to release the brake in the unit. Motor/brakes should be configured so that the release ports are near the top of the unit in the installed position. Once all system connections are made, one release port must be opened to atmosphere and the brake release line carefully charged with fluid until all air is removed from the line and motor/brake release cavity. When this has been accomplished the port plug or secondary release line must be reinstalled.

In the event of a pump or battery failure, an external pressure source may be connected to the brake release bleed port to release the brake, allowing the machine to be moved.

Figure A

Typical motor/brake schematic

WHITE MOTORS


DRSERIES

Technical

Allowable Bearing And Shaft LoadsBearing Curve: The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L10 life of 2000 hours at 100 RPM. Radial loads for speeds other than 100 RPM may be calculated using the multiplication factor table.


-1 0 1 2 3 4 5 6 7 8 9 in.

500DaN

1,000

1,500

2,000

2,500

3,000

3,500

4,000

4,500

1,000lbs

2,000

3,000

4,000

5,000

6,000

7,000

8,000

9,000

10,000

11,000

12,000-25 0 25 50 75 100 125 150 175 200 250 mm

Bearing

Shaft

1,000 lbs.445 DaN

1,000 lbs.445 DaN

Code

200

260

300

350

375

470

540

Displacement

12.4 in3/r 204 cc

15.9 in3/r261 cc

18.3 in3/r300 cc

21.2 in3/r348 cc

22.8 in3/r374 cc

28.3 in3/r464 cc

32.7 in3/r536 cc

Housings

4-Hole End Ports

4-Hole Side Ports

Code

W2

W8

Code

5

2

6

7

Side Ports

Radial Ports1-1/16" O-Ring

Radial Ports 3/4" BSP.FParallel Ports

1-1/16" O-RingParallel Ports 3/4" BSP.F

Code

1

End Ports

7/8" O-Ring

Code

31

Shafts

1-1/2" Tapered

PORTS

DISPLACEMENT


SERIES

NOTE: To complete the 3 digit housing code, a housing and port option must be entered. A side port housing option must use side port connections, and a end port housing option must use end port connections. (Example: W82 = A 4-Hole radial por tedmotor with 3/4" BSP.F threading)

Code

O

F

X

*R

*R1

*R2

*R3

Options

No Options

Free Turn

Solid Nut

Valve Cavity





750 45.6 in 3/r 748 cc

Operating Specifications

Rated brake torque: ...............................14,000 lb-in (1,582 Nm)Initial release pressure .......................................275 psi (19 bar)Full release pressure ..........................................475 psi (33 bar)Maximum release pressure ...........................3,000 psi (207 bar)Release volume .......................................8 - 10 cu.in. (13-16 cc)

Bearing Load Multiplication Factor Table

RPM Multiplication Factor50 1.23

100 1.00200 0.81300 0.72400 0.66500 0.62600 0.58700 0.56800 0.50

WHITE MOTORS

CROSS HYDRAULICS PTY LTD GREEN CATALOGUE

DRSERIES

DR (612) Series

NOTE: Due to the special tools, fixtures and test equipment required to properly service the brakeportion of this product, it is highly recommended that all motor/brakes be returned to the factory forrepair. White Hydraulics accepts no responsibility for repairs performed by anyone other than WhiteHydraulics factory service personnel. To inquire about repairs and obtain return authorization for aproduct, please contact the technical support department at (03) 9544 5155.

WHITE MOTORS


DRSERIES

STIKSUOENALLECSIM057666007TIKLAES

DUST SEAL SHAFT BEARING (1 PER KIT))22(SGNIPMATS&SKSIDNOITCIRFMIHSPUKCABLATEM

NOTSIPLAESPUKCABNOLFET)TIKREP52(SGNIRPSLAESTFAHS

)TIKREP3(SMIHSRECAPSLAESGNIR-OLLAMS)TIKREP8(SWERCSPACLAESNOLFETLLAMS

RECAPSKNILEVIRDLAESGNIR-OEGRALDLOFINAMLAESNOLFETEGRAL

LBMESSAROTATUMMOCLAESGNIR-O YNOTSIPREVOCDNE)3(SLAESYDOB

GNIRPSNOTSIPLAESDLOFINAMEVLAVFEILERISP0001LAESROTATUMMOCEVLAVFEILERISP0002LAESGNIR-ONOTSIPEVLAVFEILERISP0003LAESNOLFETNOTSIP

1.125-18 UNEF SLOTTED HEX NUT1.125-18 UNEF SOLID HEX NUT

ROTORS, DRIVE LINKS, AND BOLTSWHEN CHANGING MOTOR DISPLACEMENTS, A MATCHING ROTOR, DRIVE LINK AND BOLT SET KIT MUST BE ORDERED.

HOUSING KITS (EXPLODED VIEW ITEM #'S 15 & 23)

#W2& W8- DR SETBACK BRAKE (EXPLODED VIEW ITEM #15)REAR HOUSING (EXPLODED VIEW ITEM #23)

SHAFTS AND RELATED COMPONENTS KITSSHAFT KITS COME WITH RELATED SHAFT COMPONENTS (i.e. keys, nuts, etc.)TO ORDER INDIVIDUAL SHAFT COMPONENTS (i.e. keys, nuts, bolts, washers or wire rings) USE THE KIT NUMBER FOR EACH INDIVIDUAL PART.

ENDCOVER KITS (EXPLODED VIEW ITEM #32)ENDCOVER KITS COME ASSEMBLED WITH EXPLODED VIEW ITEMS # 13, 14, 30 & 31.TO ORDER A RELIEF VALVE FOR THE VALVE CAVITY ENDCOVERS, SEE THE MISCELLANEOUS KITS LISTING ABOVE FOR RELIEF VALVE KIT #'S.

#1- 7/8" O-RING REAR PORTS#5- 1-1/16" O-RING RADIAL PORTS#2- 3/4" BSP.F RADIAL PORTS#6- 1-1/16" O-RING PARALLEL PORTS#7- 3/4" BSP.F PARALLEL PORTS

700160000R

500011218 300339105 SEE MISC. KITSNUT KITDESCRIPTION SHAFT KIT KEY KIT

500753005300753005074110704005500704005045

EXPLODED VIEW ITEM #

300

110703005500703005573

500247011

BOLT SET KIT200

DISPLACEMENT

260

STANDARD ROTOR KIT FREETURN ROTOR KIT DRIVE LINK KIT

500227004600140012600140016

627272#METIWEIVDEDOLPXE

700018038

34

37

NOT SHOWNNOT SHOWN

37700018054

NOT SHOWN13 500018231

50001822114

9

12

2910 3011 31

8 28500018075700668002

6 247006667507 25

910018011500018232

3 ITEMS #1-14INCLUDED IN

SEAL KIT

204 215 22

1 162 17-19

400702005000702005053

500167004500227000500247005

500167011

DR (612) SERIES BRAKE MOTOR COMPONENTS

DESCRIPTIONEXP.VIEW

ITEM #NOITPIRCSEDTIK

EXP. VIEWITEM #

KIT

700018088910018014300018068200018074

700668003700668004700018046500018228

700664012700664019700664025

820466007520041006

600140019600140027

TIKGNISUOHNOITPIRCSED

640041006110706005500706005057

#30- 1-1/2" STRAIGHT

700160008

DESCRIPTION STANDARD ENDCOVER

700160000

500011308 500449102

700160005

600140033

300130054500013067

700665028

700665028

700665046700665033

600140027

700160009 ---700160008R700160007R

35 36 37

700160005R

ABOVE#31- 1-1/2" TAPERED

700160007

VALVE CAVITYENDCOVER KIT

WHITE MOTORS


DRSERIES

WHITE MOTORS


DRSERIES


DUST SEAL REAR THRUST BEARINGSPLIT WIRE RING FRONT HOUSING BEARING (1" WIDEMETAL BACKUP SHIM REAR HOUSING BEARING (.5" WIDEHIGH PRESSURE SEAL DIVIDER PLATEMETAL BACKUP SHIM MANIFOLD

LBMESSAROTATUMMOCLAESEDIMAYLOP YSHAFT SEAL ENDCOVER PISTONREAR HOUSING SEAL PISTON SPRINGBODY SEALS (3) FRONT THRUST BEARINGMANIFOLD SEAL 1000 PSI RELIEF VALVECOMMUTATOR SEAL 2000 PSI RELIEF VALVEO-RING SEAL 3000 PSI RELIEF VALVETEFLON BACKUP SEAL 7/8" O-RING PORT PLUG

1.00-20 UNEF SLOTTED NUTSEAL CARRIER 1.00-20 UNEF SOLID NUTTHRUST WASHER 1.00-20 UNEF LOCK NUT

ROTORS, DRIVE LINKS, AND BOLTSWHEN CHANGING MOTOR DISPLACEMENTS, A MATCHING ROTOR, DRIVE LINK AND BOLT SET KIT MUST BE ORDERE

HOUSING KITS (EXPLODED VIEW ITEM #18)STANDARD HOUSING KITS INCLUDE THE FRONT BEARING (#17) AND THE REAR BEARING (#19) INSTALLED IN THE HOUSIN

#W2 & W8- WHEEL MOUNT FLANGE#A2 & A8- 4-HOLE SAE "A" STYLE#K2 & K8- WHEEL MOUNT WITH BRAKE MOUNT#A0 & A7- 2-HOLE SAE "A" STYLE#A4 & A9- 6-HOLE SAE "A" STYLE*NOTE- ALL HOUSINGS REQUIRE THE USE OF (27/8" O-RING PORT PLUGS- SEE MISC. KITS ABOVEFOR KIT NUMBER.

SHAFTS AND RELATED COMPONENTS KITSSHAFT KITS COME WITH RELATED SHAFT COMPONENTS (i.e. keys, nuts, etcTO ORDER INDIVIDUAL SHAFT COMPONENTS (i.e. keys, nuts, bolts, washers or wire rings) USE THE KIT NUMBER FOR EACH INDIVIDUAL PAR

#02- 6-B SPLINE#22- 1-1/4" TAPERED#20- 1-1/4" STRAIGHT#23- 14 TOOTH SPLINE#06- 1" STRAIGHT#12- 25MM STRAIGHT#24- 19 TOOTH SPLINE#21- 32MM STRAIGHT

ENDCOVER KITS (EXPLODED VIEW ITEM #27)ENDCOVER KITS COME ASSEMBLED WITH EXPLODED VIEW ITEMS # 12, 13, 25 & 26TO ORDER A RELIEF VALVE FOR THE VALVE CAVITY ENDCOVERS, SEE THE MISCELLANEOUS KITS LISTING ABOVE FOR RELIEF VALVE KIT #

#1- 7/8" O-RING REAR PORTS#3- MANIFOLD PORTS, D-SHAPED#5- 1-1/16" O-RING RADIAL PORTS#2- 3/4" BSP.F RADIAL PORTS#6- 1-1/16" O-RING PARALLEL PORTS#7- 3/4" BSP.F PARALLEL PORTS

1415

123456

910

78

EXPLODED VIEW ITEM #

DESCRIPTION

EXPLODED VIEW ITEM #DISPLACEMENT

111213

DESCRIPTION

STANDARDENDCOVER KIT

30SHAFT KIT

31KEY KIT

---

500011600500011300500011200

DESCRIPTIONVALVE CAVITYENDCOVER KIT

700160008R---

NOT SHOWN

SEE MISC.

NUT KIT

16171921

DR (600) SERIES MOTOR COMPONENTS

KITDESCRIPTIONEXP.VIEW

ITEM #EXP. VIEW

ITEM #KITDESCRIPTION

500018252500018228500018231500018221

INTERNAL DRAINENDCOVER KIT

VALVE CAVITY & INTERNALDRAIN ENDCOVER KIT

NOT SHOWN

---------

34WIRE RING KIT

600140046

ITEMS #1-13INCLUDED IN

SEAL KIT

BOLT KIT

NOT SHOWNNOT SHOWN

NOT SHOWNNOT SHOWNNOT SHOWNNOT SHOWN

32

2324

WASHER KIT

252635

29BOLT SET KIT

600140027600140033

700668002700668003700668004700018046

375470540750

FREETURN ROTOR KIT DRIVE LINK KIT2022

500444003

600555000


SEAL KIT

600140025

700665046

33

500307011500357005500407011

350

260300

22STANDARD ROTOR KIT

00761005002 4500227000500247005500207000

500018059500018003500018002

700018021500449304500449303

300339303P

500167011500227004

500012004

500247011500207004

600140012600140016600140019600140027

700664012700664019700664025700665028700664028700665028700665033

500130723HOUSING KIT

500607005 500607011

500307005500357003500407005

500130823500131123500131623500131823

---500449101500449102

---500449301

---

---

500011203

500449100500449104

---500449103

500011101500011201

---

------

500449302---------------

------

500449201500449201

------

500449201500449201

700160008700160009

KITS LISTABOVE

700160000---

700160000R---

500011109500011102

700160005R700160007R

700160005700160007

700160000D700160003D700160005D700160007D

------

700160000DR---

700160005DR700160007DR

------

WHITE MOTORS


DRSERIES

DR (640) Series

29

27

28

26

23

2221

20

16

19

43 181742

40

1

39

3837

3612

1110

32

31

9

913

3534

33

14

3

6

57

4

2

41

45

4647

48

30

8

24

15

44

25

24

WHITE MOTORS


DRSERIES


DUTSLAESEGNALFWIRE RING LUG NUT

SWERCSPAC)4(MIHSPUKCABLATEMEGNALFLEEHWLAESERUSSERPHGIHGNIRAEBMM521MIHSPUKCABLATEM

RECAPSGNIRAEBLAESPUKCABNOLFETSHAFT SEAL THRUST RING

BUHGNIRAEBLAESGNISUOHRAERGNIRAEBTSURHT)3(SLAESYDOB

GNIRAEBGNISUOHRAERLAESDLOFINAMDUTSTNUOMYRATENALPLAESROTATUMMOC

TUNGNITNUOMLAESGNIR-OETALPREDIVIDLAESPUKCABNOLFET

DLOFINAMTEKSAGREPAPCOMMUTATOR ASSEMBLY

NOTSIPREVOCDNEREIRRACLAESGNIRPSNOTSIPREHSAWTSURHT

DRIVER COVER SCREWS (6)DRIVER COVERDRIVERWARN HUB ASSEMBLY7/8" O-RING PORT PLUG

ROTORS, DRIVE LINKS, AND BOLTSWHEN CHANGING MOTOR DISPLACEMENTS, A MATCHING ROTOR, DRIVE LINK AND BOLT SET KIT MUST BE ORDERED

HOUSING KITS (EXPLODED VIEW ITEM #28)STANDARD HOUSING KITS INCLUDE REAR BEARING (#25) INSTALLED IN THE HOUSING.

#W2 & W8- SETBACK W/ 7/8" O-RING

*NOTE- ALL HOUSINGS REQUIRE THEUSE OF (2) 7/8" O-RING PORT PLUGS-SEE MISC. KITS ABOVE FORKIT NUMBER.

INTERNAL SHAFTSHAFT KITS COME WITH RELATED SHAFT COMPONENTS (i.e. keys, nuts, etc.)

#24- 19 TOOTH SPLINED

ENDCOVER KITS (EXPLODED VIEW ITEM #37)ENDCOVER KITS COME ASSEMBLED WITH EXPLODED VIEW ITEMS # 12, 13, 35 & 36.TO ORDER A RELIEF VALVE FOR THE RELIEF PORT ENDCOVERS, SEE THE MISCELLANEOUS KITS LISTING ABOVE FOR RELIEF VALVE KIT #'S.

#1- 7/8" O-RING REAR PORTS#3- MANIFOLD PORTS, D-SHAPED#5- 1-1/16" O-RING RADIAL PORTS#2- 3/4" BSP.F RADIAL PORTS#6- 1-1/16" O-RING PARALLEL PORTS#7- 3/4" BSP.F PARALLEL PORTS ---

------R800061007800061007------900061007

RD700061007D700061007R700061007700061007

500011102

700160000 700160000R 700160000D

DESCRIPTIONSTANDARD

ENDCOVER KITRELIEF PORT

ENDCOVER KITSHUTTLE VALVEENDCOVER KIT


DESCRIPTIONEXP.VIEW


EXP. VIEWITEM #

KIT

1 162 173 ITEMS #1-13,42

INCLUDED INSEAL KIT

184 195 206 217 22

500018059500018002

11

5000180625000130558 23

9 2410 25

2612 27

700668003

500018080500018112

700668004

500012004700668002

13 3142 33

345351-41#SMETI4163NIDEDULCNI51

41 70001800158081000504TIKLAES

4344 - 47

500018179500018099

NOT SHOWN


700018021

350

260

BOLT SET KIT200

DISPLACEMENT STANDARD ROTOR KIT FREETURN ROTOR KIT DRIVE LINK KIT110761005400761005

820466007520041006110703005500703005573820566007720041006500753005300753005074330566007330041006110704005500704005045640566007640041006110706005500706005057

TIKGNISUOHNOITPIRCSED500131023

EXPLODED VIEW ITEM # 29DESCRIPTION SHAFT KIT

RELIEF PORT & SHUTTLE VALVEENDCOVER KIT700160000DR

D300061007------700160005 700160005R 700160005D

---700160005DR

210466007210041006910466007610041006400722005000722005520466007910041006110742005500742005003820566007720041006400702005000702005

PT666252

500444003

500018081500018151500018086500013035500018095500018194

700018046

WHITE MOTORS


DRSERIES

WHITE MOTORS


DRSERIES


DUST SEAL RETAINING SNAP RINGSPLIT WIRE RING 72MM BEARINGMETAL BACKUP SHIM THRUST BEARINGHIGH PRESSURE SEAL REAR HOUSING BEARINGMETAL BACKUP SHIM DIVIDER PLATE

LOFINAMLAESPUKCABNOLFET DSHAFT SEAL COMMUTATOR ASSEMBLYHOUSING SEAL ENDCOVER PISTONBODY SEALS (3) PISTON SPRINGMANIFOLD SEAL 1000 PSI RELIEF VALVECOMMUTATOR SEAL 2000 PSI RELIEF VALVEO-RING SEAL 3000 PSI RELIEF VALVETEFLON BACKUP SEAL 7/8" O-RING PORT PLUG

1.00-20 UNEF SLOTTED NUTSEAL CARRIER 1.00-20 UNEF SOLID NUTTHRUST WASHER 1.00-20 UNEF PACK NUT


HOUSING KITS (EXPLODED VIEW ITEM #19)

#W2 & W8- WHEEL MOUNT FLANGE#A4 & A9- 6-HOLE SAE "A" STYLE

*NOTE- ALL HOUSINGS REQUIRE THE USE OF (27/8" O-RING PORT PLUGS- SEE MISC. KITS ABOVEFOR KIT NUMBER.


#22- 1-1/4" TAPERED#20- 1-1/4" STRAIGHT#23- 14 TOOTH SPLINE#08- 32MM STRAIGHT#03- 6-B SPLINE#15- 1" STRAIGHT

ENDCOVER KITS (EXPLODED VIEW ITEM #28)ENDCOVER KITS COME ASSEMBLED WITH EXPLODED VIEW ITEMS # 12, 13, 26 & 27TO ORDER A RELIEF VALVE FOR THE VALVE CAVITY ENDCOVERS, SEE THE MISCELLANEOUS KITS LISTING ABOVE FOR RELIEF VALVE KIT #


700160005 700160005R 700160005D

700160008 700160008R ---


------

---700160007DR700160007D

DESCRIPTION STANDARD ENDCOVERVALVE CAVITYENDCOVER KIT


---SEE MISC.

BOLT KIT WASHER KITNOT SHOWN NOT SHOWN NOT SHOWN

TIKGNIRERIWTIKTUNTIKYEKTIKTFAHSNOITPIRCSEDEXPLODED VIEW ITEM # 31 32 33

700665046

TIKGNISUOHNOITPIRCSED500130928

00706005057 5 40041006110706005 6

STANDARD HOUSING KITS INCLUDE THE FRONT BEARING (#17), REAR BEARING (#20), RETAINING RING (#16), & DUST SEAL(#INSTALLED IN THE HOUSING.

600140019

70066502800704005045 5 30041006110704005 3 70066503300753005074 3 500357005

600140012

700664025

00703005573 5 20041006110703005 5 700664028

00742005003 5 500247011

DRIVE LINK KIT700664012

00722005062 0 500227004 600140016 70066401900761005002 4

21

500167011

500444003

30BOLT SET KITDISPLACEMENT STANDARD ROTOR KIT FREETURN ROTOR KIT


SEAL KIT


NOT SHOWN14 NOT SHOWN15 NOT SHOWN

12 NOT SHOWN13 NOT SHOWN

9 2710 NOT SHOWN11 NOT SHOWN

8 26700668003700668004

6 246005550007 25

2 173 ITEMS #1-13

INCLUDED INSEAL KIT

184 205 22


DESCRIPTIONEXP.VIEW


EXP. VIEWITEM #

KIT

1 16

600140027 700665028

500018059500018002500012004700668002

700018046500018228

---------

500011101 --- KITS LIST ---

700160000 700160000R 700160000D

00702005053 0 500207004

600140027

500135228

300061007------ D ---

500018141500018098

700160009 ---------

700160005DR700160007 700160007R

700160000DR

500018231500018221700018021500449304500449303

300339303P

500449302500011300 ------101944005

500449201500449201

500011200 500449102 500449301

500449201------

------ABOVE500011205

500011602500011206

500449103---

500449100

WHITE MOTORS


DRSERIES

WHITE MOTORS


DRSERIES


DUST SEAL RETAINING SNAP RINGHIGH PRESSURE SEAL SEAL CARRIERMETAL BACKUP SHIM 1.5" BEARING

ECAPSGNIRAEBLAESPUKCABNOLFET RSHAFT SEAL THRUST WASHERREAR HOUSING SEAL FRONT THRUST BEARINGBODY SEALS (3) REAR HOUSING BEARINGMANIFOLD SEAL REAR THRUST BEARINGCOMMUTATOR SEAL DIVIDER PLATEO-RING SEAL MANIFOLDTEFLON BACKUP SEAL COMMUTATOR ASSEMBLY

ENDCOVER PISTONPISTON SPRING7/8" O-RING PORT PLUG1000 PSI RELIEF VALVE2000 PSI RELIEF VALVE3000 PSI RELIEF VALVE1.00-20 UNEF SLOTTED NUT1.00-20 UNEF SOLID NUT1.00-20 UNEF PACK NUT1.125-18 UNEF SLOTTED NUT1.125-18 UNEF SOLID NUTM24 X 1.5 SLOTTED HEX NUT (#46


HOUSING KITS (EXPLODED VIEW ITEM #18)STANDARD HOUSING KITS INCLUDE THE REAR BEARING (#19) INSTALLED IN THE HOUSING

#W2 & W8- WHEEL MOUNT

*NOTE- THIS HOUSING REQUIRES THEUSE OF (2) 7/8" O-RING PORT PLUGS-SEE MISC. KITS ABOVE FORKIT NUMBER.


#31- 1-1/2" TAPERED#22- 1-1/4" TAPERED#30- 1-1/2" STRAIGHT#28- 35MM TAPERED

ENDCOVER KITS (EXPLODED VIEW ITEM #28)ENDCOVER KITS COME ASSEMBLED WITH EXPLODED VIEW ITEMS # 10, 11, 26 & 27TO ORDER A RELIEF VALVE FOR THE VALVE CAVITY RELIEF PORT ENDCOVERS, SEE THE MISCELLANEOUS KITS LISTING ABOVE FOR RELIEF VALVE KIT #


NOT SHOWN

---

33

ABOVE

SEE MISC.

33

WIRE RING KIT33

10

700160009 ------


700160005 700160005R 700160005D---

11

56

TIKGNISUOHNOITPIRCSED

EXPLODED VIEW ITEM # 31

700160003D ---

DESCRIPTIONSTANDARD

ENDCOVER KITVALVE CAVITYENDCOVER KIT


700160000 700160000R 700160000D 700160000DR

DESCRIPTION SHAFT KIT KEY KIT NUT KIT

300339105500449104

---

500449200---

32

70066503300706005057 5 40041006110706005 600704005045 5 30041006110704005 3

700665046

600140019 700664025

37500753005074 3 500357005 600140027 700665028

600140027 700665028

26000742005003 5 500247011

21

00761005002 4 10041006110761005 2

33

30DISPLACEMENT STANDARD ROTOR KIT FREETURN ROTOR KIT DRIVE LINK KIT BOLT SET KIT


500449304500449303

NOT SHOWN3333

NOT SHOWN500018221

27NOT SHOWNNOT SHOWN

26

1516

1920

24

717

22


SEAL KIT600555100

2 133 144

89


DESCRIPTIONEXP.VIEW


EXP. VIEWITEM #

KIT

33

25

00702005053 0 500207004

1 12 500018249500018238500018242500018248700018041700018033700018012500018059500012004700668002700668003700668004700018046700018021500018228500018231

300339303P700018038700018054500449306

700664012500227000 500227004 600140016 700664019

500307005 20041006110703005 5 700664028

700160005DR700160007 700160007R 700160007D 700160007DR700160008 700160008R ------

---

500136728

500011300 500449101 KITS LIST ---500011216

500011218500011310

500449105

dr white motors series - cross hydraulics · white motors cross hydraulics pty ltd section 10.67 dr...

Documents