dprtool

8/20/2019 dprtool

http://slidepdf.com/reader/full/dprtool 1/6615131

Installation Instructions

© 2008 DELACAMP. All rights reserved. DELACAMP is a distributor of compatible replacement parts and products for imaging equipment. None of DELACAMP's products are

genuine OEM replacement parts and no affiliation or sponsorship is to be implied between DELACAMP and any OEM.

Drum Pin Removal Tool Article no. 61513Patent Pending

Please read the instructions carefully before using the tool.

List of Printers:

HP CLJ 3000 Series:

HP CLJ 3000, 3500, 3600,

3700, 3800

HP CLJ CP3505

HP CLJ 4700 Series:

HP CLJ 4700, 4730

HP CLJ CP4005

Supplies & Tools:

White grease

Lint-free cloth

AlcoholNeedle nose pliers

Article no. 61513

(see photo 1)

Photo 1

Photo 2

Photo 3

Photo 4

Photo 5

NOTE: To prolong the life of your DRPINTOOL2, apply a small

amount of white grease on the tool shaft thread before using it.

Store the tool in a clean place. If the tool is dirty or contaminat-

ed with toner, clean it with alcohol. Apply a small amount of

fresh white grease on the shaft thread.

FOR USE WITH HP4700 SERIES CARTRIDGES

DRUM PIN EXTRACTION

Step 1

Release drum shutter for unobstructed access to the drum

spring pin (see photo 2).

Step 2

Remove the drive hub-side blue plastic handle. Clean surround-

ing area with lint-free cloth.

Step 3Rotate the drum to position the drum spring pin in a horizontal

direction (see photo 3).

NOTE: Drum hub holes have different shapes: round on one

side (see photo 4), square on the opposite side (see photo 5).

Position the drum so that the round hole side is facing you and

always extract the spring pin from this side.

www.delacamp.com

8/20/2019 dprtool


© 2008 DELACAMP. All rights reserved. DELACAMP is a distributor of compatible replacement parts and products for imaging equipment. None of DELACAMP's products aregenuine OEM replacement parts and no affiliation or sponsorship is to be implied between DELACAMP and any OEM.

Drum Pin Removal Tool Article no. 61513

2


Patent Pending

Photo 6

Step 4

Remove the spring pin guard from the clip on the side of the

DRPINTOOL2 (see photo 6). Install the spring pin guard over

the exposed section of the drum spring pin (see photo 7) in

order to avoid damage to the drum spring pin during extraction.

NOTE: Keep the alignment pin cable away from contact withthe drum. The alignment pin cable may damage the drum sur-

face if contact occurs.

Photo 7

Photo 9

Photo 8

Step 5

Position the DRPINTOOL2: the alignment pin slides into the

opposite side of the spring pin guide to properly align the tool

with the drum spring pin (see photo 8).

NOTE: The tool pin has a small spike at the end (see photo 9).

Make sure the spike fits inside the drum spring pin when

extracting and installing the spring pin.

Photo 10

Step 6

Rotate the DRPINTOOL2 shaft until the pin lock nut meets the

spring pin guard (see photo 10).

Photo 11

Step 7

Unscrew the shaft to remove the spring pin guard. Realign the

DRPINTOOL2 using the alignment pin guide to properly alignthe tool with the drum spring pin to continue extraction (see

photo 11). Firmly hold the tool in place to prevent misalignment

Slowly rotate the shaft until the body of the tool is firmly fixed on

the drum and continue to rotate the shaft until the drum spring

pin falls free (see photo 12).

NOTE: Do not apply excessive force. If there is significant resist

ance, there is probably a misalignment of the pin and tool.

Misalignment can possibly damage both the tool and the spring

pin. Reverse removal a little, realign and try again.

www.delacamp.com

8/20/2019 dprtool




3


Patent Pending

Photo 12

Photo 13

Photo 14

DRIVE HUB PIN EXTRACTION

Step 1

Locate the smaller hole on the drive hub spring pin indicated by

the flat side of the drive hub with a small spike (see photo 13).

Step 2Use the alignment pin guide to properly align the tool with the

drive hub spring pin. Firmly hold the tool in place to prevent

misalignment. Slowly rotate the shaft until the body of the tool is

firmly fixed on the drive hub and continue to rotate the shaft

until the drive hub spring pin falls free.

NOTE: Do not apply excessive force. If there is significant resist-

ance, there is probably a misalignment of the pin and tool.



DRIVE HUB PIN INSTALLATION

Step 1

Place the drive hub spring pin into the larger hole of the drive

hub: pre-start it by hand (see photo 14).

Step 2Slide the drive hub onto the drive hub shaft aligning the spring

pin with the hole on the drive hub shaft (see photo 15).

Photo 15

Step 3

Use the alignment pin to align the tool with the drive hub and

drive hub shaft (see photo 16).

Photo 16

NOTES

www.delacamp.com

8/20/2019 dprtool




4


Patent Pending

Photo 17 Photo 20

Photo 21Photo 18

Photo 19

Step 4

Position the tool shaft on the hub spring pin and rotate the tool

shaft slowly. Hold the alignment pin with your finger until the

drive hub spring pin pushes on the alignment pin (see photo

17). Firmly hold the tool in place to prevent misalignment.

NOTE: Do not apply excessive force. If there is significant resist-ance, there is probably a misalignment. Reverse, realign and try

again.

DRUM PIN INSTALLATION

Step 1

Turn the drum so the square hole side of the drum hub is facing

you. Insert the drum spring pin into the square hole of the drum

hub (see photo 18). Use the alignment pin to align the tool with

the drum and drum shaft (see photo 19).

Step 2

Position the tool shaft on the spring pin and rotate the shaft

slowly. Hold the alignment pin with your finger until the drum

spring pin pushes on the alignment pin (see photo 20). Firmly

hold the tool in place to prevent misalignment.

NOTE: Do not apply excessive force. If there is significant resistance, there is probably a misalignment. Reverse, realign and try

again.

FOR USE WITH HP3000 SERIES CARTRIDGES

DRUM PIN EXTRACTION

Step 1

Release drum shutter to get unobstructed access to the drum

spring pin (see photo 21).

Step 2

Clean surrounding area with lint-free cloth.

Step 3Rotate the drum to position the drum spring pin in a horizontal

direction (see photo 22).

NOTE: Drum hub holes have different shapes: round on one

side (see photo 4), square on the opposite side (see photo 5).

Position the drum so that the round hole side is facing you and

always extract the spring pin from this side.

www.delacamp.com

8/20/2019 dprtool




www.delacamp.com


5


Patent Pending

Photo 22

Photo 24

Photo 25

Photo 26

Step 4

Position the DRPINTOOL2: use the alignment pin to align the

tool with the drum spring pin (see photo 23).

NOTE: Keep the alignment pin cable away from contact with

the drum. The alignment pin cable may damage the drum sur-

face if contact occurs.NOTE: The tool pin has a small spike at the end (see photo 9).

Make sure the spike fits inside the drum spring pin when

extracting and installing the spring pin.

Photo 23

Step 5

Rotate the DRPINTOOL2 shaft until the body of the tool is firmly

fixed on the drum. Make sure the tool and the drum spring pin

are properly aligned.

Step 6

Start extracting the drum spring pin from the drum, slowly rotat-

ing the shaft. Firmly hold the tool in place to prevent misalign-

ment. Continue to rotate the shaft until the spring pin falls free.

NOTE: Do not apply excessive force. If there is significant resist-ance, there is probably a misalignment of the pin and tool.



Step 2

Position the tool shaft on the spring pin and rotate the shaft

slowly. Hold the alignment pin with your finger until the drum

spring pin pushes on the alignment pin (see photo 26). Firmly

hold the tool in place to prevent misalignment.

NOTE: Do not apply excessive force. If there is significant resist

ance, there is probably a misalignment. Reverse, realign and try

again.

DRUM PIN INSTALLATIONStep 1

Turn the drum so the square hole side of the drum hub is facing

you. Insert the drum spring pin into the square hole of the drum

hub (see photo 24). Use the alignment pin to align the tool with

the drum and drum shaft (see photo 25).

8/20/2019 dprtool





www.delacamp.com 6


Patent Pending

Step 3

Insert replacement pin until it is firmly seated in the bottom of

the chuck.

Step 4

Begin to tighten the pin lock nut with your fingers. Use the

wrench to tighten the pin lock nut until snug.

NOTE: Do not over-tighten the pin lock nut with the wrench

or it may be damaged.

Photo 28

Photo 27

CHANGING PINS ON THE DRPINTOOL2

Step 1

Holding the DR Pin Tool by the black handle, loosen the pin lock

nut with the pin lock nut wrench (see photo 27).

Step 2Continue to loosen the pin lock nut with your fingers until the pin

can be pulled free (see photo 28).

NOTES

dprtool

Documents