Download - Yamaha RX-V677 manual
-
8/21/2019 Yamaha RX-V677 manual
1/146
English
AV Receiver
Owner’s Manual
Read the supplied booklet “Safety Brochure” before using the unit.
-
8/21/2019 Yamaha RX-V677 manual
2/146
-
8/21/2019 Yamaha RX-V677 manual
3/146
-
8/21/2019 Yamaha RX-V677 manual
4/146
-
8/21/2019 Yamaha RX-V677 manual
5/146
Accessories En 5
AccessoriesCheck that the following accessories are supplied with the product.
Remote control Batteries (AAA, R03, UM-4) (x2)
AM antenna FM antenna
*One of the above is supplied depending on the region ofpurchase.
YPAO microphone Wireless antenna
CD-ROM (Owner’s Manual)
Easy Setup Guide
Safety Brochure
Insert the batteries the right
way round.
Operating range of the remote control
• Point the remote control at the remote control sensor on the unit and remain within the operating rangeshown below.
• The illustrations of the main unit and remote control used in this manual are of the RX-V777 (U.S.A.model), unless otherwise specified.
• (RX-V777 [China, Korea, U.K. and Europe models] only)For information on how to control external devices with the remote control, refer to “Supplement forRemote Control” on the supplied CD-ROM.
• Some features are not available in certain regions.
• Due to product improvements, specifications and appearance are subject to change without notice.
• This manual explains operations using the supplied remote control.
• This manual describes all the “iPod”, “iPhone” and “iPad” as the “iPod”. “iPod” refers to “iPod”, “iPhone”and “iPad”, unless otherwise specified.
• indicates precautions for use of the unit and its feature limitations.
• indicates supplementary explanations for better use.
30° 30°
Within6 m (20 ft)
(RX-V777) (RX-V677)
30° 30°
-
8/21/2019 Yamaha RX-V677 manual
6/146
FEATURES ➤ What you can do with the unit En 6
FEATURES
What you can do with the unit
AV receiver (the unit)
Speakers
BD/DVD player
HDMI Control
Audio/Video
TV remote control
Audio
HDMI Control
Audio
Audio/Video
TV
Sequential operation of a TV,AV receiver, and BD/DVD
player (HDMI Control)
p.134
Change the input sourceand favorite settings with
one touch (SCENE)
p.51
Supports 2- to 7.1-channel (plus presence)speaker system. Allows you to enjoy your favoriteacoustic spaces in various styles.
Automatically optimizing the speakersettings to suit your room (YPAO)
p.34
• Reproducing stereo or multichannelsounds with the sound fields likeactual movie theaters and concert halls(CINEMA DSP)
p.53
• Enjoying compressed music withenhanced sound (Compressed MusicEnhancer)
p.57
• Playing back music in multiple rooms(multi-zone)
p.78
iPod/iPhone/iPad
USB deviceAudio
Network contents
Wide variety of supported content
• iPod/iPhone/iPad p.63
• USB p.66
• Media server (PC/NAS)
p.69
• Internet radio
p.73• AirPlay
p.76
3D and 4K Ultra HDsignals supported
Audio/Video(via HDMI/MHL)
Smartphone/Tablet
Control
Control
-
8/21/2019 Yamaha RX-V677 manual
7/146
-
8/21/2019 Yamaha RX-V677 manual
8/146
FEATURES ➤ Part names and functions En 8
Front panel (RX-V777)
1MAIN ZONEz keyTurns on/off (standby) the unit.
2 Standby indicatorLights up when the unit is in standby mode under any of thefollowing conditions.
• HDMI Contorol is enabled (p.106)
• Standby Through is enabled (p.107)
• Network Standby is enabled (p.108)
• An iPod is being charged (p.63)
3 ZONE 2 keyEnables/disables the audio output to Zone2 (p.81).
4 ZONE CONTROL keyChanges the zone (main zone or the Zone2) that is controlledby the keys and knobs on the front panel (p.81).
5 INFO (WPS) keySelects the information displayed on the front display (p.86).
Enters the wireless network connection setup (WPS pushbutton configuration) by holding down for 3 seconds (p.44).
6MEMORY keyRegisters FM/AM radio stations as preset stations (p.59).
7 PRESET keysSelect a preset FM/AM radio station (p.59).
8 FM and AM keysSwitch between FM and AM (p.58).
9 Front displayDisplays information (p.10).
0 Remote control sensorReceives remote control signals (p.5).
A TUNING keys
Select the radio frequency (p.58).B PURE DIRECT key
Enables/disables Pure Direct (p.57).
C INPUT knobSelects an input source.
D PHONES jack For connecting headphones.
E YPAO MIC jack For connecting the supplied YPAO microphone (p.34).
F TONE CONTROL keyAdjusts the high-frequency range and low-frequency rangeof output sounds (p.88).
G SCENE keysSelect the registered input source, sound program, andvarious settings with one touch. Also, turns on the unit whenit is in standby mode (p.51).
H PROGRAM keysSelect a sound program or a surround decoder (p.52).
I STRAIGHT keyEnables/disables the straight decode mode (p.56).
J VIDEO AUX (HDMI/MHL IN) jack For connecting a device, such as a camcorder and a gameconsole (p.28) or a smartphone (p.29).
K USB jack For connecting a USB storage device (p.66) or an iPod(p.63).
VIDEO jack For inputting video when “USB” is selected as the inputsource.
L VOLUME knobAdjusts the volume.
Part names and functions
INFO(WPS)ZONE2 ZONECONTROL MEMORY PRESET FM AM TUNING
CONTROL
TVBD
DVD NET RADIO
INPUT
SCENE
MAIN ZONE
PHONES
SILENT CINEMA
STRAIGHT
VIDEO
PUREDIRECT
HDMI/ 5 V 2 .1 A
VIDEO
VOLUME
AUXTONE PROGRAM YPAO MIC
M HL 5 V 1 A
:9 B2 3 4 5 61 7 8 A
C LFED H I J KG
-
8/21/2019 Yamaha RX-V677 manual
9/146
FEATURES ➤ Part names and functions En 9
Front panel (RX-V677)
1MAIN ZONEz keyTurns on/off (standby) the unit.
2 Standby indicatorLights up when the unit is in standby mode under any of thefollowing conditions.
• HDMI Contorol is enabled (p.106)
• Standby Through is enabled (p.107)
• Network Standby is enabled (p.108)
• An iPod is being charged (p.63)
3 YPAO MIC jack For connecting the supplied YPAO microphone (p.34).
4 ZONE 2 keyEnables/disables the audio output to Zone2 (p.81).
5 Remote control sensorReceives remote control signals (p.5).
6 ZONE CONTROL keyChanges the zone (main zone or the Zone2) that is controlledby the keys and knobs on the front panel (p.81).
7 INFO (WPS) keySelects the information displayed on the front display (p.86).
Enters the wireless network connection setup (WPS pushbutton configuration) by holding down for 3 seconds (p.44).
8MEMORY keyRegisters FM/AM radio stations as preset stations (p.59).
9 PRESET keysSelect a preset FM/AM radio station (p.59).
0 FM and AM keysSwitch between FM and AM (p.58).
A Front displayDisplays information (p.10).
B TUNING keysSelect the radio frequency (p.58).
C PURE DIRECT keyEnables/disables Pure Direct (p.57).
D PHONES jack For connecting headphones.
E INPUT keysSelect an input source.
F TONE CONTROL keyAdjusts the high-frequency range and low-frequency rangeof output sounds (p.88).
G SCENE keysSelect the registered input source, sound program, andvarious settings with one touch. Also, turns on the unit when
it is in standby mode (p.51).
H PROGRAM keysSelect a sound program or a surround decoder (p.52).
I STRAIGHT keyEnables/disables the straight decode mode (p.56).
J VIDEO AUX (HDMI/MHL IN) jack For connecting a device, such as a camcorder and a gameconsole (p.28) or a smartphone (p.29).
K USB jack For connecting a USB storage device (p.66) or an iPod(p.63).
VIDEO jack For inputting video when “USB” is selected as the inputsource.
L VOLUME knobAdjusts the volume.
INFO(WPS)ZONE2 ZONECONTROL MEMORY PRESET FM AM TUNING
CONTROL
TVBD
DVD NET RADIO
SCENE
MAIN ZONE
PHONES
SILENT CINEMA
STRAIGHT
VIDEO
PURE DIRECT
VIDEO
VOLUME
AUXTONE PROGRAM
YPAO MIC
INPUT
HDMI/ 5V 2.1AMHL 5V 1A
5 A C3 4 6 7 81 2 9 :
D LF H I J KE G
B
-
8/21/2019 Yamaha RX-V677 manual
10/146
FEATURES ➤ Part names and functions En 10
Front display (indicators)
1 ECOLights up when the unit is in the eco mode (p.113).
2 HDMILights up when HDMI signals are being input or output.
OUT1/OUT2 (RX-V777 only)Indicates the HDMI OUT jacks currently outputting an HDMIsignal
OUT (RX-V677 only)Lights up when HDMI signals are being output.
3 ENHANCERLights up when Compressed Music Enhancer (p.57) is
working.
4 CINEMA DSPLights up when CINEMA DSP or CINEMA DSP 3D (p.53) isworking.
5 STEREOLights up when the unit is receiving a stereo FM radio signal.
TUNEDLights up when the unit is receiving an FM/AM radio stationsignal.
6 Signal strength indicatorIndicates the strength of the wireless network signal (p.42).
7 PARTY (RX-V777 only)Lights up when the unit is in the party mode. (p.82)
8 SLEEPLights up when the sleep timer is on.
9 ZONE2Lights up when audio output to Zone2 is enabled (p.81).
0MUTEBlinks when audio is muted.
A Volume indicatorIndicates the current volume.
B VIRTUALLights up when the Virtual Presence Speaker (VPS) (p.53) orthe virtual surround processing (p.55) is working.
C Cursor indicatorsIndicate the remote control cursor keys currently operational.
D Information displayDisplays the current status (such as input name and soundmode name). You can switch the information by pressingINFO (p.86).
E ADAPTIVE DRCLights up when Adaptive DRC (p.88) is working.
F Speaker indicatorsIndicate speaker terminals from which signals are output.
A Front speaker (L)
S Front speaker (R)D Center speaker
F Surround speaker (L)G Surround speaker (R)H Surround back speaker (L)
J Surround back speaker (R)K Surround back speakerB Presence speaker (L)
N Presence speaker (R)
L Subwoofer
L C R FPRFPL
SL
SBL SBRSB
SW SR
VOL.
MUTE
ADAPTIVE DRC VIRTUAL
ENHANCER TUNEDSTEREO
2
SLEEPPARTY
ZONEOUT 1 2
2 B3 4 7 8 :1 96 A5
C CD E F
-
8/21/2019 Yamaha RX-V677 manual
11/146
FEATURES ➤ Part names and functions En 11
Rear panel (RX-V777)
1 REMOTE IN/OUT jacksFor connecting to an infrared signal receiver/emitter thatallows you to operate the unit and other devices from anotherroom (p.80).
2 TRIGGER OUT jack For connecting to a device that supports the trigger function(p.32).
3 DC OUT jack For connecting to an optional accessory.
4 HDMI OUT 1–2 jacks
For connecting to HDMI-compatible TVs and outputtingvideo/audio signals (p.23). When using ARC, TV audio signalcan also be input through the HDMI OUT 1 jack.
5 ANTENNA jacksFor connecting to FM and AM antennas (p.29).
6MONITOR OUT jacks
COMPONENT VIDEO jacksFor connecting to a TV that supports component video andoutputting video signals (p.23).
VIDEO jack For connecting to a TV that supports composite video andoutputting video signals (p.24).
7 HDMI 1–5 jacksFor connecting to HDMI-compatible playback devices andinputting video/audio signals (p.25).
8 SPEAKERS terminalsFor connecting to speakers (p.19).
9 NETWORK jack For connecting to a network with a network cable (p.30).
0WIRELESS jack For connecting the supplied wireless antenna (p.30).
A VOLTAGE SELECTOR(General model only)Selects the switch position according to your local voltage(p.32).
B Power cableFor connecting to an AC wall outlet (p.32).
C PHONO jacks(Except for U.S.A. and Canada models)
For connecting to a turntable (p.28).
D AUDIO 1–2 jacksFor connecting to audio playback devices and inputtingaudio signals (p.28).
E AV 1–6 jacksFor connecting to video/audio playback devices andinputting video/audio signals (p.25).
F AV OUT jacksFor outputting video/audio to a recording device (such as aVCR) (p.31).
G ZONE2 OUT jacksFor connecting to the external amplifier used in Zone2 andfor outputting audio (p.79).
H PRE OUT jacks
For connecting to a subwoofer with built-in amplifier or to anexternal power amplifier (p.31).
AUDIO 1 AUDIO 2
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV 1
(TV)
PBY PR
COMPONENTVIDEO
VIDEO
MONITOR OUT
PB
Y
PR
HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)
12
ARC
ANTENNA
FMAM
FRONT CENTER SURROUND
SINGLE
SURROUNDBACK/BI-AMP
SPEAKERS
AV 5
VIDEO
AV 6 AV OUT ZONE OUT SUBWOOFERSUR.BACKSURROUNDFRONT
PRE OUT
CENTER
SINGLE
ZONE 2
NETWORKDC OUT
TRIGGER OUT
REMOTE
5V 0.5A (NET)
12V
IN
OUT
0.1A
ZONE2/F.PRESENCE
EXTRA SP
COMPONENT VIDEO
CENTER
1
2
HDMI OUT
(RADIO)
WIRELESS
2
GD H
8
F
71 3 4 9
C
A B0
E
65
* The area around the video/audio output jacks ismarked in white on the actual product toprevent improper connections.
(U.S.A. model)
-
8/21/2019 Yamaha RX-V677 manual
12/146
FEATURES ➤ Part names and functions En 12
Rear panel (RX-V677)
1 REMOTE IN/OUT jacksFor connecting to an infrared signal receiver/emitter that
allows you to operate the unit and other devices from anotherroom (p.80).
2 TRIGGER OUT jack For connecting to a device that supports the trigger function(p.32).
3 DC OUT jack For connecting to an optional accessory.
4 HDMI OUT jack
For connecting to an HDMI-compatible TV and outputtingvideo/audio signals (p.23). When using ARC, TV audio signalcan also be input through the HDMI OUT jack.
5 ANTENNA jacksFor connecting to FM and AM antennas (p.29).
6MONITOR OUT jacks
COMPONENT VIDEO jacksFor connecting to a TV that supports component video andoutputting video signals (p.23).
VIDEO jack For connecting to a TV that supports composite video andoutputting video signals (p.24).
7 HDMI 1–5 jacksFor connecting to HDMI-compatible playback devices and
inputting video/audio signals (p.25).
8 SPEAKERS terminalsFor connecting to speakers (p.19).
9 NETWORK jack For connecting to a network with a network cable (p.30).
0WIRELESS jack For connecting the supplied wireless antenna (p.30).
A VOLTAGE SELECTOR(General model only)
Selects the switch position according to your local voltage(p.32).
B Power cableFor connecting to an AC wall outlet (p.32).
C AUDIO 1–2 jacksFor connecting to audio playback devices and inputtingaudio signals (p.28).
D AV 1–6 jacksFor connecting to video/audio playback devices andinputting video/audio signals (p.25).
E AV OUT jacksFor outputting video/audio to a recording device (such as a
VCR) (p.31).
F ZONE2 OUT jacksFor connecting to the external amplifier used in Zone2 andfor outputting audio (p.79).
G SUBWOOFER PRE OUT 1–2 jacksFor connecting to a subwoofer with built-in amplifier (p.31).
AUDIO 1 AUDIO 2
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV 1
(TV)
PBY PR
COMPONENTVIDEO
VIDEO
MONITOR OUT
PB
Y
PR
HDMI OUT
ARC
ANTENNA(RADIO)
FMAM
FRONT CENTER SURROUND
SINGLE
SURROUNDBACK/BI-AMP
SPEAKERS
AV 5 AV 6 AV OUT ZONE OUTSUBWOOFERPRE OUT
ZONE 2
NETWORKDC OUT
TRIGGER OUT
REMOTE
5V 0.5A (NET)
12V
IN
OUT
0.1A
ZONE2/F.PRESENCE
EXTRA SP
COMPONENT VIDEO
HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)
VIDEO
1
2
WIRELESS
2
F GC
8
E
71 3 4 9 A B
D
5 6 0
* The area around the video/audio output jacks ismarked in white on the actual product to preventimproper connections.
(U.S.A. model)
-
8/21/2019 Yamaha RX-V677 manual
13/146
-
8/21/2019 Yamaha RX-V677 manual
14/146
PREPARATIONS ➤ General setup procedure En 14
PREPARATIONS
This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit!
General setup procedure
1 Placing speakers (p.15) Select the speaker layout for the number of speakers that you are using and place them in your room.
2 Connecting speakers (p.19) Connect the speakers to the unit.
3 Connecting a TV (p.23) Connect a TV to the unit.
4 Connecting playback devices (p.25) Connect video devices (such as BD/DVD players) and audio devices (such as CD players) to the unit.
5 Connecting the FM/AM antennas (p.29) Connect the supplied FM/AM antennas to the unit.
6Connecting a network cable or thewireless antenna (p.30)
Connect the unit to a router (access point) with a network cable, or connect the supplied wireless antenna
for establishing a wireless network connection.
7 Connecting other devices (p.31) Connect external devices, such as an external power amplifier (RX-V777 only) and recording devices.
8 Connecting the power cable (p.32) After all the connections are complete, plug in the power cable.
9Selecting an on-screen menu language
(p.33)Select the desired on-screen menu language (default: English).
10Optimizing the speaker settingsautomatically (YPAO) (p.34)
Optimize the speaker settings, such as volume balance and acoustic parameters, to suit your room
(YPAO).
11Connecting to a network device wirelessly(p.42)
Connect the unit to a wireless router (access point) or a mobile device by establishing a wireless
connection.
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
15/146
PREPARATIONS ➤ Placing speakers En 15
Select the speaker layout for the number of speakers that you are using and place the speakers and subwoofer (with built-in amplifier) in your room. This section describes the
representative speaker layout examples.
If you use five speakers in the front side, use two of them as front surround speakers (*1) or presence speakers (*2). We recommend using them as front surround speakers forenjoying unprocessed playback (p.56) or presence speakers for enjoying stereoscopic sound fields (p.53).
• For information on the ideal speaker layout, see “Ideal speaker layout” (p.128).
• If you have seven speakers, use two of them as surround back speakers or presence speakers.To reinforce the rear left/right sounds, use them as surround back speakers.To create a natural 3-dimensional sound field, use them as presence speakers.
• Two subwoofers connected to the unit output the same sounds.
1 Placing speakers
Caution
• Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 MIN”. In this case, you can also use 4-ohm speakers as the front speakers.For details, see “Setting the speaker impedance” (p.18).
Speaker type Abbr. Function
Speaker system (the number of channels)
7.1+2 7.1 7.1 6.1 5.1Front
5.14.1 3.1 2.1
Front (L) 1Produce front left/right channel sounds (stereo sounds).
● ● ● ● ● ● ● ● ●
Front (R) 2 ● ● ● ● ● ● ● ● ●
Center 3 Produces center channel sounds (such as movie dialogue and vocals). ● ● ● ● ● ● ●
Surround (L) 4Produce surround left/right channel sounds. Surround speakers also produce surround back channelsounds when no surround back speakers are connected.
● ● ● ● ● *1 ●
Surround (R) 5 ● ● ● ● ● *1 ●
Surround back (L) 6Produce surround back left/right channel sounds.
● ●
Surround back (R) 7 ● ●
Surround back 8 Produces sounds mixed from surround back left/right channel sounds. ●
Presence (L) EProduce CINEMA DSP effect sounds. In combination with CINEMA DSP 3D (p.53), the presence speakerscreate a natural 3-dimensional sound field in your room.
● ● *2
Presence (R) R ● ● *2
Subwoofer 9Produces LFE (low-frequency effect) channel sounds and reinforces the bass parts of other channels.
This channel is counted as “0.1”. You can connect 2 subwoofers (with built-in amplifier) to the unit. ● ● ● ● ● ● ● ● ●
1 2 3 4 5 6 7 8 9 10 11
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
16/146
PREPARATIONS ➤ Placing speakers En 16
7.1+2-channel system
• The surround back speakers and presence speakers do not produce sounds simultaneously. The unitautomatically changes the speakers to be used, depending on the selected CINEMA DSP (p.53).
7.1-channel system (using presence speakers)
This speaker system uses the front presence speakers to produce a natural
3-dimensional sound field, and is suited for enjoying 5.1-channel contents.
7.1-channel system (using surround back speakers)
This speaker system creates Virtual Presence Speaker (VPS) using the front, center and
surround speakers to produce a 3-dimensional sound field, and also allows you to
enjoy extended surround sounds using the surround back speakers.
6.1-channel system
This speaker system creates Virtual Presence Speaker (VPS) using the front, center and
surround speakers to produce a 3-dimensional sound field, and also allows you to
enjoy extended surround sounds using the surround back speaker.
4 5
1 2
39
6 7
E R
9
4 5
1 2
39
E R
4 5
1 2
39
6 7
4 5
1 2
39
8
1 2 3 4 5 6 7 8 9 10 11
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
17/146
PREPARATIONS ➤ Placing speakers En 17
5.1-channel system
This speaker system creates Virtual Presence Speaker (VPS) using the front, center and
surround speakers to produce a 3-dimensional sound field, and is suited for enjoying
5.1-channel contents.
Front 5.1-channel system (using surround speakers)
Even when surround speakers are placed in the front side, the unit creates the virtual
surround speakers in the rear side to allow you to enjoy multi-channel surround sound (Virtual
CINEMA FRONT) when “Layout (Surround)” (p.101) in the “Setup” menu is set to “Front”.
• You can enjoy surround sound even without the center speaker (front 4.1-channel system).
Front 5.1-channel system (using presence speakers)
This speaker system uses the front presence speakers to produce a natural
3-dimensional sound field, and creates the virtual surround speakers using the front
speakers to allow you to enjoy multi-channel surround sound (Virtual CINEMA DSP).
4.1-channel system
4 5
1 2
39
4 5
1 2
39
1 2
39
E R
4 5
1 2
9
1 2 3 4 5 6 7 8 9 10 11
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
18/146
PREPARATIONS ➤ Placing speakers En 18
2.1-channel system
Even when no surround speakers are connected, the unit creates the virtual surround
speakers using the front speakers to allow you to enjoy multi-channel surround sound
(Virtual CINEMA DSP).
• Add the center speaker to configure a 3.1-channel system.
■ Setting the speaker impedanceUnder its default settings, the unit is configured for 8-ohm speakers. When using a
6-ohm speaker for any channel, set the speaker impedance to “6 MIN”. In this case,
you can also use 4-ohm speakers as the front speakers.
1 Before connecting speakers, connect the power cable to an AC walloutlet.
2 While holding down STRAIGHT on the front panel, pressMAIN ZONEz.
3 Check that “SP IMP.” is displayed on the front display.
4 Press STRAIGHT to select “6 MIN”.
5 Press MAIN ZONEz to set the unit to standby mode and remove thepower cable from the AC wall outlet.
You are now ready to connect the speakers.
1 2
9
MAIN ZONEz
STRAIGHT
SP IMP. 8 MIN
1 2 3 4 5 6 7 8 9 10 11
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
19/146
PREPARATIONS ➤ Connecting speakers En 19
Connect the speakers placed in your room to the unit.
The following diagrams provide connections for 7.1+2-,
7.1-, and 6.1-channel systems as examples. For othersystems, connect speakers while referring to the
connection diagram for the 6.1-channel system.
Cables required for connection
(commercially available)
Speaker cables (x the number of speakers)
Audio pin cable (two for connecting two subwoofers)
7.1+2-channel system 7.1-channel system
(using surround back speakers)
2 Connecting speakers
Caution
• Remove the unit’s power cable from an AC wall outlet and turnoff the subwoofer before connecting the speakers.
• Ensure that the core wires of the speaker cable do not touchone another or come into contact with the unit’s metal parts.Doing so may damage the unit or the speakers. If the speaker
cables short circuit, “Check SP Wires” will appear on the frontdisplay when the unit is turned on.
• The illustrations of the unit (rear) used in this section are of theRX-V777.
–
+
–
+
FRONT CENTER SURROUND
SINGLE
SURROUND BACK/BI-AMP
SPEAKERS
ZONE2/F.PRESENCE
EXTRA SP
1
2
1
6 7
2
3
4 5
9 9
E R
The unit (rear)
FRONT CENTER SURROUND
SINGLE
SURROUND BACK/BI-AMP
SPEAKERS
ZONE2/F.PRESENCE
EXTRA SP
1
2
1
6 7
2
3
4 5
9
The unit (rear)
1 2 3 4 5 6 7 8 9 10 11
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
20/146
PREPARATIONS ➤ Connecting speakers En 20
7.1-channel system(using presence speakers)
6.1-channel system ■ Connecting speaker cablesSpeaker cables have two wires. One is for connecting
the negative (-) terminal of the unit and the speaker, and
the other is for the positive (+) terminal. If the wires are
colored to prevent confusion, connect the black wire tothe negative and the other wire to the positive terminal.
a Remove approximately 10 mm (3/8”) of insulation from
the ends of the speaker cable and twist the bare wires of
the cable firmly together.
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the side
(upper right or bottom left) of the terminal.
d Tighten the terminal.
Using a banana plug
(U.S.A., Canada, China, Australia and General models only)
a Tighten the speaker terminal.
b Insert a banana plug into the end of the terminal.
FRONT CENTER SURROUND
SINGLE
SURROUND BACK/BI-AMP
SPEAKERS
ZONE2/F.PRESENCE
EXTRA SP
1
2
1 2
3
4 5
9
E R
The unit (rear)
FRONT CENTER SURROUND
SINGLE
SURROUND BACK/BI-AMP
SPEAKERS
ZONE2/F.PRESENCE
EXTRA SP
1
2
1 2
3
4 5
9
8
When using only one surround back speaker, connect it
to the SINGLE jack (L side).
The unit (rear)
FRONT
aa
b
d
c+ (red)
- (black)
FRONTa
b
Banana plug
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
21/146
PREPARATIONS ➤ Connecting speakers En 21
Push-type speaker terminals
(RX-V677 only)
a Remove approximately 10 mm (3/8”) of insulation from
the ends of the speaker cable, and twist the bare wires of
the cable firmly together.
b Press down the tab.
c Insert the bare wires of the cable into the hole in the
terminal.
d Release the tab.
■ Connecting the subwooferUse an audio pin cable to connect the subwoofer.
Connecting front speakers thatsupport bi-amp connections
When using front speakers that support bi-amp
connections, connect them to the FRONT jacks and
SURROUND BACK/BI-AMP jacks.
To enable the bi-amp function, set “Power Amp Assign”
(p.100) in the “Setup” menu to “5ch BI-AMP” after
connecting the power cable to an AC wall outlet.
• The FRONT jacks and SURROUND BACK/BI-AMP jacks output thesame signals.
ONE 2 / F.PRESENCE
TRA SP
aa b
c
d + (red)
- (black)
Audio pin cable
1 2
3
4 5
9
FRONT CENTER SURROUND
SINGLE
SURROUND BACK/BI-AMP
SPEAKERS
ZONE2/F.PRESENCE
EXTRA SP
1
2
The unit (rear)
Caution
• Before making bi-amp connections, remove any brackets orcables that connect a woofer with a tweeter. Refer to theinstruction manual of the speakers for details. If you are notmaking bi-amp connections, make sure that the brackets or
cables are connected before connecting the speaker cables.• Surround back speakers cannot be used during bi-amp
connections.
-
8/21/2019 Yamaha RX-V677 manual
22/146
PREPARATIONS ➤ Input/output jacks and cables En 22
■ Video/audio jacks
❑ HDMI jacks
Transmit digital video and digital sound through a single
jack. Use an HDMI cable.
• Use a 19-pin HDMI cable with the HDMI logo. We recommend usinga cable less than 5.0 m (16.4 ft) long to prevent signal qualitydegradation.
• The unit’s HDMI jacks support the HDMI Control, Audio ReturnChannel (ARC), and 3D and 4K Ultra HD video transmissionfeatures.
• Use high speed HDMI cables to enjoy 3D or 4K Ultra HD videos.
❑ HDMI/MHL jack
Transmits digital video and digital sound. Use an MHL
or HDMI cable.
• The VIDEO AUX jack on the front panel of the unit supports bothMHL and HDMI connections. Use a cable that matches the jack onyour MHL-compatible mobile device. For details on an MHLconnection, see “MHL connection” (p.29). When connecting anHDMI-compatible playback device to the VIDEO AUX jack, use anHDMI cable.
■ Video jacks
❑ COMPONENT VIDEO jacks
Transmit video signals separated into three
components: luminance (Y), chrominance blue (PB),
and chrominance red (PR). Use a component video
cable with three plugs.
❑ VIDEO jacks
Transmit analog video signals. Use a video pin cable.
■ Audio jacks
❑ OPTICAL jacks
Transmit digital audio signals. Use a digital optical
cable. Remove the tip protector (if available) before
using the cable.
❑ COAXIAL jacks
Transmit digital audio signals. Use a digital coaxial
cable.
❑ AUDIO jacks
Transmit analog stereo audio signals. Use a stereo pin
cable (RCA cable).
Input/output jacks and cables
HDMI cable
MHL or HDMI cable
OR OUT
Component video cable
Video pin cable
OPTICAL
Digital optical cable
COAXIAL
Digital coaxial cable
Stereo pin cable
-
8/21/2019 Yamaha RX-V677 manual
23/146
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
24/146
PREPARATIONS ➤ Connecting a TV En 24
❑ VIDEO (composite video) connection (with a video pin cable)
■ Connecting another TV or a projector(RX-V777 only)
The unit has two HDMI output jacks. If you connect another TV or a projector to the unit
with an HDMI cable, you can switch the TV (or projector) to be used for watching
videos with the remote control (p.50).
• HDMI Control is not available on the HDMI OUT 2 jack.
A UD IO 1 A UD IO 2
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV1
(TV)
PBY PR
COMPONENTVIDEO
VIDEO
MONITOR OUT
PB
Y
PR
HDMI 1 HDMI 2 HDMI 3(BD/DVD)
12
ARC
ANTENNA
FMAM
AV5
VIDEO
AV6 AVOUT ZONE OUTSUFRONTZONE 2
DC OUT
TRIGGER OUT
REMOTE
5V 0.5A
12V
IN
OUT
0.1A
COMPONENT VIDEO
HDMI OUT
(RADIO)
VIDEOVIDEO
MONITOR
V V
OPTICAL
O
O
OPTICAL
AV4
(TV)
The unit (rear)MONITOR OUT
(VIDEO) jackVideo input
(composite video)
AV 4 (OPTICAL) jack Audio output(digital optical)
TV
AUDIO1 AUDIO2
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV1
(TV)
PBY PR
VIDE
MO
HDMI 1 HDMI 2(BD/DVD)
12
ARC
ANTENNA
FMAM
AV5
VIDEO
AV6 AVOUT ZONEZONE
DC OUT
TRIGGER OUT
REMOTE
5V 0.5A
12V
IN
OUT
0.1A
COMPONENT VIDEO
HDMI OUT
(RADIO)
HDMI
HDMI
2 1
OUT
ARC
HDMI
H D MI
The unit (rear)
HDMI OUT 2 jack
HDMI input
Projector
TV (already connected)
TV
-
8/21/2019 Yamaha RX-V677 manual
25/146
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
26/146
PREPARATIONS ➤ Connecting playback devices En 26
■ Composite video connectionConnect a video device to the unit with a video pin cable and an audio cable (digital
coaxial, digital optical, or stereo pin cable). Choose a set of input jacks (on the unit)
depending on the audio output jacks available on your video device.
If you select the input source by pressing AV 3–6, the video/audio played back on the
video device will be output from the unit.
• To watch videos input to the AV 3–6 (VIDEO) jacks, you need to connect your TV to the HDMI OUT jack(p.23) or to the MONITOR OUT (VIDEO) jack (p.24) of the unit. For details, refer to “Video signal flow”(p.133).
■ Changing the combination of video/audio input jacksIf the combination of video/audio input jacks available on the unit does not match your
video device, change its combination according to the output jacks of your device. You
can connect a video device that has the following video/audio output jacks.
❑ Necessary setting
For example, if you have connected a video device to AV 2 (COMPONENT VIDEO) and
AV 5 (AUDIO) jacks of the unit, change the combination setting as follows.
Output jacks on video deviceInput jacks on the unit
Video Audio
Composite video
Digital coaxial AV 3 (VIDEO + COAXIAL)
Digital optical AV 4 (VIDEO + OPTICAL)
Analog stereo AV 5–6 (VIDEO + AUDIO)
AUDIO1 AUDIO2
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV1
(TV)
PBY PR
HDMI 1(BD/DVD)
12
ARC
AN
AM
AV5
VIDEO
AV6 A
DC OUT
TRIGGER OUT
REMOTE
5V 0.5A
12V
IN
OUT
0.1A
COMPONENT VIDEO
HDMI OUT
(R
R
L
COAXIAL
OPTICAL
OPTICAL
COAXIAL
VIDEO
VIDEO
C C
L
R
L
R
O O
V
V
The unit (rear)
AV 3–6 (VIDEO) jack
Video output
(composite video)
Video device
Audio output(either digital optical,
digital coaxial, or analog stereo)
Any of AV 3 (COAXIAL) jack,AV 4 (OPTICAL) jack,AV 5–6 (AUDIO) jacks
Output jacks on video device Input jacks on the unit
Video Audio Video Audio
HDMI
Digital optical HDMI 1–5AV 1 (OPTICAL)
AV 4 (OPTICAL)
Digital coaxial HDMI 1–5 AV 2–3 (COAXIAL)
Analog stereo HDMI 1–5AV 5–6 (AUDIO)
AUDIO 1–2
Component video Analog stereoAV 1–2
(COMPONENTVIDEO)
AV 5–6 (AUDIO)
AUDIO 1–2
A UD IO 1 A UD IO 2
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV1
(TV)
PBY PR
HDMI 1(BD/DVD)
12
ARC
ANTEN
AM
AV5
VIDEO
AV6 AVO
DC OUT
TRIGGER OUT
REMOTE
5V 0.5A
12V
IN
OUT
0.1A
COMPONENT VIDEO
HDMI OUT
(RADIO
AV 5
R
LAUDIO
AV2
PBY PR
L
R
L
R
PR
PB
Y
COMPONENTVIDEO
PR
PB
Y
PR
PB
Y
AV 2 (COMPONENT VIDEO) jacks
Video output(component video)
AV 5 (AUDIO) jacks
Video device
Audio output(analog stereo)
The unit (rear)
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
27/146
PREPARATIONS ➤ Connecting playback devices En 27
• The following operation is available only when your TV is connected to the unit via HDMI.
1 After connecting external devices (such as a TV and playbackdevices) and power cable of the unit, turn on the unit.
2 Press AV 2 to select “AV 2” (video input jack to be used) as the inputsource.
3 Press ON SCREEN.
4 Use the cursor keys to select “Input” and press ENTER.5 Use the cursor keys (e / r) to select “AV2” (video input jack to be
used) and press the cursor key (q).
6 Use the cursor keys to select “Audio In” and press ENTER.
7 Use the cursor keys to select “AV5” (audio input jack to be used).
8 Press ON SCREEN.This completes the necessary settings.
If you select “AV 2” as the input source by pressing AV 2, the video/audio played back
on the video device will be output from the unit.DISPLAYRETURN
ENTER
ON
SCREEN OPTION
POP-UP/MENU
ISPLAYRETURN
- /
TUNER USB
AV
AUDIO
5
65
V-AUX
1 2
1 2
3 4
SB
AUDIO
5
-
1
1 2
3 4
ON SCREEN
ENTER
AV 2
Cursor keys
-
8/21/2019 Yamaha RX-V677 manual
28/146
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
29/146
PREPARATIONS ➤ Connecting the FM/AM antennas En 29
❑ MHL connection
Connect an MHL-compatible mobile device (such as smartphones) to the unit with an
MHL cable. You can enjoy full HD videos and multichannel audio sources stored on the
mobile device. The VIDEO AUX jack of the unit enables you to input videos and audio
directly from the mobile device to the unit.
If you select “V-AUX” as the input source by pressing V-AUX, the video/audio playedback on the mobile device will be output from the unit.
• To watch videos input to the VIDEO AUX jack, you need to connect your TV to the HDMI OUT jack of theunit (p.23).
• You need to prepare an MHL cable that match the jack on your mobile device.
• You can operate the mobile device using the menu operation keys, external device operation keys andnumeric keys on the remote control. However, some features may not be compatible, depending on themobile device or its application. In this case, operate the mobile device itself.
• If “Standby Through” (p.107) in the “Setup” menu is set to “On”, you can output mobile device videos/audioto the TV or operate the mobile device using the remote control of the unit even when the unit is in standbymode.
• The unit supplies power to the mobile device in the following conditions.
– The unit is turned on.
– The unit is in standby mode while “Standby Through” (p.107) in the “Setup” menu is set to “On”.
Connect the supplied FM/AM antennas to the unit.
Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface.
Assembling and connecting the AM antenna
• Unwind only the length of cable needed from the AM antenna unit.
• The wires of the AM antenna have no polarity.
CONTROL
TVBD
DVD NET RADIO
PHONES
SILENT CINEMA
STRAIGHT
VIDEOHDMI/ 5 V 2 .1 A
VIDEO AUXTONE PROGRAM YPAO MIC
M HL 5 V 1 A
MHL
MHL
Mobile device
MHL output
The unit (front)
5 Connecting the FM/AM antennas
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV1
(TV)
PBY PR
COMPONENTVIDEO
VIDEO
MONITOR OUT
PB
Y
PR
HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)
12
ARC
ANTENNA
FMAM
FRONT CENTER SURROUND
SPEAKERS
VIDEO
CENTER
NETWORKDC OUT
TRIGGER OUT
REMOTE
5V 0.5A (NET)
12V
IN
OUT
0.1A
COMPONENT VIDEO
CENTER
HDMI OUT
(RADIO)
FM antenna
AM antenna
The unit (rear)
Hold down Insert Release
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
30/146
PREPARATIONS ➤ Connecting a network cable or the wireless antenna En 30
Connect the unit to a router (access point) with a network cable, or connect the
supplied wireless antenna for establishing a wireless network connection.
You can enjoy Internet radio or music files stored on media servers, such as PCs andNetwork Attached Storage (NAS), on the unit.
Connecting the network cable
Connect the unit to your router with a commercially-available STP network cable (CAT-5
or higher straight cable).
• If you are using a router that supports DHCP, you do not need to configure any network settings for the unit,as the network parameters (such as the IP address) will be assigned automatically to it. You only need toconfigure the network settings if your router does not support DHCP or if you want to configure the networkparameters manually (p.107).
• You can check whether the network parameters (such as IP address) are properly assigned to the unit in“Network” (p.115) in the “Information” menu.
• Some security software installed on your PC or the firewall settings of network devices (such as a router)may block the access of the unit to the network devices or the Internet. In these cases, configure thesecurity software or firewall settings appropriately.
• Each server must be connected to the same subnet as the unit.
• To use the service via the Internet, broadband connection is strongly recommended.
Connecting the wireless antenna
Connect the supplied wireless antenna to the unit for establishing a wireless networkconnection.
For information on how to connect the unit to a network device wirelessly, see
“Connecting to a network device wirelessly” (p.42).
a Rotate the antenna clockwise.
b Stand the antenna up straight.
• Do not connect the antenna other than the supplied one.
• Do not apply excessive force on the antenna. Doing so may damage it.
• When packing the unit, remove the antenna to prevent damage.
6 Connecting a network cable or the wireless antenna
SPEAKERS
NETWORK(NET)
ZONE2/F.PRESENCE
EXTRASP
WIRELESS
LAN
WAN
Network Attached Storage
(NAS)
Internet
Modem
Router
Network cable
PC
The unit (rear)
Mobile device(such as iPod touchand iPhone)
a
bWIRE
LESS
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
31/146
PREPARATIONS ➤ Connecting other devices En 31
Connecting an external power amplifier
(RX-V777 only)
When connecting an external power amplifier (pre-main amplifier) to enhance speaker
output, connect the input jacks of the power amplifier to the PRE OUT jacks of the unit.
The same channel signals are output from the PRE OUT jacks as from their
corresponding SPEAKERS terminals.
1 FRONT jacksOutput front channel sounds.
2 SURROUND jacksOutput surround channel sounds.
3 SUR. BACK jacksOutput surround back channel sounds. When using only one external amplifier for the surround
back channel, connect it to the SINGLE jack (L side).
4 SUBWOOFER1–2 jacksFor connecting a subwoofer with built-in amplifier. When 2 subwoofers are connected, the samesound is output from them.
5 CENTER jack Outputs center channel sounds.
Connecting recording devices
You can connect video/audio recording devices to the AV OUT jacks. These jacks
output analog video/audio signals selected as the input.
• To copy video/audio from a video device, connect the video device to the AV 5–6 jacks of the unit.
• To copy audio from an audio device, connect the audio device to the AV 5–6 jacks or AUDIO 1–2 jacks ofthe unit.
• Be sure to use the AV OUT jacks only for connecting recording devices.
7 Connecting other devices
Caution
• To prevent the generation of loud noises or abnormal sounds, make sure the followings before making
connections.– Remove the power cable of the unit and turn off the external power amplifier before connecting them.
– When using the PRE OUT jacks, do not connect speakers to the corresponding SPEAKERSterminals.
– When using an external amplifier that does not have the volume control bypass, do not connect otherdevices (except the unit) to the amplifier.
COMPONENTVIDEO
VIDEO
MONITOR OUT
PB
Y
PR
HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)
ANTENNA
FMAM
FRONT CENTER SURROUND
SINGLE
SURROUNDBACK/BI-AMP
SPEAKERS
AV6 AVOUT ZONE OUT SUBWOOFERSUR.BACKSURROUNDFRONT
PRE OUT
CENTER
SINGLE
ZONE 2
NETWORK(NET)
ZONE2/F.PRESENCE
EXTRA SP
CENTER
1
2
(RADIO)
WIRELESS
1 2 3 4 5
The unit (rear)
AUDIO1 AUDIO2
AL
AL
IAL
VIDEO
AV4
AV3
AV2
AV1
(TV)
PBY PR
COMPONENTVIDEO
VIDEO
MONITOR OUT
PB
Y
PR
HDMI 1 HDMI 2 HDMI 3 HDMI 4(BD/DVD)
12
ARC
ANTENNA
FMAM
AV5
VIDEO
AV6 AVOUT ZONE OUT SUBWOSUR.BACKSURROUNDFRONT
PRE OUT
CEN
SINGLE
ZONE 2
DC OUT5V 0.5A
COMPONENT VIDEO
CENT
1
2
HDMI OUT
(RADIO)
R
L
AUDIO
R
L
AUDIOAV OUT
VIDEO
V V
L
R
L
R
L
R
The unit (rear)AV OUT jacks
Video/audio input
Video recordingdevice
Audio recordingdevice
Audio input
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
32/146
PREPARATIONS ➤ Connecting the power cable En 32
Connecting a device compatible with the trigger function
The trigger function can control an external device in conjunction with operating the
unit (such as powering on/off and input selection). If you have a Yamaha subwoofer that
supports a system connection or a device with a trigger input jack, you can use the
trigger function by connecting the external device to the TRIGGER OUT jack.
• You can configure the trigger function settings in “Trigger Output” (p.111) in the “Setup” menu.
After all the connections are complete, plug in the power cable.
AUDIO1 AUDIO2
OPTICAL
OPTICAL
COAXIAL
VIDEO
AV4
AV3
AV2
AV1
(TV)
PBY PR
HDMI 1 HD(BD/DVD)
12
ARC
ANTENNA
AM
AV5
VIDEO
AV6 AVOUT
DC OUT
TRIGGER OUT
REMOTE
5V 0.5A
12V
IN
OUT
0.1A
COMPONENT VIDEO
HDMI OUT
(RADIO)
TRIGGER OUT
12V 0.1A
The unit (rear)
TRIGGER OUT jack
Systemconnection
input
Yamaha subwoofer thatsupports a system connection
8 Connecting the power cable
Before connecting the power cable (General model only)
Set the switch position of VOLTAGE SELECTOR according to your local voltage.
Voltages are AC 110–120/220–240 V, 50/60 Hz.
• Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an ACwall outlet. Improper setting of VOLTAGE SELECTOR may cause damage to the unit and create apotential fire hazard.
UND
SINGLE
SURROUNDBACK/BI-AMP
ZONE2/F.PRESENCE
EXTRA SP
WIRELESS
220V-240V
110V-120V
VOLTAGE SELECTORThe unit (rear)
VOLTAGE SELECTOR
CENTER SURROUND
SINGLE
SURROUNDBACK/BI-AMP
SPEAKERS
NETWORK(NET)
ZONE2/F.PRESENCE
EXTRASP
WIRELESS
To an AC wall outlet
The unit (rear)
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
33/146
PREPARATIONS ➤ Selecting an on-screen menu language En 33
Select the desired on-screen menu language from English
(default), Japanese, French, German, Spanish, Russian, Italian and
Chinese.
1 Pressz (receiver power) to turn on the unit.
2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).
3 Press ON SCREEN.
4 Use the cursor keys to select “Setup” and pressENTER.
5 Use the cursor keys (e / r) to select “Language” andthe cursor keys (q / w) to select the desired
language.
6 To confirm the setting, press ENTER.
7 To exit from the menu, press ON SCREEN.
• The information on the front display is provided in English only.
9 Selecting an on-screen menu language
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
ONE
D
CENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ON SCREEN
ENTER
z
Cursor keys
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
34/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 34
The Yamaha Parametric room Acoustic Optimizer (YPAO) function
detects speaker connections, measures the distances from them to
your listening position(s), and then automatically optimizes the
speaker settings, such as volume balance and acoustic
parameters, to suit your room.
• The YPAO function of the unit adopts the YPAO-R.S.C. (Reflected Sound Control)technology that enables to create natural sound fields like a room specificallydesigned for acoustic perfection.
• Note the following regarding YPAO measurement.– Test tones are output at high volume and may surprise or frighten small children.
– Test tone volume cannot be adjusted.
– Keep the room as quiet as possible
– Stay in a corner of the room behind the listening position so that you do notbecome an obstacle between speakers and the YPAO microphone.
– Do not connect headphones.
1 Pressz (receiver power) to turn on the unit.
2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).
3 Turn on the subwoofer and set the volume to half. Ifthe crossover frequency is adjustable, set it to
maximum.
• If you are using bi-amp connection or Zone2 speakers, set “Power AmpAssign” (p.100) in the “Setup” menu to the appropriate setting beforestarting YPAO.
4 Place the YPAO microphone at your listeningposition and connect it to the YPAO MIC jack on thefront panel.
• Place the YPAO microphone at your listening position (same height as yourears). We recommend the use of a tripod as a microphone stand. You canuse the tripod screws to stabilize the microphone.
10 Optimizing the speaker settings automatically (YPAO)
VOLUME HIGH CUT
CROSSOVER/
MIN MAXMIN MAX
9
YPAO MIC
9
1 2
3
4 5
The unit (front)
YPAOmicrophone
Ear height
YPAO MIC jack
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
N
SCREEN OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
P AR TY D MI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
z
(RX V677)
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
35/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 35
(RX-V677)
The following screen appears on the TV.
This completes the preparations.
See “Measuring at one listening position (single measure)”
(p.36) to start the measurement.
(RX-V777)
The following screen appears on the TV.
Proceed to Step 5.
• To cancel the operation, disconnect the YPAO microphone before starting
the measurement.
• To configure the power amplifier assignment setting, press RETURN andselect “Manual Setup” (p.100).
5 (RX-V777 only) If desired, change the measuringmethod (multi/single).
a Use the cursor keys to select “Multi Position” and press ENTER.
b Use the cursor keys to select a setting and then press ENTER.
Settings
• If you perform the multi measure, the speaker settings will be optimized for you toenjoy surround sound in a wider space.
• If you perform the multi measure, first place the YPAO microphone at the listeningposition you will be seated most frequently.
Yes
Select this option if you will have several listeningpositions or if you want others to enjoy surround sound.You can take measurements at up to 8 differentpositions in the room. The speaker settings will beoptimized to suit the area defined by those positions(multi measure).
No (default)
Select this option if your listening position will always be
fixed. Take the measurements at only one position. Thespeaker settings will be optimized to suit that position(single measure).
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
N
SCREEN OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
P AR TY D MI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ENTER
RETURN
Cursor keys
M i t li t i iti
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
36/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 36
This completes the preparations. See the following page to start the
measurement.
When “Multi Position” is set to “Yes”:
“Measuring at multiple listening positions (multi measure) (RX-V777
only)” (p.37)
When “Multi Position” is set to “No”:
“Measuring at one listening position (single measure)” (p.36)
Measuring at one listening position(single measure)
Follow the procedure below for measurement. It takes about
3 minutes to perform the measurement.
1 To start the measurement, use the cursor keys toselect “Measure” and press ENTER.
The measurement will start in 10 seconds. Press ENTER
again to start the measurement immediately.
• To cancel the measurement temporarily, press RETURN.
The following screen appears on the TV when themeasurement finishes.
• If any error message (such as E-1) or warning message (such as W-1)appears, see “Error messages” (p.40) or “Warning messages” (p.41).
• To check the measurement results, select “Result”. For details, see
“Checking the measurement results” (p.39).
2 Use the cursor keys to select “Save/Cancel” andpress ENTER.
a b
a
a
b
c
d
e
c
d
d e
bac
Multi measure(5 listening positions)
Multi measure(2 listening positions + front/back)
Multi measure(1 listening position + front/back/left/right)
Single measure
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
N
SCREEN OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
ONE
D
CENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ENTER
RETURN
Cursor keys
Measuring at multiple listening positions
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
37/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 37
3 To save the measurement results, use the cursorkeys (e / r) to select “SAVE” and press ENTER.
The adjusted speaker settings are applied.
• To finish the measurement without saving the result, select “CANCEL”.
4 Use the cursor keys (e / r) to select “YES” or “NO”to enable/disable YPAO Volume and press ENTER.
• If YPAO Volume is enabled, the high- and low-frequency levels areautomatically adjusted according to the volume so that you can enjoynatural sounds even at low volume.
• You can also enable/disable YPAO Volume in “YPAO Volume” (p.88) in the“Option” menu.
5 Disconnect the YPAO microphone from the unit.This completes optimization of the speaker settings.
Measuring at multiple listening positions(multi measure) (RX-V777 only)
When “Multi Position” is set to “Yes”, follow the procedure below for
measurement. It takes about 10 minutes to measure 8 listening
positions.
• If any error message (such as E-1) or warning message (such as W-1) appears,see “Error messages” (p.40) or “Warning messages” (p.41).
1 To start the measurement, use the cursor keys toselect “Measure” and press ENTER.
The measurement will start in 10 seconds. Press ENTERagain to start the measurement immediately.
• To cancel the measurement temporarily, press RETURN.
The following screen appears on the TV when the
measurement at the first position finishes.
2 Move the YPAO microphone to the next listeningposition and press ENTER.Repeat Step 2 until measurements at all listening positions
(up to 8) have been taken.
Caution
• The YPAO microphone is sensitive to heat, so should not be placed anywherewhere it could be exposed to direct sunlight or high temperatures (such as on
top of AV equipment).
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
N
SCREEN OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ENTER
RETURN
Cursor keys
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
38/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 38
3 When the measurements at the positions you wantto measure are completed, use the cursor keys to
select “CANCEL” and press ENTER.
When you have taken measurements at 8 listening
positions, the following screen appears automatically.
• To check the measurement results, select “Result”. For details, see“Checking the measurement results” (p.39).
4 Use the cursor keys to select “Save/Cancel” andpress ENTER.
5 To save the measurement result, use the cursorkeys to select “SAVE” and press ENTER.
The adjusted speaker settings are applied.
• To finish the measurement without saving the result, select “CANCEL”.
6 Use the cursor keys (e / r) to select “YES” or “NO”to enable/disable YPAO Volume and press ENTER.
• If YPAO Volume is enabled, the high- and low-frequency levels areautomatically adjusted according to the volume so that you can enjoynatural sounds even at low volume.
• You can also enable/disable YPAO Volume in “YPAO Volume” (p.88) in the“Option” menu.
7 Disconnect the YPAO microphone from the unit.This completes optimization of the speaker settings.
Caution
• The YPAO microphone is sensitive to heat, so should not be placed anywherewhere it could be exposed to direct sunlight or high temperatures (such as ontop of AV equipment).9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
N
SCREEN OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
ONE
D
CENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ENTER
Cursor keys
Checking the measurement results 3
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
39/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 39
Checking the measurement results
You can check the YPAO measurement results.
1 After the measurement, use the cursor keys toselect “Result” and press ENTER.
• You can also select “Result” from “Auto Setup” (p.98) in the “Setup” menu,which displays the previous measurement results.
The following screen appears.
1Measurement result items
2Measurement result details
3 The number of measured positions (when multi
measure is performed) * RX-V777 only
2 Use the cursor keys to select an item.
3 To finish checking the results and return to theprevious screen, press RETURN.
Reloading the previous YPAO adjustmentsWhen the speaker settings you have configured manually are not
suitable, follow the procedure below to discard the manual settings
and reload the previous YPAO adjustments.
1 In the “Setup” menu, select “Speaker”, “AutoSetup”, and then “Result” (p.97).
2 Use the cursor keys to select “Setup Reload” andpress ENTER.
3 To exit from the menu, press ON SCREEN.Wiring
Polarity of each speaker
Reverse: The speaker cable may be connected with thereverse polarity (+/-).
Size
Size of each speaker (cross-over frequency of the
subwoofer)Large: The speaker can reproduce low-frequencysignals effectively.
Small: The speaker cannot reproduce low-frequencysignals effectively.
Distance Distance from the listening position to each speaker
Level Output level adjustment for each speaker
12
3
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ON SCREEN
ENTER
RETURN
Cursor keys
Error messages
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
40/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 40
Error messages
If any error message is displayed during the measurement, resolve the problem and perform YPAO again.
Error message Cause Remedy
E-1: No Front SP Front speakers are not detected.
Follow the on-screen instructions to exit YPAO, turn off the unit, and then check the speaker connections.E-2: No Sur. SP One of the surround speakers cannot be detected.
E-3: No F.PRNS SP One of the presence speakers cannot be detected.
E-4: SBR → SBL A surround back speaker is connected to the R side only.When using only one surround back speaker, you need to connect it to the SINGLE jack (L side). Follow theon-screen instructions to exit YPAO, turn off the unit, and then reconnect the speaker.
E-5: Noisy The noise is too loud.Keep the room quiet and follow the on-screen instructions to start the measurement again. If you select“PROCEED”, YPAO takes the measurement again and ignores any noise detected.
E-6: Check Sur. Surround back speakers are connected, but no surroundspeakers are connected.
Surround speakers need to be connected in order to use surround back speakers. Follow the on-screeninstructions to exit YPAO, turn off the unit, and then reconnect the speakers.
E-7: No MIC The YPAO microphone has been removed.Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start themeasurement again.
E-8: No Signal The YPAO microphone cannot detect test tones.Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start themeasurement again. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or servicecenter.
E-9: User Cancel The measurement has been canceled. Fol low the on-screen instructions to start the measurement again. To cancel the measurement, select “EXIT”.
E-10: Internal Error An internal error has occurred. Follow the on-screen instructions to exit YPAO, turn off and on the unit. If this error occurs repeatedly, contactthe nearest authorized Yamaha dealer or service center.
Warning messages
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
41/146
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 41
Warning messages
If a warning message is displayed after the measurement, you can still save the measurement results by following on-screen instructions.
However, we recommend you perform YPAO again in order to use the unit with the optimal speaker settings.
Warning message Cause Remedy
W-1: Out of PhaseA speaker cable may be connected with the reverse polarity(+/-).
Select “Wiring” in “Result” (p.39) and check the cable connections (+/-) of the speaker identified by“Reverse”.
If the speaker is connected incorrectly:
Turn off the unit and then reconnect the speaker cable.
If the speaker is connected correctly:
Depending on the type of speakers or room environment, this message may appear even i f the speakers areconnected correctly. In this case, you can ignore the message.
W-2: Over Distance
A speaker is placed more than 24 m (80 ft) from the listening
position.
Select “Distance” in “Result” (p.39) and move the speaker identified by “>24.00m (>80.0ft)” within 24 m (80
ft) of the listening position.
W-3: Level ErrorThere are significant volume differences between thespeakers.
Check the usage environment and cable connections (+/-) of each speaker, and the volume of thesubwoofer. We recommend using the same speakers or speakers with specifications that are as similar aspossible.
11 Connecting to a network device wirelessly
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
42/146
PREPARATIONS ➤ Connecting to a network device wirelessly En 42
Connect the unit to a wireless router (access point) or a mobile device by establishing a
wireless connection.
Selecting the connection method
Select a connection method according to your network environment.
■ Connecting with a wireless router (access point)Connect the unit to a wireless router (access point).
You can enjoy Internet radio, AirPlay, or music files stored on media servers (PC/NAS)
on the unit.
For details on connection, see “Connecting the unit to a wireless network” (p.43).
• You cannot use the wireless network connection simultaneously with the wired (network cable) connection(p.30) or Wireless Direct (p.48).
• If the unit and the wireless router (access point) are too far apart, the unit may not connect to a wirelessrouter (access point). In such case, place them close to each other.
■ Connecting without a wireless router (access point)Connect a mobile device to the unit directly.
You can use the application for smartphone / tablet “AV CONTROLLER” to control theunit from mobiles devices or enjoy music files stored on mobiles devices on the unit.
For details on connection, see “Connecting a mobile device to the unit directly
(Wireless Direct)” (p.48).
• You cannot use Wireless Direct simultaneously with the wired (network cable) connection (p.30) or thewireless network connection (p.43).
• When Wireless Direct is enabled, the following functions are not available.– Internet radio
– Network services
– Playback of music stored on media servers (PC/NAS)
• For details on “AV CONTROLLER”, visit the Yamaha website.
11 Connecting to a network device wirelessly
The unit
Wireless router
Mobile device(such as iPhone)
Internet
Modem
The unitMobile device(such as iPhone)
Connecting the unit to a wireless network 4 Use the cursor keys to select “Setup” and press
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
43/146
PREPARATIONS ➤ Connecting to a network device wirelessly En 43
g
There are several methods to connect the unit to a wireless
network.
Select a connection method according to your environment.
■ A: Sharing the iOS device settingYou can easily setup a wireless connection by applying the
connection settings on iOS devices (iPhone/iPad/iPod touch).Before proceeding, confirm that your iOS device is connected to a
wireless router.
• You need iOS device with iOS 5.0 or later. For details on supported devices, see“Supported devices and file formats” (p.131).
1 Pressz (receiver power) to turn on the unit.
2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).
• Operations with TV screen are available only when your TV is connected tothe unit via HDMI.
3 Press ON SCREEN.
4 Use the cursor keys to select Setup and pressENTER.
5 Use the cursor keys (e / r) to select “Network”.
6 Use the cursor keys (q / w) to select “NetworkConnection” and press ENTER.
7 Use the cursor keys (q / w) and ENTER to check“Wireless (Wi-Fi)” and select “OK”.
• The checkmark indicates the current setting.
8 Use the cursor keys (q / w) and ENTER to check“Share Wi-Fi Settings (iOS)” and select “NEXT”.
YesDo you own iOS devices
(iPhone/iPad/iPod touch)?
Yes
A (p.43)
B (p.44)Does your wireless router
(access point) has a WPS
button?
C (p.45)
No
No
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ON SCREEN
ENTER
z
Cursor keys
9 Connect the iOS device to the USB jack and disable ■B: Using the WPS push button
f
1 2 3 4 5 6 7 8 9 10 11
z
-
8/21/2019 Yamaha RX-V677 manual
44/146
PREPARATIONS ➤ Connecting to a network device wirelessly En 44
9 Connect the iOS device to the USB jack, and disablethe screen lock on the iOS device.
10Use the cursor keys (e / r) to select “NEXT” andpress ENTER.
11Tap “Allow” in the message appeared on the iOSdevice.
When the connection process finishes, “Completed”
appears on the TV screen.
12To exit from the menu, press ON SCREEN.
configurationYou can easily set up a wireless connection with one push of the
WPS button.
• This configuration does not work if the security method of your wireless router(access point) is WEP. In this case, use other connection method.
1 Pressz (receiver power) to turn on the unit.
2 Hold down INFO (WPS) on the front panel for 3seconds.
“Press WPS button on Access Point” appears on the frontdisplay.
3 Push the WPS button on the wireless router (accesspoint).
When the connection process finishes, “Completed”
appears on the front display.
If “Not connected” appears, repeat from Step 1 or try
another connection method.
VIDEOHDMI/ 5 V 2 .1 A
VIDEO AUX
M HL 5V 1A2.1A
The unit (front)
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ON SCREEN
ENTER
z
Cursor keys
■ C: Using other connection methods 8 Use the cursor keys ( / ) and ENTER to select the
1 2 3 4 5 6 7 8 9 10 11
z
-
8/21/2019 Yamaha RX-V677 manual
45/146
PREPARATIONS ➤ Connecting to a network device wirelessly En 45
If your wireless router (access point) does not support WPS push
button configuration method, follow the procedure below to
configure the wireless network settings.
1 Pressz (receiver power) to turn on the unit.
2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).
• Operations with TV screen are available only when your TV is connected tothe unit via HDMI.
3 Press ON SCREEN.
4 Use the cursor keys to select “Setup” and pressENTER.
5 Use the cursor keys (e / r) to select “Network”.
6 Use the cursor keys (q / w) to select “NetworkConnection” and press ENTER.
7 Use the cursor keys (q / w) and ENTER to check“Wireless (Wi-Fi)” and select “OK”.
• The checkmark indicates the current setting.
8 Use the cursor keys (q / w) and ENTER to select thedesired connection method and select “NEXT”.
The following connection methods are available.
WPS ButtonYou can set up a wireless connection with theWPS button while viewing the TV screen. Followthe instructions displayed on the TV screen.
Share Wi-FiSettings (iOS)
See “Sharing the iOS device setting” (p.43).
Access PointScan
You can set up a wireless connection bysearching for an access point. For details onsettings, see “Searching for an access point”(p.46).
Manual Setting
You can setup a wireless connection by enteringthe required information (such as SSID)
manually. For details on settings, see “Setting upthe wireless connection manually” (p.46).
PIN Code
You can set up a wireless connection by enteringthe unit’s PIN code into the wireless router(access point). The method is available if thewireless router (access point) supports the WPSPIN code method. For details on settings, see“Using the PIN code” (p.47).
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance,which allows easy establishment of a wireless home network.
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ON SCREEN
ENTER
z
Cursor keys
❑ Searching for an access point
If l “A P i S ” h i h d h
❑ Setting up the wireless connection manually
If l “M l S i ” h i h d h
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
46/146
PREPARATIONS ➤ Connecting to a network device wirelessly En 46
If you select “Access Point Scan” as the connection method, the
unit starts searching for access points. After a while, the list of
available access points appears on the TV screen.
1 Use the cursor keys and ENTER to check thedesired access point and select “NEXT”.The wireless connection setting screen appears on the TV.
2 Use the cursor keys and ENTER to enter thesecurity key and select “NEXT”.
3 Use the cursor keys (e / r) to select “CONNECT”and press ENTER to start the connection process.When the connection process finishes, “Completed”
appears on the TV screen.
If “Not connected” appears, repeat from Step 1 or try
another connection method.
4 To exit from the menu, press ON SCREEN.
If you select “Manual Setting” as the connection method, the
wireless connection setting screen appears on the TV.
You need to setup the SSID (network name), encryption method
and security key for your network.
1 Use the cursor keys and ENTER to enter the SSID ofthe access point and select “NEXT”.
2 Use the cursor keys (q / w) and ENTER to check thesecurity method of the access point and select
“NEXT”.
Settings
None, WEP, WPA-PSK (TKIP), WPA-PSK (AES), WPA2-PSK (AES),Mixed Mode
9 0 ENTMEMORY
5 6 87
1 2 3 4
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN OPTION
TOPMENU
MUTEP ROGR AM V OL UM E
POP-UP/MENU
PURE DIRECT
STRAIGHT
I NF O S LE EP
MUSIC
NET
PARTY HDMI OUT
TUNER
MAIN ZONE 2
USB
MODE
SCENE
BDDVD
TV NET RADIO
HDMI
AV
AUDIO
5
65
V-AUX
1 2 3 4
1 2
1 2
3 4
SUR. DECODE
0 ENTMEMORY
6
1 2 3 4
M VI
ENHAN
T NIN RE ET
DI PLA
OPTION
TOPMENU
P ROGR AM V OL UM E
POP-UP/MENU
P RE DIRE
TRAI
INF LEE
M I
NET
PARTY HDMI OUT
TUNER
NE
D
SCENE
DDVD
O
HDMI
AV
5
65
-AUX
1 2 3 4
1 2
1 2
3 4
R . D E D
ON SCREEN
ENTER
Cursor keys
3 Use the cursor keys and ENTER to enter the❑ Using the PIN code
If you select “PIN Code” as the connection method the list of
1 2 3 4 5 6 7 8 9 10 11
-
8/21/2019 Yamaha RX-V677 manual
47/146
PREPARATIONS ➤ Connecting to a network device wirelessly En 47
3 ysecurity key and select “NEXT”.
If you select “None” in Step 2, this setting is not available.
Proceed to Step 4.
If you select “WEP”, enter either 5 or 13 character string, or10 or 26 hexadecimal digits.
If you select other method, enter either 8 to 63 character
string, or 64 hexadecimal digits.
4 Use the cursor keys (e / r) to select “CONNECT”and press ENTER to start the connection process.
When the connection process finishes, “Completed”appears on the TV screen.
If “Not connected” appears, check that all the information is
entered correctly, and repeat from Step 1.
5 To exit from the menu, press ON SCREEN.
If you select “PIN Code” as the connection method, the list of
available access points appears on the TV screen.
1 Use the cursor keys and ENTER to check thedesired access point and select “NEXT”.
The PIN code of the unit appears on the TV screen.
2 Enter the unit’s PIN code into the wireless router(access point).
For details on settings, refer to the instruction manual of the
wireless router (access point).
3 Use the cursor keys (e / r) to select “CONNECT”and press ENTER to start the connection process.When the connection process finishes, “Completed”
appears on the TV screen.
If “Not connected” appears, repeat from Step 1 or try
another connection method.
4 To exit from the menu, press ON SCREEN.
9 0 ENTMEMORY
5 6 �