Download - X-IE-G DATA SHEET - hilti.com.om
April 2021
X-IE-GDATA SHEETInsulation fastener
04/2021 2www.hilti.group
X-IE-G
X-IE-G 6 and X-IE-G 9 insulation fasteners
Product data
X-IE-G 6 Product description• Suitable for a wide range of insulation materials –
Soft mineral wool, mineral wool, EPS, XPS, PIR, PUR, soft core multilayer board, rigid core multilayer board
• Suitable for 25–200 mm thick insulation• Very high thermal efficiency in a one-step solution• No holes in the fastener shank – helping prevent mold and
moisture penetration in the insulation material• Gauge included for easy visual control of correct fastener
driving depth• Specially-designed 90 mm disc diameter for soft mineral
wool, providing excellent clamping of the insulationX-IE-G 9
Dimensions
Ø
Ls
Designation Diameter Ø Nail length L sX-IE-G 6 60 mm 36 mmX-IE-G 9 90 mm 36 mm
Material properties for plastic parts
Element Designation Material Color Other propertiesPlate X-IE-G 6 HDPE Colorless UV stabilized materialPlate X-IE-G 9 HDPE Black UV stabilized material
3 04/2021www.hilti.group
X-IE-G
Material properties for carbon steel parts
Element Designation Material Coating Minimum coating thickness
Hardness
Nail X-P 36 G3 Carbon steel Zinc 2 µm 57.5 HRC
Applications
Curtain wall insulation Ceiling insulation Basement perimeterinsulation
Base materials
Solid sand- lime masonry
Solid brick
Approvals and certificates
Authority Approval / certificate no. Date of issue Country of issueSocotec 180668080000010 09/ 2018 France
Not all information presented in this product data sheet might be subject to approval / certificate content. Please refer to approval / certificate for further information.
Soft concrete
Medium concrete
04/2021 4www.hilti.group
X-IE-G
• The intended use comprises fastening in dry conditions.
• During construction, exposure to UV due to solar radiation of the fixing element not protected by rendering shall not exceed the time of 6 weeks.
• The temperature during installation of the fixing element shall not be less than 5 °C.
Load condition
Environmental conditions
Staticquasi-static
• Soft core multilayer board: hard top layer with insulation core of mineral wool • Rigid core multilayer board: hard top layer with insulation core of EPS, XPS, PIR,
PUR
Fastened materials
Soft mineral wool
Mineral wool
EPS XPS PIR, PUR
Soft and rigid core multilayer board
Application requirements
Fastened material properties
tI
Fastened material
Compressive strength
Fastened material thickness tl
Soft mineral wool < 500 kN / m2 25–200 mmMineral wool < 500 kN / m2 25–200 mmEPS, XPS, PIR, PUR, soft core multilayer board
< 500 kN / m2 25–200 mm
Rigid core multilayer board < 500 kN / m2 19–197 mm
5 04/2021www.hilti.group
X-IE-G
Fastener edge distance and spacing in base material
cs
sc
ce
c e
Minimum corner distance ce
Minimum edge distance c
Minimum fastener spacing distance s
100 mm 75 mm 100 mm
Number of fasteners per m²
Fastened material Fastened material weight Minimum number of fasteners per m²
Soft mineral wool, mineral wool, EPS, XPS, PIR, PUR,soft core multilayer board, rigid core multilayer board
< 50 kg/m2 450–75 kg/m2 5> 75 kg/m² 7
Fastened material Fastened material density Minimum number of fasteners per m²
Soft mineral wool, mineral wool, EPS, XPS, PIR, PUR,soft core multilayer board, rigid core multilayer board
< 10 kg/m3 410–15 kg/m3 5> 15 kg/m3 7
Please consult insulation material supplier
Fastener edge distance and spacing in insulation material
Base material properties
tII
Base material Base material strength
Base material thickness tII
Soft, medium concrete fcc = 15–45 N / mm2 ≥ 80 mm
Tough concrete fcc = 45–65 N / mm2 ≥ 80 mmSolid sand-lime masonry fb = 15–45 N / mm2 –
Solid brick fb = 28–45 N / mm2 –Steel fu = 360–450 N / mm2 4–6 mm
04/2021 6www.hilti.group
X-IE-G
Performance data
Recommended resistance under tension and shear load
N
V
Base material TensionNrec
ShearVrec
Soft, medium concrete 0.1 kN 0.1 kNSolid sand-lime masonry 0.1 kN 0.1 kNSolid brick 0.1 kN 0.1 kN
• For more details in relation to base material properties, please refer to the chapter
Fastener selection guide in the Direct Fastening Technology Manual (DFTM). • The above data value for solid sand-lime masonry and solid brick are based on
laboratory and field experience. Because of the wide variety of types and forms of masonry in use worldwide, users are advised to carry out tests on site or on masonry of the type and form on which the fastenings are to be made.
• The above data refers to the fastener pull-out failure mode. • For pull-over under tension load please consult insulation material supplier.
Stick rate estimation
Designation Soft, medium concrete15 ≤ fc,cube ≤ 45 N / mm2
X-IE-G 6, X-IE-G 9 Up to 90 %
The stick rate indicates the percentage of nails that were driven correctly to carry a load. Stick rate can vary from the above values depending on job site conditions
Thermal efficiency according to EOTA TR 025
Application Insulation thicknesstI
Point thermal transmittanceϰ
Curtain wall insulation 60–90 mm 0.002 W/K100–200 mm 0.001 W/K
Ceiling insulation 60–90 mm 0.002 W/K100–200 mm 0.001 W/K
Basement perimeter insulation
60 mm 0.003 W/K70–100 mm 0.002 W/K120–200 mm 0.001 W/K
7 04/2021www.hilti.group
X-IE-G
■ = recommended, ■ = feasible
Designation Tools Gas can
GX-IE GX-IE XL GC 52
X-IE-G 6X-IE-G 6-25 X-IE-G 6-140 ■ ■ ■X-IE-G 6-150 X-IE-G 6-200 ■ ■
X-IE-G 9X-IE-G 9-40 X-IE-G 9-140 ■ ■ ■X-IE-G 9-150 X-IE-G 9-200 ■ ■
System recommendation
Tool and energy recommendation
• For more details, please refer to the chapter Accessories and consumables compatibility in the Direct Fastening Technology Manual (DFTM).
04/2021 8www.hilti.group
X-IE-G
Fastener selection
Fastened material Insulation thickness tI
Designation Nail Item number
Soft mineral wool
40 mm X-IE-G 9-40 X-P 36 G3 217215450 mm X-IE-G 9-50 X-P 36 G3 217215560 mm X-IE-G 9-60 X-P 36 G3 217215680 mm X-IE-G 9-80 X-P 36 G3 2172157100 mm X-IE-G 9-100 X-P 36 G3 2172158120 mm X-IE-G 9-120 X-P 36 G3 2172159140 mm X-IE-G 9-140 X-P 36 G3 2163823150 mm X-IE-G 9-150 X-P 36 G3 2192919160 mm X-IE-G 9-160 X-P 36 G3 2163824180 mm X-IE-G 9-180 X-P 36 G3 2163825200 mm X-IE-G 9-200 X-P 36 G3 2163826
Fastened material Insulation thickness tI
Designation Nail Item number
Mineral wool, EPS, XPS, PIR, PUR, soft core multilayer board
25 mm X-IE-G 6-25 X-P 36 G3 219291430 mm X-IE-G 6-30 X-P 36 G3 216381040 mm X-IE-G 6-40 X-P 36 G3 221251450 mm X-IE-G 6-50 X-P 36 G3 221251560 mm X-IE-G 6-60 X-P 36 G3 216381370 mm X-IE-G 6-70 X-P 36 G3 216381475 mm X-IE-G 6-75 X-P 36 G3 219291580 mm X-IE-G 6-80 X-P 36 G3 216381590 mm X-IE-G 6-90 X-P 36 G3 2192916100 mm X-IE-G 6-100 X-P 36 G3 2163816120 mm X-IE-G 6-120 X-P 36 G3 2192917130 mm X-IE-G 6-130 X-P 36 G3 2192918140 mm X-IE-G 6-140 X-P 36 G3 2163817150 mm X-IE-G 6-150 X-P 36 G3 2163818160 mm X-IE-G 6-160 X-P 36 G3 2163819180 mm X-IE-G 6-180 X-P 36 G3 2163820200 mm X-IE-G 6-200 X-P 36 G3 2163821
9 04/2021www.hilti.group
X-IE-G
Fastened material Insulation thickness tI
Designation Nail Item number
Rigid core multilayer board
19–22 mm X-IE-G 6-25 X-P 36 G3 219291424–27 mm X-IE-G 6-30 X-P 36 G3 216381034–37 mm X-IE-G 6-40 X-P 36 G3 221251444–47 mm X-IE-G 6-50 X-P 36 G3 221251554–57 mm X-IE-G 6-60 X-P 36 G3 216381364–67 mm X-IE-G 6-70 X-P 36 G3 216381469–72 mm X-IE-G 6-75 X-P 36 G3 219291574–77 mm X-IE-G 6-80 X-P 36 G3 216381584–87 mm X-IE-G 6-90 X-P 36 G3 219291694–97 mm X-IE-G 6-100 X-P 36 G3 2163816114–117 mm X-IE-G 6-120 X-P 36 G3 2192917124–127 mm X-IE-G 6-130 X-P 36 G3 2192918134–137 mm X-IE-G 6-140 X-P 36 G3 2163817144–147 mm X-IE-G 6-150 X-P 36 G3 2163818154–157 mm X-IE-G 6-160 X-P 36 G3 2163819174–177 mm X-IE-G 6-180 X-P 36 G3 2163820194–197 mm X-IE-G 6-200 X-P 36 G3 2163821
• Insulation board thickness tolerance: ±3 mm
• Soft mineral wool, mineral wool: for intermediate thicknesses use next shorter fastener, example: for mineral wool insulation thickness 110 mm, use X-IE 6-100
• EPS, XPS, PIR, PUR, soft core multilayer board: for intermediate thicknesses use next longer fastener, example: for PIR insulation thickness 110 mm, use X-IE 6-120
• Rigid core multilayer board: for thicknesses not specified, please contact Hilti
04/2021 10www.hilti.group
X-IE-G
Fastening inspection
tI
x hET Designation Embedment depth hET
Distance between nail head and X-IE plate x
X-IE-G 6-25 12 – 19 mm 3 – 10 mmX-IE-G 6-30 12 – 19 mm 3 – 10 mmX-IE-G 6-40, X-IE-G 9-40 12 – 19 mm 14 – 21 mmX-IE-G 6-50, X-IE-G 9-50 12 – 19 mm 24 – 31 mmX-IE-G 6-60, X-IE-G 9-60 12 – 19 mm 34 – 41 mmX-IE-G 6-70 12 – 19 mm 44 – 51 mmX-IE-G 6-75 12 – 19 mm 49 – 56 mmX-IE-G 6-80, X-IE-G 9-80 12 – 19 mm 54 – 61 mmX-IE-G 6-90 12 – 19 mm 64 – 71 mmX-IE-G 6-100, X-IE-G 9-100 12 – 24 mm 74 – 81 mmX-IE-G 6-120, X-IE-G 9-120 12 – 24 mm 94 – 100 mmX-IE-G 6-130 12 – 24 mm 104 – 111 mmX-IE-G 6-140, X-IE-G 9-140 12 – 24 mm 114 – 121 mmX-IE-G 6-150, X-IE-G 9-150 12 – 24 mm 124 – 131 mmX-IE-G 6-160, X-IE-G 9-160 12 – 24 mm 134 – 141 mmX-IE-G 6-180, X-IE-G 9-180 12 – 24 mm 154 – 161 mmX-IE-G 6-200, X-IE-G 9-200 12 – 24 mm 174 – 181 mm
Fastening quality assurance
11 04/2021www.hilti.group
X-IE-G
Setting depth control and power tool adjustment
Check setting depth with the gaugeimmediately after fastening
• Visible setting failures must be replaced with a new fastener, not in the same hole
• These are abbreviated instructions which may vary by application. • ALWAYS review / follow the instructions accompanying the product