Download - Validation of water
1
Validation of Water(Demineralised, Distilled and Water for Injection)
PRESENTED BY
Anil Kumar
M . Pharm (DRA)
BBAU LUCKNOW 226025
2 CONTENTS
Objectives
Introduction
Validation & System Qualification
Monitoring
Maintenance
Revalidation & Change control
Validation report
Validation documentation
Summary
3 Objective
General information on water systems Design and engineering aspects of water systems Inspection of water systems The need for water quality manual reason for usage of pharmaceutical water supply systems. The technical requirements for water supply systems. Different types of water supply systems. Validation requirements. Qualification & inspection requirement
4 Introduction
Water may be referred to as ‘the elixir of life’ – In the pharmaceutical industry for which the quality of water is critical and a high priority.
Water is an essential ingredient of various pharmaceutical preparations and is also used to clean process equipment and hence, plays a pivotal role in pharmaceutical processing's.
Water is the most widely used raw material in the manufacture of Active Pharmaceutical Ingredients (API),in intermediates, in finished dosage forms.
Water is thus an important raw material in GMP and in validating the manufacturing process.
5 Continued…….Why purification?
Although tap water is reasonably pure, it is always variable due to seasonal variations, regional variation in quality.
One must remove impurities and control microbes to avoid contamination of products.
Pretreatment depends on quality of feed water.
6 Continued…….Quality of water should be specific for product quality.
Water contains, Organic and inorganic impurities Microbial contamination Endotoxin Particulate contamination Low quality of water can lead to product degradation product contamination loss of product and profit
7 TYPES OF WATERDifferent grades of Water for Pharmaceutical Purposes-each type has its on characteristic for all parameters.
Potable water Purified water Water for injection(WFI) Sterile water for injection, inhalation, irrigation. Bacteriostatic water for injections.
8 Potable water Used in early stages of chemical synthesis.
Used early stages of equipment cleaning.
Sources: Public water supply, wells or combination of >1 of these
Must meet requirement of USEPA(40 CFR 141)
Seasonal variations of quality may occur and must be considered for treatment before usages.
9 Purified water ( Demineralised, Distilled )
Used as excipients in manufacturing of Pharmaceuticals.
Used for equipment cleaning
Preparation of bulk chemicals.
Prepared using potable water as feed.
Types of Purification: Deionisation, Distillation, Ion exchange, Reverse osmosis, filtration.
Must meet ionic, organic chemical and microbial requirements.
System that produce, store and circulate water under ambient conditions are susceptible to bio films. This can be provided by frequent sanitization and monitoring.
10 Water for injections Used as excipient in manufacturing of potentials.
Used for equipment cleaning esp. product contact surfaces of sterile products.
Preparation of sterile bulk chemicals.
Prepared using purified water as feed.
Method of preparation is multicolumn distillation.
Must meet ionic, organic chemical, microbial and endotoxins requirements.
Factors like microbial contamination and endotoxins should be controlled by circulation, frequent sanitization and monitoring.
11 DIFFERENT EQUIPMENTS AND COMPONENTS FOR WATER SYSTEM Piping
Valves
Pumps
Pressure gauges
Heat exchangers
Distillation unit
Filters
Deionizers
Sensors
Auxiliary equipment
12 VALIDATION CONCEPT
To prove the performance of processes or systems under all conditions expected to be encountered during future operations.
To prove the performance, one must demonstrate (document) that the processes or systems consistently produce the specified quantity and quality of water when operated and maintained according to specific written operating and maintenance procedures.
validation involves proving-
1. Engineering design
2. Operating procedures and acceptable ranges for control parameters
3. Maintenance procedures to accomplish it
13 Continued……. the system must be carefully,
-designed
-installed
-tested during processing, after construction, and under all operating conditions.
Variations in daily, weekly and annual system usage patterns must be validated.
14 WHY VALIDATION OF WATER SYSTEM?To ensure reliable, consistent production of water of required
qualityTo operate system within design capacityTo prevent unacceptable microbial, chemical and physical
contamination during production, storage and distributionTo monitor system performance, storage and distribution systems
15 Water System QualificationValidation Master Plan
User Requirement Specification
Design Qualification
Operation Qualification
17 DESIGN QUALIFICATION (DQ)DQ is documented the design of the system & will include : Functional Specification.(Storage, purification, etc) Technical/Performance specification for equipment.(requirements of
water volume and flow, define pumps and pipe sizes ) Detailed layout of the system.
Quality attribute of input water
Required plant output capacity
Selection of membrane
Designing of holding tanks pumps, heat exchangers and piping.
Design must be in compliance with GMPs and other regulatory requirements.
18 Operational QualificationThe purpose of OQ is to establish, through documented testing, that all
critical components are capable of operating within established limits and tolerances.
Operation Qualification Checks-
Identification of dead legs
Slope verification
Weld inspection
Pressure test
Passivation
The purpose of OQ is also to verify and document that the water supply system provides acceptable operational control under “at-rest” conditions.
19 Installation QualificationIQ is in the form of checklist and it should include-
Water velocity test
Turbulence flow test (Reynolds number)
Quality attribute of output water
Prepare operational SOP
Prepare cleaning and sanitation SOP
Design action and alert limit
Collection and collation of supplier operating and working instructions and maintenance requirements
20 Performance Qualification
The purpose of PQ is to verify and document that water supply system provides acceptable control under ‘ Full Operational ‘ conditions.
Qualification phases
Phase I (investigational step): sampling and testing (4-6 weeks)
Phase II (verification step): sampling and testing (2-4 weeks)
Phase III (satisfactory completion step): sampling and testing (Yearly activity, seasonal monitoring)
Establish action and alert limit
PQ should follow successful completion of IQ and OQ.
21 MONITORING Monitoring and feed back data are important in maintaining the
performance systems. Monitoring parameters include: Flow, pressure, temperature, conductivity, TOC
Samples taken: From points of use, and specific sample points In a similar way how water is used in service
Tests should include physical, chemical and microbial attributes
For example, stable state can be achieved by applying automatic continuous monitoring of TOC and conductivity of the water system. They are the major quality attributes of water by which organic and inorganic impurities can be determined.
22 MAINTENANCESpecified limits for purified water and water for injection
cfu* = colony forming units; ppb** = parts per billions;
EU*** = endotoxin units
Parameter Purified water Water for injection
Conductivity
< 1.3 μs/cm at 25 °C < 1.3 μs/cm at 25 °C
pH 5.0-7.0 5.0-7.0
Bacteria < 100 cfu*/ml < 10 cfu/100ml
Total organic carbon < 500 ppb** < 500 ppb
Endotoxins N/A < 0.25 EU***/ml
23 CONTINUED…
A controlled, documented maintenance covering :
Defined frequency with plan and instructions
Calibration programme
SOPs for tasks
Control of approved spares
Record and review of problems and faults during maintenance
24 CONTINUED…
System sanitization and bioburden control
Systems in place to control proliferation of microbes
Techniques for sanitizing or sterilization
Consideration already during design stage – then validated
Special precautions if water not kept in the range of 70 to 80 degrees Celsius
25 REVALIDATION & CHANGE CONTROL Once the validation is completed, the standard operating procedures
(SOPs) are formalized.
Routine operation should be performed according to the established SOP.
If any deviation from SOP observed, determine the change and their impact on whole system
Revalidation and evaluation should be performed depending upon the impact of the change on system.
26 VALIDATION REPORT Written at the conclusion of the equipment IQ, OQ and at
completion of process validation.
Will serve as primary documentation for FDA regulatory inspection
Will serve as reference document when changes to the system are occurred and revalidation is needed.
27 VALIDATION DOCUMENTATION Verification of design documentation, including
o Description of installation and functionso Specification of the requirements
Instructions for performance control Operating procedures Maintenance instructions Maintenance records Training of personnel (program and records) Environmental records Inspection of plant
Finally certification (Sign Off) by Engineering, User (Production) and QA Heads.
28 SUMMARY
Validation of water (demineralized, distilled and water for injection): Play a major role in the quality of pharmaceuticals. Must be designed properly by professionals. Must be validated as a critical system.
29 SUGGESTED READING Munson, T.E. “FDA View on Water System Validation.”
Proceedings of the Pharm. Tech. Conference 10-12 September 1985.
“FDA : Water for Pharmaceutical Purposes.” Inspection Technical Guide 1986 No. 46. Rockville, Md., USA. Food and Drug Administration, Public Health Services, Department of Health and Human Services.
Rakesh Pahwa1*, Mona Piplani1, “Validation Aspects of Water Treatment Systems for Pharmaceutical Products”, Tropical Journal of Pharmaceutical Research, February 2010; 9 (1): 81-90
Vineet sharma, ”Design, Qualification, and Validation of Water Systems”, Originally published in the November, 2004 issue of the Journal of Validation Technology.