Trailer TestingTrailer Testing
FACTS AND FIGURES FACTS AND FIGURES
CVSA ROADCHECK June 2-4, 2009
57,013 vehicles inspected
19.6% vehicles were placed Out Of Service
11.6% sidelined for Light System
24.7% sidelined for Brake Adjustment
26.9% sidelined for Brake System
CVSA determined 60% of brake OOS could have been corrected in the pre trip inspection
FACTS AND FIGURES FACTS AND FIGURES
• LIGHTING ISSUES
• 90% of discarded incandescent lamps were operational
• Majority of electrical circuit problems are caused by:
• Poor connections
• Road treatment chemicals
FACTS AND FIGURES FACTS AND FIGURES
• BRAKE ISSUES
• Automatic slacks
• Must still be maintained & adjusted
• Brake Inspection
• Technician must be at the axel to witness movement
FACTS AND FIGURES FACTS AND FIGURES
• ABS ISSUES
• Majority of ABS problems are sensor related
• Over 50% of ECU’s returned under warranty were functional
• ABS operation is now being checked during State DOT Inspections
FACTS AND FIGURESFACTS AND FIGURES
•TMC Survey
• 18% of technicians time is spent on diagnostics
• Pro-active maintenance is less costly than road repairs
• The electrical and air braking systems on today's trailers require diagnostic equipment
FACTS AND FIGURESFACTS AND FIGURES
• TMC Goals
• Reduce vehicle downtime
• Diagnostic Equipment must be easy to operate
• Diagnostic equipment should have less than one year payback
FACTS AND FIGURES FACTS AND FIGURES •Trailer testing and maintenance practices need to protect the trailer systems from premature failure
•This means applying regulated known electrical power and air pressures during the testing
• Excessive and non-regulated 12v power damages wiring, lighting components, and ABS electronics.
• Excessive air pressure stresses the air system components. • Low power and low air applications are not reliable for consistent testing.
For Your Safety, Chock Wheels and Observe Company Policies For Wearing Safety Equipment.
For Your Safety, Chock Wheels and Observe Company Policies For Wearing Safety Equipment.
COMMON LIGHT TESTINGCOMMON LIGHT TESTING
• High voltages over 13.8v create half life conditions on lighting and ABS components
• Unregulated voltage spikes (battery chargers) cause damage
• Low voltages cause dim lights and none operative electronics
IF there is an unreliable 12 volt dc power source…
COMMON LIGHT TESTINGCOMMON LIGHT TESTING
IF all circuits are powered on together…
• Circuit shorts will disguise other problems
• Non-functional elements will not be obvious in dual element lamps
• Incorrect wired lamps will not be seen
PROPER LIGHT TESTING PROPER LIGHT TESTING
• Observe circuit voltage & amperage
• Technician must verify each lamp operation and location
• Circuit faults will be discovered
• Open
• Short
• Open ground
• Chassis ground
• Brake light and Auxiliary electrical circuits are critical for ABS operation
•Auxiliary is primary power and is the Power Line Carrier (PLC)
•The Brake circuit is secondary power and activates ECU operation
OPERATE ONE CIRCUIT AT A TIME
LIGHT TESTING LIGHT TESTING
COMMON TRAILER BRAKE TESTING
COMMON TRAILER BRAKE TESTING
Emergency air system releases the parking brakes and is the supply for service operation.
Service (brake) system is the control system by drawing air from the supply system thru the relay valve.
• IF unregulated air pressure is being applied…• Excessive Pressures cause damage• Insufficient Pressure causes inaccurate results
• Brake Compounding…• Damage slacks
• Create air leaks
• Potential for technician injury
PROPER TRAILER BRAKE TESTING
PROPER TRAILER BRAKE TESTING
IDEAL testing duplicates the tractor operation
• Use regulated air pressure matching tractor operation • Emergency/supply application of 110-120 psi
• Service/control application at 85-90 psi
• Equals a panic stop
• Consistent service pressure is required for reliable and accurate brake adjustment
For Your Safety, Chock Wheels Before Applying Air.
For Your Safety, Chock Wheels Before Applying Air.
PROPER TRAILER BRAKE TEST PROCESS
PROPER TRAILER BRAKE TEST PROCESS
VISUAL INSPECTION OF BRAKE MOVEMENT AT AXLE IS REQUIRED
1. Apply emergency (supply) air
2. Service brake (control) application requires full supply pressure• Cycle air application • Make slack adjustments
3. Air leak test with applied emergency and service air• Air loss on one side is external • Equalizing air pressure is internal seal failure
FEDERAL allowable air loss…• 3 psi/minute on emergency(supply) air system• 2 psi/minute on service air system
BRAKE TEST BRAKE TEST
ABS FACTSABS FACTS
Beginning in 1998 all new commercial trailers and dollies were equipped with the blink code style ABS.
The Power Line Carrier (PLC) style ABS was mandated in 2001. All have ABS warning lights indicating operation status.
As of 2009, approximately 30% of all trailers and dollies have ABS.
ABS testing requires filtered regulated 12 volt dc power from a battery or power supply.
ABS FACTSABS FACTS• TMC has (2) Recommended Practices for ABS
operation:
• RP 137 specifies the tractor Auxiliary output voltage to be a minimum of 10 volts measured at the vehicle cable
trailer plug.
• RP 141 specifies 8.5v is required at the ABS Electronic Control Unit with the entire trailer systems powered.
NOTE:
The ABS Electronic Control Unit (ECU) will not power up with low voltage.
ABS OPERATIONABS OPERATION
ANTILOCK BRAKE SYSTEM (ABS) operation depends upon the Auxiliary electrical and Brake light circuits.
• Auxiliary circuit is the primary power of the Electronic Control Unit (ECU). • When the ignition switch is turned on, the auxiliary circuit is energized.
• The ECU commences a self test (valve clicks)• The ABS warning light turns on.
• Stays on with active fault present• Turns off without a active fault
• Brake circuit controls ABS operation• Activates ABS operation whenever brakes are applied• Backup power whenever Auxiliary power is not present (momentary delay occurs before the ECU is activated).
RECOMMENDED ABS TEST PROCESS
RECOMMENDED ABS TEST PROCESS
•The PLC style ABS can be fully tested at the 7w nose socket.
FIRST:
• Energize Brake circuit to verify good operation. The valves will click and the ABS warning lamp will illuminate.
• Initial amperage will include brake lights, ECU load, and ABS warning lamp.
• If ABS lamp turns off, the brake lights and ECU amperage load will be displayed.
RECOMMENDED ABS TEST PROCESS
RECOMMENDED ABS TEST PROCESS
SECOND:
• Energize Auxiliary circuit for ABS.
• If ABS valves do not click, then…•ECU is faulty or Auxiliary circuit has a fault
• If ABS valves do click without warning lamp, then…•ABS lamp has a fault
• If the ABS warning lamp stays on with Auxiliary power, then…• there is an active ABS fault.
• Initial amperage will include ECU load and ABS warning lamp
• If ABS lamp turns off, the ECU amperage will be displayed
ABS TEST ABS TEST
COMPREHENSIVE TRAILER TESTING
COMPREHENSIVE TRAILER TESTING
• Single tool with diagnostic features• One person operation that is simple to use• Consistent process• Perform trailer DOT test within 10 minutes including brake adjustments• Reduce repair costs because of accurate diagnostics• Improve on time delivery with road worthy equipment• Reduce road costs including downtime, OOS violations, road service
ONE TOOL • ONE PERSON • ONE PROCESS
OVERVIEWOVERVIEW
GOOD MAINTENANCE=
GOOD BUSINESS
GOOD MAINTENANCE=
GOOD BUSINESS
CUSTOMER COMMENT:
“We are using the INSPECTOR in the shop on each trailer that comes in for service. When we make a repair, we are also using it post-repair to certify expected results. We know the repairs are effective and the unit is ready for duty. I just believe our less-experienced techs benefit from the tool and I sleep better at night.”
REFERENCESREFERENCES• Federal Motor Carrier Safety Administration Rules & Regulations
– http://www.fmcsa.dot.gov/ – http://www.fmcsa.dot.gov/rules-regulations/topics/IEP/IMODAL-FINAL.pdf
• Commercial Vehicle Safety Alliance (CVSA)– ABS - http://www.cvsa.org/programs/documents/air_brakes/ABS%20Inspection%20Flyer.pdf– Operation Air Brake - http://www.cvsa.org/programs/op_airbrake.aspx
• National Highway Traffic Safety Administration (NHTSA)– http://www.nhtsa.gov
• Technology & Maintenance Council (TMC)– http://www.truckline.com
• Canadian Transportation Equipment Association (CTEA)- http://www.ctea.ca