Download - Thevenin's Theorem_ Network Theorems
-
8/3/2019 Thevenin's Theorem_ Network Theorems
1/15
THEVENINS THEOREM
INTRODUCTION
THEVENINS EQUIVALENT CIRCUIT
PRESENTATION OF THEVENINS THEOREM
PROOF OF THEVENINS THEOREM
WORKED EXAMPLE 2
WORKED EXAMPLE 3
WORKED EXAMPLE 4
SUMMARY
INTRODUCTION
Thevenins theorem is a popular theorem, used often for analysis of electronic circuits. Its theoretical
value is due to the insight it offers about the circuit. This theorem states that a linear circuit containing one
or more sources and other linear elements can be represented by a voltage source and a resistance. Using
this theorem, a model of the circuit can be developed based on its output characteristic. Let us try to find
out what Thevenins theorem is by using an investigative approach.
Go To Top of the Page
THEVENINS EQUIVALENT CIRCUIT
In this section, the model of a circuit is derived based on its output characateristic. Let a circuit be
represented by a box, as shown in Figure 8. Its output characteristic is also displayed. As the load resistor
is varied, the load current varies. The load current is bounded between two limits, zero and Im, and the
load voltage is bounded between limits,EVolts and zero volts. When the load resistor is infinite, it is an
open circuit. In this case, the load voltage is at its highest, which isEvolts and the load current is zero.
This is the point at which the output characteristic intersects with the Y axis. When the load resistor is of
zero value, there is a short circuit across the output terminals of the circuit and in this instance, the load
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 1/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
2/15
current is maximum, specified asIm and the load voltage is zero. It is the point at which the output
characteristic intersects with the X axis.
The circuit in Figure 9 reflects the output characteristic, displayed in Fig. 8. It has an output ofEvolts,
when the load current is zero. Hence the model of the circuit can have a voltage source ofEvolts. When
the output terminals are short-circuited, it can be stated that the internal resistance of circuit absorbsE
volts at a current ofIm. This means that the internal resistance of the circuit, called as RTh, has a value of
EoverIm, as shown by the equation displayed in Fig. 9. Hence the circuit model consists of a voltage
source of valueEvolts and a resistorRTh. This resistor is the resistance of the circuit, as viewed from the
load terminals.
Let us see how we can apply what we have learnt. A simple circuit is presented in Fig. 10. The task is to
get an expression for the load currentIL and express it in terms of Thevenins voltage and Thevenins
resistance. Thevenins voltage is the voltage obtained across the load terminals, with the load resistor
removed. In this case, the load resistor is named as R3.
At first, an expression for the load current is obtained without the use of Thevenins theorem. To get the
load current, the steps involved are as follows.
Get an expression for the equivalent resistanceReq, seen by the source, as shown in Fig. 11.
Divide the source voltage by the equivalent resistance to get currentIS supplied by the source. This
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 2/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
3/15
source current flows through resistors,R2 andR3 connected in parallel.
Use the current division rule to get an expression for the load current.
As shown by equation (17), the equivalent resistance is obtained by adding resistorR1 to the parallel value
of resistors,R2 andR3 . The source current is the ratio of source voltage to the equivalent resistance, as
expressed by equation (18).. Then the load current through resistorR3 is obtained using the current
division rule, as shown by equation (19).
Now some mathematical manipulations are required to get Thevenins voltage and Thevenins resistance.
The expression for the load current is expressed by equation (20). Divide both the numerator and the
denominator of equation (20) by the sum of resistors,R1 andR2 , and then we get equation (21). The
numerator of equation (21) is Thevenins voltage. The first part of the denominator, containing resistorsR1 andR2 , is Thevenins resistance. It is the parallel value of resistors R1 andR2 . Once Thevenins
voltage and Thevenins resistance are known, the load current can be obtained as shown by equation (21)
Equation (22) defines the expressions for Thevenins voltage and Thevenins resistance. They are
obtained from equation (21).
From the expression for the load current, we can obtain a circuit and this circuit is presented in Figure 12.
We can now ask what Thevenins voltage and Thevenins resistance represent? How do we obtain them
in a simpler way? They can be obtained as shown next.
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 3/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
4/15
Thevenins voltage is the voltage across the load terminals with the load resistor removed. In other words,
the load resistor is replaced by an open circuit. In this instance, the load resistor isR3 and it is replaced by
an open circuit. Then Thevenin,s voltage is the open circuit voltage, the voltage across resistorR2. This
voltage can easily be obtained by using the voltage division rule. The voltage division rule states the
division of source voltage is proportionate to resistance. Thevenins resistance is the resistance, as viewed
from the load terminals, with both the load resistor and the sources in the circuit removed. Here removal
of the voltage source means that it is replaced by a short circuit, and the load resistor is replaced by an
open circuit. Thevenins resistance is the parallel value of resistors R1 andR2 . Next Thevenins theorem
is presented in a formal manner.
Go To Top of the Page
PRESENTATION OF THEVENINS THEOREM
Thevenins theorem represents a linear network by an equivalent circuit. Let a network with one or more
sources supply power to a load resistor as shown in Fig. 14. Thevenins theorem states that the network
can be replaced by a single equivalent voltage source, marked as Thevenins Voltage or open-circuit
voltage and a resistor marked as Thevenins Resistance. Proof of this theorem is presented below.
Thevenins theorem can be applied to linear networks only. Thevenins voltage is the algebraic sum of
voltages across the load terminals, due to each of the independent sources in the circuit, acting alone. Itcan be seen that Thevenins theorem is an outcome of superposition theorem.
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 4/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
5/15
Thevenins equivalent circuit consists of Thevenins voltage and Thevenins resistance. Thevenins
voltage is also referred to as the open-circuit voltage, meaning that it is obtained across the load terminals
without any load connected to them. The load is replaced by an open-circuit and hence Thevenins
voltage is called as the open-circuit voltage.
Figure 15 shows how Thevenins voltage is to be obtained. Here it is assumed that we have a resistive
circuit with one or more sources. As shown in Fig. 15, Thevenins voltage is the open-circuit voltage
across the load terminals. The voltage obtained across the load terminals without the load being connected
is the open-circuit voltage. This open-circuit voltage can be obtained as the algebraic sum of voltages, due
to each of the independent sources acting alone.Given a circuit, Thevenins voltage can be obtained as
outlined below.
Figure 16 shows how Thevenins resistance is to be obtained. Thevenins resistance is the resistance as
seen from the load terminals. To obtain this resistance, replace each independent ideal voltage source in
the network by a short circuit, and replace each independent ideal current source by an open circuit. If a
source is not ideal, only the ideal part of that source is replaced by either a short circuit or an open circuit
as the case may be. The internal resistance of the source, reflecting the non ideal aspect of the circuit, is
left in the circuit, as it is where it is. A voltage source is connected across the load terminals. Then
Thevenins resistance is the ratio of this source voltage to its current, as marked in Fig. 16. A few
examples are presented after this page to illustrate the use of Thevenins theorem.
Go To Top of the Page
PROOF OF THEVENINS THEOREM
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 5/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
6/15
The circuit in Fig. 17 can be used to prove Thevenins theorem. Equation (1) in the diagaram expresses an
external voltage VY connected to the load terminals, as a function of currentIY and some constants. It is
valid to do so, since we are dealing with a linear circuit. Let us some that the internal independent sources
remain fixed. Then, as the external voltage VY is varied, currentIY will vary, and the variationIY with VY
is accounted for by provision of a coefficient , named as k1 in equation (1). It can be seen that k1 reflects
resistance of the circuit as seen by external voltage source VY. Coefficient k2 reflects the contribution to
terminal voltage by internal sources and components of the circuit. It is valid to do so, since we are
dealing with a linear circuit, and a linear circuit obeys the principle of superposition. Each independentinternal source within the circuit contributes its part to terminal voltage and constant k2 is the algebraic
sum of contributions of internal sources. Adjust external voltage source such that currentIY becomes
zero. As shown by equation (2), the coefficient k2 is Thevenins voltage. To determine Thevenins
resistance, set external source voltage to zero. If the internal sources are such as to yield positive
Thevenins voltage, currentIY will be negative and coefficient k1 is Thevenins resistance, as shown by
equation (3). This concludes the proof of Thevenins theorem.
The step involved in the application of Thevenins theorem are summarized below.
Go To Top of the Page
WORKED EXAMPLE 2
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 6/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
7/15
A problem has been presented now. For the circuit in Fig. 18, you are asked to obtain the load current
using ThevEnins theorem. We have already looked at this circuit, but the purpose here is to show, how
to apply Thevenins theorem.
Solution:
It is a good practice to learn to apply a theorem in a systematic way. The solution is obtained in four
steps. The steps are as shown above.
The first step is to obtain Thevenins voltage as described now. Remove the load resistor, and represent
the circuit, as shown in Fig. 19 in order to get the value of Thevenins voltage, which is the voltage across
resistorR2. This voltage can be obtained is shown next by equation (23).
Equation (23) is obtained using the voltage division rule. The two resistors are connected in series and the
current through them is the same, and hence the voltage division rule can be applied.
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 7/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
8/15
-
8/3/2019 Thevenin's Theorem_ Network Theorems
9/15
WORKED EXAMPLE 3
We take up another example now. Figure 22 contains the circuit. The source voltage is 10 Volts. The
circuit containing the small signal model of a bipolar junction transistor looks similar to this circuit in Fig.
22.
Solution:
You are asked to obtain the Thevenins equivalent of the circuit in Fig. 22. This problem is a bit moredifficult, since it has dependent sources. The Thevenins theorem can be applied to circuits containing
dependent sources also. The only constraint in applying Thevenins theorem to a circuit is that it should
be a linear circuit.
The steps involved are the same, as outlined before for the previous problem. The steps involved are
shown above.:
Given a circuit with dependent sources, it may at times be preferable to obtain the open circuit voltage and
the short circuit current, and then obtain Thevenins resistance as the ratio of open circuit voltage to the
short circuit current. The short circuit current is obtained by replacing the load resistor by a short circuit,
and it is the current that flows through the short circuit. This technique has been used in the proof of
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 9/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
10/15
Thevenins theorem.
Since there is no load connected to the output terminals, voltage V2 is the open circuit voltage, which is
the same as the Thevenins voltage. To obtain the open circuit voltage, the following equations are
obtained.
Equation (26) expresses the voltage across resistorR2. The current through resistorR2 is ten times
currentI, and the value of resistorR2 is 100 . Equation (27) is written for the loop containing the
independent source voltage. The independent source voltage is 10 Volts. The value of resistorR1 is 10
and the current through it can be obtained as shown by equation (27). Equation (28) is obtained by
replacing voltage V2 in equation (27) by its corresponding expression in equation (26).
On simplifying, we can obtain the value of currentI, and the Thevenins voltage, as illustrated by equation
(29).
The second step is to obtain Thevenins resistance. The circuit in Fig. 23 is used for this purpose.
To obtain Thevenins resistance of a circuit with dependent source, it is preferable to obtain the short
circuit current and then obtain Thevenins resistance as the ratio of Thevenins voltage to short circuit
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 10/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
11/15
current. The circuit in Fig. 23 is used to obtain the short circuit current.
Equations (30) to (33) are obtained from the circuit in Fig. 23. When the output terminals are shorted, the
short circuit current, known also as the Nortons current, is ten times current I, as shown by equation (30).
Note that the source voltage is 10 Volts. When the output voltage is zero, current Iis the ratio of source
voltage to resistorR1 and it equals one Ampere, as displayed by equation (31). Equations (32) and (33)
show how Nortons current and Thevenins resistance can be obtained.
Now it is shown how the Thevenins resistancecan be obtained by another way. The circuit in Fig. 24 is
presented for this purpose.
Alternate Method to obtain RTh
Remove the independent voltage source and replace it by a short circuit. Connect a source at the output
as shown in Fig. 24. Then Thevenins resistance is obtained as follows.
Thevenins resistanceis expressed by equation (34). It is obtained with the independent source voltage,
contained in the circuit, being replaced by a short circuit, as shown in Fig. 24.
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 11/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
12/15
Equations (35) to (38) are obtained from the circuit in Fig. 24. Since the source voltage is zero, the sum ofvoltage across resistorR1 and the voltage across the dependent voltage source is zero and we get
equation (35). Equation (36) is obtained by using KVL at node a. The expression obtained for currentIin
equation (35) is used to replace the currentIin equation (36) and this leads to equation (37). On
simplifying, we get equation (38) and the value ofThevenins resistanceis 2 Ohms.
Another View
It is possible to obtain an expression for the currentIx marked in Fig. 24. Equation (39) shows how this
current is obtained. Since we know the voltage across the dependent current source and the current
through it, we can replace it by a resistor, as shown in Fig. 24. The parallel value of two resistors is the
Thevenins resistance.
Equations (40) and (41) illustrate how Thevenins resistance is obtained. Since Thevenins voltage and
Thevenins resistance are known, the equivalent circuit can be drawn.
Go To Top of the Page
WORKED EXAMPLE 4
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 12/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
13/15
Find the current through the load resistorRL.
Solution:
Thevenins theorem is used to get the solution. RemoveRL. Find Thevenins voltage. ReplaceRL by a
short-circuit. Find the current through the short-circuit. Then Thevenins resistance is the ratio of theopen-circuit voltage and the short-circuit current. Then the current through the load resistorRL can be
determined.
First let us obtain Thevenins voltage. The circuit withoutRL is shown below.
Let the resistance of the circuit in Fig. 26, as seen by the source beRA.The value ofRA can be obtained,
as shown by equation (42).
OnceRA is known, the currentIA supplied by the source can be obtained, as shown by equation (43).
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 13/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
14/15
From the circuit in Fig. 26, we can obtain currents I3 andI5, marked in Fig. 26, by using the current
division rule.
Once the values of currentsI3 andI5 are known,Thevenins voltage can be obtained as shown by
equation (46).
To find the short-circuit currentIN , we use the circuit in Fig. 27. Let the resistance of the circuit in Fig.
27, as seen by the source beR
B.The value ofR
B can be obtained, as shown by equation (47).
OnceRB is known, the currentIB supplied by the source can be obtained, as shown by equation (48).
Use the current division rule. Find currents I2 andIc, marked in Fig. 27.
5/13/2011 HEVENIN'S THEOREM: NETWORK TH
netlecturer.com//p03ThevA.htm 14/
-
8/3/2019 Thevenin's Theorem_ Network Theorems
15/15