Therma-TruSlim-Line
Sliding Patio Door
®
™
Assemblyand
Installation
Read all instructions before starting.
Builder or subcontractor, please forward these instructions to the homeowner. Theapplicable standards for these products are governed by the International Residential
Code. Copies of performance ratings and testing are available on our websitewww.thermatru.com and our product manual.
INDEX
DOUBLE PATIO DOOR ASSEMBLY & INSTALLATION...................2
M.E.U. ( Multiple Extender ) ASSEMBLY & INSTALLATION...17
TRANSOM INSTALLATION................................................................24
TRIPLE CONTINUOUS PATIO ASSEMBLY & INSTALLATION.....29
QUAD CONTINUOUS PATIO ASSEMBLY & INSTALLATION.......33
REPAINTING PROCEDURE................................................................38
JAMB EXTENSION INFORMATION
HANDING GUIDE.................................................................................41
SIZING INFORMATION.......................................................................42
Unit
..................................................38
INTERIOR CASING ATTACHMENT...................................................39
TRIPLE SYSTEM INFORMATION.....................................................40
SCREW CHART....................................................................................43
1
The following packages are needed to complete the installation of yourSee page 42 for sizing
information.
Therma-Tru Slim-LineSliding Patio Door System.
®
Check all components for correct size and color.™
Operating
Panel
Operating
Panel
Stationary
Panel
Stationary
Panel
Operating Panel
Stationary Panel
Optional Components
Tools and materials needed for assembly and installation:
TransomCoastal Package
• 100% Silicone Sealant and Caulk Gun• 6' Level• Measuring Tape• Electric Drill• #2 Phillips Drive Bit• Staple Gun or Brad Nails• 1/8 Drill Bit
• Flat-blade Screwdriver
“
• Gloves• Safety Glasses• Partial Roll of Insulation• Shims
Screen
2
Frame Kit
Additional Parts
1-Head Jamb2-Side Jambs1-Sill1-Active Weatherstrip Carrier1-Inactive Weatherstrip Carrier2-Active Panel Hole Plugs1-Panel Bumper12-#10 x 3" Flat Head Screws12-#8 x 3" Pan Head Screws1- This Instruction Booklet2- Panel Anchor Blocks
2- #10 x 1 Phillips Anchor Screws
2- #10 x 2 Phillips Anchor Screws1-Sill Cap Base1-Sill Cap Top1-Drip Cap1-Head Sealing Fin2-Corner Pads
1-Foot Bolt1-Foot Bolt Keeper
1-#8 x 1 S.S. Pan Head Screw3
1-Touch Up Paint
-#8 x 9/16" S.S. Pan Head Screws2-#8 x 1" S.S. Pan Head Screws
½"½"
½"
Handle Set Kit2-Handles1-Mortise Lock1-Keeper1-Spacer1-Escutcheon with Lock1-Escutcheon2-Phillips Screws with Colored Heads4-Hex Drive Screws2-Keys1-Gasket1-Hex Wrench1-Through Pin2-#8 x 1" Flat Head Screws4-#8 x 1" Pan Head Sheet Metal Screws
NOTE:A large work area is needed to assemble the frame kit. Cover area with cardboardfrom one or more door panel cartons to protect frame parts and floor.
1
2
LAY FRAME COMPONENTS ONTO WORK AREA.
ATTACH SILL TO JAMBS
Lay parts on floor and position sill, head and sidejambs with exterior side up.
Apply sealant to sill as shown.
Side Jamb
Sill
Head Jamb
Side Jamb
Fasten side jambs to sill through pre-drilled holesusing (3) #10 x 3 flat head screws. (Starting with
center screw is recommended.)Repeat for opposite side.
“
#10 x 3 Flat Head Screw“
Sill
Side Jamb
NOTE: Be sure that foam pads are in place before assembling frame.
Exterior
3
Frame Assembly
Sealant
Foam Pads
Sealant
3 ATTACH HEAD TO JAMBS
Fasten side jambs to head jamb through pre-drilledholes using (3) #10 x 3 flat head screws. (Starting
with center screw is recommended.)
Repeat for opposite side.
“
#10 x 3 Flat Head Screw“
Head Jamb Side Jamb
4
4 DRIP CAP INSTALLATION
Head Sealing Fin
Aluminum Cap Flashing
Place the aluminum cap flashing on top of the head jamb.Place the head sealing fin on top of the aluminum capflashing. Staple the head sealing fin to each of the anchor
blocks in the head jamb u .
NOTE:If transom is to be mulled to a system, skip step4 and 5.
sing a stapler½"
Exterior
Exterior
Exterior
5
Frame Installation
Check rough opening as follows and correct if necessary:
• Sub-floor to be flat, level, and clean. Sill must be supported throughout itsentire length.
• All four corners to be square. Check with a framing square.• Framing and walls to be plumb. Use a 6-foot level to check both sides of
opening.• All wall surfaces to be straight and sides parallel.
• Opening to be correct size. Allow 3/8 on sides and at head.“ ½"
Wallstraight?
Wallstraight?
Check all fourcorners withsquare.
Check eachside bothways.
Check floorunder sill.
6
4 APPLY SILICONE SEALANT TO BOTTOM OF SILL
Run beads of silicone sealantacross entire length of sillbottom to provide a weather-tight seal.
NOTE:A CONTINUOUS BEAD OF SEALANT IS REQUIRED.
Sealant
5
6
APPLY CORNER PADS TO SEALING FIN
Corner Pad
Apply the corner pads to the sealingfins in the two top corners.
Exterior
7
7
8
SET SYSTEM INTO ROUGH OPENING
Generously apply sealant to the backsideof the sealing fin. From outside of house,set system into rough opening. Applypressure on sill to set sealant.
LEVEL SILL
Sill be flat and level. Check and make anynecessary adjustments.
If necessary, add temporary blocking underprojecting exterior edge of sill to serve assupport during construction.
MUST
Sealant
Exterior
8
10
PLUMB SIDE JAMBS
Interior
Shims
Jambs must be plumb and straight.Shim as necessary to remove any bow.
9
Fasten system to rough opening using staples,nails, or screws through sealing fin at the corners.Fasten through every third opening in the sealingfin. If needed the jambs can be back filled with insulation.
INSTALL SILL CAP BASE
Install the vinyl sill cap base by starting at each jamb and working towardsthe center of the door. Use a rubber mallet to snap into place.
Exterior
Shims
Vinyl Sill Cap Base
9
12 INSTALL STATIONARY PANEL
A. Apply a 1/4 bead of caulk (recommend clear sealant) to
bottom of sill inactive door riser.B. From exterior side of system, install stationary panel by inserting
top of panel into exterior channel. Rotate bottom panel inuntil sill inactive door riser leg sets into groove. As reference theinterior side of the slab is always the side with the glazing bead.
C. Slide slab tightly against side jambD. Wipe off excess caulking.
”
A
11 SECURE FRAME IN ROUGH OPENING
Using (12) #10 x 3 pan head screws, fasten frame to rough
opening through pre-drilled holes in frame. The sill doesnot have pre-drilled holes.
“
#10 x 3 Pan Head Screws“
#10 x 3“ Pan Head Screws
The screws used on the sill are installed through thesill cap into the sill substrate. There is a v-groovein the sill cap to assist in aligning the screw.
The sill's center screw needsto be installed three inchesoff center in the direction ofthe active panel.
Sill Cap
Sill
Exterior
Exterior
Glazing Bead
Riser
Exterior
Interlock
10
13
15A. Locate the two weatherstrip carriers in the frame box, one for the active panel and one for the
fixed panel.B. The carriers have been sent along for cutting in the field based on the handing of the door.C. Follow the instructions below for the door handing you are installing.
Cut off this end in field for left hand (LF) door
Cut off this end in field for right hand (FR) door
Cut off this end in field for right hand (FR) door
Cut off this end in fieldfor left hand (LF) door
Active PanelFixed Panel
CUTTING WEATHERSTRIP CARRIERS
INSTALL ANCHOR TO THE INACTIVE PANEL & SILL
Remove the bottom screw on the inactive paneland discard. Insert the panel anchor as shown.U
ttach the anchor to
the panel with the #10 x 1 phillips pan head screw(2) that is supplied.
sing a 1/8" drill bit drill into the toe-screw openingthrough the fiberglass and substrate. Install the
#10 x 2 phillips pan head screw (1) into the panelanchor through the toe-screw hole. A
½"
½"
1
2
14
Remove the top screw in the inactivepanel and discard the screw. Then insertthe panel anchor as shown.
attach the anchor
to the panel with the #10 x 1 phillipspan head screw (2) that is supplied.
Using a 1/8"drill bit, drill into the toe-screw openingthrough the fiberglass and substrate.
Install the #10 x 2 phillips pan headscrew (1) into the panel anchor throughthe toe-screw hole.Then
½"
½"
2
1
INSTALL ANCHOR TO THE INACTIVE PANEL & HEAD
Panel Anchor
Panel Anchor
11
17
18
INSTALL ACTIVE PANEL
InteriorFrom interior side of system, install activepanel up into interior channel in headjamb. Push upwards as far as possibleand rotate into place until rollers engageonto sill roller track.
NOTE: BE SURE TO HAVE THE ACTIVE PANEL NEARTHE CLOSED POSITION BEFORE INSTALLING TOENSURE THAT THE INTERLOCKS WILL MEET WHENTHE DOOR IS CLOSED. BE SURE THAT THE PANEL ISSQUARE TO THE FRAME.
ADJUST ROLLERS
Using a screw driver, turnadjustment screws in rollersleft or right until panel islevel and glides smoothlyacross the track.
Close panel to within 1/4
of lock jamb. Use visualmargin to assure panel isadjusted straight withframe.
“
Active Panel Installation
16 ATTACH INACTIVE WEATHERSTRIP CARRIER
ExteriorInactiveWeatherstripCarrier
Install weatherstrip carrier, use a block of wood orrubber mallet to avoid damage to the parts. Line upthe fixed slab weatherstrip carrier flush to the bottomof the head jamb. Insert barbs into stile grooves, tap intoplace, then do the same at the sill. Work your waytowards the center of the panel. Make sure that bothcarriers fit properly into the slots on the edge ofeach slab.
Interior
12
19
Handle Installation
20
ATTACH ACTIVE WEATHERSTRIP CARRIER
Align active weatherstrip carrier with bottom edge of activepanel. Starting at bottom, insert barbs into stile grooves.Working your way up, tap in place with a hammer andwood block or rubber mallet. Carefully inspect interioredge of interlock. Tap as necessary to obtain a tight fitalong door edge.
Interior
21
INSERT PANEL BUMPER
Insert panel bumper into innermost channelin head jamb, butting end of bumper againststationary side jamb. Seat panel bumper flushwith head jamb.
InteriorSide
PanelBumper
Head Jamb
Side Jamb
NOTE: IF NEEDED THE BUMPER CAN BE CUT DOWN FROM ITSORIGINAL LENGTH OF SIX INCHES TO FOUR AND A HALF INCHES.THIS WILL ALLOW FOR A WIDER ENTRANCE.
INSTALL MORTISE LOCK
Install mortise lock and spacerthrough pre-fabricated holes inactive door edge.
Spacer
(2) 1" Phillips FlatheadMachine Screws
Exterior
13
22 ALIGN EXTERIOR HANDLE
A. Assemble handle to escutcheon plate, according to the hand of the door, with two hex screws.The curve of the handle should slope toward the center of the door slab that it is being installedon. Tighten securely to prevent loosening during operation.
B. The black foam gasket should be installed under the exterior escutcheon plate. This piece willprevent water infiltration.
C. Insert through pin into escutcheon plate.D. The tailpiece will require positioning prior to assembly on the door. Rotate the tailpiece until it
reaches a horizontal position.E. Place exterior handle on door aligning holes in panel.
Through Pin
Exterior
Tailpiece
Key Cylinder
A. Assemble handle to escutcheon plate, according to the hand of the door, with two hex screws.The curve of the handle should slope toward the center of the door. Tighten securely to preventloosening during operation.
B. If desired, the thumb knob can be changed to different positions when in the locked and unlockedpositions. To do this, remove the screw in the stem of the thumb turn. Next, rotate the adaptor sothe desired threaded hole in the adaptor lines up with a hole in the thumb turn stem.
C. Turn the thumb knob to align it with the tailpiece
phillips pan head
. Placeinterior handle over latch, aligning holes in panel.
D. Fasten handles together with (2) colored screws,do not tighten the mounting screws completely.
E. Completely close the active door, rotate the key to the locked andunlocked positions. In each case the key should be removable.This indicates that the key is installed properly. If it does notoperate properly rotate the tailpiece in the opposite directionand reinstall. Tighten the mounting screws to complete theinstallation.
(2) 2" Phillips Pan Head Colored Screws
NOTE:USE CAUTION NOT TO OVERTIGHTEN SCREWS.
ALIGN INTERIOR HANDLE23
Escutcheon
Handle
Gasket
Thumb Knob
14
24
25
INSTALL KEEPER
INSTALL FOOT BOLT
(1) #8 x 1 S.S. Pan Head Sheet Metal Screws½"
(3) #8 x 9/16" S.S. Pan Head Sheet Metal Screws
Align keeper to pre-drilled holesin active jamb and fasten with
(4) 1 phillips pan head screws.
Close door and adjust keeper forproper latch engagement. Latchthrow can be adjusted by theslotted adjustment screw on theface of mortise lock.
½"
(4) 1 Phillips PanHead Screws
½"
Align foot bolt to pre-drilled holesin active slab and fasten with the screws shown below.
Foot Bolt
15
26
27
INSTALL SILL CAP TOP
INSTALL FOOT BOLT KEEPER
Place a continuous bead of clear sealant at thelocations shown across the base profile. Installthe sill cap top by starting at each jamband working towards the center of the door. Usea rubber mallet to snap into place. Seal the endsof both profiles to the side frame as shown.Clean up any excess sealant.
#8 x 1" S.S. Pan Head Sheet Metal Screw
Close the active door completely, align keeper with footbolt. Slide the keeper as far as it will go towards the exteriorof the unit. Only the two exposed holes will be used forinstallation. Use a 1/8" drill bit to drill two holes through theholes in the keeper into the sill cap and through the fiberglassof the sill. Fill the holes with a small amount of clear sealant.Screw the two #8 x 1" S.S. pan head sheet metalscrews into the holes. Clean up any excess sealant.
End of RiserSealed to Frame
Sill Cap Top
ContinuousSealant
Exterior
Exterior
Exposed holes
16
29 XINSERT PLUGS
Weatherproof, Finish and Maintain System
• Caulk around entire system on exterior side. Seal sealing fins to siding or facing,seal front bottom edge of sill, seal all joints between jambs and moldings.
• Seal joints between exterior hardware trim and door face to prevent air andwater infiltration.
• Remove sill tape and the labels on the glass.
• Use the touch up paint to paint the heads of the rough opening screws.
Refer to the instruction label on the screen.
28 SLIDING SCREEN DOOR
Final Assembly
are supplied, insert the plugsinto roller adjustment holesTwo plugs
.
Hole plug
Exterior
17
M.E.U. Assembly
Frame Kit
Stationary Panel
1-Head Jamb2-Side Jambs1-Sill2 -Mullion Strips12 -#10 x 3" Flat Head Screws12 -#8 x 3" Pan Head Screws6 -#8 x 2" Pan Head Screws1-Sill Cap Base1-Sill Cap Top1-Drip Cap1-Head Sealing Fin2-Corner Pads1-Splice2-Panel Anchors
2 -#10 x 1 Pan Head Screws1-This Instruction Booklet1 -Touch Up Paint
½"
Tools and materials needed for assembly and installation:• 100% Silicone Sealant and Caulk Gun
• Electric Drill• #2 Phillips Drive Bit• Staple Gun or Brad Nails• 1/8 Drill Bit
• 2 x 4 Wood Blocks• Gloves
“
• 6' Level• Measuring Tape
• Flat-blade Screwdriver
• Safety Glasses• Partial Roll of Insulation• Shims
The following packages are needed to complete the installation of your
See page 42 for sizing information.
Therma-Tru Slim-LineSliding Patio Door Multiple Extension System.
®
Check all components for correct size and color.™
18
NOTE:A large work area is needed to assemble the frame kit. Cover area with cardboardfrom one or more door panel cartons to protect frame parts and floor.
1A
2A
Assembly
LAY PANEL ON 2 X 4 BLOCKS
Position 2 x 4 blocks on edge.
Lay panel on top of blocks withexterior side up. As reference theinterior of the slab is always theside with the glazing bead.
2 x 4 Block
CAUTION:Skin of panel to be laying on 2 x 4 blocks,not glass. Blocks not to extend beyond panel edges.
INSTALL PANEL ANCHORS
#10 x 1 Pan Head Screw½"
Remove the top screw in the slab side anddiscard the screw. Insert panel anchor as
shown and attach with #10 x 1phillips pan head screw that is supplied.
Repeat on opposite panel side.
½"
Panel Top
Panel Side
Top Screw
Glazing BeadExterior
19
4A PLACE SIDE JAMB
Position both side jambs up against panel edges.
3A LAY FRAME COMPONENTS AROUND PANEL
Place frame components, withexterior side up, around panel.
Side Jamb
Head Jamb
Side Jamb
Sill
Exterior
Temper Blaze
Top
Bottom
Exterior
20
6A PLACE SILL
APPLY SEALANT TO SILL5A
Sealant
Apply a continuous bead of sealant on riser and both ends of sill.
Position sill riser under door panel.
Sealant
Sill
Side Jamb
187A ATTACH SILL TO JAMB
#10 x 3 Flat
Head Screws
“
Fasten side jambs to sill through pre-drilled holesusing (3) #10 x 3 flat head screws. (Starting with
center screw is recommended.)
Repeat for opposite side.
“
Panel
Riser
Exterior
Exterior
Exterior
21
8A ATTACH HEAD JAMB
Fasten side jambs to head jamb throughpre-drilled holes using (3) #10 x 3 flat
head screws. (Starting with center screwis recommended.)
Repeat for opposite side.
“ #10 x 3
Flat HeadScrews
“
Slide head jamb onto edge of panel.
Align with side jambs.
9A MULLED OR FRAMED INDEPENDENT
If framing system independently go to page 4 steps 4 - 10, then secure inrough opening as shown below. Install sill cap top per installations instep 26, page 15.
If mulling to another system remove the sealingfin from the mating edge. Proceed to step 10A.
Sill Cap
Sill
#10 x 3 Pan Head Screw“
Exterior
Exterior
#10 x 3
pan headscrews
“
22
11A INSTALL SYSTEM
#10 x 3 Pan Head Screw“
Turn to page four and follow steps 4 -29. Note thatsome of the details in step 4 - 29 are tailored to the doublepatio systems and some details may vary slightly. The attachmentpoints for the mulled triple are shown below.
#10 x 3 pan head screws“
The sill's center screw needs to be installed three inchesoff center in the direction of the active panel.
10A ATTACH M.E.U. TO TWO PANEL SYSTEM
(3) #8 x 2
pan head screws
“
Run a bead of sealant on the mullion covers and then staple thecovers to the transom. Staple into the substrate and not thefiberglass. A 3/4" staple is recommended. Staple the twomullion covers to the M.E.U. Align M.E.U. With two-panelsystem. Using (6) #8 x 2 pan head screws, fasten M.E.U. and
two-panel systems together through pre-drilled holes in frames.If the drip cap is being used on this installation use thealuminum splice to cover the gap between the drip cap ofthe M.E.U., and the drip cap of the two-panel system.
“
(3) #10 x 2
pan head screws
“
Mullion Cover
Mullion Cover
Aluminum Splice
Sealant
23
Weatherproof, Finish and Maintain System
• Caulk around entire system on exterior side. Seal sealing fins to siding or facing, seal frontbottom edge of sill, seal all joints between jambs and moldings.
• Seal joints between exterior hardware trim and door face to prevent air and water infiltration.
• Paint or stain according to Therma-Tru instructions. Do NOT paint gaskets or weatherstrip.
• Maintain or replace sealants and finishes as soon as any deterioration is evident. For semi-gloss, glossy paints, or clear coats, do this when surface becomes dull or rough. More severeexposures require more frequent maintenance.
®
• Use the touch up paint to paint the heads of the rough opening screws.
24
24
Transom
Transom
Tools and materials needed for assembly and installation:• 100% Silicone Sealant and Caulk Gun• 1' Level• Measuring Tape• Electric Drill• #2 Phillips Drive Bit• Staple Gun or Brad Nails• 1/8 Drill Bit
• Flat-blade Screwdriver
“
• Gloves• Safety Glasses• Partial Roll of Insulation• Shims• Saw
The following packages are needed to complete the installation of yourSee page 42 for
sizing information.
Therma-Tru Slim-LineSliding Patio Door Transom.
®
Check all components for correct size and color.™
1B
APPLY CORNER PADS TO SEALING FIN
Corner Pad
Apply the corner pads to the sealingfins in the two top corners.
2B
MULLED OR FRAMED INDEPENDENT
If mulling to a system remove the sealing fin from the matingedge. Complete step 4 on page 4. Proceed to step 2B.
If framing independent proceed to step 6B. If you are framing twotransoms together independently proceed to step 3B followed by step 6B.
FRAMED INDEPENDENT- Run a bead of sealant on backside of mullion covers.- Staple covers to transom through anchor blocks not fiberglass frame using 3/4" staples.
MULLED ON PATIO DOOR- Trim ½" off one end of mullion cover.- Run a bead of sealant on backside of mullion cover.
- Staple cover to transom throughanchor blocks, not fiberglass.
Transom
Center Mull Strip
Transom
Patio System Head Jamb
3B APPLY MULLION COVER FOR DOUBLE TRANSOMS
25Center Mull Strip
Sealant
26
5B MODIFYING CORNER PADS FOR MULLED TRANSOMS
To maintain a consistent seal around the system the corner padsneed to be applied. Cut pad as shown and apply to sealing finjoint.
Cut Line
4B ATTACH TRANSOM TO PATIO UNIT
A. Run a bead of sealant on the mullion covers and then staple thecovers to the transom. Staple into the substrate and not the fiberglass.A 3/4" staple is recommended.
B. Align transom to patio door system. Using (6) #8 x 2 pan head screws,
fasten transom and patio door system together through pre-drilled holes in frames.Number of screws will vary based on the system width.
“
(6) #8 x 2
pan head screws
“
Mullion Cover
Mullion Cover
Exterior
Sealant
27
5B INSTALL SYSTEM
Turn to page 5 and follow steps 6 -10. Secure frame in rough opening using the #10 x 3" panhead screws. Fasten frame to rough opening through pre-drilled holes in the frame. Follow thescrew spacing shown below for the sill screw location. Fasten sill to floor. Turn to page 9 andfollow steps 12 - 29. Note that some of the details are tailored to the double patio systems andsome details may vary slightly.
The sill's center screw needsto be installed three inchesoff center in the direction ofthe active panel.
The sill's center screw needsto be installed three inchesoff center in the direction ofthe active panel.
MEU DOUBLE
TRIPLE MULLED TRIPLE CONTINUOUS
QUAD CONTINUOUS The screws used on the sill are installed through thesill cap into the sill substrate. There is a v-groovein the sill cap to assist in aligning the screw.
Sill Cap
Sill
If this is the active door side thisscrew needs to be installed threeinches off center in the direction ofthe active panel.
Exterior
28
6B INDEPENDENT INSTALLATION
Turn to page 5 and follow steps 4 - 9. Secure frame in rough openingusing the #10 x 3" pan head screws. Fasten frame to rough openingthrough pre-drilled holes in the frame.
Exterior
29
Continuous Triple Assembly
Operating
Panel
Operating
PanelStationary
Panel
Stationary
Panel
1
2
TransomCoastal Package
• 100% Silicone Sealant and Caulk Gun• 6' Level• Measuring Tape• Electric Drill• #2 Phillips Drive Bit• Staple Gun or Brad Nails• 1/8 Drill Bit
• Flat-blade Screwdriver
- Panel
- Stationary Panel
Optional Components
Tools and materials needed for assembly and installation:
“
Operating
• Gloves• Safety Glasses• Partial Roll of Insulation• Shims
Frame Kit1-Head Jamb2-Side Jambs1-Sill1-Active Weatherstrip Carrier1-Inactive Weatherstrip Carrier2-Active Panel Hole Plugs1-Panel Bumper12-#10 x 3" Flat Head Screws12-#8 x 3" Pan Head Screws1- This Instruction Booklet4- Panel Anchor Blocks4- #10 x 1 Phillips Anchor Screws4- #10 x 2 Phillips Anchor Screws1-Sill Cap Base1-Sill Cap Top1-Drip Cap1-Head Sealing Fin2-Corner Pads1-Astragal
½"½"
Handle Set Kit2-Handles1-Spacer1-Mortise Lock1-Keeper1-Escutcheon with Lock1-Escutcheon2-Phillips Screws with Colored Heads4-Hex Drive Screws2-Keys1-Gasket1-Hex Wrench1-Through Pin2-#8 x 1" Flat Head Screws4-#8 x 1" Pan Head Sheet Metal Screws
Stationary
Panel
Stationary
Panel
Additional Parts1-Foot Bolt1-Foot Bolt Keeper1-#8 x 1 S.S. Pan Head Screw3-#8 x 9/16" S.S. Pan Head Screws2-#8 x 1" S.S. Pan Head Screws1-Touch Up Paint
½"
Screen
The following packages are needed to complete the installation of your
See page 42 for sizing information.
Therma-Tru Slim-LineSliding Patio Door Continuous Triple Assembly.
®
Check all components for correct size and color.™
30
1C FRAME ASSEMBLY
3C INSTALL ASTRAGAL
2C INSTALL THE FIRST STATIONARY PANEL
A. Apply a 1/4 bead of caulk (recommend clear sealant) to bottom
of sill inactive door riser. Where inactive panel is to be installed.B. Locate the non-handed stationary slab, this slab has no interlocks
as shown below. From exterior side of system, install stationarypanel by inserting top of panel into exterior channel. Rotatebottom panel in until sill inactive door riser leg sets in groove.
C. Slide slab tightly against side jambD. Wipe off excess caulking.E. Proceed to page 10 and follow steps 13 and 14.
”
Proceed to page 3 and follow steps 1 - 11. Note thatsome of the details in step 1 - 11 are tailored to the doublepatio systems and some details may vary slightly. Secure theframe in the rough opening at the attachment points shown.
A
Install astragal, using a block of wood or rubber malletto avoid damage to the parts. Line up astragal to thebottom of the slab. Insert barbs into stile grooves. Tap intoplace, repeat at head. Work your way towards the center ofthe panel. Check fit of astragal along entire length of panel.
Glazing BeadExterior
Exterior
Exterior
31
4C INSTALL SECOND PANEL
5C PANEL INSTALLATION CONTINUED
A. Apply a 1/4 bead of caulk (recommend clear sealant) to
bottom of sill inactive door riser.B. From exterior side of system, install stationary panel by inserting
top of panel into exterior channel. Rotate bottom panel inuntil sill inactive door riser leg sets into groove. The interlockshould be towards the active door.
C. Slide slab tightly into the astragal.D. Wipe off excess caulking.
”
A
B
C
Follow steps 13 - 19 to complete panel installation.
6C HANDLE AND MORTISE LOCK INSTALLATION
Follow steps 21 - 29 to complete the handle and mortise lock installation.
Riser
Interlock
Exterior
Exterior
32
Weatherproof, Finish, and Maintain System
• Caulk around entire system on exterior side. Seal sealing fins to siding or facing,seal front bottom edge of sill, seal all joints between jambs and moldings.
• Seal joints between exterior hardware trim and door face to prevent air andwater infiltration.
• Remove sill tape and the labels on the glass.
• Use the touch up paint to paint the heads of the rough opening screws.
3"
7C INSERT PANEL BUMPER
Insert panel bumper into innermost channelin head jamb. Bumper location should allowfor the maximum door opening but stop thedoor panel before the handle could pinch apersons fingers. Three inches is recommendedas the minimum clearance.
InteriorSide
PanelBumper
Head Jamb
PanelBumper
33
Continuous Quad Assembly
Operating
Panel
Operating
Panel
Stationary
Panel
Stationary
Panel
2 - Operating Panels
2 - Stationary Panels
Optional Components
Tools and materials needed for assembly and installation:
TransomCoastal Package
• 100% Silicone Sealant and Caulk Gun• 6' Level• Measuring Tape• Electric Drill• #2 Phillips Drive Bit• Staple Gun or Brad Nails• 1/8 Drill Bit
3 32
• Flat-blade Screwdriver
“
• / Drill Bit
• Gloves• Safety Glasses• Partial Roll of Insulation• Shims
“
Frame Kit1-Head Jamb2-Side Jambs1-Sill2-Active Weatherstrip Carriers2-Inactive Weatherstrip Carriers4-Active Panel Hole Plugs2-Panel Bumpers24-#10 x 3" Flat Head Screws24-#8 x 3" Pan Head Screws1- This Instruction Booklet4- Panel Anchor Blocks4- #10 x 1 Phillips Anchor Screws4- #10 x 2 Phillips Anchor Screws1-Sill Cap Base1-Sill Cap Top1-Drip Cap1-Head Sealing Fin2-Corner Pads1-Astragal1-Keeper1-Strike Spacer1-Strike Backer4-#10-32 x 1 1/4" PPH SS MS
½"½"
Handle Set Kit4-Handles1-Mortise Lock1-Spacer1-Keeper1-Escutcheon with Lock3-Escutcheons4-Phillips Screws with Colored Heads8-Hex Drive Screws2-Keys2-Gaskets2-Hex Wrenches2-Through Pins4-#8 x 1" Flat Head Screws8-#8 x 1" Pan Head Sheet Metal Screws
Stationary
Panel
Stationary
Panel
Operating
Panel
Operating
Panel
Additional Parts2-Foot Bolts2-Foot Bolt Keepers2-#8 x 1 S.S. Pan Head Screws6-#8 x 9/16" S.S. Pan Head Screws4-#8 x 1" S.S. Pan Head Screws1-Touch Up Paint1-Screen Astragal4-#6 x 3/4" TEK Screws
½"
2 - Screens
The following packages are needed to complete the installation of your
See page 42 for sizing information.
Therma-Tru Slim-LineSliding Patio Door Continuous Quad Assembly.
®
Check all components for correct size and color.™
34
1D FRAME ASSEMBLY STEPS 1 -11
3D
2D INSTALL THE FIRST STATIONARY PANEL
A. Apply a 1/4 bead of caulk (recommend clear sealant) to
bottom of sill inactive door riser.B. From exterior side of system, install stationary panel by inserting
top of panel into exterior channel. Rotate bottom panel inuntil sill inactive door riser leg sets into groove.
C. Slide slab tightly against side jambD. Wipe off excess caulking.E. Repeat for opposite side.
”
As referencethe interior of the slab is always the side with the glazing bead.The interlock should be towards the center of the door.
AB
PANEL INSTALLATION CONTINUED
Follow steps 13 - 19 to complete the panel installation.Most of these steps will need to be completed twice.
If this is the active door side thisscrew needs to be installed threeinches off center in the direction ofthe active panel.
Proceed to page 3 and follow steps 1 - 11. Note thatsome of the details in step 1 - 11 are tailored to the doublepatio systems and some details may very slightly. Secure theframe in the rough opening at the attachmentpoints shown below.
Glazing BeadExterior
Interlock
Riser
Exterior
Exterior
35
4D
6D
5D INSERT PANEL BUMPER
Insert panel bumper into innermost channelin head jamb, butting end of bumper againststationary side jamb. Seat panel bumper flushwith head jamb.
InteriorSide
PanelBumper
Head Jamb
Side Jamb
NOTE: IF NEEDED THE BUMPER CAN BE CUT DOWN FROM ITSORIGINAL LENGTH OF SIX INCHES TO FOUR AND A HALF INCHES.THIS WILL ALLOW FOR A WIDER ENTRANCE.
PanelBumper
INSTALL ASTRAGAL & KEEPER
Follow steps 21 - 23 then 25 - 27 to complete the handle and mortise lock installation.
HANDLE AND MORTISE LOCK INSTALLATION
Astragal
Keeper
#10-32 x 1 1/4" PPH SS MS
Nylon Strike Spacer
SS Strike Backer
Assemble the parts shown below to the astragal with 4 #10 - 32 x 1 1/4" PPH SS MS. Install the topand bottom of the astragal and work towards the center. Note the notched portion goes at the bottomof the slab. Take caution to align the astragal with the bottom of the panel.
36
7D PASSIVE HANDLE INSTALL
A. Assemble handle to escutcheon plate according to the hand of the door, with two hex screws.The curve of the handle should slope toward the center of the slab it is being installed into.Tighten securely to prevent loosening during operation.
B. The black foam gasket should be installed under the exterior escutcheon plate. This piece willprevent water infiltration.
C. Insert through pin into escutcheon plate.D. Place exterior handle on door aligning holes in panel.
Exterior
A. Assemble handle to escutcheon plate according to the hand of the door, with two hex screws.The curve of the handle should slope toward the center of the door. Tighten securely to preventloosening during operation.
B. If desired, the thumb knob can be changed to different positions when in the locked and unlockedpositions. To do this, remove the screw in the stem of the thumb turn. Next, rotate the adaptor sothe desired threaded hole in the adaptor lines up with a hole in the thumb turn stem.
C.hillips pan head
Place interior handle over latch aligning holes in panel.D. Fasten handles together with (2) p colored screws.
Tighten the mounting screws to complete the installation.
(2) 2" Phillips Pan Head Colored Screws
NOTE:USE CAUTION NOT TO OVERTIGHTEN SCREWS.
ALIGN INTERIOR HANDLE8D
Escutcheon
Handle
Gasket
37
9D INSTALL SCREEN ASTRAGAL
Weatherproof, Finish, and Maintain System
• Caulk around entire system on exterior side. Seal sealing fins to siding or facing,seal front bottom edge of sill, seal all joints between jambs and moldings.
• Seal joints between exterior hardware trim and door face to prevent air andwater infiltration.
• Remove sill tape and the labels on the glass.
• Use the touch up paint to paint the heads of the rough opening screws.
10D SCREEN INSTALLATION
Follow steps 28 - 29 to complete the installation. Do not use the screws that are suppledwith the screen. Use two #6 x 3/4" TEK screws instead.
ScreenAstragal
Insert the screen astragal on the passivescreen. Using a 3/32" drill bit drill a holethrough the astragal six inches down fromthe top and another one six inches from thebottom. Then screw two of #6 x 3/4" TEKscrews into the screen threw the holes inthe astragal.
38
4 9/16"4 9/16"
6 9/16"6 9/16"
2 x 4 CONSTRUCTION2 x 4 CONSTRUCTION
2 x 6 CONSTRUCTION2 x 6 CONSTRUCTION
2 "2 "
3/4"3/4"
1 1/8"1 1/8"1 1/8"1 1/8"
B REPAINTING PROCEDURE
1. Sand the surface to be recoated with 180 grit sandpaper to abrade and make porous.2. Remove all sanding dust from the surface. This can be accomplished by using a damp cloth.3. Optional: Wipe the surface with a solvent paint degosser applied with a clean cloth followed
by a final wipe with an additional clean cloth to ensure the surface is free of any contaminates.4. Apply Sherwin Williams DTM Bonding Primer part # B66A50 to the surface and let the
coating dry, following the directions provided on the label located on the back of the can.5. Topcoat the Sherwin Williams DTM Bonding Primer with a high quality acrylic latex
coating such as Sherwin Williams SuperPaint A84 Series or Sherwin Williams DTMAcrylic Coating B66 Series.
For store locations of the above mentioned paints call 1-800-4SHERWIN
Corresponding
A89T54 A89W507 A89W53 A89W51
Sherwin Williams SuperPaint Codes:
BRONZE WHITE STONE ALMOND
N1 10/32 R2 1/128 B1 9/32 B1 4/32 +1/64R2 13/32 B1 1/64 W1 10/32 Y3 19/32W1 39/32 N1 1/64 N1 2Y +46/32 N1 2Y +18/32B1 6Y +62/32
TM
TM
TM TM
TM
A JAMB EXTENSION INFORMATION
Additional Information
The following images are intended tohelp clarify how a Slim-Line patio dooris installed in different frame openings.The jamb extensions are made of standardwood trim materials, readily available fromlumber yards and building material retailstores. Attach the jamb extensions throughthe side into the wall.
Exterior Exterior
39
C INTERIOR CASING ATTACHMENT
Interior casing may be attached to the Slim-Line frame in either of the following ways.
An air nailer can be used to fasten the interior casing to the Slim-Line frame using 0.050” x1- wire brad nails through the casing and fiberglass frame. For maximum holding power,ensure that nails are installed through anchor blocks located within frame profiles. Locationsare shown below for standard two-panel systems.
For manual application, we suggest using 4d-1- finish nails. They can be used to secure interiorcasing to the frame. Pre-drilled pilot holes (1/16 dia.) are recommended to avoid splitting casing orframe. Ensure that nails are installed through anchor blocks for maximum holding power.
½"
½""
LockCenterLine
SystemCenterLine
5"
5"
5"
6 1/4"5"
5"
5"
1"
6 1/4"
5"
40
The intention of this section is to clarify the differences between a triple mulled andtriple continuous Slim-Line Patio Door System.
Handing Configurations for a Mulled Triple:
LFF* (Left Hand Active, Fixed, Fixed)FFR* (Fixed, Fixed, Right Hand Active)
When ordering a LFF or FFR patio door the continuous configuration will be used as theautomatic default. If a LFF or FFR is needed in a mulled configuration it can be ordered asa double and a multiple extension system and then joined in the field.
Please note that the overall width of a mulled system is different then that of a continuous system.Another significant difference between a mulled triple and a continuous triple is the packaging.A triple continuous system will be shipped in two uni-boxes and a long frame box.In comparison, a mulled system will ship in just two boxes.
FLF (Fixed, Left Hand Active, Fixed)FRF (Fixed, Right Hand Active, Fixed)
Handing Configurations for a Continuous Triple:
LFF (Left Hand Active, Fixed, Fixed)FFR (Fixed, Fixed, Right Hand Active)
*
TRIPLE CONTINUOUS PATIO DOORLFF SHOWN
TRIPLE MULLED PATIO DOORFRF SHOWN
D TRIPLE SYSTEM INFORMATION
41
All quad systems are left handed.
LEFT HAND DOOR (LF) RIGHT HAND DOOR (FR)
NOTE: DOORS ARE HANDED AS VIEWED FROM THE EXTERIOR.
LEFT HAND DOOR (LFF)
E DOOR HANDING GUIDE
42
R.H. = Replacement HeightSL = Side LiteX = Active DoorO = Inactive DoorT = TripleQ = Quad
SIZING INFORMATION
DESCRIPTION CONFIGURATION REF SYSTEM WIDTH # PER. CONFIG.
WIDTH HEIGHT WIDTH HEIGHT WIDTH HEIGHT
2/6 FIXED SL 32 9/16 1 32 9/16 16 33 5/16 16 1/2 24 7/16 8 3/8
3/0 FIXED SL 38 9/16 1 38 9/16 16 39 5/16 16 1/2 30 7/16 8 3/8
4/0 FIXED SL 50 9/16 1 50 9/16 16 51 5/16 16 1/2 42 7/16 8 3/8
5/0 XO or OX 59 1/4 1 59 1/4 16 60 16 1/2 51 1/8 8 3/8
6/0 XO or OX 71 1/4 1 71 1/4 16 72 16 1/2 63 1/8 8 3/8
8/0 XO or OX 95 1/4 1 95 1/4 16 96 16 1/2 87 1/8 8 3/8
9/0 XOO or OOX 106 13/16 1 106 13/16 16 107 9/16 16 1/2 98 11/16 8 3/8
9/0 OXO 109 7/8 1 109 7/8 16 110 5/8 16 1/2 101 3/4 8 3/8
10/0 OXXO 115 3/4 2 57 13/16 16 116 1/2 16 1/2 49 11/16 8 3/8
12/0 XOO or OOX 142 13/16 2 71 11/32 16 143 9/16 16 1/2 63 7/32 8 3/8
12/0 OXO 145 7/8 2 72 7/8 16 146 5/8 16 1/2 64 3/4 8 3/8
12/0 OXXO 139 3/4 2 69 13/16 16 140 1/2 16 1/2 61 11/16 8 3/8
PATIO TRANSOM SIZING SPECIFICATIONS
SYSTEM DIM. ROUGH OPENING DAYLIGHT SIZE
DESCRIPTION WIDTH HEIGHT
2/6 X R.H. 29.500 76.188 24.188 70.750
3/0 X R.H. 35.500 76.188 30.188 70.750
4/0 X R.H. 47.500 76.188 42.188 70.750
2/6 X 8/0 R.H. 29.500 92.188 24.188 86.750
3/0 X 8/0 R.H. 35.500 92.188 30.188 86.750
4/0 X 8/0 R.H. 47.500 92.188 42.188 86.750
DAYLIGHT SIZE
PATIO SYSTEM INFORMATION
DESCRIPTION CONFIGURATION GRIDS
WIDTH HEIGHT WIDTH HEIGHT # OF LITES
2/6 X R.H. FIXED SL 32 9/16 79 1/2 33 5/16 80 10 or 15
3/0 X R.H. FIXED SL 38 9/16 79 1/2 39 5/16 80 10 or 15
4/0 X R.H. FIXED SL 50 9/16 79 1/2 51 5/16 80 20
2/6 X 8/0 R.H. FIXED SL 32 9/16 95 1/2 33 5/16 96 12 or 18
3/0 X 8/0 R.H. FIXED SL 38 9/16 95 1/2 39 5/16 96 12 or 18
4/0 X 8/0 R.H. FIXED SL 50 9/16 95 1/2 51 5/16 96 24
5/0 X R.H. XO or OX 59 1/4 79 1/2 60 80 10 or 15
6/0 X R.H. XO or OX 71 1/4 79 1/2 72 80 10 or 15
8/0 X R.H. XO or OX 95 1/4 79 1/2 96 80 20
9/0 X R.H. XOO or OOX 106 13/16 79 1/2 107 9/16 80 10 or 15
9/0 X R.H. OXO 109 7/8 79 1/2 110 5/8 80 10 or 15
10/0Q X R.H. OXXO 115 3/4 79 1/2 116 1/2 80 10 or 15
12/0T X R.H. XOO or OOX 142 13/16 79 1/2 143 9/16 80 20
12/0T X R.H. OXO 145 7/8 79 1/2 146 5/8 80 20
12/0Q X R.H. OXXO 139 3/4 79 1/2 140 1/2 80 10 or 15
5/0 X 8/0 R.H. XO or OX 59 1/4 95 1/2 60 96 12 or 18
6/0 X 8/0 R.H. XO or OX 71 1/4 95 1/2 72 96 12 or 18
8/0 X 8/0 R.H. XO or OX 95 1/4 95 1/2 96 96 24
9/0 X 8/0 R.H. XOO or OOX 106 13/16 95 1/2 107 9/16 96 12 or 18
9/0 X 8/0 R.H. OXO 109 7/8 95 1/2 110 5/8 96 12 or 18
10/0Q X 8/0 R.H. OXXO 115 3/4 95 1/2 116 1/2 96 12 or 18
12/0T X 8/0 R.H. XOO or OOX 142 13/16 95 1/2 143 9/16 96 24
12/0T X 8/0 R.H. OXO 145 7/8 95 1/2 146 5/8 96 24
12/0Q X 8/0 R.H. OXXO 139 3/4 95 1/2 140 1/2 96 12 or 18
SYSTEM DIM. ROUGH OPENING
THERMA-TRU PATIO DOOR SIZING SPECIFICATIONS
43
Anchor Screw
#10 x 1 PPH SMS½"
Anchor Screw
#10 x 2 PPH SMS½"
Frame Assembly Screw
#10 x 3" PFH SMS
Rough Opening Screw
#8 x 3" PPH
Mortise Screw
#8 x 1" PFH MS
Handle Set Keeper Screw
#10 x 1 PPH SMS½"
Colored Handle Set Screw
#10 x 2 1/4" Phillips Oval MS
Colored Foot Bolt Screw
#8 x 1 S.S. PPH SMS½"
Colored Foot Bolt Screw
#8 x 9/16" S.S. PPH SMS
Colored Foot Bolt Keeper
Screws
#8 x 1" S.S. PPH SMS
SCREW CHART
Handle Set Screw
#10 x 7/16" PH Hex Drive MS
Transom & M.E.U. Screw
#8 x 2" PPH SMS
Astragal Screw
#10 - 32 x 1 1/4" PPH SS MS
#6 x 3/4" TEK PH Screw
1687 Woodlands Dr. Maumee, OH 435371-800-THERMATRU (843-7628)
www.thermatru.com
© 2005 Therma-Tru Corp. Part # SLBOOK0412-31-04
Therma-Tru Doors is an operating company of Fortune Brands, Inc.