FACADE SOLUTIONS
TECHNICAL DATA SHEET
ARBO EPDM MEMBANESYSTEM
ARBO MEMBRANE FACADE SEALINGSYSTEM
PRODUCTS:
ARBO EPDM MEMBRANE
ARBOSA
ARBO MEMBRANE ADHESIVE
Internal SealArbonwric MP10
Arbo EPDMFor Metal WindowsAM) CurtainWalling
External SealArtHMillOMArbo.il XL! 099 (*Stope)•Contact Adshead RatclifleTechnical Sen ices.
INTRODUCTION
Following the introduction of document L, it hasbecome a requirement to provide a robust seal tothe internal interfaces between different fa?adecomponents of a construction. The purpose of thisseal is to reduce heat and air leakage from abuilding and to help prevent interstitialcondensation.
To aid rapid construction techniques, contractorsdemand that a building is made substantiallywaterproof as early as possible during construction.The use of the Arbo EPDM system plays animportant role in achieving this aim. The membraneis usually applied between the window or curtainwall and the outside of the inside wall.
Increasing standards demanded by buildinginsurance companies on new constructions andimpending legislation means that window sealsmust incorporate additional robust seals and use ofan external sealant only will not be permitted as asingle line of defence against water ingress.
The Arbo Membrane system is designed to offer afully compatible solution to this detail that not onlyprevents water and air leakage but uses sealants andadhesives which are safe and solvent free. Drawingon the wealth of experience of laboratory testing wecan provide a system that will not affect sensitivesubstrates such as natural stone. The ArboMembrane system does not affect solvent sensitivepaint finishes and is compatible with other Arbosealants which may come into contact with theEPDM system.
ARBO MEMBRANE ADHESIVE
ARBO MEMBRANE EPDM
Available in 0.75 mm thickness, 25 metre lengthrolls.Width - 100mm to 700mm in 50mm increments.Other widths, up to 1400mm are available onrequest. Please contact Adshead Ratcliffe Sales forfurther information.
TECHNICAL INFORMATION
Complies to EN 14909
Tensile Strength
Elongation
Modulus 300%(Mpa)Hardness (ShoreA)Tear strength(KN/m)
Low temperatureflexibilityWater vapourpermeabilityReaction to fire
Water tightnessDurability( heatageing)Durability(alkali)OzoneUVLife Expectancy
EN12311-2B
EN12311-2B
EN12311-2B
EN 495-5
EN13501-1
EN1928EN 1928
EN12113-2
Based onSKZ 2001
study
> 9N/mm2
> 400
> 6N/mm2
50-70
> 35
-70 C
40,000 n
Class E
PassPass
Pass
ResistantResistant50 years
Recommended for factory and site application
A unique single pack elastomeric thixotropicadhesive material based upon modified polymertechnology. Formulated to exhibit high initial grabwithout the use of solvents to a wide variety ofsubstrates. Many applications will not require theuse of a primer although Arbo 2650 Primer isrecommended for porous surfaces such as brick,stone, blocks and some types of concrete.Compatible with PPC Aluminium, Upvc and otherfinishes. Has shown excellent adhesion to mostmineral boards and other membranes (For furtherinformation please contact Adshead RatcliffeTechnical Services Department).
This adhesive can be used without a terminator stripin most applications. Factory application towindows requires a mechanical fixing to aidproduction and transport.
For new or untested substrates please contactAdshead Ratcliffe Technical Services Department•who will be able to arrange adhesion tests.
The requirement for brushing is eliminated as theproduct is packed in 600 ml foils for quick, easyand clean application. Waste disposal costs aresignificantly reduced by the small volume of foilleft to dispose of once the foil pack has beenemptied.For further information please consult our MaterialSafety Data Sheet, www.arbo.co.uk
ARBQSA
Recommended for factory and site application
A unique single pack elastomeric adhesive sealantmaterial based upon silicone polymer technology.Formulated to exhibit good initial grab without theuse of solvents to a wide variety of substrates.Arbo 2650 Primer is recommended for poroussurfaces such as brick, stone, blocks and some typesof concrete.Compatible with PPC Aluminium and Upvc andother finishes.Excellent adhesion to both Arbo Membrane EPDMand other membranes (For further information
please contact Adshead Ratcliffe TechnicalServices Department).Terminator strips are recommended for factory andsome site applications.The requirement for brushing is eliminated as theproduct is packed in 600 ml foils for quick, easyand clean application. Waste disposal costs aresignificantly reduced by the small volume of foilleft to dispose of once the foil pack has beenemptied.For further information please consult our MaterialSafety Data Sheet, www.arbo.co.uk
For new or untested substrates please carry out onsite adhesion tests or contact Adshead RatcliffeTechnical Services Department who will be able toarrange laboratory adhesion tests free of charge
Application method
All surfaces to be coated must be clean, dry and insound condition.Ideally the building should be cloaked to minimisedampness during construction.However components can become dampLaboratory experiments have shown that whereporous substrates for example fibre boards becomedamp the adhesion of ARBO MA can be improvedby drying the surface with a dry cloth apply onecoat of 2650 primer and allow to dry.
Arbo SA is not recommended on damp surfaces.Porous surfaces to be primed with Arbo Primer2650Minimum recommended lap to window 20mmMinimum recommended lap to substrate 100 mmTerminator strips are recommended when applyingin deep laps at head and cillFor application recommended sequence is; cill,jambs, head.Apply by sealant gun in approximately 8 x 3mmbeads approximately 25 mm apart. Press onmembrane by using an ARBO roller to improvecontact between substrates and membrane.Lap and patch corners where necessaryAny holes or gaps in corners can be sealed withfurther application of adhesive
We recommend that edges of membrane are oversealedProduct cures by reaction with atmosphericmoisture.
It is advisable not to apply when surfaces are below5 degrees Centigrade especially in damp conditions.(For further information on application of sealantsand adhesives in cold weather please see our website or contact our technical department)
Ordering
ARBO SA and ARBO Membrane Adhesive areavailable in 600 ml foils, 20 foils per box. Bothproducts are available in Black only.One foil will cover approximately 20 linear metreson an 8mm x 3mm extruded bead.EPDM membrane is available in 0.75 mmthickness, 25 metre length rolls.Width - 100mm to 700mm in 50mm increments.For other widths, up to 1400mm please contactAdshead Ratcliffe Sales for further information.
ARBO Membrane EPDM sheet is cut to order.Please state quantity, width and total number ofrolls required in 25 metre lengths.
Important: The information in this leaflet is givenin good faith and based on results gained fromexperience and tests. However, allrecommendations or suggestions are made withoutguarantee since the conditions of use are beyondour control. Goods are supplied subject to theCompany's terms and conditions of sales, a copy ofwhich is available on request.
LIMITATIONSThis product is intended for vertical use only.Flat areas which are jointed with adhesives that aresubjected to ponding have not been tested andtherefore not recommended.Continuous membrane i.e. one piece no joints areallowed providing it is not subjected to traffic and islaid to a fall to shed water.For further information please contact technicalservices.
Adshead Ratcliffe & Co Ltd,Derby Road,Belper,DerbyshireDE56 1WJ,England.Telephone: 01773 826661Fax: 01773 821215Internet: www.arbo.co.uk
Review Date 25th March 2011