Download - Table of contents - SitOnIt
![Page 1: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/1.jpg)
Table of contents
![Page 2: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/2.jpg)
Prise Benching Assembly Instructions
Back to back kits PRI-BBEL
Single sided kits
PRJ.SSTS
9
PRI-SSMt
WIRE BASKETS
OPTIONAL
1
Peninsula kit
6
![Page 3: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/3.jpg)
Prise Benching Assembly Instructions (back to back)
13TOP GLIDE SPACER
LEG
STRETCHER BRACKET
MID-BRACKET
CROSS TUBE
CABLE TRAY CLIP
EXTRUSION END CAP
DIVIDER CLAMP
CABLE TRAY
LEG RAIL
LEG RAIL COVER
TOP SUPPORT-LARGE
MIDDLE SUPPORT
DIVIDER EXTRUSION
ALLEN KEY
5/16-18 UNC SCREW
14 1516
52
Install glides Attach divider clamps (7) to extrusion bar (14)- BBTS kit
Assemble legs (1) to leg rail (9) - BBEL kit
Attach cable tray clips (5) to cable tray (8) - BBTS kit
Assemble mid-bracket (2) toleg (1) - BBMI kit
![Page 4: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/4.jpg)
**IMPORTANT TO USE ALL BOLTS PROVIDED**
Attach stretcher brackets (3)to leg rails (9)
1. 2. Connect cross tubes (4) to mid brackets (2)& end legs.
3. Snap end covers (10) over leg rails
**DONT PUT SCREWS HEREUNTIL TOP SUPPORTS ARE PLACED**
![Page 5: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/5.jpg)
Install large top supports (11) to cross tubes (4) as shownin Fig. A
4.
Fig. A
Place middle support (12) for tops 60" & greater (no hardware, simply place on cross tube)*tops less than 60" wide, do not use part #12
5.
Drop in cable trays (8) as shown in Fig. B6.
Fig. B
**INSERT ONE SCREWON EACH SIDE OFCROSS TUBE**
![Page 6: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/6.jpg)
IMPORTANT TO USELONGER BOLTS HERE
Install extrusion (14) by attaching divider mounts to top supports as shown in Fig. C using long bolts.*center mount is not used on tops less than 60" wide
7.Fig. C
Install end caps on both ends of extrusions (Fig. D)8.
Fig. D
![Page 7: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/7.jpg)
Prise - Sliding top installation
If using sliding top function, please follow these steps.**please note that bases with returns & single sided setups will not allow sliding top function.
1. Each top needs 4 top glides. Insert glide through top support using the pre-drill pattern providedin the tops. (the glides are the parts highlighted yellow in Fig. A)
2. Follow orientation in Fig. B - drill screws provided through each glide.
Fig. AFig. B
Fig. C
![Page 8: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/8.jpg)
If adding returns, you need the following kits:- PRI-SSEL- PRI-PK
*Note that sliding top function will not work with returns
Prise Benching w/ returns
![Page 9: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/9.jpg)
Back to back typical power layout
![Page 10: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/10.jpg)
Prise Benching Assembly Instructions (single sided)
LEG
STRETCHER BRACKET
CROSS TUBE
WIRE BASKET
MID TOP SUPPORT
MID LEG CONNECTOR
LEG RAIL
LEG RAIL COVER
END TOP SUPPORT
ALLEN KEY
5/16-18 UNC SCREW
![Page 11: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/11.jpg)
![Page 12: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/12.jpg)
Install wire baskets (5) for wire management (1 or 2 per top)
![Page 13: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/13.jpg)
Single sided typical power layout
![Page 14: Table of contents - SitOnIt](https://reader033.vdocuments.us/reader033/viewer/2022061523/629f1cf6708e8651b54eca70/html5/thumbnails/14.jpg)