-
SYNTHESIS AND CHARACTERIZATION OF PENTACARBONYLACRYLOYLFERROCENETUNGSTEN(0) COMPLEX
A THESIS SUBMITTED TO THE GRADUATE SCHOOL OF NATURAL AND APPLIED SCIENCES
OF MIDDLE EAST TECHNICAL UNIVERSITY
BY
DİLEK AYŞE BOĞA
IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR
THE DEGREE OF MASTER OF SCIENCE IN
CHEMISTRY
JANUARY 2006
-
Approval of the Graduate School of Natural and Applied Sciences Prof. Dr. Canan Özgen Director I certify that this thesis satisfies all the requirements as a thesis for the degree of Master of Science. Prof. Dr. Hüseyin İşçi Head of Department This is to certify that we have read this thesis and that in our opinion it is fully adequate, in scope and quality, as a thesis for the degree of Master of Science. Prof. Dr. Saim Özkar Supervisor Examining Committee Members Prof. Dr. Hüseyin İşçi (METU,CHEM) Prof. Dr. Saim Özkar (METU,CHEM) Prof. Dr. Ceyhan Kayran METU,CHEM) Assoc. Prof. Dr. Özdemir Doğan (METU,CHEM) Prof. Dr. Yavuz İmamoğlu (Hacettepe Unv., CHEM)
-
iii
I hereby declare that all information in this document has been obtained and
presented in accordance with academic rules and ethical conduct. I also declare
that, as required by these rules and conduct, I have fully cited and referenced all
material and results that are not original to this work.
Name, Last name:
Signature:
-
iv
ABSTRACT
SYNTHESIS AND CHARACTERIZATION OF
PENTACARBONYLACRYLOYLFERROCENETUNGSTEN(0)
Boğa, Dilek Ayşe
MS., Department of Chemistry
Supervisor: Prof. Dr. Saim Özkar
January 2006, 53 pages
Pentacarbonylacryloylferrocenetungsten(0) complex was synthesized
photochemically from hexacarbonyltungsten(0) and acryloyferrocene (acfc). UV
irradiation of W(CO)6 in the presence of acryloylferrocene at 10 oC for 4 hours in n-
hexane solution generates the W(CO)5(η2-acfc) complex as the sole
monosubstitution product of the photolysis, as monitored by FT-IR spectroscopy.
The product complex could be isolated from the reaction solution and characterized
by IR, Raman, 1H-NMR, 13C-NMR spectroscopies, mass spectrometry and elemental
analysis. The complex was found to be unstable in solution and to decompose to the
parent W(CO)6 complex and free acryloylferrocene molecule. The instability of the
complex makes its isolation as analytically pure substance difficult.
In order to stabilize the tungsten-olefin bond, trimethylphosphite was
introduced as a donor ligand into the molecule. Thus, a complex containing a donor
-
v
ligand in addition to the olefinic ligand was prepared starting with W(CO)6,
trimethylphosphite, and acryloylferrocene. UV irradiation of W(CO)5[P(OMe)3] with
acryloylferrocene in n-hexane solution at room temperature generates
W(CO)4[P(OMe)3](η2-acfc), which was isolated from the reaction solution and
characterized by IR, 1H-NMR, 13C-NMR spectroscopies and mass spectrometry. The
complex was found to have a cis arrangement of four CO groups in the pseudo-
octahedral geometry. However, the cis-W(CO)4[P(OMe)3](η2-acfc) complex was
found to be less stable than W(CO)5(η2-acfc).
Keywords: acryloylferrocene, tungsten, carbonyl, trimethylphosphite, photolysis.
-
vi
ÖZ
PENTAKARBONİLAKRİLOİLFERROSENTUNGSTEN(0)’İN
SENTEZİ VE TANIMLANMASI
Boğa, Dilek Ayşe
Yüksek Lisans, Kimya Bölümü
Tez Yöneticisi: Prof. Dr. Saim Özkar
Ocak 2006, 53 sayfa
Pentakarbonilakriloilferrosentungsten(0) kompleksi, fotokimyasal olarak
hegzakarboniltungsten(0) ve akriloilferrosen (acfc) bileşiklerinden sentezlendi.
Akriloilferrosen eşliğinde W(CO)6 kompleksinin n-hegzan çözeltisinde 10 oC de 4
saat süre UV ışınlanması tek fotosübstitüsyon ürünü olarak W(CO)5(η2-acfc)
kompleksini oluşturdu. Fotokimyasal tepkime, FT-IR spektroskopisi ile izlendi.
Oluşan ürün W(CO)5(η2-acfc) kompleks tepkime ortamından izole edildi ve FT-IR,
Raman, 1H-NMR, 13C-NMR spektroskopisi, elemental analiz ve kütle spektrometrisi
yöntemleri kullanılarak tanımlandı. Kompleksin özellikle çözeltide pek kararlı
olmadığı ve W(CO)6 başlangıç kompleksi ile serbest akriloilferrosene dönüştüğü
gözlendi. Kompleksin bu kararsızlığı onun saf bir madde olarak çözeltiden
izolasyonunu güçleştirmektedir.
-
vii
Tungsten-olefin bağını kararlı hale getirmek amacıyla trimetilfosfit donör
ligand olarak molekülle tepkimeye sokuldu. Böylece, olefinik liganda ek olarak
donör ligand içeren bir kompleks, W(CO)6, trimetilfosfit ve akriolilferrosenden yola
çıkılarak hazırlandı. W(CO)5[P(OMe)3] kompleksinin n-hegzan çözeltisi içerisinde
10 oC de UV-ışınlanması, W(CO)4[P(OMe)3](η2-acfc) kompleksini oluşturdu.
Oluşan kompleks, tepkime çözeltisinden izole edilerek, IR, 1H-NMR, 13C-NMR
spektroskopileri ve kütle spektrometrisi yöntemleri kullanılarak tanımlandı.
Kompleksin dört CO grubuyla pseudo-oktahedral geometride, cis yapıda olduğu
gözlendi. Bununla birlikte, W(CO)4[P(OMe)3](η2-acfc) kompleksinin W(CO)5(η
2-
acfc) kompleksinden daha az kararlı olduğu gözlendi.
Anahtar kelimeler: akriloilferrosen, tunsgten, karbonil, trimetilfosfit, fotoliz.
-
viii
To my family
-
ix
ACKNOWLEDGMENTS
I would like to express my sincere gratitude to Prof. Dr. Saim Özkar for his
unceasing support, guides, understanding and supervision throughout in this study.
I would like to extend my gratitude to Prof. Dr. Ceyhan Kayran for her close
interest and valuable critism in the progress of this work.
I would like to thank Ercan Bayram, Sanem Koçak, Cüneyt Kavaklı, Ezgi
Keçeli, Mehmet Zahmakıran, Önder Metin, Fatma Alper, Ceyhun Akyol, Murat
Rakap and Pelin Edinç for their caring and encouragement during this study.
The last but not least, I would like to thank my family for their moral support
and helping me with any and every problem I encountered during the whole study.
-
x
TABLE OF CONTENTS
PLAGIARISM............................................................................................................iii
ABSTRACT...............................................................................................................iv
ÖZ...............................................................................................................................vi
ACKNOWLEDGMENTS..........................................................................................ix
TABLE OF CONTENTS............................................................................................x
LIST OF FIGURES...................................................................................................xii
LIST OF TABLES....................................................................................................xiv
CHAPTER
1. INTRODUCTION...........................................................................................1
2. BONDING.......................................................................................................9
2.1. Metal-Carbonyl Bonding..................................................................…....9
2.2. Metal-Olefin Bonding.............................................................................12
2.3.Metal-Phosphorus Bonding.....................................................................13
3. EXPERIMENTAL.........................................................................................15
3.1. Basic Techniques....................................................................................15
3.2. Physical Measurements..........................................................................19
3.2.1. Infrared Spectra.......………........…………………............................19
3.2.2. Raman Spectra.....................................................................................19
3.2.3. NMR Spectra.......................................................................................19
3.2.4. Mass Spectra........................................................................................20
3.2.5. Elemental Analysis..............................................................................20
3.3. Synthesis of complexes...........................................................................20
3.3.1.Synthesis of acryloylferrocene..............................................................20
3.3.2. Synthesis of pentacarbonylacryloylferrocenetungsten(0),
W(CO)5(η2-acfc)............................................................................................21
-
xi
3.3.3. Synthesis of tetracarbonylacryloylferrocenetrimethylphosphite-
tungsten (0), W(CO)4[(P(OCH3)3](η2-acfc)..................................................... 21
4. RESULTS AND DISCUSSION..........................................................................23
4.1. Synthesis and the characterization of the ligand, acryloylferrocene.........23
4.2. Synthesis and Characterization of the complexes.....................................28
4.2.1. Synthesis of the pentacarbonylacryloylferrocenetungsten(0),
W(CO)5(η2-acfc)..............................................................................................28
4.2.2. Synthesis and characterization of W(CO)4[(POCH3)3](acfc)
complex...........................................................................................................39
5.CONCLUSION.....................................................................................................48
6.REFERENCES......................................................................................................50
-
xii
LIST OF FIGURES
1.1. Sequential photolytic substitution of CO ligands in M(CO)6 (M = Cr, Mo and
W) by olefin................................................................................................................5
1.2.Acryloylferrocene (acfc).......................................................................................6
1.3. Photolytic CO substitution in W(CO)6 with acryloylferrocene forming the
product W(CO)5(η2-acfc)............................................................................................7
1.4. Formation of cis-W(CO)4[P(OCH3)3](η2-acfc) from the irradiation of
W(CO)5[P(OCH3)3] in the presence of acryloylferrocene (acfc) in n-hexane at
10 oC...........................................................................................................................8
2.1. Molecular orbital description of metal-carbonyl interaction .............................10
2.2. Molecular orbital diagram of M-CO bond.........................................................10
2.3. Competition for π-bonding in metal-carbonyl derivatives.................................11
2.4. Metal-alkene bonding.........................................................................................13
2.5. MO description of Metal-Phosphorous bonding................................................14
3.1 Nitrogen gas purification steps............................................................................17
3.2. Standard schlenk tube.........................................................................................17
3.3. The apparatus used for the photochemical reactions..........................................18
4.1. Synthesis of acryloylferrocene (acfc) by Friedel-Crafts acylation.....................23
4.2.Infrared spectrum of acryloylferrocene taken in n-hexane at room
temperature...............................................................................................................22
4.3. 1H NMR spectrum of acryloylferrocene in CDCl3...................................................................26
4.4. 13C-NMR spectrum of acryloylferrocene in CDCl3 ...........................................27
4.5. Synthesis of W(CO)5(η2-acfc)...........................................................................28
4.6. IR spectrum of W(CO)6 in n-hexane before irradiation....................................29
4.7. IR spectrum of W(CO)5(η2-acfc) formed after 4 hours irradiation of W(CO)6
in n-hexane solution..................................................................................................29
-
xiii
4.8. Infrared spectrum of W(CO)5(η2-acfc) in KBr pellet........................................31
4.9. Raman spectrum of W(CO)5(η2-acfc) in solid form...........................................31
4.10. 1H-NMR spectrum of W(CO)5(η2-acfc) in CD2Cl2..........................................33
4.11. 13C-NMR spectrum of W(CO)5(η2-acfc) in CD2Cl2.........................................35
4.12. 13C-NMR spectrum of W(CO)5(η2-acfc) taken in CD2Cl2 solution two days
after synthesis............................................................................................................37
4.13. Mass spectrum of W(CO)5(η2-acfc): Molecular peak of W(CO)5(η
2-acfc)
complex, observed (top) and calculated (bottom).....................................................38
4.14. IR spectrum of W(CO)4[P(OCH3)3](η2-acfc) in n- hexane............................40
4.15. 1H-NMR spectrum of cis-W(CO)4[P(OCH3)3](η2-acfc) taken in CD2Cl2
solution......................................................................................................................43
4.16. 13C-NMR spectrum of cis-W(CO)4[P(OCH3)3](η2-acfc) taken in CD2Cl2
solution......................................................................................................................44
4.17. CO region of 13C-NMR spectrum of cis-W(CO)4[P(OCH3)3](η2-acfc)
taken in CD2Cl2 solution...........................................................................................45
4.18. Mass spectrum of cis-W(CO)4[P(OCH3)3](η2-acfc): Molecular peak of cis-
W(CO)4[P(OCH3)3](η2-acfc) complex, observed (top) and calculated (bottom)....46
4.19. Mass spectrum of cis-W(CO)4[P(OCH3)3](η2-acfc).......................................47
5.1. W(CO)5(η2-acfc)...............................................................................................48
-
xiv
LIST OF TABLES
4.1. Elemental analysis values and theoretical mass percentages of carbon and
hydrogen atoms in W(CO)5(η2-acfc)..........................................................................35
-
CHAPTER 1
INTRODUCTION
Organometallic compounds are defined as substances containing direct metal
carbon interaction. The variety of the organic moiety in such compounds is
practically infinite, ranging from alkyl substituents to alkenes, alkynes, carbonyls,
and aromatic and heterocyclic compounds.1
Organotransition metal chemistry is distinguished from the organometallic
chemistry of the main group metals by its greater versatility. Although reactive main
group organometallics generally add to carbonyl compunds and some activated
carbon-carbon double bonds, transition metal compounds frequently react with
unactivated, unsaturated organic compounds, often in a catalytic manner. The subject
of organotransition metal chemistry as a distinct area of chemistry was of relatively
little interest before about 1960. Even though the first recognized organometallic
complex, Zeise’s salt, K[PtCl3(C2H4)]⋅2H2O,2 was prepared in 1827, significant
interest in such compounds did not develop until after the structure of ferrocene was
determined in 1952,3 and it was subsequently realised that the transition metals
possessed the capability of forming a wide variety of isolable organometallic
compounds.4
The development of organometallic chemistry has occured unusually in the last
five decades. This development could be attributed to the relation between general
theory of structural chemistry and organometallic chemistry, which contributed to
generalization and broadening of certain concepts such as multicenter bonding and
cluster compounds. The continuing development of structural chemistry (including
1
-
structural organometallic chemistry) in turn stimulates the synthesis and structural
investigations of new organometallic compounds. Another important factor
influencing the intensification of research in this field is application of
organometallic compounds in organic synthesis, catalysis, and technology, for
example, preparation of metals and their new compounds.5
Metal π-complexes possess a relatively new type of direct carbon-to-metal
bonding that cannot be designated as one of the classic ionic, σ-, or π-bonds. It is
known that a large number of both molecules and ions such as mono- and diolefins,
polyenes, arenes, cyclopentadienyl ions, tropylium ions, and π-allylic ions can form
metal π−complexes with transition metal atoms or ions. In 1827 Zeise reported that
ethylene reacted with platinum(II) chloride to form a salt K(C2H4)PtCl3.2H2O which
was proven to be the first reported metal π-complex.6
A common feature of the extensive class of π-complexes is the fact that the
L→M donor as well as the L←M acceptor interaction utilizes ligand orbitals which
−with regard to the intra-ligand bond − have π-symmetry. The ligand-metal bond in
π-complexes always contains an L←M π-acceptor component; the L→M donor
contribution can have σ-symmetry (monoolefins) or σ- or π-symmetry (oligoolefins,
enyl ligands, arenes and heteroarenes). Olefin complexes are widespread among
transition metals. These complexes play an important role in reactions that are
catalyzed by organotransition-metal compounds, such as hydrogenation,
oligomerization, polymerization, cyclization, hydroformylation, isomerization, and
oxidation.7
Transition metal carbonyls are among the longest known classes of
organometallic compounds. They are common starting material for the synthesis of
other low-valent metal complexes, especially clusters. The carbonyl ligand can not
only be substituted for a large number of other ligands (Lewis bases, olefins, arenes),
but the remaining CO groups stabilize the molecule against oxidation or thermal
2
-
decomposition. Metal carbonyl derivatives play an important role as intermediates in
homogeneous catalysis. Carbonyl groups are also useful probes for determining the
electronic and molecular structure of organometallic species by spectroscopic
methods.7 The vibrational spectra of metal carbonyls have proved particularly
informative. The CO stretching bands observed in the infrared and Raman spectra are
to a good approximation specific group frequencies. They are also sharp, sensitive to
environment, and commonly intense.8 The vibrations of individual MCO groups
interact strongly,9 so that the observed spectra are rich in well-resolved bands. The
number and pattern of these give information about molecular symmetry and
geometry, while the positions of the bands are related to bonding.10
Metal carbonyls are the compounds of transition metals with carbon monoxide
ligand. They find applications in many catalytic processes and in organic synthesis.
Thus, research on preparations, structures, and applications of metal carbonyls and
their derivatives has been intensive for several decades. The first metal carbonyl,
Ni(CO)4 , was prepared by A. Mond, G. Langer, and F. Quinke,11 in 1890 by the
reaction of metallic nickel with carbon monoxide. It has found application
immediately; it has been used for industrial preparation of pure nickel. Many other
carbonyls were synthesized shortly thereafter.12
Almost all of the transition metals form compounds in which carbon monoxide
acts as a ligand. There are three points of interests with respect to these compounds:
(1) Carbon monoxide is not ordinarily considered a very strong Lewis base and yet it
forms strong bonds to the metals in these complexes; (2) the metals are always in a
low oxidation state, most often formally in an oxidation state of zero, but sometimes
also in a low positive or negative oxidation state; and (3) the 18-electron rule is
obeyed by these complexes with remarkable frequency, perhaps 99% of the time.13
There are two methods for the synthesis of the Group 6 metalcarbonyl
derivatives starting with M(CO)6. The first method is the direct photolysis of
hexacarbonylmetal(0), M(CO)6, in the presence of an appropriate ligand L,
3
-
M(CO)6 + nL hν
M(CO)6-nLn + nCO Eqn 1.1
Photosubstitution of group 6 metal hexacarbonyls has been established to occur
with high quantum yield,14 which is the ratio of the number of molecules undergoing
photochemical process to the number of photons absorbed by the reactant, and has
found a wide range of applications15 including the preparation of carbonyl-olefin-
metal complexes.16
The second method is the thermal substitution of a labile ligand, such as
tetrahydrofuran (THF), in an intermediate compex which has already been generated
by photolysis of M(CO)6 with a respective ligand, L
M(CO)6 + THF hν / −CO
M(CO)5(THF) + L / - THF
M(CO)5L Eqn 1.2
In the case of olefins, photosubstitution appears to be the most convenient
route for the synthesis of carbonyl-olefin-metal complexes. The sequential
photosubstitution of CO in M(CO)6 by olefins has already been established by using
(E)-cyclooctene as the olefinic ligand.16 The photolysis of M(CO)6 in the presence of
an olefin is expected to yield the stable final product trans-M(CO)4(η2-olefin)2
through the intermediate M(CO)5(η2-olefin) and cis- M(CO)4(η2-olefin)2 as shown in
Figure 1.1.
4
-
MOC
OCCO
CO
hv
-CO
MOC
OC CO
CO
CO
CO / +
-CO / +
hv
hv
cis-M(CO)4(olefin)2 trans-M(CO)4(olefin)2
MOC
OC CO
CO
CO
MOC
OC CO
CO
Figure 1.1. Sequential photolytic substitution of CO ligands in M(CO)6 (M = Cr, Mo
and W) by olefin.
Ferrocene has been used in the synthesis of many new materials having
interesting properties.17,18 For instance, molecules containing ferrocene moiety have
been used as homogeneous catalysts,18 molecular sensors,19 molecular magnets,20
non-linear optic materials,21 and liquid crystals.22 The presence of ferrocene in a
molecule is expected to influence its electron transfer ability.23
Introducing the ferrocenyl moiety into an olefin ligand is expected to influence
the stability and catalytic properties of its complexes with the transition metal.
Vinylferrocene has already been employed as an olefin ligand containing ferrocenyl
unit.24 However, its Group 6 metal carbonyl complexes of the type M(CO)5(η2-
vinylferrocene) have been reported to be unstable, which can be considered as an
indication that they might be active catalyst.24 Another potential olefinic ligand
5
-
containing ferrocenyl moiety is acryloylferrocene (Figure 1.2.) which has been
recently isolated.25 Acryloyferrocene is an olefin bearing a carbonyl group in
addition to the ferrocenyl moiety. This carbonyl group may additionally interact with
the transition metal atom to which the olefin ligand is already coordinated through its
C=C bond. Therefore, this potential feature of acryloylferrocene prompted us to
investigate its carbonyl-metal complexes with the Group 6 elements.
In this study, it was aimed to synthesize W(CO)5(η2-acryloylferrocene), an
olefin-substituted metal carbonyl complex, by using acryloylferrocene (acfc) as the
olefinic ligand with an appropriate method. W(CO)5(η2 -acryloylferrocene) complex
contains two different metal atoms, iron and tungsten which can enhance the
catalytical properties of the complex.
Fe
O12
34
56
7
8
5'
4' 3'
2'
1'
Fig. 1.2. Acryloylferrocene (acfc)
Attempts to synthesize W(CO)5(η2-acryloylferrocene) by using thermal
substitution of a labile ligand failed. Neither W(CO)5(btmse) (btmse:
bis(trimethlsilyl)ethyne)26 nor W(CO)5(THF) (THF: tetrahydrofuran), gives the
olefin substituted product, rather W(CO)6 as the decomposition product.
6
-
The direct photochemical substitution method was found to be a convenient
route to synthesize the complex, W(CO)5(η2-acryloylferrocene). A solution of the
parent complex W(CO)6 in n-hexane was irradiated at 10 oC in the presence of
acryloylferrocene (acfc) to form W(CO)5(η2-acfc) which could be isolated from
reaction solution by crystallization. The complex W(CO)5(η2-acfc) was characterized
by IR, Raman, 1H-NMR, 13C-NMR spectroscopies, mass spectrometry and elemental
analysis.
WOC
OC CO
CO
CO
CO
+ acfc, hν
- COW
OC
OC CO
CO
CO FeO
Figure 1.3. Photolytic CO substitution in W(CO)6 with acryloylferrocene forming
the product W(CO)5(η2-acfc)
Since W(CO)5(η2-acfc) appears to be unstable, particularly in solution, we
attempted to stabilize the tungsten-acryloylferrocene complex by introducing
trimethylphosphite as a donor ligand into the molecule. For this purpose cis-
W(CO)4[P(OCH3)3](η2-acfc) was synthesized from the irradiation of
W(CO)5[P(OCH3)3] and acryloylferocene in n-hexane at 10 oC. The complex cis-
W(CO)4[P(OCH3)3](η2-acfc) was characterized by IR, 1H-NMR, 13C-NMR
spectroscopies and mass spectrometry. However this complex was found to be even
less stable than W(CO)5(η2-acfc) complex.
7
-
WOC
OC CO
COCO
P(OCH3)3
+ acfc, hν
- COFe
O
WOC
OC
COCO
P(OCH3)3
Figure 1.4. Formation of cis-W(CO)4[P(OCH3)3](η2-acfc) from the irradiation of
W(CO)5[P(OCH3)3] in the presence of acryloylferrocene (acfc) in n-hexane at 10 oC.
8
-
CHAPTER 2
BONDING
2.1. Metal –Carbonyl Bonding
One of the most commonly encountered ligand in organotransition metal
chemistry is carbon monoxide which forms complexes with these metals known as
metal-carbonyls. Its primary mode of attachment to the metal is through the carbon
atom.
The bonding of CO to a transition metal can be described in terms of two
synergic components; σ-dative bonding and π-back-bonding. The more σ-donation
by the carbonyl, the stronger π-back-bonding by the metal.27
i) σ-dative bonding: Two electron donation of the lone pair on carbon into
a vacant metal d-orbital; This electron donation makes the metal more
electron rich and in order to compensate for this increased electron
density, a filled metal d-orbital may interact with empty π*-orbital on the
carbonyl ligand to relieve itself of the added electron density.
ii) π-back-bonding: Effective overlap of the metal d-orbital and carbon
monoxide π*-orbital results in an extensive back-bonding. These
interactions are shown diagramatically in Figure 2.1.
9
-
M C O M C O
e m p t y d - o r b i t a l
f i l l e d σ - o r b i t a l
filledd-orbital
empty π*-orb i t a l
Figure 2.1. Molecular orbital description of metal-carbonyl interaction a) σ-dative
bonding, b) π-back-bonding
LnM LnM(CO) CO
Figure 2.2. Molecular orbital diagram of M-CO bond
10
-
Since π-back-bonding depends crucially on the electron density of the metal, it
not only strengthens the M-CO bond, but also provides a very sensitive probe for the
electronic characteristics of the metal center. Extensive back bonding in electron rich
complexes lowers the CO stretching frequency. This is consistent with the bonding
model, an increase in the electron density on the metal atom is delocalized over the
CO ligands, by populating the carbonyl π*-orbital thus weakening the CO bond.
Nevertheless, the converse is true if the complex is positively charged. Also the
presence of a strong σ-donor and weak π-acceptor ligand attached trans to CO ligand
in a mixed metal ligand carbonyl strengthens M-CO bond and weakens the C≡O
bond further, concomitantly. This weakening or strenthening is due to the sharing of
the same d-orbital by the carbonyl and the L ligand, trans to that carbonyl (π-
competition).13 (Figure 2.3)
Figure 2.3. Competition for π-bonding in metal-carbonyl derivatives. L denotes
the ligand which is stronger σ donor, but weaker π-acceptor than carbon
monoxide.
11
-
2.2. Metal – Olefin Bonding
The bond between ethylene molecule and the metal ion may be considered as a
dative σ bond to an available orbital on the metal. The bonding scheme is analogous
to that in carbon monoxide complexes in which there is a ligand to metal σ donation
and a reciprocal metal to ligand π donation. The extent of backbonding varies
depending on the metal, the substituents on ethylene, and the other ligands on the
metal.13
π-bonding molecular orbital of olefin is of σ-symmetry with respect to metal-
olefin interaction axis and, therefore, interacts with a σ-symmetry orbital on the
metal atom. Since the olefin donates electron to the metal atom through this
interaction, it causes an increase of the electron density on the metal. As a result of
interaction between a dπ metal orbital and antibonding π∗ alkene orbital, electron
density will be donated back to the olefin and this leads to an increase of electron
density on the π∗ orbital of the olefin and a decrease of electron density on the central
atom.28
12
-
C
M
C
M
C
C
empty σ-orbital filled alkene π-orbital filled d-orbital empty alkene π∗-orbital
(a) (b)
Figure 2.4. Metal-alkene bonding: a) alkene to metal σ-donation,
b) metal to alkene π-back donation.
2.3. Metal-Phosphorus Bonding
The bonding in phosphite ligands is similar to that of carbonyls, so it can be
thought of having two important components. The first one is σ-donation of the
phosphine lone pair to an empty orbital on the metal. The second component is back
donation from a filled metal dπ orbital to an empty d orbital on the phosphine ligand
(Figure 2.4.)
These ligands are somewhat different from carbonyl ligand regarding the type
of orbitals used for bonding to a metal, as phosphorus uses its d-orbitals for π-
interaction with metal while carbon monoxide uses its π* orbitals. The former is
called dπ-dπ and the latter is dπ-pπ bonding.29
13
-
Figure 2.4. MO description of Metal-Phosphorous bonding (R: CH3)
a) (OCH3)3P→Metal σ-bonding
b) Metal→P(OCH3)3 dπ-dπ bonding
14
-
CHAPTER 3
EXPERIMENTAL
3.1. Basic Techniques
Most of the organometallic compounds are air sensitive and tend to decompose
if not handled properly. In many cases oxidation occurs at a significant rate at room
temperature. This sensitivity to oxygen and water is usually more in solution than in
solid state. Therefore handling and all reactions of organometallic compounds should
be carried out under dry and deoxygenated nitrogen or argon atmosphere.
Organometallics may be handled almost as easily as ordinary compounds if the
reactions are carried out in the absence of oxygen. For this reason dry and
deoxygenated nitrogen or argon atmosphere is obtained by passing through nitrogen
or argon gas when the organometallic substances are open to air. Circulated nitrogen
or argon gas passes through some purification steps as shown in Figure 3.1. Firstly,
nitrogen or argon gas is allowed to pass through a catalyst (BASF R3.11,
Ludwigshafen, Germany) heated up to 120°C to remove oxygen and then dried
molecular sieves to remove its moisture. Last step is the bubbler which contains
glycerine to see the gas passage.
The basic techniques used during the experiments are;
(1) Vacuum line technique, which is used to get rid of the solvent by
evaporation in vacuum. Solvent is trapped in a tube which is immersed
into liquid nitrogen.
(2) Schlenk technique (Figure 3.2) in which a simple two-necked vessel
designed to permit passage of nitroen stream through the narrow neck
15
-
with the stopcock while using the wider neck without a stopcock for
operations such as inserting a spatula for scraping or removal of material
can be used. Depending on the objectives and the air sensitivity of the
compounds, one technique or a combination of techniques are used. The
thermal reactions were performed in a reaction flask with nitrogen
connection.
(3) Crystallization technique,30 is commonly used for isolation and
purification of products.
16
-
Figure 3.1. Nitrogen gas purification steps
Figure 3.2. Standard schlenk tube
17
-
Photochemical reactions were performed with a special glass apparatus having
two parts; an inner part in which a Mercury-Arc Lamp (Hg-Tauchlampe TQ-150)
was immersed and an outer part where water was circulated (Figure 3.3).
Figure 3.3. The apparatus used for the photochemical reactions
a) inner part
b) Mercury lamp,
c) Outer part
d) Water inlet,
e) Water outlet,
f) Nitrogen gas inlet,
g) Nitrogen gas outlet.
18
-
All solvents used were purified and dissolved oxygen was removed by
refluxing over metallic sodium except CH2Cl2 under nitrogen atmosphere for 2 to 3
days before use. CH2Cl2 was refluxed over phosphorus pentoxide for purification.
All solvents, ferrocene, acryloyl chloride, trimethylaluminum,
ethylaluminumdichloride, hexacarbonyltungsten were purchased from Aldrich,
trimethylphosphite was purchased from Ventron.
3.2. Physical Measurements
3.2.1. Infrared Spectra
Infrared spectra of the complexes were recorded from their dichloromethane or
hexane solutions using a Specac IR-Liquid cell with CaF2 windows on a Nicolet 510
FTIR Spectrometer instrument with Omnic software.
3.2.2. Raman Spectra
The Raman spectrum of the W(CO)5(η2-acfc) complex in solid form was
recorded by using a Bruker FRA 106/S Spectrometer with Opus software.
3.2.3. NMR Spectra
The 1H-NMR and 13C-NMR spectra of the acryloylferrocene molecule and the
complexes were recorded from their CDCl3 or CD2Cl2 solutions, on a Bruker-
Spectrospin DPX 400 Ultrashield NMR Spectrometer with Avance software.
Samples of the complexes were particularly prepared under nitrogen atmosphere. All
the chemical shift values were given relative to the signal of TMS used as an internal
reference.
19
-
3.2.4. Mass spectra
FAB-MS was taken on a Fisons VG Autospec with m-nitrobenzylalcohol as
matrix at Colorado State University, Fort Collins, USA.
3.2.5. Elemental Analysis
Elemental analysis of W(CO)5(η2-acfc) was carried out by using LECO CHNS-
932 instrument at METU Central Laboratory.
3.3. Synthesis of complexes
3.3.1. Synthesis of acryloylferrocene
Acryloylferrocene was prepared according to the literature procedure.25 To a
stirred solution of ferrocene (1,216 g, 6,98 mmol) and acryloylchloride (0.624 mL,
8.37 mmol) in CH2Cl2 (21.36 mL) at 0 oC was added Me3Al (1.602 mL, 3.47 mmol)
and EtAlCl2 (6.42 mL, 6.98mmol) drop by drop over 10 min consecutively. The
resulting mixture was stirred for another 20 min at this temperature. At the end of
this time, deep blue colored reaction mixture was hydrolized with water , and more
CH2Cl2 was added to the reaction flask. Two layers were separated, and the aqueous
layer was extracted with CH2Cl2. The combined organic layers were dried over
MgSO4, concentrated, and purified by column chromatography on silica gel. (1.34 g,
80% yield). IR (n-hexane) ν(CO)= 1665.1 cm–1. 1H NMR (CDCl3) δ= 6.74 (dd, H7,
J= 17.0 and 10.3 Hz), δ= 6.38(dd, H8 (trans to H7), J= 17.0 and 1.7 Hz), δ= 5.64 (dd,
H8' (cis to H7), J= 10.3 and 1.7 Hz), δ= 4.76 (t, H1, H4, J= 1.7 Hz), δ= 4.50 (t, H2,
H3, J= 1.7 Hz), δ= 4.12 (s, H1'-H5'). 13C-NMR (CDCl3) δ= 193.5 (C6), δ= 133.4
(C7), δ= 126.7 (C8), δ= 80.1 (C5), δ= 73.1 (C1,C4), δ= 70.4 (C2,C3), δ= 70.1 (C1'-
C5')
20
-
3.3.2. Synthesis of pentacarbonylacryloylferrocenetungsten(0), W(CO)5(η2-acfc)
W(CO)5(acfc) was synthesized photochemically by the direct photolysis of
W(CO)6 with acryloylferrocene in n-hexane solution. For this purpose 478.5 mg
(1.36 mmol) W(CO)6 was dissolved in n-hexane (150 mL) and 327.6 mg (1.36
mmol) acfc was added into the solution (every hour 25% of the ligand was added to
the medium in order to prevent precipitation of unreacted ligand during the reaction).
The solution was irradiated for 4 hours at room temperature. The reaction was
followed by IR spectroscopy. When the reaction was completed volatiles were
evaporated under vacuum and the dark red residue dissolved in n-hexane and the
solution was left overnight at –35 oC. The red precipitate was seperated from the
supernatant solution and was dried under vacuum. (0.2 g, 26% yield). Anal. Calcd.
for C18H12O6WFe (M = 563.9): C, 38.30; H, 2.13; Found: C, 38.85; H, 2.26%. MS:
m/z 563.9 (M+). IR (n-hexane) ν(CO)= 2091.0, 2013.2, 1974,6 and 1955.9 cm-1 . IR
(KBr pellet) ν(CO)= 2083.8, 1960.2, 1943.2, 1920.5 cm-1. Raman ν(CO)= 2084.4,
2007.9, 1964.2, 1944.5 and 1917.5 cm-1. 1H NMR (CD2Cl2) δ= 4.99 (m, H1), δ= 4.95
(m, H7), δ= 4.94 (m, H4), δ= 4.71 (m, H2), δ= 4.66 (m, H3), δ= 4.14 (d, H8, J=17.9
Hz), δ= 4.30 (s, H1'-H5') and δ= 3.80 (d, H8', J=12.6 Hz). 13C-NMR (CD2Cl2), δ=
202.4 (CO trans to acfc), δ= 195.2 (CO cis to acfc), δ= 194.4 (C6, CO of acfc
ligand), δ= 78.94 (C5), δ= 73.50 (C2), δ= 73.13 (C3), δ= 70.56 (C1'-C5'), δ=
70.28 (C7), δ= 69.86 (C1), δ= 69.33 (C8), δ= 68.63 (C4)
3.3.3. Synthesis of tetracarbonylacryloylferrocenetrimethylphosphitetungsten(0),
W(CO)4[(P(OCH3)3](η2-acfc)
W(CO)4[(P(OCH3)3](η2-acfc) was prepared from irradiation of
W(CO)5(POCH3)3 with acryloylferrocene at 10 oC. W(CO)5(POCH3)3 was prepared
according to the literature procedure.31 1.0 g (2.8 mmol) W(CO)6 was dissolved in
150 mL tetrahydrofuran (THF) and the solution was irradiated in a special glass
apparatus used for photochemical reactions for about 4 hours at 10 oC. During the
21
-
irradiation, nitrogen gas was allowed to pass through the solution in order to remove
the free CO from the reaction medium. The reaction was followed by IR
spectroscopy. After all W(CO)6 was converted to W(CO)5(THF), 0.33 mL (2.8
mmol) trimethylphosphite, P(OCH3)3 was added to the reaction vessel and the
solution was stirred overnight at room temperature. After the completion of the
ligand substitution reaction, the solvent was evaporated under vacuum and solid
residue was obtained. The W(CO)5(POCH3)3 complex was crystallized from n-
hexane solution over dry ice. Yellow-white W(CO)5(POCH3)3 crystals were obtained
and identified by IR spectroscopy. ν(CO)= 2080.5, 1989.8, 1962.9, 1950.6 and
1919.3 cm-1.
To prepare W(CO)4[P(OCH3)3](η2-acfc) complex; 637 mg (1.44 mmol)
W(CO)5P(OCH3)3 was dissolved in n-hexane and 343 mg (1.44 mmol)
acryloylferrocene was added to the medium and the reaction mixture was irradiated
about 4 hours at 10 oC. The reaction was followed by IR spectroscopy. After the
reaction was completed the solvent was evaporated in vacuum. Solid residue was
dissolved in n-hexane and the solution was left overnight at –35 oC.
W(CO)4[(P(OCH3)3](η2-acfc) complex was seperated from the solution and dried
under vacuum. (0.14 g, 15% yield). MS: m/z 660.0 (M+). IR(n-hexane) ν(CO) =
2050.7, 1966.3, 1943.8, 1925.6 cm–1. 1H NMR (CD2Cl2) δ= 4.92 (H1), δ= 4.78 (H7),
δ= 4.59 (H2), δ= 4.55 (H3), δ= 4.51 (H8), δ= 4.24 (H1'-H5'), δ= 4.18 (H4), δ= 3.68
(d, P(OCH3)3, J(31P-13C)= 14 Hz), 3.56 (H8'). 13C-NMR (CD2Cl2) δ= 198.06 (s, C6),
δ= 207.26 (d, CO trans to acfc, J(31P-13C)= 16.4 Hz), δ= 204.50 (d, CO trans to
trimethylphosphite, J(31P-13C)= 27.3 Hz), δ= 197.37 (d, CO cis to acfc and
P(OCH3)3, J(31P-13C)= 11), δ= 196.97 (d, CO cis to acfc and P(OCH3)3, J(31P-13C)=
10.9 Hz), δ= 79.99 (C5), δ= 72.64 (C1), δ= 72.42 (C4), δ= 70.31 (C1'-C5'), δ= 69.87
(C2), 69.34 (C3), 69.03 (C7), δ= 62.49 (C8), δ= 52.85 (d, P(OCH3)3, J(31P-13C)= 5.4
Hz).
22
-
CHAPTER 4
RESULTS AND DISCUSSION
4.1. Synthesis and the characterization of the ligand, acryloyferrocene
Acryloylferrocene was synthesized by the procedure given in the literature.25
First, ferrocene was dissolved in CH2Cl2 solution and acryloylchloride was added to
the solution at room temperature. Then the solution was cooled down to 0 oC and
Me3Al and EtAlCl2 was added to the medium dropwise, subsequently. The resulting
mixture was stirred for 20 minutes at this temperature. Then, the reaction mixture
was hydrolyzed with water and more CH2Cl2 was added to the reaction flask. Two
layers were seperated and the aqueous layer was extracted with CH2Cl2. The
combined organic layers were dried over Mg2SO4 and purified by column
chromatograpy on silica gel.
FeEtAlCl 2-AlMe 3
Fe
Cl
O
O
Figure 4.1. Synthesis of acryloylferrocene (acfc) by Friedel-Crafts acylation
The resulting solid acryloylferrocene was identified by IR, 1H NMR and 13C
NMR spectroscopies. The IR spectrum (Figure 4.2.) exhibits a characteristic
absorption band at 1665.05 cm-1 for CO stretching.
23
-
Figure 4.2. Infrared spectrum of acryloylferrocene taken in n-hexane at room
temperature
1H NMR and 13C NMR spectra were also taken to identify the synthesized
acryloylferrocene molecule. In the 1H NMR spectrum (Figure 4.3.) six different
signals were observed for the six different protons of the molecule. The signal at 6.74
ppm belongs to the CH-α (Η7) proton. The signal at 6.38 ppm belongs to the olefinic
proton trans to CH-α (H8) and the signal at 5.64 ppm belongs to the olefinic proton
cis to CH-α (H8') . In the ferrocenyl region three different signals were observed.
The signals at 4.76 ppm and at 4.50 ppm belong to the monosubstituted
cyclopentadienyl ring (H1,H4 and H2,H3, respectively) and the signal at 4.12 ppm
belongs to the 5H of the unsubstituted ferrocenyl ring (H1'-H5'). The protons on the
monosubstituted cyclopentadienyl ring resonates at lower field than the five equal
protons on the unsubstituted cyclopentadienyl ring, because of the electron
withdrawing effects of the substituents. The protons of the monosubstituted ring
24
-
closer to the electron withdrawing group should be less shielded, so they give a peak
at lower magnetic field.
In the 13C-NMR spectrum (Figure 4.4.), the signal at 193.5 ppm belongs to the
carbonyl carbon (C6) of the molecule. The signals at 133.4 ppm and ppm 126.7 can
be assigned to the olefinic carbons of the molecule (C7 and C8, respectively). The
signals at 80.1 ppm, 70.4 ppm and 73.1 ppm belong to the monosubstituted
cyclopentadienyl ring of the ferrocenyl moiety (C5; C1,C4 and C2,C3, respectively).
Because of the electron withdrawing effect of the substitution the ipso carbon
resonates at lower field than the other carbon atoms in the substituted ferrocenyl part
of the molecule. The signal at 70.1 ppm belongs to the five equal carbon atoms of the
unsubstituted cyclopentadienyl ring of the ferrocenyl moiety (C1'-C5').
25
-
F
igur
e 4.
3. 1 H
-NM
R sp
ectru
m o
f acr
yloy
lferr
ocen
e in
CD
Cl 3
26
-
Fi
gure
4.4
. 13 C
-NM
R sp
ectru
m o
f acr
yloy
lferr
ocen
e in
CD
Cl 3
27
-
4.2. Synthesis and Characterization of the complexes
4.2.1. Synthesis of the pentacarbonylacryloylferrocenetungsten(0), W(CO)5(η2-acfc)
Synthesis of the W(CO)5(η2-acfc) complex was carried out by the
photochemical reaction of W(CO)6 and acryloylferrocene at room temperature. The
photosubstitution of one of the CO groups in W(CO)6 with acryloylferrocene
resulted in the formation of W(CO)5(acfc).
WOC
OC CO
CO
CO
CO
acfc, hν
- COW
OC
OC COC
O
CO FeO
Fig. 4.5. Synthesis of W(CO)5(η2-acfc)
W(CO)6 was dissolved in distilled n-hexane and acryloylferrocene was added
into the solution. The solution was irradiated for about 4 hours at room temperature.
The decrease in the concentration of the reactant, W(CO)6, and the increase in the
concentration of the product, W(CO)5(η2-acfc), was monitored by means of IR
spectra (Figure 4.6. and Figure 4.7.) When the gradual decrease in the signal of
hexacarbonyltungsten(0) ceased, the irradiation process was stopped. After
evaporation of volatiles in vacuum, the residue was dissolved in n-hexane and the
solution was left overnight at –35 oC. Dark red precipitates were seperated from the
supernatant solution, dried in vacuum and characterized by IR, Raman, 1H-NMR and 13C-NMR spectroscopies, mass spectrometry and elemental analysis.
28
-
Figure 4.6. IR spectrum of W(CO)6 in n-hexane before irradiation
Figure 4.7. IR spectrum of W(CO)5(η2-acfc) formed after 4 hours irradiation of
W(CO)6 in n-hexane solution
29
-
The IR spectrum of the product, W(CO)5(η2-acfc) complex, which was taken in
n-hexane, shows four prominent peaks at 2091.0, 2013.2, 1974.6 and 1955.9 cm-1.
Five IR active CO stretching vibrations [3A1+B1+B2] are predicted under C2v
symmetry. However, one of the A1 mode should be intrinsically weak in intensity
and may remain unobserved or barely observable. According to the spectrum a local
C2v symmetry can be assigned to the W(CO)5 moiety of the complex. Besides these
four absorption bands, a peak at 1983.0 cm-1 was observed in the IR spectrum taken
from solution. This peak was attributed to the hexacarbonyltungsten(0) complex. The
IR spectrum of the complex taken in KBr pellet (Figure 4.8.), doesn’t show the
absorption band at 1983.0 cm-1. According to this result, it can be concluded that the
complex is not stable in solution and decomposes into hexacarbonyl complex. The
CO stretching frequency of the carbonyl group for the acfc molecule shifts from
1665.05 cm-1 to 1654.7 cm-1 in the W(CO)5(η2-acfc) complex. This result also shows
that acryloylferrocene is coordinated to the complex. Since the shift in the CO
stretching frequency is relatively small (about 10 cm-1), acryloylferrocene must be
coordinated to the tungsten through C=C bond, not through carbonyl oxygen. The
latter coordination would cause a remarkably large shift in the CO stretching
frequency of the acryloylferrocene ligand.
In Raman spectrum which was also taken from the solid sample (Figure 4.9.)
characteristic hexacarbonyl peak at 1999 cm-1 was not observed. All of the five CO
stretching bands of the W(CO)5 unit are observable, however, one band at 1964.2
cm-1 is intrinsically weak in the Raman spectrum: ν(CO) = 2083.9, 2007.7, 1964.2,
1943.7 and 1917.5 cm-1. Additionally, a band at 1647.3 cm-1 is observed for the CO
stretching of the carbonyl group of the acryloylferrocene ligand. The CO stretching
frequencies recorded in the IR and Raman spectra differ from each other slightly as
they have been taken in different media.
30
-
Figure 4.8. Infrared spectrum of W(CO)5(η2-acfc) in KBr pellet
4.9. Raman spectrum of W(CO)5(η2-acfc) in solid form
31
-
The 1H-NMR spectrum of W(CO)5(η2-acfc) in CD2Cl2 (Figure 4.10.), shows
two doublets and a multiplet for the three olefinic protons of the acryloylferrocene
ligand at 4.95, 4.14 and 3.80 ppm, respectively. Compared to the free
acryloylferrocene molecule, the shift of the olefinic proton signals toward higher
magnetic field verifies the coordination of acryloylferrocene to the metal. Very weak
signals observed at 6.85, 6.40, 5.73 ppm show the existence of free acryloylferrocene
as impurity. Consequently, the coordination shifts of the olefinic protons are
∆δ= 1.90 ppm, ∆δ= 2.26 ppm, ∆δ= 1.93 ppm, respectively. The relatively large
coordination shift of the olefinic protons shows that acryloylferrocene coordinates to
the metal through its C=C double bond.
32
-
F
igur
e 4.
10. 1
H-N
MR
spec
trum
of W
(CO
) 5(η
2 -ac
fc) i
n C
D2C
l 2
33
-
The 13C-NMR spectrum of W(CO)5(η2-acfc) taken in CD2Cl2 (Figure 4.11.),
gives five signals in the carbonyl region. The comparison with literature data shows
that the signal at 191.6 ppm32 is due to the W(CO)6 while the signal at 196.0 ppm is
attributed to the carbonyl carbon of the free acryloylferrocene molecule. The most
intense signal at 195.2 ppm is assigned to the four CO groups cis to the
acryloylferrocene ligand, while the signal at 202.4 ppm is assigned to the CO group
trans to the acryloylferrocene ligand. The remaining signal at 194.4 ppm is due to the
carbonyl carbon of the acryloylferrocene ligand in the complex. The signals at
δ 78.94, 73.50, 73.13, 70.56, 69.86 and 68.63 can be attributed to the ferrocenyl
carbons of the ligand. The signals observed at δ 70.28 and δ 69.33 belong to the
olefinic carbons of the acryloylferrocene ligand. When it is compared with the 13C-
NMR spectrum of the free acryloylferrocene molecule, the coordination shifts of
olefinic carbons are ∆δ= 63.1 and 57.4 ppm, respectively, while the shift of the
carbonyl carbon of the ligand in the complex is ∆δ= 2.6 ppm. The large coordination
shift of the olefinic carbon signals shows that acryloyferrocene molecule coordinates
to the metal through its C=C double bond.
34
-
F
igur
e 4.
11.13
C-N
MR
spec
trum
of W
(CO
) 5(η
2 -ac
fc) i
n C
D2C
l 2
35
-
In order to understand the stability of the complex, 13C-NMR spectrum was
taken again two days later. In the characteristic CO region of the spectrum (Figure
4.12.) it is clear that the signal of W(CO)6 at 191.60 ppm and the signal for the
carbonyl group of the free acryloylferrocene molecule at 195.17 ppm increase. This
increase explicitly shows that the complex is unstable in the solution and decompose
into hexacarbonyltungsten(0) and acryloylferrocene.
Another characterization technique, mass spectroscopy, was used to identify
the W(CO)5(η2-acfc) complex. Figure 4.13. shows the mass spectrum of the
complex. The calculated molecular weight of the complex fits to the experimentally
observed value of 563.9 g/mol. Furthermore, the characteristic isotop distribution
pattern observed for the complex fits to the simulated one for the C18H12O6WFe
formula. So, it can be concluded that the W(CO)5(η2-acfc) complex was formed and
determined by mass spectroscopy.
Table 4.1. gives the results of the elemental analysis for the W(CO)5(η2-acfc)
complex. The experimentally found values are slightly different from the calculated
ones. This difference may arise from the fact that the complex is not stable
particularly in air.
Table 4.1. Elemental analysis values and theoretical mass percentages of carbon and
hydrogen atoms in W(CO)5(η2-acfc)
ATOM
EXPERIMENTAL %
THEORETICAL %
CARBON 38.85 38.30
HYDROGEN 2.26 2.13
36
-
Fig
ure
4.12
. 13 C
-NM
R sp
ectru
m o
f W
(CO
) 5(η
2 -ac
fc) t
aken
in C
D2C
l 2so
lutio
n tw
o da
ys a
fter s
ynth
esis
37
-
Figure 4.13. Mass spectrum of W(CO)5(η2-acfc): Molecular peak of W(CO)5(η2-
acfc) complex, observed (top) and calculated (bottom).
38
-
4.2.2. Synthesis and characterization of W(CO)4[P(OCH3)3](η2-acfc) complex
The presence of a donor ligand can affect the bond between metal and ligand in
the complex sterically and electronically. W(CO)5(η2-acfc) could not be isolated as
analytically pure substance from the solution because it is unstable with respect to
decomposition to W(CO)6 and free acryloylferrocene. Therefore, introducing a donor
ligand to the complex may increase the stability of the metal-olefin. A donor ligand
makes the metal center electron rich and, hence, increase the back-donation from
metal to olefinic ligand. Trimethylphosphite was used as donor ligand. Thus,
W(CO)4[P(OCH3)3] (η2-acfc), a complex containing a donor ligand in addition to the
olefinic ligand, could be synthesized photochemically starting with
W(CO)5[P(OCH3)3].
W(CO)5[P(OCH3)3] was prepared by the thermal substitution reaction of
W(CO)5(THF) with trimethylphosphite. W(CO)5(THF) was photogenerated by UV-
irradiation of W(CO)6 in THF solution. The reaction was followed by IR
spectroscopy. During the irradiation process THF substituted for one carbonyl group.
After the monosubstitution reaction was completed, the irradiation was stopped,
trimethylphosphite was added to the solution and was stirred overnight at room
temperature. The thermal substitution of tetrahydrofuran with trimethylphosphite
was also monitored by taking the IR spectrum. Following the formation of the
W(CO)5[P(OCH3)3] complex, the solvent was evaporated to isolate the complex. The
isolated solid was crystallized in n-hexane solution over dry ice. Yellow-white
W(CO)5[P(OCH3)3] crystals were obtained and identified by IR spectrum: ν(CO)=
2080.5, 1989.8, 1962.9, 1950.6 and 1919.3 cm-1.
Then, W(CO)4[P(OCH3)3](η2-acfc) complex was prepared photochemically by
the reaction of W(CO)5[P(OCH3)3] with acryloyferrocene in n-hexane solution. The
W(CO)4[P(OCH3)3](η2-acfc) complex was characterized by means of IR, NMR
spectroscopies and mass spectrometry. The IR spectrum of the complex was taken in
n-hexane (Figure 4.14.) and shows four prominent absorption bands at 2050.7,
39
-
1966.7, 1943.8 and 1925.6 cm-1 for the CO stretching .The observation of four bands
indicates a cis arrangement of the W(CO)4 moiety, which has then a Cs local
symmetry with 3 A' + A'' stretching modes.8 The IR spectrum shows some weak
features in addition to the four intense absorption bands due to the cis-
W(CO)4[P(OCH3)3](η2-acfc). These weak absorption bands can be attributed to the
unreacted W(CO)5[P(OCH3)3] (only the band at 2079 cm-1 is observable, the others
are hidden under the strong absorptions), and W(CO)3[P(OCH3)3]2(η2-acfc) (2001
and 1891 cm-1, the third one is hidden under the strong absorptions).
W(CO)3[P(OCH3)3]2(η2-acfc) complex was also monitored by mass spectrometry.
Molecular weight: 756.1 g/mol
Figure 4.14. IR spectrum of W(CO)4[P(OCH3)3](η2-acfc) in n- hexane
40
-
The 1H-NMR spectrum of cis-W(CO)4[P(OCH3)3]( η2-acfc) taken in CD2Cl2 solution (Figure 4.15) shows one doublet at 3.68 ppm with a 31P-1H coupling
constant of 14 Hz for the P(OCH3)3 ligand, four signals at 4.92, 4.59, 4.55 and 4.18
ppm for the ferrocenyl moiety and three multiplets centered at about 4.78, 4.51, and
3.56 ppm for the olefinic protons of acryloylferrocene ligand. The multiplets of the
olefinic protons are further complicated by the 31P-1H coupling and therefore difficult
to analyze. Compared to the free acryloylferrocene molecule, the signal of olefinic
protons show a remarkable coordination shift ∆δ=1.91 ppm, 1.88 ppm and 2.1 ppm,
respectively, indicating the coordination of acryloylferrocene through the C=C bond.
13C-NMR spectrum of the W(CO)4[P(OCH3)3](η2-acfc) complex was taken
(Figure 4.16.) in CD2Cl2 solution. The spectrum exhibits four doublets and one
singlet for the cis-W(CO)4[P(OCH3)3](η2-acfc) in carbonyl region. The singlet at
198.06 ppm can readily be assigned to the carbonyl carbon of the acryloylferrocene
ligand. The four doublets are due to the four different CO ligands in cis-
W(CO)4[(P(OCH3)3](η2-acfc) (Figure 4.17). Because of 31P-13C coupling, all of the
four carbonyl signals are of doublet structure. The doublet at the highest chemical
shift of 207.26 ppm with J(31P-13C)= 16.4 Hz is assigned to the CO ligand trans to
the acryloylferrocene ligand. The doublet at 204.5 ppm with the largest 31P-13C
coupling constant of 27.3 Hz is assigned to the CO ligand trans to the
trimethylphosphite. The other two doublets at 197.37 and 196.97 ppm with 31P-13C
coupling constant of 11 and 10.9 Hz, respectively, are assigned to the CO ligands
trans to each other (cis to both acfc and P(OCH3)3 ligands). There exists two
additional doublets at 199.9 and 195.54 ppm with 31P-13C coupling of 12.9 Hz and
9.1 Hz, respectively. By comparison with the literature values,33 these can readily be
attributed to the W(CO)5[(POCH3)3] complex, which remains unreacted as seen also
in IR and mass spectra. The doublet at 52.85 ppm with the 31P-13C coupling constant
of 6 Hz is due to the methyl carbons of the trimethylphosphite ligand. The weak
doublet at 52.40 ppm with J(31P-13C)= 10.9 Hz can be attributed to the methyl
carbons of the trimethylphosphite ligand of the W(CO)5[(POCH3)3] complex which
remains unreacted in small amount. The olefinic carbon atoms give two signals at
41
-
69.03 and 62.49 ppm which have been shifted by ∆δ = 64.4 and 64.2 ppm,
respectively, compared to the free acryloylferrocene molecule.
In the mass spectrum of the complex (Figure 4.18.), the observed and the
calculated values of the molecular peak are in accordance. The formation of the
W(CO)4[P(OCH3)3](η2-acfc) complex can be concluded from mass spectrum as well
as 13C-NMR and 1H-NMR spectra. Mass spectrum also shows the existence of the
W(CO)3[P(OCH3)3]2(η2-acfc) complex with the molecular weight of 756.1 g/mol
and W(CO)4[P(OCH3)3]2 with the molecular weight of 543.8 g/mol (Figure 4.19).
42
-
Fig
ure
4.15
. 1H
-NM
R sp
ectru
m o
f cis
-W(C
O) 4
[P(O
CH
3)3]
(η2 -
acfc
) tak
en in
CD
2Cl 2
solu
tion
43
-
F
igur
e 4.
16. 1
3 C-N
MR
spec
trum
of c
is-W
(CO
) 4[P
(OC
H3)
3](η
2 -ac
fc) t
aken
in C
D2C
l 2so
lutio
n
44
-
Fig
ure
4.17
. CO
regi
on o
f 13 C
-NM
R sp
ectru
m o
f cis
-W(C
O) 4
[P(O
CH
3)3]
(η2 -
acfc
) tak
en in
CD
2Cl 2
solu
tion
45
-
Figure 4.18. Mass spectrum of cis-W(CO)4[P(OCH3)3](η2-acfc): Molecular peak of
cis-W(CO)4[P(OCH3)3](η2-acfc) complex, observed (top) and calculated (bottom).
46
-
Figure 4.19. Mass spectrum of cis-W(CO)4[P(OCH3)3](η2-acfc)
47
-
CHAPTER 5
CONCLUSION
UV irradiation of hexacarbonyltungsten(0), W(CO)6, in n-hexane solution in
the presence of acryloylferrocene, acfc, gives the pentacarbonylacryloyl-
ferrocenetungsten(0) complex, W(CO)5(η2-acfc), as the sole product of
photosubstitution reaction.
WOC
OC CO
CO
CO FeO
Figure 5.1. W(CO)5(η2-acfc)
Different from the general scheme of sequential photosubstitution of
hexacarbonylmetal(0) with olefin,16 photolysis of W(CO)6 in the presence of
acryloylferrocene gives only the monosubstitution product, W(CO)5(η2-acfc).
Prolonged irradiation doesn’t give any further CO substitution reaction, contrarily it
results in backward reaction of the product, W(CO)5(η2-acfc) complex, to
decompose into hexacarbonyltungsten(0) complex and free acryloylferrocene. The
formation of the complex was monitored by FT-IR spectroscopy. After the reaction
48
-
was completed, the resulting complex was isolated and characterized by the
techniques of IR, Raman, NMR spectroscopy and mass Spectrometry and elemental
analysis. The W(CO)5(η2-acfc) complex was found not to be stable in solution and
decomposed into hexacarbonyltungsten(0) complex and free acryloylferrocene.
In order to stabilize the tungsten-olefin bond with the acryloylferrocene, a
donor ligand was introduced into the complex. For this purpose, trimethylphosphite
was used as donor ligand and a tungsten carbonyl complex containing a donor ligand
and an olefinic ligand was designed. Starting with W(CO)6, W(CO)4[P(OCH3)3](η2-
acfc) was synthesized and characterized by IR, NMR spectroscopies and mass
spectrometry. This complex was shown to have a cis arrangement of the W(CO)4
unit in the octahedral W(CO)4[P(OCH3)3](η2-acfc) molecule. The 13C-NMR
spectrum shows that all of the four carbonyl ligands are different. The
W(CO)4[P(OCH3)3](η2-acfc) was found to be even less stable than W(CO)5(η2-acfc).
Thus, introducing a donor ligand into the molecule doesn’t provide additional
stability for the tungsten-olefin bond in the case of acryloylferrocene.
In general, the metal-carbonyl complexes of acryloylferrocene are not stable.
Attempts to prepare the chromium and molybdenum analogs failed, presumably
because of the instability of the metal-olefin bond. Together with the large
coordination shifts of olefinic carbon and proton signals in both complexes
W(CO)5(η2-acfc) and W(CO)4[P(OCH3)3](η2-acfc), this instability may be
considered as an indication for the activation of the acryloylferrocene C=C bond
upon coordination to a transition metal.
49
-
REFERENCES
[1] Bochman M.; Organometallics 1-Complexes with Transition Metal-Carbon σ-
bonds; Oxford University Press, Oxford , 1994
[2] Zeise, W.C; Ann. Phys. (Leipzig) (2) 9 (1827) 632
[3] Wilkinson G., Rosenblum M., Whiting M.C., Woodward R.B.; JACS , 74 (1952)
2125
[4] Heck, R.F.; Organotransition Metal Chemistry A Mechanistic Approach ;
Academic Press, New York and London, 1974
[5] Pruchnik, F.P.; Organometallic Chemistry of the Transition Elements ; Plenum
Press, New York and London, 1990
[6] Tsutsui, M., Morris, N.L., Nakamura, A., Ichikawa, M., Mori, K.; Introduction to
Metal π-Complex Chemistry ; Plenum Press, New York-London , 1970
[7] Elschenbroich, C., Salzer A.; Organometallics A Concise Introduction ; VCH
Publishers, Inc., 1992
[8] Bratermann, P.S.; Metal Carbonyl Spectra; Academic Press, Lomdon, New York,
San Francisco, 1975
[9] Jones, L.H.; Advances in the Chemistry of the Coordination Compounds ;
Macmillan, New York, 1961
50
-
[10] Cotton, F. A.; Modern Coordination Chemistry, Interscience, New York, 1960
[11] Mond, L., Langer C., Quincke, F.; J. Chem. Soc. (1980) 749
[12] Wender, I., Pino, P.; Organic Synthesis via Metal Carbonyls, Vol. 1 ;
Interscience, New York, 1968
[13] Huheey, J.E., Keiter, E.A., Keiter, R.L.; Inorganic Chemistry Principles and
Structure and Reactivity; 4th Edition, Harper Collins College Publishers, New York,
1993
[14] Strohmeier, W., Von Hobe D.; Chem. Ber., 94, 1964, 761; Nasielski J., Colas,
A.; Inorg. Chem. 17 (1978) 237
[15] Strohmeier W.; Angew. Chem., 76 (1964) 873; Angew. Chem., Int., Ed., Engl., 3,
(1964) 730; Koerner, G.E., Grewels, F.W.; Top. Curr. Chem., 13 (1969) 366;
Geoffroy, G.L., Wrighton, M.S.; Organometallic Photochemistry; Academic Press,
New York, 1979
[16] Grevels, F.W., Jacke, J., Klotzbücher, W.E., Mark, F., Skibbe, V., Schaffner, K.,
Özkar S.; Organometallics, 18 (1999) 3278
[17] Gmelin Handbook of Inorganic and Organometallic Chemistry, Fe Organic
Compounds, 8th ed., vol. A10, Springer, Berlin, 1991
[18] Togni, A.; Hayashi, T.; “Ferrocenes: Homogeneous Catalysis, Organic
Synthesis, Materials Science”, VCH, Weinheim, 1995
[19] Bear, P.D., Smith, D.K.; Prog. Inorg. Chem., 46 (1997) 1
51
-
[20] Miller, J.S., Epstein, A.J.; Angew. Chem. Int. Ed. Engl, 34 (1994) 385
[21] Long, N.J.; Angew. Chem. Int. Ed. Engl., 35 (1995) 21
[22] Coles, H.J., Meyer, S., Lehmann, P., Deschenaux, R., Juaslin, I.; J. Mater.
Chem., 9 (1999) 1085
[23] Astruc, D.; New. J. Chem., 16 (1992) 305
[24] Özkar, S., Kayran, C., Demir, N.; J. Organomet. Chem. ; 688 (2003) 62
[25] Doğan, Ö., Şenol, V., Zeytinci, S., Koyuncu, H., Bulut, A.; J. Organomet.
Chem., 691 (2005) 430
[26] Grevels, F.W., Jacke, J., Özkar, S., Saldamlı, S.; Organometallics, 24 (2005)
4613
[27] Shriver D.F., Atkins P.W., Langford S.H.; Inorganic Chemistry 2nd edition;
Oxford University Press , Oxford , 1994
[28] Özkar, S., Tunalı, N.K. ; Anorganik Kimya, Gazi Üniversitesi, yayın no: 185,
Ankara, 1993
[29] Templeton, J.L.; Advanced Organometallic Chemistry, Four-Electron Alkyne
Ligands in Molybdenum(II) and Tungsten(II) Complexes, Academic Press Inc., 29
(1989) 1-100
[30] King, R.B., Eisch, J.; Organometallic Syntheses, Transition Metal Compounds,
(1965) 1
52
-
[31] Mathieu, R., Lenzi, M., Poilblanc, R. ; Inorg. Chem. 9 (1970) 2030
[32] Bodner, G. M., Inorg. Chem., 14 (1975) 2694
[33] Braterman, P.S., Milne, D.W., Randall, E.W., Rosenberg, E.; J. C. S. Dalton,
(1973) 1027
53