Download - Spectrum 54
COVER STORY: FEV CONDITIONS DIESEL ENGINES FOR THE UPCOMING "REAL DRIVING EMISSIONS PROCEDURES"
ISSUE 54 FEV CUSTOMER MAGAZINE
NVHHolistic approach for engine
speed irregularity and NVH
FEV ePGS
FEV & D2T
Package-optimized hybrid drive
Prof. Pischinger explains the acquisition
GREENREX Gas-fueled
Range Extender
EDITORIAL
2
Dear readersThis issue of our FEV customer magazine SPECTRUM deals with sustainability:
In the coming years, further minimiz-ing vehicle emissions will be one of the most important development drivers. The increasingly stringent emission regulations require con-tinuous optimizations that must be validated in new test cycles. The introduction of "Real Driving Emissions" drive cycle in Europe is intended to achieve more realistic results.
In this issue of SPECTRUM, we intro-duce you to a sustainable solution to addressing this highly dynamic mea-surement cycle with conventional diesel engines. Alternative solutions, such as plug-in hybrid drive trains or the use of a Range Extender can make an important contribution – especially in the context of the fleet fuel consumption targets. Therefore, within a government-sponsored project called "GreenRex" FEV has been devoted to the development of a gas-powered Range Extender
for commercial vehicles and our ePGS is an ultra-compact hybrid drive solution.
Our desire for sustainable develop-ment is also reflected in the estab-lishment of the FEV Group Holding GmbH. Both this restructuring and the associated increase in staffing levels as well as the acquisition of the test systems and engineering service provider D2T enable us to respond faster in the future to customer specific requirements. In addition, our product portfolio and our international capabilities have been significantly enhanced.
Finally, we have also reorganized our customer magazine. This issue of SPECTRUM offers a new layout and a new editorial concept.
I hope this issue of SPECTRUM offers you some interesting insights.
Prof. Stefan Pischinger, President & CEO of FEV Group Holding GmbH
TABLE OF CONTENTS
3
FEV‘s emission based EGR control p. 08
Extended vehicle functions by targeted cloud integration p. 04
FEV ePGS: Package-optimized hybrid drive p. 10
01 RESEARCH AND DEVELOPMENT
02 WORLD OF FEV
14Customer-oriented restructuring: FEV Group and its faces 16FEV & D2T: Prof. Pischinger
explains the acquisition
04Extended vehicle functions by targeted cloud integration
08FEV‘s emission based EGR control
12GREENREX: Development of a gas-fueled Range Extender
10FEV ePGS: Package-optimized hybrid drive
06Holistic approach for engine speed irregularity and NVH
TITLE
PROJECT OSCAR01 RESEARCH AND DEVELOPMENTPROJECT OSCAR
4 5
IMPORTANT STEP ON THE WAY TO A FULLY CONNECTED VEHICLE
CONNECTED MOBILITY: PROJECT OSCAR
Adding functionality through apps, optimizing workshop services, and creating range forecasts for electric vehicles: Use of a vehicle as a mobile sensor and multimedia platform is no longer a vision of the future. Today there are a number of projects in which networked vehicles collect data on driving, traffic and environmental conditions and share and make that data available via Car2Car and Car2X communication. In a joint project, named OSCAR (Open Service Cloud for the Smart Car) FEV is cooperating with leading research and development partners in developing modular information and communication technology structures to integrate FEV and StreetScooter provided vehicles into a cloud.
Written by:Prof. Günter Feyerl
Contact:Andrea Conti
WITH ONLY ONE VEHICLE, A WIDE VARIETY OF DIFFERENT OEM VEHICLES CAN BE SIMULATED
FEV EXPANDS VEHICLE FUNCTIONS WITH TARGETED CLOUD INTEGRATION IN THE JOINT PROJECT OSCAR
Fundamentals of the project
The goal of the OSCAR project is to integrate the electric vehicle into a cloud structure by building a modular information struc-ture and communication technology (ICT). FEV's iCU (intelligent Connection Unit) development platform is integrated into the vehicle and has access to the data stream of the vehicle's onboard network. The data collected via CAN bus and a GPS system can be sent to the cloud via a UMTS interface from the vehicle. In addition, they can be received again by the sending vehicle or other connected vehicles after a service-oriented analysis in the cloud. This creates a bi-directional communication path.
Development with sustainable utilization potential
Data formats can be adapted to various project and server re-quirements via the iCU, representing an excellent foundation for future volume production development. With only one vehicle, a wide variety of different OEM vehicles can be simulated or, alternatively, the data formats of var-ious vehicles can be translated into the same cloud data structure. The cloud vehicle connection allows for other future services such as the installation of specific vehicle apps or the use of conventional apps for mobile devices. This is made possible by the FEV-iCU. The data can be accessed on commercial smartphones or tab-lets directly in the vehicle via Bluetooth or local WLAN. To send the right data to the correct addresses in the cloud structure, an FEV-developed AES (Automotive Embedded Service) server collects the transmitting vehicle data and decides, according to defined filtering rules, which information from the vehicle should be forwarded to particular addresses.
>>With only one vehicle, a wide variety of different OEM vehicles can be simulated<<
"Within the framework of the OSCAR project, we developed a new, open and manufacturer-independent ICT architecture for electric vehicles and have intensively tested it in the Aachen region under real life scenarios," explains FEV’s Dr. Stefan Müller-Schneiders. The project partners also established a DIN Spec (91324), a data set for an open service cloud, which can be used for OEM and third party services.
Important data for drivers...
Vehicle users can retrieve current vehicle data, as well as statistical information on their own usage history, through the effective combination of cloud data and apps that are operated via the vehicle display (HMI). As a result drivers can, for example, plan their route continuously, based on traffic information, the reach area and on the altitude. In addition to real time data such as battery state and energy consumption of various systems, data comparison with the cloud data allows optimization of one's own driving behavior. Driving profile and fuel consumption for different drivers can be compared and optimization potentials can be identified.
... and fleet operators
Fleet operators will particularly benefit from improved diagnos-tic capabilities on their electric vehicles: The operator not only gains insight into vehicle parameters such as position, operating condition and battery or charging state; even error codes can be read via the cloud. Safe and limited access to such sensitive data improves the coordination options for maintenance schedules and allows for preliminary diagnosis by authorized parties.
INFOThe project OSCAR, which is subsidized by the Ger-man Federal Ministry of Economics and Technology, is led by a consortium of FEV GmbH, Forschungs-institut für Rationalisierung (FIR) e. V. - RWTH Aa-chen, Fritz Dräxlmaier GmbH & Co. KG, Hans Hess Autoteile GmbH, QSC AG, regio iT gesellschaft für informationstechnologie mbH, SE Software En-gineering – Technical University of Aachen and StreetScooter GmbH. The advisory board consists of leading OEMs and suppliers, e. g. Continental AG, PSI AG, Kirchhoff Automotive, TRW Automotive and the German Aerospace Centre (DLR).
The car as a mobile sensor and multimedia platform: FEV and its development partners have created a cloud structure for vehicles within the government subsidized project OSCAR that allows drivers and fleet operators to gain access to important planning data and additional functions.
NVH01 RESEARCH AND DEVELOPMENTNVH
6 7
ECONOMICAL, SMALL BUT NOISY? – THAT IS NOT MANDATORY
Engine developers and OEMs have mastered the small engine - less displacement, fewer cylinders, yet maintaining driving pleasure. Today, 4-cylinder engines are even commonplace in the luxury segment. Established measures – like fewer cylinders, higher cylinder pressure and early clutch lock-up – increase the speed irregularity in the lower engine speed range. The connected drivetrain is increasingly susceptible to vibration. So, to keep or even improve the expected driving pleasure, influencing parameters must be analyzed early in the concept phase of drivetrain development, and counter measures must be evaluated to reduce interior noise.
NOISE VIBRATION HARSHNESS
To achieve this, FEV developed a method to support drivetrain development from concept up to the start of production. The key component of this method is multi-body simulation of the drivetrain using FEV’s "Virtual Engine" software. The simulation result is either directly evaluated within the software, or serves as input for a subsequent Vehicle Interior Noise Simulation with "FEV VINS", which combines the simulated excitations with the vehicle body transfer functions of the corresponding noise path.
As complex as necessary, as simple as possible
The complexity of the interior noise simulation can be var-ied depending on the existing input data and the target. This ranges from a pure simulation of the structure-borne noise with smoothed standard transfer functions, to the calculation of a more realistic interior noise using vehicle specific transfer functions, including combining measured airborne noise shares. Also the complexity of the multi-body simulation can meet the requirements of the development process. In the concept phase, where only basic input data are available and very different configurations need to be quickly evaluated, a pure torsional vibration model can be set up. In the further course of the de-velopment process the model is extended to a full 3-D model by adding different sub-systems like wheel suspension.
Written by:Klaus Wolff
Dr. Georg [email protected]
Dr.-Ing. Christoph [email protected]
Contact:Frank Ehrlich
Specific results
As an example, the illustration shows Campbell diagrams of the interior noise for a full load run up. Here the simulated interior noise (right) can be compared to the measured noise (left), because vehicle specific transfer functions have been used. In contrast to the measured noise the simulated noise only in-cludes the noise shares caused by the drive train. The comparison shows that these are dominant in this vehicle below 100 Hz,
especially for the ignition order. The measurement also includes non-rota-tory excited noise shares. E.g. the high level of the fourth engine order at 100 Hz can be traced
back to the orifice noise of the exhaust system. Due to the shown variation possibilities of the simulation depth from pure torsional vibration models up to the calculation of realistic interior noise, the presented method can be effectively applied at all stages of the development process.
FEV's HOLISTIC APPROACH FOR ENGINE SPEED IRREGULARITY AND NVH
Measured interior noise (left) and simulated noise share due to rotatory excitation (right), full load run-up, 6th gear
BY VARIATION OF SIMULATION COMPLEXITY THE FEV METHOD CAN BE EFFECTIVELY APPLIED AT ALL STAGES OF THE DEVELOPMENT PROCESS
DIESEL EGR CONCEPTS01 RESEARCH AND DEVELOPMENTDIESEL EGR CONCEPTS
8 9
PARADIGM SHIFT IN EMISSION TESTING
Emission testing shall reflect real driving conditions more precisely: This Is the European commission’s aim in di scussing the RDE (Real Driving Emissions) test procedure included in the upcoming Euro 6c emissions legi slation. The new test procedures will cover a wider range of engine speed, engine load and ambient conditions. As a result, limiting the design and calibration of emission reduction systems to a reduced emission-relevant range is no longer sufficient to fulfill the legislative requirements. "More complex emission control systems, including EGR systems with several EGR circuits and coolers will become increasingly common", explains Dr. Thorsten Schnorbus, Deputy Department Manager for Diesel Engine Predevelopment at FEV GmbH. "A fast and robust control system that is easy to calibrate will become increasingly important in this context."
DIESEL EGR CONCEPTS
Advantages of FEV’s model-based approach
For this purpose, FEV has developed an innovative, model- based approach for direct emission-based EGR control in diesel engines. This approach shows that, given the more stringent requirements, a high potential exists for improvements with regard to engine-out emission as well as tail pipe emission behavior. The concept involves less calibration effort compared to current EGR approaches. In parallel, the full fuel consumption reduction potential of the engine can be utilized as a result of the flexible definition of the EGR fraction.
Neutralize ambient influences effectively
Changes in environmental or operating conditions are com-pensated by physical-based system reactions, such as EGR redistribution and/or EGR cooler bypass control. As a result, NOx emissions as well as fuel consumption stay very constant when there are major changes in ambient temperature. Also the intake manifold temperature can be kept at a very similar level, which is expected to have a positive effect on engine-out
HC and CO emissions. The similar intake manifold temperature level leads to a very stable exhaust gas temperature keeping the aftertreatment conversion efficiency consistent.
Functional principle of the EGR control
The air path control concept is based on an integrated NOx model from which a set point is derived for the target oxygen concen-tration in the cylinder (at "intake valve closure"). To compensate for the influence of modified boundary conditions on the NOx
emissions or to actively use the degrees of freedom of the EGR control, the specified value of the NOx engine-out set point
can be adjusted inde-pendently and adapted by algorithms taking into account the current con-version rate of the NOx
aftertreatment. To distribute the amount of EGR required to achieve the desired oxygen concentration in the cylinder, dedicated set points are defined for the oxygen concentration at each mixing point. Each set point can be controlled on the basis of different parameters. Since the entire air system is represented by dedicated physical models, it is also possible to determine the current oxygen con-centration at every mixing point. Under highly transient operating conditions, faster EGR paths can be used to compensate slower EGR paths by means of dynamic control intervention, so that
the desired specified oxygen con-centration in the cylinder is achieved even during highly dynamic cycles.
Written by:Joschka Schaub
A FAST AND ROBUST EGR CONTROL SYSTEM THAT IS EASY TO CALIBRATE WILL BECOME INCREASINGLY IMPORTANT
FEV’s EMISSION-BASED EGR CONTROL CONDITIONS DIESEL ENGINES FOR THE UP-COMING "REAL DRIVING EMISSIONS PROCEDURES"
HP EGR Control
Internal EGRControl
Set pointconversion/Limitation
ExhaustCamPosition
LP-EGR
HP-EGR
Intake Throttle Position
HP EGR ValvePosition
HP EGR CoolerBypass Valve
Exhaust ThrottlePosition
LP EGR ValvePosition
Inverted NOxModel
NOx EngineOut Target
NOx, Sensor
NOx, des
NOx, des: NOx concentration set pointO2,cyl,des: Oxygen concentration set pointO2,int,des: Intake oxygen concentration set pointO2,LPEGR,des: LP EGR oxygen concentration set point
NOxSensor Adaption
LP EGR Control
O2,Cyl,des
O2,Int,des
O2,Int
O2,LPEGR,des
O2,LPEGR
External/Internal EGR Split
External EGR Split
NOx-based EGR control with multi-loop EGR
01 RESEARCH AND DEVELOPMENT
10 11
SIZE MATTERS
HYBRIDIZATION OF POWERTRAINS
In contrast to full hybrids the main advantage of the plug-in hybrid is the possibility to drive longer distances even with higher velocity purely in electric drive mode. This however requires a higher electric performance of the electric machine of 70 to 100 kW under real operating conditions.
Especially with vehicles featuring a transversely mounted engine, the higher performance of the hybrid drive – including E-motor, clutch and damper – requires additional installation space.
Common Hybridization concepts
One common hybrid topolo-gy is the so-called P2 hybrid. Here the traction machine is positioned coaxially between the combustion engine and the transmission input and can be separated from the combustion engine via a clutch for pure electric driving. The Volkswagen Golf GTE or the Audio A3 e-tron, respec-tively, represent one option to keep the total installation length of engine, electric machine and transmission in a P2 concept constant. In these vehicles the electric engine is fully integrated into the transmission which was reduced by one gear. Another option is the layout of the electric machine axially parallel to the gear shaft. This layout allows for a neutral length, but requires an additional transmission unit in form of a gear set or a chain between gearbox input shaft and electric engine.
In almost all vehicle segments, electrification of the powertrain is necessary to reach the fleet consumption th-resholds. At the same time, due to the relatively low energy density of the battery, the introduction of pure electric vehicles has been less dynamic than it was hoped for. In particular plug-in hybrids contribute significantly to the anticipated reductions as the CO2 emissions are determined by the electric range alone or the battery size, respecti-vely. However, plug-in hybrid powertrains demand a massive intervention into the construction of the transmission which generates additional cost for relatively small production volumes. The manufacturers are therefore called to develop concepts which can be combined with various transmissions in a modular manner and have sufficient performance for various vehicle classes. One concept to solve this conflict is the compact ePGS module, developed by FEV.
FEV ePGS: compact and suitable for daily use
FEV has developed a compact alternative in the form of the ePGS, which can be combined with all common transmission variants. However, the combination with an automatic transmission is the most appropriate solution. Here the converter can be eliminated completely which allows for installation space for the ePGS module. Due to the excellent controllability of the electric motor a comparable comfort can still be achieved during take-off. Since the electric motor runs in generator mode during the take-off procedure, an additional start-up element is not necessary. At the re-start of the combustion engine from the EV mode the ePGS
uses the inertia of the electric machine in addition. The electric machine is decelerated with the closing of the clutch, and the combustion engine will be accelerated directly to synchronous speed. This happens almost jolt-free when the electric machine is adequately controlled. Also, no torque reserve has to be kept for the re-start of the combustion engine in the electric machine, so that the total available performance of the electric motor can be used in the EV mode. This fact reduces the installation length of the drive as well because the machine requires up to 10 kW less performance than a P2 concept with identical driving
performance in the EV mode.The suitability for daily use of the ePGS has been demon-strated with several prototypes and within a series pro-duction development project. Depending on the hybrid topology and the battery size, the CO2 emissions can be reduced by 15-50 percent.
Written by:Jürgen Ogrzewalla
MANUFACTURERS ARE CALLED TO DEVELOP PLUG-IN CONCEPTS WHICH CAN BE COMBINED WITH VARIOUS TRANSMISSIONS IN A MODULAR MANNER
FEVs PACKAGE-OPTIMIZED EPGS HYBRID DRIVE
Idle & StartTrans
Lock
Engine E-Motor
Parallel DriveTrans
Clutch C1
Engine E-Motor
Regenerative braking
TransEngine E-Motor
Electric drive(with one-way-clutch, OWC)
TransEngineOWC
E-Motor
ICE restart from E-drive
TransEngineOWC
E-Motor
Clutch C1
Driving modes of the ePGS drive in the Lever diagram
HYBRIDIZATIONHYBRIDIZATION
PROJECT GREEN REX01 RESEARCH AND DEVELOPMENTPROJECT GREEN REX
12 13
ALTERNATIVE FUELS: PROJECT GREEN REX
NATURAL GAS ENGINES THAT MEET THE REQUIREMENTS FOR A RANGE EXTENDER ARE CURRENTLY NOT AVAILABLEMARKUS KREMER TALKS ABOUT THE COLLABORATIVE "GREEN REX" PROJECT
Mr. Kremer, could you please explain the advantages of a range extender?
Range extenders are a central concept for vehicle electrification because they offset the disadvantage of the low energy density of traction batteries. In the case of a near-empty traction battery, the com-bustion engine supplies it with electrical energy via a driven generator.
The majority of existing range extenders consist of petrol SI engines. Why?
This is usually due to cost-efficient man-ufacturing. The obvious disadvantage of this concept is that the range extender is dependent on a fuel supply from crude oil. Natural gas engines that meet the requirements of a range extender – in-
INFOThe Green Rex projectThe Green Rex project is funded by the German Federal Ministry of Economics and Technology while the Deutsche Zentrum für Luft- und Raumfahrt (DLR) is the project executing organization. Green Rex was initiated by the State Agency for Electric Mobility and Fuel Cell technology Baden-Würt-temberg GmbH (e-mobil BW) and is listed in the German cluster "Electric mobility South-West". Partners include: KSPG AG, StreetScooter GmbH, the Institute for Internal Combustion Engines (VKA) at the RWTH Aachen, Fraunhofer ICT and KIT (wbk Institute for Production Technology).
cluding low production cost, compact size and good NVH attributes – are currently not available. This is why we are trying to determine, in the Green Rex project, if a marketable vehicle that is complete-ly operated with renewable energy can be manufactured through a new com-bination of available mass production technologies.
Why did you decide for the CNG instead of LPG technology?
We decided in favor of biogas instead of Liquefied Petroleum Gas (LPG) as the latter is not produced sustainably. Biogas offers greater potential for reduced emissions of harmful CO2. There is a potential of around
24 percent, which is similar to gasoline engines, and, even in comparison with LPG, savings of up to 15 percent are still possible. Finally, methane can be stored easily in the natural gas network.
What is the roadmap of the project?
In a first step, the petrol-fueled range ex-tender developed by FEV and KSPG was integrated into a StreetScooter commer-cial vehicle (model "Work") and present-ed to the public at the IAA Commercial Vehicles exhibition in Hannover. At the moment, the V2 KSPG range extender is
being revised and optimized for operation with processed biogas by the Fraunhofer Institute in Karlsruhe, Germany, in close cooperation with FEV GmbH. The revised range extender will then be thoroughly checked on the test bench and subse-quently integrated in another Street-Scooter Work commercial vehicle.
What results can be expected upon completion of this project?
Due to the early involvement of produc-tion specialists, we expect, by the end of the project, to be able to accurately estimate the additional cost of the biogas version in comparison to the base variant. The project includes MOT approval, initial
driving tests to document the CO2 savings for demonstration purposes, and illustra-tion of the concept feasibility. Differential Dynamic Programming is being used to develop an optimized operating strategy for delivery vehicles. This strategy will be utilized in FEV’s range extender control system to further decrease fuel consump-tion of the delivery vehicle.
Interviewpartner:Markus Kremer
1
2
35
Development of a light commercial vehicle that is operated purely with renewable energy is the goal of the collaborative project called "Green Rex". Experts from FEV GmbH, and a group of renowned partners, are revising a "range extender" for operation with compressed natural gas. The basis of
this development is the V2 range extender with the FEVCom© system developed by FEV and KSPG, which has already been operated in a Fiat 500 e-car from FEV's e-car fleet since 2012. FEV project leader Markus Kremer talked with SPECTRUM about the project, its tasks and roadmap.
METHANE COMPLIMENTS CONVENTIONALLY GENERATED ENERGY SOURCES IN AN IDEAL WAY
4
14 15
Prof. Dr.-Ing. Stefan Pischinger, President & CEO of FEV Group Holding GmbH
The Chairman of the Board and Managing Partner of FEV Group Holding GmbH is also Director of the Institute for Combustion Engines (VKA) at the RWTH Aachen and combines in both roles research and develop-ment in science and industry.
Dr.-Ing. Ralf Marquard, COO of FEV Group Holding GmbH
The previous Head of Research and Development at Deutz AG has been announced Chief Operating Officer in the management of FEV Group Holding GmbH in January 2015
Jürgen Grimm, Group Vice President SI Engines
Has joined FEV from the Hyundai Europe Technical Center, where he has worked as Head of Development for Diesel, SI engines and Transmis-sion for Europe since 2010
Dr.-Ing. Peter Heuser, Group Vice President Commercial, Industrial and Large Engines
Has established the FEV sin-gle-cylinder engine family as a universal development plat-form and has taken over global responsibility in 2014
Sami Sagur, CFO of FEV Group Holding GmbH
Has the dual role of being respon-sible for the finances of FEV Group as well as FEV GmbH
Dr.-Ing. Martin Pischinger, Group Vice President Research & Innovation Strengthens the technological leadership of FEV through sus-tainable research and innovation worldwide
Dr.-Ing. Ingo Steinberg Group Vice President Transmission Systems Offers extensive experience in the series production of automatic and manual transmissions and heads the global activities of BU Transmission systems since 2014
Rainer Paulsen, Group Vice Pres-ident Electronics and Electrifica-
tions as well as Operations
Is responsible for FEV's activities asso-ciated with software, battery devel-
opment and electrification as well as the management and operation of the
worldwide FEV test centres.
Dr.-Ing. Albert Haas, Group Vice President Test Systems
The distinguished expert is re-sponsible for the global activities of the Business Unit Test Systems
Thomas Körfer, Group Vice President Diesel Engines
Has worked for FEV since 1991 and has led the Diesel business unit in Europe for four years
CUSTOMER-ORIENTED RESTRUCTURING
The success story of FEV began in a four-room apartment in the immedi-ate vicinity of the University of Aachen (RWTH). In 1978, a small group of ded-icated engineers, under the direction of Prof. Franz F. Pischinger began to translate research and theory into practice. Today, with over 3,800 em-ployees at more than 35 locations on four continents, the FEV stands for pioneering development work.
Globally operating strategic top structureThe demand from the automotive man-ufacturers and tier 1 suppliers is steadily increasing with the complexity of the development tasks and is, thus, an im-portant driver for the international growth of FEV. To meet this demand, FEV has strategically realigned by establishing the Group Holding GmbH in 2014. To better address the volume of international cus-tomer inquiries, our central business units have been given more responsibility for their operations. The new structure of our
WE REDEFINE DAILY WHAT IS TECHNICALLY FEASIBLE TO GUARANTEE SUSTAINABILITY. SUCH EFFORTS ALSO DO NOT STOP WITH THE STRUCTURE OF OUR OWN ENTERPRISE
international resources increases FEV’s efficiency, whereby the business units can focus more than ever on their respective functional areas of responsibility.
This is made possible, especially by the newly created global responsibilities in FEV Group Holding GmbH: Since Janu-ary 2015, business operations have been placed into the hands of Chief Operating Officer (COO) Dr. Ralf Marquard. At the same time, the divisions have received globally operating Group Vice Presidents who are responsible for optimizing devel-opment work across all of the continents. "There will be no change for our customers
as it relates to their daily dealings with their known counterparts at FEV," explains Professor Stefan Pischinger, President and CEO of FEV Group. "However, as a result of the restructuring, cross-national projects can now be executed even more efficiently, and our clients will notably profit from this difference."
FEV GROUP02 WORLD OF FEVFEV GROUP
17
Professor Pischinger, what were the reasons that motivated you to acquire D2T?
Following the expansion of our electronics and automotive en-gineering competence with the acquisition of DGE Inc. in 2013, we see this acquisition as an opportunity to significantly grow our engineering capacities internationally. D2T not only offers products and services which fit seamlessly into our portfolio, we will also benefit from the D2T subsidiaries around the world on our course of continued global expansion. With the acqui-sition, we expand our engineering capacities to face growing demand from the various operating regions. The important thing is: we will maintain and expand the strong D2T brand. The D2T locations will be strengthened and expanded in the future through investment.
Keyword customer needs: Can you summarize briefly the customer benefits?
Both FEV and D2T offer expertise gained through decades of developing powertrain solutions. By joining forces we extend their individual strengths and offer a larger pool of global re-sources. As a result we offer development services close to our customers around the globe and are in a position to offer solu-tions according to specific regional or international standards. In addition, large transnational projects can now be handled more efficiently.
"FEV has already demonstrated its expertise in the development and use of diverse powertrain technologies. We are delighted that D2T has found in FEV a strong, innovative partner with its own global network and renowned clients," commented Eric Lafargue, IFP Investissement’s CEO during the signing ceremony. With this step, FEV focuses on international customers and their demands which will be serviced even more comprehensively in the future. In this issue of SPECTRUM Professor Pischinger talks about the takeover’s impact on the engineering business of both companies and about customer benefits.
1
FEV & D2T
MORE THAN THE SUM OF THE PARTSFEV EXTENDS ITS GLOBAL ENGINEERING CAPACITY WITH ACQUISITION OF D2T S.A.
02 WORLD OF FEVFEV ACQUIRES D2T FEV ACQUIRES D2T
2
FEV GmbH has acquired the French test systems and engineering service provider D2T Powertrain Engineering S.A. This action was completed with a signing ceremony on March 24, 2015. FEV GmbH takes over the business of D2T in France, its subsidiaries in Germany, China, the U.S. and interests in South Korea and Japan.Through this strategic expansion, FEV, a leading provider of engineering services for powertrain and vehicle tech-nologies, significantly expands its global expertise and capacities in the test systems business area, in particular.
18
Most likely, the changes will be most severe in France, the home country of D2T?
Yes, as a matter of fact. Our acquisition of D2T will give the com-bination of D2T's and FEV’s activities in the French market and our respective French locations a significant weight. With this step, FEV and D2T now become a leading provider of engineering services in the French market. Mr. Nadim Andraos, the former head of FEV France, has now taken over the responsibility for the combined D2T and FEV activities. In the future, we will focus on the sites in Trappes and Rouen, in which we have invested, as well as the representative offices on site at the French OEM’s.
To what extent does this affects your capacity and skills in France? Or in other words: How are D2T and FEV better together?
Even the basic figures already show the benefits: In Trappes near Paris and in Rouen, D2T is operating a total of 15 engine test benches, one chassis dynamometer and five battery test benches. Worldwide, D2T employs more than 450 people; 400 of them in France. Furthermore, our competencies are complementary, especially in France, where FEV has mainly offered turnkey test systems solutions in the past. D2T’s focus has been on simulation and testing. As a result, we will be in a position to offer this expanded range of services from one-
19
IMPRINT
UPCOMMING EVENTS
Spectrumissue 01/2015 (Number: 54)
RedaktionFEV GmbH
LayoutFEV GmbH
Has your address changed? Do you know a colleague who would also like to receive future issues of the SPECTRUM? Send the name of your company, person’s name, and complete mailing address via E-Mail to: [email protected]
READER SERVICE
INFOAbout D2T
D2T is headquartered in Trappes, France and employs more than 450 people worldwide. D2T’s customers include distinguished OEMs and suppliers of the automotive, commercial vehicle, marine and aviation industries, as well as oil companies and research and development institutions. Until the takeover by FEV, D2T was a 100 % affiliate to IFP Investissements.
About IFP Investissements
IFP Investissements is IFP Energies nouvelles industrial’s investment holding company. IFP Investissements supports the companies in their portfolio through every stage of their growth, supports innovation and creates new industrial subsidiaries.
stop. Wherever D2T and FEV are present with representation, we intend to build on the principle of "one face to the cus-tomer" in order to ensure clarity in terms of responsibilities and contact people.
How do you ensure continuity in the development work and high quality despite the changing bound-ary conditions?
The particular strengths of D2T and FEV lie in their global pres-ence, in their physical and contextual proximity to our customers and in the close cooperation with leading research institutions which enables us to channel the latest insights from science and research directly into our development projects. We will continue to build on this important and unique feature of both companies. For nearly four decades, FEV’s management has been very much interlinked with RWTH Aachen University. As part of IFP Energies nouvelles industrial, D2T incorporated re-search and development as well. In the future, we will continue to search for a cooperation with both of these institutions and, thus, optimize our development services with the latest research results and development as well.
3
4
5
FEV ACQUIRES D2T
SEPTEMBER
OCTOBER
NOVEMBER
DECEMBER
JUNE
16.06. - 17.06.2015
16.06. - 18.06.2015
International VDI Congress Drivetrain for Vehicles 2015
Testing Expo Stuttgart
Friedrichshafen, Germany
Stuttgart, Germany
09.09. - 10.09.2015
30.09. - 01.10.2015
LCV Cenex - Low Carbon Vehicle Event
17th MTZ Fachtagung VPC.plus "Simulation und Test für die Antriebsentwicklung"
Millbrook, UK
Hanau, Germany
05.10. - 07.10.2015
12.10. - 14.10.2015
20.10. - 21.10.2015
24th Aachen Colloquium "Automobile and Engine Tech-nology"
f-cell + BATTERY+STORAGE, International trade fair for battery and energy storage
8th MTZ-Fachtagung, "Ladungswechsel im Verbrennungsmotor"
Aachen, Germany
Stuttgart, Germany
Stuttgart, Germany
09.11. - 13.11.2015
24.11. - 25.11.2015
23.11. - 25.11.2015
Telematics Munich
"Heavy Duty On and Off-Highway Engines, 10th International MTZ Conference"
Aachen Acoustics Colloquium
Munich, Germany
Speyer, Germany
Aachen, Germany
07.12. - 10.12.2015 14th International CTI Symposium – Automotive Transmissions, HEV and EV Drives
Berlin, Germany
CONTACT
FEV GmbHNeuenhofstraße 18152078 AachenDeutschland
Phone +49 241 5689-0Fax +49 241 5689-119 [email protected]
FEV North America, Inc.4554 Glenmeade Lane Auburn Hills, MI 48326-1766 ∙ USA Phone +1 248 373-6000Fax +1 248 373-8084
FEV China Co., Ltd.No. 35 Xinda Street QixianlingHigh Tech Zone ∙ 116023 Dalian ∙ China Phone +86 411 8482-1688Fax +86 411 8482-1600
FEV India Pvt, Ltd.Technical Center IndiaA-21, Talegaon MIDCTal Maval District ∙ Pune-410 507 ∙ India Phone +91 2114 666 - 000 [email protected]
PASSION. INNOVATION. SOLUTIONS.