Download - Sony Bdp Bx57,s570
-
8/8/2019 Sony Bdp Bx57,s570
1/132
Sony CorporationHome Entertainment Business Group
SERVICE MANUAL
9-890-731-11
2010A6900-1
2010.01
Published by Design Engineering Dept.
BLU-RAY DISC/DVD PLAYER
Ver. 1.0 2010.01
BDP-BX57/S570RMT-B107A/B107P
SPECIFICATIONS
US Model
Canadian Model
AEP Model
UK Model
Australian/ New Zealand Model
SystemLaser: Semiconductor laser
Inputs and outputs(Jack name:
Jack type/Output level/Load impedance)LINE OUT R-AUDIO-L:
Phono jack/2 Vrms/10 kilohmsDIGITAL OUT (OPTICAL):
Optical output jack/18dBm (wave length 660nm)
DIGITAL OUT (COAXIAL):Phono jack/0.5 Vp-p/75 ohms
HDMI OUT:HDMI 19-pin standard connector
COMPONENT VIDEO OUT(Y, PB, P R) (US, CND):Phono jack/Y: 1.0 Vp-p/PB, PR: 0.7 Vp-p/75 ohms
(Y, PB/CB, P R/CR) (EC1, EC2, CEK, AUS):Phono jack/Y: 1.0 Vp-p/
PB/CB, PR/CR: 0.7 Vp-p/75 ohms
LINE OUT VIDEO:
Phono jack/1.0 Vp-p/75 ohms
LAN (100):100BASE-TX Terminal
EXT:External memory slot (For connecting the externalmemory)
DC output: 5 V 500 mA MaxUSB:
USB jack Type A (For connecting digital stillcamera and USB memory)
WirelessWireless LAN standard:
IEEE802.11a/b/g/n
Frequency range:US:
2.4 GHz band: Channels 1-115 GHz band: Channels 36-64, 100-140, 149-165CANADIAN:
2.4 GHz band: Channels 1-115 GHz band: Channels 36-64, 100-116, 132-140,149-165
AEP, UK:
2.4 GHz band: Channels 1-135 GHz band: Channels 36-64, 100-140AUSTRALIAN:
2.4 GHz band: Channels 1-135 GHz band: Channels 36-64, 100-116, 132-140,149-165
Modulation:DS-SS Modem and OFDM Modem
GeneralPower requirements:
120 V AC, 60 Hz (US, CND)220 240 V AC, 50/60Hz (AEP,UK, AUS)
Power consumption:
24 WDimensions (approx.):430 mm 219 mm 46mm(17 in. 85/8 in. 1 13/16 in.)(width/depth/height) incl. projecting parts
Mass (approx.):2.3 kg (5 lb 11/8 oz)
Operating temperature:5 C to 35 C (41 F to 95 F)
Operating humidity:25% to 80 %
Supplied accessories
Specifications and design are subject to change
without notice.
Audio/video cable (phono plug 3) (1)
AC power cord (1)
Remote commander (remote) (1)
Size AA (R6) batteries (2)
(US, CND, AUS)
BDP-BX57/S570
BDP-S570
Photo: BDP-S570
Remote : RMT-B107P
HDMI cable (1) (BDP-BX57: US)
NEW ZEALAND:
2.4 GHz band: Channels 1-135 GHz band: Channels 36-64, 100-140, 149-165
(BDP-BX57/S570 : US Only)
ENERGY STAR and the ENERGY STAR mark
are registered U.S. marks. ENERGY STAR is a
registered mark owned by the U.S. government.
-
8/8/2019 Sony Bdp Bx57,s570
2/132 2
BDP-BX57/S570
SAFETY CHECK-OUT
LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The limit indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of a
passive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
1. Check
thearea of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are pinchedor contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to
the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
5. Check the line cord for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
6. Check the B+ voltage to see it is at the values specified.
7. Check the antenna terminals, metal trim, metallized knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
1.5k0.15F
(0.75 V)
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
CAUTION:The use of optical instrument with this product will increase eye
hazard.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radia-
tion exposure.
This label is located on the laserprotective housing inside theenclosure.
WARNING!!WHEN SERVICING, DO NOT APPROACH THE LASEREXIT WITH THE EYE TOO CLOSELY. IN CASE IT ISNECESSARY TO CONFIRM LASER BEAM EMISSION,
EROMFOECNATSIDAMORFEVRESBOOTERUSEBTHAN 25 cm FROM THE SURFACE OF THE OBJEC-
TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 ENILDETTODROWITH MARK 0 NIDNASMARGAIDCITAMEHCSEHTNOTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION. RE-
ESOHWSTRAPYNOSHTIWSTNENOPMOCESEHTECALPROLAUNAMSIHTNINWOHSSARAEPPASREBMUNTRAP
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!
LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 ETSILALTESEUQITAMHCSSEMMARGAIDSELRUS
EDTIRUCSALRUOPSEUQITIRCTNOSSECIPSEDSTNASOPMOCSECRECALPMEREN.TNEMENNOITCNOFTNOSSORMUNSELTNODYNOSSECIPSEDRAPEUQ
DONNS DANS CE MANUEL OU DANS LES SUPPL-MENTS PUBLIS PAR SONY.
This appliance is classied as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the laser
protective housing inside the
enclosure. (AEP, UK, Australian
New Zealand)
-
8/8/2019 Sony Bdp Bx57,s570
3/132 3
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Disc Removal Procedure If The Tray Cannot Be
Ejected (Forced Ejection) ............................................. 1-1
1-2. Work when optical device are replaced ........................ 1-1
1-3. Test Disc ....................................................................... 1-2
1-3-1. Operation and Display ............................................. 1-2
1-4. Drive Repairing............................................................. 1-15
1-4-1. Preparation .............................................................. 1-15
1-4-2. Checking Flow ~ Drive (BU) section ~ .................... 1-15
1-4-3. BU Check Flow [zz] ~ .............................................. 1-16
1-4-4. BU (Optical Block) Repair Guide ............................. 1-16
1-4-5. BU Adjustment Flow [yy] ~ ...................................... 1-17
1-4-6. KEM-460AAA/C2RP Packing Spec. ....................... 1-171-4-7. KEM-460AAA/C2RP Packing .................................. 1-181-4-8. BU Data Decode Jig ................................................ 1-18
1-4-9. Loading For Service ......................................... 1-191-4-10. Laser Caution Label ................................................ 1-19
2. DISASSEMBLY
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram.................................................. 3-1
3-2. DSP Block Diagram ...................................................... 3-2
3-3. AV OUT Block Diagram ................................................ 3-3
4-3.................................. margaiDkcolBNALW/REHTE/BSU.4-3
5-3..........................................)2/1(margaiDkcolBrewoP.5-3
4. SCHEMATIC DIAGRAMS
4-1. This Note Is Common For Schematic Diagrams .......... 4-1
4-2. Frame Schematic Diagram........................................... 4-2
4-3. FR-310 Board (FRONT RIGHT) Schematic Diagram ... 4-34-4. FR-310 Board (USB FRONT CONNECTOR)
.....................................................
4-4
4-5.
HU-015 Board (USB HUB) Schematic Diagram...........
4-5
4-6. ANT-007 Board (ANTENNA) Schematic Diagram........ 4-6
4-16. MB-134 Board (AUDIO)
Schematic Diagram (9/15)............................................ 4-16
4-17. MB-134 Board (VIDEO)
Schematic Diagram (10/15).......................................... 4-17
4-18. MB-134 Board (GPIO/JTAG)
Schematic Diagram (11/15) .......................................... 4-18
4-19. MB-134 Board (ETHERNET)
Schematic Diagram (12/15).......................................... 4-19
4-20. MB-134 Board (FE_POWER/SF/SATA)
Schematic Diagram (13/15).......................................... 4-20
4-21. MB-134 Board (FE_OP/MOTOR DRIVE)
4-26. USB-024 Board (USB REAR CONNECTOR)
Schematic Diagram ...................................................... 4-24
4-27. Waveforms ................................................................... 4-25E
5. PRINTED WIRING BOARDS
5-1. This Note Is Common For Printed Wiring Boards ........ 5-1
5-2. SWB-001 Board (SWITCH) Printed Wiring Board........ 5-2
5-3. SWP-001 BoardPrinted Wiring Board ...................................................... 5-2
5-4. FR-310 Board (FRONT RIGHT)
Printed Wiring Board ................................................... 5-3
5-8. MB-134 Board (MAIN)
Printed Wiring Board (Side A) ...................................... 5-7
5-9. MB-134 Board (MAIN)
Printed Wiring Board (Side B) ...................................... 5-8
)RAER(draoB420-BSU.11-5
Printed Wiring Board .................................................... 5-10E
6. IC PIN FUNCTION DESCRIPTION ................... 6-17. SERVICE MODE ..................................................... 7-18. ERROR LOG LIST ................................................. 8-1
9. TROUBLESHOOTING ............................................. 9-1
10. REPAIR PARTS LIST
10-1. Exploded Views ............................................................ 10-1
10-1-1. Case Section ........................................................... 10-1
10-1-2. Front/Rear Chassis Section .................................... 10-2
10-1-3. Main Chassis Section .............................................. 10-3
10-1-4. BD Section .............................................................. 10-4
10-1-5. Accessories ............................................................. 10-510-2. Electrical Parts List ....................................................... 10-6
BDP-BX57/S570
4-22. MB-134 BOARD(IFD)
22-4............................................)51/51(margaiDcitamehcS
4-23. SWB-001 BOARD
4-24. SWP-001 BOARD
Schematic Diagram (14/15) ........................................ 4-21
Schematic Diagram ...................................................... 4-23
Schematic Diagram ...................................................... 4-23
4-13. MB-134 Board (USB) Schematic Diagram (6/15)......... 4-13
4-14. MB-134 Board (HDMI)
Schematic Diagram (7/15)............................................ 4-14
4-15. MB-134 Board (SATA)Schematic Diagram (8/15)............................................ 4-15
1-5. Harness Dressing ......................................................... 1-22
1-5-1. Harness (SIM-001).................................................. 1-22
1-5-2. USB (USB-007).......................................................
9-1.........................................................snoitcnufniaM.2-3-1
1-6. Power Cord Soldering Location ................................... 1-221-6-1. Soldering point for Switching Regulator (APS-257).... 1-22
1-6-2. Soldering point for Switching Regulator (SRV2206UC)1-22
)TSOH/HSALF(draoB431-BM.21-4Schematic Diagram (5/15)............................................ 4-12
4-7.
2-1. Disassembly Flow ........................................................ 2-1
2-2. Upper Case .................................................................. 2-1
2-3. Front Panel Block ......................................................... 2-2
2-4. BD Drive ....................................................................... 2-3
2-5. Wireless Lan Card Block,EM-002 Board and HU-015 Block................................
2-3
2-6. Rear Panel Block.......................................................... 2-42-7. MB-134 Board .............................................................. 2-4
2-8. Switching Regulator ..................................................... 2-5E
2-9. Circuit Boards Location ................................................ 2-5E
3-6. Power Block Diagram (2/2) .......................................... 3-6E
5-5. HU-015 Board (USB HUB) Printed Wiring Board 5-4
5-6. ANT-007 Board (ANTENNA) Printed Wiring Board ...... 5-5
5-7. ANT-008 Board (ANTENNA) Printed Wiring Board ...... 5-6
)rotcennoC(draoB200-ME.01-5
Printed Wiring Board .................................................... 5-9
ANT-008 Board (ANTENNA) Schematic Diagram........ 4-7
4-8. MB-134 Board (CXD9983GG/9984GG)
Schematic Diagram (1/15)............................................ 4-8
4-9. MB-134 Board (CXD9983GG/9984GG)
Schematic Diagram (2/15)............................................ 4-9
4-10. MB-134 Board (POWER1)
Schematic Diagram (3/15) ........................................... 4-104-11. MB-134 Board (CLK/POWER2)
Schematic Diagram (4/15) .......................................... 4-11
4-25. EM-002 BOARD.
Schematic Diagram ...................................................... 4-24
1-22
Schematic Diagram
Section Title Page Section Title Page
1-7. Avoid Switching Regulator Board
(APS-257) from Floating............................................... 1-23E
-
8/8/2019 Sony Bdp Bx57,s570
4/1321-1
BDP-BX57/S570SECTION 1
SERVICE NOTE
1-1. DISC REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION)
1. Remove the upper case. (Refer to page 2-1)
2. Insert a clip in the hole of a drive and open a tray.
Note:
1-2. Work when optical device are replaced
Note: Please do the following work when you replace the optical device.
1. Install it in PC after downloading two set of software from following URL.
(Refer to 1-4-9. BU Data Decode Jig on page 1-19)
STEP 1Microsoft .NET Framework Version 2.0 Redistributable Package (x86)
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5
STEP 2
Microsoft .NET Framework 2.0 Service Pack 1 (x86)
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5
2. Take a photograph of the bar code on the optical device. The valid bar code photo as shown in Fig.2
3. Drag-and-drop the bar code photograph to the icon of decode software (BDBUDec).
* The decode software is a complete set of BDBUDec, Tasman.Bars.dll, and SavePath.
* Because decode software cannot be attached, it separately distributes it.
4. Input the password when you start decode software.
* Inquire of each service headquarters because the password cannot be disclosed.
5. Write the decode data to the set.
(Refer to 1-4-4. BU (Optical Block) Repair Guide on page 1-16 and 1-4-5. BU Adjustment Flow [yy] on page 1-17)
tray
Fig.2
Fig.1
(Use clip diameter about 1.2 mm)
hole(12~
32)mm
clip
-
8/8/2019 Sony Bdp Bx57,s570
5/1321-2
BDP-BX57/S570
1-3. TEST DISC
Part No. Description Layer
J-6090-199-A BLX-104 Single Layer
J-6090-200-A BLX-204 Dual Layer
J-2501-307-A CD (HLX-A1)
J-2501-305-A HLX-513 Single Layer (NTSC)
J-2501-306-A HLX-514 Dual Layer (NTSC)
J-6090-077-A HLX-506 Single Layer (PAL)
J-6090-078-A HLX-507 Dual Layer (PAL)
1-3-1. Operation and Display
Check Items
1) BLX-104
1. Select 23.976Hz/1080p
2. Play 4.Motion pictures
3. Check whether player can play back or not
4. Check each outputsVideo:
Composite/component/HDMI
Audio:
Digital out (Coaxial/Optical)/Audio out/5.1Ch output
* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) can use instead of 1080/24p.
However this is temporary correspondence.
2) BLX-204
1. Select 1080i (59.94Hz or 50Hz)
2. Play 4.Motion pictures
3. Check whether player can play back or not
(Check the picture and sound output)
3) CD (HLX-A1)Check whether player can play back or not
(Check the sound output)
4) HLX-513/514 (NTSC), HLX-506/507 (PAL)
1. After displayed Main Menu, select 1.Video
2. Play 1.Color Bar 100%
(Check the picture and sound output)
3. Return to Menu
4. Play Demonstration 4:3 or 5.Demonstration 16:9
(Check the picture and sound output)
-
8/8/2019 Sony Bdp Bx57,s570
6/1321-3
BDP-BX57/S570
1-3-1-1.BLX-104 Menu Function (1)Main Menu
X
X
X
X
X
X
X
X
X
X X X
X X X
X
1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed.
1-3-1-2.BLX-104 Menu Function (2)Main Menu
Sub_menu1 is displayedTo Main Menu after playback from T2_C1 to T19_C1To Main Menu after playback of T20_C1To Main Menu after playback of T21_C1
Sub_menu3 is displayedTo Main Menu after playback from T54_C1 to T60_C1To Main Menu after playback of T61_C1
To Main Menu after playback of T62_C1
* When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively dis-
played.
* When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed.
* 5. AV Sync does not operate.Note:
Txx_ Cxx
Chapter No.
Title No.
-
8/8/2019 Sony Bdp Bx57,s570
7/1321-4
BDP-BX57/S570
1-3-1-3.BLX-104 Menu Function (3)Main Menu
To Main Menu after playback from T23_C1 to T40_C1
To Main Menu after playback of T41_C1
To Main Menu after playback of T42_C1
Sub_menu2 is displayed
To Main Menu after playback from T44_C1 to T50_To Main Menu after playback of T51_C1
To Main Menu after playback of T52_C1
Sub_menu4 is displayed
* When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively dis-
played.
* When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively
displayed.
* 5. AV Sync does not operate.
-
8/8/2019 Sony Bdp Bx57,s570
8/1321-5
BDP-BX57/S570
1-3-1-4.BLX-104 Menu Function (4)Sub menu1
X
X
X
X
X
X
1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selec-
tively displayed on Sub menu1 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively
displayed on Sub menu1 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/1080i
is selectively displayed.
6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.
7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return toSub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.
8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. ColorBar 100% is selectively displayed on Sub
menu1 screen.
9) At the selection of Main Menu, 1. VideoSignal of 1080/59.94i of Main Menu is selectively displayed.
10) AV Sync does not operate.
-
8/8/2019 Sony Bdp Bx57,s570
9/1321-6
BDP-BX57/S570
1-3-1-5.BLX-104 Menu Function (5)Sub menu2
X
X
X
X
X
X
1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is
selectively displayed on Sub menu2 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu2 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
23.976Hz/1080P is selectively displayed.
6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.
7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.
8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu2 screen.
9) At the selection of Main Menu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed.
10) AV Sync does not operate.
-
8/8/2019 Sony Bdp Bx57,s570
10/1321-7
BDP-BX57/S570
1-3-1-6.BLX-104 Menu Function (6)Sub menu3
X
X
X
X
X
X
1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is
selectively displayed on Sub menu3 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu3 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/1080i
is selectively displayed.
6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.
7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.
8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1. 1. Color Bar 100% is selectively displayed on Sub
menu3 screen.
9) At the selection of Main Menu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed.
10) AV Sync does not operate.
-
8/8/2019 Sony Bdp Bx57,s570
11/1321-8
BDP-BX57/S570
1-3-1-7.BLX-104 Menu Function (7)Sub menu4
X
X
X
X
X
X
1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is
selectively displayed on Sub menu4 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu4 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P
is selectively displayed.
6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.
7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return toSub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.
8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu4 screen.
9) At the selection of Main Menu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed.
10) AV Sync does not operate.
-
8/8/2019 Sony Bdp Bx57,s570
12/1321-9
BDP-BX57/S570
1-3-2-1.BLX-204 Menu Function (1)Main Menu
X
X
X
X
X
X
X
X
X
X X X X
X X
X
X
X
1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed.
1-3-2-2.BLX-204 Menu Function (2)Main Menu
Sub_menu1 is displayedTo Main Menu after playback from T2_C1 to T19_C1
To Main Menu after playback of T20_C1
To Main Menu after playback of T21t T63t T64t T65t T66
Sub_menu3 is displayedTo Main Menu after playback of T54_C1-T60_C1t T83_C1-T94_C1To Main Menu after playback of T61_C1
To Main Menu after playback of T62t T82
To Main Menu after playback of T67_C1
To Main Menu after playback of T83_C1
* When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively dis-
played.
* When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed.Note:
Txx_ CxxChapter No.
Title No.
1-3-2 Menu Function
-
8/8/2019 Sony Bdp Bx57,s570
13/1321-10
BDP-BX57/S570
1-3-2-3.BLX-204 Menu Function (3)Main Menu
Sub_menu4 is displayed
To Main Menu after playback from T23_C1 to T40_C1To Main Menu after playback of T41_C1
To Main Menu after playback of T42_C1
Sub_menu2 is displayed
To Main Menu after playback of T44_C1-T50_C1t T71_C1-T81_C1To Main Menu after playback of T51_C1
To Main Menu after playback of T52_C1t T69
To Main Menu after playback of T68_C1
To Main Menu after playback of T70_C1
* When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively dis-
played.
* When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively
displayed.
-
8/8/2019 Sony Bdp Bx57,s570
14/1321-11
BDP-BX57/S570
1-3-2-4.BLX-204 Menu Function (4)Sub menu 1
X
X
X
X
X
X
1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selec-
tively displayed on Sub menu1 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively
displayed on Sub menu1 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
59.94Hz/1080i is selectively displayed.
6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.
7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return toSub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.
8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. Color Bar 100% is selectively displayed on Sub
menu1 screen.
9) Selection of AV Sync t Return to Sub menu1 after playback of T67_C1. 1. Color Bar 100% is selectively displayed on Sub menu1
screen.
10) At the selection of Main Menu, 1. Video Signal of 1080/59.94i of Main Menu is selectively displayed.
-
8/8/2019 Sony Bdp Bx57,s570
15/1321-12
BDP-BX57/S570
1-3-2-5.BLX-204 Menu Function (5)Sub menu 2
X
X
X
X
X
X
1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is
selectively displayed on Sub menu2 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu2 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
23.976Hz/1080P is selectively displayed.
6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1 and from T71_C1 to T81_C1. SubPic that corresponds to Audio stream
1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.
7) Selection of Dolby AC-3 Audiot
Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.
8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1 and T69. 1. Color Bar 100% is selectively displayed on
Sub menu2 screen.
9) Selection of AV Sync t Return to Sub menu2 after playback of T70_C1. 1. Color Bar 100% is selectively displayed on Sub menu2
screen.
10) At the selection of Main Menu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed.
-
8/8/2019 Sony Bdp Bx57,s570
16/1321-13
BDP-BX57/S570
1-3-2-6.BLX-204 Menu Function (6)Sub menu 3
X
X
X
X
X
X
1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is
selectively displayed on Sub menu3 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu3 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/1080i
is selectively displayed.
6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1 and from T84_C1 to T94_C1. SubPic that corresponds to Audio stream
1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.
7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.
8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1 and T82. 1. Color Bar 100% is selectively displayed on
Sub menu3 screen.
9) Selection of AV Sync t Return to Sub menu3 after playback of T83_C1. 1. Color Bar 100% is selectively displayed on Sub menu3
screen.
10) At the selection of Main Menu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed.
-
8/8/2019 Sony Bdp Bx57,s570
17/1321-14
BDP-BX57/S570
1-3-2-7.BLX-204 Menu Function (7)Sub menu 4
X
X
X
X
X
X
1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed.
2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is
selectively displayed on Sub menu4 screen.
3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu4 screen.
4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.
5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P
is selectively displayed.
6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.
7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed.
During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return toSub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.
8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu4 screen.
9) Selection of AV Sync t Return to Sub menu4 after playback of T68_C1. 1. Color Bar 100% is selectively displayed on Sub menu4
screen.
10) At the selection of Main Menu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed.
-
8/8/2019 Sony Bdp Bx57,s570
18/1321-15
BDP-BX57/S570
1-4. DRIVE REPAIRING
1-4-1. Preparation
1-4-2. Checking Flow ~ Drive (BU) section ~
ESD Measures
It is necessary to check the working space ESD condition
before starting the Drive Part (BU) repairs
The ESD-resistance of BD Laser is weaker than DVD/CD Laser
To prevent ESD destruction, please make sure the working
space and human ESD.
BDP-S570 can play the BD-disc
BLX-104
BDP-S570 can play the DVD/CD-disc
Check Drive Power SupplyCN301 Pin 2: 12V / Pin 6: 5V
Check PS301, PS302, PS303Replace PS when open
Check / replace the FFC cable, then checkBDP-S570 operates normally
OP FFC cable (1-837-494-11)
Check the Optical Block Unit (BU) byservice mode. (Flowchart zz)
BU IOP is OK?Replace the Optical Block Unit (BU)
Optical Block Unit (BU) replace(Flowchart yy)
OK
DVD: HLX-513CD: HLX-A1
NO
YES
NO
YES
YES
NO NO
NO
SPDL FFC cable (1-837-495-11)
How to open FFC Holder. Refer below picture.
1
2
1
2
1
2
Drive flowchart
-
8/8/2019 Sony Bdp Bx57,s570
19/1321-16
BDP-BX57/S570
1-4-3. BU Check Flow [zz] ~
Before BU Replacement~
1-4-4. BU (Optical Block) Repair Guide
BDP 5G (BDP-S570) series component structure is as same as conventional DVD Players.
However BD player requires precise read out functions and also secure contents Protection
system.
Since above requirement, it is necessary to set/adjust BU data to EEPROM.
The following cases need Adjustments;
(1)Replace BU (MB is original)
(2)Replace MB (BU is original)
(3)Replace both BU and MB
JIG Requirement
Digital camera (recommend with macro mode)
Barcode decoder (5GBUJIG) installed in JIG PCs
USB memory
ESD work bench
Procedure (all cases) Refer the diagram
Remarks:
The servo adjustment procedure will be carried out during OP data Writing.
There is no manual adjustment procedure. LD ON TIME history doesnt carry over.
Do not touch any optical block parts, Turn Table and during replacing. BD Laser diode
is very sensitive!
Enter Service ModePress ., ,
and plug in AC Power
Inside *Service Mode MenuSelect [8] Drive
Inside *DriveSelect [8] OP Check Menu
Inside *OP Check MenuSelect [2] dIOP then press 'ENTER'
Specification dIOP
BD: 6mA
DVD, CD: 9mA
IOP out of specification need BUreplacement
Optical Block Unit (BU) replace(Flowchart yy)
AC Power OFF
NO
YES
Optical Block Unit (BU) IOP check flow(zz) ~ [Before BU Replacement]
+-
+-
-
8/8/2019 Sony Bdp Bx57,s570
20/1321-17
BDP-BX57/S570
1-4-5. BU Adjustment Flow [yy] ~
1-4-6. KEM-460AAA/C2RP Packing Spec.
Dont Reuse the bag!!
Open a box
Take a corrugated
cushion out
Dont touch the area!!
Open a bag
Open a cushion
Take BU out
Explanation:Mode: 1--> BDP-BX37/S270/S370/S373/S470
Mode: 2--> BDP-BX57/S570
Remove the defective BU from LoadingAssy and also remove BU insulator (4pcs)
Unpack new BU and take OP Data Barcode
photo by camera
Assemble BU with Insulators to LoadingAssy (tighten screw with 2kgf)
Decode the OP Data Barcode phot usingBDBUDEC.exe and save the test data to
USB memory(File Name: BuData.txt)
Enter Service Mode and insert USB memoryto USB connector
Select [8] Drive -->Select [1] Drive OP data Write -->
Select [2] Mode: 1 or 2Press ENTER
After Finishing ReWrite OP data--> Turn AC Power OFF
And confirm dIOP by select [8] OP CheckMenu to verify IOP in specification
IOP in specification --> Turn AC PowerOFF
Turn Power ON and check playback
performance using BD, DVD and CD
BLX-104
DVD: HLX-513CD: HLX-A1
The following cases need OP Data Write:(1) Replace BU (MB is original)(2) Replace MB (BU is original)(3) Replace both BU and MB
JIG requirementDigital camera (with macro mode)
Barcode decoder (BDBUDec.exe)installed in jigPC's (jig purpose)USB memoryESD free work bench
Optical Block Unit (BU) OP Data Write Flow (yy) ~ [After BU/MB Replacement]
-
8/8/2019 Sony Bdp Bx57,s570
21/1321-18
BDP-BX57/S570
1-4-7. KEM-460AAA/C2RP PACKING
1) Store it in Cushion Carton
2) Store it in Individual Carton
3) Store it in Master Carton
4) Master carton is sealed
with the PP tape.
Individual Carton (E430-BU-RP)
Individual Carton (E430-BU-RP)
Stick itto H.
PP Tape
Shipment Label
(CareMark 3)
AntistaticBag
Instruction
Manual
1 Process thebendof FFC.
(Doas well asthe statewhenmass
production is packed)
2 It isnecessary to fold theantistatic
bagin orderofA to B .
(Purpose: Toapply loosening to part C )
3 Setthe upper surface of theturntableto
the partof the 14 hole.
Store 10individual cartons1 step X 2 steps
= 20individualcartonsin themastercarton.
Master Carton (E430-BU-RP)
The side with theturnedflap is a
lid sideof the individual carton.
Cushion Carton (E430-BU-RP)
Thingthat is stopper ofOP.
1-4-8. BU Data Decode Jig
JIG Name: BDBUDec. exe J-6090-212-ARelease : 2009.02.19
Version : 1.0.0.0
Software Contents:
BDBUDec.exe ; Software
SavePath.ini ; decoded file destination setting file (initial destination is C:BuData.txt)
TasmanBars.dll ; decode dll
Uninst.exe ; unistall BDBUDec.exe from PC
Installations
1.Unzip files to any PC Folder
2.Check the attached Bar code photo click and drop onto BDBUDec.exe, the Password willbe required at first time only, no need P/W from second time.
3.If there is the error message (.NET frame work requirements) please apply
Microsoft .NET Framework 2.0 and 2.0 SP1 from Microsoft download site.
STEP 1
Microsoft .NET Framework Version 2.0 Redistributable Package (x86)
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5
STEP 2
Microsoft .NET Framework 2.0 Service Pack 1 (x86)
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5
Remarks:
Do not change the decoded file name BuData.txt.
-
8/8/2019 Sony Bdp Bx57,s570
22/1321-19
BDP-BX57/S570
1-4-9. Loading For Service
BDP 5G Loading Assy service parts consists from 3 parts.Holder, Clamper AssyLoading Assy
Holder FFCCurrently these parts are producing 2 vendors. But the THERE IS NO COMPATIBILITY
.So, please DO NOT MIX the and of Loading for service and original Loading.Loading for service A-1750-926-A
Loading AssyLaser Caution Label
Holder, Clamper Assy
Holder, FFC4-167-321-01
(FFC Holder can be used
both service parts and original
parts)
3-087-220-21
Tape, Non Halogen
1-837-494-11
FFC
1-837-496-11
FFC
1-837-495-11
FFC
1-4-10. Laser Caution Label
The Loading Assy service parts does not have Laser Caution Label.
So that please reuse the original Laser Caution label and paste it on top of
new Loading Assy.
Limit SampleFollowing peel off condition are acceptable
-
8/8/2019 Sony Bdp Bx57,s570
23/1321-20
BDP-BX57/S570
In case of BU assy replacement:
1. OP related data for new assy is controlled by BU factory2. All of data is recorded into a barcode label
3. The label is put on the assy4. Service parts will be followed5. In service, the data should be read out from problem assy6. The read data should be saved to new assy
Fact finding:
1. The label is DATA MATRIX format2. The number of data is 91 words3. The method of reading and saving is required when BU and
main board are replaced.
New service method
1. All of BU data on the barcode label is shot by digital camera inorder to make a JPEG file of BU data.
2. Application software in the PC makes digital data from JPEG file.
3. The converted data is stored to USB memory.
4. The USB memory is connected to BDP 5G unit.
5. In service mode, there is a command to save the data from USBmemory to board memory.
-
8/8/2019 Sony Bdp Bx57,s570
24/1321-21
BDP-BX57/S570
Shoot the barcode
Format is JPEG
Application Software
Data convert fromJPEG TEXT
Save the TEXT data
The application software will be a service jig with J parts number asservice jig, and the recording media will be CD-R.
PN: J6090212ADescription: BDBUDEC
When instruction to PC, password is required.
The password will be supplied to only service HQ, and service center
name, quantity and all of software registered information should bemaintained by service HQ, and Video will ask to report the registrationinformation.
JIG Name: BDBUDEC J-6090-212-A
Release : 2009.02.19
Version : 1.0.0.0
Software Contents:
BDBUDec.exe ; Software
SavePath.ini ; decoded file destination setting file
(initial destination is C:BuData.txt)
TasmanBars.dll ; decode dll
Uninst.exe ; unistall BDBUDec.exe from PC
Installations
1.Files to any PC Folder
2.Check the attached Bar code photo click and drop onto BDBUDec.exe, the password will
be required at first time only, no need P/W from second time.
3.If there is the error message (.NET frame work requirements) please apply
Microsoft .NET Framework 2.0 and 2.0 SP1 from Microsoft download site.
STEP 1
Microsoft .NET Framework Version 2.0 Redistributable Package (x86)
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-
8edd-aab15c5e04f5
STEP 2
Microsoft .NET Framework 2.0 Service Pack 1 (x86)http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-
aacf-a7633f706ba5
Remarks:
Do not change the decoded file name BuData.txt.
USB device is connected
to symbol on therear unit, and the TEXT
data as new data is
loaded to unit by Service
Mode.
-
8/8/2019 Sony Bdp Bx57,s570
25/1321-22
BDP-BX57/S570
1-5. HARNESS AND USB DRESSING1-5-1. Harness (SIM-001)
- Harness (SIM-001) MUST ALWAYS under the board to board connector
1-5-2. USB (USB-007)
- USB Harness ALWAYS place on the chasis by using Non-Halogen tape
Follow the designated destination according to the mark indicated on the board
1-6. Power Cord Soldering location
1-6-1. Soldering point for Switching Regulator (APS-257)
1-6-2. Soldering point for Switching Regulator (SRV2206UC)
- (BDP-BX57/S570: EXCEPT US, CND)
Mount the Power Supply Cord as indicated
- (BDP-BX57/S570: US, CND Only)
Mount the Power Supply Cord as indicated
-
8/8/2019 Sony Bdp Bx57,s570
26/1321-23E
BDP-BX57/S570
1-7. Avoid Switching Regulator Board (APS-257) from Floating
Stick the Non-Halogene tape
as shown. Make sure the tape
is strongly stick to both of
MB-134 board and Switching
Regulation board.
(BDP-S570 : AEP, UK, AUS)
-
8/8/2019 Sony Bdp Bx57,s570
27/132
2-1
BDP-BX57/S570SECTION 2DISASSEMBLY
This set can be disassembled in the order shown below.
Note: Follow the disassembly procedure in the numerical order given.
2-2. UPPER CASE
tapping screw(tightening torque = 5 to6 kgfcm)
1 tapping screw(tightening torque =5 to 6 kgfcm)
2
three screws(tightening torque = 5.0 to 6.0kgfcm)
3
2-1. DISASSEMBLY FLOW
Upper case
2-2. UPPER CASE
(Page 2-1)
2-3. FRONT PANEL BLOCK
(Page 2-2)
2-4. BD DRIVE(Page 2-3)
2-6. REAR PANEL BLOCK
(Page 2-4)
2-5. WIRELESS LAN CARD BLOCK
(Page 2-3)
2-8. SWITCHING REGULATOR(Page 2-5)2-7. MB-134 BOARD,HU-015 BORD
(Page 2-4)
SET
-
8/8/2019 Sony Bdp Bx57,s570
28/1322-2
2-3. FRONT PANEL BLOCK
4 Two Coaxial Cables
blackgray
6 Front Panel Block
3 Seven Claws
Tray cover assy2
1 Eject
5 Harness (CN1509)
BDP-BX57/S570
hookrib
Coaxial-B ANT-00
8
slit
hookrib
Coaxial-B ANT-00
8
slit
ANT-007
SWP-00
2
hook
slit
Coaxial
-W
ANT-007
SWP-00
2
hook
slit
Coaxial
-W
SWB-00
1
slit
SWB-00
1
slit
Arrangement ofcoaxial cable and harness dressing
-
8/8/2019 Sony Bdp Bx57,s570
29/1322-3
BDP-BX57/S570
2-5. WIRELESS LAN CARD BLOCK , EM-002 BOARD AND HU BOARD
2-4. BD DRIVE
Arrangement of harness
and Hamelone Tape
When USB harness removed,
Please ensure the USB harness
is properly redressed and sticked
new tape at the same location as shown
in the picture.
2 Flexible Flat Cable(Optical)(CN1401)
3
(CN2460)
4
(CN2470)
5 BD drive
1 four screws (BV3)(tightening torque = 6.0 to 7.0 kgfcm)
Flexible Flat Cable(Spindle)
Flexible Flat Cable(loading)
2 two tapping screw(tightening torque = 6.0 to 7.0 kgfcm)
4
wireless LAN card block
3 harness (USB-015)(CNxxx)
1 two coaxial cables
black
gray
EM-002 Board7
5 Harness (USB-014)(CN402)
6 two tapping screw(tightening torque = 6.0 to 7.0 kgfcm)
-
8/8/2019 Sony Bdp Bx57,s570
30/1322-4
BDP-BX57/S570
2-7. MB-134 BOARD
11 five screws (BV3)(tightening torque = 6.0 to 7.0 kgfcm)
13 MB-134 board
2
flexible flat cable10
harness
(CN1503)
12 harness (SIM-005)
7
flexible flat cable(CN2460)
8(CN2470)
9
flexible flat cable
(CN1401)
2-6. REAR PANEL BLOCK
Note: Do not injure by the sharp
edge of the heat sink.
3harness (MH-121)
(CN102)
4harness (USB-009)
(CN104)
HU-015 board
HU socket6
1harness (USB-014)
(CN101) 2 harness (USB-010)
(CN103)
four screws (BV3)5
14
seven screws (BV3)
(tightening torque = 6.0 to 7.0 kgfcm)
screw (P3)(tightening torque = 3.0 to 4.0 kgfcm)
5
rear panel block
2
fan harness(CN1503)
3
4
1
Lift-up power cord from chasis
(CN1509)
-
8/8/2019 Sony Bdp Bx57,s570
31/1322-5E
BDP-BX57/S570
2-9. CIRCUIT BOARDS LOCATION
FR-310 board
switching regulator
SWP board
MB-134board
USB-024boardwireless LAN card
HU-015 board
ANT-008 board
EM-002 board
2-8. SWITCHING REGULATOR
ANT-007 board
SWB board
two screws (BV3)(tightening torque = 6.0 to 7.0 kgfcm)
3Switching regulator
Lift up Power Cord from chasis51
2
3Boad to board connector
(CN301)
-
8/8/2019 Sony Bdp Bx57,s570
32/132
T701 FR_6V
SWP-001 BOARD
Y
PB
PR
L
R
CN1201LAN(100)
IC1201ETHERNET
PHY
X120125MHZ
(AC IN)
A
3-1
BDP-BX57/S570
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
PS301PS302PS303PS304
The components identified by
mark or dotted line with markare critical for safety.
Replace only with part number
specified.
IC1003VIDEO AMP
IC901D/A CONVERTER
HUB
REAR
HDMI
USB
USB
ETHERNET
VIDEO
AUDIO(ANALOG OUTPUT)
(DIGITAL OUTPUT)AUDIO
MB-134 BOARD
A-BUS
IC204IC205
IC104
IC105
IC501
IC502
2G/16GNANDFLASH
S-FLASH16M
X40127MHZ
X80225MHZ
IC1504
P FAIL
IC1503SUB SYSTEM
CONTROL
CN371
IC701REMOTECONTROLRECEIVER
IC702
FL DRIVER
Blu-rayDVD
DRIVE
BD DRIVE
S401STOP
S402OPEN/CLOSE
S403PLAY
SWB-001 BOARD
FR-310 BOARD
ND701FLUORESCENT
INDICATORTUBE
Q706,Q707
CONVERTERDC/DC
D702(WHITE)
S331POWER
POWER-1UNSW6V
USB-024BOARD
SWITCHINGREGULATOR
CN1503
M1501FAN
3
2
1
PS701FR_6V
IC2301
IC2401
SADRIVE
MOTORDRIVE
HU-015BOARD
REGULATOR
IC102IC103IC105
IC104
USB HUBCONTROLLER
ANT-008BOARD
WIRELESS LAN CARD
(WLAN MODULE)+5V
+3.3V+5V
+3.3V
UNSW6V
USB - FRONT
USB - WLAN
ANT-007BOARD
DDR2_1.8VVREF_0.9VDDR2_VTT0.9VCPU1.2VAVDD12_HDMICPU3.3VCORE_STB3.3VAVDD33_HDMIDAC3.3VA
FE_SW5VFE_SW12VUNSW3.3VUSB5VHDMI5V
IC301
IC3 02
IC303
IC304
IC305
IC307
IC308
IC309
IC310
IC601
IC704
IC703
IC803
IC804
USB
OPTICAL
CN701
HDMIOUT
COAXIAL
J902
AUDIO
LINE OUT
DIGITALOUTPCM/DTS/DOLBY
DIGITALIC904
OPTICALTRANSMITTER
VIDEO
COMPONENTVIDEOOUT
J904
B-BUS
SATA I/F, MEMORY CONTROL,A/V OUT, HDMI, ETHERNET I/F,
USB I/F
MAIN SYSTEM CONTROL, DSP
CXD9983GG/CXD9984GG
IC101
IC1501
CONTROLFAN
USB
REGULATOR
CN361
D709(GREEN)
EXT
EXT
-
8/8/2019 Sony Bdp Bx57,s570
33/132
-
8/8/2019 Sony Bdp Bx57,s570
34/132
CEC PULL-UP
ISOLATINGSWITCH
VIDEOAMP
IC101
IC1003
IC901
C33
B32A33
75
3
1
8
14
D30
H14
G15
Y
PB
PR
78
9
10
C23E23B22D22
H20
A19
D26
B26
C27
A27
D28
C29
A29
G39
B28
10
11
13
15
11
16
1
YINPBINPRIN
VIN
MUTE
SD/HD
PYOUT
PBOUT
PROUT
VOUT
J904
L
R
IC904OPTICALTRANSMITTER
TX2P1
34
6
7
9
10
12
19
13CEC
IT-CON
Q702PG3-4
3-3. AV OUT BLOCK DIAGRAM
3-3
BDP-BX57/S570
VIDEO
AUDIO
LINE OUT
COMPONENTVIDEO OUT
COAXIAL
OPTICAL
DIGITALOUTPCM/DTS/DOLBY
DIGITAL
CN701
J902
D/A CONVERTER
AOUTL
AOUTR
XMUTE
DACDATLRCK
BCLK
MCLK
D901IFCON_XMUTE
DAC3.3VA
Q909BUFFER
TX2N
TX1P
TX1N
TX0P
TX0N
TXKP
TXKN
TMDS DATA2+
TMDS DATA2-
TMDS DATA1+
TMDS DATA1-
TMDS DATA0+
TMDS DATA0-
TMDS CLOCK+
TMDS CLOCK-
HPD
CEC
HDMIOUT
TX2P
TX2NTX1P
TX1N
TX0P
TX0N
TXKP
TXKN
CH2_P
CH2_M
CH1_P
CH1_M
CH0_P
CH2_M
CLK_P
CLK_M
HTPLG
SPDIF
AMUTE
AOMCKAOBCKAOLRCKAOSDATA0
VIND8
VIND6
DACOUT6
FORMAT1
XVMUTE
CVBS
YPBPRDACOUT1
DACOUT3DACOUT2
LORTN
OCYROMEMF/IATAS
F/ITENREHTEIMDH,T
UOV/A
F/IBSU
GG4899DXC/GG389
9DXC
PSD
,LORTNOC
METSYSNI
AM
XAMUTE
MB-134 BOARD
-
8/8/2019 Sony Bdp Bx57,s570
35/132
MB-134 BOARD
USB-024
BOARD
CN1102
CN1502
X1201
25MHz
IC1201
10
R
LED_DT
LED_CK
FLD_STB
SIRCS_IN
LAN (100)
USB
C43
D40
D42
E39
D38
F36
B38
C41
A43
H34
A41
B40
C39
A39
C37
F38
E37
B42
32
B34
G33
A35
C19
D34
A17
E35
AV12
A1431
C35 FrontendcircuitMRESET
C35 CPU_PRERSTCPU_PRERST21
GPIO2
GPIO1
CORE_RESETB
GPIO6
VSTB
GPIO4
GPIO5
A37
D36
AW11
AY10
3148KEY1
FR-310 BOARD
10
8
11
13
6
10
8
11
13
6
7
9
8
IC702
FL DRIVERIC701
REMOTE
CONTROL
RECEIVER
DIN
CLK
STB
TUBE
FLOURESCENTINDICATOR
Q709
LED DRIVER D702(WHITE)
ND701CN702
GRD1 - GRD8
SEG1 -SEG17
CN1504
CN402
S401
S402
S403
S331
SWB-001 BOARDCN509
CN401CN331
SWP-001 BOARD
2
3
4
5 2 2
47KEY2
46KEY3
49KEY0
2
3
4
5
KEY1
KEY2
KEY3
KEY0
CN1201
3 2CN371
3-4. USB/ ETHER/ WLAN BLOCK DIAGRAM
3-4
BDP-BX57/S570
GG4899DXC/GG3899DXC
2
3
2
3
CN602DP
DM
HU-015 BOARD
ANT-008BOARD
WIRELESSLAN CARD
(WLAN
MODULE)
ANT-007BOARD
CN103
31
30
32 33
4
3
2
1
USBUP_DM
USBUP_DP
USBDN2_DM
USBDN2_DP
USBDN1_DM
USBDN1_DP
X10124MHz
3 2
DPDM
CN104
6
7 7
6 6
7 7
6
EM-002BOARD
DP
DM
CN101
L401
USB
3 2
D-
D+
Q710
LED DRIVER D709(GREEN)
15 15
CN372
IC104
IC1503
11
34
LED-GREEN
LED-WHITE
-
8/8/2019 Sony Bdp Bx57,s570
36/132
The components identified bymark or dotted line with mark
are critical for safety.Replace only with part number
specified.
1
10
6
2
6
2
10
IC1001
IC1002
IC305
4 4
6
18
1
CN301
VCC1
2
1
9
7
8
9
7
8
SWITCHINGREGULATOR:
IC 308
DCDC 4V
+3.3V
IC309
IC704
+3.3V1
1
IC105
IC205
1
1
IC104
IC204
IC101
AVDD33_HDMI
CORE_STB1.1V
IC901
IC1003
VIDEOBUFFER
AUDIODACPCONT3
PCONT3
+3.3V
-5V
PCONT2
DAC 3.3VA
VIDEOBUFFER 3.3V
IC310
IC311
IC303
IC307
IC 501
NANDFLASH
1
1
1
1
DDR2_1.8V
VREF_0.9VDDR2_VTT0.9V
1.2V CPU1.2V
AVDD12_HDMI
3.3V CPU3.3V
CORE_STB3.3V
IC 312
+5V
ATA_PCONT
IC 1451
IC 2401
USB_VBUS_PCONT2
USB_VBUS_PCONT1
IC 304
+5V
IC 601
IC 602
+5V
IC 705
+5V
FE_SW5V
FE_SW12V
IC 2301MOTORDRIVER
3 .3V 1 .2V
FE_SW5V
FE_SW3.3V
IC 301
+3.3V
IC 904
COAXIAL
OPT
SW5VA
18
18
NISECON
ICE
3.3V
SW3.3V
3.3V
3.3V
5V8V
IC 1503
IF CON
IC 1501
FAN
CN1503
M1501
FAN
Q501
Q502
MB-134 BOARD
PCONT2
PCONT3
PCONT4
PCONT_CORE
ATA_PCONT
FAN CONTROL0
FAN CONTROL1FAN CONTROL2
FAN CONTROL3
BDP-BX57/S570
3-5
3-5. POWER BLOCK DIAGRAM (1/2)
J902
3-4
7
6
1
UNSW3.3V
(AC IN)
UNSW12V
PCONT 2
PCONT 1
UNSW6V UNSW6VPS302
CN301
PS303UNSW-6V
F E- UN SW -6 V F E- UN SW 6V
FE-UNSW12V PS301 FE-UNSW12V
REGULATOR
REGULATOR
REGULATOR
PCONT3REGULATOR
PCONT_CORE
DC DC CON1.1V
REGULATORPCONT3
SERIALFLASH
IC 502
ETHERPHY
IC 201
+3.3V
PCONT3
REGULATOR+1.2V
REGULATOR0.9V
PCONT4
DC DC +1.8V
REGULATORQ303
Q302REGULATOR
PCONT3
FR_6V
MOTORDRIVER
+8V
CN1102
CN1101
REGULATOR
REGULATOR
REGULATOR
HDMI5V
USB 5V
USB 5V+5V
REGULATOR
REGULATORUNSW3.3V
REGULATOR
CN 1502
(IFCON FLASH WRITER)
USB-024
CN362 CN361CN601
HDMIOUT
CN701
CN1504
CN1401
SDRAMDDR2
SDRAMDDR2
SDRAMDDR2
SDRAMDDR2
4 4
3-4
7
6
1
PS701Q703,Q704B+SWITCH
D702LED WHITE
Q706,Q707DCDC
CONVERTER
Q709LED DRIVE D705,D706
RECT
IC701REMOTE CONTROL
R708
RECEIVERIC702
FLDRIVE
ND701FLUORESENT
INICATORTUBE
FLD_PCONT
LED_W
1 EXTCN371
IT_3.3V
CXD9983GG/CXD9984GG
APS-257(BDP-S570:EXCEPTUS,C
ND)
SRV2206UC(BDP-BX57/S570:US,C
ND)
FR-310 BOARD
PCONT3
UNSW6VPS304
CN372
CN702
CN602
3 4
CN302
4
CN602
UNSW6V USB_VBUS_PCONT1
POWER-2A
USB
USB
1 5 1 5
D709LED GREEN
Q709LED DRIVE
LED_G
EXT
-
8/8/2019 Sony Bdp Bx57,s570
37/132
The components identified bymark or dotted line with mark
are critical for safety.Replace only with part number
specified.
BDP-BX57/S570
3-6E
3-6. POWER BLOCK DIAGRAM (2/2)
3,4
CN102
CN101
UNSW6V 5.8V
USB_VBUS_PCONT1
+5V
CN104 CN371CN372
4 4 1VBUS
3,
4 VBUS
+5VREGULATOR
IC105
FB101
USB Front BOARD
WIRELESSLAN CARD
(WLAN MODULE)
POWER-1(SEE PAGE 3-5)
A
HU-015 BOARD
CN103
4
D109
+3.3VREGULATOR
IC102
D110
+5VREGULATOR
IC103
D111
USB HUBCONTROLLER
IC104
PRTPWR1P_CON_P1
12VBUS_DET
(USB)
4,
6
16 PRTPWR2
CN401CN402
EM-002 BOARD
3
4
3
4
-
8/8/2019 Sony Bdp Bx57,s570
38/1324-1
BDP-BX57/S570
SECTION 4
SCHEMATIC DIAGRAMS
All capacitors are in F unless otherwise noted. pF : F.
50V or less are not indicated except for electrolytics and tantalums.
All resistors are in ohms, 1/4 W (Chip resistors : 1 /10 W) un-less
otherwise specified.
k=1000, M=1000k.
% : indicates tolerance.
Caution when replacing chip parts.New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, because
it is damaged by the heat.
Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
: nonflammable resistor
: fusible resistor
: panel designation
f : internal component.
: adjustment for repair.
: B+ Line
: B Line
Circled numbers refer to waveforms.
Voltages are dc between measurement point.
Readings are taken with a color-bar signals on Blu-ray disc.
Readings are taken with a digital multimeter (DC 10M).
Voltage variations may be noted due to normal production toler-
ances.
Note:
The components identified
by mark or dotted line with
mark are critical for safety.
Replace only with part num-
ber specified.
Note:
Les composants identifis par
une marque sont critiques
pour la scurit.
Ne les remplacer que par une
pice portant le numro spcifi.
When indicating parts by reference number, please include the
board name.
4-1. THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
-
8/8/2019 Sony Bdp Bx57,s570
39/132
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
BDP-BX57/S570
4-2
4-2. FRAME SCHEMATIC DIAGRAM
APS-257(BDP-S570: EXCEPT US, CND)
SRV2206UC
(BDP-BX57/S570: US, CND ONLY)
15 16
K
L
KEM-460AAA/C2RP
-
8/8/2019 Sony Bdp Bx57,s570
40/132
4-3
BDP-BX57/S570
4-3. FR-310 BOARD (FRONT RIGHT) SCHEMATIC DIAGRAM- Ref. No.: FR-310 board; 20,000 series -
NO MARK:PB MODE
9
D
E
111052
FR-310 BOARD
3
I
F
12
C
1 86
XX MARK:NO MOUNT
G
A
13
H
74
B ND701
PT6315
IC702
0
0
5.6
5.6
3.3
0.1
5.75.6
4.9
3.3 3.3
3.3
-18.5
-21
-11.
1
-21
-20.9
-11.2
-11.5
-13.8
-13.
6
18.5
-9
13.7
-21
-21
-21
13.7
-21.4
-16.2
-18.7
3.3
-18.7
-18.8
-18.7
-18.7
-18.7
-18.7
-18.8
1.9
0.1
3
2.6
IC701 REMOTE CONTROL RECEIVER
FLUORESCENT INDICATOR TUBE
3.3
0.1
3.3
0.1
Note:The components identifiedby mark or dotted line with
mark are critical for safety.Replace only with part num-
ber specified.
Note:Les composants identifis parune marque sont critiques
pour la scurit.Ne les remplacer que par une
pice portant le numro spcifi.
See page 5-3 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
41/1324-4
BDP-BX57/S570
4-4. FR-310 BOARD (USB FRONT CONNECTOR) SCHEMATIC DIAGRAM- Ref. No.: FR-310 board; 20,000 series -
See page 5-3 for printed wiring board.
4PCN371
A USB FRONT CONNECTOR
(SEE PAGE 4-7)
XX MARK:NO MOUNT
BOARDHU-015
1
B
FR-310 BOARD
CNXXX
432
1
2
3
4
5
GND
5P
CN372
-
8/8/2019 Sony Bdp Bx57,s570
42/132
4-5
BDP-BX57/S570
4-5. HU-015 BOARD (USB HUB) SCHEMATIC DIAGRAM- Ref. No.: HU-015 board; 20,000 series -
NO MARK:PB MODE
USB HUB
9
D
E
1110 1552
HU-015 BOARD
3
I
F
12
C
1 86
XX MARK:NO MOUNT
G
14
A
13
H
74
J
B
5 5
3.3
5.8
3.3 8 .
53.3
3.3
IC105
+5V REGULATOR
IC102
+3.3V REGULATOR
IC103
+5V REGULATOR
3.3
5.8
5 5
See page 5-4 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
43/1324-6
BDP-BX57/S570
3P
CN201
PAT201
ANTENNA
2
ANT-007 BOARD
3
05
1
A
B
GRY WIRELESS
LAN CARD
4-6. ANT-007 BOARD (ANTENNA) SCHEMATIC DIAGRAM
- Ref. No.: ANT-007 board; 20,000 series -
See page 5-5 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
44/1324-7
BDP-BX57/S570
3P
CN301
PAT301WIRELESS
A
ANT-008 BOARD
BLK
1 2
05
ANTENNA
LAN CARD
3
B
4-7. ANT-008 BOARD (ANTENNA) SCHEMATIC DIAGRAM
- Ref. No.: ANT-008 board; 20,000 series -
See page 5-6 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
45/132
4-8
BDP-BX57/S570
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-8. MB-134 BOARD (CXD9983GG/9984GG) SCHEMATIC DIAGRAM (1/15) See page 5-7 for printed wiring board.- Ref. No.: MB-134 board; 10,000 series
-
8/8/2019 Sony Bdp Bx57,s570
46/132
4-9
BDP-BX57/S570
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-9. MB-134 BOARD (CXD9983GG/9984GG) SCHEMATIC DIAGRAM (2/15) See page 5-7 for printed wiring board.- Ref. No.: MB-134 board; 10,000 series
-
8/8/2019 Sony Bdp Bx57,s570
47/132
4-10
BDP-BX57/S570
5.8 5.0
3.3 0
3.3
3.7 1.2
0
3.7 3.3
03.3
3.7
3.3
3.3
0
0
3.35.8
3.8
11.8
5.7
5.7
1.1
1.1
3.3
11.8
8.11
1.8
1.8
1.8
3.3
1.8
3.7
0.9
0.9
11.911.9
5.0
8.0
0
5.85.0
3.3 0
1.8
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-10. MB-134 BOARD (POWER1) SCHEMATIC DIAGRAM (3/15) See page 5-7 for printed wiring board.- Ref. No.: MB-134 board; 10,000 series -
The components identifi edby mark or dotted line with
mark are critical for safety.Replace only with part number
specified.
-
8/8/2019 Sony Bdp Bx57,s570
48/132
BDP-BX57/S570
4-11
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-11. MB-134 BOARD (CLK/POWER2) SCHEMATIC DIAGRAM (4/15) See page 5-7 for printed wiring board.
- R ef . N o. : M B- 13 4 b oa rd ; 1 0, 00 0 s er ie s -
-
8/8/2019 Sony Bdp Bx57,s570
49/132
4-12
BDP-BX57/S570
3.3
0
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
3.3
0
3.3
3.3
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-12 . MB-134 BOARD (FLASH/HOST) SCHEMATIC DIAGRAM (5/15)- Ref. No.: MB-134 board; 10,000 series -
See page 5-7 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
50/132
BDP-BX57/S570
4-13
5.8
5
5.8 5
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-13. MB-134 BOARD (USB) SCHEMATIC DIAGRAM (6/15)- Ref. No.: MB-134 board; 10,000 series -
See page 5-7fo r printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
51/132
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-14
4-14. MB-134 BOARD (HDMI) SCHEMATIC DIAGRAM (7/15)- Ref. No.: MB-134 board; 10,000 series -
BDP-BX57/S570
See page 5-7 for printed wiring board.
3.3 3.3
5.8
-
8/8/2019 Sony Bdp Bx57,s570
52/132
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-15
BDP-BX57/S570
4-15. MB-134 BOARD (SATA) SCHEMATIC DIAGRAM (8/15)- Ref. No.: MB-134 board; 10,000 series -
See page 5-7 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
53/132
4-16
BDP-BX57/S570
5
1.8
2.5
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
1.65
5
1.6
1.8 1.6 3.3
0
)kcab
yalp
gni
rudyln
o(
56.1
3.31
.65
7.1
6.1
-
3.3 0
(only during playback)3.3
3.3
(only duringplayback)3.3
4-16. MB-134 BOARD (AUDIO) SCHEMATIC DIAGRAM (9/15)- Ref. No.: MB-134 board; 10,000 series -
See page 5-7 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
54/132
BDP-BX57/S570
4-17
0.3
3.3
0.7
0
-5
0.7
0.3
3.3 -5
0
0
0
0
0
3.3
1
4
3
2
8
5
6
7
0
3.3
-50.
6-
3.3
3.3
0.6
0
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-17. MB-134 BOARD (VIDEO) SCHEMATIC DIAGRAM (10/15)- Ref. No.: MB-134 board; 10,000 series -
See page 5-7 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
55/132
BDP-BX57/S570
4-18
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-18. MB-134 BOARD (GPIO/JTAG) SCHEMATIC DIAGRAM (11/15)- Ref. No.: MB-134 board; 10,000 series -
See page 5-7 for printed wiring board.
-
8/8/2019 Sony Bdp Bx57,s570
56/132
BDP-BX57/S570
4-19
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
See page 5-7 for printed wiring board.
- Ref. No.: MB-134 board; 10,000 series -
4-19. MB-134 BOARD (ETHERNET) SCHEMATIC DIAGRAM (12/15)
0
003 0 0
0
0
0
0
0
0
3.3
3.3
3.3
3.3
3.3* * * *
*
*
*
*
*
3.3
0
2.0
2.1
-
8/8/2019 Sony Bdp Bx57,s570
57/132
BDP-BX57/S570
4-20
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
3.3
3.3
1.2
1.2
1.2
12
12
5
5
5
5
5
5
5
5 5
5
12
12
12
1.4
1.4
1.4
1.4
1.4
1.4
1.4
4-20. MB-134 BOARD (FE_POWER/SF/SATA) SCHEMATIC DIAGRAM (13/15)
- Ref. No.: MB-134 board; 10,000 series -
See page 5-7 for printed wiring board.
POWER (12V;5V)
POWER (3.3V;1.2V);
MOTOR DRIVER (SA)
TO B/E
-
8/8/2019 Sony Bdp Bx57,s570
58/132
BDP-BX57/S570
4-21
3.3
12 8
8
3.3
5
5
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
- Ref. No.: MB-134 board; 10,000 series -
4-21. MB-134 BOARD (FE_OP/MOTOR DRIVE) SCHEMATIC DIAGRAM (14/15) See page 5-7 for printed wiring board
-
8/8/2019 Sony Bdp Bx57,s570
59/132
4-22
BDP-BX57/S570
3.3
5.7
3.3
3.3
3 0 00 3.3
3.3
3.3
0 0 3.3.4
2
3.3
3.3
3.3
3.3
3.2
3.1
3.3
0
0
0.2
3.3
3.3
3.3
3.3
3.3.2
3 3.2
3.3
003.2.
3
3
3.3
3.2
0
3.3
0
12 0 0 0
00
1
A
B
C
D
E
F
G
H
I
J
2 12 1311109876543 14
4-22. MB-134 BOARD (IFD) SCHEMATIC DIAGRAM (15/15) See page 5-7 for printed wiring board.- Ref. No.: MB-134 board; 10,000 series -
ForBDP-BX57/S570
-
8/8/2019 Sony Bdp Bx57,s570
60/132
BDP-BX57/S570
4-23
4-23. SWB-001 BOARD SCHEMATIC DIAGRAM- Ref. No.: SWB-001 board; 20,000 series -
See page 5-2 for printed wiring board.
4-24. SWP-001 SCHEMATIC DIAGRAM
- Ref. No.: SWP-001 board; 20,000 series - See page 5-2 for printed wiring board.
2
SWP-001 BOARD
31
A
B
2
SWB-001 BOARD
31
A
B
-
8/8/2019 Sony Bdp Bx57,s570
61/1324-24
BDP-BX57/S570
4-25. EM-002 BOARD SCHEMATIC DIAGRAM- Ref. No.: EM-002 board; 20,000 series -
A
EM-002 BOARD
1 2 3
B
See page 5-9 for printed wiring board.
4-26. USB-024 BOARD (USB REAR CONNECTOR) SCHEMATIC DIAGRAM- Ref. No.: USB-024 board; 20,000 series -
See page 5-10 for printed wiring board.
BOARD
(SEE PAGE 4-13)
MB-134
CN602(6/14)
USB REAR CONNECTOR
2
USB-024 BOARD
3
05
1
XX MARK:NO MOUNT
A
4
B
EXT
5V
-
8/8/2019 Sony Bdp Bx57,s570
62/132
H
1.0Vp-p
H
1.4Vp-p
MB-134 BOARD
25 MHz
2.1 Vp-p
25 MHz
2.0 Vp-p
Vpp
Vpp
H
1.2Vp-p
1 (VIN)IC1003
IC1003
IC1003
IC1003
IC1003
IC1003
IC1003
(PYIN)7
(PBIN)5
(PRIN)3
(PROUT)13
11
(YOUT)10IC1003
IC1003 (VOUT)15
(PBOUT)
IC101 (NS_XTAL_I)
27 MHz
3.3 Vp-p
Vpp
IC101 (XTAL25MI)
IC1201 (CLKIN)14
BDP-BX57/S570
4-25E
4-27. WAVEFORMS
H
0.7Vp-p
H
1.4Vp-p
H
2.0Vp-p
H
2.4Vp-p
H
0.7Vp-p
A25
BB8
-
8/8/2019 Sony Bdp Bx57,s570
63/1325-1
BDP-BX57/S570
SECTION 5
PRINTED WIRING BOARDS
5-1. THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
2 1
3
2 1
3
2 1
3
3 4 5
2 1
1 2 3
6 5 4
E B
C
3 1
55
2
4 6
1 2 3
5 4
Transistor Diode
: Uses unleaded solders.
: Pattern from the side which enables seeing.(The other layers patterns are not indicated)
Through hole is omitted.
There are few cases that the part printed on diagram isnt mounted
in this model.
: panel designation
Chip parts.
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face sideseen from
the pattern face are indicated.
Parts on the parts face sideseen from
the parts face are indicated.
-
8/8/2019 Sony Bdp Bx57,s570
64/1325-2
BDP-BX57/S570
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-2.SWB-001 (SWITCH) BOARD PRINTED WIRING BOARD
SWB-001 BOARD
CN401 A-1
A
1 2
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-3.SWP-001 BOARD PRINTED WIRING BOARD- Ref. No.: SWP-001 board; 20,000 series -
SWP-001 BOARD
CN331 A-1
A
1
3 4
SWB-001
SWP-001
CN402 A-2
1-880-457-
1-880-458-
11
11
See page 4-23 for circuit boards location.
See page 4-23 for circuit boards location.
- Ref. No.: SWB-001 board; 20,000 series -
-
8/8/2019 Sony Bdp Bx57,s570
65/132
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-4. FR-310 BOARD (FRONT RIGHT) PRINTED WIRING BOARD- Ref. No.: FR-310 board; 20,000 series -
BDP-BX57/S570
5-3
A
1 2 3 4 5 6 7
B
FR-310 BOARD (SIDE A)
FR-310 BOARD (SIDE A)
CN371 B-7
D702 B-1D705 B-3D706 B-3D707 B-3D709 A-6
IC702 B-5
Q703 B-2Q704 B-2Q706 B-3Q707 B-3Q709 B-1Q710 B-6
A
1 2 3 4 5 6 705
B
C721
FR-310 BOARD (SIDE B)
CN372 B-7CN702 A-2
IC701 B-3
111-880-982-
111-880-982-
See page 4-3 for circuit boards location.
-
8/8/2019 Sony Bdp Bx57,s570
66/1325-4
BDP-BX57/S570
: Uses unleaded solder.
5-5. HU-012 BOARD (USB HUB) PRINTED WIRING BOARD
- Ref. No.: HU-015 board; 20,000 series -
B
1 2 3 4 505
A
HU-015 BOARD (SIDE A)
A
1 2 3 4 505
B
HU-015 BOARD (SIDE B)
HU-015 BOARD (SIDE A)
CN102 B-5CN103 A-1CN104 B-3
D106 B-2D107 B-2D109 B-4D110 B-4D111 B-3
IC102 A-4IC103 A-3
There are a few cases that the part isnt mounted in this model is printed on this diagram.
See page 4-5 for circuit boards location.
CN101
IC104
IC107
D107
D106
CN104
IC103 IC102
D110D111
CN105IC108
CN103
D104D105
IC106IC105
D109
CN102
X101
1-880-558-11
111-880-558-
CN105 A-1
CN101 B-1
X101 B-2
D104 B-1D105 B-1
IC106 A-2IC107 A-3IC108 A-1
IC105 A-4IC104 B-2
-
8/8/2019 Sony Bdp Bx57,s570
67/1325-5
BDP-BX57/S570
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-6. ANT-007 BOARD (ANTENNA) PRINTED WIRING BOARD- Ref. No.: ANT-007 board; 20,000 series -
See page 4-6 for circuit boards location.
PAT201A
105
B
ANT-007 BOARD
(SIDE A)
ANT-007 BOARD
(SIDE B)
A
105
B1-880-559-11
ANT-007 BOARD (SIDE A)
CN201 A-1
111-880-559-
-
8/8/2019 Sony Bdp Bx57,s570
68/1325-6
BDP-BX57/S570
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-7. ANT-008 BOARD (ANTENNA) PRINTED WIRING BOARD- Ref. No.: ANT-008 board; 20,000 series -
See page 4-7 for circuit boards location.
A
105
B
ANT-008 BOARD
(SIDE A)
ANT-008 BOARD
(SIDE B)
1-880-560-
11
A
1 05
B1-880-560-
11
ANT-008 BOARD (SIDE A)
CN301 A-1
CN301
PAT301
-
8/8/2019 Sony Bdp Bx57,s570
69/132
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-8. MB-134 BOARD (MAIN) PRINTED WIRING BOARD (SIDE A)
See page 4-8 for circuit boards location.
- Ref. No.: MB-134 board; 10,000 series -
A
B
C
D
E
F
G
H
1 2 543 6
BDP-BX57/S570
5-7
MB-134 BOARD (SIDE A)
CN301 B-6
CN601 C-2
CN602 C-2
CN701 G-3
CN1401 D-1
CN1502 C-6
CN1503 G-1
CN1504 A-2
CN1509 C-6
D303 B-2
D304 C-6
D901 F-5
D904 G-4
D905 G-5
IC105 C-5
IC204 D-5
IC205 E-5
IC901 G-5
IC904 G-1
I C1 00 2 F -4
I C1 00 3 F -4
I C1 45 1 E -1
I C1 50 3 A -4
I C2 30 1 B -1
Q901 G-1
Q1502 A-4
CN1102 E-6
CN2460 C-1
CN2470 B-1
IC104 C-5
-
8/8/2019 Sony Bdp Bx57,s570
70/132
A
B
C
D
E
F
1 2 543 6
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
- Ref. No.: MB-134 board; 10,000 series -
7
5-8
MB-134 BOARD (SIDE B)
D302 B-2D601 E-2
D602 D-2
IC301 B-2IC303 D-6IC304 C-7IC305 C-6
IC308 B-2IC309 E-2IC310 A-2IC311 B-2
IC312 F-3IC601 E-2IC602 E-2
IC704 D-7IC705 E-6IC1001 C-6IC1201 F-3
IC1501 F-7IC2401 B-5
Q301 B-1
Q302 F-3
Q303 F-3Q702 D-7
BDP-BX57/S570
5-9. MB-134 BOARD (MAIN) PRINTED WIRING BOARD (SIDE B) See page 4-8 for circuit boards location.
-
8/8/2019 Sony Bdp Bx57,s570
71/1325-9
BDP-BX57/S570
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-10. EM-002 BOARD (CONNECTOR) PRINTED WIRING BOARD- Ref. No.: EM-002 board; 20,000 series -
See page 4-24 for circuit boards location.
A
1 205B
EM-002 BOARD (SIDE A)
11
A
12
05 B
EM-002 BOARD (SIDE B)
EM-002 BOARD (SIDE A)
CN402 A-1CN403 A-2
1-881-867-111-881-867-
-
8/8/2019 Sony Bdp Bx57,s570
72/1325-10E
BDP-BX57/S570
There are a few cases that the part isnt mounted in this model is printed on this diagram.
: Uses unleaded solder.
5-11. USB-024 BOARD (REAR USB) PRINTED WIRING BOARD- Ref. No.: USB-024 board; 20,000 series -
See page 4-24 for circuit boards location.
A
1 2
05B
USB-024 BOARD (SIDE A)
11
A
1205B
USB-024 BOARD (SIDE B)
USB-024 BOARD (SIDE A)
CN361 A-1
1-880-983-
CN362 B-2
1-880-983-11
-
8/8/2019 Sony Bdp Bx57,s570
73/132
IC PIN FUNCTION DESCRIPTION
MAIN SYSTEM CONTROL PIN FUNCTION (MB-134 BOARD IC101: CXD9983GG/CXD9984GG)
Pin Symbol Type Description
A1 FESFDO I/O Serial Data Input to Front_End Serial Flash
A3 VOUTD1 I/O NC
A5 VOUTD5 I/O NC
A7 VOUTD9 I/O NC
A9 VOUTD12 I/O NC
A11 VIND0 I/O NC
A13 VIND12 I/O NC
A15 VIND16 I/O NC
GPIO
START-BIT
A19 SPDIF I/O SPDIF Digital Audio Out
A21 SPBCK I/O SPDIF in Bit Clock
A23 AVDD12_27 MPLL Power 1.2V Analog Power for PLL
A25 NS_XTALI O 27MHz Crystal Out
A27 CH1_M Analog HDMI TX data 1 differential pair (M)
A29 CLK_M Analog HDMI TX clock differential pair (M)
A31 DACOUT4 Analog DAC Output
A33 DACOUT1 Analog DAC Output
A35 VCLK I/O VFD Clock (IF_SCK)
RS232 RX
CPU_UARXD
A39 ETRXD3 I/O Receive Data from the PHY
A41 ETRXD0 I/O Receive Data from the PHY
A43 ETRXCLK I/O Receive Clock from the PHY
B2 FESFCS I/O Front-END Serial Flash Chip Select
B4 VOUTD3 I/O NC
B6 VOUTD7 I/O NC
B8 VOUTD10 I/O NC
B10 VOUTD14 I/O NC
GPIO
DAC_XRST
B14 VIND14 I/O NC
B16 VINHSYNC I/O NC
GPIO
USB_VBUS_PCONT2
B20 SPLRCK I/O SPDIF in Left-Right Clock
B22 AOBCK I/O Audio Out Bit Clock
B24 AVDD12_DMPLL Power 1.2V Analog Power for DMPLL
B26 CH2_M Analog HDMI TX data 2 differential pair (M)
B28 CH0_M Analog HDMI TX data 0 differe