Download - Solutions and Concentration (p123 -136 )
Solutions and Solutions and Concentration (p123 -Concentration (p123 -136)136)Lesson 2 Dec 7th – 8th
Homework from MondayHomework from MondayP 276 figure 6- predict solubility, p 269 # 8, p 271 # 4, 5, 6, p 277 # 4,5, p 279 # 9-12, p280 # 2-4
Concentration of Concentration of solutionssolutionsThe concentration of a solution is
the ratio of the quantity of solute to the quantity of solution.
Whenever possible, reactions are carried out with all of the reactants in the same fluid phase.
Liquids with liquids and gases with gases.
Types of solutionsTypes of solutions
Dilute solution - ratio of solute to solvent is very small. ◦Example - a few crystals of sugar in a
glass of water. Concentrated solution the ratio of
solute to solvent is large. ◦Example - Maple syrup is a concentrated
solution of sugar in water.
Saturated solution - no more solute can be dissolved in the solvent at a particular temperature.
Unsaturated solution - the ratio of solute to solvent is lower than that of the corresponding saturated solution. If more solute is added to an unsaturated solution, at least some of it should dissolve
Supersaturated solution is an unstable system in which the ratio of dissolved solute to solvent is higher than that of a saturated solution. A supersaturated solution can be made by gently cooling a hot saturated solution.
At a lower temperature the dissolved solute can be made to precipitate out when a seed crystal is added. The process is called precipitation and the substance that forms is the precipitate.
Supersaturated Supersaturated solutionsolution
The amount of solute needed to make a saturated solution in a given quantity of solvent at a specific temperature is called the solubility of the solution.
ConcentrationsConcentrations
There are 3 basic ways to express concentration
1.Percent concentration2.Very low concentrations 3.Molar Concentrations
Percent Concentration Percent Concentration Can be expressed in V/V (volume
by volume), W/W (weight by weight) or W/V (weight by volume)
Volume by volume (V/V) Volume by volume (V/V) concentration – 2 liquids concentration – 2 liquids Example 1Example 1
What is the % V/V if 30 mL of pure ethanol is added to 250 mL of water?
vsolute = 30 mL
vsolution = 250 mL + 30 mL = 280
mL
csolution = ?
csolution = vsolute x 100%
vSolution
csolution = 30 mL X 100%
280 mL
csolution = 10.7 % V/V
Therefore, 30 ml of ethanol dissolved in 250 ml of water is a 10.7% solution.
Weight by volume (W/V) Weight by volume (W/V) concentration – liquid and solid concentration – liquid and solid Example 2Example 23 grams of H2O2 topical antibiotic
solution is dissolved into 50mL of solution. What is the w/v concentration?
mH2O2 = 3 g
vsolution = 50 mL
csolution = ?
csolution = msolute x 100%
vSolution
csolution = 3 g x 100%
50 ml
csolution = 6 % solution
Therefore, the solution has a mass by volume concentration of 6%.
Weight by weight (W/W) Weight by weight (W/W) concentration – Example 3concentration – Example 3What is the % W/W of copper in an alloy
when 10 g of Cu is mixed with 250 g of Zn?
mCu= 10 g = solute
mZn = 250 g + solute = 260
g Concentration = ?
c = msolute x 100%
msolution
Concetration = 10 g Cu x 100% 260 g
csolution = 3.8 % solution
Therefore the alloy has a percent concentration of 3.8 % copper.
Page 284 # 2-8
VERY LOW VERY LOW CONCENTRATIONSCONCENTRATIONS
Very low concentrations are expressed in parts per million
Example 4Example 4Dissolved O2 in water shows a
concentration of 333 mL of water At SATP and 6.5 mg of O2. What is the concentration in ppm?
mO2 = 6.5 mg
look at chart above and see that ppm = 1mg/1L
vH2O = 333mL = 0.333L
cO2 = ?
cO2 = m / v
cO2 = 6.5mg / 0.333 L
= 19.5 ppmTherefore, there are 19.5 parts
of O2 for every million of
water.
Example 5 Example 5 The maximum acceptable
concentration of fluoride ions in municipal water supplies is 1.5 ppm. What is the maximum mass of fluoride ions you would get from a 0.250 L glass of water? cF = 1.5 mg/L
look at chart above and see that ppm = 1mg/1Lratio = 1.5 mg / 1 L = concentration
vH2O = 0.25 L
mF = ?
c = m / v rearrange to m = c x v
Therefore the maximum amount of fluoride ions in 250 ml of water is 0.375 mg.
questionsquestionsPage 287 # 11-17
MOLAR MOLAR CONCENTRATIONS AND CONCENTRATIONS AND MOLARITY MOLARITY
Molar concentration or Molarity, is a way of specifying the amount of solute in one litre of solvent (mol /L). The abbreviated form is M or c. In some cases molar concentration is indicated by using square brackets. [NH3(aq)] = 0.5 mol/L
Example 6 Example 6 In a quantitative analysis, a
stiochiometric calculation produced 0.15 mol of NaOH in a 0.250 mL solution. Calculate the molar concentration of sodium hydroxide.
nNaOH = 0.15 mol
v = 0.250 ml c =?c = n/v
= 0.6 mol/LTherefore, the molar concentration of sodium hydroxide is 0.6 M.
Example 7 Example 7 A student requires 0.250 moles of
NaCl for an experiment. The only thing available to them is a bottle with a solution labelled "0.400 M NaCl." What volume of the solution should be used? Give the answer in millilitres.n = 0.250 mol
c = 0.400 mol/L = 0.400 mol / 1000 mLv = ?v = n / c = 0.625 L
Therefore, the student would need 625 ml of the 0.400mol /L solution.
Example 8 Example 8 How many grams of NaOH would
be needed to produce 500 mL of solution with a molarity of 1 M.
v = 500 mL = 0.5 Lc = 1 mol/Ln = ?
n = 0.5 mol
Now we must find the massm = n x M
m = 20 g.
Example 9Example 9A student is heating water to cook
pasta, they add 25 g of sodium chloride to 1.5 L of water. What is the molar concentration of the salt water?
mNa = 25 g
v = 1.5 LMolar concentration = ?
M = 0.28 mol/L Therefore the molar concentration of the salt water is 0.28 mol/L
Questions Questions Page 290 # 19 – 22 Page 290 # 2 - 8