Download - Soal2 AutoCAD.pdf
-
7/30/2019 Soal2 AutoCAD.pdf
1/19
Figure 1. To make this object, notice the absolute coordinate location of the smallercircle (4,4.5) which is where you are going to start with. And the rest of the object
follows with it.
Figure 2. This object is made with the advantage of the direct distance entrycommand to first make the perimeter (first without the curves). The curves in the
sides can be made by using the filletor circle-ttrcommand then trim.
-
7/30/2019 Soal2 AutoCAD.pdf
2/19
Figure 3. Again notice the absolute coordinate location of the line in 1, 3 and thepoint in 5,7 which is where the rest of the drawing follows.
Figure 4. This object again has absolute coordinates to follow. This is made throughcircles-2P, lines, and ars (start-center-radius).
Figure 5. To make this object, start with the line, then the arcs. The center of thearc in 45 is the endpoint of the location 1.50.
Figure 6. This drawing again has absolute coordinate locations to follow. Thetriangle is made by following those commands given in numbered order. To circle
inside the triangle is made through cicle-ttrcommand.
-
7/30/2019 Soal2 AutoCAD.pdf
3/19
Figure 7. Though this object can be made through lines and arcs, the objective is tomake this one using polylines wherein the lines and arcs are connected.
Figure 8. This object starts with the smaller circles with the diameter or 0.50 andthe rest follows. A circle-ttrcommand is more useful than using arc to make the
curves.
-
7/30/2019 Soal2 AutoCAD.pdf
4/19
Figure 9. This object is almost similar to figure 9 which also starts with the smallercircles. Again a cicle-ttrcommand is used here than arcs to make the curves. Tocopy the arc inside or outside at a different radius, the offsetcommand could be
useful.
Figure 10. In this objects the direct distance entry could be useful to make theperimeter. For the curves on the edge, filletcommand could also be used. Relative
rectangular entry with snap-from command could locate the circles center. Tomake the dash-dot center line you need to load the line in the linetype box.
-
7/30/2019 Soal2 AutoCAD.pdf
5/19
Figure 11. The objective of making this object is to learn the array(rectangular and
polar) command. There are a total of 176 smaller circles. There are 40 circlesaround each inner circles and 96 circles inside.
Figure 12. This exercise will help you use the chamfercommand which will helpyou make the cut on the edge. The mirrorcommand is also used to reflect an
object to its opposite side.
-
7/30/2019 Soal2 AutoCAD.pdf
6/19
-
7/30/2019 Soal2 AutoCAD.pdf
7/19
.
-
7/30/2019 Soal2 AutoCAD.pdf
8/19
-
7/30/2019 Soal2 AutoCAD.pdf
9/19
-
7/30/2019 Soal2 AutoCAD.pdf
10/19
-
7/30/2019 Soal2 AutoCAD.pdf
11/19
-
7/30/2019 Soal2 AutoCAD.pdf
12/19
-
7/30/2019 Soal2 AutoCAD.pdf
13/19
-
7/30/2019 Soal2 AutoCAD.pdf
14/19
-
7/30/2019 Soal2 AutoCAD.pdf
15/19
-
7/30/2019 Soal2 AutoCAD.pdf
16/19
-
7/30/2019 Soal2 AutoCAD.pdf
17/19
-
7/30/2019 Soal2 AutoCAD.pdf
18/19
-
7/30/2019 Soal2 AutoCAD.pdf
19/19