SKID RESISTANCE AND THE EFFECT OF TEMPERATURE
MOHD AMIN BIN SHAFII
A project report submitted in partial fulfillment of the
requirements for the award of the degree of
Master of Engineering (Civil - Transportation and Highway)
Faculty of Civil Engineering
Universiti Teknologi Malaysia
NOVEMBER 2009
V
ABSTRACT
Skid resistance is the force developed when a tire that is prevented from
rotating slides along the pavement surface. It is the most important characteristic of
the road pavement. In the wet conditions, skidding will occur easily when the water
film covering the pavement act as lubricant and reduce the friction between the tire
and pavement. There are several factors that influence skid resistance such as road
pavement texture, aggregate characteristic and surface temperature. Although a
number of researcher have attempted to explain and quantify the effect of
temperature on pavement skid resistance properties, the result are still unclear.
Therefore, the objective of this study is to investigate the effect of pavement surface
temperature on the pavement skid resistance properties of different type of mixtures.
Besides, this study also wants to investigate whether the type of gradation has a
significant effect on skid resistance based on temperature difference. To accomplish
the objectives of the study, five types of mixture consist of ACW 14, ACW 10,
Porous Mix Grade A, Porous Mix Grade B and SMA 14 were prepared. Then, the
skid resistance test using British Pendulum Tester was conducted. The test was
conducted using heated temperature method and natural temperature method. The
results of skid resistance using heated temperature method were compared with the
result of skid resistance using natural temperature method. In this study, it is found
that temperature has a significant effect on skid resistance value and the relationship
between skid resistance value and temperature can be represent using quadratic
curve. Based on temperature different, type of gradation also has significant effect to
the skid resistance value.
vi
ABSTRAK
Rintangan gelinciran adalah daya yang terhasil apabila tayar kenderaan
dihalang daripada berputar. menggelongsor sepanjang permukaan turapan. Rintangan
gelinciran adalah ciri penting bagi turapan jalan. Dalam keadaan basah, kegelinciran
lebih mudah terjadi apabila lapisan air yang menutupi permukaan turapan bertindak
sebagai pelincir yang mengurangkan geseran antara tayar kenderaan dengan turapan
jalan. Terdapat beberapa faktor yang mempengaruhi rintangan gelinciran seperti
tekstur permukaan turapan jalan, ciri-ciri agregate dan suhu permukaan turapan.
Walaupun ramai penyelidik cuba untuk menerangkan kesan suhu terhadap rintangan
gelinciran, tetapi hasilnya masih belum jelas. Oleh itu, kajian ini dijalankan untuk
mengetahui kesan suhu permukaan turapan terhadap rintangan gelinciran bagi
pelbagai jenis campuran. Disamping itu, kajian ini juga dijalankan untuk mengetahui
samada, pada suhu yang berlainan, jenis penggredan aggregat mempengaruhi
rintangan gelinciran atau tidak. Untuk menyempurnakan kajian ini, lima jenis
campuran terdiri daripada ACW 14, ACW 10, Campuran Poros Gred A, Campuran
Poros Gred B dan SMA 14 disediakan. Ujian rintangan gelinciran kemudiannya
dijalankan dengan meggunakan alat British Pendulum Tester. Ujian dijalankan
menggunakan kaedah suhu pemanasan (heated temperature method) dan kaedah
suhu semulajadi (natural temperature method). Keputusan ujian rintangan gelinciran
menggunakan kaedah suhu pemanasan (heated temperature method) kemudiannya
dibandingkan dengan keputusan ujian rintangan gelinciran menggunakan kaedah
suhu semulajadi (natural temperature method). Daripada kajian ini, didapati bahawa
suhu permukaan turapan memberi kesan kepada nilai rintangan gelinciran dan
hubungan antaranya boleh diwakili oleh lengkung kuadratik. Daripada kajian ini
juga, didapati bahawa, pada suhu yang berlainan, jenis penggredan aggregat
mempengaruhi rintangan gelinciran.
vii
TABLE OF CONTENTS
CHAPTER TITLE PAGE
DECLARATION ii
DEDICATION iii
ACKNOWLEDGEMENT iv
ABSTRACT v
ABSTRAK vi
TABLE OF CONTENTS vii
LIST OF TABLES x
LIST OF FIGURES xii
LIST OF APPENDICES xiv
1 INTRODUCTION 1
1.1 Background of Study 1
1.2 Problem Statement 2
1.3 Aim and Objective of the Study 2
1.4 Scope of the Study 3
2 LITERATURE REVIEW 4
2.1 Introduction 4
2.2 Factors Influence Skid Resistance 4
2.2.1 Aggregate Characteristic 5
2.2.2 Road Surface Texture 5
2.2.2.1 Micro texture 6
2.2.2.2 Macro texture 6
2.2.3 Temperature Effects 8
viii
2.2.3.1 Air Temperature 8
2.2.3.2 Tire Temperature 9
2.2.3.3 Pavement Temperature 10
2.2.4 Vehicle Factors 11
2.2.5 Driver Factors 11
2.3 Pavement Tire Friction Theory 12
2.4 Skid Resistance Measurement , 16
2.4.1 Locked Wheel Tester 16
2.4.2 British Pendulum Tester 17
2.4.3 Sideways Force Coefficient Routine
Investigation Machine (SCRIM) 18
2.4.4 Grip Tester 19
3 METHODOLOGY 22
3.1 Introduction 22
3.2 Operational Framework 22
3.3 Preparation Material for Mix 25
3.4 Aggregate Test 25
3.4.1 Sieve Analysis 25
3.4.2 Specific Gravity 29
3.4.2.1 Specific Gravity and Water Absorption
of Coarse Aggregate (> 5.00 mm) 29
3.4.2.2 Specific Gravity and Water Absorption
of Fine Aggregate (<5.00 mm) 30
3.4.3 Theoretical Maximum Density 31
3.5 Bitumen Test 32
3.5.1 Penetration Test 33
3.5.2 Softening Point Test 36
3.5.3 Penetration Index 38
3.6 Determination of Optimum Bitumen Content 40
3.6.1 Asphaltic Concrete (AC) - ACW 10 and ACW 14 40
3.6.1.1 Preparation of Marshall Sample 41
3.6.1.2 Bulk Specific Gravity Measurement 42
3.6.1.3 Marshall Flow and Stability Test 43
3.6.1.4 Voids in Total Mix (VTM)
3.6.1.5 Void Filled with Bitumen
3.6.2 Porous Mix (Grade A and Grade B)
3.6.2.1 Air Void Test
3.6.2.2 Drain-down Test
3.6.2.3 Cantabro Test
3.7 Preparation of Test Sample
3.8 Sand Patch Test
3.9 Skid Resistance Test
4 RESULT AND ANALYSIS
4.1 Introduction
4.2 Aggregate Gradation
4.3 Washed Sieve Analysis
4.4 Specific Gravity and Water Absorption
4.4.1 Coarse Aggregate
4.4.2 Fine Aggregate
4.5 Theoretical Maximum Density
4.6 Bitumen Test Result
4.6.1 Penetration
4.6.2 Softening Point
4.7 Optimum Bitumen Content
4.8 Sand Patch Result
4.9 Skid Resistance Result
5 CONCLUSION AND RECOMMENDATIONS
5.1 Introduction
5.2 Summary of the Findings and Conclusion
5.3 Recommendation
REFERENCES
APPENDICES
XI
LIST OF TABLES
TABLE NO. TITLE PAGE
3.1 Gradation limit for ACW10 26
3.2 Gradation limit for ACW14 27
3.3 Gradation limit for Porous Mix Grade A 27
3.4 Gradation limit for Porous Mix Grade B 27
3.5 Gradation limit for SMA 14 28
3.6 Design Bitumen Content 40
4.1 Gradation limit for ACW10 61
4.2 Gradation limit for ACW 14 61
4.3 Gradation limit for Porous Mix Grade A 62
4.4 Gradation limit for Porous Mix Grade B 62
4.5 Gradation limit for SMA 14 62
4.6 Washed sieve analysis result for ACW 10 63
4.7 Washed sieve analysis result for ACW 14 63
4.8 Washed sieve analysis result for Porous Mix Grade A 63
4.9 Washed sieve analysis result for Porous Mix Grade B 63
4.10 Washed sieve analysis result for SMA 14 64
4.11 Specific gravity of coarse aggregate for ACW 64
4.12 Specific gravity of coarse aggregate for Porous Mix 65
4.13 Specific gravity of coarse aggregate for SMA 65
4.14 Specific gravity of fine aggregate for ACW 66
4.15 Specific gravity of fine aggregate for Porous Mix 66
4.16 Specific gravity of fine aggregate for SMA 67
4.17 Theoretical Maximum Density for ACW 10 68
XI
4.18 Theoretical Maximum Density for ACW 14 68
4.19 Theoretical Maximum Density for Porous Mix Grade A 69
4.20 Theoretical Maximum Density for Porous Mix Grade B 69
4.21 Theoretical Maximum Density for SMA 14 70
4.22 Penetration value for bitumen 80/100 and PG 76 70
4.23 Softening point for bitumen 80/100 and PG 76 71
4.24 Mean texture depth . 72
xii
LIST OF FIGURES
FIGURE NO. TITLE PAGE
2.1 Illustration of terms used to describe roads surface texture 7
2.2 Mechanism of Rubber Friction 14
2.3 Locked Wheel Tester 17
2.4 British Pendulum Tester 18
2.5 Sideways Force Coefficient Routine Investigation Machine
(SCRIM) 19
2.6 Grip Tester 20
3.1 Flow diagram for methodology 23
3.2 Flow diagram for laboratory work 24
3.3 Penetration test 33
3.4 Penetration test samples 34
3.5 Test samples were immersing in water bath at 25 °C 35
3.6 Penetration reading taken 35
3.7 Apparatus for bitumen Softening Point Test 36
3.8 Test sample for softening point test 37
3.9 Nomograph for bitumen penetration index. 39
3.10 Flow and stability test. 45
3.11 Basket used for drain-down test 49
3.12 Sample basket and metal tray before drain-down test 50
3.13 Samples before Cantabro test 51
3.14 Samples after Cantabro test. 52
3.15 Mould for skid test sample 53
3.16 Roller compactor 54
xiii
3.17 Test sample 54
3.18 The apparatus and elements used on Sand Patch Test 55
3.19 Circular area of the sand cover 56
3.20 British Pendulum Tester 57
3.21 Dryer 58
3.22 Water spray 58
3.23 Infrared temperature gun . 59
4.1 Graph of Pendulum Test Value (PTV) versus Temperature
for all types of mixtures using heated temperature method 73
4.2 Graph of Pendulum Test Value (PTV) versus Temperature
for all types of mixtures using natural temperature method 73
4.3 Some of the bitumen is pill out from the sample surface
after skid resistance test 74
xiv
LIST OF APPENDICES
APPENDIX TITLE PAGE
A Marshall Test Result for ACW 10 82
B Marshall Test Result for AC W 14 86
C Air Void Test Result, Drain-down Test Result and
Cantabro Test Result for Porous Mix Grade B 90
D Skid Resistance Test Result 94
CHAPTER 1
INTRODUCTION
1.1 Background of Study
Road accident is a significant problem and a major concern of most highway
agencies. Statistics from Polis Diraja Malaysia (PDRM) show that the number of
road accidents increased almost every year. The number of road accident increased
from 279711 cases in year 2002 to 363319 cases in 2007. Almost 3% of the road
accident involves the fatal accident.
There are several factors that contribute to the road accidents. One of the
factors is skidding. Skid resistance is the most important characteristic of the road
pavement. Skidding will happen when the pavement surface does not provide
adequate friction to the tire. In the wet conditions, skidding will occur easily when
the water film covering the pavement act as lubricant and reduce the friction between
the tire and pavement.
Skid resistance is monitored using different types of skid testing device. The
most commonly used device is locked wheel trailer and British Pendulum Tester
(BPT). Skid tests are subject to many influential factors, which can be generally
classified into three categories: tire-related factors (rubber compound, tread design
and condition, inflation pressure, and operating temperature); pavement-related
factors (pavement type, microtexture and macrotexture, and surface temperature);
2
and intervening-substance-related factors (quantity of water, presence of loose
particulate matter, and oil contaminants).
A number of researchers have investigated the effect of temperature on
pavement skid resistance properties. One of the problems encountered while
reviewing these efforts is that the type of temperature used in these studies has not
been consistent. For example, Runkle and Mahone (1980) considered the maximum,
minimum and average daily temperatures; Burchett and Rizenbergs (1980)
considered the maximum and minimum air temperature during a four to eight - week
period; and the National Safety Council (1975) used the pavement surface
temperature to correlate with pavement friction. Furthermore, the investigations
conducted so far have not produced consistent results. While some researchers
Runkle and Mahone (1980), Burchett and Rizenbergs (1980), indicated a statistically
significant effect of air or pavement temperature on the skid properties, others
Mitchell et al., concluded that the effect was insignificant.
1.2 Problem Statement
Environmental factor such as temperature is believed to affect the skid
resistance properties of the pavement. Although a number of researcher have
attempted to explain and quantify the effect of temperature on pavement skid
resistance properties, the result are still unclear.
1.3 Objectives of Study
The objective of this study is to investigate the effect of pavement surface
temperature on the pavement skid resistance properties of different type of mixtures.
Besides, this study also wants to investigate whether the type of gradation has a
significant effect on skid resistance based on temperature difference. To accomplish
the objectives of the study, several tests were conducted using asphaltic concrete
3
wearing (ACW) mixture, porous asphalt and stone mastic asphalt (SMA). The tests
were conducted at several temperatures.
1.4 Scope of Study
This study only limited to laboratory test and not consider field test. The
temperature variable only considers pavement surface temperature (sample
temperature).
CHAPTER 2
LITERATURE REVIEW
2.1 Introduction
In general, the highway surface should have some sort of roughness to
facilitate friction between the car wheel and pavement surface. Adequate surface
friction must be provided on a pavement, so that loss of control does not occur in
normally expected situations when the pavement is wet (Huang, 2004). Skid
resistance is the force developed when a tire that is prevented from rotating slides
along the pavement surface. Skid resistance is a measure of the resistance of the
pavement surface to sliding or skidding of the vehicle. It is a relationship between the
vertical force and the horizontal force developed as a tire slides along the pavement
surface. Therefore, the texture of the pavement surface and its ability to resist the
polishing effect of traffic is of prime importance in providing skidding resistance.
2.2 Factors Influence Skid Resistance
The skid resistance of a pavement is dependent upon a number of factors such
as:
i. Aggregate characteristic
ii. Road surface texture
5
iii. Temperature (air, tire, pavement)
iv. Vehicle factors
v. Driver factors
2.2.1 Aggregate Characteristic
The aggregate properties which have direct influence on skid resistance are
the type, size (gradation), shape and the resistance to the polishing wear (Ludema
and Gujrati, 1973). The texture of the aggregate, especially the coarse aggregate
contributes to the skid resistance of the pavement. The use of varying amounts of
coarse and fine aggregates will influence the skid resistance. For normal bituminous
paving, the larger aggregate sizes govern the skid resistance. The skid resistance of
aggregates is actually the polishing resistance of the aggregate.
High speed and high traffic can polish the aggregate, leading to a smooth
surface and a reduction in the pavement skid resistance. Aggregates specified for
wearing courses for roadways or highways must possess some resistance to
polishing. The polish stone value (PSV) is a measure of the resistance of the coarse
aggregate to the polishing action of a vehicle's tire under conditions that are similar
to those occurring on the pavement surface. The higher the polished stone value, the
more resistant the aggregate is to polishing (Lavin, 2003).
2.2.2 Road Surface Texture
Pavement surface texture greatly contributes to the tire pavement skid
resistance. Pavement surface irregularities are continuous from pavement
macrotexture to pavement microtexture. Skid resistance is highly dependent on the
surface irregularities of individual stone particles used in pavements and upon the
larger irregularities of the overall road surface. The surface irregularity of individual
particles is referred to as "fine-scale" or "microtexture". "Coursescale" or
6
''macrotexture" refers to the larger irregularities found between the particles that
make up the pavement. Microtexture and macrotexture are the heavy hitters for skid
resistance.
2.2.2.1 Microtexture
Microtexture refers to the small-scale texture of the pavement aggregate
component which controls contact between the tire rubber and the pavement surface.
Microtexture depends on surface properties of the aggregate particles contained in
the paving material and is mainly responsible for pavement friction at low speeds.
Therefore, it is produced from the coarse aggregate. When the exposed aggregate
becomes polished due to traffic use, the road surface can become slippery.
2.2.2.2 Macrotexture
Macrotexture refers to the large-scale texture of the pavement as a whole due
to the aggregate particle arrangement which controls the escape of water under the
tire and hence the loss of skid resistance at high speeds. Macrotexture is influenced
by the properties of the paving mixture and the method of finishing or texturing of
the surface. Macrotexture helps reduce the potential for separation of tire from
pavement surface due to hydroplaning and induce friction for vehicles travelling at
high speeds. Therefore, macrotexture is controlled by the shape, size, gap width,
layout, and gradation of the coarse aggregates.
REFERENCES
Anderson D. A., W. E. Meyer, and J. L. Rosenberger (1984) "Development of a
Procedure for Correcting Skid-Resistance Measurements to a Standard End-
of-Season Value." Transportation Research Record, No. 1084, 40-48p.
British Standard Institution (2003). BS EN 13036-4. Method for measurement of
slip/skid resistance of a surface-The pendulum test. London: British Standard
Institution.
Burchett J. L and R. L. Rizenbergs (1980) "Seasonal Variations in the Skid
Resistance of Pavements in Kentucky." Transportation Research Record, No.
788, 12p.
Chua Sy Szu (2008). Effect of Elastomeric Base Waste on Hot Mix Asphalt. Bachelor
of Civil Engineering, Universiti Teknologi Malaysia, Skudai.
Dahir S. H., J. J. Henry and W. E. Meyer (1979) "Final Report: Seasonal Skid
Resistance Variations." Pennsylvania Department of Transportation,
Harrisburg.
Do, M.T., Tang Z., Kane M. and F. de Larrard (2008). Evolution of Road-surface
Skid-resistance and Texture due to Polishing. Elsevier. B. V. 2008.04.060
79
Elkin B. L., K. J. Kercher and S. Gulen (1980) "Seasonal Variation in Skid
Resistance of Bituminous Surfaces in Indiana." Transportation Research
Record, No. 777, 50-58p.
Fenech R. (2000). The Influence of Mixture Composition on the Skidding Resistance
of Asphalt Wearing Courses. Faculty of Architecture and Civil Engineering,
University of Malta.
Gunaratne M., Bandara N., Medzorian J., Chawla M. and P. Ulrich (2000).
Correlation of Tire Wear and Friction to Texture of Concrete Pavements.
Journal of Materials In Civil Engineering. Paper No. 16150.
Hill B.J. and J. J. Henry (1982) "Surface Materials and Properties Related to
Seasonal Variations in Skid Resistance." ASTM STP 763, 5p.
Hill B.J. and J. J. Henry (1982) "Mechanistic Model for Predicting Seasonal
Variations in Skid Resistance." Transportation Research Record, No. 946, 29-
37p.
Hosking J. R. and G. C. Woodford (1976) "Measurement of Skid Resistance Part II,
Factors Affecting the Slipperiness of a Road Surface", Transportation Road
Research Lab (U.K.), Report LR 346
Huang, Y. H. (2004). Pavement Analysis and Design. (2nd ed.) Upper Saddle River,
N. J.: Prentice Hall.
Ibrahim M. Asi (2007). Evaluating skid resistance of different asphalt concrete
mixes. Building and Environment, 42, 325-329. Elselvier Ltd.
Jayawickrama P. W. and B. Thomas (1997) "Correction of Field Skid Measurements
for Seasonal Variations in Texas." Transportation Research Record, No.
1639, 2p
80
Kummer H. W. and W. E. Meyer (1962) "Measurement of Skid Resistanc,
Symposium on Skid Resistance." ASTM Special Technical Publication, No.
326,3-28p.
Lavin, P. (2003). Asphalt Pavement: A Practical Guide to Design , Production and
Maintenance for Engineers and Architects. New Fetter Lane, London.: Spon
Press.
Ludema, K. C. and Gujrati, B. D. (1973). An Analysis of the Literature on Tire-road
Skid Resistance. Philadelphia.: American Society for Testing and Materials.
Meyer W. E. (1968) "Friction and Slipperiness." Highway Research Record No. 214,
13-17p.
Mitchell, J.C., M.I. Phillips, and G. N. Shah (1986) "Report No. FHWA/MD-86/02:
Seasonal Variation of Friction Numbers." Maryland Department of
Transportation (MDOT), Baltimore.
Mohd Khairumfithri Bin Abdul Rahim (2008). Perbandingan Kesan Perpalohan
Terhadap Campuran Panas Asfalt Dengan Menggunakan Mini Test Track.
Bachelor of Civil Engineering, Universiti Teknologi Malaysia, Skudai.
Oliver, J.W.H. (1989) "Seasonal Variation of Skid Resistance in Australia."
Australia Road Research Board, Special Report No. 37.
Runkle S. N. and D. C. Mahone (1980) "Variation in Skid Resistance over Time."
Virginia Highway & Transportation Research Council, 10-13p.
Subhi M. Bazlamit, Farhad Reza (2005). Changes in Asphalt Pavement Friction
Components and Adjustment of Skid Number for Temperature. Journal of
Transportation Engineering, Vol. 131.ASCE.
81
Takino, H., et al. (1998) "Effect of Cohesion Loss Factor on Wet Skid Resistance of
Tread Rubber." Tire Science and Technology, TSTCA, Vol. 26, No. 4, 258-
276p.
Yingjian Luo (2003). Effect of Pavement Temperature on Frictional Properties of
Hot-Mix-Asphalt Pavement Surfaces at the Virginia Smart Road. Master of
Science, Virginia Polytechnic Institute and State University, United State of
America.
Zanariah Binti Abd Rahman (2006). Evaluation on Properties of Tender Mixes.
Master of Engineering (Civil - Highway and Transportation), Universiti
Teknologi Malaysia, Skudai.