Bekolay & Associates Ltd. Ph: 613-723-0474 2018-04-13
200-1827 Woodward Drive, Ottawa Email:[email protected]
Shop Drawing Review Comments
Consultant: Barry J. Hobin & Associates Architects 63 Pamilla St. Ottawa On. K1S 3K7
Project: Boys & Girls Club P.O.W. 1463 Prince of Wales
Contractor: Tal-Co BAL No.: 2017-17
Attn: Doug van den Ham
Sandy Davis Date: 2018-04-13
Mech Shop Drawing Review Comments
1. General: The documents in the list have been examined for general conformance with the Contract Documents prepared by
Bekolay & Associates Ltd. (BAL) for this project. This review may not be extended to any other contract, trade, division or
project. Review by BAL does not imply approval or verification of information presented in these drawings and the
responsibility for installation and performance lies solely with the Contractor submitting the documents including
dimensional conformance and co-ordination with other trades. All changes, comments and notes by BAL shall be
incorporated (at no cost to the Owner) into actual installation when indicated “Reviewed As Follows” or be included in a
re-submission (when requested).
2. Shop Drawings: submitted in the attached files
Item Description Submitted File Comments
2.1 Washing Machine box RESUB Boys & Girls Club Reno. Prince Of Wales.pdf
Reviewed, see 3.1
2.2 Lavatories L-1 Ditto Reviewed, see 3.2
2.3 Kitchen Sink KS-1 Ditto Reviewed, see 3.3
2.4 Kitchen Sink KS-2 Ditto Reviewed, see 3.4
2.5 Hand sink Ditto Reviewed, see 3.5
2.6 Water Closet WC-1 Ditto Reviewed, see 3.6
2.7 Mop Sink Ditto Reviewed, see 3.7
2.8 Floor Drain Ditto Reviewed, see 3.8
2.9 Urinal Ditto Reviewed, see 3.9
2.10 Water Closet WC-2 Ditto Reviewed, see 3.10
2.11 SGL Laundry Tub Ditto Reviewed, see 3.11
(Con’t)
Bekolay Gamble & Associates Ltd. Ph: 613-723-0474 2018-04-13
200-1827 Woodward Drive, Ottawa Email: [email protected]
3. Additional Notes:
3.1. No comment, prior submission, reviewed (2018-03-09)
3.2. No comment, prior submission, reviewed (2018-03-09)
3.3. No comment, prior submission, reviewed (2018-03-09)
3.4. No comment, prior submission, reviewed (2018-03-09)
3.5. No comment, prior submission, reviewed (2018-03-09)
3.6. No comment, prior submission, reviewed (2018-03-09)
3.7. No comment, prior submission, reviewed (2018-03-09)
3.8. No comment, prior submission, reviewed (2018-03-09)
3.9. No comment, prior submission, reviewed (2018-03-09)
3.10. No comment
3.11. No comment
For Residential and Commercial ApplicationsES-2-M2-DWB
Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––
Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––
Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. –––––––––––––––––––––––––––––––––––
Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––
2M2 DWB
2M2 DWB Rough-In Kit
2M2 DWB Finish Kit
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
2M2 DWB Rough-In Kit-BR
Series 2M2 DWBDuo-Clozure™ Washing MachineShutoff ValvesSize: 1⁄2" (15mm)Series 2M2 DWB Duo-Clozure™ Washing Machine ShutoffValves consist of a molded plastic enclosure with top and sideknockouts that accept the hot and cold water supply piping aswell as a 11/2" and 2" (40 and 50mm) drain knockout to accom-modate the waste drain pipe. The Duo-Clozure™ incorporates aWatts Model 2M2 Duo-Cloz™ washing machine shutoff valvethat simultaneously controls the flow of both hot and cold waterto the appliance. The Duo-Clozure™ trim plate can be decorat-ed to blend in with the wall finish. The Series 2M2’s ball-typedesign allows it to be opened to any position to throttle waterflow and minimize harmful water hammer and banging pipescaused by fast closing washing machine solenoid valves.
Features
• Decorative white faceplate that can be painted or papered tomatch wall décor
• Used to manually eliminate water pressure on supply hosesand prevent catastrophic water damage
• Connects to 11/2" or 2" (40 or 50mm) drain piping
• Side or top water supply piping
• Supplied with water pressure test plugs
• Easy to install. Models 2M2 DWB and 2M2 DWB Rough-InKit-BR. Complete with adjustable stud mounting brackets
Models
2M2 DWB Size 1/2" (15mm) ell solder con-nections for concealed piping. Contains all of the components fora complete installation.
2M2 DWB Rough-In Kit Contains components to rough-inand test piping and drain system
2M2 DWB Rough-In Kit-BR Contains components to rough-inand test piping and drain systemwith brackets
2M2 DWB Finish Kit Contains the 2M2 washing machineshutoff valve and finish trim
ES-2-M2-DWB.qxd 1/9/08 7:36 AM Page 1
WASHING MACHINE BOX
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Dimensions — Weights
MODEL DIMENSIONS (APPROX.) WEIGHT
A A1 A2 A3 B B1 B2 Min. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs. kg
2M2DWB 63/16 158 6 153 53/16 132 103/16 259 77/32 183 65/8 168 721/32 195 21/2 64 3 1.4
Top View Front View Side View
Finished Wall
M
A2
A1
A
B2 B
B1
A3
ES-2-M2-DWB 0802 ©Watts Regulator Company, 2008
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
W a t e r S a f e t y & F l o w C o n t r o l P r o d u c t s
Typical Installations
41" min.to bottomof bracket
42" min.to box centerline
Duo-Clozure wall box supplied withadjustable stud mounting brackets foreasy installation.2M2 DWB and2M2 DWB Rough-In Kit BR
Duo-Clozure wall box roughed in with decorative faceplate installed.
SpecificationsThe contractor shall install a single-handle wash machine shut-off valve. The ball-type valve shall simultaneously control theflow of both hot and cold water to the appliance and be fittedin a decorative recessed wall box. The decorative wall box shallhave a provision for 11/2 inch and 2 inch (40 and 50 mm) drainpiping and a decorative cover.
The valves shall be a Watts Series 2M2 DWB Duo-Clozure™
Washing Machine Shutoff Valve.
Pressure — TemperatureMaximum Pressure: 150psi (10.3 bar)
Maximum Temperature: 180°F (82°C)
ES-2-M2-DWB.qxd 1/9/08 7:36 AM Page 2
WASHING MACHINE BOX
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
MEZZO™SEMI-COUNTERTOP SINK
FIRECLAY
MEZZO SEMI - COUNTERTOP SINK• Space saving design installs on a minimum
countertop depth of 13”• Fireclay china• Rear overflow• Recessed self-draining deck• Barrier-free design• Self rimming with sealant• Cutout template and mounting kit provided(Faucet shown not included)
❏ 9960.803faucet holes on 203mm (8”) centers (Illustrated)
❏ 9960.403faucet holes on 102mm (4") centers
❏ 9960.001center hole only
Nominal Dimensions:22" (559mm) wide, 21-1/2" (546mm) deepBowl sizes:19" (482mm) wide, 15” (381mm) front to back,6-7/8" (175mm) deep
Fixture Dimensions conform to ANSI Standard A112.19.9M
Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.9M for Non-Vitreous China Fixtures• CAN/CSA B45 series• A1995 National Building Code, section 3.7 andCAN/CSA-B651-02 and OBC 3.8
To Be Specified
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies & Stops:
❏ Trap 1-1/4" (32 mm):
NOTES:DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND "P" TRAP ARE SUG-GESTED.FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE TEM-PLATE SUPPLIED WITH SINK.These measurements are subject to change or cancellation. No responsibility isassumed for use of superseded or voided pages.
* See faucet section for additional models available
19"(482mm)
1-3/8" (35mm) Dia.1 Hole for CHO
9960 0011-3/8" (35mm) Dia. 3 Holesfor 8" (203mm) centres9960 803
1-1/4" (32mm) Dia. 3 Holesfor 4" (102mm) centres9960 403
2-3/4"(70mm)
8"(203mm)
22"(559mm)
4"(102mm)
8"(203mm)
15"(381mm)
21-1/2"(546mm)
Countertop
10-1/2"(267mm)
11"(279mm)
13" min.(330mm)
10-1/2"(267mm)
2-1/2"(64mm)
10-1/2"(267mm)
(cut out size)
CountertopBy Others
Finished Floor
FinishedWall
8-1/4"(210mm) 6"
(152mm)
34"(864mm)
IN ONTARIO33"
(838mm)
1-3/8"(35mm)
4-3/8"(111mm)10-5/8"
(270mm)
12-7/8"(327mm)
1-1/4 O.D.WASTE
SUPPLY
SCREWNUTFLAT WASHER
#10 SCREW
MOUNTING BRACKET
COUNTERTOP - BY OTHERS
WATERPROOFBASIN
© 2002 American Standard Inc.
LAV-000SPS 9960
Top of front rim mounted 864mm (34") from finished floor.MEETS THE AMERICAN DISABILITIES ACT GUIDE-LINES AND ANSI A117.1 ACCESSIBLE AND USEABLEBUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Revised 9/02
BARRIER FREE
White
L-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
L
Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation.Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability.
DSP–DEMD-100 Rev. H
DEMD SeriesElectronic Lavatory Faucets (Infrared)
Note: Measurements may vary ± 6mm (0.25")
Refer to www.specselect.com for individual models. Note: Use this page as a product submittal sheet.
113 mm(4.46")
486 mm(19.13")
65 mm(2.56") 38 mm (1.50") MAX.
DECK THICKNESS
RED/BLUE TEMPERATURE INDICATORS ON NON-REMOVABLE EXTERNAL MIXER HANDLE
O-RING TO SEAL FAUCET TO DECK
175 mm(6.89")
116 mm(4.55")
DECK
32º
SENSOR, ELECTRONICS AND BATTERY
For above deck mounted sinks, the sensor requires a clearance.
For sensor clearance:
38 mm (1.5”) maximum sink lip height from deck.
SENSOR CLEARANCE
DEMD-111LF (BATTERY OPERATED WITH USER MIX)SPECIFICATION: (example)• Deck mount electronic lavatory faucet• Sensor detects user’s hand to activate
water flow• One 9V lithium battery inside spout (included)• Above deck battery and electronics• Red light indicator blinks when battery is low• Vandal resistant (wrench flat)• 0.5 gpm (1.9 L/min) spray outlet
DEMD-111 SERIES• Electronic faucet with mixer to adjust
temperatureo DEMD-111LF (Chrome)o DEMD-111LF-NS (Nickel Stainless)
OPERATIONSensing Range: • Factory set to 8.0" ± 1.5" (200 mm ± 40 mm)• Adjustable from 3.15" to 11.8" (80 mm to
300 mm) with optional remote controlMaximum Run Time: • 90 seconds, adjustable with remote con trol
OPTIONAL ACCESSORIES (Order Separately)
o 060967A• Remote Control – allows adjustment of
sensor range, maximum run time, delayedclose time, temporary shut-off for cleaningand factory settings reset
o 063256A (Chrome Only)• 0.35 gpm (1.32 L/min) spray outlet
o 060961A (Chrome)o 060961ANS (Nickel Stainless)
• 1.0 gpm (3.8 L/min) aerator
o 061118A (Chrome)o 061118ANS (Nickel Stainless)
• 1.5 gpm (5.7 L/min) Careguard®
laminar outlet
2.5
2
1.5
1
.5
000
1
2
3
4
5
6
7
8
9
10 20 30 40 50 60 70 80
STANDARD
OPTIONAL
OPTIONAL
OPTIONAL
Line Pressure (psig)
FLOW(L/min.)
FLOW(GPM)
FLOW RATE vs PRESSURE
Outlet Flow Rates
Approvals:• IAPMO certified• Complies to ASME A112.18.1/CSA B125.1• Indicates compliance to
ICC / ANSI A117.1• Verified compliant with 0.25% weighted average Pb
content regulations(Contact Delta Representative for State and/or Local Approvals.)
HARDWIRE CONVERSION OF DEMD-100 SERIES
A One 060958A DEMD plug in power supply, output 9VDC
plusOne 061168A connector kit
B One 060704A hardwire 20VA transformer (120VAC to 24VAC)
plus One 060974A DEMD converter (24VAC to 9VDC)
plusOne 061168A connector kit
Requires SEPARATE order of either:
OR
L-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Description:OFFSET LAVATORY DRAIN P.O. SHALL BE SUPPLIED WITH 19 HOLE GRID PAT-TERN, CHROME FINISH, CAST BRASS, 17 GAUGE 1-1/4” X 8-3/8” BRASS TAIL-PIECE, LOCKNUT, HEAVY RUBBER GASKET, CERTIFIED BY CSA
Oakville Stamping and Bending Ltd.2200 Speers Road. Oakville, ON. Canada. L6L 2X8.
T. 905.827.0320 or toll free 1.877.314.6040 F. 905.827.6375 or toll free 1.877.827.6040.
All rights reserved. OS&B™ reserves the right to change product specifications and material or discontinue models without notice.
www.osb.ca
3700WCP.O PLUG - OFFSET OPEN GRID
Certification
114"
32mm
514"
132mm
838"
213mm
218"
55mm
238"
59mm
Top View
L-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Description:P-TRAP SHALL BE 1-1/4” GROUND JOINT, 20 GAUGE TUBULAR BRASS, 7”BRASS WALLBEND, CHROME FINISH, BRASS NUTS, DEEP BELL FLANGE,LESS CLEANOUT,CERTIFIED BY CSA
Oakville Stamping and Bending Ltd.2200 Speers Road. Oakville, ON. Canada. L6L 2X8.
T. 905.827.0320 or toll free 1.877.314.6040 F. 905.827.6375 or toll free 1.877.827.6040.
All rights reserved. OS&B™ reserves the right to change product specifications and material or discontinue models without notice.
www.osb.ca
110BDCP1-1/4” 20GA P-TRAP, LESS CLEANOUT
Certification
114"
32mm
10"254mm
114"
32mm43
8"
112mm
L-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
L-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
DROP IN SINK: LBD7508P-1LBD7508P-1 | 2000102007
Double compartment self rimming drop-in sink with faucet ledge. 18 gauge (1.2 mm), type 304 (CNS 18/10),18-10 stainless steel.Exposed surfaces are #4 satin finished. Undercoated to reduce condensation and resonance. Includes waste fittings, factory applied rimseal, cutout template, and factory installed EZ TORQUE™ fasteners. Certified to ASME A112.19.3-2008 / CSA B45.4-08. Center back waste location. Includes 3 1/2" (89 mm) crumb cup strainer with 1 1/2" (DN38) brass tailpiece. Sink has Spillway® partition.
Model Options: LBD7508P-1/1, 1 faucet hole, 1 1/2" diameterLBD7508P-1/3, 3 faucet holes, 1 1/2" diameter, 4" centers, 8" centersetLBD7508P-1/4, 4 faucet holes total, 1 1/2" diameter, 4" centers, 8" centerset, plus 1 faucet hole 4" to the rightLBD7508P-1, Custom (non-returnable)
TECHNICAL DATA
type of basin Double Compartment
bowl depth 8''
Bowl finish satin finished
Bowl front to back 17''
Bowl left to right 15''
gross weight 10.58 kg
material stainless steel
material code 1.4301 Chrome Nickel steel V2A
material thickness grade 18 gauge (1.2 mm)
Overall front to back 22''
Overall left to right 33 1/4''
overflow no
spillway yes
faucet ledge yes
type of waste kit 3 1/2" crumb cup strainer
undercoated yes
waste hole position centre back
PROJECT INFORMATIONItem Location
Project
Number
Quote Number
Notes
Engineer’s Approval
Franke Commercial Systems | [email protected] | www.franke-commercial.com | 2016-06-22
KS-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
net weight 7.86 kg
Franke Commercial Systems | [email protected] | www.franke-commercial.com | 2016-06-22
KS-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Description:P-TRAP SHALL BE 1-1/2” GROUND JOINT, 20 GAUGE TUBULAR BRASS, 20GAUGE 7” WALLBEND, ROUGH BRASS FINISH, BRASS NUTS, LESS FLANGE,LESS CLEANOUT,CERTIFIED BY CSA
Oakville Stamping and Bending Ltd.2200 Speers Road. Oakville, ON. Canada. L6L 2X8.
T. 905.827.0320 or toll free 1.877.314.6040 F. 905.827.6375 or toll free 1.877.827.6040.
All rights reserved. OS&B™ reserves the right to change product specifications and material or discontinue models without notice.
www.osb.ca
114BRBLF1-1/2” 20GA P-TRAP, LESS CLEANOUT
Certification
1012"
267mm
112"
38mm5"
127mm
KS-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
CCOOMMPPLLIIEESS WWIITTHH::• ASME A112.18.1/ CSA B125.1
Indicates compliance toICC/ANSI A117.1
KITCHEN FAUCETS� Signature® Pull-Out Series� Single Handle Deck Mount� Single or 3 Hole Sink Applications
Submitted Model No.: _______________________________________________Specific Features: __________________________________________________
STANDARD SPECIFICATIONS: • Single handle kitchen faucets for exposed mounting onsingle and three hole sinks.
• Centermount or 8" (203 mm) centers with optionalincluded 10 3/4" (273 mm) long escutcheon.
• 8" (203 mm) high, 9" (229 mm) long spout [includes 61/4 (159 mm) long pull-out spray] nestled in all metal hub assembly, swings 120°.
• Spout is connected to valve body with a 53" (1346 mm)long hose that extends to 34" (864 mm) usable length.
• Pull-out spout operates in an aerated or spray modevia an easy side-to-side push lever.
• Lever or loop handle shall return to neutral positionwhen faucet is turned off.
• Control mechanism shall be the diamond coatedceramic cartridge.
• Red/blue graphics on handle button to indicatehot/cold temperature.
• Touch-Clean® sprayhead.• 3/8" O.D. straight, staggered pex supply tubes –35" (889 mm) and 36" (914 mm) long.
• Standard 3/8” (10 mm) compression gasket fittings.• Integral double check valves in spout.
DSP-K-470-DST Rev. C
2 1/2" (64 mm)Max. DeckThickness
3/8” Compression Fitting
0
1
2
3
4
5
0 10 20 30 40 50 60 70 80 90
Pressure (PSI)
Flo
w (
U.S
. Gal
lon
s P
er M
inu
te) 6
0 69 138 207 276 345 414 483 552 621
0
3.8
7.6
11.4
15.1
18.9
22.7
Pressure (kPa)
Flo
w (L
iters Per M
inu
te)
WE Models
470-DST, 470-WE-DST
®
®
U P C
Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinuemodels, both without notice or obligation. Dimensions are for reference only. See current full-line price book orwww.specselect.com for finish options and product availability.
8" (203 mm)Centers 36"
(914 mm)35"
(889 mm)
9"(229 mm)
10"(254 mm)
6 5/8"(168 mm)
8"(203 mm)
1 15/16"(50 mm)
470-DST/472-DST
470-DST/472-DST
2 1/2" (64 mm)Max. DeckThickness
36"(914 mm)35"
(889 mm)
6 5/8"(168 mm)
2 5/16"(59 mm)Dia.
3/8” Compression Fitting
9"(229 mm)
10"(254 mm)
55 E. 111th Street, Indianapolis, Indiana 46280395 Matheson Blvd. E., Mississauga, ON L4Z 2H2© 2009 Masco Corporation of Indiana
WARRANTY• Lifetime Faucet and Finish Limited Warranty to theoriginal consumer purchaser to be free fromdefects in material and workmanship.
• 5 Year Limited Warranty for usage in all industrial,commercial and business applications.
472-DST
10 3/4" (273 mm)
KS-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
KP
C
ST
PC
CLA
SS
SY
MB
OL
KS-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
KS-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Franke Kindred Canada Limited P.O. Box 190, 1000 Kindred Road, Midland, Ontario, Canada, L4R 4K9 Phone: 800-465-6085 Fax: 800-361-8408
PRINTED
IN CAN
ADA
Franke Kindred Canada Limited
0106
20
7˝ [18cm]
18 9
/16˝
[47
cm]
14˝
[36c
m]
16˝ [41cm]
ø1 1/2˝ [ø4cm] TYP
18 1/8˝ [46cm]
9 1/16˝ [23cm]
8 1/16˝ [20cm]
4˝ [10cm] TYP
L B S 4 6 0 7 –19" x 18" x 7"
SpecificationModel________________________: Single bowl sink with faucet ledge.20 gauge, type 302, 18-8 stainless steel. Self rimming. Exposedsurfaces are satin finished. Underside is fully sound dampened andundercoated. Includes factory applied rim seal, installation kit, and[3-1/2"] or [1-1/2"] waste assembly.
O.D.: 18-9/16" x 18-1/8" x 7" (47cm x 46cm x 18cm)
LBS4607-1: Includes 3-1/2" crumb cup waste assembly, waste location center.
LBS4607-3: Includes 1-1/2" duplex waste assembly, waste location center.
Faucet Hole Drilling❏ 1-hole, 1-1/2" diameter❏ 3-hole, 1-1/2" diameter on 4" centers, 8" widespread❏ Other (non-returnable): _____________________________________
_________________________________________________________
To be specified:
❏ Faucets
❏ Supplies
❏ Trap
❏ Other
Vandal resistant grid:❏ 1300G (for 3-1/2" waste)❏ 100NR (for 1-1/2" waste)
C O M M E R C I A L
LBS4607-1
KS-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Description:P-TRAP SHALL BE 1-1/2” GROUND JOINT, 20 GAUGE TUBULAR BRASS, 20GAUGE 7” WALLBEND, ROUGH BRASS FINISH, BRASS NUTS, LESS FLANGE,LESS CLEANOUT,CERTIFIED BY CSA
Oakville Stamping and Bending Ltd.2200 Speers Road. Oakville, ON. Canada. L6L 2X8.
T. 905.827.0320 or toll free 1.877.314.6040 F. 905.827.6375 or toll free 1.877.827.6040.
All rights reserved. OS&B™ reserves the right to change product specifications and material or discontinue models without notice.
www.osb.ca
114BRBLF1-1/2” 20GA P-TRAP, LESS CLEANOUT
Certification
1012"
267mm
112"
38mm5"
127mm
KS-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
CCOOMMPPLLIIEESS WWIITTHH::• ASME A112.18.1/ CSA B125.1
Indicates compliance toICC/ANSI A117.1
KITCHEN FAUCETS� Signature® Pull-Out Series� Single Handle Deck Mount� Single or 3 Hole Sink Applications
Submitted Model No.: _______________________________________________Specific Features: __________________________________________________
STANDARD SPECIFICATIONS: • Single handle kitchen faucets for exposed mounting onsingle and three hole sinks.
• Centermount or 8" (203 mm) centers with optionalincluded 10 3/4" (273 mm) long escutcheon.
• 8" (203 mm) high, 9" (229 mm) long spout [includes 61/4 (159 mm) long pull-out spray] nestled in all metal hub assembly, swings 120°.
• Spout is connected to valve body with a 53" (1346 mm)long hose that extends to 34" (864 mm) usable length.
• Pull-out spout operates in an aerated or spray modevia an easy side-to-side push lever.
• Lever or loop handle shall return to neutral positionwhen faucet is turned off.
• Control mechanism shall be the diamond coatedceramic cartridge.
• Red/blue graphics on handle button to indicatehot/cold temperature.
• Touch-Clean® sprayhead.• 3/8" O.D. straight, staggered pex supply tubes –35" (889 mm) and 36" (914 mm) long.
• Standard 3/8” (10 mm) compression gasket fittings.• Integral double check valves in spout.
DSP-K-470-DST Rev. C
2 1/2" (64 mm)Max. DeckThickness
3/8” Compression Fitting
0
1
2
3
4
5
0 10 20 30 40 50 60 70 80 90
Pressure (PSI)
Flo
w (
U.S
. Gal
lon
s P
er M
inu
te) 6
0 69 138 207 276 345 414 483 552 621
0
3.8
7.6
11.4
15.1
18.9
22.7
Pressure (kPa)
Flo
w (L
iters Per M
inu
te)
WE Models
470-DST, 470-WE-DST
®
®
U P C
Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinuemodels, both without notice or obligation. Dimensions are for reference only. See current full-line price book orwww.specselect.com for finish options and product availability.
8" (203 mm)Centers 36"
(914 mm)35"
(889 mm)
9"(229 mm)
10"(254 mm)
6 5/8"(168 mm)
8"(203 mm)
1 15/16"(50 mm)
470-DST/472-DST
470-DST/472-DST
2 1/2" (64 mm)Max. DeckThickness
36"(914 mm)35"
(889 mm)
6 5/8"(168 mm)
2 5/16"(59 mm)Dia.
3/8” Compression Fitting
9"(229 mm)
10"(254 mm)
55 E. 111th Street, Indianapolis, Indiana 46280395 Matheson Blvd. E., Mississauga, ON L4Z 2H2© 2009 Masco Corporation of Indiana
WARRANTY• Lifetime Faucet and Finish Limited Warranty to theoriginal consumer purchaser to be free fromdefects in material and workmanship.
• 5 Year Limited Warranty for usage in all industrial,commercial and business applications.
472-DST
10 3/4" (273 mm)
KS-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
KP
C
ST
PC
CLA
SS
SY
MB
OL
KS-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
KS-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
03/03 KINDRED 1-800-465-6085 • FAX 1-800-361-8408 15
13 3
/4˝
[35c
m]
ø1 1/2˝ [ø4cm] TYP 4˝ [10cm] TYP
5 5/8˝ [14cm]
9 1/4˝ [23cm]
6 13/16˝ [17cm]
11 5/8˝ [30cm]
13 5/8˝ [35cm]
6˝ [15cm]
L B S 9 1 0 6 –14" x 14" x 6"
SpecificationModel________________________: Single bowl sink with faucet ledge.20 gauge, type 302, 18-8 stainless steel. Self rimming. Exposed surfacesare satin finished. Underside is fully sound dampened and undercoated.Includes factory applied rim seal, installation kit, and [3-1/2"] or [1-1/2"] waste assembly.
O.D.: 13-3/4" x 13-5/8" x 6" (35cm x 35cm x 15cm)
LBS9106-1: Includes 3-1/2" crumb cup waste assembly.
LBS9106-3: Includes 1-1/2" duplex waste assembly.
Faucet Hole Drilling❏ 1-hole, 1-1/2" diameter❏ 2-hole, 1-1/2" diameter on 4" centers❏ Other (non-returnable): ______________________________________
_________________________________________________________
To be specified:
❏ Faucets
❏ Supplies
❏ Trap
❏ Other
Vandal resistant grid:❏ 1300G (for 3-1/2" waste)❏ 100NR (for 1-1/2" waste)
LBS9106-1 is shown hereLBS9106-3 has same drain location
C O M M E R C I A L
LBS9106-1/3
3 Holes 8" CC
HAND SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Job Name ________________________________________________
Item Number _____________________________________________
Section/Tag ______________________________________________
Model Specified ___________________________________________
Architect _________________________________________________
Engineer _________________________________________________
Contractor ________________________________________________
[ ] Submitted as Shown [ ] Submitted with Variations
Date _____________________________________________________
MECHANICAL FAUCETS
2300-8ABCP
Manual and Metering Faucets
Product Type___________________________________________________Deck Mounted 8" Fixed Centers Single Lever Hot and ColdWater Mixing Sink Faucet
Features & Specifications___________________________________________________• 8" Fixed Centers• 2.2 GPM (8.3 L/min) Aerator• 4-5/8" Lever Handle• Ceramic Volume Control and Hot Water Limit StopCartridge• 3/8" Compression Flexible Stainless Steel Supply Hoses• 10" Center to Center Integral Cast Brass Swing Spout• ECAST® design provides durable brass construction withtotal lead content equal to or less than 0.25% by weightedaverage• CFNow! Item Ships in 5 Days
Performance Specification___________________________________________________• Rated Operating Pressure: 20-125 PSI• Rated Operating Temperature: 40-140ºF
Warranty___________________________________________________• Lifetime Limited Faucet Warranty• 5-Year Limited Cartridge Warranty• 1-Year Limited Finish Warranty
Codes & Standards___________________________________________________• ASME A112.18.1/CSA B125.1• California Health and Safety Code 116875 (AB1953-2006)• Vermont Bill S.152• NSF/ANSI 372 Low Lead Content• ADA ANSI/ICC A117.1
ECAST products are intended for installation where state laws and local
codes mandate lead content levels or in any location where lead content
is a concern.
Last Revision: 11/04/2013 • Date Printed: 06/13/2014 • Product specifications subject to change without notice
2100 South Clearwater DriveDes Plaines, IL
P: 847/803-5000F: 847/803-5454
Technical: 800/TEC-TRUEwww.chicagofaucets.com
HAND SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
2300-8ABCPManual and Metering Faucets
Architect/Engineer Specification________________________________________________________________________________________________________Chicago Faucets No. 2300-8ABCP, Deck Mounted 8" Fixed Centers Single Lever Hot and Cold Water Mixing Sink Faucet, Chrome Plated solid
brass construction. 10" Center to Center Integral Cast Brass Swing Spout. 2.2 GPM (8.3 L/min) Pressure Compensating Softflo Aerator. 4-5/8"
Metal Lever handle(s) with Blue and Red Temperature Indicator. Ceramic quarter turn cartridge, features square tapered stem. 3/8" Compression
Flexible Stainless Steel Supply Hoses. ECAST® construction with less than 0.25% lead content by weighted average. Secondary Control Valve:
10" Center to Center Integral Cast Brass Swing Spout. This product meets ADA ANSI/ICC A117.1 requirements and is tested and certified to
industry standards: ASME A112.18.1/CSA B125.1, California Health and Safety Code 116875 (AB1953-2006), Vermont Bill S.152, and
NSF/ANSI 372 Low Lead Content.
Operation and Maintenance________________________________________________________________________________________________________Installation should be in accordance with local plumbing codes. Flush all pipes thoroughly before installation. After installation,remove spout outlet or flow control and flush faucet thoroughly to clear any debris. Care should be taken when cleaning theproduct. Do not use abrasive cleaners, chemicals or solvents as they can result in surface damage. Use mild soap and warmwater for cleaning and protecting the life of Chicago Faucet products. For specific operation and maintenance refer to theinstallation instructions and repair parts documents that are located at www.chicagofaucets.com.
Chicago Faucets, member of the Geberit Group, is the leading brand of commercial faucets and fittings in the United States,offering a complete range of products for schools, laboratories, hospitals, office buildings, food service, airports and sport facilities.Call 1.800.TECTRUE or 1.847.803.5000 Option 1 for installation or other technical assistance.
Last Revision: 11/04/2013 • Date Printed: 06/13/2014 • Product specifications subject to change without notice
2100 South Clearwater DriveDes Plaines, IL
P: 847/803-5000F: 847/803-5454
Technical: 800/TEC-TRUEwww.chicagofaucets.com
HAND SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
Description:P-TRAP SHALL BE 1-1/2” GROUND JOINT, 20 GAUGE TUBULAR BRASS, 20GAUGE 7” WALLBEND, ROUGH BRASS FINISH, BRASS NUTS, LESS FLANGE,LESS CLEANOUT,CERTIFIED BY CSA
Oakville Stamping and Bending Ltd.2200 Speers Road. Oakville, ON. Canada. L6L 2X8.
T. 905.827.0320 or toll free 1.877.314.6040 F. 905.827.6375 or toll free 1.877.827.6040.
All rights reserved. OS&B™ reserves the right to change product specifications and material or discontinue models without notice.
www.osb.ca
114BRBLF1-1/2” 20GA P-TRAP, LESS CLEANOUT
Certification
1012"
267mm
112"
38mm5"
127mm
HAND SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
KP
C
ST
PC
CLA
SS
SY
MB
OL
HAND SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
HAND SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
M117© 2014 AS America Inc.
AFWALL® MILLENNIUM™ FloWise® ELONGATED FLUSHOMETER TOILET
VITREOUS CHINA with EVERCLEAN®
AFWALL® MILLENIUM™ FloWise® ELONGATED FLUSHOMETER TOILET with EVERCLEAN®
• Wall-mountedflushometervalvetoilet• Vitreouschina• HighEfficiency,LowConsumption.Operatesintherangeof1.1gpfto1.6gpf(4.2Lpfto6.0Lpf)
• MeetsdefinitionofHET(HighEfficiencyToilet)whenusedwithahighefficiencyflushvalve(1.1gpf-1.6gpfor1.28/1.1gpfdualflush)
• MaximumPerformance(MaP)scoreof1,000gramsat1.1gpf-1.6gpf
• PermanentEverClean®antimicrobialsurfaceinhibitsthegrowthofstain-andodor-causingbacteria,mold,andmildewonthesurface
• Condensationchannel• Concealedtrapwaydesign• Elongatedbowl• Powerfuldirect-fedsiphonjetaction• 1-1/2"inletspud• Fully-glazed2-1/8"trapway• 10"x12"watersurfacearea• Staticweightloadof1,000lbs.*• 100%factoryflushtested
❏ 3351.101Elongatedbowlonly,topspud❏ 3352.101Elongatedbowlonly,topspudwith
slottedrimforbedpanholding❏ 3353.101Elongatedbowlonly,backspud❏ 3354.101Elongatedbowlonly,backspudwith
slottedrimforbedpanholding
System MaP* Score: • 1,000gramsofmiso@1.1gpfto1.6gpfwhenusedwithanAmericanStandardflushvalve
* MaximumPerformance(MaP)testingperformedbyIAPMOR&TLab.MaPReportconductedbyVeritecConsulting,Inc.andKoellerandCompany.
Component Parts: ❏ 047007-0070AInletSpud(furnishedwithbowl)
Nominal Dimensions:660x356x381mm(26"x14"x15")
Recommendedworkingpressure–between25psiatvalvewhenflushingand80psistatic
Fixtureonly,lessseat,boltcaps,andflushometervalve
Compliance Certifications -Meets or Exceeds the Following Specifications:• ASMEA112.19.2/CSAB45.1forVitreousChinaFixtures
* Thisproductisnotrecommendedforbariatricuse.
SEEREVERSEFORROUGHING-INDIMENSIONS
Rev.2/14
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES - CHECK LOCAL CODES. When installed so top of seat is 432 to 483mm (17" to 19") from thefinished floor.
BARRIER FREE
To Be Specified:❏ Color:❏White❏ Seat:
❏ AmericanStandard#5901.100Heavydutyopenfrontlesscover
❏ AmericanStandard#5905.100Extraheavydutyopenfrontlesscover
❏ FlushometerValve:❏ 1.6gpf:
❏ Sensor-Operated:AmericanStandardSelectronic®
DCPower#6065.161.002(TopSpud)ACPower#6067.161.002(TopSpud)
❏ Manual:AmericanStandard#6047.161.002(TopSpud)❏ 1.28gpf:
❏ Sensor-Operated:AmericanStandardSelectronic®
DCPower#6065.121.002(TopSpud)ACPower#6067.121.002(TopSpud)
❏ Manual:AmericanStandard#6047.121.002(TopSpud)❏ 1.6/1.1gpfDualFlush:
❏ Sensor-Operated:AmericanStandardSelectronic®
DCPower#6065.761.002(TopSpud)ACPower#6067.761.002(TopSpud)
❏ 1.28/1.1gpfDualFlush:❏ Sensor-Operated:AmericanStandardSelectronic®
DCPower#6065.721.002(TopSpud)ACPower#6067.721.002(TopSpud)
WC-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
M118© 2014 AS America Inc.
NOTES:● Toilet designed to meet ADA accessibility standards when top of seat height set at 432 to 483mm (17" to 19") from finished floor.
PRODUCT3351AND3353SHOWN,3352AND3354SAMEEXCEPTWITHSLOTTEDRIMFORBEDPANHOLDING.WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-FELT (WAX RING NOT RECOMMENDED).SUGGESTED2mm(1/16)CLEARANCEBETWEENFACEOFWALLANDBACKOFBOWL.TOCOMPLYWITHAREACODEGOVERNINGTHEHEIGHTOFVACUUMBREAKERONTHEFLUSHOMETERVALVE,THEPLUMBERMUSTVERIFYDIMENSIONSSHOWNFORSUPPLYROUGHING.FLUSHOMETERVALVENOTINCLUDEDWITHFIXTUREANDMUSTBEORDEREDSEPARATELY.CARRIERFITTINGASREQUIREDTOBEFURNISHEDBYOTHERS.PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORT.
IMPORTANT:DimensionsoffixturesarenominalandmayvarywithintherangeoftolerancesestablishedbyANSIStandardA112.19.2.Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibilityisassumedforuseofsupersededorvoidedpages
FINISHED WALL
FINISHEDFLOOR
(4) Ø 22mm(7/8") HOLES
73m
m(2
-7/8
")
660mm(26")
470mm(18-1/2")
333mm(13-1/8")
356mm(14")
191mm(7-1/2")
133mm(5-1/4")
229mm(9")381mm
(15")
41mm(1-5/8")
FINISHED WALL
FINISHEDFLOOR
660mm(26") (4) Ø 22mm
(7/8") HOLES470mm(18-1/2")
333mm(13-1/8")
356mm(14")
191mm(7-1/2")
90mm(3-9/16")
133mm(5-1/4")
229mm(9")381mm
(15")
41mm(1-5/8")
281mm(11-1/16")
321mm(12-5/8")
3351.101/3352.101
3353.101/3354.101
AFWALL® MILLENNIUM™ FloWise® ELONGATED FLUSHOMETER TOILET
VITREOUS CHINA with EVERCLEAN®
Rev.2/14
BARRIER FREE
WC-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
© 2016 AS America Inc. 9/16
SELECTRONIC® SENSOR-OPERATEDTOILET FLUSH VALVE
HARD-WIRED AC POWER, BASE MODEL
Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for accessible and usable building facilities - check local codes
SUPPLYDN 25mm(1" I.P.S.)
108 mm - 134 mm(4-1/4" - 5-1/4")
FINISHED WALL
FINISHEDFLOOR
73 mm (2-7/8")
409 mm(16-1/8")
TYPICAL WATER CLOSET INSTALLATION:AFWALL® TOILET SHOWN
293 mm(11-1/2")
-C-L-
COVER &ELECTRICAL
BOX
160 mm(6-1/4")
86 mm(3-3/8")
BASE MODEL: (Does Not Include Power Supply)
❑ 606B.161 Base Model, 1.6 gpfFor use with Hard-Wired AC or Multi-ACpower kits. 11-1/2" rough-in
❑ 606B.121 Base Model, 1.28 gpfSAME AS ABOVE
❑ 606B.111 Base Model, 1.1 gpfSAME AS ABOVE
❑ 606B.761 Base Model, Dual Flush 1.6 / 1.1 gpfSAME AS ABOVE
❑ 606B.721 Base Model, Dual Flush 1.28 / 1.1 gpfSAME AS ABOVE
POWER KITS: (Must be Purchased Separately)
❑ PK00.HAC Hard-Wired AC transformer, 10’ extensioncable and capacitor module
❑ PK00.MAC Multi-AC adapter and 10” extension cable
OPERATING PRESSURE:25 psi (flowing) - 80 psi (static)
FLOW REQUIREMENT:25 gpm (94.6 L/min.)
GENERAL DESCRIPTION:Exposed, Sensor Operated Selectronic® Water Closet Flush Valve for floor-mounted or wall-hung 1-1/2" top spud bowls.Inlet includes 1" I.P.S. angle stop with back-flow protection, vandal-resistant cap, sweat solder kit, cover tube and wall flange.Outlet includes 1-1/2" vacuum breaker, spud couplingand flange.
PRODUCT FEATURES:• Electronic flush valve with Selectronic® proximity system
for “Hands Free” operation• Self-Cleaning Piston operation with integral wiper spring
prevents clogging and reduces maintenance• Piston operation delivers superior flush accuracy and
repeatability• Adjustable tailpiece• Chemical resistant EPDM seals are unaffected by chloramines and ammonia
• Valve remains closed and does not need to be reset after loss of power or water pressure
• Stadium Feature: Valve automatically switches to waterconservation mode during periods of heavy usage
• Fully Mechanical Manual Override Button can flush toilet during a power outage
• Vandal-resistant metal cover plate (for 2-gang electric box supplied by others) with no visible fasteners
• Sensor & electronic controls are fully enclosed and waterresistant
• Range can be adjusted manually or by remote control• Sanitary Flush - Valve automatically flushes after 24 hours
of non-use to clean fixture & maintain trap seal• No external volume adjustment• 5 second Arming Delay prevents unintentional flushing• 3-second Flush Delay• Can be installed left or right-handed
RECOMMENDED SPECIFICATION:Electronic proximity infrared sensor activated toilet flush valve shall feature self-cleaning piston valve. Includes a UL listed hard-wired power supply that provides 6 VDC power to run system. Includes a fully mechanical manual over-ride that can provide a complete flush without power.Includes cast brass valve body and metal cover with chrome finish and vandal resistant stop cap. Angle stop with back-flow protection and vacuum breaker included. Flush valve shall be American Standard Model # 606B.___.002
WC-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
© 2016 AS America Inc. 9/16
SELECTRONIC® SENSOR-OPERATEDTOILET FLUSH VALVE
HARD-WIRED AC POWER, BASE MODEL
Roughing-in Dimensions
Right or Left Hand Installation
*Note: The Critical Line (-C-L-) on Vacuum Breakermust typically be 6" min. (152 mm) above fixture.Consult Codes for details.
TOP OFFIXTURE
409 mm(16-1/8")
293 mm(11-1/2")
-C-L-
116 mm(4-5/8")
86 mm(3-3/8")
72 mm(2-7/8")
DETECTION ZONE400 mm-800 mm
(15-3/4" TO 31-1/2")
2-GANG ELECTRICALBOX BY OTHERS
SUPPLYDN 25mm(1" I.P.S.)
15˚
FINISHED WALL
51 mm (2") HOLEFOR CONDUIT
108 mm-134 mm(4-1/4" TO 5-1/4")
FOR 1-1/2" TOPSPUD FIXTURES
MANUALOVERRIDE
BUTTON
*CRITICALLEVEL
45˚
180 ˚
305 mm(12" MAX.)
160 mm(6-1/4")
160 mm(6-1/4")
57 mm (2-1/4") -137 mm (5-3/8")
LISTINGS:• ASSE 1037• ANSI/ASME A112.19.2• ADA Compliant
Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for accessible and usable building facilities - check local codes
WC-1
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
ES-WD-ISCA-101-LR CANADA 0535 (Dimension) Denotes Millimeters
Job Name
Job Location
Engineer
Contractor
Contractor's P.O. No.
Representative
B3
Tag:
WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to productspreviously or subsequently sold. See your WATTS Drainage representative for any clarification. Dimensions are subject to manfacturing tolerances.
© Watts Drainage 2004
CANADA
CANADA: 5435 North Service Road, Burlington, ON, L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www.wattsdrainage.ca
CANADA
ISCA-101-L/R Industry StandardSingle Horizontal
Adjustable Closet Carrier
SPECIFICATION: Watts Drainage Products ISCA-101-L/R Industry Standard single horizontal adjustable water closet carrier with epoxy coated cast iron fitting, 4"(102) no hub waste and 2"(51) no hub vent connections, epoxy coated cast iron patent pending compression seal faceplate assembly, epoxy coated cast iron foot supports adjustable for standard and wheelchair height, adjustable ABS nipple with integral test cap and neoprene bowl gasket, plated hardware and chrome cap nuts.
Notes:Siphon jet (4 bolt) arrangement shown. Invert faceplate assembly for blow-out (3 bolt) bowls.
Anchor legs to concrete floor with minimum 1/2" lag bolts (by others).
Options (Select One or More)Suffix Description
-M1 ABS Extended Nipple (Up to 24")
-M11 Tiling Frame
-M20 Flush Valve Support
-36 36" Long Barrel Fitting
CA-100-EXT Aux. Support System w/Extended Nipple
X = 5-3/4" Maximum with Standard Nipple
2-3/4" 6"
10-1/2"
1"
2-3/16"
3"
"X"
5/16"
NO HUB FITTING
0" MIN.4" MAX.
9"
15"
7-1/2"
4-7/8" MIN.9-1/2" MAX.
17-3/4"
FACEPLATEASSEMBLYW/COMPRESSIONSEAL
REMOVABLE LUGSFOR SHALLOW ROUGH-IN
DUAL SLOTTEDLEGS
REAR ANCHOR SUPPORT
ASTM C564COMPRESSIONGASKET
ABS NIPPLEW/INTEGRALTEST CAP
Note:Left hand carrier shown; right hand carrier is mirror image.
11-1/2 MIN."17-1/4" MAX.
5-5/16"
-M3 Galvanized Steel Nipple 7"
WC-1 CARRIER
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
M67© 2010 AS America Inc.
MADERA™ FloWise® 16-1/2" HEIGHT 1.28 GPF FLUSHOMETER TOILET
VITREOUS CHINA with EVERCLEAN®
MADERA™ FloWise® 16-1/2" HEIGHT with EVERCLEAN®
• Floor mount flushometer valve toilet• Vitreous china• Meets definition for HET (High Efficiency Toilet)• High Efficiency (4.8 Lpf/1.28 gpf)• Will also function at 1.1gpf and 1.6gpf with a
properly set dual flush valve• EverClean® surface inhibits the growth of
stain- and odor-causing bacteria, mold,and mildew on the surface
• 10" or 12" roughing-in• 16-1/2" rim height for accessible application• Condensation channel• Elongated bowl• Powerful direct-fed siphon jet action• Fully glazed 2-1/8" trapway• 10" x 12" water surface area• 1-1/2" top spud• 2 bolt caps• 100% factory flush tested
❏ 3461.128 Elongated bowl only, top spud❏ 3461.001 Same as above, Universal Bowl❏ 3462.128 Elongated bowl only, top spud with
slotted rim for bedpan holding (White only)❏ 3462.001 Same as above, Universal Bowl❏ 3465.128 Elongated bowl only, top spud
with 4 bolts❏ 3465.001 Same as above, Universal Bowl❏ 3466.128 Elongated bowl only, top spud with
slotted rim for bedpan holding with 4 bolts(White only)
❏ 3466.001 Same as above, Universal Bowl❏ 3463.128 Elongated bowl only, back spud❏ 3463.001 Same as above, Universal Bowl❏ 3464.128 Elongated bowl only, back spud with
slotted rim for bedpan holding (White only)❏ 3464.001 Same as above, Universal Bowl
Component Parts:❏ 047007-0070A Inlet spud (furnished with bowl)❏ 481310-100 Bolt caps with retainers
(furnished with bowl)
Nominal Dimensions:718 x 356 x 419mm (28-1/4" x 14" x 16-1/2")
Recommended working pressure–between25 psi at valve when flushing and 80 psi static
Fixture only, less seat and flushometer valve
Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.2-2008 / CSA B45.1-08 for Vitreous
China Fixtures
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES - CHECK LOCAL CODES. When installed so top of seat is 432 to 483mm (17" to 19") from thefinished floor.
To Be Specified:❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black❏ Seat:
❏ American Standard #5901.100 Heavy duty openfront less cover
❏ American Standard #5905.100 Extra heavy dutyopen front less cover
❏ Flushometer Valve:❏ American Standard Selectronic™ #6065.121.002
DC Power (Top Spud)❏ American Standard Selectronic™ #6065.221.007
DC Power (Back Spud)❏ American Standard Selectronic™ #6067.221.007
AC Power (Back Spud)❏ American Standard Selectronic™ #6068.221.007
Multi AC Power (Back Spud)
Revised 4/10
BARRIER FREE
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
WC-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
M68© 2010 AS America Inc.
NOTES:PRODUCT 3461 AND 3463 SHOWN, 3462 AND 3466 SAME AS EXCEPT WITH SLOTTED RIM FOR BED PAN HOLDING.TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON THE FLUSHOMETER VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR SUPPLY ROUGHING.THIS TOILET DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 254MM (10") AND A MAXIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.FLUSHOMETER VALVE NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. FLUSHOMETER VALVE REQUIREMENTS FOR 12" (305MM) ROUGH-IN: SWEAT EXTENSION NIPPLE IS REQUIRED. REFER TO VALVE MANUFACTURER AND LOCAL CODES.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
238mm(9-3/8")
419mm(16-1/2")
438mm(17-1/4")
470mm(18-1/2")
356mm(14")
338mm(13-5/16")
150mm(5-7/8")
254mm(10")
13mm(1/2")
76mm(3")
718mm(28-1/4")
C/L OF SEAT POST HOLES140mm (5-1/2") CENTERS
FINISHED WALL
FINISHED FLOOR
C/L OF OUTLET
MADERA™ FloWise® 16-1/2" HEIGHT 1.28 GPF FLUSHOMETER TOILET
VITREOUS CHINA with EVERCLEAN®
711mm(28")
1-1/2"SPUD
121mm(4-3/4")
238mm(9-3/8")
419mm(16-1/2")
470mm(18-1/2")
356mm(14")
338mm(13-5/16")
150mm(5-7/8")
254mm(10")
13mm(1/2")
25mm(1")
102mm(4")
718mm(28-1/4")
C/L OF SEAT POST HOLES140mm (5-1/2") CENTERS
FINISHED WALL
FINISHEDFLOOR
C/L OF OUTLET
1" N.P.T. OR 1" C.W.T. SUPPLYTO FLUSH VALVE
3461.128/3462.128/3465.128/3466.1283461.001/3462.001/3465.001/3466.001
3463.128/3464.1283463.001/3464.001
BARRIER FREE
Revised 4/10
WC-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
MODEL NUMBER:
❑ 6065.121.002 FlushValvefor11-1/2"SupplyC\Ltotopofbowl,1.28gpf
❑ 6065.122.002FlushValvefor27"SupplyC\Ltotopofbowl,1.28gpf
❑ 6065.525.002 RetrofitforExistingFlushValves,1.28gpf.Replacesindustrystandardmanualandelectronicvalves.Doesnotincludethevacuumbreakerassembly,anglestoporsweatsolderkit.
OPERATING PRESSURE:OverallRange:20-125psi**Recommended:25psi(flowing)-80psi(static)
FLOW REQUIREMENT:25gpm(94.6L/min.)
**Waterpressureover80psiisnotrecommendedformostplumbingfixtures.
BATTERY LIFE:Upto4-yearlife,(approx.200,000cycles)
ACCESSORIES:• Castwallflanges(3/4",1"&1-1/2")• Solidringpipesupports(2-1/2"&6"C-E)• Splitringpipesupports(2-1/2"&6"C-E)
RECOMMENDED SPECIFICATION:Electronicproximityinfraredsensoractivatedtoiletflushvalveshallfeatureself-cleaningpistonvalve.Includesafullymechanicalmanualover-ridethatcanprovideacompleteflushwithoutbatterypower.Includescastbrassvalvebodyandmetalcoverwithchromefinish,vandalresistantstopcapandlithiumbattery.Anglestopwithback-flowprotectionandvacuumbreakerincluded.1.28gpf/4.8LpfFlushvalveshallbeAmericanStandardModel#6065.12_.002.
GENERAL DESCRIPTION:Exposed,BatteryPowered,SensorOperatedSelectronic™WaterClosetFlushValveforfloor-mountedorwall-hung1-1/2"topspudbowls.
Inletincludes1"I.P.S.anglestopwithback-flowprotection,vandal-resistantcap,sweatsolderkit,covertubeandwallflange.
Outletincludes1-1/2"vacuumbreakerwithadjustabletailpiece,spudcouplingandflange.
PRODUCT FEATURES:• ElectronicflushvalvewithSelectronic™proximitysystemfor“HandsFree”operation• Self-CleaningPistonoperationhelpspreventcloggingandreducesmaintenance
• Positivesealensuresleak-freeperformance• FullymechanicalManualOverrideButtoncanflushtoiletduringapoweroutage
• Rangecanbeadjustedmanuallyorbyremotecontrol
• Sensor&electroniccontrolsarefullyenclosedandwaterresistant
• Automaticallyflushesafter24hoursofnon-usetomaintaintrapseal• Safetytimerhelpspreventvandalismbyturningoffthevalveifsensoriscoveredformorethan1minute
• 3-secondFlushDelay• LowBatteryindicator• Batterycanbechangedwithoutturningoffthewater• Factory-installed6Vlithiumbatteryincluded• Canbeinstalledleftorright-handed• ADAcompliant
SELECTRONIC™ FloWise®
TOILET FLUSH VALVEBATTERY POWERED, SENSOR OPERATED, 1.28 GPF
©2008ASAmericaInc.L115
Revised10/09
WC-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
SELECTRONIC™ FloWise®
TOILET FLUSH VALVEBATTERY POWERED, SENSOR OPERATED, 1.28 GPF
LISTINGS:• ASSE1037• ANSI/ASMEA112.19.2• ADACompliant
©2008ASAmericaInc.L116
WC-2
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
DETAILS500CCHeavy Duty open front less cover for elongatedbowl. Plated steel check hinge with PVC wash-ers and plastic nuts.
500CCSSHeavy Duty open front less cover for elongatedbowl. Plated steel self sustaining check hingewith PVC washers and plastic nuts.
500STSCCHeavy Duty open front less cover for elongatedbowl. Stainless steel check hinge with PVCwashers, metal flat washers, lock washers andstainless steel nuts.
500STSCCSSHeavy Duty open front less cover for elongatedbowl. Self sustaining stainless steel checkhinge with PVC washers, metal flat washers,lock washers, stainless steel nuts and self sustaining check hinge.
Standard Features:• Corrosion free steel hinge posts• Check hinge posts• Extended back with concealed hinge• Integrally molded permanent and sanitary
color keyed bumpers• Corrosion free hardware• Withstands cleansers, strong chemicals• Easy clean
I n s t i t u t i o n a l C o m m e r c i a l
Solid Plastic Seats
DETAILS
SPECIFICATIONS
500 SERIES
Seats shall be Centoco No.________________Seat and cover shall be injection molded ofhigh strength, impact resistant thermoplasticwith integrally molded permanent bumpersand steel reinforced check hinges standard.
Color to be ___________________.
WC-2
500STSCC
White
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
1© 2012 Fiat Products
FIATPRODUCTS
®
Customer Service Canada1-800-387-0369www.fiat.ca
Customer Service United States1-800-442-1902
www.fiatproducts.com
MOLDED-STONE® UTILITY SINK
MOLDED STONE® UTILITY SINKDL-17-20 & DL17-206
DL-17-20• Molded Stone self-rimming, single bowl utility sink• Standard 3-1/2" (89mm) drain opening• 9-1/2" deep (24mm)
DL-17-206Same as model DL-17-20 in a six pack quantity
9/12
15"(381mm)
20"(508mm)
1-3/4"(44mm)
7-1/2"(191mm)
10"(254mm)
1-1/4"(32mm)
1-3/4"(44mm)
8"(203mm)
2"(51mm)
2"(51mm)
4"(102mm)
17"(432mm)
14"(356mm)
3-1/2"(89mm)
11"(279mm)
9-1/4"(235mm)
SERVICE SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
TWO HANDLE LAUNDRY FAUCETS
COMPLIES WITH:
Suggested Specifications
Two handle deck faucet with 10.2 cm (4”) centre and 15.24 cm (6”) swing spout.
Valve mechanisms shall be of the rotating compression type.
Hot and cold stem units are interchangeable.
All operating parts above the deck are replaceable.
All exposed metal surfaces shall be chrome-plated.
Valves shall be used with replaceable chrome-plated brass seats.
Chrome handles.
Aerator
Flow restricting, 8.3 litres per minute maximum (2.2 gpm), chrome plated brass housing.
DELTA FAUCET CANADA(a division of Masco Canada Limited)420 Burbrook PlaceLondon, Ontario N6A 4L6www.deltafaucet.com
WSP-K-29W211
ASME A112.18.1 / CSA B125.1
29W211 / 29W221
Acme threads engaged at all times for long lifeLubrication lasts and water is sealed out
Buna N Nitrile Radial Seal “O” ring
Buna N Nitrile seat washer
Stainless steel screw
Nickel chrome-plated renewable brass seats
1
2
3
4
5
Brass Stem - Compression
Compression
Direct Copper Inlets
Flexible Supply Inlets
Spout End Hose Adapter
Trap Seal Primer
29W211 29W221
X XX
X
Model ModelFeatures
27W411
Model27W411
XX
XX
X X
2.0”(5.0 cm)
5.0”(11.6 cm)
1.9”(4.9 cm)
6.0”(14.0 cm)
1-1/4” (3.1 cm)max. deck thickness
4.0”(10.2 cm) 6.2”(15.8 cm)
X
SERVICE SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
SB850 24"x24"x12"MOP SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
FIATR
255 Hutchings St. • Winnipeg, MB • R2X 2R4 • Ph. 800-665-7531 • 204-633-6122 • Fx. 204-632-4854e-mail: [email protected] • website: www.fiat.ca
A subsidiary of CR/PL, L.L.C. Company – Evanston, IL
Service-Sink FaucetModel: 830-AA
General:
Material:Finish:
Specificationsand Codes:
830-AA Service Faucet - Chrome plated withvacuum breaker, integral stops, adjustable wallbrace, pail hook and 3/4” hose thread on spout.Body inlets 8” center to center, four armhandles. Valves contain renewable hub,renewable seats, swivel discs, encased washersand brass washer screws.
Commercial red brass alloy casting-rough finish.
Chrome plating exceeding requirements ofANSI/ASTM B-456-71. Indicators cold (blue) andhot (red) are included.
In the U.S.A., meets or exceeds requirements ofANSI-A112.18.1M-1979 for “Finished andRough Brass Plumbing Fixture Fittings.” InCanada, meets or exceeds the requirements ofCSA standards B125 - “Plumbing Fittings,”B64.1.1 - “Vacuum Breakers - AtmosphereType” and B64.0 - “General Requirements forBackflow Preventers and Vacuum Breakers,”and is approved under Product Class No. 681101 under Report #LM57412-1. Conforms toASSE 1001.
NOTE: These roughing measurements mayvary 1/4” (plus or minus).
3/4” (19) HOSE THREAD
VACUUM BREAKER
9-3/8” (238)2-7/8” (73)
3/4” (19)
1/2” (13) I.P.S.MALE THREADS
1/8” (3) ECCENTRIC
9” (229)APPROX.
BUCKETHOOK
1-1/2”(38)
SIDE VIEW
FRONT VIEWINTEGRAL STOPS
2-3/8” (60) DIA.
HOT COLD
8” (203)
33888_830-AA Faucet Spec. Sheet 2/27/2003 4:32 PM Page 1
MOP SINK
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
ES-WD-FD-100-C-A CANADA 0403 (Dimension) Denotes Millimeters
FD-100-C-A
SPECIFICATION: Watts Drainage Products FD-100-C-A epoxy coated cast iron floor drain with anchor flange, reversible membrane clamp with primary and secondary weepholes,1/4"(6) thick (specify diameter) adjustable nickel bronze (standard) strainer, and no hub (MJ) (standard) outlet.
Floor Drain withRound Strainer
Job Name
Job Location
Engineer
Contractor
Contractor's P.O. No.
Representative
Components:FC-1B3
* The load classifications are in accordance with the American National Standards ASME A112.21.1MASME Ratings are as follows:MD - Safe Live Load 2000-4999 lbs.(900-2250kg)The above categories are given as a guide only. Please consult factory.
BLT3-XYC
Tag:
A
8-1/8"(206)5-1/8"(130) 6"(152)
7"(178) 8"(203)
PIPE SIZE2"(51), 3"(76), 4"(102)
6"(152) NH (MJ) only
FULL 4" (102) THROATPRIMARY WEEPHOLES
REVERSIBLE MEMBRANE CLAMP
SECONDARY WEEPHOLESSEEPAGE COLLECTION SUMP
SERRATED FLANGE
B3 BODY
(P) PUSH-ON GASKET(ASTM C-564)
1/2"(13) NPT
PIPE STOP
"A" 1/4" (6)NICKEL BRONZE STRAINER
2-1/4"(57)
See Chart A
See Chart B
5"(127) Diameter, Nickel BronzeA5-1 A6-1 6"(152) Diameter, Nickel Bronze
7"(178) Diameter, Nickel BronzeA7-1 A8-1 8"(203) Diameter, Nickel Bronze
WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to productspreviously or subsequently sold. See your WATTS Drainage representative for any clarification. Dimensions are subject to manufacturing tolerances.
© Watts Drainage 2003
CANADA
CANADA: 5435 North Service Road, Burlington, ON, L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www.wattsdrainage.ca
Std. P T X 60/61No Push Female Inside PVC/Pipe
Size Hub On Thread Caulk ABS
2"(51) 3-5/8"(92) 4-1/2"(114)4-1/4"(108)4-1/4"(108) 3-3/4"(95)3"(76) 3-5/8"(92) 4-1/2"(114)4-1/4"(108)4-1/4"(108) 3-3/4"(95)4"(102) 3-5/8"(92) 4-1/2"(114)4-1/4"(108)4-1/4"(108) 4"(102)6"(152) 3-1/2"(89)
Chart B
Str. Dia. Min. Max.
Chart ALoad Free Area
Rating Sq. In.
5"(127)6"(152) 2-3/4"(70)
13/16"(21)7/8"(22)
2-1/2"(64) *MD 8*MD 9
7"(178)8"(203) 2-7/8"(73)
11/16"(17)7/8"(22)
2-1/2"(64) *MD 12*MD 18
-5 Sediment Bucket-6 Vandal Proof
-8
-13 All Galvanized-15 Strainer Extension (DD-50)
-F4-50 4" Round Cast Iron Funnel
-F4-1 4" Round Nickel Bronze Funnel-F6-1 6" Round Nickel Bronze Funnel
-G-50 4x9" Oval Cast Iron Funnel
-G-1 4x9" Oval Nickel Bronze Funnel
Options (Select One or More)Suffix Description
No Hub (MJ)Push On PThreaded Outlet TInside CaulkX
Backwater Valve (3" / 4" Only)
Outlet Type (Select One) Suffix Description
2"(51) Pipe Size23"(76) Pipe Size 34"(102) Pipe Size 46"(152) Pipe Size6
Pipe Sizing (Select One)Suffix Description
PVC Body w/Socket Outlet-60ABS Body w/Socket Outlet-61
Optional Body Material (NH Only)Suffix Description
NH
Ex. FD-102P-C-A5-1
Strainer (Select One)Suffix Description
Order Code: FD-10 - - -C-
-113M Special Epoxy from 3M Range
-SO Side Outlet-Z Elastomeric Flange
TRAP PRIMER CONNECTION
PUSH-ON SHOWN
-12 Galvanized Top
2
CANADA
FLOOR DRAIN
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
WASHBROOK™ FloWise®
UNIVERSAL URINALVITREOUS CHINA
WASHBROOK™ FloWise® UNIVERSAL URINAL
� 6590 001 Universal Top Spud
� 6515 001
6515 001
6590 001
Universal Back Spud
Nominal Dimensions: 480 x 360 x 664mm(18-7/8" x 14-1/8" x 26-1/8")
Recommended working pressure-- between 20 psi at valve when flushing and 80 psi static.
© 2011 American Standard COM-210
�When installed so top of rim is 387mm (15-1/4") from finished floor.MEETS THE AMERICAN DISABILITIES ACT GUIDELINES ANDANSI A117.1 ACCESSIBLE AND USEABLE BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
• Vitreous china• Ultra High Efficiency, Low Consumption operates
in the range of 0.10 to 0.8gpf (0.5 to 3.8Lpf)• Flushing rim• Elongated 14-1/8" (360mm) rim from finished wall• Washout flush action• Extended sides for privacy• 3/4" inlet spud• Outlet connection threaded 2" inside (NPTF)• 2 Wall hangers• Fixture only, (Flush valve shown not included)• Meets ANSI flush requirements at 0.10 to 0.8gpf
(0.5 to 3.8Lpf)
BARRIER FREE
13mm(1/2)
102mm(4)
GASKET
2" N.P.T.INSIDE THREADSFINISHED WALL
13mm(1/2)
DETAIL OF OUTLET CONNECTION
To Be Specified� � �
Meets or Exceeds the Following Specifications:Compliance Certifications -• ASME A112.19.2-2008/CSA B45.1-08 for VitreousChina Fixtures
White Bone Colour:
NOTES:FLUSH VALVE NOT INCLUDED AND MUST BE ORDERED SEPARATELY.PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerancesestablished by ANSI Standard A112.19.2.These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
02/11
3/4"SPUD
464mm(18-1/4")
51mm(2")
238mm(9-3/8")
360mm(14-1/8")
2" N.P.T. FEMALE OUTLET CONNECTION
13mm(1/2")
387mm(15-1/4") MAX
610mm (24")
OPTIONAL
121mm(4-3/4")
3/4"SPUD
3/4" S.P.S. OR 3/4" C.W.T.SUPPLY TO FLUSH VALVE
438mm(17-1/4")
664mm(26-1/8")
REF.
464mm(18-1/4")
292mm(11-1/2")
83mm(3-1/4")
102mm(4")
480mm(18-7/8")
343mm(13-1/2")
C/L OFOUTLET
K2 HANGERS
8mm X 25mm(5/16" X 1")SLOT
64mm(2-1/2")
238mm(9-3/8")
360mm(14-1/8")
2" N.P.T. FEMALE OUTLET CONNECTION
13mm(1/2")
FINISHED FLOOR
FINISHEDWALL
387mm(15-1/4") MAX
610mm (24")
OPTIONAL
� Flush Valve:
0.8 gpf/3.8Lpf Flush Valve: Sensor-Operated: � Selectronic® 6063101.002 DC Power (Top Spud) � Selectronic® 6062310.007 AC Power (Back Spud)0.8 gpf/3.8Lpf Flush Valve: Manual-Operated: � 6045101.0020.4 gpf/1.9Lpf Flush Valve: Sensor-Operated: � Selectronic® 6063051.002 DC Power (Top Spud) � Selectronic® 6062305.007 AC Power (Back Spud)0.4 gpf/1.9Lpf Flush Valve: Manual-Operated: � 6045051.0020.10 gpf/0.5Lpf Flush Valve: Sensor-Operated: � Selectronic® 6063013.002 DC Power (Top Spud) � Selectronic® 6062301.007 AC Power (Back Spud)0.10 gpf/0.5Lpf Flush Valve: Manual-Operated: � 6045013.002
� Stainless Steel Strainer: 047068-0070A
URINAL
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
© 2016 AS America Inc. 9/16
BASE MODEL: (Does Not include Power Supply)
❑ 606B.101 Base Model, 1.0 gpfFor use with Hard-Wired AC or Multi-ACpower kits. 11-1/2" rough-in
❑ 606B.051 Base Model, 0.5 gpfSAME AS ABOVE
❑ 606B.025 Base Model, 0.25 gpfSAME AS ABOVE
❑ 606B.013 Base Model, 0.125 gpgSAME AS ABOVE
POWER KITS: (Must be Purchased Separately)
❑ PK00.HAC Hard-Wired AC transformer, 10’ extensioncable and capacitor module
❑ PK00.MAC Multi-AC adapter and 10” extension cable
OPERATING PRESSURE:20 psi (flowing) - 80 psi (static)
FLOW REQUIREMENT:10 gpm (37.9 L/min.)
RECOMMENDED SPECIFICATION:Electronic proximity infrared sensor activated toilet flush valve shall feature self-cleaning piston valve. Includes a fully mechanical manual over-ride that can provide a complete flush without power. Includes cast brass valve body and metal cover with chrome finish and vandal resistant stop cap. Angle stop with back-flow protection and vacuum breaker included. Flush valve shall be American Standard Model # 606B.___.002
57 mm (2-1/4") -76 mm (3") 115 -134 mm
(4-1/2" TO 5-1/4")
FOR 3/4" TOPSPUD FIXTURES
SUPPLYDN 20 mm(3/4" I.P.S)
292 mm(11-1/2")
FINISHED FLOOR
FINISHEDWALL
-C-L-
CRITICALLEVEL
152 mm(6") MIN.
160 mm(6-1/4")
COVER &ELECTRICAL
BOX
86 mm(3-3/8")
SELECTRONIC® SENSOR OPERATEDURINAL FLUSH VALVE
HARD-WIRED AC POWER, BASE MODEL
GENERAL DESCRIPTION:Exposed, Sensor Operated Selectronic® Urinal Flush Valve for 3/4" top spud urinals.Inlet includes 3/4" I.P.S. angle stop with back-flow protection, vandal-resistant cap, sweat solder kit, cover tube and wall flange.Outlet includes 3/4" vacuum breaker, spud couplingand flange.
PRODUCT FEATURES:• Exclusive Pressure Compensation feature eliminates the
need for the installer to adjust the stop valves, saving timeand money and ensuring water savings
• Electronic flush valve with Selectronic® proximity systemfor “Hands Free” operation
• Self-Cleaning Piston operation with integral wiper springprevents clogging and reduces maintenance
• Piston operation delivers superior flush accuracy andrepeatability
• Adjustable tailpiece• Chemical resistant EPDM seals are unaffected by chloramines and ammonia
• Valve remains closed and does not need to be reset afterloss of power or water pressure
• Stadium Feature: Valve automatically switches to waterconservation mode during periods of heavy usage
• Fully Mechanical Manual Override Button can flush toiletduring a power outage
• Vandal-resistant metal cover plate (for 2-gang electricbox supplied by others) with no visible fasteners
• Sensor & electronic controls are fully enclosed and waterresistant
• Range can be adjusted manually or by remote control• Sanitary Flush - Valve automatically flushes after 24 hours
of non-use to clean fixture & maintain trap seal• No external volume adjustment• 5 second Arming Delay prevents unintentional flushing• 3-second Flush Delay• Can be installed left or right-handed
Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for accessible and usable building facilities - check local codes
URINAL
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
9/16
TOP OFFIXTURE
LISTINGS:• ASSE 1037• ANSI/ASME A112.19.2• ADA Compliant
Roughing-in Dimensions
Right or Left Hand Installation
*Note: The Critical Line (-C-L-) on Vacuum Breakermust typically be 6" min. (152 mm) above fixture.Consult Codes for details.
409 mm(16-1/8")
152 mm(6") MIN.
293 mm(11-1/2")
-C-L-
-C-L-
116 mm(4-5/8")
86mm(3-3/8)
72 mm(2-7/8")
DETECTION ZONE400 -800 mm
(15-3/4 TO 31-1/2)
SUPPLYDN 20 mm(3/4"" I.P.S.)
15˚
FINISHED WALL
51 mm (2") HOLEFOR CONDUIT
115 -134 mm(4-1/2" TO 5-1/4")
FOR 3/4" TOPSPUD FIXTURES
MANUALOVERRIDE
BUTTON
*CRITICALLEVEL
45˚
180 ˚
305 mm(12") MAX.
160 mm(6-1/4")
160 mm(6-1/4")
57 mm (2-1/4") -76 mm (3")
2-GANG ELECTRICALBOX BY OTHERS
SELECTRONIC® SENSOR OPERATEDURINAL FLUSH VALVE
HARD-WIRED AC POWER, BASE MODEL
© 2016 AS America Inc.
Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for accessible and usable building facilities - check local codes
URINAL
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
ES-WD-CA-311,321 CANADA 0403 (Dimension) Denotes Millimeters
CA-311, 321
CA-311
Urinal Carriers
Job Name
Job Location
Engineer
Contractor
Contractor's P.O. No.
Representative
Tag:
SPECIFICATION: Watts Drainage Products CA-311 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet, universal steel hanger support plate, and plated hardware.
CA-321 SPECIFICATION: Watts Drainage Products CA-321 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet, universal steel hanger support plate and bottom bearing plate, and plated hardware.
42"(1067)
20-1/2"(521)
4-1/2"(114)
3-1/4"(83)
FIXTURE HANGERSUPPORT PLATECA-311 ASSEMBLYWHEN USED WITHOUTLOWER PLATE.CA-321 ASSEMBLYWHEN USED WITH LOWER PLATE
TO SUITFIXTURE
ROUGH-IN
LOWERBEARING PLATE
BACK OFSUPPORTBRACKET
FRONT OFSUPPORTINGPLATE
RECTANGULARSTEEL STRUCTURALUPRIGHTS
HEAVY DUTYSTEEL FOOT SUPPORTS
FIXTUREHANGERSUPPORTINGSTUDS
BEARING STUDSNOT ATTACHEDTO FIXTURE
1" x 2"(25 x 51)
NOTE: FOOT SUPPORTS SHOULD BESECURELY ANCHORED TO FLOORWITH 1/2" BOLTS AND ANCHORSBY OTHERS.
NOTE: Recommended for support of wall-hung urinals independent of wall.
WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to productspreviously or subsequently sold. See your WATTS Drainage representative for any clarification. Dimensions are subject to manufacturing tolerances.
© Watts Drainage 2003
CANADA
CANADA: 5435 North Service Road, Burlington, ON, L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www.wattsdrainage.ca
Order Code:CA-321-
Ex. CA-311-M51
Options (Select One or More)Suffix Description
Wall Thickness over 5", per add inch (single)
-M51
Wall Thickness over 12", per inch(Back to Back)
-M52
Vandal Proof Trim, Single-M53Floor to Ceiling Adaptor, Single-M59Valve Supporting Plate, Single-M60Valve Supporting Bar, Single-M61Flush Valve Piping Support, Single-M62
CA-311-OR
272
CANADA
URINAL
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales
ES-WD-WUCO CANADA 0403 (Dimension) Denotes Millimeters
WUCO
SPECIFICATION: Watts Drainage Products WUCO wall cleanout with two-piece expandable cleanout plug, stainless steel access cover, and vandal proof stainless steel screw.
Expandable Line Cleanoutwith Wall Access Cover
Job Name
Job Location
Engineer
Contractor
Contractor's P.O. No.
Representative
Tag:
1-1/8"(29)(STANDARD)
"B"
EXPANDABLE PLUG
STAINLESS STEEL COVER
1-1/2"(38) Plug Size11/22"(51) Plug Size 23"(76) Plug Size 34"(102) Plug Size4
Plug Sizing (Select One)Suffix Description
WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to productspreviously or subsequently sold. See your WATTS Drainage representative for any clarification. Dimensions are subject to manufacturing tolerances.
© Watts Drainage 2003
CANADACANADA: 5435 North Service Road, Burlington, ON, L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www.wattsdrainage.ca
Ex. WUCO-11/2
Order Code: WUCO-
1-1/2" (38)
2" (51)
3" (76)
4" (102)
4" (102)
4" (102)
6" (178)
7" (178)
"B" COVER SIZEPLUG SIZE
6" (152) 9" (229)
6"(152) Plug Size 6
197
CANADA
URINAL
Contractor: Lumech Plumbing & Heating LTD. Job: Boys & Girls Club Reno. Prince Of Wales