NRDA F-1
NAYA RAIPUR DEVELOPMENT AUTHORITY
Tender Document for the
Integrated Infrastructure Development for phase 1 works of
Sector 12, 40 & other specified areas at Naya Raipur
(Following Three-Envelope Tender Procedure)
Schedule – A Price Tender
To be submitted in ENVELOPE-3
NIT No : 133/IID/S-12, 40 & SA. ( Phase-I) /EEC-III/ CE (E)/ NRDA / 2016-17,Naya Raipur, Dated: 10.11.2016
Issued by: Chief Executive Officer,
Naya Raipur Development Authority (NRDA)
Paryavas Bhawan, North Block Sector- 19,
Naya Raipur- 492 002, Chhattisgarh
Tel No: + 91 771 2512500; Fax No.: +91 771 2512400.
Website: www.nayaraipur.gov.in
Integrated Infrastructure Development for phase 1 works of Sector 12, 40 & other specified areas at Naya Raipur NRDA
Signature of Contractor…………………………….... Signature of NRDA………………………..…………
Tender Document Contains (a) Only schedule “A” and Section-I of schedule “D” are to be filled & singed by the tenderer (b) All the certificates as per pre qualification criteria shall be appended with relevant forms of schedule”D”
1. PART ONE (NRDA F-1)-(Attached herewith, to be submit along the tender) Part (A)
a) Press Notice
b) Detailed NIT
Part (B)
a) Schedule-A
(i) Cost Abstract
(ii) Bill of Quantities
b) Schedule-B –NIL
c) Schedule-C –NIL
d) Schedule-D
Section-I................ Technical tender forms
(i) Letter of Technical Tender
(ii) Tenderer’s Information Sheet
(iii) Annual Turnover
(iv) Specific Construction Experience
(v) Declaration
(vi) Check list for Technical tender evaluation
Section –II ……………....Scope of work
Section –III..................... Technical specifications of work
Section –IV.................... Special Conditions of Contract
Section –V.................... List of approved makes
Section –VI..................... Drawings
e) Schedule-E
f) Schedule-F
2. PART TWO (NRDA F-2/3) )-Standard form (Not Attached herewith, and not to be submitted along the tender) Important note: - Link site http:// nayaraipur.com/documents/gcc.pdf
1. General Guidelines
2. Tender
3. General rules and directions
4. Conditions of contract
5. Clauses of contract
6. Model rules relating to labour, water supply and sanitation in labour camps safety code
7. Contract forms
(a) Draft Format for Performance Security
(b) Earnest Money Deposit Form (Bank Guarantee)
(c) Format of Contract Agreement
(d) Draft Format for Performance Guarantee for Water Proofing and Anti-termite Works
(e) Indemnity Bond
(f) Indenture Bond
(g) Notice for Appointment of Arbitrator
8. Proforma of schedules (Schedule ’A’ to Schedule ’F’)
Integrated Infrastructure Development for phase 1 works of Sector 12, 40 & other specified areas at Naya Raipur NRDA
Signature of Contractor…………………………….... Signature of NRDA………………………..…………
Naya Raipur Development Authority (NRDA)
Raipur, Chhattisgarh
Document details
Name of work : “Integrated Infrastructure Development for phase 1 works of Sector 12, 40 & other
specified areas at Naya Raipur”
Name of Tenderer:
Details
a) Cost of Tender Document : Rs
b) EMD : Rs
Signature of Tenderer
Date:____________
Sl. No. Description of Items Amount ( in INR) Amount in Words ( In INR )
A ROAD WORK Rs. -
B
UTILITY SERVICES: WATER SUPPLY, SEWERAGE
SYSTEM, DRAINAGE SYSTEM, UTILITY CROSSINGS,
BRIDGE CONSTRUCTION, NALA REALIGNMENT AND
TRAINING WORK, PARK DEVELOPMENTS &
ELECTRICAL DUCT ETC.
Rs. -
C ELEECTICAL WORK Rs. -
D AUTO TAXI STAND Rs. -
Total Amount in INR Rs. -
Cost abstract for
Integrated Infrastructure Development Works for Phase-I works at sector-12, 40 and other Specified areas at Naya Raipur
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
A ROAD WORKS
1
Detailed survey of existing road including chaining, leveling,
with cross section at 25.0 m intervals and closing survey each day's
work,supply and of fixing bench marks, painting, taking trial pits
and submission of road cross sections, L-sections, quantity
statements in computerized prints in five copies in proper files and
all type of compliance required by the Engineer-in-charge.
Km. 26.17 Rs. -
2
Excavation in Soil (by Mechanical Means). Excavation for
roadway / drain in soil using mechanical means including loading
in tipper for carrying of cut earth to embankment site and unloading
with all lifts and lead as per relevant clauses of section 300.
Cum. 3,09,626.67 Rs. -
3
Cutting of trees, including cutting of trunks, branches and removal
of stumps, roots, stacking of serviceable material with all lifts and
lead and earth filling in the depression/pit and as per relevant
clauses of section-200 for :-
Each 149.00 Rs. -
Bill of Quantity
Integrated Infrastructure Development Works for Phase-I works at sector-12, 40 and other Specified areas at Naya Raipur
2 of 109
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
4
Clearing and grubbing road land including uprooting rank
vegetation, grass, bushes, shrubs, saplings and trees girth up to 300
mm, removal of stumps of trees cut earlier and disposal of
unserviceable materials and stacking of serviceable material to be
used or auctioned up to all lifts and lead including removal and
disposal of top organic soil not exceeding 150 mm in thickness if
required and as per relevant clauses of section-200. (A) In area of
light jungle
Hectare. 14.85 Rs. -
5
Construction of embankment / sub-grade with Material
Obtained from Borrow Pits (Construction of embankment with
approved material/selected soil having C.B.R. (as specified in the
contract and construction drawings) obtained from borrow pits with
all lifts and leads, transporting to site, spreading, grading to
required slope and compacting to meet requirement of table 300-2)
as specified by in the drawigns and Engineer in charge.
Cum. 3,39,033.89 Rs. -
6
Compacting Original Ground (ii) Compacting Original
Ground supporting sub-grade Loosening and compacting
original ground to facilitate placment of first layer of embankment
scarified to a depth of 150mm mixed with water at O.M.C and then
compacted by rolling so as to achieve minimum dry density as
given in table 300-2 for embankment construction
Cum. 29,871.28 Rs. -
3 of 109
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
7
Construction of Embankment with Material Deposited from
Roadway Cutting (Construction of embankment with approved
materials having C.B.R. (as specified in the contract) deposited at
site from roadway cutting and excavation from drain and
foundation of other structures graded and compacted to meet
requirement of table 300-2)
Cum. 43,945.44 Rs. -
8
Granular Sub-base as per Table:- 400-1Construction of granular
sub-base by providing close graded Material, , carriage of mixed
Material to work site, spreading in uniform layers with motor
grader on prepared surface watering, rolling and compacting with
vibratory power roller at OMC to achieve the desired density,
complete as per clause 401 . (A) Plant mix method (with
Mechanically crushed stone only) (iii) for grading-III Material
Cum. 66,743.21 Rs. -
9
Wet Mix Macadam (Providing, laying, spreading and compacting
graded stone aggregate to wet mix macadam specification including
premixing the Material with water at OMC in mechanical mix plant
carriage of mixed Material by tipper to site, laying in uniform
layers with paver in sub- base / base course on well prepared
surface and compacting with vibratory roller to achieve the desired
density as per clause 406.)
Cum. 58,625.90 Rs. -
4 of 109
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
10
Dense Bituminous Macadam(Providing and laying dense
bituminous macdam with minimum 40-60 TPH capacity HMP
using crushed aggregates of specified grading, premixed with
bituminous binder @4.0 to 4.5% by weigth of toal mix of mix and
filler, transporting the hot mix to work site laying with hydrostatic
paver finisher to the required grade, level and alignment, rolling
with smooth wheeled, vibratory and tandem rollers to achieve the
desired compaction as per MORTH specification clause N0.505
complete in all aspects.) A. (ii) with sensor paver finisher for
Grading -II(26.5mm nominal size bitumen content 4.50%)
Cum 11,676.64 Rs. -
11
Bituminous Concrete ( providing and laying bituminous concrete
with minimum 40-60 TPH capacity hot mix plant using crushed
aggregates of specified grading, premixed with bituminous binder
@ 5.0 to 6.0% by weight of total mix of mix and filler, transporting
the hot mix to work site, laying with a hydrostatic paver finisher
with sensor control to the required grade, level and
alignment,rolling with smooth wheeled, vibratory and tandem
rollers to achieve the desired compaction as per MORTH
specification caluse No.507 complete in all repsects) A.(iii) with
sensor paver finishere for Grading -II(13.2mm nominal size) with
bitumen 6.0%
Cum 9,342.75 Rs. -
12
Prime Coat ( Providing and applying primer coat with oil based
bitumen emulsoion (SS-I, grade confirming to IS:8887) on
prepared surface of granular Base including clearing of road
surface and spraying primer using mechanical means as per cluse
502.
5 of 109
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
a (i) on WBM/WMM surface @0.85 Kg/sqm. 2,33,464.61 Rs. -
13
Tack Coat Providing and applying tack coat with bitumen
emulsion(RS-1, grade confirming to IS:8887) using emulsion
pressuredistributor on the prepared bituminous/granular surface
cleaned withmechanical broom and as per clause 503.
Sqm
a (i) Bituminous surface @ 0.25 kg /Sqm 2,33,464.61 Rs. -
b (i) Granular surface treated with prime @ 0.30 kg /Sqm 2,33,464.61 Rs. -
14
Cement Concrete Pavement (Construction of un-reinforced, dowel
jointed, plain cement concrete pavement over a prepared sub-base,
coarse and fine aggregate conforming to IS:383, and graded as per
table 600-3, mixed as per approved mix design at site, laid,
Cum 2,021.90 Rs. -
6 of 109
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
15
Dry Lean Cement Concrete Sub-base as per IRC:SP-49
(Construction of dry lean cement concrete Sub-base over a
prepared sub-grade with coarse and fine aggregate conforming to
IS: 383, the size of coarse aggregate not exceeding 26.5 mm,
aggregate cement rati
Cum 1,011.00 Rs. -
16
Providing & Laying precast Interlocking concrete blocks of
minimum compressive strength of 300kg/sq.cm and approved size,
shape /pattern over coarse sand bed of thickness upto 40mm and
joints thick filled with fine sand includind leveling with surface
vibrator, temping and sweeping etc .complete as per IRC-SP-63-
2004
Sqm 98,607.29 Rs. -
15
Cast insitu Cement Concrete M20 Kerb with Channel(
construction of cement concrete kerb with channel with top and
bottom width 115 and 165mm repectively, 250mm high in M20
grade PCC on M10 grade foundation 150mm thick , kerb channel
300mm wide, 50mm thick in PCC M20 grade, sloped towards the
kerb, kerb stone with channel laid with kerb laying machine,
foundation concrete laid manually all complete as per clause 409).
Meter 33,912.23 Rs. -
7 of 109
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
17
Cast in Situ Cement Concrete M20 kerb (Construction of
cement concrete kerb with top and bottom width 115 and 165 mm
respectively, 250 mm high in M20 grade PCC on M10 grade
foundation 150 mm thick, foundation having 50 mm projection
beyond kerb stone, kerb stone laid with kerb laying machine,
foundation concrete laid manually, all complete as per clause 408)
Meter 37,476.02 Rs. -
18
Painting on Concrete Surfaces (A)Two coats on new surfaces
(Painting two coats after filling the surface with synthetic enamel
paint in all shades on new plastered concrete surfaces)
Sqm 26,991.72 Rs. -
19
Boundary pillar (Reinforced cement concrete M15 grade boundary
pillars of standard design as per IRC:25-1967, fixed in position
including finishing and lettering but excluding painting)
each 103.31 Rs. -
20
Road Marking with Hot Applied Thermoplastic Compound
with Reflectorizing Glass Beads on Bituminous Surface
(Providing and laying of hot applied thermoplastic compound 2.5
mm thick including reflectorizing glass beads @ 250 gms per sqm
area, thickness of 2.5 mm is exclusive of surface applied glass
beads as per IRC:35-1997. The finished surface to be level,
uniform and free from streaks and holes.)
Sqm 14,036.34 Rs. -
8 of 109
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
21
Retro- reflectrorized Traffic signs (Providing and fixing of retro-
reflectrorized cautionary, mandatory and informatory sign as per
IRC:67-2012 made of encapsulated lens type reflective sheeting
vide clause 801.3, fixed over aluminum sheeting, 1.5 mm thick
supported on a mild steel frame of size 40 x 40 x 5 mm and mild
steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the
ground by means of properly designed foundation with M15 grade
cement concrete 45 cm x 45cm x 60cm, 60 cm below ground level
as per approved drawing)
a 60 cm x 45 cm rectangular Each 65.00 Rs. -
b 60 cm equilateral triangle Each 65.00 Rs. -
c 60 cm Circular 64.00 Rs. -
d 90 cm high octagon Each 67.00 Rs. -
Sub Total of Road Works Rs. -
9 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
B UTILITY SERVICES
1
Earth work in excavation for pipe trench in all type soil
areas including dressing, watering and ramming and
disposal of excavated earth with all lead and lift, disposal
earth to be leveled, neatly dressed including clearing of
vegetation, shoring, strutting, de-watering, bailing of
water met due to all causes including lowering of water
table required to keep the trench in the dry condition to
facilitate for laying, jointing and testing of works and
backfilling with approved materia, all complete as per
technical Specifications and as per direction of Engineer.
i upto 1.5 m deep Cum 2,07,735.49 Rs. -
2
Earth work in excavation for pipe trench in ordinary soil
areas including dressing, watering and ramming and
disposal of excavated earth with all lead and lift, disposal
earth to be leveled, neatly dressed including clearing of
vegetation, shoring, strutting, de-watering, bailing of
water met due to all causes including lowering of water
table required to keep the trench in the dry condition to
facilitate for laying, jointing and testing of works all
complete as per technical Specifications and as per
direction of Engineer.
i >1.5m and upto3.0m deep Cum 45,056.97 Rs. -
Bill of Quantity
Integrated Infrastructure Development Works for Phase-I works at sector-12, 40 and other Specified areas at Naya Raipur
Page 10 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii >3.0m and upto 4.5m deep Cum 22,945.00 Rs. -
3
Earth work in excavation for pipe trench in Hard Soil
areas including dressing, watering and ramming and
disposal of excavated earth with all lead and lift, disposal
earth to be leveled, neatly dressed including clearing of
vegetation, shoring, strutting, de-watering, bailing of
water met due to all causes including lowering of water
table required to keep the trench in the dry condition to
facilitate for laying, jointing and testing of works all
complete as per technical Specifications and as per
direction of Engineer.
i >1.5m and upto 3.0m deep Cum 4,736.00 Rs. -
ii >3.0m and upto4.5m deep Cum 2,405.00 Rs. -
4
Earth work in excavation for pipe trench in all kinds of
rocks in areas including dressing, stacking of useful
material and disposal of unserviceable one up to 50 m
lead and lift up to 4.5m. all complete as per technical
Specifications and as per direction of Engineer.
i Hard rock requiring blasting. Cum 60.00 Rs. -
Page 11 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
iiHard rock requiring chiselling / where blasting is
prohibited.Cum 60.00 Rs. -
5
Filling available excavated earth in trenches, plinth sides
of foundation in layers not exceeding 20cm. in depth
including consolidation of each layer by ramming
watering, lead upto 50m and lift up to all depth in all
kinds of soils all complete as per technical Specifications
and as per direction of Engineer.
cum 80,774.00 Rs. -
6
Providing and filling in plinth with sand/ Crusher dust
under floor in layers not exceeding 20cm in depth
consolidating each deposited layer by ramming and
watering, including dressing etc. complete.
cum 7,964.62 Rs. -
7
Providing and laying nominal mix plain cement concrete
with crushed stone aggregate using concrete mixer in all
works upto plinth level excluding cost of form work. all
complete as per technical Specifications and as per
direction of Engineer.
i1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 40mm nominal size).Cum 2,589.23 Rs. -
ii1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 40mm nominal size).cum 176.00 Rs. -
Page 12 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
8
Construction of RCC drain/ chamber/ Thrust
block/Encasement/tanks/cover/park works etc. placing in
position, providing shuttering and concreting by using
concrete mixer, compaction by vibration etc complete as
per drawings and technical specifications excluding
reinforcement.
i RCC M-20 Cum 24,118.10 Rs. -
9
Providing and laying design mix reinforced cement
concrete with crushed graded stone aggregate 20mm
nominal size using batching plant, transit mixer and
concrete pump, in all works upto plinth level excluding
cost of form work. all complete as per technical
Specifications and as per direction of Engineer.
i RCC M-20 Cum 1,365.00 Rs. -
10
Providing,laying and placing of precast cement concrete
cover of drain M-35 grade in superstructure including
form work but excluding reinforcement complete .
Cum 87.98 Rs. -
11
Providing and fixing form work including centring,
shuttering, strutting, staging, propping bracing etc.
complete and including its removal at all levels, for:
i
Foundations, footings, bases of columns plinth beam,
curtain wall in any shape and size and all type of wall
below plinth level.
Sqm 3,984.50 Rs. -
Page 13 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
iiColumns, Pillars, Piers and likes- rectangular or square in
shapeSqm 54.00 Rs. -
iiiSuspended floors, roofs, access platform, balconies (plain
surfaces) and shelves (cast in situ) Sqm 24.00 Rs. -
iv Beams, lintels, cantilevers & walls sqm 30.15 Rs. -
12
Providing and mixing water proofing material in PCC/ RCC
work in the proportion recommended by the
manufacturer. all complete as per technical Specifications
and as per direction of Engineer.
kg 23.94 Rs. -
13
Providing and placing in position reinforcement for R.C.C.
work including straightening, cutting, bending, binding
etc. complete as per drawings including cost of binding
wire in foundation and plinth all complete as per
technical Specifications and as per direction of Engineer.
i Thermo-Mechanically Treated bars FE -500D kg 18,15,906.27 Rs. -
Page 14 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
14
Providing, laying, Jointing & field testing of High Density
Polyethylene pipes, (HDPE) Conforming to IS4984/ 14151/
12786/ 13488 including all accessories (for specials
10kg/sq.cm) i.e. tees, bends, reducers, end caps etc and
fittings with necessary jointing material like mechanical
connector or jointing pipes by heating to the ends of
pipes with the help of Teflon coated electric mirror/
heater to the required temperature and then pressing the
ends together against each other, to form a monolithic &
leak proof joint by thermo setting process. It may be
required to be done with Jacks/ Hydraulic Jacks /But
fusion machine. (50mm & above fusion jointed & below
50 mm mechanical jointed) all complete as per technical
Specifications and as per direction of Engineer.
i 75 mm dia.(PE-100) 6 Kg/sq.cm Rm 4,740.00 Rs. -
ii 110 mm dia.(PE-100) 6 Kg/sq.cm Rm 11,050.00 Rs. -
iii 160 mm dia.(PE-100) 6 Kg/sq.cm Rm 10,630.00 Rs. -
iv 200 mm dia.(PE-100) 6 Kg/sq.cm Rm 15,170.00 Rs. -
Page 15 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
15
Providing, laying and jointing socket & spigot centrifugally
cast (Spun) Ductile Iron pressure pipes with inside cement
mortar lining (classK-7) Conforming to IS8329/2000 with
suitable Rubber Gasket (Pushon) joints as per IS:5382/85
including testing of joint (laying Conforming to IS 12288 :
1987) all complete as per technical Specifications and as
per direction of Engineer.
i 300mm diameter Rm 12,450.00 Rs. -
ii 400mm diameter Rm 800.00 Rs. -
Page 16 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
16
Providing & Supplying D.I. Specials & Fittings For all types
of specials, bends, reducers, tees. etc. all complete as per
technical Specifications and as per direction of Engineer.
i 80 to 300 mm dia Kg 12,336.00 Rs. -
ii 350 mm and above dia Kg 589.00 Rs. -
17
Providing, laying and jointing of pig lead at site of work.
all complete as per technical Specifications and as per
direction of Engineer.
quintal 0.55 Rs. -
18
Providing & fixing of Cast iron double flanged sluice valves
as per I.S.:14846-2000 fitted with cast iron cap including
jointing & testing with cost of jointing material such as
bolts, nuts, rubber insertions etc. all complete. (Steel
Spindle) all complete as per technical Specifications and
as per direction of Engineer.
i 80 mm diameter (Pressure rating PN - 1.6) Each 12.00 Rs. -
Page 17 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 100 mm diameter (Pressure rating PN - 1.6) Each 50.00 Rs. -
iii 150 mm diameter (Pressure rating PN - 1.6) Each 17.00 Rs. -
iv 200 mm diameter (Pressure rating PN - 1.6) Each 24.00 Rs. -
v 300 mm diameter (Pressure rating PN - 1.6) Each 16.00 Rs. -
vi 400 mm diameter (Pressure rating PN - 1.6) Each 3.00 Rs. -
19
Providing & fixing cast iron double air valves, flanged
without in-built isolating valve as per IS:14845-2000
including jointing & testing with cost of jointing material
and rubber insertion all complete as per IS :13095-1991
all complete as per technical Specifications and as per
direction of Engineer.
i 80 mm dia PN-1.6 Each 4.00 Rs. -
Page 18 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 100 mm dia PN-1.6 Each 18.00 Rs. -
20
Providing, Laying & Jointing of welded double flanged
centrifugal cast (spun)ductile Iron pressure pipes
Conforming to IS:8329/2000 in the length of 1m. For class
K-9 with inside cement mortar lining for the sizes /dia
pipes. (laying Conforming to IS 12288 : 1987) all complete
as per technical Specifications and as per direction of
Engineer.
i 80mm Each 2.00 Rs. -
ii 100mm Each 11.00 Rs. -
21
Providing, Laying & Jointing of welded double flanged
centrifugal cast (spun)ductile Iron pressure pipes
Conforming to IS:8329/2000 in the length of 2m. For class
K-9 with inside cement mortar lining for the sizes /dia
pipes. (laying Conforming to IS 12288 : 1987) all complete
as per technical Specifications and as per direction of
Engineer.
i 80mm Each 2.00 Rs. -
Page 19 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 100mm Each 15.00 Rs. -
Page 20 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
22
Providing & Laying Ductile Iron Double Socket branch
flange Tee Conforming to IS-9523/2000 having dimension
as per table 21 of IS-9523/2000 in the nominal
diameter/sizes with external bitumen coating and internal
cement mortar lining with finishing as per clause 13 of IS-
9523/2000. (laying Conforming to IS 12288 : 1987) (All
sizes in mm) all complete as per technical Specifications
and as per direction of Engineer.
i 150x80 Each 2.00 Rs. -
ii 200x80 Each 1.00 Rs. -
iii 300x100 Each 14.00 Rs. -
iv 400x100 Each 1.00 Rs. -
23
Providing, laying, jointing, testing and commissioning of
D.I Dismantling joint with M.S. Nut stud & washers coated
for rust prevention & internal rubber rings etc. complete
assembly set as per type design inclusive of all taxes &
duties, insurance, loading/ unloading & stacking FOR at
site all complete as per technical Specifications and as per
direction of Engineer.
Page 21 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
i 80 mm diameter Each 10.00 Rs. -
ii 100 mm diameter Each 50.00 Rs. -
iii 150 mm diameter Each 19.00 Rs. -
iv 200 mm diameter Each 24.00 Rs. -
v 300 mm diameter Each 16.00 Rs. -
vi 400 mm diameter Each 2.00 Rs. -
Page 22 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
24
Providing 1st class bedding below pipes with graded sand
or other granular materials passing through 5.6 mm sieve
as per clause 2904. all complete as per technical
Specifications and as per direction of Engineer.
Cum 19,399.00 Rs. -
25
Supply, installation, testing and commissioning of
electromagnetic full bore meter complete as per specification
including transportation to site, storage, safety, installation,
testing, commissioning, making connections with existing pipe
line, including excavation at site, cuts in the existing pipe system,
dewatering and reinstating the same after completion of
installation as per specification and drawings including all taxes.
Accuracy of meter +/- 0.3% - 0.5% of measured value, Flange
connection as per AWWA & IS, fully welded sensor housing
complying to IP 68 standard, Electrodes SS 316/Hastelloy C, cable
gland 1/2" NPT, Sensor housing fully welded SS 304 housing with
protective Polyurethane paint/Die Cast Aluminium with anti
corrosive grade paint/Carbon Steel ASTM A 105 with corrosion
resistant two component epoxy coating (min 150 µm), Flow
Transmitter/ Converter: Microprocessor based, modular design
display 2 line back lit LCD for indication of actual flow rate,
forward, reverse, sumtotalizer, Perfection category: IP 65.
Output: One current output (4-20 mA) one scalable pulse output.
The required cable and mounting accessories for remote type
transmitter mounting shall be included (Maximum distance of 30
meters or as per site condition).Instrument shall be based on
open protocol and SCADA compatible, complete in all respect as
per technical specification including all specials and fittings and as
per direction of Engineer in Charge.
i EFM 50 for DN 50mm Each 8.00 Rs. -
Page 23 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii EFM 80 for DN 80mm Each 6.00 Rs. -
iii EFM 100 for DN 100mm Each 1.00 Rs. -
iv EFM 150 for DN 150mm Each 4.00 Rs. -
v EFM 200 for DN 200mm Each 1.00 Rs. -
vi EFM 300 for DN 300mm Each 3.00 Rs. -
26
Supply, installation, testing and commissioning of Dirt Box
with S.S. Strainer as per specifications (Dia in mm) as
required all complete as per technical Specifications and
as per direction of Engineer.
i 15 mm nominal outer dia pipes Each 3.00 Rs. -
ii 20 mm nominal outer dia pipes Each 3.00 Rs. -
Page 24 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
iii 40 mm nominal outer dia pipes Each 3.00 Rs. -
iv 50 mm nominal outer dia pipes Each 8.00 Rs. -
v 80 mm nominal outer dia pipes Each 6.00 Rs. -
vi 100 mm nominal outer dia pipes Each 1.00 Rs. -
vii 150 mm nominal outer dia pipes Each 4.00 Rs. -
viii 200 mm nominal outer dia pipes Each 1.00 Rs. -
ix 300 mm nominal outer dia pipes Each 3.00 Rs. -
Page 25 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
27
Construction of RCC valve chamber internal size 1.2m x
1.2m x 1.5m, 100mm thick PCC- M10 and RCC M20 grade
150mm thick wall, precast cover 125mm thick slab on top
for protection of valve coming under traffic & extended
MS valve operating spindle rod as reqd etc. Including
steel reinforcementon 10mm dia. 150mm c/c bothways
wall & precast cover, shuttering, labour charges etc as
per drawing and as per direction of Engineer complete
etc.
No 131.00 Rs. -
28
Construction of RCC valve chamber internal size 2.5m x
1.2m x 1.5m, 100mm thick PCC- M10 and RCC M20 grade
150mm thick wall, precast cover 125mm thick slab on top
for protection of valve coming under traffic & extended
MS valve operating spindle rod as reqd etc. Including
steel reinforcementon 10mm dia. 150mm c/c bothways
wall & precast cover, shuttering, labour charges etc as
per drawing and as per direction of Engineer complete
etc.
No 8.00 Rs. -
29
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)
pipes, having thermal stability for hot & cold water supply
including all CPVC plain & brass threaded fittings. This
included jointing of pipes & fittings with one step CPVC
solvent cement, trenching, refilling & testing of joints
complete as per direction of Engineer in Charge.
a EXTERNAL WORK
i 15 mm nominal outer dia pipes Rm 65.00 Rs. -
ii 20 mm nominal outer dia pipes Rm 1,430.00 Rs. -
Page 26 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
iii 25 mm nominal outer dia pipes Rm 50.00 Rs. -
iv 32 mm nominal outer dia pipes Rm 645.00 Rs. -
v 40 mm nominal outer dia pipes Rm 15.00 Rs. -
vi 50 mm nominal outer dia pipes Rm 250.00 Rs. -
vii 100 mm nominal inner dia pipes Rm 3.00 Rs. -
30
Providing and Supplying of following G.I. Specials as per
relevant IS1239, ISI marked for usage in Drinking water
inclusive of all materials, Central, State and Municipal
taxes and duties inspection charges, transit insurance,
loading/unloading FOR site unloading & stacking etc.
complete as per direction of Engineer-in-Charge.
M.S.Saddle Piece
i 15 Each 15.00 Rs. -
Page 27 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 20 Each 285.00 Rs. -
iii 25 Each 10.00 Rs. -
iv 32 Each 300.00 Rs. -
v 50 Each 15.00 Rs. -
vi 100 Each 1.00 Rs. -
31
Providing and Supplying of Saddle Piece, duly tested from
certified agencies for usage in Drinking water inclusive of
all materials, Central, State and Municipal taxes and
duties inspection charges, transit insurance, loading /
unloading FOR site unloading & stacking etc. complete as
per direction of Engineer-in-Charge.
i 160 x 32 mm dia Each 30.00 Rs. -
Page 28 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 110 x 20 mm dia. Each 3.00 Rs. -
iii 110 x 32 mm dia. Each 100.00 Rs. -
iv 110 x 40 mm dia. Each 3.00 Rs. -
v 110x 50 mm dia. Each 5.00 Rs. -
Page 29 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
32
Providing and fixing GM or brass ferrules Conforming to IS-
2692/1984 (Reaffirmed2005), tested to 21.00kg/sq.cm.
i/c boring and tapping the main all complete as per
technical Specifications and as per direction of Engineer.
i 32 mm dia. Each 25.00 Rs. -
ii 40 mm dia. Each 10.00 Rs. -
iii 50 mm dia. Each 1.00 Rs. -
33
Providing and fixing ball valve (brass) of approved quality,
High or low pressure, with plastic floats complete : all
complete as per technical Specifications and as per
direction of Engineer.
i 15 mm dia each 15.00 Rs. -
ii 20 mm dia each 288.00 ` Rs. -
Page 30 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
iii 25 mm dia each 10.00 Rs. -
34
Providing and fixing brass/ gun metal gate valve with C.I.
wheel of approved quality (screwed end): all complete as
per technical Specifications and as per direction of
Engineer.
i 32 mm dia each 15.00 Rs. -
ii 40 mm dia each 3.00 Rs. -
iii 50 mm dia each 21.00 Rs. -
35
Supply, installation, testing and commissioning of Multi
Jet, dry-dial, inferential type, horizontal, Magentically
coupled, class 'B'water meters Conforming to IS-779:
1994 and ISO 4064:1993 standard with EEC/MID
certification mark, with IP68 protection class copper can
register with 5 mm tempered mineral glass cover,
successful Life Cycle Test Certificate from FCRI and AMR
compatibility with 5 years warranty complete with brass
nuts and nipples. Instrument shall be complete in all
respects according to technical specifications including all
specials
i 15 mm nominal outer dia pipes Each 3.00 Rs. -
Page 31 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
Page 32 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 20 mm nominal outer dia pipes Each 3.00 Rs. -
iii 40 mm nominal outer dia pipes Each 3.00 Rs. -
36
Constructing masonry Chamber 60x60x75 cm, inside with
modular well burnt clay bricks of 35 kg/ cm² in cement
mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,
with C.I. surface box 100mm. top diameter, 160 mm
bottom diameter and 180 mm deep (inside) with chained
lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand :
4 graded stone aggregate 20mm nominal size) necessary
excavation foundation concrete 1:5:10 (1 cement : 5 fine
sand : 10 graded stone aggregate 40 mm nominal size)
and inside plastering with cement mortar 1:3 (1 cement :
3 coarse sand) 12 mm thick finished with a floating coat
of neat cement complete as per standard design : all
complete as per technical Specifications and as per
direction of Engineer.
Each 16.00 Rs. -
37
Constructing masonry Chamber 90x90x100 cm, inside
with modular well burnt clay bricks of 35 kg/ cm² in
cement mortar 1:4 (1 cement : 4 coarse sand) for sluice
valve, with C.I. surface box 100mm. top diameter, 160
mm bottom diameter and 180 mm deep (inside) with
chained lid and RCC top slab 1:2:4 mix (1 cement : 2
coarse sand : 4 graded stone aggregate 20mm nominal
size) necessary excavation foundation concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40 mm
nominal size) and inside plastering with cement mortar
1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a
floating coat of neat cement complete as per standard
design :
Each 309.00 Rs. -
Page 33 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
38
Meter box and cover : Supply, installation, testing and
commissioning of UV resistant, high density polyethylene
material size: length 870mmx width=655mm x depth
690mm, yet lightweight, specially designed to withstand
light vehicle load. Ease of opening and closing of top
cover shall be ensured with locking arrangement and
enclosure shall have enough mechanical strength
including cement concrete foundation 1:3:6 (1 cement : 3
coarse sand : 6 graded stone aggregate 40mm nominal
size), size of foundation= 1100X900X400mm and
formwork shuttering & removing all complete as per
standered specifications, and as per direction of
Engineer.
Each 10.00 Rs. -
Page 34 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
Mechanical and Electrical works
39
Providing and Supplying of following Open well
submersible Pump set with ISI mark IS14220 (horizontal)
without panel board, duly tested from certified agencies
for usage in Drinking water inclusive of all materials,
Central, State and Municipal taxes and duties inspection
charges, transit insurance, loading/unloading FOR site
unloading & stacking etc. complete as per direction of
Engineer-in-Charge.
aSubmersible pump 150mm dia. (with Bronze Impeller)up
to 12 stages
i 20 HP, 1250 LPM at a head of 40 metres, Each 12.00 Rs. -
40
Supplying and laying following sizes one number PVC
insulated, PVC sheathed, steel armoured, aluminium
conductor power cable of 1.1 KV grade direct in ground
including excavation, sand cushioning, protective covering
and refilling the trench etc as required.
i 4 x 16 sq. mm. Meter 240.00 Rs. -
Page 35 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
41
Supply, installation, testing and commissioning of cubicle
type wall/ floor mounted power cum control panel made
out of not less than 1.6 mm thick MS sheet and
comprising of following panel mounting switchgears there
in including connection inter-connection etc. as required.
a) Phase indicating lamps with fuses and toggle switches 1
set b) Star-delta starter suitable for 7.5 HP 3 phase AC
induction motor with over load and no volt relay c) 32 A
"C" series TPMCB 1 No d) Voltmeter 0-500 V with selector
switch 1 set e) Ammeter 0-10 A with CT's and selector
switch 1 set. all complete as per technical Specifications
and as per direction of Engineer.
Set 6.00 Rs. -
42
Supplying and installing pressure gauge of 100 mm Ø., 0-
300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø.
pad cock valve, and G.I. pipe, elbow etc. as per
requirement in approved manner. all complete as per
technical Specifications and as per direction of Engineer.
Each 12.00 Rs. -
43
Supply, erection, jointing, testing & commissioning of "C"
Class MS pipes (as per IS: 1239) including necessary
specials such as tees, bends, flanges reducers etc.,
complete on wall/ ceiling. The pipes to be erected on wall
or suspended from beams, RCC roof slabs with suitable
size MS bars/ angle irons including painting of metal part
except pipe line. all complete as per technical
Specifications and as per direction of Engineer.
i 80mm dia. Rm. 303.00 Rs. -
Page 36 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 100mm dia. Rm. 11.00 Rs. -
44
Fabrication of M.S. Pipes, grils and Specials: Fabrication
of M.S. pipes & specials as per IS specifications with inside
& outside epoxy coating as per relevant IS code, duly
tested for usage in Drinking water inclusive of all
materials, Central, State and Municipal taxes and duties in
spection charges, transit insurance, loading / unloading
FOR site unloading & stacking etc. complete as for
direction of Engineer-in-Charge. (all thickness) all
complete as per technical Specifications and as per
direction of Engineer.
MT 6.60 Rs. -
45
Painting for M.S. pipe with a coat of red oxide primer and
two or more coats of synthetic enamel paint of approved
colour and Quality to give an even shade including surface
preparation.
i 80mm dia. Rm 300.00 Rs. -
46
Providing and fixing following cast iron double flanged
single door reflux (non return) valve including jointing and
testing with cost of jointing material such as bolts, nuts
and rubber insertion all complete as per IS:5312 9 (Part I)
i 80 mm dia. (Class -PN 1.0 rating) No 12.00 Rs. -
Page 37 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
47
Providing, laying, Jointing & field testing of DWC HDPE
Pipes (with external annular corrugation and smooth
internal walls) duly tested Conforming to IS 16098 (PART-
II): 2013 having stiffness class of SN 8 with ring stiffness
not less than 8.00KN/SQM. and impact resistance TIR
valve not more than 10% including necessary jointing
materials for non-pressure underground sewerage,
drainage & cross drainage application. Inclusive of all
taxes related to central, state and municipal, inclusive of
excise duty, inspection charges, transportation charges,
transit insurance, loading/unloading and stacking at
site/store etc. and as per Technical Specifications and as
per direction of Engineer.This is also inclusive of Jointing
material i.e Pipe with online/offline coupler and
elastomeric sealing ring. All the joints shall be confirmed
water tight as per standards.
i 250/295 mm dia. RM 500.00 Rs. -
ii 300/345 mm dia. RM 5,300.00 Rs. -
iii 400/480 mm dia. RM 13,800.00 Rs. -
iv 600/715 mm dia. RM 4,800.00 Rs. -
Page 38 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
Construction of prefabricated HDPE manhole:
Supplying , Installation testing and commissioning of
prefabricated HDPE manhole: Providing, lowering, laying,
aligning, fixing in position at all level/ depths High Density
Poly Ethylene (HDPE) manhole conforming to EN 13598-
2:2009, man entry type of 1000mm diameter for depth
specified below, shall be of single wall construction OR
modular construction conforming to EN 681-1 with triple
safety seal (three side lip/element) made of 100% virgin
PE material without recycling or foam content, including
connecting the according to EN 681-1 and the manholes
shall be safeguarded against uplift pressure with solid
horizontal reinforcement ribs of appropriate thickness
and with at regular intervals all along the outside of the
manhole.( Make : VECTUS INDUSTRIES LTD / equivalent)
48
Page 39 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
The item is inclusive of Excavation, Dewatering, Layerwise
backfilling and compaction of grannular material ,
Provision of corrosion resistant steps at a vertical distance
of 25cm .Providing and fixing of FRP Manhole frame and
cover with locking arrangement fitting to 600mm dia
manhole openings and load should be carry 20tone
approved brand and as per IS:1726:1991etc.
Providing and fixing of Precast RCC M35 grade load
distribution ring 1050mm OD & 635mmID and designed
to handle heavy load as approved by Engineer placed
around the neck of the manhole of 150mm thickness
including reinforcement. Providing RCC M20 grade
concrete thick 200mm slab (Dia 1500mm outer dia and
inner dia 635mm ) around the manhole below the
Precast RCC distribution Ring. Providing and laying
Manhole bottom PCC (1:3:6) of 200mm thick and 1.5m
dia. All the inlet, outlet connections to the manhole shall
be complete with all accessories/ fittings, material,
labour, jointing materials , testing and commissioning as
per detailed drawing, as per Technical specifications and
all complete as directed by Engineer in charge.
1000 mm diameter circular manhole
i Manhole of depth up to 1.2m No 70.00 Rs. -
ii For depth above 1.2m and up to 1.8m No 60.00 Rs. -
iii For depth above 1.8m and up to 2.1m No 70.00 Rs. -
48
Page 40 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
iv For depth above 2.1m and up to 2.4m No 77.00 Rs. -
v For depth above 2.4m and up to 2.7m No 113.00 Rs. -
vi For depth above 2.7m and up to 3.0m No 150.00 Rs. -
vii For depth above 3.0m and up to 3.6m No 90.00 Rs. -
vii For depth above 3.6m and up to 4.2m No 95.00 Rs. -
viii For depth above 4.2m and up to 4.8m No 60.00 Rs. -
Page 41 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
49
Providing sand cast iron drop connection externally for 60
cm drop from branch sewer line to main sewer manhole
including inspection and cleaning eye with chain and lid,
sand cast iron drop pipe and bend encased all-round with
cement concrete 1:5:10 (1 cement : 5 fine sand : 10
graded stone aggregate 40 mm nominal size) with all
centring and shuttering required, cutting holes in walls
and making good with brick work in cement mortar 1:4 (1
cement : 4 coarse sand) plastered with cement mortar 1:3
(1 cement : 3 coarse sand) on inside of the manhole wall
lead caulked joints between sand cast iron pipes and
ittings, stiff cement mortar 1:1 (1 cement : 1 fine sand)
joints between sand cast iron tee and S.W. pipe, making
required channels complete as per standard design and
specifications :
i 150 mm dia. sand cast iron drop connection each 10.00 Rs. -
50Extra for depths beyond 60 cm of sand cast iron drop
connection complete :
i For 150 mm dia. sand cast iron drop connection meter 22.00 Rs. -
Page 42 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
51
Providing and constructing brick masonry chamber for
underground C.I. inspection chamber and bends with well
burnt modular clay bricks crushing strength not less than
35kg/cm² in cement mortar 1:4 (1 cement : 4 coarse sand)
C.I. cover with frame (light duty) 455x610 mm internal
dimensions, total weight of cover with frame to be not
less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2
coarse sand : 4 graded stone aggregate 20 mm nominal
size) foundation concrete 1:5:10 (1 cement : 5 fine sand :
10 graded stone aggregate 40 mm nominal size), inside
plastering 12 mm thick with cement mortar 1:3 (1 cement
: 3 coarse sand) finished smooth with a floating coat of
neat cement on walls and bed concrete etc. complete as
per standard design :
iInside dimensions 600x850 mm and 45 cm deep for pipe
line with three or more inlets Each 363.00 Rs. -
52
Brick work with modular fly-ash lime bricks (FaLG Bricks)
confirming to IS:12894-2002 of class designation 4.0 in
foundation and plinth in:
i Cement Mortar 1:6 (1 cement : 6 coarse sand) cum 230.96 Rs. -
53
Providing and making 15mm thick cement plaster on the
rough side of single or half brick wall of mix: all complete
as per technical Specifications and as per direction of
Engineer.
i In Cement Mortar 1:4 (1 cement : 4 fine sand) Sqm 71.80 Rs. -
Page 43 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii In Cement Mortar 1:6 (1 cement : 6 fine sand) Sqm 1,035.00 Rs. -
54
Providing orange colour safety foot rest of minimum 6
mm thick plastic encapsulated as per IS : 10910 on 12mm
dia steel bar conforming to IS : 1786 having minimum
cross section as 23 mmx25mm and over all minimum
length 263 mm and width as 165mm with minimum 112
mm space between protruded legs having 2 mm tread on
top surface by ribbing or chequering besides necessary
and adequate anchoring projections on tail length on 138
mm as per standard drawing and suitable to with stand
the bend test and chemical resistance test as per
specifications and having manufacture's permanent
identification mark to be visible even after fixing,
including fixing in manholes with 30x20x15 cm cement
concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) complete as per
design.
Each 8.00 Rs. -
55
Providing and fixing in position precast circular 560mm
internal dia SFRC/R.C.C. manhole cover or cover and
frame of approved quality:
i Cover and frame H D - 20 Each 2.00 Rs. -
56
Providing and fixing on wall face or under floor UV
stabilized Unplasticised Rigid PVC pipes (single socketed)
having 3.2mm wall thickness conforming to IS : 13592
(4kg/sqcm) including required couplers, jointing with seal
ring conforming to IS : 5382 leaving 10 mm gap for
thermal expansion etc complete.
Page 44 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
i 75 mm dia pipe. metre 6.00 Rs. -
57
Providing and fixing on wall face UV stabilized
Unplasticised - PVC moulded fittings/ accessories having
3.2mm wall thickness for Rigid PVC pipes conforming to IS
: 13592 (heavy) jointing with seal ring conforming to IS :
5382 leaving 10 mm gap for thermal expansion.
a Vent covel
i 75 mm Each 2.00 Rs. -
58
Providing and constructing soak pit 1.20x1.20x1.20m
filled with brickbats including S.W. drain pipe 100 mm
diameter and 1.20 m long complete as per standard
design.
Each 6.00 Rs. -
59
Supplying and laying following size RCC Hume pipe class
NP-2 (in standard length of 2 metre) with collar in ground
below road, path etc at a depth not less than 50 cm and
upto 90cm including excavation, dismantling of road if
required and refilling the trench with excavated material,
ramming and making the surface good etc. as required.
i 300 mm dia. R.C.C. pipe Rmt 140.00 Rs. -
Page 45 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
ii 200 mm dia. R.C.C. pipe Rmt 3,606.00 Rs. -
iii 150 mm dia. R.C.C. pipe Rmt 1,896.00 Rs. -
iv 100mm dia. R.C.C. pipe Rmt 855.00 Rs. -
60
Providing, Laying and jointing non-pressure (NP3) RCC
socket & spigot pipes with rubber gasket joint including
testing of joints. [Conforming to IS ; 458-1988, ISI marked
laying as per IS 783:1985)
i 450 mm dia Meter 6,720.00 Rs. -
ii 600 mm dia Meter 8,132.00 Rs. -
iii 900 mm dia Meter 1,850.00 Rs. -
iv 1000 mm dia. Meter 703.00 Rs. -
Page 46 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
61
Providing and laying Reinforced Cement Concrete pipe NP
3 /prestressed concrete pipe on first class bedding.
(Laying Reinforced cement concrete pipe NP3
/prestressed concrete pipe for culverts on first class
bedding of granular material including fixing collar with
cement mortar 1:2 but excluding bedding below
pipes,excavation, protection works, backfilling, concrete
and masonry works in head walls and parapets . ) all
complete as per technical Specifications and as per
direction of Engineer.
i 450 mm dia Rmt 948.00 Rs. -
ii 600 mm dia Rmt 30.00 Rs. -
iii 1000 mm dia Rmt 507.00 Rs. -
62
Providing and fixing cast iron grating for gully trap. all
complete as per technical Specifications and as per
direction of Engineer.
i 3000x150mm square Each 966.00 Rs. -
Page 47 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
63
Supplying and laying ISI marked double wall HDPE pipe (IS
14930 Part II) having corrugation on the outer wall and
plan surface on inner wall in ground below road, path etc
at a depth not less than 40 cm and upto 90 cm including
excavation, dismantling of road if required and refilling
the trench with excavated material, ramming and making
the surface good etc. as required. all complete as per
technical Specifications and as per direction of Engineer.
i 200 mm outer dia Meter 84,195.00 Rs. -
ii 120 mm outer dia Meter 1,04,910.00 Rs. -
64
Providing and fixing un-polished 45mm to 50mm thick
RAJIM SAND STONE laid on drainage wall top for the base
of drain slab, as per drawing and as per direction of
Engineer complete etc.
sqm. 11,785.00 Rs. -
65
Providing and laying Pitching on slopes laid over prepared
filter media including boulder apron laid dry in front of
toe of embankment complete as per drawing and
Technical specifications as per section 2504
i Stone/Boulder Cum 814.80 Rs. -
Page 48 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
66
Excavation for Structures (Earth work in excavation of
foundation of structures as per drawing and technical
specification, including setting out, construction of
shoring and bracing, removal of stumps and other
deleterious matter, dressing of sides and bottom and
backfilling with approved material.) all complete as per
technical Specifications and as per direction of Engineer.
a Ordinary Soil
i Upto 3 m depth cum 2,855.90 Rs. -
ii 3 m to 6 m depth cum 1,010.72 Rs. -
67
Back filling behind abutment, wing wall and return wall
complete as per drawing and Technical specification
710.1.4 of I.R.C. 78 and 2200. all complete as per
technical Specifications and as per direction of Engineer.
i Granular material cum 2,255.53 Rs. -
Page 49 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
68
Providing and laying of Filter media with granular
materials/stone crushed aggregates satisfying the
requirements laid down in clause 2504.2.2. of MoRTH
specifications to a thickness of not less than 600 mm with
smaller size towards the soil and bigger size towards the
wall and provided over the entire surface behind
abutment, wing wall and return wall to the full height
compacted to a firm condition complete as per drawing
and technical specifications 710.1.4 of I.R.C. 78 and 2200
cum 154.70 Rs. -
69
Providing and laying Plain/Reinforced cement concrete in
sub-structure complete as per drawing and technical
specifications section 1500, 1700 and 2200 all complete
as per technical Specifications and as per direction of
Engineer.
a Height upto 5m
i Using concrete Mixer
ii P.C.C. Grade M-15 cum 68.36 Rs. -
70
Providing and laying Plain/Reinforced cement concrete in
sub-structure complete as per drawing and technical
specifications section 1500, 1700 and 2200
a Height upto 5m
i Using concrete Mixer (R.C.C. Grade M-30) cum 860.70 Rs. -
71
Furnishing and Placing Reinforced/Prestressed cement
concrete in super-structure as per drawing and Technical
Specification sections 1500, 1600 and 1700 all complete
as per technical Specifications and as per direction of
Engineer.a RCC Grade M 30
For Solid Slab Super Structure
Page 50 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
Using Concrete Mixer
i Height upto 5m cum 215.48 Rs. -
72
Providing and laying M-30 grade Reinforced cement
concrete approach slab including reinforcement and
formwork complete as per drawing and Technical
specification and as per relevant sections 1500, 1600,
1700 and 2704 all complete as per technical
Specifications and as per direction of Engineer.
cum 69.15 Rs. -
73
PCC M15 Grade leveling course below approach slab
complete as per drawing and Technical specification and
as per relevant section 2700 all complete as per technical
Specifications and as per direction of Engineer.
cum 23.21 Rs. -
74
Construction of precast RCC railing of M30 Grade,
aggregate size not exceeding 12 mm, true to line and
grade, tolerance of vertical RCC post not to exceed 1 in
500, centre to centre spacing between vertical post not
to exceed 2000 mm, leaving adequate space between
vertical post for expansion, complete as per approved
drawings and technical specifications as per relevant
clauses of section 1500, 1600, 1700 and 2703 (vide
drawing No. SD/202, SD/304) all complete as per
technical Specifications and as per direction of Engineer.
meter 51.00 Rs. -
75
Supplying, fitting and placing un-coated HYSD bar
reinforcement in foundation complete as per drawing and
technical specifications as per section 1600.
MT 34.04 Rs. -
Page 51 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
76
Supplying, fitting and placing HYSD bar reinforcement in
sub-structure complete as per drawing and technical
specifications section 1600 and 2200
MT 95.06 Rs. -
77
Supplying, fitting and placing HYSD bar reinforcement in
super-structure complete as per drawing and technical
specifications
MT 32.32 Rs. -
78Providing and fixing in position tar paper bearing for slab
as per approved drawings and specificationsqm 750.98 Rs. -
79 Filler joint
i
Providing & fixing 2 mm thick corrugated copper plate (
12 m long x 25 cm wide ) in expansion joint complete as
per drawing & Technical Specification.
sqm 4.42 Rs. -
ii
Providing & fixing 20 mm thick compressible fiber board (
12 m long x 25 cm deep ) in expansion joint complete as
per drawing & Technical Specification.
sqm 8.84 Rs. -
iii
Providing and fixing in position 20 mm thick premoulded
joint filler ( 12 m long x 30 cm deep ) in expansion joint
for fixed ends of simply supported spans not exceeding 10
m to cater for a horizontal movement upto 20 mm,
covered with sealant complete as per drawing and
technical specifications.
sqm 13.26 Rs. -
iv
Providing and filling joint sealing compound ( 12 m long x
100 mm wide x 10 mm deep recess) as per drawings and
technical specifications with coarse sand and 6% bitumen
by weight
sqm 13.26 Rs. -
Page 52 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
80Drainage Spouts complete as per drawing and Technical
specifications of section 2705each 20.40 Rs. -
81
Providing plain cement concrete M 15 in footpaths
including centring and shuttering all complete as per
drawing and Technical Specification Section 1500 & 1700.
cum 35.36 Rs. -
82
Providing and laying Filter material underneath pitching
in slopes complete as per drawing and Technical
specification including trimming of slopes to proper
profile and preparation of bed as per section 2504
cum 30.60 Rs. -
83
Providing weep holes in Brick masonry/ Plain/ Reinforced
concrete abutment, wing wall/return wall with 100 mm
dia AC pipe, extending through the full width of the
structure with slope of 1V :20H towards drawing foce.
Complete as per drawing and Technical specifications
section 2706 and 2200
meter 22.10 Rs. -
84
Providing and laying Cement concrete wearing coat M-
30 grade including reinforcement complete as per
drawing and Technical Specifications
cum 126.48 Rs. -
85
Cast in Situ Cement Concrete M20 kerb (Construction of
cement concrete kerb with top and bottom width 115 and
165 mm respectively, 250 mm high in M 20 grade PCC on
M-10 grade foundation 150 mm thick, foundation having
50 mm projection beyond kerb stone, kerb stone laid with
kerb laying machine, foundation concrete laid manually,
all complete as per clause 408)
meter 51.00 Rs. -
Page 53 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
86
Providing & filling 37/40 mm. wide expansion joint
between spans in wearing coat with premoulded joint
filler, primer coat and joint sealing compound as per
MOST standard drawing and specifications as per section
2600 in:-
i R.C.C. 75 mm deep wearing coat metre 25.50 Rs. -
87
Painting on kerbs in black and yellow alternate bands
including cost of material and labour complete as per
drawings and specifications as per clause 803.
i With Road Marking Paint metre 51.00 Rs. -
88
Surface dressing of the ground including removing
vegetation and making up undulations and in-equalities
not exceeding 15 cms in depth/ height including disposal
of rubbish upto 1.5 m lift and lead upto 50m (at least 5m
away from the dressed area).
Sqm 56,445.00 Rs. -
89
Footpaths and Separators (Construction of
footpath/separator by providing a 150 mm compacted
granular sub base as per clause 401 and 75 mm thick
cement concrete base with PCC grade M-15, over laid
with precast cement concrete tiles 25mm thick fixed in
20mm thick cement mortar 1:3 including provision of all
drainage arrangements but excluding kerb channel
excluding cost of GSB.) as per clause 410.
Sqm 2,480.00 Rs. -
Page 54 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
90
Providing and fixing kerb stones 100 mm thick and 600
mm wide chisel dressed cut stones fixed in CC 1:3:6 (block
size 250 x 225 mm) including all excavation. all complete
as per technical Specifications and as per direction of
Engineer.
metre 2,480.00 Rs. -
91
Random rubble masonry with hard stone in foundation
and plinth in Cement Mortar 1:6 (1 Cement : 6 Coarse
Sand) including leveling up with cement concrete 1:6:12
(1 cement : 6 coarse sand: 12 stone aggregate 20mm
nominal size) upto plinth level.
Cum 739.71 Rs. -
92
Random rubble masonry with hard stone in foundation
and plinth in Cement Mortar 1:6 (1 Cement : 6 Coarse
Sand) including leveling up with cement concrete 1:6:12
(1 cement : 6 coarse sand: 12 stone aggregate 20mm
nominal size) upto plinth level.
i
Extra for random rubble masonry with hard stone in
superstructure above plinth level for every floor or part
thereof in addition to rate for foundation and plinth:
Cum 555.05 Rs. -
Page 55 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
93
Pointing on stone work with cement Mortar 1:3 (1
cement : 3 fine sand) all complete as per technical
Specifications and as per direction of Engineer.
i Ruled pointing Sqm 2,200.80 Rs. -
94
Steel work welded in built up sections/ framed work
including cutting,hoisting, fixing in position and applying a
priming coat of red oxide zinc chromate primer. all
complete as per technical Specifications and as per
direction of Engineer.
iIn gratings, frames, guard bar, ladder, railings, brackets,
gates and similar works.Kg 831.60 Rs. -
95
MS Grill: Providing and fixing M.S. grill of approved
pattern made of M.S. flats or square or round bars
welded to steel frame of windows etc. including applying
a priming coat welded to frame with all necessary fitting
complete including applying a priming of red oxide zinc
chromate primer. all complete as per technical
Specifications and as per direction of Engineer.
Kg 10,146.00 Rs. -
96
15 mm thick Table rubbed polished Granite stone slab
flooring laid over 20mm (Average) thick base of cement
mortar 1:4 (1 cement : 4 coarse sand) laid and jointed
with grey cement slurry including rubbing and polishing
etc. complete. (Area of slab should be 0.50 sqm and
above)
`
i Granite stone grey/pink sqm 44.40 Rs. -
Page 56 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
97Painting on new work (two or more coats) to give an even
shade with:
iSatin synthetic enamel paint (top most approved branded
quality) sqm 3,134.88 Rs. -
98
Providing and fixing G.I. chain link fabric fencing of
required width in mesh size 50x50 mm including
strengthening with 2 mm dia wire or nuts, bolts and
washers as required complete as per the direction of
Engineer-in-charge.
i Made of G.I. wire of dia 4 mm Sqm 3,116.40 Rs. -
Page 57 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
99
Planting Permanent Hedges including Digging of Trenches
(Planting permanent hedges including digging of trenches,
60 cm wide and 45 cm deep, refilling the excavated earth
mixed with farmyard manure, supplied at the rate of 4.65
cum per 100 meters and supplying and planting hedge
plants at 30 cm apart), including maintenance of one
year. all complete as per technical Specifications and as
per direction of Engineer.
No. 858.00 Rs. -
100
Planting of Trees and their Maintenance for one Year. all
complete as per technical Specifications and as per
direction of Engineer.
(Planting of trees by the road side (Avenue trees) in 0.60
m dia. holes, 1 m. deep dug in the ground, mixing the soil
with decayed farm yard/sludge manure, planting the
saplings, backfilling the trench, watering, fixing the tree
guard and maintaining the plants for one year) all
complete as per technical Specifications and as per
direction of Engineer.
Nos 1,006.00 Rs. -
101
Tree Guard with MS Angle Iron and Steel Wire (Providing
and fixing tree guard 0.60 meter square, 2.00 meter high
fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25
x 3 mm at 100mm centre to centre and steel wire 3 mm
dia. welded and fabricated as per design in two halves
bolted together, fixed in ground with P.C.C M-10 of
dimensions 150x150x200mm.)
Each 399.00 Rs. -
Page 58 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
102
Providing and planting following herbs in garden including
preparation of soil, earth mixed with manure or sludge in
the ratio of 2:1 by volume (2 parts of stacked volume of
earth after reduction by 20% :1 part of stacked volume of
manure after reduction by 8%) watering, dressing
including removal of rubbish and surplus earth,
preparation of base plantation, providing and spreading
different fertilizers, soil and sand if any with all leads and
lifts including cost of manure, sludge or extra good earth
if needed and deweeding and as per instruction of
Engineer in charge
Page 59 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
i Dhoob grass Sqm 16,996.90 Rs. -
ii Carpet grass Sqm 7,891.90 Rs. -
103
Supplying, Installation, Testing and Commissioning of
"Circular Swing" play equipment : The leg support , top
bar and swing frame is made from powder coated ‘A’
class GI pipes. two seats are made out of molded plastic
including all material, labour, accessories and
commissioning all complete as per the direction of
engineers in charge and Technical Specification.
No. 3.00 Rs. -
104
Supplying, Installation, Testing and Commissioning of
"Toddler Swing" play equipment : The toddler swing the
center support is made up of GI pipes. Between the two
horizontal bars there is a heavy-duty metal clamp
attached to it including all material, labour, accessories
and commissioning all complete as per the direction of
engineers in charge and Technical Specification.
No. 6.00 Rs. -
105
Supplying, Installation, Testing and Commissioning of
"MultiSeater See-Saw" play equipment : The MS See saw
comprises four FRP seats. The lever is consisted of
powder coated GI pipes and bearing is heavy duty nylon
bush type including all material, labour, accessories and
commissioning all complete as per the direction of
engineers in charge and Technical Specification.
No. 6.00 Rs. -
Page 60 of 109
Sr.
NoDescription of Item Unit Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
106
Supplying, Installation, Testing and Commissioning of
"Standered See-Saw" play equipment : The standard see
saw is a good entertainer for the children. The lever of the
see – from moulded plastic including all material, labour,
accessories and commissioning all complete as per the
direction of engineers in charge and Technical
Specification.
No. 6.00 Rs. -
107
P/ Instalation of Dust Bin. Height = 0.6m. Dia. = 0.3m.
Dustbin is especially designed for accommodating well as
wet kind of trash. cylinder of the bin is fabricated out of
Aluminium perforated sheet 300mm in diameter and
380mm long with a self-closing tilt able lid. The drum is
mounted on nylon bearings to provide it with complete
rotation of the drum to facilitate the garbage removal.
The frame of dustbin is made up of 25NB powder coated
GI pipes including all material, labour, accessories and
commissioning all complete as per the direction of
engineers in charge .
No. 37.00 Rs. -
Rs. - Sub Total of Utility Services
Page 61 of 109
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
C
I
1 33 KV RMU
a
Supplying, Receiving, Storage, Installation, Testing and
Commissioning of approved make Motorized type Ring Main
Unit (extendible type) for out door installation, rated for 36KV,
50Hz, 630A, STR of 25kA for 1sec with SF6 insulation having 2
sets of three positon Load break Switch with earthing switch as
Incomer and 1 set of three position Load break Switch with
earthing switch for Tee-off. The units shall be complete with
interconnections of both Power & Control, accessories, hardwares
etc as required for completeness and as per direction of engineer,
attached specification, CSPDCL standards and Elecrical
Inspectorate Standards.
The accessories shall include:
3 Set of ON/ OFF and Phase indicating lamps
3 Nos end termination kit for 3 core XLPE cable
Set 2.0 Rs. -
2
Supplying and laying following sizes one number XLPE, steel
armoured, aluminium conductor power cable of 33 KV grade in
existing RCC/ HUME/ STONEWARE/ METAL/HDPE pipe as
required..
a 3Cx400 sqmm mtr 100.0 Rs. -
Bill of Quantity
Integrated Infrastructure Development Works for Phase-I works at sector-12, 40 and other Specified areas at Naya Raipur
33 KV Power supply to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur
ELECTRICAL WORKS
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
b 3C X 300 sqmm mtr 6500.0 Rs. -
c 3C X 120 sqmm mtr 100.0 Rs. -
3
Supplying and making indoor cable end termination with heat
shrinkable jointing kit complete with all accessories including
lugs suitable for following size of 3 core, XLPE aluminum
conductor cable of 33 KV grade as required :
a 400 sqm Each 1.0 Rs. -
b 300 sqmm Each 4.0 Rs. -
c 120 sqmm Each 1.0 Rs. -
4
Supplying and making outdoor cable end termination with heat
shrinkable jointing kit complete with all accessories including
lugs suitable for following size of 3 core, XLPE aluminum
conductor cable of 33 KV grade as required :
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
a 300 sqmm Each 2.0 Rs. -
b 120 sqmm Each 2.0 Rs. -
5
Supplying and making straight through cable jointing with heat
shrinkable jointing kit complete with all accessories including
ferrules suitable for following size of 3 core, XLPE aluminum
conductor cable of 33 KV grade as required :
a 300 sqmm Each 13.0 Rs. -
b 120 sqmm Each 1.0 Rs. -
6
Supplying and laying of 50mm x 6mm GI earth strip along with
the 33kV cable and making connection with steel supports enroute
and connecting firmly with the earthing systems of end stations
complete with ferrules, other accessories, hardwares etc as
required for completeness and as per direction of engineer,
attached specification, CSPDCL standards and Elecrical
Inspectorate Standards.
mtr 500.0 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
7
Providing and fixing HT Danger Notice Plate of 250 mm x 200
mm 2mm thick, made of mild steel and vitreous enamelled white
on both sides and inscription in signal red colour on front side as
per IS:2551 with accessories, hardwares etc as per direction of
engineer, CSPDCL standards and Electrical inspectorate
standards.
Each 2.0 Rs. -
8
Construction of plinth for , RMU in RM-15 RCC construction for
installation of RMU including excavation, laying of PCC, neatly
dressed, plastered, supply of all materials as required for
completeness, as per attached specification/ drawing, CSPDCL
standards and direction of EIC.
cum 65.0 Rs. -
9
Supply, Installation, Testing & Commissioning of indoor, floor
mounted 33 KV switchboard comprising of the 2 number vertical
panels with draw type VCB rating 1600 A , 36 KV, 25 kA shall
be act as outgoing panel with CT ratio of 400/200/5 amp and will
be connected with existing panel in substation. The panel shall
have Static Energy Meters, O/C and E/F relay, auxiliary relays
etc.The panel shall confirm 61850 protocol & as per CSPDCL
standards and direction of EIC.
Set 1.0 Rs. -
II
10 11 KV RMU
(a)
Supply, Installation, Testing & Commissioning of floor mounted
SF6, motorized type RMU (extendible type) comprising of 2 nos.
12 kV, 630 A LBS for loop in and loop out to form ring main
system and 1 no VCB unit shall controlled distribution transformer
complete with accessories, hard wares etc. as required for
completeness as per attached specification/ drawing, CSPDCL
standards and direction of EIC.
Set 2.0 Rs. -
11KV System to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
(b)
Supply, Installation, Testing & Commissioning of floor mounted
SF6, motorized type RMU (extendible type) comprising of 3 nos.
12 kV, 630 A LBS for loop in and loop out to form ring main
system and 1 no VCB unit shall controlled distribution transformer
complete with accessories, hard wares etc. as required for
completeness as per attached specification/ drawing, CSPDCL
standards and direction of EIC.
Set 3.0 Rs. -
(c)
Supply, Installation, Testing & Commissioning
of floor mounted Oil type RMU (extendible type) comprising of 2
nos. 12 kV, 630 A LBS for loop in and 1 no fuse unit shall
controlled distribution transformer complete with accessories, hard
wares etc. as required for completeness as per attached
specification/ drawing, CSPDCL standards and direction of EIC.
Set 3.0 Rs. -
11
Supplying and laying following sizes one number XLPE, steel
armoured, aluminium conductor power cable of 11 KV grade in
existing RCC/ HUME/ STONEWARE/ METAL/HDPE pipe as
required..
a 3Cx240 sqmm mtr 9415.0 Rs. -
c 3C X 120 sqmm mtr 400.0 Rs. -
d 3Cx 95 sqmm mtr 1600.0 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
e 3C X 70 sqmm mtr 1600.0 Rs. -
12
Supplying and making outdoor cable end termination with heat
shrinkable jointing kit complete with all accessories including
lugs suitable for following size of 3 core, XLPE aluminum
conductor cable of 11 KV grade as required :
a 240 sqmm Each 6.0 Rs. -
b 120 sqmm Each 2.0 Rs. -
c 95 sqmm Each 2.0 Rs. -
d 70 sqmm Each 2.0 Rs. -
13
Supplying and making indoor cable end termination with heat
shrinkable jointing kit complete with all accessories including
lugs suitable for following size of 3 core, XLPE aluminum
conductor cable of 11 KV grade as required :
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
a 240 sqmm Each 12.0 Rs. -
b 120 sqmm Each 2.0 Rs. -
c 95 sqmm Each 3.0 Rs. -
d 70 sqmm Each 3.0 Rs. -
14
Supplying and making straight through cable jointing with Heat
Shrinkable Jointing Kit complete with all acessories including
ferrule suitable for following size of 3 core, XLPE aluminum
conductor cable of 11 KV grade as required :
a 240 sqmm Each 24.0 Rs. -
b 95 sqmm Each 3.0 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
c 70 sqmm Each 3.0 Rs. -
15
Supply and fixing of 11 kV Danger plates as per specification of
Discom on the existing poles complete in all respect as per
Discom specification.
Each 18.0 Rs. -
16
Supply, Installation, Testing & Commissioning of indoor, floor
mounted 11KV switchboard comprising of the 3 number vertical
panels with draw out type VCB rating 800 A 12KV, 18.4kA
shall be act as out going panel with CT ratio of 200/100/5 amp and
will be connected with existing panel in substation . The panels
shall have Static Energy meter, O/C and E/F relay etc. The
panel shall confirm 61850 protocol & as per CSPDCL standards
and direction of EIC.
Set 2.0 Rs. -
17
Supply, Installation, Testing & Commissioning of floor mounted
Outdoor type package substation with facility for internal lighting,
earthing, padlocks etc.Connection between RMU & transformer
will be by Aluminium bus bar and connections from transformer to
LT ACB. Package Substations will have following equipment.
1. HT side Non extensible 12 kv 630 RMU having SF6/Air
insulation with 2 nos. LBS and 1 nos VCB for transformer
protection having fault rating of 25KA for 1 Sec.
2. 11/.433 Kv 500 KVA Oil type Transformer having doubled
wound copper winding with A Class insulation.
3. LT Side having 800 amp ACB with O/C,E/F protection and
having 4 nos 250 amp MCCB for outgoing. The equipment shall
be SCADA compatible having communication port and having
provision of DT Metering within it, completeness as per attached
specification/ drawing, CSPDCL standards and direction of EIC.
nos 5.0 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
III
18
Designing and providing suitable RCC foundation for 7 metre to 12
metre high GI octagonal pole including steel reinforcement
(minimum 90kg per cum), form work, embeding 2 nos 50mm dia
PVC pipe for cable entry in each foundation, excavation disposal
of surplus soil and curing etc. as required.
Cum 705.00 Rs. -
19
Supply of hot dipped galvanized (in single dip to average 65
micron) octoganal pole made of 3mm thick steel sheet having
window and flush cover with locking arrangement at suitable
height from base for cable termination block, pole suitably
reinforced with welded steel section at window cut section tomake
the strength of pole unaffected, with following minimum
specifications including 3mm thick anchor plate, 4 nos 20mm dia
foundation bolts of EN8 grade. (designed for wind speed upto
180km/hr)
a7 metre high, dia 130mm at bottom and 70mm at top, base
plate size 220x220x12mm, foundation bolts 700mm longEach 518.00 Rs. -
b6 metre high, dia 130mm at bottom and 70mm at top, base
plate size 220x220x12mm, foundation bolts 600mm longEach 285.00 Rs. -
20
Supply of hot dipped galvanized (in single dip to average 70
micron) octoganal pole made of 4mm thick steel plate having base
plate 275x275x16mm, window and flush cover with locking
arrangement at suitable height from base for cable termination
block, pole suitably reinforced with welded steel section at window
cut section to make the strength of pole unaffected, including
template and anchor plate 270x270x3mm with 4 nos 750mm long,
24mm dia foundation bolts (EN8 grade).(designed for wind speed
upto 180km/hr)
Street Lightning to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
a 9 metre high, minimum dia 155 mm at bottom and 70 mm at top Each 440.00 Rs. -
4
Erection of GI octogonal pole on existing cement concrete
foundation having grouted bolts and nuts, aligning in true vertical
position as required.
a 6 meter high Each 285.00 Rs. -
b 7 meter high Each 518.00 Rs. -
c 9 metre high Each 440.00 Rs. -
21
Supply and fixing following street light pole bracket on existing
pole made out of 50 mm dia MS "B" class pipe welded to 300 mm
long MS pole canopy of suitable dia at a angle of 102.50 including
having MS triangular stiffner of size 150 X 50 X 5 mm thick,
making arrangement for tightening the bracket with pole by
providing suitable size heavy duty nuts and bolts in canopy,
painting with one coat of approved steel primer etc. as required.
a Single Over Hang 1.00 metre Long Each 285.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
b Single Over Hang 1.50 metre Long Each 690.00 Rs. -
c Double Over Hang 1.50 metre Long Each 226.00 Rs. -
d Double Over Hang 1.00 metre Long Each 40.00 Rs. -
22
Supplying, installation, testing and commissioning of following
230/250 volts LED street light fitting with all accessories like
driver, heat sink made of die cast aluminium with IP 66 protection
and 5 KV surge protection on pole bracket complete as required.
a Not More than 40 Watt Each 285.00 Rs. -
b Not More than 65 Watt Each 626.00 Rs. -
c Not More than 90 Watt Each 288.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
d Not More than 120 Watt Each 320.00 Rs. -
Design, Fabrication, Supply, Erection, Testing and commisioning
of Powder coated, Weather Proof Double door type Feeder pillar
fabricated out of 14 guage CRCA sheet steel in cubical, free
standing, dust and vermin proof, with reinforcement of suitable
size angle iron, channel, T -iron or flats as required. Feeder pillar
shall be treated with all anti-corrosive process before painting as
per specification. Feeder Pillar shall be suitable for 415V, 3-Phase,
Four wire, 50 Hz supply complete with earth bus and lifting hooks
as required in case of large panels.Approval shall be taken for
each panel before fabrication. (All hardwares like nuts and bolts
used shall be Galvanized and Zinc passivated)
Rs. -
INCOMER
1No. 4 Pole 100A TPN MCCB (35 KA)
1No. 100A FP Contactor, AOM switch & Timers for 24 Hrs. setting
Metering & Indication
1 set of phase indicating lamps
BUS-BAR
1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC
SleevesOUTGOINGS
24 Nos. 32A SP MCB
GPRS MODULE FOR AUTOMATION
24
Earthing with G.I. earth pipe 3.0 mtr long, 40 mm dia including
accessories, and providing masonry enclosure with cover plate
having locking arrangement and watering pipe etc. with charcoal
and salt as required.
Set 1287.00 Rs. -
25
Supplying and laying double wall HDPE pipe having corrugation
on the outer wall and plan surface on inner wall in ground below
road, path etc at a depth not less than 40 cm including excavation,
dismantling of road if required and refilling the trench etc. as
required.
23 Set 14.00
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
a 40 mm mtr 40016.00 Rs. -
b 90 mm mtr 500.00 Rs. -
26
Supplying and laying following sizes one number PVC insulated,
PVC sheathed, steel armoured, aluminium conductor power
cable of 1.1 KV grade in existing RCC/HUME/STONE
WARE/METAL/HDPE pipe required.
a 2x6 sq.mm mtr 1000.00 Rs. -
b 4x10 sq.mm mtr 2000.00 Rs. -
c 4 x16 sq. mm. mtr 41500.00 Rs. -
d 3.5 x 25 sq. mm. mtr 2800.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
e 3.5 x 50 sq. mm. mtr 3700.00 Rs. -
f 3.5 x 70 sq. mm. mtr 4000.00 Rs. -
27
Supplying and making end termination with brass compression
gland and aluminum lugs for following size armoured aluminum
conductor power cable of 1.1 KV grade as required.
a 2x6 sq.mm Each 10.00 Rs. -
b 4x10 sq.mm Each 15.00 Rs. -
c 4 x 16 sq. mm. Each 300.00 Rs. -
d 3.5 x 25 sq. mm. Each 52.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
e 3.5 x 50 sq. mm. Each 30.00 Rs. -
f 3.5 x 70 sq. mm. Each 25.00 Rs. -
28
Supplying, fixing and cramping suitable size and all type
aluminium ferule/ lugs to following size 1.1 KV grade power
cable core/ lead, pressed with high pressure cramping tool
including connection to switch gear/ MCCB etc as required.
a 2X6 sq.mm Each 50.00 Rs. -
b 4X10 sq.mm Each 100.00 Rs. -
c 4 x 16 sq. mm. Each 12000.00 Rs. -
d 3.5 x 25 sq. mm. Each 280.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
e 3.5 x 50 sq. mm. Each 155.00 Rs. -
f 3.5 x 70 sq. mm. Each 50.00 Rs. -
29
Supply and drawing following sizes of FR PVC insulated copper
conductor, single core cable in the existing surface/ concealed,
steel/ PVC conduit as required.
a 3 x 1.5 sq.mm. (from Pole Junction box to Light fitting) mtr 14000.00 Rs. -
Rs. -
30
Supplying erection testing and commissioning of hot dipped
galvanised (single dip 86 micron) 20 metre High mast pole on
RCC foundation with all accessories and equipments,
detailed as below to withstand wind pressure upto 180km/hr
and minimum following specifications:
a) HM shaft made of not more than 2 sections of suitable
lengths with telescopic stressfit joints between sections without
any circumpherencial welding, sheet thickness 4mm top and
bottom sections, nominal dia 460mm on bottom and 150 mm on
top, base plate 30mm thick 670mm dia, PCD of foundation
bolts 650mm.
b) Double drum winch for lowering & raising of lantern carriage
on high mast with operatable with power tool/ manual handle
attachment with a torque limiting device for safe locking of
carriage.
c) Raising/lowering type lantern carriage designed to carry
specified nos of luminaries, control gear box, junction box.
d) Top pulley assemble with weather proof cover.
Each 12.00
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
31
Supplying, fixing, testing and commissioning of following 230/250
volts metal halide lamps on High mast pole
etc as required
Each 132.00 Rs. -
32
Supplying and making straight through joint with heat
shrinkable joint kit including aluminium ferrules for following
size of PVC insulated and PVC sheathed / XLPE aluminum
conductor cable of 1.1 KV grade as required.
Rs. -
a 3.5 x 70 sq. mm. Each 9.00 Rs. -
b 3.5x50 sq .mm Each 6.00 Rs. -
IV
33
Supply, Installation, Testing & Commissioning of floor mounted
SF6, motorized type RMU (extendible type) comprising of 3 nos.
12 kV, 630 A LBS for loop in and loop out to form ring main
system and 1 no VCB unit shall controlled distribution transformer
complete with accessories, hard wares etc. as required for
completeness as per attached specification/ drawing, CSPDCL
standards and direction of EIC.
No. 12.00 Rs. -
Power supply for Street light to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
34
Supply Installation, testing & commissioning of 11/ 0.433 KV,
315KVA distribution transformer with off load tap changer,
copper wound, oil cooled suitable for outdoor use with required
fittings, accessories,both side cable terminal box, hardwares etc.
as required for completeness as per attached
specification/drawing, CSPDCL standards and direction of EIC.
Nos 2.00 Rs. -
35
Supply Installation, testing & commissioning of 11/ 0.433 KV, 100
KVA distribution transformer with off load tap changer, AL wound,
oil cooled suitable for outdoor use with required fittings,
accessories,both side cable terminal box, hardwares etc. as
required for completeness as per attached specification/drawing,
CSPDCL standards and direction of EIC.
Nos 14.00 Rs. -
36
Supply Installation, testing & commissioning of outdoor, structure
mounted, LT DB rated for 415v, 450 A, 4 wires with copper bus
bars, 1no. 450 A, 25 kA, 4 P MCCB as incomer, 3nos. 125 A ,4 P
MCCB as outgoing feeder with supporting structure, accessories,
hardwares etc. as required for completeness as per attached
specification/ drawing, CSPDCL standards and direction of EIC.
Nos 12.00 Rs. -
37
Supplying and laying of following one number XLPE, steel
armoured, aluminium conductor power cable of 11 KV grade in
existing RCC/ HUME/ STONEWARE/ METAL/HDPE pipe as
required for completeness, as per attached specification/ drawing,
CSPDCL standards and direction of EIC
a 3x70 sqm Mtrs 9840.00 Rs. -
b 3x120 sq mm Mtrs 2000.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
Rs. -
38
Supplying and making INDOOR cable end jointing with heat
shrinkable cable jointing kit including lugs and other jointing
materials, for following size of 3 core, XLPE aluminum
conductor cable of 11 KV grade as required for completeness as
per attached specification/ drawing, CSPDCL standards and
direction of EIC.
a 3x70 sqm Nos. 30.00 Rs. -
b 3x120 sq mm Nos. 2.00 Rs. -
39
Supplying and making STRAIGHT THROUGH cable jointing
with heat shrinkable cable jointing kit including ferrule and other
jointing materials, for following size of 3 core, XLPE aluminum
conductor cable of 11 KV grade as required
nos
a 3x70 sqm 17.00 Rs. -
b 3x120 sq mm 3.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
40
Supply of all materials, installation, testing and commissioning of
GI pipe electrode as per IS: 3043 comprising of 40mm dia,
2.9mm thick, 3m long class A GI pipe with flange, 16nos. 12mm
dia through holes buried in a pit. The scope shall cover excavation
in all kinds of soil and rock, filling the pit with equal proportion of
salt and charcoal in layers of 300mm depth, 150mm wide alround
the pipe from bottom upto a depth of 300mm below the masonary
chamber, refilling by excavated soil free from rock and shark
edges; provision of watering arrangement with GI funnel and wire
mesh be enclosed in a brick masonary chamber of 400mm x
400mm x 400mm with removable RCC cover on top. The
connection from the flanges of the pipe shall be established by
50mm x 6mm GI strip using 12mm dia GI hardwares. The work
shall be carried out with accessories, hardware etc as required for
completeness and as per attached specification/drawing, CSPDCL
standards and direction of EIC.
Nos. 30.00 Rs. -
41
Supply, running and terminating of GI materials as earth
continuity conductor to earth all the metallic parts/ neutral of
transformer/ lightning arrestors, control room equipments to earth
electrodes with accessories, hardwares etc. as required for
completeness, as per attached specification/ drawings, CSPDCL
standards and direction of EIC.
a 50mm x 6mm strips mtrs 160.00 Rs. -
b 8 SWG wires mtrs 150.00 Rs. -
c 0 SWG wires mtrs 120.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
42
Supplying and erecting MS gate of approx. size 3.0 m (W) x
2.0 m (H) in two laps for electric sub-station switch yard
fencing frame made of angle iron size 50 X 50 X 6 mm on top
bottom and sides fitted with flat iron support of size 25 X 6 mm
on mid way horizontaly and square bar of size 8 mm at every
100mm vertically including 3 sets of heavy duty MS hinges
and aldrop complete duly painted with one coats of red oxide
and two coats of approved colour paint.
Sqm 60.00 Rs. -
43
Supplying and erecting chain link mesh fencing for electric
sub-station switch yard of 2.5 m approx. height from ground
level using angle iron size 50 X 50 X 6 mm erected in C.C.
foundation 15 X 15 X 40 cm deep at every 2 metre fitted with
flat iron support of size 25 X 6 mm on top, bottom and mid
way and chain link mesh 50 x 50 mm aparture and 4 mm dia
G.I. hard wire securing and screwing with 2mm dia G.I. wire,
G.I. staples, G.I.U-nails or steel pins to the angle iron at every
distance of 30 cms, by iron studs complete duly painted with
one coats of red oxide and two coats of approved colour paint.
sqm 348.00 Rs. -
44
Horizontal drilling: Horizontal directional drilling along roads for
laying XLPE HT/ LT, UG cable, for communication cable along
with suitable HDPE Duct at various locations as pointed out by
departmental officers, includes Survey of site information
collection regarding underground utilities, sensing of utilities by
sensing equipment, pit making, pilot drilling, pre-reaming pulling
HDPE duct of suitable size in single roll, pulling HT/ LT UG cable
through installed HDPE duct, providing barricades and necessary
signal lights, closing of pits with excavated earth including cost of
HDPE pipe, consolidating pit are, including road
restoration/supervision departments, cost of all materials, labour,
conveyance, hire charges etc. complete preparation of pit by
excavated soil/ hard morum & refilling compacting surface as it is
position / horizontal drilling across road for cable laying propose
with disturbing present installation as per instruction, Guide line
Detail technical specifications as per direction of Engineer in
charge
rmt 1150.00 Rs. -
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
V
45
Townguide Post top luminaire - Integral LED post top luminaire
with two layer optics, IP 66, IK10, and effective system lumen
output of more than 3000 lumens. The Fixture has clear bowl with
CRI greater than 80 & CCT Natural day light & warm light. Housing
is high pressure die cast aluminium with PU paint for higher
reliability. L70 life of the LED is more than 50000 burning hours.
The fixture is provided with 3 m height mild steel & hot dip
galvanised pole primered and painted with polyurethane. The pole
has a flush door at teh bottom with provision for loop in & loop out.
nos 12.00 Rs. -
46
BBG 151, LED marker light for directional guidance made from
high pressure die cast aluminium housing and IP 67, IK10, with
toughened glass diffuser. The product should e not more than 3 W
with lumens output of more than 35 lumens. It should be CCE, CE
& RohS compliant in 3000 K. The outer casing should be in
stainless steel. L70 life of the fixture should be more than 25000
burning hours.
nos 16.00 Rs. -
47
BWG 150, Integral recessed LED wall light luminaire with high
pressure die cast aluminium body & polycarbonate diffuser. The
fixture is IP67 & IK10. The system wattage is 4 W and lumen
output is more than 35 lumens. The fixture is CCE, CE & RoHS
compliant. Size for the same should be 145 mm X 145 mm X 105
mm
nos 12.00 Rs. -
48
Color Burst PC,Integral Die cast aluminium body with powder
coated finish, 30 W RGB LED floodlight. The fixture is IP66, Class
2 Led product, UL, cUL, CE & PSE compliant. It should be
compatible with full range of Philips controllers Including LSM or I -
player. It should have clear tempered lens with 10 degree beam
abgle. The L70 life of the fixture with 3 RGB channels on should
be more than 55000 burning hours.
nos 18.00 Rs. -
Green Area Lighting to Phase-I works at sector-12, sector-40 and other Specified areas at Naya Raipur
Sr. No Description of Item Unit
Quantity Rate in INR Rate in Words ( Indian Rupee) Amount in INR
49
Data enabler Pro - Power / Data supplies DMX Ethernet - Integral
power / data enabler housed in IP66 high pressure die cast
aluminium housing , IP66, with maximum load capacity of 16
amps.
nos 20.00 Rs. -
50
Iplayer 3 - Compact DMX control solution with advanced Software
functionality with light show authorising software for dynamic color
changing effects. The controller has removable secure digital card
drive of 256 MB and has two DMX 512 Rj45 ports.ontrol Gear
Box,IP54 for housing contol component and other complete
accessories like cable tie, joining,splitter etc
nos 15.00 Rs. -
51
BCP 151, Integral LD bollard luminaire 800 mm in length, with
extruded aluminium body & polycarbonate difuser. The fixture is
IP65/ IK10.
nos 15.00 Rs. -
Sub Total of Electrical Works Rs. -
D) Auto Taxi Stand
Sr. No Description of Item Unit Quantity Rate in
INR Rate in Words ( Indian Rupee) Amount in INR
D Auto and Taxi Stand
1
Excavation for all types and sizes of foundations, trenches and drains or
for any other purpose including disposal of excavated stuff upto 1.5 m lift
and lead upto 50m (at least 5m away from the excavated area), including
dressing and leveling of pits.
In all types of soils.
A Depth of excavation up to 1.5 m Cum 1088.96 Rs. -
2
Filling from available excavated stuff (Excluding rock) in trenches, plinth,
sides of foundation etc. in layers not exceeding 20cm in depth
consolidating each deposited layer by ramming and watering with a lead
upto 50 M. and lift upto 1.5 M.
cum 35.15 Rs. -
3
Providing and filling in plinth with sand/ Crusher dust and hard moorum
under floor in layers not exceeding 20cm in depth consolidating each
deposited layer by ramming and watering, including dressing etc.
complete.
Cum 11.90 Rs. -
4
Providing and fixing form work including centring, shuttering, strutting,
staging, propping bracing etc. complete and including its removal at all
levels, for:
aFoundations, footings, bases of columns plinth beam, curtain wall in any
shape and size and all type of wall below plinth level.sqm 37.13 Rs. -
Bill of Quantity
Integrated Infrastructure Development Works for Phase-I works at sector-12, 40 and other Specified areas at Naya Raipur
85 of 109
D) Auto Taxi Stand
bWindow sills, anchor blocks, string course, bends, copings, bed plates and
like.sqm 3.44 Rs. -
cSuspended floors, roofs, access platform, balconies (plain surfaces) and
shelves (cast in situ)sqm 78.03 Rs. -
5
Clearing and grubbing road land including uprooting rank
vegetation, grass, bushes, shrubs, saplings and trees girth up to
300 mm, removal of stumps of trees cut earlier and disposal of
unserviceable materials and stacking of serviceable material to
be used or auctioned up to a lead of 1000 meters including
removal and disposal of top organic soil not exceeding 150 mm
in thickness if required and as per relevant clauses of section-
200.
a In area of light jungle ha 0.16 Rs. -
6
Providing and laying nominal mix plain cement concrete with crushed
stone aggregate using concrete mixer in all works upto plinth level
excluding cost of form work.
a1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm
nominal size).Cum 24.88 Rs. -
b1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm
nominal size).Cum 78.31 Rs. -
86 of 109
D) Auto Taxi Stand
c1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm
nominal size).Cum 6.64 Rs. -
7
Providing and laying design mix reinforcement cement concrete with crushed
graded stone aggregate 20mm nominal size using batching plant, transit
mixer and concrete pump, in all works upto floor five level excluding cost of
reinforcement and form work.
a M-25 (using minimum cement content 410 kg/cum concrete) Cum 7.80 Rs. -
8
Providing and laying pre-stressed cement concrete of M-35 grade in
superstructure including form work but excluding reinforcement complete
as per drawing and specifications and IS : 1343-2012.
Cum 23.04 Rs. -
9
Providing and placing in position reinforcement for R.C.C. work including
straightening, cutting, bending, binding etc. complete as per drawings
including cost of binding wire in foundation and plinth all complete
a Thermo-Mechanically treated bars FE 500D Kgs 2634.93 Rs. -
10
Construction of embankment with Material Obtained from
Borrow Pits/Borrow Area (Construction of embankment with
approved material/selected soil having C.B.R. (as specified
in the contract) obtained from borrow pits with all lifts
and leads, transporting to site, spreading, grading to required slope
and compacting to meet requirement of table 300-2)
Cum 790.50 Rs. -
11 Granular Sub-base as per Table:- 400-1
87 of 109
D) Auto Taxi Stand
Construction of granular sub-base by providing graded Material, ,
carriage of mixed Material to work site, spreading in uniform layers
with motor grader on prepared surface watering, rolling and
compacting with vibratory power roller at OMC to achieve the desired
density, complete as per clause 401(i) Grading (iii)
a Plant mix method (with Mechanically crushed stone only) 189.24 Rs. -
12
Dry Lean Cement Concrete Sub-base as per IRC:SP-49
(Construction of dry lean cement concrete Sub-base over a prepared
sub-grade with coarse and fine aggregate conforming to IS: 383, the
size of coarse aggregate not exceeding 26.5 mm, aggregate cement
ratio not to exceed 15:1, aggregate gradation after blending to be as
per table 600-1, cement content not to be less than 150 kg/cum,
optimum moisture content to be determined during trial length
construction, concrete strength not to be less than 10 Mpa at 7 days,
mixed in a batching plant, transported to site, laid with a paver with
electronic sensor, compacting with 8-10 tonnes vibratory roller,
finishing and curing as per clause 601.)
Cum 172.30 Rs. -
a
13
Footpaths and Separators (Construction of footpath/separator by
providing a 150 mm compacted granular sub base as per clause 401
and 75 mm thick cement concrete base with PCC grade M-15, over
laid with precast cement concrete tiles 25mm thick fixed in 20mm
thick cement mortar 1:3 including provision of all drainage
arrangements but excluding kerb channel excluding cost of GSB.) as
per clause 410.
Sqm 348.60 Rs. -
14
Random rubble masonry with hard stone in foundation and plinth in
Cement Mortar 1:6 (1 Cement : 6 Coarse Sand) including leveling up with
cement concrete 1:6:12 (1 cement : 6 coarse sand: 12 stone aggregate
20mm nominal size) upto plinth level.
Cum 90.14 Rs. -
15
Random rubble masonry with hard stone in foundation and plinth in
Cement Mortar 1:6 (1 Cement : 6 Coarse Sand) including leveling up with
cement concrete 1:6:12 (1 cement : 6 coarse sand: 12 stone aggregate
20mm nominal size) upto plinth level.
88 of 109
D) Auto Taxi Stand
a
Extra for random rubble masonry with hard stone in superstructure above
plinth level for every floor or part thereof in addition to rate for foundation
and plinth:
Cum 17.25 Rs. -
16
Cement Concrete Pavement (Construction of un-reinforced, dowel
jointed, plain cement concrete pavement over a prepared sub-base,
coarse and fine aggregate conforming to IS:383, and graded as per
table 600-3, mixed as per approved mix design at site, laid, spread,
vibrated, compacted and finished in a continuous operation including
provision of contraction, expansion, construction and longitudinal
joints, joint filler, separation membrane, sealant primer, joint sealant,
de-bonding strip, dowel bar, tie rod, admixtures as approved, curing
compound, finishing to lines and grades as per drawing as per clause
602.)
a With Cement concrete grade M-40 and minimum cement content @ 400 kg/cum.Cum 149.76 Rs. -
17Coursed rubble masonry (Second sort) with hard stone in Cement mortar
1:6 (1 cement : 6 coarse sand) upto plinth level.Cum 33.97 Rs. -
18Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to
IS:12894-2002 of class designation 4.0 in foundation and plinth in:
a Cement Mortar 1:4 (1 Cement : 4 Coarse Sand) Cum 6.62 Rs. -
19
Cast in Situ Cement Concrete M20 kerb (Construction of cement
concrete kerb with top and bottom width 115 and 165 mm
respectively, 250 mm high in PCC M20 grade on PCC M10 grade
foundation 150 mm thick, foundation having 50 mm projection
beyond kerb stone, kerb stone laid with kerb laying machine,
foundation concrete laid manually, all complete as per clause 409)
Meter 232.00 Rs. -
89 of 109
D) Auto Taxi Stand
20 Painting on Concrete Surfaces
aTwo coats on new surfaces (Painting two coats after filling the surface with
synthetic enamel paint in all shades on new plastered concrete surfaces)sqm 116.00 Rs. -
21
Providing and fixing factory made UPVC door frame made of UPVC profile
section having an overall dimension as below (tolerance ± 1mm) with
wall thickness 2.0mm ± 0.2mm, corners of the door frame to be jointed
with galvanized brackets and stainless steel screws, joints mitred and
plastic welded. The hinge side vertical of the frames reinforced by
galvanized M.S. tube of size 19 X 19mm and 1mm ± 0.1mm wall
thickness and 3 nos. stainless steel hinges fixed to the frame complete as
per manufacturers specification and direction of Engineer-in-charge
a Extruded section Profile size 48x40 mm. metre 12.00 Rs. -
22
Providing and fixing factory made PVC door shutters of specified
thickness made of styles and rails of a UPVC hollow section of specified
size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on
both sides. The styles and rails mitred and joined at the corners by means
of M.S. galvanised/ plastic brackets of size 75x220 mm having wall
thickness 1.0 mm and stainless steel screws.
a 24 mm thick door shutters with styles and rails of size 59x24 mm sqm 3.20 Rs. -
23
Steel work in tubular (round, square or rectangular hollow tubes etc.)
structure in built-up sections, trusses and frame work including cutting,
hoisting, fixing in position upto a height of 5m above plinth level,
consisting of columns trusses, roof and bottom purlins, base plate, holding
down bolts, wind ties bracing (if required), bolts, nuts and washers for
fastening etc. complete with applying a priming coat of red oxide zinc
chromate primer.
90 of 109
D) Auto Taxi Stand
a Electric resistance or induction butt welded tubes Grade-250 kg 4174.79 Rs. -
24
Steel work welded in built up sections/ framed work including cutting,
hoisting, fixing in position and applying a priming coat of red oxide zinc
chromate primer.
In gratings, frames, guard bar, ladder, railings, brackets, gates and similar
works.
a Angle 65x65x6 @ 5.0kg/m kg 2240.00 Rs. -
25
Supplying and fixing rolling shutter of approved makes made of M.S. laths
interlocked together through their entire length and jointed together at the
end by end locks, mounted on specially designed pipe shaft with brackets,
side guides and arrangements for inside and out side locking with push
and pull arrangement complete but excluding the cost of top cover and
spring.
a 80x1.25mm M.S. Laths sqm 31.50 Rs. -
26
Providing and fixing in position chain linked steel wire fabric made of 4mm
dia G.I. wire of required width in mesh to concrete/ wooden/ angl eiron posts
including securing and screwing with 2mm dia G.I. wire, G.I. staples, G.I.U-
nails or steel pins etc., complete.
a Aperture 50x50mm sqm 168.00 Rs. -
91 of 109
D) Auto Taxi Stand
27
Providing and fixing 12mm thick pre-laminated particle board flat pressed
with decorative lamination and balancing lamination on specified sides
exterior Grade – I MDF Board 12 mm thick confirming to IS:14587,
including fixed in aluminium doors, windows shutters and partition frames
with C.P. brass/ stainless steel screws etc. complete
a With decorative lamination on both side Sqm 2.52 Rs. -
28
Providing & fixing UV stabilized fibreglass reinforced plastic (FRP) sheet
roofing upto any pitch including fixing with polymer coated 'J' or 'L' hooks,
bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding
the cost of purlins, rafters, trusses etc. The sheets shall be manufactured
out of 2400 TEX panel rovings incorporating minimum 0.3% Ultra-violet
stabiliser in resin system under approximately 2400 psi and hot cured.
They shall be of uniform pigmentation and thickness without air pockets
and shall conform to IS 10192 and IS 12866.The sheets shall be opaque
or translucent, clear or pigmented, textured or smooth as specified.
a2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2"or 3"or 6") as
specified.sqm 161.20 Rs. -
29 Providing and making 12mm thick cement plaster of mix:
a In Cement Mortar 1:4 (1 cement : 4 fine sand) Sqm 194.91 Rs. -
30
Planting of Trees and their Maintenance for one Year
(Planting of trees by the road side (Avenue trees) in 0.60 m dia.
holes, 1 m. deep dug in the ground, mixing the soil with decayed
farm yard/sludge manure, planting the saplings, backfilling the
trench, watering, fixing the tree guard and maintaining the plants
for one year)
Each 36.00 Rs. -
92 of 109
D) Auto Taxi Stand
31Providing and making pointing on stone work with cement Mortar 1:3 (1
cement : 3 fine sand)
a Ruled pointing Sqm 272.76 Rs. -
32
Planting Permanent Hedges including Digging of Trenches
(Planting permanent hedges including digging of trenches, 60 cm
wide and 45 cm deep, refilling the excavated earth mixed with
farmyard manure, supplied at the rate of 4.65 cum per 100 meters
and supplying and planting hedge plants at 30 cm apart.)
Rmt 90.00 Rs. -
33
Providing and laying ceramic glazed floor tiles conforming to IS : 15622
of approved size, make, colour, shade laid on 20 mm thick Cement
Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with
white cement mixed with matching pigment etc., complete
a Size 300x300mm sqm 6.75 Rs. -
34
15 mm thick Table rubbed polished Granite stone slab flooring laid over
20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse
sand) laid and jointed with grey cement slurry including rubbing and
polishing etc. complete. (Area of slab should be 0.50 sqm and above)
a Granite stone black Sqm 8.00 Rs. -
35
Stone work with KOTA STONE Slab (machine cut edge) exposed face
machine cut and table rubbed with rough backing for wall lining etc.
(Veneer work) upto 10 metre height, backing filled with a grout of 20 mm
thick cement mortar 1:3 (1 cement: 3 coarse sand), jointing with cement
mortar 1:2 (1 cement: 2 stone dust) with admixture of pigment matching
the stone shade including rubbing and polishing complete. (To be secured
to the backing by means of cramps which shall be paid separately)
93 of 109
D) Auto Taxi Stand
a 25mm thick Sqm 51.15 Rs. -
36 Distempering with acrylic washable distemper to give an even shade
a On new work (Two or more coats) Sqm 201.21 Rs. -
37 Painting on new work (two or more coats) to give an even shade with:
a Satin synthetic enamel paint sqm 168.00 Rs. -
38
Providing and fixing vitreous china water closet (European type W.C.
pan) with white ISI marked plastic seat and lid, 10 litre low level white
P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings
and fixtures complete including cutting and making good the
walls and floors wherever required :
a White pedestal type each 2.00 Rs. -
39Providing and fixing white vitreous china urinal basin with waste fitting
as per IS : 2556, and other couplings in C.P. brass complete:
a Flat back half stall urinal of size 460x380x250mm each 2.00 Rs. -
94 of 109
D) Auto Taxi Stand
40Providing and fixing white vitreous china wash basin including making
all connections but excluding the cost of fittings :
a White Size 550x450 mm each 2.00 Rs. -
41Providing and fixing vitreous china pedestal for wash basin completely
recessed at the back for the reception of pipes and fittings.
a White each 2.00 Rs. -
42
Providing and fixing on wall face or under floor UV stabilized Unplasticised
Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming
to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring
conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc
complete.
a 75 mm dia pipe metre 30.00 Rs. -
b 110 mm dia metre 10.00 Rs. -
43
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded
fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes
conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS :
5382 leaving 10 mm gap for thermal expansion.
95 of 109
D) Auto Taxi Stand
a Tee/ Tee with door/ Bend 45°/ Bend 90°
75 mm Nos. 1.00 Rs. -
b Double "Y" with or without door
75 mm Each 1.00 Rs. -
c Vent covel
110 mm Nos. 1.00 Rs. -
d Access door cap
75 mm Each 2.00 Rs. -
e 110 mm Each 2.00 Rs. -
96 of 109
D) Auto Taxi Stand
f P trap 110mmx110mm long Nos. 1.00 Rs. -
g Nahani trap 110x75mm Nos. 1.00 Rs. -
44
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank ISI : 12701 marked with cover and suitable locking
arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank
a 2 nos of tank @ 1000 Liter each litre 2000.00 Rs. -
45
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply including all CPVC plain & brass
threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings with one step CPVC solvent cement and
testing of joints complete as per direction of Engineer in Charge.
a 20 mm nominal outer dia .Pipes. metre 30.00 Rs. -
b 32 mm nominal outer dia .Pipes. metre 20.00 Rs. -
97 of 109
D) Auto Taxi Stand
c 40 mm nominal outer dia .Pipes. metre 10.00 Rs. -
46Providing and fixing 15 mm nominal bore Brass bib/stop cock of
approved quality:
a Bib cock (250 grams) each 3.00 Rs. -
b Stop cock (350 grams) each 2.00 Rs. -
47
Constructing masonry Chamber 60x60x75 cm, inside with modular well
burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160
mm bottom diameter and 180 mm deep (inside) with chained lid and RCC
top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size) necessary excavation foundation concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)
and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand)
12 mm thick finished with a floating coat of neat cement complete as per
standard design :
each 2.00 Rs. -
48
Providing, lowering, laying, aligning, fixing in position at and jointing at all
level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer
application as per IS 14333-1996 (amended upto date) in trenches in
complete including all material, labour, testing and commissioning as per
direction of Engineer.
Note : E/w to be measured and paid separately.
a 200 mm dia Rmt 50.00 Rs. -
98 of 109
D) Auto Taxi Stand
49
Providing and fixing M.S. flat iron tree guard 60cm dia. and 2m height
above ground level formed of 4 nos. 25x6mm and 8 nos. 25x3mm vertical
M.S. flats riveted to 3 nos. 25x6mm M.S. flat iron rings in two halves,
bolted together with 8mm dia. and 30mm long bolts including painting two
coats with paint of approved brand and manufacture over a coat of
priming, complete in all respects.
Nos 36.00 Rs. -
50
Supply of hot dipped galvanized (in single dip to average 70 micron)
octoganal pole made of 4mm thick steel plate having base plate
200x200x12mm, window and flush cover with locking arrangement at
suitable height from base for cable termination block, pole suitably reinforced
with welded steel section at window cut section to make the strength of pole
unaffected, including template and anchor plate 240x240x3mm with 4 nos
450mm long, 16mm dia foundation bolts bolts (EN8 grade).
a 5 metre high, minimum dia 129mm at bottom and 75mm at top Each 8.00 Rs. -
51
Supply and fixing following street light pole bracket on existing pole made
out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy
of suitable dia at a angle of 102.50 including having MS triangular stiffner of
size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket
with pole by providing suitable size heavy duty nuts and bolts in canopy,
painting with one coat of approved steel primer etc. as required.
a Single Over Hang 0.75 metre Long Each 8.00 Rs. -
52Erection of GI octogonal pole on existing cement concrete foundation
having grouted bolts and nuts, aligning in true vertical position as required.
99 of 109
D) Auto Taxi Stand
a 5 metre high Each 8.00 Rs. -
53
Designing and providing suitable RCC foundation for 5m metre high GI
octagonal pole including steel reinforcement (minimum 90kg per cum), form
work, embeding 2 nos 50mm dia PVC pipe for cable entry in each
foundation, excavation disposal of surplus soil and curing etc. as required.
(size: 400 x 400 x 1200mm)
cum 6.00 Rs. -
54
Supplying ,installation ,Testing & Commissioning of 25W IP65 LED
streetlight Luminaire complete with pressure die cast aluminum housing.
The fixture shall be designed so as to have lumen maintenance of at least
70% at the end of 50,000 hours.
each 8.00 Rs. -
55
Supply and drawing following sizes of FR PVC insulated copper conductor,
single core cable in the existing surface/ concealed, steel/ PVC conduit as
required.
a 3x1.5 sq.mm. (from Pole Junction box to Light fitting) Mts 50.00 Rs. -
56
Supplying and fixing SP MCB, 240 volts, 'B' series, suitable for lighting and
other loads in the existing MCB DB complete with connections, testing and
commissioning etc. as required.
a SPMCB 10 A inside the box for cable connection Each 8.00 Rs. -
57
Supplying and laying double wall HDPE pipe having corrugation on the
outer wall and plan surface on inner wall in ground below road, path etc at a
depth not less than 100 cm excluding excavation, dismantling of road if
required and refilling the trench etc. as required.
100 of 109
D) Auto Taxi Stand
a 40 mm Outer dia. mtr 300.00 Rs. -
58Supplying and fixing of following sizes PVC conduit along with accessories
in surface complete as required.
a 20 mm mtr 250.00 Rs. -
59
Earthing with GI earth pipe 4.5 mtr long, 40 mm dia including accessories,
and providing masonry enclosure with cover plate having locking
arrangement and watering pipe etc. with charcoal and salt as required.
Nos. 4.00 Rs. -
60
Supplying and laying 6 SWG G.I. Wire at 0.50 meter below ground level for
conductor earth electrode, including soldering, excavation and refilling the
trench etc. as required.
mtr 70.00 Rs. -
LT Panel-Utility
Fabrication, supply, installation, testing and commissioning of cubicle type
compartmentalized wall/ floor mounted power cum control panel board of
specified size and 900mm (NS) deep made out of not less than 2 mm thick
CRCA MS sheet with suitable size compartments for bus bars, switchgears
and necessary cutouts for voltmeters, ameters ets as per specifications
including powder coating painting but without busbars, switchgears and other
accessories etc complete as required for completeness and as per attached
specification, direction of Engineer, CGPWD standards and Electrical
Inspectorate standards. (Only face area is to be measured)
Rs. -
INCOMER
1 No. 100A FP MCCB(35 KA)
Metering & Indication
1 set of phase indicating lamps
1 set of (0-500V) Voltmeter with VSS
1 set of (0-100A) Ammeter with ASS with 3 no s.100/5A CTs
BUS-BAR
1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves
OUTGOINGS
61set 1.00
101 of 109
D) Auto Taxi Stand2 Nos. 32A TPN MCCB (35KA) ,3 Nos 32 A SP MCCB (35KA)
1 No.32 A DP contactor ,AOM switch & 24 hrs setting
62
Supplying and laying following sizes one number XLPE, steel armoured,
aluminium conductor Power cable of 1.1 KV grade in existing RCC/ HUME/
STONEWARE/ METAL pipe as required for completeness and as per
attached specification, direction of Engineer, CGPWD standards and
Electrical Inspectorate standards.
a 3.5 x 50 sq. mm. Mtr. 70.00 Rs. -
b 4x25 sq.mm Mtr. 100.00 Rs. -
c 2 x 10 sq. mm. Mr. 150.00 Rs. -
63
Supplying and making end termination with brass compression gland and
aluminum lugs for following sizes armoured aluminium conductor power
cable of 1.1KV grade along with accessories, hardwares etc as required for
completeness and as per attached specification, direction of Engineer,
CGPWD standards and Electrical Inspectorate standards.
Mtr.
a 3½ X 50 sq. mm Each 3.00 Rs. -
61set 1.00
102 of 109
D) Auto Taxi Stand
b 4x25 sq.mm Each 2.00 Rs. -
c 2 x 10 sq. mm. Each 18.00 Rs. -
64
Point Wiring for light/ fan/ exhaust fan/ call bell point with 1.5 sqmm FR
PVC insulated stranded copper conductor single core cable in concealed
PVC conduit, with 5 amp modular switch, modular base and cover plate,
suitable size G.I. box and earthing the point with same size cable along with
accessories, hardwares etc as required for completenessand as per
attached specification, direction of Engineer, CGPWD standards Electrical
Inspectorate standards
a Short Point Point 15.00 Rs. -
b Medium Point Point 10.00 Rs. -
c Long Point Point 5.00 Rs. -
103 of 109
D) Auto Taxi Stand
65
Point wiring for light plug point with 2 x 2.5 sq mm FR PVC insulated
stranded copper conductor single core cable cable in concealed PVC conduit
along with modular type 6 amp switch and 3 pin 6 amps socket outlet with
modular base and cover plate, suitable size G.I. box, earthing the switch box
and socket outlet with same size cable along with accessories, hardwares
etc. as required for completenessand as per attached specification, direction
of Engineer, CGPWD standards and Electrical Inspectorate standards.
a Medium Point Point 6.00 Rs. -
66
Circuit/ sub main wiring along with earth wire with the following sizes of FR
PVC insulated copper conductor, single core cable in concealed PVC
conduit along with accessories, hardwares etc. as required.for completeness
and as per attached specification, direction of Engineer, CGPWD standards
and Electrical Inspectorate standards.
a 3 X 1.5 sq. mm in 20mm conduit Mtr. 50.00 Rs. -
b 3 X 2.5 sq. mm in 20mm conduit Mtr. 15.00 Rs. -
67
Wiring for light/ fan/ exhaust fan / call bell point with 1.5 sqmm FR PVC
insulated stranded copper conductor single core cable in surface PVC
conduit, with 5 amp piano type switch, phenolic laminated sheet, suitable
size M.S. box and earthing the point with same size cable etc as required.
Mtr.
a Medium Point Point 5.00 Rs. -
104 of 109
D) Auto Taxi Stand
b Long Point Point 5.00 Rs. -
68
Extra for providing and fixing light plug point on board in surface PVC conduit
point wiring with piano type 3 pin 5 amp socket outlet and 5 amp switch
including cost of phenolic laminated sheet and M.S. box etc. as required.etc.
as required.
Point 10.00 Rs. -
69
Wiring for circuit/ sub main wiring along with earth wire with the following
sizes of FR PVC insulated copper conductor, single core cable in surface
PVC conduit etc as required.
Point
a 3 X 1.5 sq. mm in 20mm conduit 20.00 Rs. -
70
Supplying and fixing metal box of following sizes (nominal size) in recess
with suitable size phenolic laminated sheet cover in front including painting
etc as required.
a 150 mm X 150 mm X 60 mm deep Mtr 10.00 Rs. -
71
Supplying and fixing following size/ modules GI box with modular base &
cover plate for modular switches in recess etc. as required for competeness
and as per attached specification, direction of Engineer, CGPWD standards
and Electrical Inspectorate standards.
105 of 109
D) Auto Taxi Stand
a 125mmX75mm (4 Module) Each 15.00 Rs. -
72
Supplying and fixing modular stepped type electronic fan regulator (two
module size) moving all rounds on the existing modular plate and switch box
including connections but excluding modular plate etc. as required.
Each 6.00 Rs. -
73
Supplying and fixing 3 pin, 5 amp ceiling rose of approved make and ISI
quality on the existing metal box including connections along with
accessories, hardwares etc as required for competeness and as per
attached specification, direction of Engineer, CGPWD standards and
Electrical Inspectorate standards.
Each 6.00 Rs. -
74
Supplying and fixing polycarbonate batten/ angle holder of approved make
and ISI quality including connections along with accessories, hardwares etc
as required for competeness and as per attached specification, direction of
Engineer, CGPWD standards and Electrical Inspectorate standards.
Each 6.00 Rs. -
75
Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm
(max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC
slab along with accessories, hardwares etc as required for competeness
and as per attached specification, direction of Engineer, CGPWD standards
and Electrical Inspectorate standards.
Each 6.00 Rs. -
76
Supplying, installation, testing and commissioning of following sizez ceiling
fan of approved make and ISI quality including the down rods of 30 cm
wiring with1.5 sq. mm FR PVC insulated, copper conductor, single core
cable, earthing, connections along with accessories, hardwares etc as
required for completeness and as per attached specification, direction of
Engineer, CGPWD standards and Electrical Inspectorate standards.
a 1050 mm sweep Each 5.00 Rs. -
106 of 109
D) Auto Taxi Stand
b 1200 mm sweep Each 1.00 Rs. -
77
Supplying, installation, testing and commissioning of following sizes exhaust
fan (heavy duty) of approved make and ISI quality in existing opening in wall
including earthing, connections along with accessories, hardwares etc as
required for competeness and as per attached specification, direction of
Engineer, CGPWD standards and Electrical Inspectorate standards.
`
a 300 mm sweep Each 2.00 Rs. -
78Supplying, installation, testing and commissioning of following surface LED
light
a
18watt LED Tube Light Fixture
1x18watt T8 LED tube 4 ‘ length made of full polycarbonate housing with
integral driver suitable for retrofitting in an existing luminaire mounted on
decorative batton. Rating of tube 18 W + 10% , 240 V , 50 Hz. Operating
voltage : 140-280 V . Terminal should be suitable for wiring from one side
only . Lumen output ≥1900 Lumens. Colour temperature 6500K + 200 , CRI
≥ 80 , System efficacy ≥ 100 lm/W. Driver efficiency ≥ 85 % , AthD < 15% ,
Pf ≥ 0.95. Driver protection : Open circuit, Short circuit, Reverse polarity,
Surge protection : 2.5 kV, High Temperature. LED is LM 80 certified and
LM79 report is Certified by NABL Accredited lab. LED tube is also RoHS &
CE rated.
Each 15.00 Rs. -
79supplying ,fixing ,testing and commissioning of follwing CFL in existing
lighting luminaries as required
107 of 109
D) Auto Taxi Stand
a 15 Watt Each 5.00 Rs. -
80
Supplying and fixing on surface/ recess following way, 240 volts SP&N, MCB
distribution board consumer unit of sheet steel phosphatized and powder
painted complete with tinned copper busbar, neutral busbar, earth bar, din
bar, detachable gland plate, including interconnections, earthing etc. as
required. (But without MCB/ RCCB/ Isolator)
a 4 way, single door Each 7.00 Rs. -
81
Supplying and fixing SP MCB, 240 volts, 'C' series, suitable for inductive
loads in the existing MCB DB complete with connections, testing and
commissioning etc. as required.
a 6 amps to 32 amps Each 21.00 Rs. -
81
Supplying and fixing following rating, 240 volts TWO POLE
ISOLATOR in the existing MCB DB complete with connections,
testing and commissioning etc. as required
a 40 amps Each 7.00 Rs. -
108 of 109
D) Auto Taxi Stand
82 Design,Fabrication,supply,installation,testing and commissioning of pedestal mounted Block Main Power Board, made out of 2 mm thick CRCA sheet steel, cubicle type,FRLSee standing,dust/vermin/ weather proof with busbars, switchgears,earth bus etc including powder coated painting along with accessories,hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. The panel box shall house : 1 No 4 pole 63A isolator as Incomer ; 100A four pole Copper busbrs,6 Nos 16A SP MCB , C series, 10kA as outgoing feeders:6 Nos lockable compartments for housing kWh meters Interconnection by Copper insulated leads(DOUBLE DOOR TYPE)Each 1.00 Rs. -
Sub total of Auto Taxi Stand Rs. -
109 of 109