Download - RUT240 - storage.googleapis.com
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
RUT240
DATASHEET // RUT240
HARDWARE
POWER SOCKET PINOUT
FRONT VIEW
BACK VIEW
2Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
3
4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps
Direct connection (bridge) between mobile ISP and device on LAN
SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP
Router assigns its mobile WAN IP address to another device on LAN
Auto APN
Operator black/white list
Possibility to use different PDNs for multiple network access and services
Band lock, Used band status displayBand management
Black/White list
Multiple PDN (optional)
WPA2-Enterprise - PEAP, TLS, TTLS, AES-CCMP, TKIP, Auto Cipher modes, Client separation
SSID stealth mode and access control based on MAC addressSSID
WiFi security
Passthrough
APN
Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, RIPng, OSPF6)
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPnP, SSH, DHCP, Telnet, SMNP, MQTT, Wake On Lan (WOL)
Ping Reboot, Periodic Reboot, LCP and ICMP for link inspection
Port forward, traffic rules, custom rulesFirewall
Network protocols
Connection monitoring
Routing
VoIP passthrough support
Static and dynamic IP allocation, DHCP Relayd
Traffic priority queuing by source/destination, service, protocol or port, traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
Supported >25 service providers, others can be configured manually
VRRP, Mobile, Wired and WiFi WAN options, each of which can be used as backup, using automatic Failover
Balance your internet traffic over multiple WAN connectionsLoad balancing
DDNS
Network backup
Mobile connection management, data compression VPN client (not available in standard FW)
Possibility to mount remote file system via SSH protocol (not available in standard FW)
NetSnapper (optional)
SSHFS (optional)
1-255
Allow access through WANAllow Remote Access
ID range
Modbus TCP custom register block requests, which read/write to a file inside the router, and can be used to extend Modbus TCP Slave functionalityCustom registers
DHCP
QoS / Smart Queue Management (SQM)
Status Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP Bytes sent/received
Bridge
WPA2-Enterprise (with external/internal Radius server), WPA2-PSK, WPA-PSK, WEP, MAC Filter
IEEE 802.11b/g/n, Access Point (AP), Station (STA)Wireless mode
WiFi
1 x LAN port, 10/100 Mbps, comply IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX
1 x WAN port (can be configured to LAN) 10/100 Mbps, comply IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIXWAN
LAN
SMS
MOBILE
Mobile module
WIRELESS
ETHERNET
NETWORK
MODBUS TCP SLAVE
Up to 50 simultaneous connections
Captive portal (Hotspot), internal/external Radius server, built in customizable landing pageWireless Hotspot
WiFi users
DATASHEET // RUT240
FEATURES
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
4
Multiple clients and server can be running simultaneously, 12 encryption methods
DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC
01, 02, 03, 04, 05, 06, 15, 16
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit float (Big endian, Big endian with byte-swapped, Little endian, Little endian with byte-swapped)
OpenVPN Encryption
VPN
OpenVPN
Firmware update from sever, automatic notificationFOTA
HTTP/HTTPS, status, configuration, FW update, CLI ,troubleshoot, event log, system log, kernel log
MONITORING & MANAGEMENT
WEB UI
MODBUS TCP MASTER
Pre-shared key, digital certificates, X.509 certificates
Pre-configured firewall rules can be enabled via web-ui, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention ( SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
Attack prevention
Authetication
Firewall
WPA2-Enterprise – PEAP, EAP-TLS, TLS, TTLS. AES-CCMP, TKIP, Auto Cipher modes, Client separation
Tag based VLAN separation
WiFi security
VLAN
Set up custom data limits for the SIM card
Blacklist for blocking out unwanted websites, whitelist for specifying allowed sites only
Flexible access control of TCP, UDP, ICMP packets, MAC address filter
Mobile quota control
WEB filter
IKEv1, IKEv2, supports up to 4 x VPN IPsec tunnels (instances), with 5 encryption methods (DES, 3DES, AES128, AES192, AES256)
GRE tunnel
IPsec
GRE
Client/Server services can run simultaneously
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the programs' code
PPTP, L2TP
Stunnel
SSTP client instance support
ZeroTier VPN
SSTP
ZeroTier
SSH (v1, v2)
SMS status, SMS configuration, send/read SMS via HTTP POST/GET
SSH
SMS
Reboot, Status, WiFi on/off, Mobile data on/off, Output on/off
OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
CALL
TR-069
MQTT Broker, MQTT publisher
SNMP (v1, v2, v3), SNMP trap
MQTT
SNMP
Management API over HTTP/HTTPSJSON-RPC
MODBUS TCP status/control
Teltonika Remote Management System (RMS)
Modbus
RMS
Supported functions
HTTP(S), MQTT, Azure MQTT
Allows sending commands and receiving data from Modbus Master through MQTT broker
MODBUS DATA TO SERVER
Protocol
MQTT GATEWAY
MQTT gateway
Supported data formats
SECURITY
Access control
DATASHEET // RUT240
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
5
IoT PLATFORMS
SYSTEM CHARACTERISTICS
FIRMWARE / CONFIGURATION
FIRMWARE CUSTOMIZATION
POWER
PHYSICAL INTERFACES (PORTS, LEDS, ANTENNAS, BUTTONS, SIM)
Can send device IP, Number of bytes send/received/ 3G connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, Sim State, PIN state, GSM signal, WCDMA RSCP WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server
Azure IoT Hub
Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IPCumulocity
Allows monitoring of: Device data, Mobile data, Network info, Availability
Allows monitoring of: WAN Type, WAN IP Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
Clouds of things
ThingWorx
Atheros Hornet, MIPS 24Kc, 400 MHzCPU
64 MB, DDR2
16 MB SPI Flash
RAM
FLASH memory
Update FW from file, check FW on server, configuration profiles, configuration backup, restore pointWEB UI
Update FW/configuration from server
Update FW/configuration for multiple devices
FOTA
RMS
Update FW without losing current configurationKeep settings
RutOS (OpenWrt based Linux OS)Operating system
Busybox shell, Lua, C, C++
SDK package with built environment provided
Supported languages
Development tools
4 pin industrial DC power socketConnector
9 – 30 VDC (4 pin industrial socket), reverse polarity protection, surge protection >33 VDC 10us max
Passive PoE over spare pairs (available from HW revision 0007 and batch number 0010). Possibility to power up through LAN port, not compatible with IEEE802.3af and 802.3at
Input voltage range
PoE (passive)
< 5 WPower consumption
2 x RJ45 ports, 10/100 MbpsEthernet
1 Digital Input, 1 Digital Output on 4 pin power connector
3 x connection type status LEDs, 5 x connection strength LEDs, 2 x LAN status LEDs, 1 x Power LED
I/Os
Status LEDs
1 x SIM slot (Mini SIM – 2FF), 1.8 V/3 V, external SIM holderSIM
4 pin DC connector
2 x SMA for LTE, 1 x RP-SMA for WiFi antenna connectors
Power
Antennas
Reset/restore to default buttonReset
DATASHEET // RUT240
INPUT/OUTPUT
1 x Digital non-isolated input (on 4 pin power connector)Input
1 x Digital open collector output (30 V, 300 mA, on 4 pin power connector)
SMS, EMAIL, RMS
Output
Events
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
EN 61000-4-3:2006 + A1:2008 + A2:2010
EN 61000-4-4:2012
RS
EFT
EN 61000-4-5:2006Surge immunity (AC Power Line)
EN 61000-4-5:2014, clause 7.1 of ITU-T K21
EN 61000-4-6:2009
Surge immunity (Ethernet ports)
CS
EN 61000-4-11:2004DIP
6
PHYSICAL SPECIFICATION
OPERATING ENVIRONMENT
Aluminum housing, plastic panels
74 x 83 x 25 mm (L x W x H)
125 g
Casing material
Dimensions
-40 C to 75 C
10 % to 90 % non-condensing
Operating temperature
Operating humidity
Bottom and sideways DIN rail mounting slots
Weight
Mounting options
IP30
310000 h
Ingress Protection Rating
MTBF
REGULATORY & TYPE APPROVALS
CE/RED, FCC, IC/ISED, EAC, RCM, PTCRB, RoHS, WEEE, Wi-Fi Certified, CCC, Anatel, GCF, REACH, Thailand NBTC, Ukraine UCRF, SDPPI (POSTEL)
Verizon, AT&T
Regulatory
Operator
EMI IMMUNITY
Draft EN 301 489-1 V2.2.0, Draft EN 301 489-17 V3.2.0, Draft EN 301 489-52 V1.1.0FCC 47 CFR Part 15B (2017), ANSI C63.4 (2014)
EN61000-4-2:2009
Standards
RF
EN 300 328 V2.1.1, EN 301 511 V12.5.1, EN 301 908-1 V11.1.1, EN 301 908-2 V11.1.1, EN 301 908-13 V11.1.1FCC 47 CFR Part 15C (2017), FCC 47 CFR Part 2 (2017), FCC 47 CFR Part 22H (2017), FCC 47 CFR Part 24E (2017), FCC 47 CFR Part 27C (2017)RSS-Gen Issue 4 (2014), RSS-247 Issue 2 (2017), RSS-132 Issue 3 (2013), RSS-133 Issue 6 (2013), RSS-139 Issue 3, RSS-130 Issue 1AS/CA S042.1:2018, AS/ACIF S042.3:2005, AS/CA S042.4:2018, AS/NZS 4268:2017
Standards
SAFETY
EN 300 328 V2.1.1, EN 301 511 V12.5.1, EN 301 908-1 V11.1.1, EN 301 908-2 V11.1.1, EN 301 908-13 V11.1.1FCC 47 CFR Part 15C (2017), FCC 47 CFR Part 2 (2017), FCC 47 CFR Part 22H (2017), FCC 47 CFR Part 24E (2017), FCC 47 CFR Part 27C (2017)RSS-Gen Issue 4 (2014), RSS-247 Issue 2 (2017), RSS-132 Issue 3 (2013), RSS-133 Issue 6 (2013), RSS-139 Issue 3, RSS-130 Issue 1AS/CA S042.1:2018, AS/ACIF S042.3:2005, AS/CA S042.4:2018, AS/NZS 4268:2017
Standards
ESD
DATASHEET // RUT240
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
7
DATASHEET // RUT240
1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.2. Use login information shown in image A when prompted for authentication.3. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory, and you will not be able to interact with the router's WebUI before you change the password.4. When you change the router's password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the router's main operating parameters. 5. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.
A. B.
admin
admin01
Bytes received/sent*
SIM card slot in use
Data connection state
State
-65 dBm
Connected
Registered (home); OPERATOR; 4G (LTE)
Ready
348.7 KB / 223.5 KB
LOGIN TO DEVICE
1. Push the SIM button with the SIM needle.2. Pull out the SIM holder.3. Insert your SIM card into the SIM holder.4. Slide the SIM holder back into the router.5. Attach Mobile and WiFi antennas.6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.7. Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to LAN port.
HARDWARE INSTALLATION
*Order code dependent.**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.
Bundled accessories specifications*
Radio specifications
RF technologies
Max RF power
2G, 3G, 4G, WiFi
33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@ WiFi
Mobile antenna 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain** 3 dBi, omnidirectional, SMA male connector
Power adapter Input: 0.4A@100-240VAC, Output: 9VDC, 1A, 4-pin plug
WiFi antenna 2400~2483.5 MHz, 50 Ω, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector
TECHNICAL INFORMATION
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
8
STANDARD PACKAGE CONTAINS
• RUT240• 2 x LTE antennas (swivel, SMA male)• 1 x WiFi antenna (swivel, RP-SMA male)• Euro PSU• Ethernet cable (1.5 m)• QSG (Quick Start Guide)• Packaging box
DATASHEET // RUT240
WHAT'S IN THE BOX?
RUTX240
EURO PSU
1 X WIFI ANTENNA (SWIVEL, RP-SMA MALE)
ETHERNET CABLE (1.5 M)
2 X LTE ANTENNAS (SWIVEL, SMA MALE)
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
9
DATASHEET // RUT240
PRODUCT CODE PACKAGE CONTAINSHS CODE HTS CODE
STANDARD ORDER CODES
RUT240 06E000
For more information on all available packaging options – please contact us directly.
851762 8517.62.00 Standard package
PRODUCT CODE FREQUENCYREGION (OPERATOR)
STANDARD ORDER CODES
RUT240 *8****
The price and lead-times for region (operator) specific versions may vary. For more information please contact us.
1 - Router is not certified on T-Mobile, Bell network (In progress).
Europe, the Middle East, Africa, Korea, Thailand, India, Malaysia
4G (LTE-FDD): B1, B3, B7, B8, B20, B28A4G (LTE-TDD): B38, B40, B413G: B1, B82G: B3, B8
RUT240 *0**** Europe, the Middle East, Africa, Korea, Thailand, India, Malaysia
4G (LTE-FDD): B1, B3, B5, B7, B8, B204G (LTE-TDD): B38, B40, B413G: B1, B5, B8
RUT240 *1**** North America (AT&T, Bell, T-Mobile)1
RUT240 *2**** North America (Verizon)
4G (LTE-FDD): B2, B4, B123G: B2, B4, B5
RUT240 *3**** Australia (Telstra) 4G (LTE-FDD): B1, B3, B5, B7, B283G: B1, B5
4G (LTE-FDD): B4, B13
2G: B3, B8
RUT240 *4**** South America, Australia, New Zealand, Taiwan
4G (LTE-FDD): B1, B2, B3, B4, B5, B7, B8, B284G (LTE-TDD): B403G: B1, B2, B5, B82G: B2, B3, B5, B8
RUT240 *7**** Global
4G (LTE-FDD): B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B284G (LTE-TDD): B38, B39, B40, B413G: B1, B2, B4, B5, B6, B8, B192G: B2, B3, B5, B8
RUT240 *0*00G Europe, the Middle East, Africa, Korea, Thailand, India (Vodafone)
4G (LTE-FDD): B1, B3, B5, B7, B8, B204G (LTE-TDD): B38, B40, B413G: B1, B5, B82G: B3, B8
RUT240 *6**** Europe, the Middle East, Africa, Korea, Thailand, Malaysia
4G (LTE-FDD): B1, B3, B7, B8, B20, B28A3G: B1, B82G: B3, B8
RUT240 *5**** Japan 4G (LTE-FDD): B1, B3, B8, B18, B19, B264G (LTE-TDD): B413G: B1, B6, B8, B19
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
10
DATASHEET // RUT240
MOUNTING OPTIONSDIN RAIL KITParameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
Value
35mm DIN Rail
Low carbon steel
57g
Philips Pan Head screw #6-32×3/16, 2pcs
82 mm x 46 mm x 20 mm
V
DIN RAIL KIT
DIN Rail adapter
Philips Pan Head screw #6-32×3/16, 2pcs for RUT2xx/RUT9xx
ORDER CODE HTS CODEPRODUCT CODE HS CODE
088-00267
For more information on all available packaging options – please contact us directly.
PR5MEC00 73269098 7326.90.98
SURFACE MOUNTING KITParameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
Value
Flat surface mount
ABS + PC plastic
2x5 g
Philips Pan Head screw #6-32×3/16, 2pcs
25 mm x 48 mm x 7.5 mm
V
DIN RAIL KIT
Surface mounting kit
Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE HTS CODEPRODUCT CODE HS CODE
088-00281
For more information on all available packaging options – please contact us directly.
PR5MEC12 73269098 7326.90.98
COMPACT DIN RAIL KITParameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
Value
35mm DIN Rail
ABS + PC plastic
6.5 g
Philips Pan Head screw #6-32×3/16, 2pcs
70 mm x 25 mm x 14,5 mm
V
DIN RAIL KIT
Compact plastic DIN Rail adapter (70x25x14,5mm)
Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE HTS CODEPRODUCT CODE HS CODE
088-00270
For more information on all available packaging options – please contact us directly.
PR5MEC11 73269098 7326.90.98
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
RUT240 SPATIAL MEASUREMENTS & WEIGHT
11
DATASHEET // RUT240
MAIN MEASUREMENTS
H x W x D dimensions for RUT240:
Device housing*:
Box:
83 x 74 x 25
173 x 148 x 71
TOP VIEW
The figure below depicts the measurements of RUT240 and its components as seen from the top:
RIGHT VIEW
The figure below depicts the measurements of RUT240 and its components as seen from the right side:
*Housing measurements are presented without antenna connectors and screws; for measurements of other device elements look to the sections below.
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
12
DATASHEET // RUT240
The figure below depicts the measurements of RUT240 and its components as seen from the front panel side:
FRONT VIEW
The figure below depicts the measurements of RUT240 and its components as seen from the back panel side:
REAR VIEW
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
The figure below depicts an approximation of the device's dimensions when cables and antennas are attached:
12
DATASHEET // RUT240
MOUNTING SPACE REQUIREMENTS
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.
12
DATASHEET // RUT240
The scheme below depicts protrusion measurements of an attached DIN Rail:
DIN RAIL
Copyright © 2020, Teltonika Networks. Specifications and information given in this document are subject to change by Teltonika Networks without prior notice.