1
Tombstone Ring Toss
Pegboards:2 large squares1 large circle
Other:Heavy cardboardGlue or velcro
Bead Colors:Magenta - 54Orange - 54Creme - 36Cheddar - 8Prickly Pear - 54Kiwi Lime - 54Pastel Green - 28Green - 14Dark Green - 198Turquoise - 54Plum - 54Purple - 54Light Brown - 112Brown - 603Grey - 944Dark Grey - 396Black - 766White - 58Raspberry Pearl Stripe - 48Fire Stripe - 48Prickly Pear Pearl Stripe - 48Cucumber Stripe - 84Royal Blue Pearl Stripe - 48Starry Nite Stripe - 48Grape Stripe - 48Monkey Stripe - 150Zebra Stripe - 70Silver Pearl Stripe - 124
Instructions1. Place your beads on the pegboards as shown. If you are using a clear
pegboard, slide the actual-size pattern underneath it.2. Ask an adult to fuse your designs—see page 9 for further instructions.3. Assembly: see page 10.
YOU WILL NEED:
RIP Tombstone
Tombstone Ring Toss GameCreate a spooky cemetery scene on a heavy cardboard surface using the Perler pieces and your favorite props. Glue or velcro your pieces in place.
Determine where the player must stand to play. Assign points for successfully ringing the various objects:
• 10 points for either of the small tombstones
• 30 points for the skull tombstones
• 40 points for the RIP tombstone
• 50 points for either of the zombie hands alone
• 100 points for the tree monster top or arms
• Hit the gates at all, you lose all your points!
2
Tombstone Ring Toss
Bead Colors: CremeCheddarGreyDark GreyBlackWhiteZebra StripeSilver Pearl Stripe
Skeleton Tombstone
MAKE 2all pieces
Candles
Tombstone Ring Toss
3
Bead Colors: CheddarPastel GreenGreenDark GreenLight BrownGreyDark GreyBlackCucumber StripeZebra Stripe
Small Tombstones
MAKE 2all pieces
ZombieHands
Tombstone Ring Toss
4
Bead Color:Black
Gate
MAKE 2
Tombstone Ring Toss
5
Bead Colors: Kiwi LimeDark BrownBlackMonkey Stripe
Tree Monster Top
Tree Monster: The main part of the tree monster is created on two square pegboards assembled as shown at right. Cut out these two patterns and tape them together in the same way.
Tombstone Ring Toss
6
Bead Colors: Dark BrownBlackMonkey Stripe
Tree Monster Trunk
Tombstone Ring Toss
7
Bead Colors: Dark BrownBlackMonkey Stripe
Tree Monster Base
Tombstone Ring Toss
8
Bead Colors: Dark BrownBlackMonkey Stripe
Tree Monster Arms
9
Tombstone Ring Toss
Rings: Using the same pattern, make 9 rings in the color combinations. The first color listed is for the outside, the second color is for the inside.
1. Place your pegboard on a flat, heat-safe surface.
2. Set a household iron to the medium setting. Place ironing paper over the pegboard. In a circular motion, begin to iron the project. Do not press down with the iron. As the beads begin to fuse, you will see circles of the beads start to show through the paper. When ironed properly, the beads will still have an open center. Let the design cool.
3. Remove the paper and bead design from the peg board. Flip the design over to expose the non-fused side. Repeat step two. Let cool completely.
NOTE: Beads need heat for about 10-20 seconds per side to fuse evenly. Lift the paper occasionally to see how the beads are fusing. Depending on the size of the project, additional heating time may be required. DO NOT OVER-IRON the beads as it will make the centers of the beads close and can make the assembly you do with your project more challenging.
Fusing Instructions—Only Adults Iron
MagentaRaspberry Pearl Stripe
OrangeZebra Stripe
PlumGrape Stripe
Kiwi LimePrickly Pear Pearl Stripe
PurpleStarry Nite Stripe
TurquoiseRoyal Blue Pearl Stripe
BlackFire Stripe
Prickly PearCucumber Stripe
WhiteSilver Pearl Stripe
MAKE 9
Tombstone Ring Toss
10 www.eksuccessbrands.comPerler Beads and EKSuccess Brands are either registered trademarks or trademarks of Dimensions Crafts LLC and EK Success Ltd. respectively in the United States and/or other countries. © 2014 Dimensions Crafts LLC. All rights reserved.
1
2
Assemble the tombstones and gates by inserting the upright portion into the base. For the skull tombstone, also insert the candles into each base. For the small tombstones with the cross, insert the zombie hands into each base.
On the tree monster, glue each of the arms to the trunk as indicated by the pink dots on the diagram.
Insert the trunk into the base as shown.
ASSEMBLY