Research ArticleAnalysis of the Single Toggle Jaw Crusher ForceTransmission Characteristics
Moses Frank Oduori, David Masinde Munyasi, and Stephen Mwenje Mutuli
Department of Mechanical and Manufacturing Engineering, The University of Nairobi, P.O. Box 30197, Nairobi 00100, Kenya
Correspondence should be addressed to Moses Frank Oduori; [email protected]
Received 9 June 2016; Revised 6 November 2016; Accepted 14 November 2016
Academic Editor: Yuh-Shyan Hwang
Copyright Β© 2016 Moses Frank Oduori et al. This is an open access article distributed under the Creative Commons AttributionLicense, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properlycited.
This paper sets out to perform a static force analysis of the single toggle jaw crushermechanism and to obtain the force transmissioncharacteristics of the mechanism. In order to obtain force transmission metrics that are characteristic of the structure of themechanism, such influences as friction, dead weight, and inertia are considered to be extraneous and neglected. Equations areobtained by considering the balance of forces at themoving joints and appropriately relating these to the input torque and the outputtorque. A mechanical advantage, the corresponding transmitted torque, and the variations thereof, during the cycle of motion ofthe mechanism, are obtained. The mechanical advantage that characterizes the mechanism is calculated as the mean value overthe active crushing stroke of the mechanism. The force transmission characteristics can be used as criteria for the comparison ofdifferent jaw crusher mechanism designs in order to select the most suitable design for a given application.The equations obtainedcan also be used in estimating the forces sustained by the components of the mechanism.
1. Introduction
The literature on kinematics andmechanism design identifiesthree tasks for which linkage mechanisms are commonlydesigned and used, namely, function generation, motiongeneration, which is also known as rigid body guidance, andpath generation [1β3]. Way back in 1955, Freudenstein, whois widely regarded as the father of modern Kinematics ofMechanisms andMachines, introduced an analytical methodfor the design of a four-bar planar mechanism for functiongeneration [4]. Wang et al. presented a study on the synthesisof planar linkagemechanisms for rigid body guidance [5]. Aninteresting design and application of a planar four-bar mech-anism for path generationwas reported by Soong andWu [6].In general, the use of linkage mechanisms involves the trans-mission and transformation of motions and forces. In prac-tical applications, linkage mechanisms appear to be morecommonly designed and used for the transmission and trans-formation of motions rather than forces. In such cases, thetransmitted forces are quite small.
The jaw crusher happens to be an example of a planarlinkage application that is designed andused for the transmis-sion and transformation of motions but also has to transmit,
transform, and apply the large forces that are required tocrush hard rocks by compression.Therefore it is important tounderstand the force transmission characteristics of the jawcrusher mechanism and to be able to use them for soundmechanical design of the crusher.
Today, the most commonly used types of jaw crusher arethe single toggle and the double toggle designs. The originaldouble toggle jaw crusher was designed by Eli Whitney Blakein the USA in 1857 [7].Themotion of the swing jaw in a dou-ble toggle crusher is such that it applies an almost purely com-pressive force upon the material being crushed. This mini-mizeswear on the crushing surfaces of the jaws andmakes thedouble toggle jaw crusher suitable for crushing highly abra-sive and very hard materials. Even today, the Blake design,with some comparatively minor improvements, can still befound in mines and quarries around the world.
The single toggle design, which was developed betweenthe 1920s and the 1950s, is a simpler, lighter crusher [7]. Itsswing jaw has a rolling elliptical motion such that it applies acompressive as well as a rubbing force on the material beingcrushed. This has a force-feeding effect that improves thethroughput of the device, but it also tends to cause rapid wear
Hindawi Publishing CorporationJournal of EngineeringVolume 2016, Article ID 1578342, 9 pageshttp://dx.doi.org/10.1155/2016/1578342
2 Journal of Engineering
of the crushing surfaces of the jaws. However, the single tog-gle jaw crusher has a lower installed cost, as compared to thedouble toggle design. Improvements in materials and designhave made the single toggle jaw crusher more common todayas the primary crusher in quarrying operations [8]. Accord-ing to Carter Russell [9], in 1999 sales of the single toggle jawcrusher exceeded those of the double toggle jaw crusher by afactor of at least nine to one.
This paper performs a static force analysis of the singletoggle jaw crusher mechanism. As a result of this analysis, acharacteristic force transmission ratio, which may be regar-ded as a mechanical advantage of the mechanism, is derived.This ratio can be used as a criterion for the comparisonof different jaw crusher mechanism designs, with a view toselecting the most suitable design for use in a given applica-tion.
2. Literature Review
Over time, several authors have addressed the static forceanalysis of the double toggle jaw crusher mechanism. Amongthe earlier of such efforts is that of Ham et al. [10], whoperformed a static force analysis of the double toggle jawcrusher mechanism in order to determine the input turningmoment that would be required to overcome a knowncrushing resistance of the material being crushed. They useda graphical method to carry out the analysis.
In discussing linkages, Martin [11] featured the doubletoggle jaw crusher mechanism as an example of a machinethat uses the toggle effect to obtain a large output force thatacts through a short distance, but he did not perform a staticforce analysis of the mechanism.
Erdman and Sandor [1] presented the determination ofthe mechanical advantage of a double toggle jaw crushermechanism, as an exercise problem to be solved by
(1) the method of instant centres, which is essentially agraphical method;
(2) an analytical method that utilized complex numberrepresentation of vectors.
Norton [2] also discussed the mechanical advantage oflinkagemechanisms and explained the toggle effect by the useof a jaw crusher mechanism of the Dodge type [8].
More generally, Lin and Chang [12] addressed the issueof force transmissivity in planar linkage mechanisms. Theyderived and proposed a force transmissivity index (FTI) thatconsidered the power flow path from the input linkage tothe output linkage. They calculated the effective force ratio(EFR) as the ratio of the sum of actual power transmitted ateach of the linkage joints in the power flow path to the sumof the maximum possible power that could be transmittedalong the same power flow path. They then obtained the FTIas the product of the EFR and the mechanical advantage ofthe mechanism, thus taking into account the effect of theexternal load acting on the mechanism.They compared theirresults to other indices of force transmissivity, such as theJacobian matrix method [13] and the joint force index (JFI)[14], and found their FTI to be more accurate. Furthermore,
the Jacobian matrix method does not consider the effect ofthe external load while the JFI does not consider the powerflow path in the mechanism.
The method used by Lin and Chang [12] involves a staticforce analysis and the determination of velocities at the jointswithin the power flow path. Subsequently, Chang et al. [15]extended and applied this method to parallel manipulators,defined, and proposed a mean force transmission index(MFTI). The presentation here will perform a static forceanalysis and obtain the mechanical advantage of the singletoggle jaw crusher mechanism, from first principles.
3. Methodology
According toHamet al. [10], analysis of forces in anymachineis based on the fundamental principle which states that βthesystem composed of all external forces and all the inertiaforces that act upon any given member of the machine is asystem that is in equilibrium.β
For a planar mechanism, such as the single toggle jawcrusher, it is customary to treat the forces as if they arecoplanar, at least in the initial analysis. The effects of theoffsets between the planes of action of the forces can then berevisited at a later stage of analysis and design. The assump-tion of coplanar forces will be employed in this presentation.
In the static force analysis of a machine, the forcesarising due to the accelerations of the machine members areneglected. These forces are taken into account in a dynamicforce analysis, which can be done, meaningfully, after theforms and masses of the machine members have been deter-mined. Frictional forces may be taken into account in a staticforce analysis [16], but in the present case, it shall be assumedthat the use of antifriction bearings in the revolute jointsreduces frictional forces to negligible levels.
Furthermore, this presentation aims to obtain an indica-tor of the efficacy of force transmission, in the single togglejaw crusher, that may be attributed to the structure of themechanism per se. Therefore, frictional and inertia forcesmay be regarded as extraneous to this purpose and will notbe included in this analysis.
In a planar four-bar mechanism with four revolute joints,which can be denoted by π π π π or 4π , the efficacy of forcetransmission has often been expressed by what is known asthe transmission angle [2, 3, 11, 17]. This works well enoughif, for instance, the mechanism is a crank-and-rocker, inwhich the crank is the input link and the rocker is the outputlink. Then, the transmission angle becomes the acute anglebetween the rocker and the coupler, and, indeed, its valueindicates the efficacy of force transmission in themechanism.
The single toggle jaw crushermechanism can bemodelledas a planar 4π mechanism, as shown in Figure 1. However, inthismechanism, it is the coupler that is the output link and thetransmission angle, as defined in the above cited literature,fails to be a suitable indicator of the efficacy of force trans-mission. Therefore, a better indicator of the efficacy of forcetransmission in the single toggle jaw crusher is sought in thispaper.
Journal of Engineering 3
Y
Z
Fixed jaw
r1
r2
r3
r4
π1
π2
π3
π4
O1
O2
O3
O4
Figure 1: Kinematical model of the single toggle jaw crusher.
Erdman and Sandor [1], Norton [2], and Shigley and Uic-ker Jr. [3] presentedmethods for determining the mechanicaladvantage of planar 4π mechanisms that make the assump-tion of 100% mechanical efficiency for the mechanism andfind the mechanical advantage of the mechanism to beinversely proportional to the output-to-input angular velocityratio. The presentation by Shigley and Uicker Jr. [3] definedthe mechanical advantage as the ratio of the output torque tothe input torque, which led to a slightly different expressionfor the mechanical advantage, as compared to Erdman andSandor [1] and Norton [2], who defined mechanical advan-tage as the ratio of output force to input force.
The methods presented by Erdman and Sandor [1],Norton [2], and Shigley and Uicker Jr. [3] give no indicationof the actual forces that are sustained by the members of themechanism, knowledge of which would be necessary at thedesign stage.
The method used in this paper includes the following:
(i) A static force analysis that neglects the frictional andinertia forces is performed.
(ii) All the forces and moments are assumed to be cop-lanar.
(iii) The analysis proceeds by considering the equilibriumof the forces acting at the moving joints of the mecha-nism and relating them to the input torque as well as
the load torque.This may be compared to the methodpresented by Abhary [18].
The method used here is systematic and therefore clear andsimple to follow and to use. As a result of the analysis, acharacteristic mechanical advantage of the single toggle jawcrusher mechanism is obtained, which may be used as acriterion for selecting such mechanisms.
4. A Review of the Single Toggle JawCrusher Kinematics
In the kinematical model of the single toggle jaw crusher,which is illustrated in Figure 1, the eccentric shaft is modelledas a short crank, of length π2, that continuously rotates about afixed axis, atπ2.The swing jaw ismodelled as the coupler linkπ3π4, of length π3, which moves with a complex planarmotion that has both rotational and translational compo-nents. The toggle link is modelled as the rocker π4π1,which oscillates about the fixed axis at π1. The fixed jaw isconsidered to be an integral part of the frame of the machine.
Oduori et al. [19] analysed the kinematics of the singletoggle jaw crusher, as modelled in Figure 1, and found thefollowing expression:2π1π2 cos (π2 β π1) + 2π2π3 cos (π3 β π2)+ 2π3π1 cos (π3 β π1) = π42 β π32 β π22 β π12. (1)
4 Journal of Engineering
Table 1: Data for a PE 400 by 600 single toggle jaw crusher (mm).
π1 sin π1 π1 cos π1 π2 π3 π445.3 815.7 12 1085 455
Cao et al. [20] used the dimensional data for a PE 400 Γ 600single toggle jaw crusher, as shown in Table 1.
From the data in Table 1, it follows, to good approxima-tion, that π1 = 817mm and π1 = 3.18β. We shall adopt thesedata as we proceed.
By substituting the data given in Table 1, into equation (1),the following is obtained:
0.753 cos (π2 β 3.18β) + cos (π3 β π2)+ 68.08 cos (π3 β 3.18β) = β62.894. (2)
Equation (2) can be used to determine values of π3 for anygiven value of π2, which represents the input motion.
In the cycle of motion of the single toggle jaw crushermechanism, two phases, known as the toggle phases, are ofparticular interest. In each of the toggle phases, the crank andthe coupler link fall on a single straight line. Therefore, thetoggle phases occur when π2 = π3 and when π2 = π3 + 180β.For the first toggle phase, equation (2) can be reduced to thefollowing:
68.833 cos (π2 β 3.18β) = β63.894. (3)
Equation (3) is readily solved to give π2 = 161.34β for the firsttoggle phase.
Similarly, for the second toggle phase, equation (2) can bereduced to the following:
67.327 cos (π2 β 3.18β) = 61.894. (4)
Equation (4) too is readily solved to give π2 = 340β for thesecond toggle phase.
5. Force Transmission Model
The forces and moments acting upon the links of the singletoggle jaw crusher mechanism are all assumed to be coplanarand illustrated in Figure 2.
In performing the static force analysis it shall be assumedthat the masses of the links, as well as friction forces, arenegligible. The effects of these forces can be considered ata later stage in the design of the mechanism. In Figure 2,π2 is the driving torque, applied at the crank axis π2, todrive the crank and the entire crusher mechanism. π3 is thetorque, acting about the axis of jointπ3, due to the resistanceof the feed material against being crushed. πΉ2, πΉ3, and πΉ4are the forces in links 2, 3, and 4, respectively, and they areall assumed to be compressive. The system of forces andmoments is assumed to be in equilibrium in every phase ofmotion of the mechanism.
6. Static Force Analysis
The forces acting at the moving joints π3 and π4 are shownin Figure 3.
Let us start by considering the crank. Static force analysisis based on the assumption that there are no accelerationsin the mechanism. Referring to Figures 1, 2, and 3, theequilibrium of moments acting on the crank, about the fixedjoint π2, leads to the following result:
0 = βπΉπ32π2 sin π2 β πΉπ32π2 cos π2 + π2,π2 = [πΉπ32 cos π2 + πΉπ32 sin π2] π2. (5)
Next let us consider the coupler. The equilibrium of forces atjoint π3 leads to the following:πΉπ23 + πΉ3 cos (180β β π3) = 0,
πΉπ23 = πΉ3 cos π3,πΉπ32 = βπΉπ23 = βπΉ3 cos π3,
πΉπ23 + πΉ3 sin (180β β π3) = 0,πΉπ23 = βπΉ3 sin π3,πΉπ32 = βπΉπ23 = πΉ3 sin π3.
(6)
From equations (5) and (6), it follows that
π2 = (πΉ3 sin π3 cos π2 β πΉ3 cos π3 sin π2) π2= πΉ3π2 sin (π3 β π2) . (7)
The statement in equation (7) is illustrated in Figure 4.Moreover, it should be evident from Figures 3 and 4 that
πΉ3 cos (π3 β π2) = βπΉ2. (8)
Now, in Figure 3, by considering the equilibrium of all theforces acting upon the coupler, the following is obtained:
πΉπ43 + πΉπ23 = 0,πΉπ43 = βπΉπ23 = βπΉ3 cos π3,
πΉπ43 + πΉπ23 = 0,πΉπ43 = βπΉπ23 = πΉ3 sin π3.
(9)
Moreover, in Figure 3, the equilibrium of moments acting onthe coupler, about the joint π3, leads to the following result:
0 = βπΉπ43π3 sin π3 + πΉπ43π3 cos π3 + π3,π3 = [πΉπ43 sin π3 β πΉπ43 cos π3] π3. (10)
From equations (9) and (10), it follows that
π3 = βπΉ3π3 sin (2π3) . (11)
A relationship between π3 and π2 can now be obtained fromequations (7) and (11), as follows:
π (π2) = π3π2π2π3 = βsin (2π3)
sin (π3 β π2) . (12)
Journal of Engineering 5
O2
F2
F2
F3
F3F4
F4
T2
T3
O3
O4
O1
Figure 2: Model for static force analysis of the single toggle jaw crusher.
Equation (12) is in dimensionless form. The left-hand side ofthis equation can be regarded as a force transmission ratiothat compares the nominal transmitted force, π3/π3, to thenominal input force, π2/π2. This ratio is an indicator of thetheoretical force transmission potential for any given phaseof motion of the mechanism.
For a given crusher mechanism, the values of π2 and π3can be determined from purely kinematical considerations,by the use of (1) along with the dimensional data of themechanism, and then the value of the right-hand side of (12)will be determined.
Using the dimensional data of the mechanism, given inTable 1, along with given values of π2, the correspondingvalues of π3were computed and thenused in (12) to determinethe corresponding force transmission ratios, for one and ahalf cycles of motion of the crank. The results are plotted inFigure 5.
The first spike in Figure 5 indicates the great amplificationof the crushing force that occurs at the first toggle position,which corresponds to a crank angle of about 161.34β. Theo-retically, the crushing force amplification should be infinite atthis toggle phase. Moreover, there occurs an abrupt reversalof the sign of the force transmission ratio from positive tonegative, at this toggle phase. The second spike in Figure 5,which is also accompanied by a reversal in the sign of theforce transmission ratio, occurs at a crank angle of about
340β.This spike corresponds to the second toggle phase of themechanism.
The great amplification of transmitted force, accompa-nied by the abrupt reversal of the sign of the force trans-mission ratio, at each of the toggle phases, may be comparedwith the phenomenonof resonance, inmechanical vibrations,which also features great amplification of the respondingmotion, accompanied by a reversal of the phase between theforcing and the responding functions.
As the crank rotates from π2 = 161.34β to π2 = 340β,the crusher would be on the idle stroke with the swing jawbeing retracted and no work being done in crushing the feedmaterial. This is evidenced by the negative values of the forcetransmission ratio, between these two angular positions of thecrank, in Figure 5. Useful work is done as the crank rotatesfrom π2 = 340β to π2 = 521.34β, in a succeeding cycle ofmotion of the crank.Thus, during each cycle of motion of thecrank, the useful working stroke of the mechanism lasts forabout 181.34β of rotation of the crank, which is very slightlygreater than half the cycle of motion of the crank. On theother hand, during each cycle of motion of the crank, the idlestroke lasts for 178.66β of rotation of the crank, which is veryslightly less than half the cycle of motion of the crank.
Thus, the mechanism has a quick return feature that ishardly noticeable since the crushing stroke lasts for 50.37% ofthe complete cycle of its motion, while the idle stroke lasts for49.63%of the complete cycle of themotion of themechanism.
6 Journal of Engineering
(2) Crank
(4) Rocker
(3) Coupler
O2
O3
O4
O4
O1
O3
FY23
FY32
FY43
FZ43
FZ23FZ32
FZ34
FY34
T3
T2
F3
F3
Figure 3: Free-body diagrams of the crank, the coupler, and the rocker.
(2) Crank
O2
O1T2
F3r2
(π3 β π2)
Figure 4: Balance of moments on the crank.
7. Results and Discussion
7.1. Force Transmission Ratio and the Transmitted Torque. Inthe preceding section, we have seen that the crushing strokelasts for only about 50% of each complete cycle of motionof the single toggle jaw crusher. For the other 50% of the
0
5
10
15
20
45 90 135 225 270 360 405 450 495
Angular position of the crank (degrees)Forc
e tra
nsm
issio
n ra
tio (d
imen
sionl
ess)
β5
β10
β15
β20
0 540315180
Figure 5: Variation of force transmission ratio with crank angle π2.
complete cycle of motion, the swing jaw is being retracted inpreparation for the next crushing stroke.
Moreover, in Figure 5, it can be seen that the force trans-mission ratio varies from a very high value, at the beginningof the crushing stroke, that initially falls very rapidly and thenlevels off to reach a minimum value of less that unity (about
Journal of Engineering 7
Table 2: Sample values of force transmission ratio during the crush-ing stroke.
π2 (degrees) Force transmission ratio, π(π2) (dimensionless)340 2,418.327350 4.649360 1.882370 1.280380 0.989390 0.823400 0.772410 0.660420 0.624430 0.609440 0.612450 0.636460 0.684470 0.766480 0.904490 1.148500 1.642510 3.046520 26.030521.31 3,268.45
0.6), about halfway through the crushing stroke. The latterhalf of the crushing stroke appears to be a mirror image ofthe earlier half, inwhich the force transmission ratio first risesgradually and then spikes to a very high value at the end of thecrushing stroke. Sample values of the force transmission ratioduring the useful crushing stroke are given in Table 2.
The fact that the crushing stroke commences with a veryhigh value of the force transmission ratio is advantageouswhen crushing brittle material, which is often the case. Sincebrittle materials fracture without undergoing significantdeformation, actual crushing of brittle materials in a singletoggle jaw crusher would occur soon after commencementof the crushing stroke, where the force transmission ratio ishigh.
According to Chinese jaw crusher manufacturerβs data[21], the PE 400 by 600 single toggle jaw crusher has 30 kWmotor power and an input eccentric shaft speed of 275 rpm or28.7979 radians per second. Assuming that the input speed isconstant, the input torque is found to be 1.0417 kNm. By usingthis information, along with the data in Table 1 and (12), thetransmitted torque, in kilonewton-metres, can be estimatedto be the following:
π3 = β94.19 [ sin (2π3)sin (π3 β π2)] . (13)
The above calculation assumes a 100% power transmissionefficiency. Equation (13) was used to calculate the values ofthe transmitted torque that are given in Table 3.
The above calculations reveal that the minimum valueof the transmitted torque will be about 55 times as big asthe input torque, with the theoretical maximum value being
Table 3: Sample values of the transmitted torque during the crush-ing stroke.
π2 (degrees) Transmitted torque, π3 (kilonewton-metres)340 227,784.124350 350.770360 196.420370 120.544380 93.110390 77.544400 68.000410 62.120420 58.741430 57.325440 57.685450 59.917460 64.441470 72.195480 85.183490 108.106500 154.632510 286.930520 2451.743521.31 307,857.521
0
500
1000
1500
2000
340 370 400 430 460 490 520
Angular position of the crank (degrees)
Tran
smitt
ed to
rque
(kilo
new
ton-
met
res)
Figure 6: Variation of transmitted torque during a crushing stroke.
infinity.This is why amaterial that cannot be crushedwill leadto breakage of the toggle link.
The values of the transmitted torque, as calculated by theuse of (13), are plotted in Figure 6, for one complete activecrushing stroke.
7.2. Characteristic Mechanical Advantage. A force transmis-sion ratio that would characterize the single toggle jaw cru-sher was calculated as the mean value of the force transmis-sion ratio over a complete useful crushing stroke, which doesnot include the retraction stroke.
According to theMeanValueTheorem of the integral cal-culus [22], if a function π¦ = π(π₯) is continuous on the closed
8 Journal of Engineering
Table 4: Force transmission characteristics of the single toggle jaw crusher.
Characteristics Value (dimensionless) Corresponding crank angle (degrees)Minimum force transmission ratio 0.608 433Maximum force transmission ratio 3268.446 521.31Mean force transmission ratio 10.581 Nonapplicable
interval [π, π], then the mean value of π¦ for that interval canbe determined as follows:
π¦ = 1π β π β«π
π
π (π₯) dπ₯. (14)
In determining the characteristic mechanical advantage, themean value of the force transmission ratio was determined asfollows:
π (π2) = 1181.31β β«521.31
β
340β
sin (2π3)sin (π3 β π2)dπ2. (15)
The integral in (15) was evaluated numerically by the use ofthe composite trapezoidal rule [23]. For 340β β€ π2 β€ 520β,taken at one-degree intervals, the integral was evaluated asfollows:
πΌ1 = 12 [[π (340β) + 2π2=519
β
βπ2=341β
π (π2) + π (520β)]]= 1, 559.709.
(16)
For 520β β€ π2 β€ 521.31β, taken as three unequal intervals, theintegral was evaluated as follows:
πΌ2= [π (520β) + 1.3π (521β) + 0.31π (521.3β) + 0.01π (521.31β)2 ]= 358.8177.
(17)
In (16) and (17), π(340β), for instance, is the value of π(π2)for the case where π2 = 340β. The total integral was thendetermined as follows:
πΌ = πΌ1 + πΌ2 = 1, 918.527. (18)
Thus, the characteristic mechanical advantage was deter-mined as follows:
π (π2) = πΌ181.31β = 10.581. (19)
From the preceding analysis, the force transmission char-acteristics for the PE 400 by 600 single toggle jaw crushermechanism are summed up in Table 4.
The minimum force transmission ratio occurs at aboutthe midpoint of the active crushing stroke, while the maxi-mum force transmission ratio occurs at the end of the activecrushing stroke. However, the force transmission ratio at thebeginning of the active crushing stroke is also very highβabout 74% of the value at the end of the crushing stroke.
Given a number of different mechanism designs, thecharacteristics given in Table 4 may be calculated for eachcandidate mechanism and used, among others, as criterion inthe selection of a suitable jaw crusher mechanism for a givenapplication.
8. Conclusions
A static force analysis of the single toggle jaw crushermechanism was carried out. The method used is systematic,clear, and simple to follow and to use. As a result of thestatic force analysis, some force transmission characteristicsof the single toggle jaw crusher mechanism were obtained.The analysis can also be used to determine the forces thatare sustained by each of the components of the single togglejaw crusher mechanism, provided that the values of the inputtorque and load torque are known.
An expression for the force transmission ratio of thesingle toggle jaw crusher mechanism was derived. By usingthe dimensional data of the PE 400 by 600 jaw crusher, themaximum value of the force transmission ratio was found tobe about 3268, the minimum value of the force transmissionratio was found to be about 0.61, and the mean value of theforce transmission ratio was found to be about 10.6. Thesemetrics can be used as criteria in the selection of a suitablemechanism design to be used in a given application, out ofdifferent alternatives.
The force transmission ratio was found to be very highat the beginning of the active crushing stroke, dropped offrapidly and then levelled off at about the minimum value,remained at the low value for about two-thirds of the activecrushing stroke, and then rose rapidly to a very high value atthe end of the active crushing stroke. The fact that the forcetransmission ratio is very high at the beginning of the activestroke is advantageous in crushing brittle materials whichfracture without undergoing appreciable deformation.
Competing Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
References
[1] A. G. Erdman and G. N. Sandor, Mechanism Design: Analysisand Synthesis, vol. 1, Prentice-Hall, 1991.
[2] R. L. Norton, Design of Machinery: An Introduction to the Syn-thesis and Analysis of Mechanisms and Machines, McGraw-Hill,1992.
[3] J. E. Shigley and J. J. Uicker Jr.,Theory of Machines and Mecha-nisms, McGraw-Hill Book Company, 1980.
Journal of Engineering 9
[4] F. Freudenstein, βApproximate synthesis of four bar linkages,βTransactions of the ASME, vol. 77, pp. 853β861, 1955.
[5] Z. Wang, H. Yu, D. Tang, and J. Li, βStudy on rigid-bodyguidance synthesis of planar linkage,βMechanism and MachineTheory, vol. 37, no. 7, pp. 673β684, 2002.
[6] R.-C. Soong and S.-L. Wu, βDesign of variable coupler curvefour-barmechanisms,β Journal of the Chinese Society ofMechan-ical Engineers, vol. 30, no. 3, pp. 249β257, 2009.
[7] A. L. Mular, N. H. Doug, and D. J. Barrat, Mineral ProcessingPlant Design, Practice and Control: Proceedings, vol. 1, Societyfor Mining, Metallurgy and Exploration, 2002.
[8] The Institute of Quarrying Australia, Technical Briefing PaperNo. 6: Crusher Selection III, https://www.quarry.com.au/files/technical papers/microsoft word - technical paper-no.6.doc.pdf.
[9] A. Carter Russell, βNew Jaw Crushers are Reliable, Affordableand Transportable,β Rock Products, 1999, http://www.rockpro-ducts.com/index.php/features/51-archives/1240.pdf.
[10] C. W. Ham, E. J. Crane, and W. L. Rogers,Mechanics of Machi-nery, McGraw-Hill Book Company, 4th edition, 1958.
[11] G. H. Martin, Kinematics and Dynamics of Machines, McGraw-Hill, 2nd edition, 1982.
[12] C.-C. Lin and W.-T. Chang, βThe force transmissivity index ofplanar linkage mechanisms,β Mechanism and Machine Theory,vol. 37, no. 12, pp. 1465β1485, 2002.
[13] J. Denavit, R. S. Hartenberg, R. Razi, and J. J. Uicker, βVelocity,acceleration, and static-force analyses of spatial linkages,β Jour-nal of Applied Mechanics, vol. 32, no. 4, pp. 903β910, 1965.
[14] J. E. Holte and T. R. Chase, βA force transmission indexfor planar linkage mechanisms,β in Proceedings of the ASMEMechanisms Conference, pp. 377β386, 1994.
[15] W.-T.Chang,C.-C. Lin, and J.-J. Lee, βForce transmissibility per-formance of parallel manipulators,β Journal of Robotic Systems,vol. 20, no. 11, pp. 659β670, 2003.
[16] K. Abhary, βA simple analytical method for force analysis ofplanar frictional tree-like mechanisms,β in Proceedings of theASEE Annual Conference and Exposition, Pittsburgh, Pa, USA,2008.
[17] J. T. Kimbrell, Kinematics Analysis and Synthesis, McGraw-Hill,1991.
[18] K. Abhary, βA simple analytical method for teaching force ana-lysis of planar frictionless mechanisms,β in Proceedings of theASME International Mechanical Engineering Congress and Exp-osition (IMECE β05), pp. 41β48, Orlando, Fla, USA, November2005.
[19] M. F. Oduori, S. M. Mutuli, and D. M. Munyasi, βAnalysis ofthe single toggle jaw crusher kinematics,β Journal of Engineering,Design and Technology, vol. 13, no. 2, pp. 213β239, 2015.
[20] J. Cao, X. Rong, and S. Yang, βJaw plate kinematical analysisfor single toggle jaw crusher design,β in Proceedings of the Inter-national Technology and Innovation Conference (ITIC β06), pp.62β66, Hangzhou, China, November 2006.
[21] Zhengzhou Dingsheng Engineering Technology CompanyLimited, DSMAC PE Series Jaw Crusher Brochure, 2012, http://www.dscrusher.com/pdf/Jaw-Crusher.pdf.
[22] R. E. Larson, R. P. Hostetler, and B. H. Edwards, Calculus withAnalytical Geometry, chapter 4,D.C.Heath andCompany, 1994.
[23] S. C. Chapra, Applied Numerical Methods with MATLAB forEngineers and Scientists, chapter 19, McGraw-Hill, 3rd edition,2012.
International Journal of
AerospaceEngineeringHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
RoboticsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Active and Passive Electronic Components
Control Scienceand Engineering
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
RotatingMachinery
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporation http://www.hindawi.com
Journal ofEngineeringVolume 2014
Submit your manuscripts athttp://www.hindawi.com
VLSI Design
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Shock and Vibration
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Civil EngineeringAdvances in
Acoustics and VibrationAdvances in
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Electrical and Computer Engineering
Journal of
Advances inOptoElectronics
Hindawi Publishing Corporation http://www.hindawi.com
Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
SensorsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Modelling & Simulation in EngineeringHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Chemical EngineeringInternational Journal of Antennas and
Propagation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Navigation and Observation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
DistributedSensor Networks
International Journal of