R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
General Procedure for Laser Route Adjustment Regulate test power to below 50%, to keep the power not too high.
The first step: Adjust the laser route between laser beam spot and
the first reflecting mirror.
Put the test paper in front of the first reflecting mirror, then press "Laser" on the control panel slightly( loose immediately after pressing slightly you can see the spot on the test paper), then check if there is a spot in the centre of the first reflecting mirror, If in the center, you have finished the first step. If there is not or the spot is not in the center, please adjust the location or the height of the first reflecting mirror holder (or the laser tube). Please see below:
1) Put the test paper in front of the first reflecting mirror
2) press "Laser" key on the control panel
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
3) check if the spot is in the center of the mirror This is the first step, please make sure the spot is in the center.
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
The second step: Adjust the laser route between the first and the second reflecting mirror. First of all, put the test paper in front of the second reflecting mirror, using
direction keys on the control panel to move the track to the top left corner,
press "laser"and check if the spot on the test paper. Then move the track to
the lower left corner, press "laser" again, then please check whether the two
spots(the top left corner and lower left corner) are coincide with each other.
If the two spots coincide woith each other and near to the center of the mirror,
it shows optical path between the first reflecting mirror and the second
mirror is correct; if not, please adjust the screws on the back of the first reflecting
mirror holder to make sure the spots coincide with each other, then
adjust the location of second mirror holder (the X-axis direction), to make
sure the light reflected by first reflecting mirror hit on the second reflecting mirror.
Please see below: 1) put the test paper in front of the second reflecting mirror
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
2) press the arrows on the control panel to move the track to the top left corner,
press "laser" and make sure the spot is on the test paper
3) press "down" arrow to move the track to the lower left corner, press "laser" again
and make sure the second spot coincide with the first one.
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
4) If the spots are not in the same position, please adjust the screws on the back
of the first reflecting mirror holder;If the pots are not in the circle, please adjust
the position/height of the first reflecting mirror holder.
The third step: Adjust the laser route between the second and the
third reflecting mirror.
First, move the laser head to the left of the X axis, put the test paper in front of the
hole of the laser head, press "laser"slightly and there is a spot on the paper. Then,
move the laser head to the right of the X axis, press "laser" again, and check whether
the two spots coincide with each other, if coincide and the two spots are within
the hole of the laser head, the optical path is correct. If not,please adjust the screws
on the second mirror holderto reach above standard(Attention:the principle of
optical path adjustment is the same between mirror 1 and 2, 2 and 3). Then adjust
the location of second mirror holder (Y-axis direction) and the height of the laser tube,
to make sure the spots are within the hole of laser head (center is better). Please see
below:
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
1) Move the laser head to the left of the X axis , put the test paper in front of the
hole of the laser head.
2)Press "laser" and there will be a spot on the test paper
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
3) Move laser head to the right of the X axis, press "laser" again, and check
whether the two spots coincide with each other, please make sure they are
coincide and in the center of the hole.
4)If not, please adjust the screws on the second mirror holder to make sure the
spots are coincide; if the spots are not in the hole, adjust the location of second
mirror holder (the Y-axis direction), to make sure the spots are within the hole of
laser head(center is better).
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
The fourth Step: Adjust the laser route between the third reflecting mirror and the focus lens. Attach a test paper under the laser head or on the working platform, press "laser",
and check whether the spot is in the center. If so, optical path is correct; if not,
please adjust the screws on the laser head to make sure the spot is in the center.
Please see below:
1) Attach a test paper under the laser head, then press "laser", and check if the spot
is in the center.
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
2) If the spot is not in the center, please adjust the screws on the laser head.
We should make sure this spot below the laser head center, just as the picture
shows
R e d sa i l Te ch n o l o gy C o . , L t d Add: B218/F2,Qilu Software Plaza No.1 Shunhua Road,Jinan Hi-tech
Zone,Shandong,China ZIP: 250101 Tel: +86-531-86516855/56/57 Fax: +86-531-86516858
Email: [email protected]
http://www.redsailcutters.com
The fifth step: laser processing
After adjusting optical path and measuring focal length with focusing plate,
then you can process objects. Please see Picture Below:
Attention
1. Laser route adjustment is the adjustment of the angle between the mirror and
the laser route(it should be 45 degree). Some related knowledge are needed,
such as reflection principle. For beginners, please operate under the instruction,
consult the technician if necessary. In addition, laser is sightless and may
burn person, be careful when adjusting.
2. Generally, when adjusting, if the spots slant to one direction, set up the mirror
of the opposite direction or set down the mirror of the same direction, and
adjust the screws behind the mirror holder accordingly.
3. It is better to make sure the three reflecting mirrors are at the same horizontal
surface first, and it is more easier to adjust the laser beam.