Download - REAR WAI L TEMPLATE - Appliance Parts
NOTE: IT IS VERY IMPORTANT TOREAD AND FOLLOW THE DIRECTIONSIN THE INSTALLATION INSTRUCTIONSBEFORE PROCEEDING WITH THISREAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottommounting plate and to locate the horizontal exhaustoutlet.
1. Use a level to check that the template is positionedaccurately.
2. Locate and mark at least one stud on the left orright side of the centerline.
NOTE: It is important to use at least one woodscrew mounted firmly in a stud to support the weightof the microwave. Mark two additional, evenly spacedlocations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there isa stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes fortoggle bolts.
NOTE: DO NOT INSTALL THE MOUNTING PLATEAT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for yourinstallation situation.
i
i
i
Darle vuelta a la hoja para consultar la
vers=on en Espa o1.
iii
iii
iiii
!ii
!
!iii
|iii
|iii
|iii
I
Locate and mark holes to align with holes in themounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OFTHE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLYSPACED TOGGLE BOLTS IN THE MOUNTING PLATEAREA.
IIi
!_Jl Trim the rear wall template along the dotted line.dii
!ii
!ii
ii
Iii
Iii
iii
iPrinted in Malaysia
i DE68-03142Bii
i
A
iI
II
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILLDISCHARGE INTO HOUSE STRUCTURE.
I
Trim the rear wall template along the dotted line.
30" MINIMUM WIDTH REQUIREDI
iiii
REAR WAI L TEMPLATE
0 0 0 0 0 0 0 0 0 0 00 00 0 0 0 0
C
I
I
Ii
0i
Locate and mark holes to align with holes in themounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OFTHE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLYSPACED TOGGLE BOLTS IN THE MOUNTING PLATEAREA.
B
0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0
0
|iii
Iiii
|iii
Iiii
ii
ii
4!iiii
Iii
Iii
ii
iiii
iii
iii
!ii
i!iii
!iii
!iii
|iii
Iiii
|iii
|iii
tiii
ii
!ii
!ii
i
!Iii
II
iI
iI
ii
i ii ii
: NOTA: ES MUY IMPORTANTE LEER Y SEGUIR -- qLAS DIRECCIONES EN LAS INSTRUCCIONES DEINSTALACI6N ANTES DE PROCEDER CON ESTAPLANTILLA DE PARED POSTERIOR.Esta plantilla de la pared posterior sirve para colocar el plato demontaje inferior y para colocar la salida de escape horizontal.
1. Use un nivel para cerciorarse de que la plantilla est& colocada demanera apropiada.
2. Localice y marque por Io menos un bajante en el lado izquierdo oderecho de la linea central.
NOTA: Es importante usar por Io menos un tornillo de maderamontado firmemente en un bajante para soportar el peso delmicroondas. Marque dos lugares adicionales, espaciadosuniformemente, para los tornillos de palanca proporcionados.
3. Taladre agujeros en los lugares marcados. Donde exista unbajante, taladre agujeros de 3/16" para los tornillos de madera.Para los agujeros que no se alinean con el bajante, taladreagujeros de 5/8" para los tornillos de palanca.
NOTA: NO INSTALE EL PLATO DE MONTAJE EN ESTEMOMENTO.
Corte la plantillaubicadaen la paredde atr_sa trav_sde la linea de puntos
ii
!ii
iii
iii
ii
iiiii
!iii
!iii
!iii
|
4. Remueva la plantilla de la pared posterior.
5. Revise el Manual de instrucciones de instalaci6n para su situaci6nde instalaci6n.
Turn over for English,
iI
II
PRECAUCION - SI EL ADAPTADOR DE ESCAPE ESTb, COLOCADO MAS
ALLA DE LAS DIMENSIONES RECOMENDADAS, AIRE CARGADO CON
GRASA SE DESCARGARA HAClA LA ESTRUCTURA DE LA CASA.
i
iANCHO INIMO
iii
iii
iiii
!ii
!
!iii
|iii
|iii
|iii
I
IIi
PLANTILLA DELocaUcey marque los agujeros para que se allneen conlos agujeros en el plato de montaje.IMPORTANTE:
LOCAL.ICEPOR LO MENOS UN BAJANTE ENCUALQUIERA DE LOS LADOS DE LA LINEA CENTRAL.
MARQUE DOS LUGARESADICIONALES, ESPACIADOSUNIFORMEMENTE, PARA LOS TORNILLOS DE PALANCAEN EL AREA DEL PLATO DE MONTAJE.
!_ll Corte la plantilla ubicada en la pared de atr_s a tray,s de la linea de puntosdii
!ii
!ii
ii
Iii
Iii
iii
i Printed in Malaysia, DE68-03142Bi
iii
i
A
I
RED POSTERIORLo_llco y marque los agujeros para que se allneen conlos agujeros en el plato de montaje.IMPORTANTE:
LOCALICE POR LO MENOS UN BAJANTE ENCUALQUIERA DE LOS LADOS DE LA LINEA CENTRAL.
MARQUE DOS LUGARESADICIONALES, ESPACIADOSUNIFORMEMENTE, PARA LOS TORNILLOS DE PALANCAEN EL AREA DEL PLATO DE MONTAJE.
C
iii
iii
!iii
|iii
! 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0
I
I
( I
I
O' i
0 00 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0
|iii
Iiii
|iii
Iiii
ii
ii
4!iiii
Iii
Iii
ii
iiii
iii
iii
!ii
i
B
!iii
!iii
!iii
|iii
Iiii
|iii
|iii
tiii
ii
!ii
!ii
i
!
0
Iii
, IiI
iI
i0