Download - Q921 de2 lec2 v1
Drilling Engineering 2 Course (1st Ed.)
1. General Notes
2. Pore Pressure Prediction
3. Abnormal vs. normal Pressure
4. Fracture Gradient determination
Introduction
The knowledge of the formations to penetrate, their strength properties as well as their behaviour when in contact with various drilling fluids is essential to properly plan and complete a successful drilling project. Parameters like pore pressure and formation strength determine aspects like:Choice of mud weight profile,Determination of casing setting depths,Design of optimal casing strings,Selection of the drill bit,Cementing additives and procedures.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 4
pressures as gradients
The way how the formations react to drilling mud influences the selection of mud additives, borehole stability and therefore well control aspects.
Within drilling, it is common to express pressures as gradients. With this concept, the hydrostatic pressure can be given
as equivalent density which is independent of the depth and thus makes its comprehension and correlations of various concepts easier.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 5
reference depth
On the other hand, when gradients are applied, it has to be always kept in mind that they are referred to a specific depth. Knowing this reference depth is essential to compute
back the corresponding downhole pressures. Within drilling engineering, the drilling floor or rotary table
(RKB) is the most often used reference depth.
Geologists and geophysicists generally prefer to use their data in reference to ground floor or mean sea level (MSL).
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 6
Geology Prediction
Normally when a well is to be drilled, the drilling engineer is supplied from the geology department (or the geologist within the project team) with a sequence of predicted subsurface formations, their characteristics and markers, as well as knowledge about where special care has to be taken.
Geologists draw this information from studying the local geology (deposition history), seismic mappings (2D or 3D surveys) and perform well to well correlations (geological maps).
Whenever new information is gained (due to drilling and evaluation of a new well or further geophysical measurements) these maps are updated.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 7
Typical geological profile to plan a well
Typical geological profile Seismic record to determine the subsurface structure2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 8
local subsurface pressure regimes
To understand the local subsurface pressure regimes, the geologic processes along with the depositional history and tectonic abnormalities have to be studied.
When the well is located within shallow sediments that were laid down slowly within a deltaic depositional environment, the subsurface formation pressures can be assumed to be hydrostatic.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 10
Hydrostatic Pressure
By definition, a hydrostatic pressure is developed due to the own weight of a fluid at a certain depth. This relationship is expressed as: 𝑝 = 𝜌. 𝑔. ℎ = 9.81. 𝜌. ℎ
Or in field units:𝑝 = 0.052. 𝜌𝑓𝑙 . 𝐷
where:• 𝜌𝑓𝑙 [ppg] density of the fluid causing hydrostatic pressure
• 𝜌 [kg/m3] average fluid density• D [ft] depth at which hydrostatic pressure occurs (TVD)• h [m] vertical height of column of liquid• p [psi] hydrostatic pressure• g [m/s2] acceleration due to gravity
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 11
hydrostatically pressured formation
When the weight of the solid particles buried are supported by grain-to-grain contacts and the particles buried water has free hydraulic contact to the surface, the formation is considered as hydrostatically pressured.
As it can be seen, the formation pressure, when hydrostatically pressured, depends only on the density of the formation fluid (usually in the range of
1.00 [g/cm3] to 1.08 [g/cm3]) and
the depth in TVD.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 12
overburden stress
When the burial depth increases, the overlaying pressure (overburden stress) increases. This decreases the pore space
between the grains and thus the porosity of the formation.
The overburden stress can be calculated assuming an average bulk density b of the overlaying formations as:
Porosity profile2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 13
average bulk density
The average bulk density is normally found by integration of the density log readings.
When density logs were not run (e.g. at shallow formations), sonic log correlation methods,
together with lithology and mineralogical evaluations are applied to determine 𝜌𝑏
During burial of the sediments, formation water is constantly expelled due to the reduction of formation porosity, as see in next slide.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 14
Volume of fluid expelled during compaction of an argillaceous sediment
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 15
abnormally pressured
As long as formation water can be expelled, the formations are hydrostatic (or normally) pressured.
When drilling a well, formations are often encountered that are under a different pressure regime.These formations are named to be “abnormally
pressured”. Abnormal pressures can be positive
• (actual formation pressures are higher than hydrostatic pressure)
or negative “subnormal pressure”
• (actual formation pressures are lower than hydrostatic pressure).
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 16
Abnormally Mechanisms
Some mechanisms that lead to abnormally pressured formations are:1. Compaction effects,2. Aquathermal expansion,3. Diagenetic effects,4. Differential density effects (Osmosis),5. Fluid migration effects,6. Evaporite Deposits,7. Organic matter transformation,8. Tectonics,9. Connection to depleted reservoirs,10. Others.
From the various effects mentioned above, the compaction one is considered to be often the governing one.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 17
normally pressured formations
while burying of the sediments, formation water is expelled with increasing depth and temperatures due to reduction in pore space and diagenesis of the rock materials.
As long as the permeability and the effective porosity of the rock is high enough so that the formation water can escape as quickly as the natural compaction takes place, the formations are normally pressured.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 20
Modelling vertical Pressures
The (vertical) pressures acting inside formations can be modelled as: 𝜎𝑜𝑏 = 𝜎𝑧 + 𝑝where:
𝜎𝑜𝑏 [psi] overburden stress
𝜎𝑧 [psi] vertical stress supported by the grain-to-grain connections
p [psi] formation pore pressure
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 21
abnormally pressured formations
When the formation water can not escape as quickly as the pore space is reduced, it is trapped inside the formations. In this scenario, the increasing overburden stress will
pressurize the formation water and the formation will become abnormally pressured.
In this situation, the porosity of the formation will not follow the natural compaction trend (porosity at abnormally pressured formations will be higher than at normally pressured ones).
Along with the higher porosity, the bulk density as well as the formation resistivity will be lower at abnormally pressured formations.
These circumstances are often applied to detect and estimate the abnormal formation pressures.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 22
formation pore pressures
The actual measurement of formation pore pressure is very expensive and possible only after the formations have been drilled.In this respect, pore pressures have to be estimated
before drilling to properly plan the mud weights,
casing setting depths,
casing design, etc.
as well as being closely monitored during drilling.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 23
pore pressure estimation
To estimate the pore pressure and most important, define where abnormal pore pressures are to be expected, porosity logs and seismic measurements are applied most often.
shale formations tend to follow a defined porosity reduction trend with increasing depth. When this trend is interrupted, abnormally pressured
formations are to be expected. The knowledge of its depths are important since they may
lead to a necessary setting of casing and weighting up the mud system. The amount of how much the mud weight has to be increased
depends on the amount of abnormal pressure expected and the contingency of the well.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 24
Abnormal pressure detectionwhile drillingWhen the well is in progress
and abnormal formation pressures are expected, various parameters are observed and cross-plotted. Some of these while drilling detection methods are: (a) Penetration rate, (b) “d” exponent, (c) Sigmalog, (d) Various drilling rate
normalisations, (e) Torque measurements, (f) Overpull and drag, (g) Hole fill, (h) Pit level – differential flow
– pump pressure,
(i) Measurements while drilling,
(j) Mud gas, (k) Mud density, (l) Mud temperature, (m) Mud resistivity, (n) Lithology, (o) Shale density, (p) Shale factor (CEC), (q) Shape, size and
abundance of cuttings, (r) Cuttings gas, (s) X-ray diffraction, (t) Oil show analyzer, (u) Nuclear magnetic
resonance.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 25
Abnormal pressure evaluation
After an abnormal pressure is detected or the well is completed, various wireline log measurements are used to evaluate the amount of overpressures present. Among the most common ones are:(a) Resistivity, conductivity log,(b) Sonic log,(c) Density log,(d) Neutron porosity log,(e) Gamma ray, spectrometer,(f) Velocity survey or checkshot,(g) Vertical seismic profile.
With these log measurements trend lines are established and the amount the values deviate at the abnormally pressured formations from the trend line are applied to determine the value of overpressure.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 26
Schematic responses of wireline logs in an undercompacted zone
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 27
Leak-off data
Normally, after a casing is set and cemented, a so called leak-off test (LOT) is performed. The main issue of a LOT is to check the strength of the
formation at the casing shoe.
With this knowledge, the maximum kick pressure allowed that does not fracture the formation is determined.
It is also the key parameter in stress modelling and borehole integrity evaluation.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 29
formation integrity test
Sometimes the LOT test is not continued until leak-off (especially when oil based muds are used) and the formation is only pressured up until a certain value. This test is called formation integrity test (FIT).
In this way, when fracture strength is evaluated, it is important to distinguish LOT data and FIT data.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 30
fracture gradient
The pressure where fractures are initiated is commonly called leak-off pressure and when referred to the individual depth, named fracture gradient.
The determination of fracture gradients for shallow depth is often difficult since very little data exists. This is due to the circumstance that at shallow depth,
blowout preventers are often not installed and thus no pressure testing can be carried out.
Especially at offshore wells, the knowledge of shallow fracture gradients are important since the margin between pore pressure and fracture gradient is narrow and the danger of shallow gas pockets exists.
2013H. AlamiNia Drilling Engineering 2 Course: Geomechanics 31
1. Dipl.-Ing. Wolfgang F. Prassl. “Drilling Engineering.” Master of Petroleum Engineering. Curtin University of Technology, 2001. Chapter 3