Download - Product Guide REC670 1.2
Relion® 670 series
Bay control REC670CustomizedProduct Guide
Contents
1. Application...........................................................3
2. Available functions...............................................3
3. Differential protection.........................................13
4. Current protection..............................................13
5. Voltage protection..............................................16
6. Frequency protection.........................................16
7. Multipurpose protection.....................................17
8. Secondary system supervision..........................17
9. Control................................................................18
10. Scheme communication....................................20
11. Logic..................................................................22
12. Monitoring.........................................................23
13. Metering............................................................26
14. Basic IED functions...........................................26
15. Human machine interface.................................27
16. Station communication ....................................28
17. Remote communication....................................29
18. Hardware description........................................29
19. Connection diagrams........................................32
20. Technical data...................................................41
21. Ordering............................................................95
Disclaimer
The information in this document is subject to change without notice and should not be construed as a commitment by ABB AB. ABB AB assumesno responsibility for any errors that may appear in this document.
© Copyright 2011 ABB AB.
All rights reserved.
Trademarks
ABB and Relion are registered trademarks of ABB Group. All other brand or product names mentioned in this document may be trademarks orregistered trademarks of their respective holders.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
2 ABB
1. Application
REC670 is used for the control, protectionand monitoring of different types of bays inpower networks. The IED is especiallysuitable for applications in control systemswith distributed control IEDs in all bays withhigh demands on reliability. The IED can beused up to the highest voltage levels. It issuitable for the control of all apparatuses inany type of switchgear arrangements.
The control is performed from remote(SCADA/Station) through the communicationbus or from local HMI. Different controlconfigurations can be used, and one controlIED can be used per bay or one IED can becommon for several bays. Interlockingmodules are available for all common typesof switchgear arrangements. The control isbased on the select before execute principleto give highest possible security. Asynchronism control function is available tointerlock breaker closing. A synchronizingfunction where breaker closes at the rightinstance in asynchronous networks is alsoprovided.
A number of protection functions areavailable for flexibility in use for differentstation types and busbar arrangements. Theauto-reclose for single-, two-, and/or three-phase reclose includes priority circuits formulti-breaker arrangements. It co-operateswith the synchrocheck function with high-speed or delayed reclosing. Several breaker
failure functions are available to provide abreaker failure function independent fromthe protection IEDs, also for a complete one-and a half breaker diameter.
High set instantaneous phase and earthovercurrent, 4 step directional or non-directional delayed phase and earthovercurrent, thermal overload and two stepunder- and overvoltage functions areexamples of the available functions allowinguser to fulfill any application requirement.
REC670 has been provided with six ofovercurrent, earth fault, autorecloser andmeasuring functions. This, together with themulti-display local HMI allows use as multifeeder protection and controller fordistribution buses.
Disturbance recording and fault locator areavailable to allow independent post-faultanalysis after primary disturbances with asingle failure in the protection system.
6 x 32 dual directional channels for intertripand binary signals transfer is available oneach included communication card in thecommunication between selected IEDs insidethe station or in a near-by station.
The advanced logic capability, where the userlogic is prepared with a graphical tool, allowsspecial applications such as automaticopening of disconnectors in multi-breakerarrangements, closing of breaker rings, loadtransfer logics and so on. The graphicalconfiguration tool ensures simple and fasttesting and commissioning.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
Revision: B
ABB 3
2. Available functions
Main protection functions
2 = number of basic instances
0-3 = option quantities
IEC 61850 ANSI Function description Bay control
REC670
Differential protection
HZPDIF 87 1Ph high impedance differential protection 0-6
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
4 ABB
Back-up protection functions
IEC 61850 ANSI Function description Bay control
REC670
Current protection
PHPIOC 50 Instantaneous phase overcurrent protection 0-6
OC4PTOC 51_67 Four step phase overcurrent protection 0-6
EFPIOC 50N Instantaneous residual overcurrent protection 0-6
EF4PTOC 51N_67N
Four step residual overcurrent protection 0-6
NS4PTOC 46I2 Four step directional negative phase sequenceovercurrent protection
0-3
SDEPSDE 67N Sensitive directional residual overcurrent andpower protection
0-6
LPTTR 26 Thermal overload protection, one time constant 0-2
TRPTTR 49 Thermal overload protection, two time constant 0-2
CCRBRF 50BF Breaker failure protection 0-6
STBPTOC 50STB Stub protection 0-1
CCRPLD 52PD Pole discordance protection 0-3
GUPPDUP 37 Directional underpower protection 0-2
GOPPDOP 32 Directional overpower protection 0-2
BRCPTOC 46 Broken conductor check 0-1
CBPGAPC Capacitor bank protection 0-3
Voltage protection
UV2PTUV 27 Two step undervoltage protection 0-2
OV2PTOV 59 Two step overvoltage protection 0-2
ROV2PTOV 59N Two step residual overvoltage protection 0-2
VDCPTOV 60 Voltage differential protection 0-6
LOVPTUV 27 Loss of voltage check 0-2
Frequency protection
SAPTUF 81 Underfrequency protection 0-6
SAPTOP 81 Overfrequency protection 0-6
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 5
IEC 61850 ANSI Function description Bay control
REC670
SAPFRC 81 Rate-of-change frequency protection 0-6
Multipurpose protection
CVGAPC General current and voltage protection 0-9
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
6 ABB
Control and monitoring functions
IEC 61850 ANSI Function description Bay control
REC670
Control
SESRSYN 25 Synchrocheck, energizing check and synchronizing 0-6, 0-2
SMBRREC 79 Autorecloser 0-6, 0-4
APC8 3 Apparatus control for single bay, max 8apparatuses (1CB) incl. interlocking
1
APC15 3 Apparatus control for single bay, max 15apparatuses (2CBs) incl. interlocking
1
APC30 3 Apparatus control for up to 6 bays, max 30apparatuses (6CBs) incl. interlocking
1
QCBAY Apparatus control 1
LocalRemote
Handling of LRswitch positions 1
LocRemControl
LHMI control of PSTO 1
TR1ATCC 90 Automatic voltage control for tap changer, singlecontrol
0-4
TR8ATCC 90 Automatic voltage control for tap changer, parallelcontrol
0-4
TCMYLTC 84 Tap changer control and supervision, 6 binaryinputs
0-4
TCLYLTC 84 Tap changer control and supervision, 32 binaryinputs
0-4
SLGGIO Logic rotating switch for function selection andLHMI presentation
15
VSGGIO Selector mini switch 20
DPGGIO IEC61850 generic communication I/O functions 16
SPC8GGIO Single pole generic control 8 signals 5
AutomationBits
AutomationBits, command function for DNP3.0 3
Single command, 16 signals 4
VCTRSend Horizonal communication via GOOSE for VCTR 1
VCTRReceive
Horizontal communication via GOOSE for VCTR 7
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 7
IEC 61850 ANSI Function description Bay control
REC670
Secondary system supervision
CCSRDIF 87 Current circuit supervision 0-5
SDDRFUF Fuse failure supervision 0-4
Logic
SMPPTRC 94 Tripping logic 1-6
TMAGGIO Trip matrix logic 12
Configuration logic blocks 40-280
Configuration logic blocks Q/T 0-1
Extension logic package 0-1
Fixed signal function blocks 1
B16I Boolean 16 to Integer conversion 16
B16IFCVI Boolean 16 to Integer conversion with Logic Noderepresentation
16
IB16 Integer to Boolean 16 conversion 16
IB16FVCB Integer to Boolean 16 conversion with Logic Noderepresentation
16
Monitoring
CVMMXN Measurements 6
CNTGGIO Event counter 5
Event Event function 20
DRPRDRE Disturbance report 1
SPGGIO IEC61850 generic communication I/O functions 64
SP16GGIO IEC61850 generic communication I/O functions 16inputs
16
MVGGIO IEC61850 generic communication I/O functions 24
BSStartReport
Logical signal status report 3
RANGE_XP Measured value expander block 66
LMBRFLO Fault locator 0-1
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
8 ABB
IEC 61850 ANSI Function description Bay control
REC670
Metering
PCGGIO Pulse-counter logic 16
ETPMMTR Function for energy calculation and demandhandling
6
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 9
Designed to communicate
IEC 61850 ANSI Function description Bay control
REC670
Station communication
SPA communication protocol 1
LON communication protocol 1
IEC60870-5-103 communication protocol 20/1
Operation selection between SPA andIEC60870-5-103 for SLM
1
DNP3.0 for TCP/IP and EIA-485 communicationprotocol
1
DNP3.0 fault records for TCP/IP and EIA-485communication protocol
1
Redundant station bus communicationIEC61850-8-1, PRP
1
Parameter setting function for IEC61850 1
IntlReceive Horizontal communication via GOOSE forinterlocking
59
Goose binary receive 10
Multiple command and transmit 60/10
Ethernet configuration of links 1
DUODRV Duo driver configuration 0-1
Remote communication
Binary signal transfer receive/transmit 6/36
Transmission of analog data from LDCM 1
Receive binary status from remote LDCM 6/3/3
Scheme communication
ZCPSCH 85 Scheme communication logic for distance orovercurrent protection
0-1
ZCRWPSCH 85 Current reversal and weak-end infeed logic fordistance protection
0-1
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
10 ABB
IEC 61850 ANSI Function description Bay control
REC670
ZCLCPLAL Local acceleration logic 0-1
ECPSCH 85 Scheme communication logic for residualovercurrent protection
0-1
ECRWPSCH 85 Current reversal and weak-end infeed logic forresidual overcurrent protection
0-1
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 11
Basic IED functions
IEC 61850 Function description
Basic functions included in all products
IntErrorSig Self supervision with internal event list 1
TIME Time and synchronization error 1
TimeSynch Time synchronization 1
ActiveGroup Parameter setting groups 1
Test Test mode functionality 1
ChangeLock Change lock function 1
TerminalID IED identifiers 1
Productinfo Product information 1
MiscBaseCommon Misc Base Common 1
IEDRuntimeComp IED Runtime Comp 1
RatedFreq Rated system frequency 1
SMBI Signal Matrix for binary inputs 40
SMBO Signal Matrix for binary outputs 40
SMMI Signal Matrix for mA inputs 4
SMAI Signal Matrix for analog inputs 24
Sum3Ph Summation block 3 phase 12
LocalHMI Parameter setting function for HMI in PCM600 1
LocalHMI Local HMI signals 1
AuthStatus Authority status 1
AuthorityCheck Authority check 1
AccessFTP FTP access with password 1
SPACommMap SPA communication mapping 1
DOSFRNT Denial of service, frame rate control for front port 1
DOSOEMAB Denial of service, frame rate control for OEM port AB 1
DOSOEMCD Denial of service, frame rate control for OEM port CD 1
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
12 ABB
3. Differential protection
1Ph High impedance differentialprotection HZPDIF
The 1Ph High impedance differentialprotection (HZPDIF) function can be usedwhen the involved CT cores have the sameturns ratio and similar magnetizingcharacteristics. It utilizes an external CTcurrent summation by wiring, a seriesresistor, and a voltage dependent resistorwhich are mounted externally connected tothe IED.
HZPDIF can be used to protect tee-feeders orbusbars. Six single phase function blocks areavailable to allow application for two three-phase zones busbar protection.
4. Current protection
Instantaneous phase overcurrentprotection PHPIOC
The instantaneous three phase overcurrentfunction has a low transient overreach andshort tripping time to allow use as a high setshort-circuit protection function.
Four step phase overcurrentprotection OC4PTOC
The four step phase overcurrent protectionfunction OC4PTOC has an inverse or definitetime delay independent for step 1 and 4separately. Step 2 and 3 are always definitetime delayed.
All IEC and ANSI inverse time characteristicsare available together with an optional userdefined time characteristic.
The directional function is voltage polarizedwith memory. The function can be set to bedirectional or non-directional independentlyfor each of the steps.
A 2nd harmonic blocking can be setindividually for each step.
Instantaneous residual overcurrentprotection EFPIOC
The Instantaneous residual overcurrentprotection EFPIOC has a low transientoverreach and short tripping times to allowthe use for instantaneous earth-faultprotection, with the reach limited to less thanthe typical eighty percent of the line atminimum source impedance. EFPIOC can beconfigured to measure the residual currentfrom the three-phase current inputs or thecurrent from a separate current input.EFPIOC can be blocked by activating theinput BLOCK.
Four step residual overcurrentprotection EF4PTOC
The four step residual overcurrent protectionEF4PTOC has an inverse or definite timedelay independent for each step separately.
All IEC and ANSI time-delayed characteristicsare available together with an optional userdefined characteristic.
The directional function includes 3 options
• voltage polarized• current polarized• dual polarized
EF4PTOC can be set directional or non-directional independently for each of the steps.
Second harmonic blocking can be setindividually for each step.
EF4PTOC can be used as main protection forphase-to-earth faults.
EF4PTOC can also be used to provide asystem back-up for example, in the case ofthe primary protection being out of servicedue to communication or voltage transformercircuit failure.
Directional operation can be combinedtogether with corresponding communicationlogic in permissive or blocking teleprotectionscheme. Current reversal and weak-endinfeed functionality are available as well.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 13
EF4PTOC can be configured to measure theresidual current from the three-phase currentinputs or the current from a separate currentinput.
Four step negative sequenceovercurrent protection NS4PTOC
Four step negative sequence overcurrentprotection (NS4PTOC) has an inverse ordefinite time delay independent for each stepseparately.
All IEC and ANSI time delayed characteristicsare available together with an optional userdefined characteristic.
The directional function is voltage polarizedor dual polarized.
NS4PTOC can be set directional or non-directional independently for each of the steps.
NS4PTOC can be used as main protection forunsymmetrical fault; phase-phase shortcircuits, phase-phase-earth short circuits andsingle phase earth faults.
NS4PTOC can also be used to provide asystem back-up for example, in the case ofthe primary protection being out of servicedue to communication or voltage transformercircuit failure.
Directional operation can be combinedtogether with corresponding communicationlogic in permissive or blocking teleprotectionscheme. The same logic as for directionalzero sequence current can be used. Currentreversal and weak-end infeed functionalityare available.
Sensitive directional residualovercurrent and power protectionSDEPSDE
In isolated networks or in networks withhigh impedance earthing, the earth faultcurrent is significantly smaller than the shortcircuit currents. In addition to this, themagnitude of the fault current is almostindependent on the fault location in thenetwork. The protection can be selected touse either the residual current or residualpower component 3U0·3I0·cos j, for
operating quantity with maintained shortcircuit capacity. There is also available onenondirectional 3I0 step and one 3U0overvoltage tripping step.
Thermal overload protection, onetime constant LPTTR
The increasing utilizing of the power systemcloser to the thermal limits has generated aneed of a thermal overload protection alsofor power lines.
A thermal overload will often not be detectedby other protection functions and theintroduction of the thermal overloadprotection can allow the protected circuit tooperate closer to the thermal limits.
The three-phase current measuring protection
has an I2t characteristic with settable timeconstant and a thermal memory.
An alarm level gives early warning to allowoperators to take action well before the lineis tripped.
Thermal overload protection, twotime constant TRPTTR
If a power transformer or generator reachesvery high temperatures the equipment mightbe damaged. The insulation within thetransformer/generator will have forcedageing. As a consequence of this the risk ofinternal phase-to-phase or phase-to-earthfaults will increase. High temperature willdegrade the quality of the transformer/generator insulation.
The thermal overload protection estimatesthe internal heat content of the transformer/generator (temperature) continuously. Thisestimation is made by using a thermal modelof the transformer/generator with two timeconstants, which is based on currentmeasurement.
Two warning levels are available. Thisenables actions in the power system to bedone before dangerous temperatures arereached. If the temperature continues toincrease to the trip value, the protection
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
14 ABB
initiates a trip of the protected transformer/generator.
Breaker failure protection CCRBRF
Breaker failure protection (CCRBRF) ensuresfast back-up tripping of surrounding breakersin case the own breaker fails to open.CCRBRF can be current based, contact based,or an adaptive combination of these twoconditions.
Current check with extremely short reset timeis used as check criterion to achieve highsecurity against unnecessary operation.
Contact check criteria can be used where thefault current through the breaker is small.
CCRBRF can be single- or three-phaseinitiated to allow use with single phasetripping applications. For the three-phaseversion of CCRBRF the current criteria can beset to operate only if two out of four forexample, two phases or one phase plus theresidual current start. This gives a highersecurity to the back-up trip command.
CCRBRF function can be programmed to givea single- or three-phase re-trip of the ownbreaker to avoid unnecessary tripping ofsurrounding breakers at an incorrectinitiation due to mistakes during testing.
Stub protection STBPTOC
When a power line is taken out of service formaintenance and the line disconnector isopened in multi-breaker arrangements thevoltage transformers will mostly be outsideon the disconnected part. The primary linedistance protection will thus not be able tooperate and must be blocked.
The stub protection STBPTOC covers thezone between the current transformers andthe open disconnector. The three-phaseinstantaneous overcurrent function isreleased from a normally open, NO (b)auxiliary contact on the line disconnector.
Pole discordance protectionCCRPLD
An open phase can cause negative and zerosequence currents which cause thermal stresson rotating machines and can causeunwanted operation of zero sequence ornegative sequence current functions.
Normally the own breaker is tripped tocorrect such a situation. If the situationpersists the surrounding breakers should betripped to clear the unsymmetrical loadsituation.
The Polediscordance protection functionCCRPLD operates based on information fromauxiliary contacts of the circuit breaker forthe three phases with additional criteria fromunsymmetrical phase currents when required.
Directional over/underpowerprotection GOPPDOP/GUPPDUP
The directional over-/under-power protectionGOPPDOP/GUPPDUP can be used wherevera high/low active, reactive or apparent powerprotection or alarming is required. Thefunctions can alternatively be used to checkthe direction of active or reactive power flowin the power system. There are a number ofapplications where such functionality isneeded. Some of them are:
• detection of reversed active power flow• detection of high reactive power flow
Each function has two steps with definitetime delay. Reset times for both steps can beset as well.
Broken conductor check BRCPTOC
The main purpose of the function Brokenconductor check (BRCPTOC) is the detectionof broken conductors on protected powerlines and cables (series faults). Detection canbe used to give alarm only or trip the linebreaker.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 15
Capacitor bank protection(CBPGAPC)
Shunt Capacitor Banks (SCB) are used in apower system to provide reactive powercompensation and power factor correction.They are as well used as integral parts ofStatic Var Compensators (SVC) or HarmonicFilters installations. Capacitor bank protection(CBPGAPC) function is specially designed toprovide protection and supervision featuresfor SCBs.
5. Voltage protection
Two step undervoltage protectionUV2PTUV
Undervoltages can occur in the power systemduring faults or abnormal conditions. Twostep undervoltage protection (UV2PTUV)function can be used to open circuit breakersto prepare for system restoration at poweroutages or as long-time delayed back-up toprimary protection.
UV2PTUV has two voltage steps, each withinverse or definite time delay.
Two step overvoltage protectionOV2PTOV
Overvoltages may occur in the power systemduring abnormal conditions such as suddenpower loss, tap changer regulating failures,open line ends on long lines etc.
Two step overvoltage protection (OV2PTOV)function can be used to detect open lineends, normally then combined with adirectional reactive over-power function tosupervise the system voltage. When triggered,the function will cause an alarm, switch inreactors, or switch out capacitor banks.
OV2PTOV has two voltage steps, each ofthem with inverse or definite time delayed.
OV2PTOV has an extremely high reset ratioto allow settings close to system servicevoltage.
Two step residual overvoltageprotection ROV2PTOV
Residual voltages may occur in the powersystem during earth faults.
Two step residual overvoltage protectionROV2PTOV function calculates the residualvoltage from the three-phase voltage inputtransformers or measures it from a singlevoltage input transformer fed from an opendelta or neutral point voltage transformer.
ROV2PTOV has two voltage steps, each withinverse or definite time delay.
Reset delay ensures operation for intermittentearth faults.
Voltage differential protectionVDCPTOV
A voltage differential monitoring function isavailable. It compares the voltages from twothree phase sets of voltage transformers andhas one sensitive alarm step and one tripstep.Alternatively, it can be used as voltagedifferential protection (VDCPTOV) for shuntcapacitor banks.
Loss of voltage check LOVPTUV
Loss of voltage check (LOVPTUV) is suitablefor use in networks with an automatic systemrestoration function. LOVPTUV issues a three-pole trip command to the circuit breaker, ifall three phase voltages fall below the setvalue for a time longer than the set time andthe circuit breaker remains closed.
6. Frequency protection
Underfrequency protection SAPTUF
Underfrequency occurs as a result of lack ofgeneration in the network.
Underfrequency protection SAPTUF is usedfor load shedding systems, remedial actionschemes, gas turbine startup and so on.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
16 ABB
SAPTUF is provided with an undervoltageblocking.
The operation is based on positive sequencevoltage measurement and requires two phase-phase or three phase-neutral voltages to beconnected. For information about how toconnect analog inputs, refer to Applicationmanual/IED application/Analog inputs/Setting guidelines
Overfrequency protection SAPTOF
Overfrequency protection function SAPTOF isapplicable in all situations, where reliabledetection of high fundamental power systemfrequency is needed.
Overfrequency occurs at sudden load dropsor shunt faults in the power network. Closeto the generating plant, generator governorproblems can also cause over frequency.
SAPTOF is used mainly for generationshedding and remedial action schemes. It isalso used as a frequency stage initiating loadrestoring.
SAPTOF is provided with an undervoltageblocking.
The operation is based on positive sequencevoltage measurement and requires two phase-phase or three phase-neutral voltages to beconnected. For information about how toconnect analog inputs, refer to Applicationmanual/IED application/Analog inputs/Setting guidelines
Rate-of-change frequencyprotection SAPFRC
Rate-of-change frequency protection function(SAPFRC) gives an early indication of a maindisturbance in the system. SAPFRC can beused for generation shedding, load sheddingand remedial action schemes. SAPFRC candiscriminate between positive or negativechange of frequency.
SAPFRC is provided with an undervoltageblocking. The operation is based on positivesequence voltage measurement and requirestwo phase-phase or three phase-neutralvoltages to be connected. For information
about how to connect analog inputs, refer toApplication manual/IED application/Analog inputs/Setting guidelines.
7. Multipurposeprotection
General current and voltageprotection CVGAPC
The General current and voltage protection(CVGAPC) can be utilized as a negativesequence current protection detectingunsymmetrical conditions such as open phaseor unsymmetrical faults.
CVGAPC can also be used to improve phaseselection for high resistive earth faults,outside the distance protection reach, for thetransmission line. Three functions are used,which measures the neutral current and eachof the three phase voltages. This will give anindependence from load currents and thisphase selection will be used in conjunctionwith the detection of the earth fault from thedirectional earth fault protection function.
8. Secondary systemsupervision
Current circuit supervisionCCSRDIF
Open or short circuited current transformercores can cause unwanted operation of manyprotection functions such as differential,earth-fault current and negative-sequencecurrent functions.
It must be remembered that a blocking ofprotection functions at an occurrence of openCT circuit will mean that the situation willremain and extremely high voltages willstress the secondary circuit.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 17
Current circuit supervision (CCSRDIF)compares the residual current from a threephase set of current transformer cores withthe neutral point current on a separate inputtaken from another set of cores on thecurrent transformer.
A detection of a difference indicates a fault inthe circuit and is used as alarm or to blockprotection functions expected to giveunwanted tripping.
Fuse failure supervision SDDRFUF
The aim of the fuse failure supervisionfunction (SDDRFUF) is to block voltagemeasuring functions at failures in thesecondary circuits between the voltagetransformer and the IED in order to avoidunwanted operations that otherwise mightoccur.
The fuse failure supervision function basicallyhas three different algorithms, negativesequence and zero sequence basedalgorithms and an additional delta voltageand delta current algorithm.
The negative sequence detection algorithm isrecommended for IEDs used in isolated orhigh-impedance earthed networks. It is basedon the negative-sequence measuringquantities, a high value of voltage 3U2
without the presence of the negative-sequence current 3I2.
The zero sequence detection algorithm isrecommended for IEDs used in directly orlow impedance earthed networks. It is basedon the zero sequence measuring quantities, ahigh value of voltage 3U0 without the
presence of the residual current 3I0.
For better adaptation to system requirements,an operation mode setting has beenintroduced which makes it possible to selectthe operating conditions for negativesequence and zero sequence based function.The selection of different operation modesmakes it possible to choose differentinteraction possibilities between the negativesequence and zero sequence based algorithm.
A criterion based on delta current and deltavoltage measurements can be added to thefuse failure supervision function in order todetect a three phase fuse failure, which inpractice is more associated with voltagetransformer switching during stationoperations.
9. Control
Synchrocheck, energizing check,and synchronizing SESRSYN
The Synchronizing function allows closing ofasynchronous networks at the correctmoment including the breaker closing time,which improves the network stability.
Synchrocheck, energizing check, andsynchronizing (SESRSYN) function checksthat the voltages on both sides of the circuitbreaker are in synchronism, or with at leastone side dead to ensure that closing can bedone safely.
SESRSYN function includes a built-in voltageselection scheme for double bus and 1½breaker or ring busbar arrangements.
Manual closing as well as automatic reclosingcan be checked by the function and can havedifferent settings.
For systems which are running asynchronousa synchronizing function is provided. Themain purpose of the synchronizing functionis to provide controlled closing of circuitbreakers when two asynchronous systems aregoing to be connected. It is used for slipfrequencies that are larger than those forsynchrocheck and lower than a set maximumlevel for the synchronizing function.
Autorecloser SMBRREC
The autorecloser (SMBRREC) functionprovides high-speed and/or delayed auto-reclosing for single or multi-breakerapplications.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
18 ABB
Up to five reclosing attempts can be includedby parameter setting. The first attempt can besingle-, two and/or three phase for singlephase or multi-phase faults respectively.
Multiple autoreclosing functions are providedfor multi-breaker arrangements. A prioritycircuit allows one circuit breaker to close firstand the second will only close if the faultproved to be transient.
Each autoreclosing function can beconfigured to co-operate with a synchrocheckfunction.
Apparatus control APC
The apparatus control functions are used forcontrol and supervision of circuit breakers,disconnectors and earthing switches within abay. Permission to operate is given afterevaluation of conditions from other functionssuch as interlocking, synchrocheck, operatorplace selection and external or internalblockings.
Apparatus control features:
• Select-Execute principle to give highreliability
• Selection function to prevent simultaneousoperation
• Selection and supervision of operator place• Command supervision• Block/deblock of operation• Block/deblock of updating of position
indications• Substitution of position indications• Overriding of interlocking functions• Overriding of synchrocheck• Operation counter• Suppression of Mid position
Two types of command models can be used:
• Direct with normal security• SBO (Select-Before-Operate) with enhanced
security
In normal security, the command isprocessed and the resulting position is notsupervised. However with enhanced security,the command is processed and the resultingposition is supervised.
Normal security means that only thecommand is evaluated and the resultingposition is not supervised. Enhanced securitymeans that the command is evaluated with anadditional supervision of the status value ofthe control object. The command securitywith enhanced security is always terminatedby a CommandTermination service primitive.
Control operation can be performed from thelocal HMI under authority control if so defined.
Interlocking
The interlocking function blocks thepossibility to operate primary switchingdevices, for instance when a disconnector isunder load, in order to prevent materialdamage and/or accidental human injury.
Each apparatus control function hasinterlocking modules included for differentswitchyard arrangements, where eachfunction handles interlocking of one bay. Theinterlocking function is distributed to eachIED and is not dependent on any centralfunction. For the station-wide interlocking,the IEDs communicate via the system-wideinterbay bus (IEC 61850-8-1) or by using hardwired binary inputs/outputs. The interlockingconditions depend on the circuitconfiguration and apparatus position status atany given time.
For easy and safe implementation of theinterlocking function, the IED is deliveredwith standardized and tested softwareinterlocking modules containing logic for theinterlocking conditions. The interlockingconditions can be altered, to meet thecustomer’s specific requirements, by addingconfigurable logic by means of the graphicalconfiguration tool.
Voltage control TR1ATCC,TR8ATCC, TCMYLTC and TCLYLTC
The voltage control functions, Automaticvoltage control for tap changer, single controlTR1ATCC, Automatic voltage control for tapchanger , parallel control TR8ATCC and Tapchanger control and supervision, 6 binaryinputs TCMYLTC as well as Tap changer
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 19
control and supervision, 32 binary inputsTCLYLTC are used for control of powertransformers with a motor driven load tapchanger. The functions provide automaticregulation of the voltage on the secondaryside of transformers or alternatively on a loadpoint further out in the network.
Control of a single transformer, as well ascontrol of up to eight transformers in parallelis possible. For parallel control of powertransformers, three alternative methods areavailable, the master-follower method, thecirculating current method and the reversereactance method. The two former methodsrequire exchange of information between theparallel transformers and this is provided forwithin IEC61850-8-1.
Voltage control includes many extra featuressuch as possibility of to avoid simultaneoustapping of parallel transformers, hot stand byregulation of a transformer in a group whichregulates it to a correct tap position eventhough the LV CB is open, compensation fora possible capacitor bank on the LV side bayof a transformer, extensive tap changermonitoring including contact wear andhunting detection, monitoring of the powerflow in the transformer so that for example,the voltage control can be blocked if thepower reverses etc.
Logic rotating switch for functionselection and LHMI presentationSLGGIO
The logic rotating switch for functionselection and LHMI presentation function(SLGGIO) (or the selector switch functionblock) is used to get a selector switchfunctionality similar to the one provided by ahardware selector switch. Hardware selectorswitches are used extensively by utilities, inorder to have different functions operating onpre-set values. Hardware switches arehowever sources for maintenance issues,lower system reliability and an extendedpurchase portfolio. The logic selectorswitches eliminate all these problems.
Selector mini switch VSGGIO
The Selector mini switch VSGGIO functionblock is a multipurpose function used for avariety of applications, as a general purposeswitch.
VSGGIO can be controlled from the menu orfrom a symbol on the single line diagram(SLD) on the local HMI.
Single point generic control 8signals SPC8GGIO
The Single point generic control 8 signals(SPC8GGIO) function block is a collection of8 single point commands, designed to bringin commands from REMOTE (SCADA) tothose parts of the logic configuration that donot need extensive command receivingfunctionality (for example, SCSWI). In thisway, simple commands can be sent directlyto the IED outputs, without confirmation.Confirmation (status) of the result of thecommands is supposed to be achieved byother means, such as binary inputs andSPGGIO function blocks. The commands canbe pulsed or steady.
Single command, 16 signals
The IEDs can receive commands either froma substation automation system or from thelocal HMI. The command function block hasoutputs that can be used, for example, tocontrol high voltage apparatuses or for otheruser defined functionality.
10. Schemecommunication
Scheme communication logic fordistance or overcurrent protectionZCPSCH
To achieve instantaneous fault clearance forall line faults, a scheme communication logicis provided. All types of communicationschemes for example, permissive
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
20 ABB
underreaching, permissive overreaching,blocking, unblocking, intertrip are available.
The built-in communication module (LDCM)can be used for scheme communicationsignaling when included.
Current reversal and weak-endinfeed logic for distance protectionZCRWPSCH
The current reversal function is used toprevent unwanted operations due to currentreversal when using permissive overreachprotection schemes in application withparallel lines when the overreach from thetwo ends overlap on the parallel line.
The weak-end infeed logic is used in caseswhere the apparent power behind theprotection can be too low to activate thedistance protection function. When activated,received carrier signal together with localunder voltage criteria and no reverse zoneoperation gives an instantaneous trip. Thereceived signal is also echoed back toaccelerate the sending end.
Three phase or phase segregated schemelogic is available.
Local acceleration logic ZCLCPLAL
To achieve fast clearing of faults on thewhole line, when no communication channelis available, local acceleration logic(ZCLCPLAL) can be used. This logic enablesfast fault clearing during certain conditions,but naturally, it can not fully replace acommunication channel.
The logic can be controlled either by theautorecloser (zone extension) or by the loss-of-load current (loss-of-load acceleration).
Scheme communication logic forresidual overcurrent protectionECPSCH
To achieve fast fault clearance of earth faultson the part of the line not covered by theinstantaneous step of the residual overcurrentprotection, the directional residualovercurrent protection can be supported witha logic that uses communication channels.
In the directional scheme, information of thefault current direction must be transmitted tothe other line end. With directionalcomparison, a short operate time of theprotection including a channel transmissiontime, can be achieved. This short operatetime enables rapid autoreclosing functionafter the fault clearance.
The communication logic module fordirectional residual current protectionenables blocking as well as permissive under/overreaching schemes. The logic can also besupported by additional logic for weak-endinfeed and current reversal, included inCurrent reversal and weak-end infeed logicfor residual overcurrent protection(ECRWPSCH) function.
Current reversal and weak-endinfeed logic for residualovercurrent protection ECRWPSCH
The Current reversal and weak-end infeedlogic for residual overcurrent protectionECRWPSCH is a supplement to Schemecommunication logic for residual overcurrentprotection ECPSCH.
To achieve fast fault clearing for all earthfaults on the line, the directional earth-faultprotection function can be supported withlogic that uses communication channels.
The 670 series IEDs have for this reasonavailable additions to scheme communicationlogic.
If parallel lines are connected to commonbusbars at both terminals, overreachingpermissive communication schemes can tripunselectively due to fault current reversal.This unwanted tripping affects the healthyline when a fault is cleared on the other line.This lack of security can result in a total lossof interconnection between the two buses. Toavoid this type of disturbance, a fault currentreversal logic (transient blocking logic) canbe used.
Permissive communication schemes forresidual overcurrent protection can basicallyoperate only when the protection in the
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 21
remote IED can detect the fault. Thedetection requires a sufficient minimumresidual fault current, out from this IED. Thefault current can be too low due to anopened breaker or high-positive and/or zero-sequence source impedance behind this IED.To overcome these conditions, weak-endinfeed (WEI) echo logic is used.
11. Logic
Tripping logic SMPPTRC
A function block for protection tripping isprovided for each circuit breaker involved inthe tripping of the fault. It provides pulseprolongation to ensure a trip pulse ofsufficient length, as well as all functionalitynecessary for correct co-operation withautoreclosing functions.
The trip function block includes functionalityfor evolving faults and breaker lock-out.
Trip matrix logic TMAGGIO
Trip matrix logic TMAGGIO function is usedto route trip signals and other logical outputsignals to different output contacts on the IED.
TMAGGIO output signals and the physicaloutputs allows the user to adapt the signalsto the physical tripping outputs according tothe specific application needs.
Configurable logic blocks
A number of logic blocks and timers areavailable for the user to adapt theconfiguration to the specific application needs.
• OR function block.
• INVERTER function blocks that inverts theinput signal.
• PULSETIMER function block can be used,for example, for pulse extensions orlimiting of operation of outputs.
• GATE function block is used for whetheror not a signal should be able to pass fromthe input to the output.
• XOR function block.
• LOOPDELAY function block used to delaythe output signal one execution cycle.
• TIMERSET function has pick-up and drop-out delayed outputs related to the inputsignal. The timer has a settable time delay.
• AND function block.
• SRMEMORY function block is a flip-flopthat can set or reset an output from twoinputs respectively. Each block has twooutputs where one is inverted. The memorysetting controls if the block's output shouldreset or return to the state it was, after apower interruption. Set input has priority.
• RSMEMORY function block is a flip-flopthat can reset or set an output from twoinputs respectively. Each block has twooutputs where one is inverted. The memorysetting controls if the block's output shouldreset or return to the state it was, after apower interruption. Reset input has priority.
Configurable logic Q/TA number of logic blocks and timers with thecapability to propagate timestamp and qualityof the input signals are available. Thefunction blocks assist the user to adapt theIEDs configuration to the specific applicationneeds.
• ORQT function block that also propagatestimestamp and quality of input signals.
• INVERTERQT function block that invertsthe input signal and propagates timestampand quality of input signal.
• PULSETIMERQT function block can beused, for example, for pulse extensions orlimiting of operation of outputs. The
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
22 ABB
function also propagates timestamp andquality of input signal.
• XORQT function block. The function alsopropagates timestamp and quality of inputsignals.
• TIMERSETQT function has pick-up anddrop-out delayed outputs related to theinput signal. The timer has a settable timedelay. The function also propagatestimestamp and quality of input signal.
• ANDQT function block. The function alsopropagates timestamp and quality of inputsignals.
• SRMEMORYQT function block is a flip-flop that can set or reset an output fromtwo inputs respectively. Each block has twooutputs where one is inverted. The memorysetting controls if the block after a powerinterruption should return to the statebefore the interruption, or be reset. Thefunction also propagates timestamp andquality of input signal.
• RSMEMORYQT function block is a flip-flop that can reset or set an output fromtwo inputs respectively. Each block has twooutputs where one is inverted. The memorysetting controls if the block after a powerinterruption should return to the statebefore the interruption, or be reset. Thefunction also propagates timestamp andquality of input signal.
• INVALIDQT function which sets qualityinvalid of outputs according to a "valid"input. Inputs are copied to outputs. If inputVALID is 0, or if its quality invalid bit is set,all outputs invalid quality bit will be set toinvalid. The timestamp of an output will beset to the latest timestamp of INPUT andVALID inputs.
• INDCOMBSPQT combines single inputsignals to group signal. Single positioninput is copied to value part of SP_OUToutput. TIME input is copied to time part ofSP_OUT output. State input bits are copied
to the corresponding state part of SP_OUToutput. If the state or value on the SP_OUToutput changes, the Event bit in the statepart is toggled. The function alsopropagates timestamp and quality of inputsignals.
• INDEXTSPQT extracts individual signalsfrom a group signal input. Value part ofsingle position input is copied to SI_OUToutput. Time part of single position input iscopied to TIME output. State bits incommon part and indication part of inputssignal is copied to the corresponding stateoutput. The function also propagatestimestamp and quality of input signal.
Extension logic package
The logic extension block package includesadditional trip matrix logic and configurablelogic blocks.
Fixed signal function block
The Fixed signals function (FXDSIGN)generates a number of pre-set (fixed) signalsthat can be used in the configuration of anIED, either for forcing the unused inputs inother function blocks to a certain level/value,or for creating certain logic.
12. Monitoring
Measurements CVMMXN, CMMXU,VNMMXU, VMMXU, CMSQI, VMSQI
The measurement functions are used to get on-line information from the IED. These servicevalues make it possible to display on-lineinformation on the local HMI and on theSubstation automation system about:
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 23
• measured voltages, currents, frequency,active, reactive and apparent power andpower factor
• primary and secondary phasors• positive, negative and zero sequence
currents and voltages• mA, input currents• pulse counters
Supervision of mA input signals
The main purpose of the function is tomeasure and process signals from differentmeasuring transducers. Many devices used inprocess control represent various parameterssuch as frequency, temperature and DCbattery voltage as low current values, usuallyin the range 4-20 mA or 0-20 mA.
Alarm limits can be set and used as triggers,e.g. to generate trip or alarm signals.
The function requires that the IED isequipped with the mA input module.
Event counter CNTGGIO
Event counter (CNTGGIO) has six counterswhich are used for storing the number oftimes each counter input has been activated.
Disturbance report DRPRDRE
Complete and reliable information aboutdisturbances in the primary and/or in thesecondary system together with continuousevent-logging is accomplished by thedisturbance report functionality.
Disturbance report DRPRDRE, alwaysincluded in the IED, acquires sampled data ofall selected analog input and binary signalsconnected to the function block with a,maximum of 40 analog and 96 binary signals.
The Disturbance report functionality is acommon name for several functions:
• Event list• Indications• Event recorder• Trip value recorder• Disturbance recorder• Fault locator
The Disturbance report function ischaracterized by great flexibility regardingconfiguration, starting conditions, recordingtimes, and large storage capacity.
A disturbance is defined as an activation ofan input to the AxRADR or BxRBDR functionblocks, which are set to trigger thedisturbance recorder. All signals from start ofpre-fault time to the end of post-fault timewill be included in the recording.
Every disturbance report recording is savedin the IED in the standard Comtrade format.The same applies to all events, which arecontinuously saved in a ring-buffer. The localHMI is used to get information about therecordings. The disturbance report files maybe uploaded to PCM600 for further analysisusing the disturbance handling tool.
Event list DRPRDRE
Continuous event-logging is useful formonitoring the system from an overviewperspective and is a complement to specificdisturbance recorder functions.
The event list logs all binary input signalsconnected to the Disturbance report function.The list may contain up to 1000 time-taggedevents stored in a ring-buffer.
Indications DRPRDRE
To get fast, condensed and reliableinformation about disturbances in theprimary and/or in the secondary system it isimportant to know, for example binarysignals that have changed status during adisturbance. This information is used in theshort perspective to get information via thelocal HMI in a straightforward way.
There are three LEDs on the local HMI(green, yellow and red), which will displaystatus information about the IED and theDisturbance report function (trigged).
The Indication list function shows all selectedbinary input signals connected to theDisturbance report function that havechanged status during a disturbance.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
24 ABB
Event recorder DRPRDRE
Quick, complete and reliable informationabout disturbances in the primary and/or inthe secondary system is vital, for example,time-tagged events logged duringdisturbances. This information is used fordifferent purposes in the short term (forexample corrective actions) and in the longterm (for example functional analysis).
The event recorder logs all selected binaryinput signals connected to the Disturbancereport function. Each recording can containup to 150 time-tagged events.
The event recorder information is availablefor the disturbances locally in the IED.
The event recording information is anintegrated part of the disturbance record(Comtrade file).
Trip value recorder DRPRDRE
Information about the pre-fault and faultvalues for currents and voltages are vital forthe disturbance evaluation.
The Trip value recorder calculates the valuesof all selected analog input signals connectedto the Disturbance report function. The resultis magnitude and phase angle before andduring the fault for each analog input signal.
The trip value recorder information isavailable for the disturbances locally in theIED.
The trip value recorder information is anintegrated part of the disturbance record(Comtrade file).
Disturbance recorder DRPRDRE
The Disturbance recorder function suppliesfast, complete and reliable information aboutdisturbances in the power system. Itfacilitates understanding system behavior andrelated primary and secondary equipmentduring and after a disturbance. Recordedinformation is used for different purposes inthe short perspective (for example correctiveactions) and long perspective (for examplefunctional analysis).
The Disturbance recorder acquires sampleddata from selected analog- and binary signalsconnected to the Disturbance report function(maximum 40 analog and 96 binary signals).The binary signals available are the same asfor the event recorder function.
The function is characterized by greatflexibility and is not dependent on theoperation of protection functions. It canrecord disturbances not detected byprotection functions. Up to ten seconds ofdata before the trigger instant can be saved inthe disturbance file.
The disturbance recorder information for upto 100 disturbances are saved in the IED andthe local HMI is used to view the list ofrecordings.
Event function
When using a Substation Automation systemwith LON or SPA communication, time-tagged events can be sent at change orcyclically from the IED to the station level.These events are created from any availablesignal in the IED that is connected to theEvent function (EVENT). The event functionblock is used for LON and SPAcommunication.
Analog and double indication values are alsotransferred through EVENT function.
IEC61850 generic communicationI/O function SPGGIO
IEC61850 generic communication I/Ofunctions (SPGGIO) is used to send onesingle logical signal to other systems orequipment in the substation.
IEC61850 generic communicationI/O functions MVGGIO
IEC61850 generic communication I/Ofunctions (MVGGIO) function is used to sendthe instantaneous value of an analog outputto other systems or equipment in thesubstation. It can also be used inside thesame IED, to attach a RANGE aspect to ananalog value and to permit measurementsupervision on that value.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 25
Measured value expander blockRANGE_XP
The current and voltage measurementsfunctions (CVMMXN, CMMXU, VMMXU andVNMMXU), current and voltage sequencemeasurement functions (CMSQI and VMSQI)and IEC 61850 generic communication I/Ofunctions (MVGGIO) are provided withmeasurement supervision functionality. Allmeasured values can be supervised with foursettable limits: low-low limit, low limit, highlimit and high-high limit. The measure valueexpander block (RANGE_XP) has beenintroduced to enable translating the integeroutput signal from the measuring functions to5 binary signals: below low-low limit, belowlow limit, normal, above high-high limit orabove high limit. The output signals can beused as conditions in the configurable logicor for alarming purpose.
Fault locator LMBRFLO
The accurate fault locator is an essentialcomponent to minimize the outages after apersistent fault and/or to pin-point a weakspot on the line.
The fault locator is an impedance measuringfunction giving the distance to the fault inpercent, km or miles. The main advantage isthe high accuracy achieved by compensatingfor load current and for the mutual zero-sequence effect on double circuit lines.
The compensation includes setting of theremote and local sources and calculation ofthe distribution of fault currents from eachside. This distribution of fault current,together with recorded load (pre-fault)currents, is used to exactly calculate the faultposition. The fault can be recalculated withnew source data at the actual fault to furtherincrease the accuracy.
Especially on heavily loaded long lines(where the fault locator is most important)where the source voltage angles can be up to35-40 degrees apart the accuracy can be stillmaintained with the advanced compensationincluded in fault locator.
13. Metering
Pulse counter logic PCGGIO
Pulse counter (PCGGIO) function countsexternally generated binary pulses, forinstance pulses coming from an externalenergy meter, for calculation of energyconsumption values. The pulses are capturedby the binary input module and then read bythe function. A scaled service value isavailable over the station bus. The specialBinary input module with enhanced pulsecounting capabilities must be ordered toachieve this functionality.
Function for energy calculation anddemand handling ETPMMTR
Outputs from the Measurements (CVMMXN)function can be used to calculate energyconsumption. Active as well as reactivevalues are calculated in import and exportdirection. Values can be read or generated aspulses. Maximum demand power values arealso calculated by the function.
14. Basic IED functions
Time synchronization
The time synchronization source selector isused to select a common source of absolutetime for the IED when it is a part of a controland a protection system. This makes itpossible to compare event- and disturbancedata between all IEDs in a station automationsystem possible.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
26 ABB
15. Human machineinterface
Human machine interface
The local human machine interface isavailable in a small and a medium sizedmodel. The difference between the twomodels is the size of the LCD. The small sizeLCD can display seven lines of text and themedium size LCD can display the single linediagram with up to 15 objects on each page.Up to 12 single line diagram pages can bedefined, depending on the product capability.
The local HMI is divided into zones withdifferent functionality.
• Status indication LEDs.• Alarm indication LEDs, which consist of
15 LEDs (6 red and 9 yellow) with userprintable label. All LEDs are configurablefrom PCM600.
• Liquid crystal display (LCD).• Keypad with push buttons for control
and navigation purposes, switch forselection between local and remotecontrol and reset.
• Isolated RJ45 communication port.
IEC05000055-LITEN V1 EN
Figure 1. Small, alpha numeric HMI
IEC05000056-LITEN V1 EN
Figure 2. Medium graphic HMI, 15controllable objects
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 27
16. Stationcommunication
Overview
Each IED is provided with a communicationinterface, enabling it to connect to one ormany substation level systems or equipment,either on the Substation Automation (SA) busor Substation Monitoring (SM) bus.
Following communication protocols areavailable:
• IEC 61850-8-1 communication protocol• LON communication protocol• SPA or IEC 60870-5-103 communication
protocol• DNP3.0 communication protocol
Theoretically, several protocols can becombined in the same IED.
IEC 61850-8-1 communicationprotocol
The IED is equipped with single or doubleoptical Ethernet rear ports (order dependent)for IEC 61850-8-1 station bus communication.The IEC 61850-8-1 communication is alsopossible from the optical Ethernet front port.IEC 61850-8-1 protocol allows intelligentelectrical devices (IEDs) from differentvendors to exchange information andsimplifies system engineering. Peer-to-peercommunication according to GOOSE is partof the standard. Disturbance files uploadingis provided.
Serial communication, LON
Existing stations with ABB station bus LONcan be extended with use of the optical LONinterface. This allows full SA functionalityincluding peer-to-peer messaging andcooperation between existing ABB IED's andthe new IED 670.
SPA communication protocol
A single glass or plastic port is provided forthe ABB SPA protocol. This allows extensions
of simple substation automation systems butthe main use is for Substation MonitoringSystems SMS.
IEC 60870-5-103 communicationprotocol
A single glass or plastic port is provided forthe IEC60870-5-103 standard. This allowsdesign of simple substation automationsystems including equipment from differentvendors. Disturbance files uploading isprovided.
DNP3.0 communication protocol
An electrical RS485 and an optical Ethernetport is available for the DNP3.0communication. DNP3.0 Level 2communication with unsolicited events, timesynchronizing and disturbance reporting isprovided for communication to RTUs,Gateways or HMI systems.
Multiple command and transmit
When 670 IED's are used in SubstationAutomation systems with LON, SPA orIEC60870-5-103 communication protocols theEvent and Multiple Command function blocksare used as the communication interface forvertical communication to station HMI andgateway and as interface for horizontal peer-to-peer communication (over LON only).
Duo driver configuration DUODRV
Redundant station bus communication isused to assure communication, even thoughone communication channels might not beavailable for some reason. Redundantcommunication over station bus running IEC61850-8-1 use both port AB and CD on OEMmodule and IEC 62439-PRP protocol.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
28 ABB
17. Remotecommunication
Analog and binary signal transferto remote end
Three analog and eight binary signals can beexchanged between two IEDs. Thisfunctionality is mainly used for the linedifferential protection. However it can beused in other products as well. An IED cancommunicate with up to 4 remote IEDs.
Binary signal transfer to remoteend, 192 signals
If the communication channel is used fortransfer of binary signals only, up to 192binary signals can be exchanged betweentwo IEDs. For example, this functionality canbe used to send information such as status ofprimary switchgear apparatus or intertrippingsignals to the remote IED. An IED cancommunicate with up to 4 remote IEDs.
Line data communication module,short and medium range LDCM
The line data communication module (LDCM)is used for communication between the IEDssituated at distances <110 km or from theIED to optical to electrical converter with G.703 or G.703E1 interface located on adistances <3 km away. The LDCM modulesends and receives data, to and from anotherLDCM module. The IEEE/ANSI C37.94standard format is used.
Galvanic interface G.703 resp G.703E1
The external galvanic data communicationconverter G.703/G.703E1 makes an optical-to-galvanic conversion for connection to amultiplexer. These units are designed for 64kbit/s resp 2Mbit/s operation. The converteris delivered with 19” rack mountingaccessories.
18. Hardware description
Hardware modules
Power supply module PSM
The power supply module is used to providethe correct internal voltages and full isolationbetween the terminal and the battery system.An internal fail alarm output is available.
Binary input module BIM
The binary input module has 16 opticallyisolated inputs and is available in twoversions, one standard and one withenhanced pulse counting capabilities on theinputs to be used with the pulse counterfunction. The binary inputs are freelyprogrammable and can be used for the inputof logical signals to any of the functions.They can also be included in the disturbancerecording and event-recording functions. Thisenables extensive monitoring and evaluationof operation of the IED and for all associatedelectrical circuits.
Binary output module BOM
The binary output module has 24independent output relays and is used fortrip output or any signaling purpose.
Static binary output module SOM
The static binary output module has six faststatic outputs and six change over outputrelays for use in applications with high speedrequirements.
Binary input/output module IOM
The binary input/output module is usedwhen only a few input and output channelsare needed. The ten standard output channelsare used for trip output or any signalingpurpose. The two high speed signal outputchannels are used for applications whereshort operating time is essential. Eightoptically isolated binary inputs cater forrequired binary input information.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 29
mA input module MIM
The milli-ampere input module is used tointerface transducer signals in the –20 to +20mA range from for example OLTC position,temperature or pressure transducers. Themodule has six independent, galvanicallyseparated channels.
Optical ethernet module OEM
The optical fast-ethernet module is used toconnect an IED to the communication buses(like the station bus) that use the IEC61850-8-1 protocol (port A, B). The modulehas one or two optical ports with STconnectors.
Serial and LON communication moduleSLM, supports SPA/IEC 60870-5-103, LONand DNP 3.0
The serial and LON communication module(SLM) is used for SPA, IEC 60870-5-103,DNP3 and LON communication. The modulehas two optical communication ports forplastic/plastic, plastic/glass or glass/glass.One port is used for serial communication(SPA, IEC 60870-5-103 and DNP3 port ordedicated IEC 60870-5-103 port depending onordered SLM module) and one port isdedicated for LON communication.
Line data communication module LDCM
Each module has one optical port, one foreach remote end to which the IEDcommunicates.
Alternative cards for Medium range (1310 nmsingle mode) and Short range (850 nm multimode) are available.
Galvanic RS485 serial communicationmodule
The Galvanic RS485 communication module(RS485) is used for DNP3.0 communication.The module has one RS485 communicationport. The RS485 is a balanced serialcommunication that can be used either in 2-
wire or 4-wire connections. A 2-wireconnection uses the same signal for RX andTX and is a multidrop communication withno dedicated Master or slave. This variantrequires however a control of the output. The4-wire connection has separated signals forRX and TX multidrop communication with adedicated Master and the rest are slaves. Nospecial control signal is needed in this case.
GPS time synchronization module GTM
This module includes a GPS receiver used fortime synchronization. The GPS has one SMAcontact for connection to an antenna. It alsoincludes an optical PPS ST-connector output.
IRIG-B Time synchronizing module
The IRIG-B time synchronizing module isused for accurate time synchronizing of theIED from a station clock.
Electrical (BNC) and optical connection (ST)for 0XX and 12X IRIG-B support.
Transformer input module TRM
The transformer input module is used togalvanically separate and transform thesecondary currents and voltages generated bythe measuring transformers. The module hastwelve inputs in different combinations ofcurrents and voltage inputs.
Alternative connectors of Ring lug orCompression type can be ordered.
High impedance resistor unit
The high impedance resistor unit, withresistors for pick-up value setting and avoltage dependent resistor, is available in asingle phase unit and a three phase unit.Both are mounted on a 1/1 19 inch apparatusplate with compression type terminals.
Layout and dimensions
Dimensions
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
30 ABB
xx05000003.vsd
CB
E
F
A
D
IEC05000003 V1 EN
Figure 3. 1/2 x 19” case with rear cover
xx05000004.vsd
IEC05000004 V1 EN
Figure 4. Side-by-side mounting
Case size A B C D E F
6U, 1/2 x 19” 265.9 223.7 201.1 242.1 252.9 205.7
6U, 3/4 x 19” 265.9 336.0 201.1 242.1 252.9 318.0
6U, 1/1 x 19” 265.9 448.1 201.1 242.1 252.9 430.3
(mm)
Mounting alternatives
The following mounting alternatives areavailable (IP40 protection from the front):
• 19” rack mounting kit• Flush mounting kit with cut-out
dimensions:
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 31
1/2 case size (h) 254.3 mm (w) 210.1mm
3/4 case size (h) 254.3 mm (w) 322.4mm
1/1 case size (h) 254.3 mm (w) 434.7mm
• Wall mounting kit
See ordering for details about availablemounting alternatives.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
32 ABB
19. Connection diagrams
Table 1. Designations for 1/2 x 19” casing with 1 TRM slot
1MRK002801-AC 2 670 1.2 PG V1 EN
Module Rear Positions
PSM X11
BIM, BOM, SOM, IOM orMIM
X31 and X32 etc. to X51and X52
SLM X301:A, B, C, D
LDCM, IRIG-B or RS485 X302
LDCM or RS485 X303
OEM X311:A, B, C, D
LDCM, RS485 or GTM X312, 313
TRM X401
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 33
Table 2. Designations for 3/4 x 19” casing with 1 TRM slot
1MRK002801-AC 3 670 1.2 PG V1 EN
Module Rear Positions
PSM X11
BIM, BOM, SOM, IOM orMIM
X31 and X32 etc. toX101 and X102
SLM X301:A, B, C, D
LDCM, IRIG-B or RS485 X302
LDCM or RS485 X303
OEM X311:A, B, C, D
LDCM, RS485 or GTM X312, X313
TRM X401
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
34 ABB
Table 3. Designations for 3/4 x 19” casing with 2 TRM slot
1MRK002801-AC 4 670 1.2 PG V1 EN
Module Rear Positions
PSM X11
BIM, BOM, SOM, IOM orMIM
X31 and X32 etc. to X71 andX72
SLM X301:A, B, C, D
LDCM, IRIG-B or RS485 X302
LDCM or RS485 X303
OEM X311:A, B, C, D
LDCM, RS485 or GTM X312, X313, X322, X323
TRM 1 X401
TRM 2 X411
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 35
Table 4. Designations for 1/1 x 19” casing with 1 TRM slot
1MRK002801-AC 5 670 1.2 PG V1 EN
Module Rear Positions
PSM X11
BIM, BOM, SOM,IOM or MIM
X31 and X32 etc. to X161and X162
SLM X301:A, B, C, D
LDCM, IRIG-B orRS485
X302
LDCM or RS485 X303
OEM X311:A, B, C, D
LDCM,RS485 orGTM
X312, X313
TRM X401
Table 5. Designations for 1/1 x 19” casing with 2 TRM slots
1MRK002801-AC 6 670 1.2 PG V1 EN
Module Rear Positions
PSM X11
BIM, BOM, SOM,IOM or MIM
X31 and X32 etc. to X131and X132
SLM X301:A, B, C, D
LDCM, IRIG-B orRS485
X302
LDCM or RS485 X303
OEM X311:A, B, C, D
LDCM, RS485 orGTM
X312, X313, X322, X323
TRM 1 X401
TRM 2 X411
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
36 ABB
1MRK002801-AC 10 670 1.2 PG V1 EN
Figure 5. Transformer input module (TRM)
Indicates high polarity
CT/VT-input designation according to figure 5
Curr
ent/
volt
age
confi
gura
tion
(50/
60 H
z)
AI01 AI02 AI03 AI04 AI05 AI06 AI07 AI08 AI09 AI10 AI11 AI12
12I, 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A
12I, 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A
9I+3U,1A
1A 1A 1A 1A 1A 1A 1A 1A 1A 110-220V 110-220V 110-220V
9I+3U,5A
5A 5A 5A 5A 5A 5A 5A 5A 5A 110-220V 110-220V 110-220V
5I, 1A+4I, 5A+3U
1A 1A 1A 1A 1A 5A 5A 5A 5A 110-220V 110-220V 110-220V
7I+5U,1A
1A 1A 1A 1A 1A 1A 1A 110-220V 110-220V 110-220V 110-220V 110-220V
7I+5U,5A
5A 5A 5A 5A 5A 5A 5A 110-220V 110-220V 110-220V 110-220V 110-220V
6I, 5A+1I, 1A+5U
5A 5A 5A 5A 5A 5A 1A 110-220V 110-220V 110-220V 110-220V 110-220V
3I, 5A+4I, 1A+5U
5A 5A 5A 1A 1A 1A 1A 110-220V 110-220V 110-220V 110-220V 110-220V
3IM, 1A+4IP,1A+5U
1AM*)
1AM*)
1AM*)
1A 1A 1A 1A 110-220V 110-220V 110-220V 110-220V 110-220V
3IM, 5A+4IP,5A+5U
5AM*)
5AM*)
5AM*)
5A 5A 5A 5A 110-220V 110-220V 110-220V 110-220V 110-220V
6I+6U,1A
1A 1A 1A 1A 1A 1A 110-220V 110-220V 110-220V 110-220V 110-220V 110-220V
6I+6U,5A
5A 5A 5A 5A 5A 5A 110-220V 110-220V 110-220V 110-220V 110-220V 110-220V
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 37
3I, 5A+3I, 1A+6U
5 A 5 A 5 A 1A 1A 1A 110-220V 110-220V 110-220V 110-220V 110-220V 110-220V
6I, 1A 1A 1A 1A 1A 1A 1A - - - - - -
6I, 5A 5A 5A 5A 5A 5A 5A - - - - - -
*) Metering
Note that internal polarity can be adjusted by setting of analog input CT neutral direction and/or on SMAI pre-processing function blocks.
1MRK002801-AC 11 670 1.2 PG V1 EN
Figure 6. Binary input module (BIM). Inputcontacts named XA corresponds torear position X31, X41, and so on,and input contacts named XB torear position X32, X42, and so on.
1MRK002801-AC 15 670 1.2 PG V1 EN
Figure 7. mA input module (MIM)
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
38 ABB
1MRK002801-AC 8 670 1.2 PG V1 EN
Figure 8. IED with basic functionality and communication interfaces
1MRK002801-AC 7 670 1.2 PG V1 EN
Figure 9. Power supply module (PSM)
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 39
1MRK002801-AC 12 670 1.2 PG V1 EN
Figure 10. Binary output module (BOM). Output contacts named XA corresponds to rearposition X31, X41, and so on, and output contacts named XB to rear positionX32, X42, and so on.
1MRK002801-AC 13 670 1.2 PG V1 EN
Figure 11. Static output module (SOM)
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
40 ABB
1MRK002801-AC 14 670 1.2 PG V1 EN
Figure 12. Binary in/out module (IOM). Input contacts named XA corresponds to rear positionX31, X41, and so on, and output contacts named XB to rear position X32, X42,and so on.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 41
20. Technical data
General
Definitions
Referencevalue
The specified value of an influencing factor to which are referred thecharacteristics of the equipment
Nominalrange
The range of values of an influencing quantity (factor) within which, underspecified conditions, the equipment meets the specified requirements
Operativerange
The range of values of a given energizing quantity for which the equipment,under specified conditions, is able to perform its intended functionsaccording to the specified requirements
Energizing quantities, rated valuesand limits
Analog inputs
Table 6. TRM - Energizing quantities, rated values and limits for protection transformermodules
Quantity Rated value Nominal range
Current Ir = 1 or 5 A (0.2-40) × Ir
Operative range (0-100) x Ir
Permissive overload 4 × Ir cont.
100 × Ir for 1 s *)
Burden < 150 mVA at Ir = 5 A
< 20 mVA at Ir = 1 A
Ac voltage Ur = 110 V 0.5–288 V
Operative range (0–340) V
Permissive overload 420 V cont.450 V 10 s
Burden < 20 mVA at 110 V
Frequency fr = 50/60 Hz ± 5%
*) max. 350 A for 1 s when COMBITEST test switch is included.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
42 ABB
Table 7. TRM - Energizing quantities, rated values and limits for measuring transformermodules
Quantity Rated value Nominal range
Current Ir = 1 or 5 A (0-1.8) × Irat Ir = 1 A
(0-1.6) × Irat Ir = 5 A
Permissive overload 1.1 × Ir cont.
1.8 × Ir for 30 min at Ir =
1 A1.6 × Ir for 30 min at Ir =
5 A
Burden < 350 mVA at Ir = 5 A
< 200 mVA at Ir = 1 A
Ac voltage Ur = 110 V 0.5–288 V
Operative range (0–340) V
Permissive overload 420 V cont.450 V 10 s
Burden < 20 mVA at 110 V
Frequency fr = 50/60 Hz ± 5%
Table 8. MIM - mA input module
Quantity: Rated value: Nominal range:
Input resistance Rin = 194 Ohm -
Input range ± 5, ± 10, ± 20mA0-5, 0-10, 0-20, 4-20mA
-
Power consumptioneach mA-boardeach mA input
£ 2 W£ 0.1 W
-
Table 9. OEM - Optical ethernet module
Quantity Rated value
Number of channels 1 or 2
Standard IEEE 802.3u 100BASE-FX
Type of fiber 62.5/125 mm multimode fibre
Wave length 1300 nm
Optical connector Type ST
Communication speed Fast Ethernet 100 MB
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 43
Auxiliary DC voltage
Table 10. PSM - Power supply module
Quantity Rated value Nominal range
Auxiliary dc voltage, EL (input) EL = (24 - 60) VEL = (90 - 250) V
EL ± 20%EL ± 20%
Power consumption 50 W typically -
Auxiliary DC power in-rush < 5 A during 0.1 s -
Binary inputs and outputs
Table 11. BIM - Binary input module
Quantity Rated value Nominal range
Binary inputs 16 -
DC voltage, RL 24/30 V48/60 V110/125 V220/250 V
RL ± 20%RL ± 20%RL ± 20%RL ± 20%
Power consumption24/30 V48/60 V110/125 V220/250 V
max. 0.05 W/inputmax. 0.1 W/inputmax. 0.2 W/inputmax. 0.4 W/input
-
Counter input frequency 10 pulses/s max -
Oscillating signal discriminator Blocking settable 1–40 HzRelease settable 1–30 Hz
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
44 ABB
Table 12. BIM - Binary input module with enhanced pulse counting capabilities
Quantity Rated value Nominal range
Binary inputs 16 -
DC voltage, RL 24/30 V48/60 V110/125 V220/250 V
RL ± 20%RL ± 20%RL ± 20%RL ± 20%
Power consumption24/30 V48/60 V110/125 V220/250 V
max. 0.05 W/inputmax. 0.1 W/inputmax. 0.2 W/inputmax. 0.4 W/input
-
Counter input frequency 10 pulses/s max -
Balanced counter input frequency 40 pulses/s max -
Oscillating signal discriminator Blocking settable 1–40 HzRelease settable 1–30 Hz
Table 13. IOM - Binary input/output module
Quantity Rated value Nominal range
Binary inputs 8 -
DC voltage, RL 24/30 V48/60 V110/125 V220/250 V
RL ± 20%RL ± 20%RL ± 20%RL ± 20%
Power consumption24/30 V48/60 V110/125 V220/250 V
max. 0.05 W/inputmax. 0.1 W/inputmax. 0.2 W/inputmax. 0.4 W/input
-
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 45
Table 14. IOM - Binary input/output module contact data (reference standard: IEC61810-2)
Function or quantity Trip and signal relays Fast signal relays(parallel reed relay)
Binary outputs 10 2
Max system voltage 250 V AC, DC 250 V AC, DC
Test voltage across open contact, 1 min 1000 V rms 800 V DC
Current carrying capacityContinuous1 s
8 A10 A
8 A10 A
Making capacity at inductive load withL/R>10 ms0.2 s1.0 s
30 A10 A
0.4 A0.4 A
Breaking capacity for AC, cos φ > 0.4 250 V/8.0 A 250 V/8.0 A
Breaking capacity for DC with L/R < 40ms
48 V/1 A110 V/0.4 A125 V/0.35 A220 V/0.2 A250 V/0.15 A
48 V/1 A110 V/0.4 A125 V/0.35 A220 V/0.2 A250 V/0.15 A
Maximum capacitive load - 10 nF
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
46 ABB
Table 15. SOM - Static Output Module (reference standard: IEC 61810-2): Static binaryoutputs
Function of quantity Static binary output trip
Rated voltage 48 - 60 VDC 110 - 250 VDC
Number of outputs 6 6
Impedance open state ~300 kΩ ~810 kΩ
Test voltage across opencontact, 1 min
No galvanic separation No galvanic separation
Current carrying capacity:
Continuous 5A 5A
1.0s 10A 10A
Making capacity at capacitiveload with the maximumcapacitance of 0.2 μF :
0.2s 30A 30A
1.0s 10A 10A
Breaking capacity for DC with L/R ≤ 40ms
48V / 1A 110V / 0.4A
60V / 0,75A 125V / 0.35A
220V / 0.2A
250V / 0.15A
Operating time <1ms <1ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 47
Table 16. SOM - Static Output module data (reference standard: IEC 61810-2):Electromechanical relay outputs
Function of quantity Trip and signal relays
Max system voltage 250V AC/DC
Number of outputs 6
Test voltage across open contact, 1 min 1000V rms
Current carrying capacity:
Continuous 8A
1.0s 10A
Making capacity at capacitive load with themaximum capacitance of 0.2 μF:
0.2s 30A
1.0s 10A
Breaking capacity for DC with L/R ≤ 40ms 48V / 1A
110V / 0.4A
125V / 0,35A
220V / 0,2A
250V / 0.15A
Table 17. BOM - Binary output module contact data (reference standard: IEC 61810-2)
Function or quantity Trip and Signal relays
Binary outputs 24
Max system voltage 250 V AC, DC
Test voltage across open contact, 1 min 1000 V rms
Current carrying capacityContinuous1 s
8 A10 A
Making capacity at inductive load with L/R>10 ms0.2 s1.0 s
30 A10 A
Breaking capacity for AC, cos j>0.4 250 V/8.0 A
Breaking capacity for DC with L/R < 40 ms 48 V/1 A110 V/0.4 A125 V/0.35 A220 V/0.2 A250 V/0.15 A
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
48 ABB
Influencing factors
Table 18. Temperature and humidity influence
Parameter Reference value Nominal range Influence
Ambienttemperature, operatevalue
+20 °C -10 °C to +55 °C 0.02% /°C
Relative humidityOperative range
10%-90%0%-95%
10%-90% -
Storage temperature -40 °C to +70 °C - -
Table 19. Auxiliary DC supply voltage influence on functionality during operation
Dependence on Referencevalue
Withinnominal range
Influence
Ripple, in DC auxiliary voltageOperative range
max. 2%Full waverectified
15% of EL 0.01% /%
Auxiliary voltage dependence,operate value
± 20% of EL 0.01% /%
Interrupted auxiliary DC voltage
24-60 V DC ±20%90-250 V DC ±20%
Interruptioninterval0–50 ms
No restart
0–∞ s Correct behaviour atpower down
Restart time <180 s
Table 20. Frequency influence (reference standard: IEC 60255–1)
Dependence on Within nominal range Influence
Frequency dependence, operatevalue
fr ± 2.5 Hz for 50 Hz
fr ± 3.0 Hz for 60 Hz
± 1.0% / Hz
Harmonic frequencydependence (20% content)
2nd, 3rd and 5th harmonic of fr ± 1.0%
Harmonic frequencydependence for high impedancedifferential protection (10%content)
2nd, 3rd and 5th harmonic of fr ±5.0%
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 49
Type tests according to standards
Table 21. Electromagnetic compatibility
Test Type test values Reference standards
1 MHz burst disturbance 2.5 kV IEC 60255-22-1
100 kHz slow damped oscillatorywave immunity test
2.5 kV IEC 61000-4-18, Class III
Ring wave immunity test, 100 kHz 2-4 kV IEC 61000-4-12, Class IV
Surge withstand capability test 2.5 kV, oscillatory4.0 kV, fast transient
IEEE/ANSI C37.90.1
Electrostatic dischargeDirect applicationIndirect application
15 kV air discharge8 kV contact discharge8 kV contact discharge
IEC 60255-22-2, Class IV IEC 61000-4-2, Class IV
Electrostatic dischargeDirect applicationIndirect application
15 kV air discharge8 kV contact discharge8 kV contact discharge
IEEE/ANSI C37.90.1
Fast transient disturbance 4 kV IEC 60255-22-4, Class A
Surge immunity test 1-2 kV, 1.2/50 mshigh energy
IEC 60255-22-5
Power frequency immunity test 150-300 V, 50 Hz IEC 60255-22-7, Class A
Conducted common modeimmunity test
15 Hz-150 kHz IEC 61000-4-16, Class IV
Power frequency magnetic field test 1000 A/m, 3 s100 A/m, cont.
IEC 61000-4-8, Class V
Damped oscillatory magnetic fieldtest
100 A/m IEC 61000-4-10, Class V
Radiated electromagnetic fielddisturbance
20 V/m, 80-1000 MHz 1.4-2.7 GHz
IEC 60255-22-3
Radiated electromagnetic fielddisturbance
35 V/m26-1000 MHz
IEEE/ANSI C37.90.2
Conducted electromagnetic fielddisturbance
10 V, 0.15-80 MHz IEC 60255-22-6
Radiated emission 30-1000 MHz IEC 60255-25
Conducted emission 0.15-30 MHz IEC 60255-25
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
50 ABB
Table 22. Insulation
Test Type test values Reference standard
Dielectric test 2.0 kV AC, 1 min. IEC 60255-5
Impulse voltage test 5 kV, 1.2/50 ms, 0.5 J
Insulation resistance >100 MW at 500 VDC
Table 23. Environmental tests
Test Type test value Reference standard
Cold test Test Ad for 16 h at -25°C IEC 60068-2-1
Storage test Test Ad for 16 h at -40°C IEC 60068-2-1
Dry heat test Test Bd for 16 h at +70°C IEC 60068-2-2
Damp heat test, steady state Test Ca for 4 days at +40 °C andhumidity 93%
IEC 60068-2-78
Damp heat test, cyclic Test Db for 6 cycles at +25 to +55°C and humidity 93 to 95% (1 cycle= 24 hours)
IEC 60068-2-30
Table 24. CE compliance
Test According to
Immunity EN 50263
Emissivity EN 50263
Low voltage directive EN 50178
Table 25. Mechanical tests
Test Type test values Reference standards
Vibration response test Class II IEC 60255-21-1
Vibration endurance test Class I IEC 60255-21-1
Shock response test Class II IEC 60255-21-2
Shock withstand test Class I IEC 60255-21-2
Bump test Class I IEC 60255-21-2
Seismic test Class II IEC 60255-21-3
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 51
Differential protection
Table 26. 1Ph High impedance differential protection HZPDIF
Function Range or value Accuracy
Operate voltage (20-400) VI=U/R
± 1.0% of Ir
Reset ratio >95% -
Maximum continuous voltage U>Trip2/series resistor ≤200 W -
Operate time 10 ms typically at 0 to 10 x Ud -
Reset time 90 ms typically at 10 to 0 x Ud -
Critical impulse time 2 ms typically at 0 to 10 x Ud -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
52 ABB
Current protection
Table 27. Instantaneous phase overcurrent protection PHPIOC
Function Range or value Accuracy
Operate current (1-2500)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Operate time 25 ms typically at 0 to 2 x Iset -
Reset time 25 ms typically at 2 to 0 x Iset -
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Operate time 10 ms typically at 0 to 10 x Iset -
Reset time 35 ms typically at 10 to 0 x Iset -
Critical impulse time 2 ms typically at 0 to 10 x Iset -
Dynamic overreach < 5% at t = 100 ms -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 53
Table 28. Four step phase overcurrent protection OC4PTOC
Function Setting range Accuracy
Operate current (1-2500)% of lBase ± 1.0% of Ir at I ≤ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Min. operating current (1-100)% of lBase ± 1.0% of Ir at I ≤ Ir±1.0% of I at I > Ir
Relay characteristic angle(RCA)
(-70.0– -50.0) degrees ± 2.0 degrees
Maximum forward angle (40.0–70.0) degrees ± 2.0 degrees
Minimum forward angle (75.0–90.0) degrees ± 2.0 degrees
2nd harmonic blocking (5–100)% of fundamental ± 2.0% of Ir
Independent time delay (0.000-60.000) s ± 0.5% ±10 ms
Minimum operate time (0.000-60.000) s ± 0.5% ±10 ms
Inverse characteristics,see table 95, table 96 andtable 97
19 curve types See table 95, table 96 andtable 97
Operate time, startfunction
25 ms typically at 0 to 2 x Iset -
Reset time, start function 25 ms typically at 2 to 0 x Iset -
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Impulse margin time 15 ms typically -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
54 ABB
Table 29. Instantaneous residual overcurrent protection EFPIOC
Function Range or value Accuracy
Operate current (1-2500)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Operate time 25 ms typically at 0 to 2 x Iset -
Reset time 25 ms typically at 2 to 0 x Iset -
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Operate time 10 ms typically at 0 to 10 x Iset -
Reset time 35 ms typically at 10 to 0 x Iset -
Critical impulse time 2 ms typically at 0 to 10 x Iset -
Dynamic overreach < 5% at t = 100 ms -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 55
Table 30. Four step residual overcurrent protection EF4PTOC
Function Range or value Accuracy
Operate current (1-2500)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Operate current fordirectional comparison
(1–100)% of lBase ± 1.0% of Ir
Timers (0.000-60.000) s ± 0.5% ±10 ms
Inverse characteristics,see table 95, table 96 andtable 97
18 curve types See table 95, table 96 andtable 97
Second harmonic restrainoperation
(5–100)% of fundamental ± 2.0% of Ir
Relay characteristic angle (-180 to 180) degrees ± 2.0 degrees
Minimum polarizingvoltage
(1–100)% of UBase ± 0.5% of Ur
Minimum polarizingcurrent
(1-30)% of IBase ±0.25% of Ir
Real part of source Zused for currentpolarization
(0.50-1000.00) W/phase -
Imaginary part of sourceZ used for currentpolarization
(0.50–3000.00) W/phase -
Operate time, startfunction
25 ms typically at 0 to 2 x Iset -
Reset time, start function 25 ms typically at 2 to 0 x Iset -
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Impulse margin time 15 ms typically -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
56 ABB
Table 31. Four step negative sequence overcurrent protection NS4PTOC
Function Range or value Accuracy
Operate value, negativesequence current, step 1-4
(1-2500)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Timers (0.000-60.000) s ± 0.5% ± 10 ms
Inverse characteristics,see table 95, table 96 andtable 97
18 curve types See table 95, table 96 andtable 97
Minimum operate currentfor step 1 - 4
(1.00 - 10000.00)% of IBase ± 1.0% of Ir at I < Ir± 1.0% of I at I > Ir
Operate value, negativecurrent for directionalrelease
(1–100)% of IBase ± 1.0% of Ir
Relay characteristic angle (-180 to 180) degrees ± 2.0 degrees
Minimum polarizingvoltage
(1–100)% of UBase ± 0.5% of Ur
Minimum polarizingcurrent
(2-100)% of IBase ±1.0% of Ir
Real part of negativesequence sourceimpedance used forcurrent polarization
(0.50-1000.00) W/phase -
Imaginary part ofnegative sequence sourceimpedance used forcurrent polarization
(0.50–3000.00) W/phase -
Operate time, startfunction
25 ms typically at 0.5 to 2 x Iset -
Reset time, start function 25 ms typically at 2 to 0.5 x Iset -
Critical impulse time, startfunction
10 ms typically at 0 to 2 x Iset -
Impulse margin time,start function
15 ms typically -
Transient overreach <10% at τ = 100 ms -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 57
Table 32. Sensitive directional residual overcurrent and power protection SDEPSDE
Function Range or value Accuracy
Operate level for 3I0·cosjdirectional residualovercurrent
(0.25-200.00)% of lBase At low setting:(2.5-10) mA(10-50) mA
± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir ±0.5 mA±1.0 mA
Operate level for 3I0·3U0
· cosj directional residualpower
(0.25-200.00)% of SBase At low setting:(0.25-5.00)% of SBase
± 1.0% of Sr at S £ Sr
± 1.0% of S at S > Sr
± 10% of set value
Operate level for 3I0 and
j residual overcurrent
(0.25-200.00)% of lBase At low setting:(2.5-10) mA(10-50) mA
± 1.0% of Ir at £ Ir± 1.0% of I at I > Ir ±0.5 mA±1.0 mA
Operate level for non-directional overcurrent
(1.00-400.00)% of lBase At low setting:(10-50) mA
± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir ± 1.0 mA
Operate level for non-directional residualovervoltage
(1.00-200.00)% of UBase ± 0.5% of Ur at U£Ur
± 0.5% of U at U > Ur
Residual release currentfor all directional modes
(0.25-200.00)% of lBase At low setting:(2.5-10) mA(10-50) mA
± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir ±0.5 mA± 1.0 mA
Residual release voltagefor all directional modes
(0.01-200.00)% of UBase ± 0.5% of Ur at U£Ur
± 0.5% of U at U > Ur
Reset ratio > 95% -
Timers (0.000-60.000) s ± 0.5% ±10 ms
Inverse characteristics,see table 95, table 96 andtable 97
19 curve types See table 95, table 96 andtable 97
Relay characteristic angleRCA
(-179 to 180) degrees ± 2.0 degrees
Relay open angle ROA (0-90) degrees ± 2.0 degrees
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
58 ABB
Table 32. Sensitive directional residual overcurrent and power protection SDEPSDE,continued
Function Range or value Accuracy
Operate time, non-directional residual overcurrent
60 ms typically at 0 to 2 x Iset -
Reset time, non-directional residual overcurrent
60 ms typically at 2 to 0 x Iset -
Operate time, startfunction
150 ms typically at 0 to 2 x Iset -
Reset time, start function 50 ms typically at 2 to 0 x Iset -
Table 33. Thermal overload protection, one time constant LPTTR
Function Range or value Accuracy
Reference current (0-400)% of IBase ± 1.0% of Ir
Reference temperature (0-400)°C ± 1.0°C
Operate time:
2 2
2 2ln p
b
I It
I It
æ ö-ç ÷= ×ç ÷-è ø
EQUATION1356 V1 EN (Equation 1)
I = actual measuredcurrentIp = load current before
overload occursIb = base current, IBase
Time constant t = (0–1000) minutes
IEC 60255-8, class 5 + 200 ms
Alarm temperature (0-200)°C ± 2.0% of heat content trip
Trip temperature (0-400)°C ± 2.0% of heat content trip
Reset level temperature (0-400)°C ± 2.0% of heat content trip
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 59
Table 34. Thermal overload protection, two time constants TRPTTR
Function Range or value Accuracy
Base current 1 and 2 (30–250)% of IBase ± 1.0% of Ir
Operate time:
2 2
2 2ln p
b
I It
I It
æ ö-ç ÷= ×ç ÷-è ø
EQUATION1356 V1 EN (Equation 2)
I = Imeasured
Ip = load current before
overload occurs
Time constant τ = (1–500)minutes
IEC 60255–8, class 5 + 200 ms
Alarm level 1 and 2 (50–99)% of heat contenttrip value
± 2.0% of heat content trip
Operate current (50–250)% of IBase ± 1.0% of Ir
Reset level temperature (10–95)% of heat contenttrip
± 2.0% of heat content trip
Table 35. Breaker failure protection CCRBRF
Function Range or value Accuracy
Operate phase current (5-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio, phase current > 95% -
Operate residual current (2-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio, residual current > 95% -
Phase current level forblocking of contact function
(5-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Timers (0.000-60.000) s ± 0.5% ±10 ms
Operate time for currentdetection
10 ms typically -
Reset time for currentdetection
15 ms maximum -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
60 ABB
Table 36. Stub protection STBPTOC
Function Range or value Accuracy
Operating current (1-2500)% of IBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Definite time (0.000-60.000) s ± 0.5% ± 10 ms
Operating time, start function 20 ms typically at 0 to 2 x Iset -
Resetting time, startfunction 25 ms typically at 2 to 0 x Iset -
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Impulse margin time 15 ms typically -
Table 37. Pole discordance protection CCRPLD
Function Range or value Accuracy
Operate current (0–100)% of IBase ± 1.0% of Ir
Time delay (0.000-60.000) s ± 0.5% ± 10 ms
Table 38. Directional underpower protection GUPPDUP
Function Range or value Accuracy
Power level (0.0–500.0)% of SBase At low setting:(0.5-2.0)% of SBase(2.0-10)% of SBase
± 1.0% of Sr at S < Sr
± 1.0% of S at S > Sr
< ± 50% of set value< ± 20% of set value
Characteristic angle (-180.0–180.0) degrees 2 degrees
Timers (0.00-6000.00) s ± 0.5% ± 10 ms
Table 39. Directional overpower protection GOPPDOP
Function Range or value Accuracy
Power level (0.0–500.0)% of Sbase
At low setting:(0.5-2.0)% of Sbase
(2.0-10)% of Sbase
± 1.0% of Sr at S < Sr
± 1.0% of S at S > Sr
< ± 50% of set value< ± 20% of set value
Characteristic angle (-180.0–180.0) degrees 2 degrees
Timers (0.00-6000.00) s ± 0.5% ± 10 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 61
Table 40. Broken conductor check BRCPTOC
Function Range or value Accuracy
Minimum phase current foroperation
(5–100)% of IBase ± 0.1% of Ir
Unbalance current operation (0–100)% of maximumcurrent
± 0.1% of Ir
Timer (0.00-6000.00) s ± 0.5% ± 10 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
62 ABB
Table 41. Capacitor bank protection CBPGAPC
Function Range or value Accuracy
Operate value, overcurrent (0-900)% of lBase ± 1.0% of Ir at I < Ir± 1.0% of I at I > Ir
Reset ratio, overcurrent >95% -
Operate time, start 10 ms typically -
Reset time, start 30 ms typically -
Critical impulse time, overcurrentprotection start
2 ms typically at 0.5 to.2xIset1 ms typically at 0.5 to 10xIset
-
Impulse margin time, overcurrentprotection start
15 ms typically
Operate value, undercurrent (5-100)% of IBase ± 1.0% of Ir at I < Ir± 1.0% of I at I > Ir
Reset ratio, undercurrent <105% -
Operate value, reconnectioninhibit function
(4-1000)% of IBase ± 1.0% of Ir at I < Ir± 1.0% of I at I > Ir
Operate value, reactive poweroverload function
(5-900)% ± 1.0% of Sr at S < Sr
± 1.0% of S at S > Sr
Operate value, voltage protectionfunction for harmonic overload(Definite time)
(5-500)% ± 0.5% of Ur at U<Ur
± 0.5% of U at U>Ur
Operate value, voltage protectionfunction for harmonic overload(Inverse time)
(80-200)% ± 0.5% of Ur at U<Ur
± 0.5% of U at U>Ur
Inverse time characteristic According to IEC60871-1 (2005)and IEEE/ANSI C37.99 (2000)
Class 10 + 50 ms
Maximum trip delay, harmonicoverload IDMT
(0.05-6000.00) s ± 0.5% ± 10 ms
Minimum trip delay, harmonicoverload IDMT
(0.05-60.00) s ± 0.5% ± 10 ms
Timers (0.00-6000.00) s ± 0.5% ± 10 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 63
Voltage protection
Table 42. Two step undervoltage protection UV2PTUV
Function Range or value Accuracy
Operate voltage, low andhigh step
(1–100)% of UBase ± 0.5% of Ur
Absolute hysteresis (0–100)% of UBase ± 0.5% of Ur
Internal blocking level, lowand high step
(1–100)% of UBase ± 0.5% of Ur
Inverse time characteristicsfor low and high step, seetable 99
- See table 99
Definite time delays (0.000-60.000) s ± 0.5% ±10 ms
Minimum operate time,inverse characteristics
(0.000–60.000) s ± 0.5% ± 10 ms
Operate time, start function 25 ms typically at 2 to 0 x Uset -
Reset time, start function 25 ms typically at 0 to 2 x Uset -
Critical impulse time 10 ms typically at 1.2 to 0.8 x Uset -
Impulse margin time 15 ms typically -
Table 43. Two step overvoltage protection OV2PTOV
Function Range or value Accuracy
Operate voltage, low andhigh step
(1-200)% of UBase ± 0.5% of Ur at U < Ur
± 0.5% of U at U > Ur
Absolute hysteresis (0–100)% of UBase ± 0.5% of Ur at U < Ur
± 0.5% of U at U > Ur
Inverse time characteristicsfor low and high step, seetable 98
- See table 98
Definite time delays (0.000-60.000) s ± 0.5% ± 10 ms
Minimum operate time,Inverse characteristics
(0.000-60.000) s ± 0.5% ± 10 ms
Operate time, start function 25 ms typically at 0 to 2 x Uset -
Reset time, start function 25 ms typically at 2 to 0 x Uset -
Critical impulse time 10 ms typically at 0 to 2 x Uset -
Impulse margin time 15 ms typically -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
64 ABB
Table 44. Two step residual overvoltage protection ROV2PTOV
Function Range or value Accuracy
Operate voltage, low andhigh step
(1-200)% of UBase ± 0.5% of Ur at U < Ur
± 1.0% of U at U > Ur
Absolute hysteresis (0–100)% of UBase ± 0.5% of Ur at U < Ur
± 1.0% of U at U > Ur
Inverse time characteristicsfor low and high step, seetable 100
- See table 100
Definite time setting (0.000–60.000) s ± 0.5% ± 10 ms
Minimum operate time (0.000-60.000) s ± 0.5% ± 10 ms
Operate time, start function 25 ms typically at 0 to 2 x Uset -
Reset time, start function 25 ms typically at 2 to 0 x Uset -
Critical impulse time 10 ms typically at 0 to 2 x Uset -
Impulse margin time 15 ms typically -
Table 45. Voltage differential protection VDCPTOV
Function Range or value Accuracy
Voltage difference foralarm and trip
(0.0–100.0) % of UBase ± 0.5 % of Ur
Under voltage level (0.0–100.0) % of UBase ± 0.5% of Ur
Timers (0.000–60.000)s ± 0.5% ± 10 ms
Table 46. Loss of voltage check LOVPTUV
Function Range or value Accuracy
Operate voltage (0–100)% of UBase ± 0.5% of Ur
Pulse timer (0.050–60.000) s ± 0.5% ± 10 ms
Timers (0.000–60.000) s ± 0.5% ± 10 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 65
Frequency protection
Table 47. Underfrequency protection SAPTUF
Function Range or value Accuracy
Operate value, start function (35.00-75.00) Hz ± 2.0 mHz
Operate time, start function 100 ms typically -
Reset time, start function 100 ms typically -
Operate time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Reset time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Voltage dependent time delay
( )ExponentU UMin
t tMax tMin tMinUNom UMin
-= × - +
-é ùê úë û
EQUATION1182 V1 EN (Equation 3)
U=Umeasured
Settings:UNom=(50-150)% ofUbase
UMin=(50-150)% of Ubase
Exponent=0.0-5.0tMax=(0.000-60.000)stMin=(0.000-60.000)s
Class 5 + 200 ms
Table 48. Overfrequency protection SAPTOF
Function Range or value Accuracy
Operate value, start function (35.00-75.00) Hz ± 2.0 mHz atsymmetricalthree-phasevoltage
Operate time, start function 100 ms typically at fset -0.5 Hz to
fset +0.5 Hz
-
Reset time, start function 100 ms typically -
Operate time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Reset time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Table 49. Rate-of-change frequency protection SAPFRC
Function Range or value Accuracy
Operate value, start function (-10.00-10.00) Hz/s ± 10.0 mHz/s
Operate value, internal blockinglevel
(0-100)% of UBase ± 0.5% of Ur
Operate time, start function 100 ms typically -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
66 ABB
Multipurpose protection
Table 50. General current and voltage protection CVGAPC
Function Range or value Accuracy
Measuring current input phase1, phase2, phase3,PosSeq, NegSeq, 3*ZeroSeq,MaxPh, MinPh, UnbalancePh,phase1-phase2, phase2-phase3,phase3-phase1, MaxPh-Ph,MinPh-Ph, UnbalancePh-Ph
-
Base current (1 - 99999) A -
Measuring voltage input phase1, phase2, phase3,PosSeq, -NegSeq, -3*ZeroSeq,MaxPh, MinPh, UnbalancePh,phase1-phase2, phase2-phase3,phase3-phase1, MaxPh-Ph,MinPh-Ph, UnbalancePh-Ph
-
Base voltage (0.05 - 2000.00) kV -
Start overcurrent, step 1 and 2 (2 - 5000)% of IBase ± 1.0% of Ir for I<Ir± 1.0% of I for I>Ir
Start undercurrent, step 1and 2
(2 - 150)% of IBase ± 1.0% of Ir for I<Ir± 1.0% of I for I>Ir
Definite time delay (0.00 - 6000.00) s ± 0.5% ± 10 ms
Operate time startovercurrent
25 ms typically at 0 to 2 x Iset -
Reset time start overcurrent 25 ms typically at 2 to 0 x Iset -
Operate time startundercurrent
25 ms typically at 2 to 0 x Iset -
Reset time start undercurrent 25 ms typically at 0 to 2 x Iset -
See table 95 and table 96 Parameter ranges for customerdefined characteristic no 17:k: 0.05 - 999.00A: 0.0000 - 999.0000B: 0.0000 - 99.0000C: 0.0000 - 1.0000P: 0.0001 - 10.0000PR: 0.005 - 3.000TR: 0.005 - 600.000CR: 0.1 - 10.0
See table 95 and table 96
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 67
Table 50. General current and voltage protection CVGAPC , continued
Function Range or value Accuracy
Voltage level where voltagememory takes over
(0.0 - 5.0)% of UBase ± 0.5% of Ur
Start overvoltage, step 1 and 2 (2.0 - 200.0)% of UBase ± 0.5% of Ur for U<Ur
± 0.5% of U for U>Ur
Start undervoltage, step 1and 2
(2.0 - 150.0)% of UBase ± 0.5% of Ur for U<Ur
± 0.5% of U for U>Ur
Operate time, startovervoltage
25 ms typically at 0 to 2 x Uset -
Reset time, start overvoltage 25 ms typically at 2 to 0 x Uset -
Operate time startundervoltage
25 ms typically 2 to 0 x Uset -
Reset time start undervoltage 25 ms typically at 0 to 2 x Uset -
High and low voltage limit,voltage dependent operation
(1.0 - 200.0)% of UBase ± 1.0% of Ur for U<Ur
± 1.0% of U for U>Ur
Directional function Settable: NonDir, forward andreverse
-
Relay characteristic angle (-180 to +180) degrees ± 2.0 degrees
Relay operate angle (1 to 90) degrees ± 2.0 degrees
Reset ratio, overcurrent > 95% -
Reset ratio, undercurrent < 105% -
Reset ratio, overvoltage > 95% -
Reset ratio, undervoltage < 105% -
Overcurrent:
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Impulse margin time 15 ms typically -
Undercurrent:
Critical impulse time 10 ms typically at 2 to 0 x Iset -
Impulse margin time 15 ms typically -
Overvoltage:
Critical impulse time 10 ms typically at 0 to 2 x Uset -
Impulse margin time 15 ms typically -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
68 ABB
Table 50. General current and voltage protection CVGAPC , continued
Function Range or value Accuracy
Undervoltage:
Critical impulse time 10 ms typically at 2 to 0 x Uset -
Impulse margin time 15 ms typically -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 69
Secondary system supervision
Table 51. Current circuit supervision CCSRDIF
Function Range or value Accuracy
Operate current (5-200)% of Ir ± 10.0% of Ir at I £ Ir± 10.0% of I at I > Ir
Block current (5-500)% of Ir ± 5.0% of Ir at I £ Ir± 5.0% of I at I > Ir
Table 52. Fuse failure supervision SDDRFUF
Function Range or value Accuracy
Operate voltage, zero sequence (1-100)% of UBase ± 1.0% of Ur
Operate current, zero sequence (1–100)% of IBase ± 1.0% of Ir
Operate voltage, negativesequence
(1–100)% of UBase ± 0.5% of Ur
Operate current, negativesequence
(1–100)% of IBase ± 1.0% of Ir
Operate voltage change level (1–100)% of UBase ± 5.0% of Ur
Operate current change level (1–100)% of IBase ± 5.0% of Ir
Operate phase voltage (1-100)% of UBase ± 0.5% of Ur
Operate phase current (1-100)% of IBase ± 1.0% of Ir
Operate phase dead line voltage (1-100)% of UBase ± 0.5% of Ur
Operate phase dead line current (1-100)% of IBase ± 1.0% of Ir
Operate time, start function 25 ms typically at 1 to 0Ubase
-
Reset time, start function 35 ms typically at 0 to 1Ubase
-
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
70 ABB
Control
Table 53. Synchronizing, synchrocheck and energizing check SESRSYN
Function Range or value Accuracy
Phase shift, jline - jbus (-180 to 180) degrees -
Voltage ratio, Ubus/Uline (0.40-25.000) % ofUBaseBus and UBaseLIne
-
Voltage high limit for synchronizingand synchrocheck
(50.0-120.0)% ofUBaseBus and UBaseLIne
± 0.5% of Ur at U ≤ Ur
± 0.5% of U at U >Ur
Reset ratio, synchrocheck > 95% -
Frequency difference limit betweenbus and line
(0.003-1.000) Hz ± 2.0 mHz
Phase angle difference limitbetween bus and line
(5.0-90.0) degrees ± 2.0 degrees
Voltage difference limit betweenbus and line
(0.02-0.5) p.u ± 0.5% of Ur
Time delay output for synchrocheck (0.000-60.000) s ± 0.5% ± 10 ms
Voltage high limit for energizingcheck
(50.0-120.0)% ofUBaseBus and UBaseLIne
± 0.5% of Ur at U ≤ Ur
± 0.5% of U at U >Ur
Reset ratio, voltage high limit > 95% -
Voltage low limit for energizingcheck
(10.0-80.0)% of UBase ± 0.5% of Ur
Reset ratio, voltage low limit < 105% -
Maximum voltage for energizing (50.0-180.0)% ofUBaseBus and/orUBaseLIne
± 0.5% of Ur at U ≤ Ur
± 0.5% of U at U >Ur
Time delay for energizing check (0.000-60.000) s ± 0.5% ± 10 ms
Operate time for synchrocheckfunction
160 ms typically -
Operate time for energizing function 80 ms typically -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 71
Table 54. Autorecloser SMBRREC
Function Range or value Accuracy
Number of autoreclosing shots 1 - 5 -
Autoreclosing open time:shot 1 - t1 1Phshot 1 - t1 2Phshot 1 - t1 3PhHSshot 1 - t1 3PhDld
(0.000-60.000) s
± 0.5% ± 10 ms
shot 2 - t2shot 3 - t3shot 4 - t4shot 5 - t5
(0.00-6000.00) s
Extended autorecloser open time (0.000-60.000) s
Autorecloser maximum wait time for sync (0.00-6000.00) s
Maximum trip pulse duration (0.000-60.000) s
Inhibit reset time (0.000-60.000) s
Reclaim time (0.00-6000.00) s
Minimum time CB must be closed before ARbecomes ready for autoreclosing cycle
(0.00-6000.00) s
Circuit breaker closing pulse length (0.000-60.000) s
CB check time before unsuccessful (0.00-6000.00) s
Wait for master release (0.00-6000.00) s
Wait time after close command beforeproceeding to next shot
(0.000-60.000) s
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
72 ABB
Table 55. Voltage control TR1ATCC, TR8ATCC, TCMYLTC and TLCYLTC
Function Range or value Accuracy
Transformer reactance (0.1–200.0)Ω, primary -
Time delay for lower commandwhen fast step down mode isactivated
(1.0–100.0) s -
Voltage control set voltage (85.0–120.0)% of UB ±0.25% of Ur
Outer voltage deadband (0.2–9.0)% of UB -
Inner voltage deadband (0.1–9.0)% of UB -
Upper limit of busbar voltage (80–180)% of UB ± 1.0% of Ur
Lower limit of busbar voltage (70–120)% of UB ± 1.0% of Ur
Undervoltage block level (0–120)% of UB ± 1.0% of Ur
Time delay (long) for automaticcontrol commands
(3–1000) s ± 0.5% ± 10 ms
Time delay (short) for automaticcontrol commands
(1–1000) s ± 0.5% ± 10 ms
Minimum operating time in inversemode
(3–120) s ± 0.5% ± 10 ms
Line resistance (0.00–150.00)Ω, primary -
Line reactance (-150.00–150.00)Ω, primary -
Load voltage adjustment constants (-20.0–20.0)% of UB -
Load voltage auto correction (-20.0–20.0)% of UB -
Duration time for the reverse actionblock signal
(30–6000) s ± 0.5% ± 10 ms
Current limit for reverse actionblock
(0–100)% of I1Base -
Overcurrent block level (0–250)% of I1Base ± 1.0% of Ir at I≤Ir± 1.0% of I at I>Ir
Level for number of counted raise/lower within one hour
(0–30) operations/hour -
Level for number of counted raise/lower within 24 hours
(0–100) operations/day -
Time window for hunting alarm (1–120) minutes -
Hunting detection alarm, maxoperations/window
(3–30) operations/window -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 73
Table 55. Voltage control TR1ATCC, TR8ATCC, TCMYLTC and TLCYLTC, continued
Function Range or value Accuracy
Alarm level of active power inforward and reverse direction
(-9999.99–9999.99) MW ± 1.0% of Sr
Alarm level of reactive power inforward and reverse direction
(-9999.99–9999.99) MVAr ± 1.0% of Sr
Time delay for alarms from powersupervision
(1–6000) s ± 0.5% ± 10 ms
Tap position for lowest and highestvoltage
(1–63) -
mA for lowest and highest voltagetap position
(0.000–25.000) mA -
Type of code conversion BIN, BCD, GRAY, SINGLE, mA -
Time after position change beforethe value is accepted
(1–60) s ± 0.5% ± 10 ms
Tap changer constant time-out (1–120) s ± 0.5% ± 10 ms
Raise/lower command output pulseduration
(0.5–10.0) s ± 0.5% ± 10 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
74 ABB
Scheme communication
Table 56. Scheme communication logic for distance or overcurrent protection ZCPSCH
Function Range or value Accuracy
Scheme type IntertripPermissive UnderreachPermissive OverreachBlocking
-
Co-ordination time forblocking communicationscheme
(0.000-60.000) s ± 0.5% ± 10 ms
Minimum duration of a sendsignal
(0.000-60.000) s ± 0.5% ± 10 ms
Security timer for loss ofguard signal detection
(0.000-60.000) s ± 0.5% ± 10 ms
Operation mode ofunblocking logic
OffNoRestartRestart
-
Table 57. Current reversal and weak-end infeed logic for distance protectionZCRWPSCH
Function Range or value Accuracy
Detection level phase-to-neutral voltage
(10-90)% of UBase ± 0.5% of Ur
Detection level phase-to-phase voltage
(10-90)% of UBase ± 0.5% of Ur
Reset ratio <105% -
Operate time for currentreversal logic
(0.000-60.000) s ± 0.5% ± 10 ms
Delay time for currentreversal
(0.000-60.000) s ± 0.5% ± 10 ms
Coordination time forweak-end infeed logic
(0.000-60.000) s ± 0.5% ± 10 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 75
Table 58. Scheme communication logic for residual overcurrent protection ECPSCH
Function Range or value Accuracy
Scheme type Permissive UnderreachingPermissive OverreachingBlocking
-
Communication schemecoordination time
(0.000-60.000) s ± 0.5% ± 10 ms
Table 59. Current reversal and weak-end infeed logic for residual overcurrent protectionECRWPSCH
Function Range or value Accuracy
Operating mode of WEIlogic
OffEchoEcho & Trip
-
Operate voltage 3Uo for
WEI trip
(5-70)% of UBase ± 0.5% of Ur
Reset ratio >95% -
Operate time for currentreversal logic
(0.000-60.000) s ± 0.5% ± 10 ms
Delay time for currentreversal
(0.000-60.000) s ± 0.5% ± 10 ms
Coordination time forweak-end infeed logic
(0.000–60.000) s ± 0.5% ± 10 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
76 ABB
Logic
Table 60. Tripping logic SMPPTRC
Function Range or value Accuracy
Trip action 3-ph, 1/3-ph, 1/2/3-ph -
Minimum trip pulse length (0.000-60.000) s ± 0.5% ± 10 ms
Timers (0.000-60.000) s ± 0.5% ± 10 ms
Table 61. Configurable logic blocks
Logic block Quantity with cycle time Range or value Accuracy
fast medium normal
LogicAND 60 60 160 - -
LogicOR 60 60 160 - -
LogicXOR 10 10 20 - -
LogicInverter 30 30 80 - -
LogicSRMemory 10 10 20 - -
LogicRSMemory 10 10 20 - -
LogicGate 10 10 20 - -
LogicTimer 10 10 20 (0.000–90000.000) s ± 0.5% ± 10 ms
LogicPulseTimer 10 10 20 (0.000–90000.000) s ± 0.5% ± 10 ms
LogicTimerSet 10 10 20 (0.000–90000.000) s ± 0.5% ± 10 ms
LogicLoopDelay 10 10 20 (0.000–90000.000) s ± 0.5% ± 10 ms
Trip Matrix Logic 6 6 - - -
Boolean 16 toInteger
4 4 8 - -
Boolean 16 tointeger withLogic Node
4 4 8 - -
Integer toBoolean 16
4 4 8 - -
Integer toBoolean 16 withLogic Node
4 4 8 - -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 77
Table 62. Configurable logic blocks Q/T
Logic block Quantity withcycle time
Range or value Accuracy
medium normal
ANDQT 20 100 - -
ORQT 20 100 - -
INVERTERQT 20 100 - -
XORQT 10 30 - -
SRMEMORYQT 10 30 - -
RSMEMORYQT 10 30 - -
TIMERSETQT 10 30 (0.000-90000.000) s ± 0.5% ± 10 ms
PULSETIMERQT 10 30 (0.000-90000.000) s ± 0.5% ± 10 ms
INVALIDQT 6 6 - -
INDCOMBSPQT 10 10 - -
INDEXTSPQT 10 10 - -
Table 63. Extension logic package
Logic block Quantity with cycle time Range or value Accuracy
fast medium normal
LogicAND 40 40 100 - -
LogicXOR - - 49 - -
LogicSRMemory - - 110 - -
LogicTimer 5 5 49 (0.000–90000.000) s ± 0.5% ± 10 ms
LogicPulseTimer 5 5 49 (0.000–90000.000) s ± 0.5% ± 10 ms
Trip matrix logic - - 18 - -
SLGGIO 10 10 54 - -
VSGGIO 10 10 10 - -
LogicOR 40 40 100 - -
LogicGate - - 49 - -
LogicTimerSet - - 49 - -
LogicLoopDelay - - 49 - -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
78 ABB
Monitoring
Table 64. Measurements CVMMXN
Function Range or value Accuracy
Frequency (0.95-1.05) × fr ± 2.0 mHz
Voltage (0.1-1.5) ×Ur ± 0.5% of Ur at U£Ur
± 0.5% of U at U > Ur
Connected current (0.2-4.0) × Ir ± 0.5% of Ir at I £ Ir± 0.5% of I at I > Ir
Active power, P 0.1 x Ur< U < 1.5 x Ur
0.2 x Ir < I < 4.0 x Ir
± 1.0% of Sr at S ≤ Sr
± 1.0% of S at S > Sr
Conditions:0.8 x Ur < U < 1.2 Ur
0.2 x Ir < I < 1.2 Ir
Reactive power, Q 0.1 x Ur< U < 1.5 x Ur
0.2 x Ir < I < 4.0 x Ir
Apparent power, S 0.1 x Ur < U < 1.5 x Ur
0.2 x Ir< I < 4.0 x Ir
Power factor, cos (φ) 0.1 x Ur < U < 1.5 x Ur
0.2 x Ir< I < 4.0 x Ir
± 0.02
Table 65. Supervision of mA input signals
Function Range or value Accuracy
mA measuring function ± 5, ± 10, ± 20 mA0-5, 0-10, 0-20, 4-20 mA
± 0.1 % of set value ± 0.005 mA
Max current oftransducer to input
(-20.00 to +20.00) mA
Min current oftransducer to input
(-20.00 to +20.00) mA
Alarm level for input (-20.00 to +20.00) mA
Warning level for input (-20.00 to +20.00) mA
Alarm hysteresis forinput
(0.0-20.0) mA
Table 66. Event counter CNTGGIO
Function Range or value Accuracy
Counter value 0-10000 -
Max. count up speed 10 pulses/s -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 79
Table 67. Disturbance report DRPRDRE
Function Range or value Accuracy
Pre-fault time (0.05–9.90) s -
Post-fault time (0.1–10.0) s -
Limit time (0.5–10.0) s -
Maximum number of recordings 100, first in - first out -
Time tagging resolution 1 ms See table 91
Maximum number of analog inputs 30 + 10 (external +internally derived)
-
Maximum number of binary inputs 96 -
Maximum number of phasors in the TripValue recorder per recording
30 -
Maximum number of indications in adisturbance report
96 -
Maximum number of events in the Eventrecording per recording
150 -
Maximum number of events in the Eventlist
1000, first in - first out -
Maximum total recording time (3.4 srecording time and maximum number ofchannels, typical value)
340 seconds (100recordings) at 50 Hz, 280seconds (80 recordings)at 60 Hz
-
Sampling rate 1 kHz at 50 Hz1.2 kHz at 60 Hz
-
Recording bandwidth (5-300) Hz -
Table 68. Fault locator LMBRFLO
Function Value or range Accuracy
Reactive and resistivereach
(0.001-1500.000) Ω/phase ± 2.0% static accuracy± 2.0% degrees static angularaccuracyConditions:Voltage range: (0.1-1.1) x Ur
Current range: (0.5-30) x Ir
Phase selection According to input signals -
Maximum number of faultlocations
100 -
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
80 ABB
Table 69. Event list
Function Value
Buffer capacity Maximum number of events inthe list
1000
Resolution 1 ms
Accuracy Depending on timesynchronizing
Table 70. Indications
Function Value
Buffer capacity Maximum number of indications presentedfor single disturbance
96
Maximum number of recorded disturbances 100
Table 71. Event recorder
Function Value
Buffer capacity Maximum number of events in disturbance report 150
Maximum number of disturbance reports 100
Resolution 1 ms
Accuracy Depending ontimesynchronizing
Table 72. Trip value recorder
Function Value
Buffer capacity
Maximum number of analog inputs 30
Maximum number of disturbance reports 100
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 81
Table 73. Disturbance recorder
Function Value
Buffer capacity Maximum number of analog inputs 40
Maximum number of binary inputs 96
Maximum number of disturbance reports 100
Maximum total recording time (3.4 s recording time andmaximum number of channels, typical value)
340 seconds (100 recordings)at 50 Hz280 seconds (80 recordings) at60 Hz
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
82 ABB
Metering
Table 74. Pulse counter PCGGIO
Function Setting range Accuracy
Input frequency See Binary Input Module (BIM) -
Cycle time for report ofcounter value
(1–3600) s -
Table 75. Energy metering ETPMMTR
Function Range or value Accuracy
Energy metering kWh Export/Import,kvarh Export/Import
Input from MMXU. No extra errorat steady load
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 83
Station communication
Table 76. IEC 61850-8-1 communication protocol
Function Value
Protocol IEC 61850-8-1
Communication speed for the IEDs 100BASE-FX
Table 77. LON communication protocol
Function Value
Protocol LON
Communication speed 1.25 Mbit/s
Table 78. SPA communication protocol
Function Value
Protocol SPA
Communication speed 300, 1200, 2400, 4800, 9600, 19200 or 38400 Bd
Slave number 1 to 899
Table 79. IEC60870-5-103 communication protocol
Function Value
Protocol IEC 60870-5-103
Communication speed 9600, 19200 Bd
Table 80. SLM – LON port
Quantity Range or value
Optical connector Glass fibre: type STPlastic fibre: type HFBR snap-in
Fibre, optical budget Glass fibre: 11 dB (1000 m typically *)Plastic fibre: 7 dB (10 m typically *)
Fibre diameter Glass fibre: 62.5/125 mmPlastic fibre: 1 mm
*) depending on optical budget calculation
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
84 ABB
Table 81. SLM – SPA/IEC 60870-5-103/DNP3 port
Quantity Range or value
Optical connector Glass fibre: type STPlastic fibre: type HFBR snap-in
Fibre, optical budget Glass fibre: 11 dB (3000ft/1000 m typically *)Plastic fibre: 7 dB (80ft/25 m typically *)
Fibre diameter Glass fibre: 62.5/125 mmPlastic fibre: 1 mm
*) depending on optical budget calculation
Table 82. Galvanic RS485 communication module
Quantity Range or value
Communication speed 2400–19200 bauds
External connectors RS-485 6-pole connectorSoft ground 2-pole connector
Table 83. Duo driver configuration DUODRV
Function Value
Protocol IEC 61850-8-1
Communication speed 100 Base-FX
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 85
Remote communication
Table 84. Line data communication module
Characteristic Range or value
Type of LDCM Short range(SR)
Medium range(MR)
Long range (LR)
Type of fibre Graded-indexmultimode62.5/125 µmor 50/125 µm
Singlemode9/125 µm
Singlemode 9/125 µm
Wave length 850 nm 1310 nm 1550 nm
Optical budgetGraded-index multimode62.5/125 mm, Graded-index multimode50/125 mm
13 dB (typicaldistanceabout 3 km *)9 dB (typicaldistanceabout 2 km *)
22 dB (typicaldistance 80 km *)
26 dB (typical distance110 km *)
Optical connector Type ST Type FC/PC Type FC/PC
Protocol C37.94 C37.94implementation**)
C37.94 implementation **)
Data transmission Synchronous Synchronous Synchronous
Transmission rate / Data rate 2 Mb/s / 64kbit/s
2 Mb/s / 64 kbit/s
2 Mb/s / 64 kbit/s
Clock source Internal orderived fromreceivedsignal
Internal orderived fromreceived signal
Internal or derived fromreceived signal
*) depending on optical budget calculation**) C37.94 originally defined just for multimode; using same header, configuration and dataformat as C37.94
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
86 ABB
Hardware
IED
Table 85. Case
Material Steel sheet
Front plate Steel sheet profile with cut-out for HMI
Surface treatment Aluzink preplated steel
Finish Light grey (RAL 7035)
Table 86. Water and dust protection level according to IEC 60529
Front IP40 (IP54 with sealing strip)
Rear, sides, topand bottom
IP20
Table 87. Weight
Case size Weight
6U, 1/2 x 19” £ 10 kg
6U, 3/4 x 19” £ 15 kg
6U, 1/1 x 19” £ 18 kg
Connection system
Table 88. CT and VT circuit connectors
Connector type Rated voltage andcurrent
Maximum conductorarea
Screw compression type 250 V AC, 20 A 4 mm2 (AWG12)
2 x 2.5 mm2 (2 x AWG14)
Terminal blocks suitable for ringlug terminals
250 V AC, 20 A 4 mm2 (AWG12)
Table 89. Binary I/O connection system
Connector type Rated voltage Maximum conductorarea
Screw compression type 250 V AC 2.5 mm2 (AWG14)
2 × 1 mm2 (2 x AWG18)
Terminal blocks suitable for ringlug terminals
300 V AC 3 mm2 (AWG14)
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 87
Basic IED functions
Table 90. Self supervision with internal event list
Data Value
Recording manner Continuous, event controlled
List size 1000 events, first in-first out
Table 91. Time synchronization, time tagging
Function Value
Time tagging resolution, events and sampled measurement values 1 ms
Time tagging error with synchronization once/min (minute pulsesynchronization), events and sampled measurement values
± 1.0 ms typically
Time tagging error with SNTP synchronization, sampledmeasurement values
± 1.0 ms typically
Table 92. GPS time synchronization module (GTM)
Function Range or value Accuracy
Receiver – ±1µs relative UTC
Time to reliable time reference withantenna in new position or after powerloss longer than 1 month
<30 minutes –
Time to reliable time reference after apower loss longer than 48 hours
<15 minutes –
Time to reliable time reference after apower loss shorter than 48 hours
<5 minutes –
Table 93. GPS – Antenna and cable
Function Value
Max antenna cable attenuation 26 db @ 1.6 GHz
Antenna cable impedance 50 ohm
Lightning protection Must be provided externally
Antenna cable connector SMA in receiver endTNC in antenna end
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
88 ABB
Table 94. IRIG-B
Quantity Rated value
Number of channels IRIG-B 1
Number of channels PPS 1
Electrical connector IRIG-B BNC
Optical connector PPS and IRIG-B Type ST
Type of fibre 62.5/125 μm multimode fibre
Pulse-width modulated 5 Vpp
Amplitude modulated– low level– high level
1-3 Vpp3 x low level, max 9 Vpp
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 89
Inverse characteristic
Table 95. ANSI Inverse time characteristics
Function Range or value Accuracy
Operating characteristic:
( )1= + ×
-
æ öç ÷ç ÷è ø
P
At B k
I
EQUATION1249-SMALL V1 EN
Reset characteristic:
( )2 1= ×
-
trt kI
EQUATION1250-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01unless otherwise stated
-
ANSI Extremely Inverse A=28.2, B=0.1217, P=2.0 , tr=29.1 ANSI/IEEE C37.112,class 5 + 40 ms
ANSI Very inverse A=19.61, B=0.491, P=2.0 , tr=21.6
ANSI Normal Inverse A=0.0086, B=0.0185, P=0.02, tr=0.46
ANSI Moderately Inverse A=0.0515, B=0.1140, P=0.02, tr=4.85
ANSI Long Time ExtremelyInverse
A=64.07, B=0.250, P=2.0, tr=30
ANSI Long Time Very Inverse A=28.55, B=0.712, P=2.0, tr=13.46
ANSI Long Time Inverse k=(0.05-999) in steps of 0.01A=0.086, B=0.185, P=0.02, tr=4.6
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
90 ABB
Table 96. IEC Inverse time characteristics
Function Range or value Accuracy
Operating characteristic:
( )1= ×
-
æ öç ÷ç ÷è ø
P
At k
I
EQUATION1251-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01 -
Time delay to reset, IEC inversetime
(0.000-60.000) s ± 0.5% of set time ±10 ms
IEC Normal Inverse A=0.14, P=0.02 IEC 60255-3, class 5+ 40 ms
IEC Very inverse A=13.5, P=1.0
IEC Inverse A=0.14, P=0.02
IEC Extremely inverse A=80.0, P=2.0
IEC Short time inverse A=0.05, P=0.04
IEC Long time inverse A=120, P=1.0
Programmable characteristicOperate characteristic:
( )= + ×
-
æ öç ÷ç ÷è ø
P
At B k
I C
EQUATION1370-SMALL V1 EN
Reset characteristic:
( )= ×
-PR
TRt k
I CR
EQUATION1253-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01A=(0.005-200.000) in steps of 0.001B=(0.00-20.00) in steps of 0.01C=(0.1-10.0) in steps of 0.1P=(0.005-3.000) in steps of 0.001TR=(0.005-100.000) in steps of 0.001CR=(0.1-10.0) in steps of 0.1PR=(0.005-3.000) in steps of 0.001
IEC 60255, class 5 +40 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 91
Table 97. RI and RD type inverse time characteristics
Function Range or value Accuracy
RI type inverse characteristic
1
0.2360.339
= ×
-
t k
I
EQUATION1137-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01 IEC 60255-3, class 5+ 40 ms
RD type logarithmic inversecharacteristic
5.8 1.35= - ×æ öç ÷è ø
tI
Ink
EQUATION1138-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01 IEC 60255-3, class 5+ 40 ms
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
92 ABB
Table 98. Inverse time characteristics for overvoltage protection
Function Range or value Accuracy
Type A curve:
=- >
>
æ öç ÷è ø
tk
U U
U
EQUATION1436-SMALL V1 EN
U> = Uset
U = Umeasured
k = (0.05-1.10) in steps of0.01 unless otherwise stated
Class 5 +40 ms
Type B curve:
2.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1437-SMALL V1 EN
k = (0.05-1.10) in steps of0.01 unless otherwise stated
Type C curve:
3.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1438-SMALL V1 EN
k = (0.05-1.10) in steps of0.01 unless otherwise stated
Programmable curve:
×= +
- >× -
>
æ öç ÷è ø
P
k At D
U UB C
U
EQUATION1439-SMALL V1 EN
k = (0.05-1.10) in steps of0.01 unless otherwise statedA = (0.005-200.000) in stepsof 0.001B = (0.50-100.00) in steps of0.01C = (0.0-1.0) in steps of 0.1D = (0.000-60.000) in stepsof 0.001P = (0.000-3.000) in steps of0.001
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 93
Table 99. Inverse time characteristics for undervoltage protection
Function Range or value Accuracy
Type A curve:
=< -
<
æ öç ÷è ø
kt
U U
U
EQUATION1431-SMALL V1 EN
U< = Uset
U = UVmeasured
k = (0.05-1.10) in steps of0.01 unless otherwise stated
Class 5 +40 ms
Type B curve:
2.0
4800.055
32 0.5
×= +
< -× -
<
æ öç ÷è ø
kt
U U
U
EQUATION1432-SMALL V1 EN
U< = Uset
U = Umeasured
k = (0.05-1.10) in steps of0.01 unless otherwise stated
Programmable curve:
×= +
< -× -
<
é ùê úê úê úæ öê úç ÷ë è ø û
P
k At D
U UB C
U
EQUATION1433-SMALL V1 EN
U< = Uset
U = Umeasured
k = (0.05-1.10) in steps of0.01 unless otherwise statedA = (0.005-200.000) in stepsof 0.001B = (0.50-100.00) in steps of0.01C = (0.0-1.0) in steps of 0.1D = (0.000-60.000) in stepsof 0.001P = (0.000-3.000) in steps of0.001
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
94 ABB
Table 100. Inverse time characteristics for residual overvoltage protection
Function Range or value Accuracy
Type A curve:
=- >
>
æ öç ÷è ø
tk
U U
U
EQUATION1436-SMALL V1 EN
U> = Uset
U = Umeasured
k = (0.05-1.10) insteps of 0.01
Class 5 +40 ms
Type B curve:
2.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1437-SMALL V1 EN
k = (0.05-1.10) insteps of 0.01
Type C curve:
3.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1438-SMALL V1 EN
k = (0.05-1.10) insteps of 0.01
Programmable curve:
×= +
- >× -
>
æ öç ÷è ø
P
k At D
U UB C
U
EQUATION1439-SMALL V1 EN
k = (0.05-1.10) insteps of 0.01A = (0.005-200.000)in steps of 0.001B = (0.50-100.00) insteps of 0.01C = (0.0-1.0) insteps of 0.1D = (0.000-60.000)in steps of 0.001P = (0.000-3.000) insteps of 0.001
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 95
21. Ordering
Guidelines
Carefully read and follow the set of rules to ensure problem-free order management. Be aware that certainfunctions can only be ordered in combination with other functions and that some functions require specifichardware selections.
Please refer to the available functions table for included application functions.
Product specification
Basic IED 670 platform and common functions housed in selected casing
REC670 Quantity: 1MRK 002 814-AC
Default:
The IED connect CD contains configuration alternative. Use the PCM600 to create or modify the configuration. ThePCM600 can also be used for adaptation of an included example configuration.
Option:
Customer specific configuration On request
Connection type for Power supply modules and I/O modules
Rule: Same connection type for Power supply modules and I/O modules must be ordered
Compression terminals 1MRK 002 960-AA
Ring lug terminals 1MRK 002 960-BA
Power supply module
Rule: One Power supply module must be specified
Power supply module (PSM) 24-60 VDC 1MRK 002 239-AB
90-250 VDC 1MRK 002 239-BB
Logic
Rule: One Tripping logic must be ordered
Tripping logic (SMPPTRC) Qty: 1 2 3 4 5 6 1MRK 002 917-AC
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
96 ABB
Control
Rule: One Apparatus control must be ordered
Apparatus control for single bay, max 8 apparatuses (1CB) incl. interlocking (APC8) 1MRK 002 916-GD
Apparatus control for single bay, max 15 apparatuses (2CBs) incl. interlocking (APC15) 1MRK 002 916-HD
Apparatus control for up to 6 bays, max 30 apparatuses (6CBs) incl. interlocking (APC30) 1MRK 002 916-RD
Optional functions
Differential protection
1Ph High impedance differential protection (HZPDIF)
Qty:
1 2 3 4 5 6 1MRK 002 901-HB
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 97
Current protection
Instantaneous phase overcurrent protection (PHPIOC)
Qty:
1 2 3 4 5 6 1MRK 002 906-AC
Four step phase overcurrent protection (OC4PTOC)
Qty:
1 2 3 4 5 6 1MRK 002 906-BD
Instantaneous residual overcurrent protection (EFPIOC)
Qty:
1 2 3 4 5 6 1MRK 002 906-CC
Four step residual overcurrent protection (EF4PTOC)
Qty:
1 2 3 4 5 6 1MRK 002 906-DD
Four step directional negative phase sequenceovercurrent protection (NS4PTOC)
Qty:
1 2 3 1MRK 002 906-DM
Sensitive directional residual overcurrent and powerprotection (SDEPSDE)
Qty:
1 2 3 4 5 6 1MRK 002 907-DC
Thermal overload protection, one time constant (LPTTR)
Qty:
1 2 1MRK 002 906-LD
Thermal overload protection, two time constants(TRPTTR)
Qty:
1 2 1MRK 002 906-NC
Breaker failure protection (CCRBRF)
Qty:
1 2 3 4 5 6 1MRK 002 906-RC
Stub protection (STBPTOC) Qty: 1MRK 002 906-ZC
Pole discordance protection (CCRPLD)
Qty:
1 2 3 1MRK 002 907-AC
Directional underpower protection (GUPPDUP)
Qty:
1 2 1MRK 002 902-FB
Directional overpower protection (GOPPDUP)
Qty:
1 2 1MRK 002 902-GB
Broken conductor check (BRCPTOC) Qty: 1MRK 002 902-DB
Capacitor bank protection (CBPGAPC)
Qty:
1 2 3 1MRK 002 902-MA
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
98 ABB
Voltage protection
Two step undervoltage protection (UV2PTUV)
Qty:
1 2 1MRK 002 908-AC
Two step overvoltage protection (OV2PTOV)
Qty:
1 2 1MRK 002 908-DC
Two step residual overvoltage protection (ROV2PTOV)
Qty:
1 2 1MRK 002 908-GC
Voltage differential protection (VDCPTOV)
Qty:
1 2 3 4 5 6 1MRK 002 924-TB
Loss of voltage check (LOVPTUV)
Qty:
1 2 1MRK 002 902-EB
Frequency protection
Underfrequency protection (SAPTUF)
Qty:
1 2 3 4 5 6 1MRK 002 908-NC
Overfrequency protection (SAPTOF)
Qty:
1 2 3 4 5 6 1MRK 002 908-RC
Rate-of-change frequency protection (SAPFRC)
Qty:
1 2 3 4 5 6 1MRK 002 908-SB
Multipurpose protection
General current and voltage protection (CVGAPC)
Qty:
1 2 3 4 5
6 7 8 9
1MRK 002 902-AB
Secondary system supervision
Current circuit supervision (CCSRDIF)
Qty:
1 2 3 4 5 1MRK 002 914-AB
Fuse failure supervision (SDDRFUF)
Qty:
1 2 3 4 1MRK 002 914-GC
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 99
Control
Synchrocheck, energizing check and synchronizing(SESRSYN)Rule: Can only be ordered with Apparatus control APC8/APC15
Qty:
1 2 1MRK 002 916-AD
Synchrocheck, energizing check and synchronizing(SESRSYN)Rule: Can only be ordered with Apparatus control APC30
Qty:
1 2 3 4 5 6 1MRK 002 916-SD
Autorecloser (SMBRREC)Rule: Can only be ordered with Apparatus control APC8/APC15
Qty:
1 2 3 4 1MRK 002 916-EB
Autorecloser (SMBRREC)Rule: Can only be ordered with Apparatus control APC30
Qty:
1 2 3 4 5 6 1MRK 002 916-TB
Rule: Only one of (TR1ATCC, TR8ATCC) can be ordered.If TR1ATCC or TR8ATCC is ordered then one ofTCMYLTC or TCLYLTC must be ordered.Automatic voltage control for tapchanger, singletransformer (TR1ATCC)
Qty:
1 2 3 4 1MRK 002 916-YC
Automatic voltage control for tapchanger, parallelcontrol (TR8ATCC)
Qty:
1 2 3 4 1MRK 002 916-ZC
Tap changer control and supervision, 6 binary inputs,coded binary (Binary, BCD, Gray) (TCMYLTC)
Qty:
1 2 3 4 1MRK 002 925-PC
Tap changer control and supervision, 32 binary inputs,one per position (TCLYLTC)
Qty:
1 2 3 4 1MRK 002 924-UB
Scheme communication
Scheme communication logic for distance protection or overcurrent protection(ZCPSCH)
1MRK 002 904-RA
Current reversal and weak end infeed logic for distance protection (ZCRWPSCH) 1MRK 002 904-SB
Local acceleration logic (ZCLCPLAL) 1MRK 002 904-VC
Scheme communication logic for residual overcurrent protection (ECPSCH) 1MRK 002 906-GA
Current reversal and weak end infeed logic for residual overcurrent protection(ECRWPSCH)
1MRK 002 906-HB
Logic
Configurable logic blocks Q/T Qty: 1MRK 002 917-ML
Extension logic package Qty: 1MRK 002 917-MD
Monitoring
Fault locator (LMBRFLO) 1MRK 002 918-BB
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
100 ABB
Station communication
Duo driver configuration (DUODRV) 1MRK 002 924-YA
First local HMI user dialogue language
Rule: One must be ordered
HMI language, English IEC 1MRK 002 930-AA
HMI language, English US 1MRK 002 930-BA
Additional local HMI user dialogue language
Rule: Maximum one alternative
HMI language, German 1MRK 002 920-AB
HMI language, Spanish 1MRK 002 920-DB
HMI language, Swedish 1MRK 002 920-KB
Optional hardware
Human machine hardware interface
Rule: One must be ordered. “Medium size - graphic display” HMI is required inorder to be able to give Raise/Lower commands, in the manual operating mode, tothe OLTC from IED 670 via Voltage control (VCTR) function.
Display type Keypad symbol Case size
Small, alpha numeric IEC 1/2 19" 1MRK 000 008-HB
Small, alpha numeric IEC 3/4 19" 1MRK 000 008-PB
Small, alpha numeric IEC 1/1 19" 1MRK 000 008-KB
Medium, graphic display IEC 1/2 19" 1MRK 000 008-LB
Medium, graphic display IEC 1/1 19" 1MRK 000 008-MB
Medium, graphic display IEC 3/4 19" 1MRK 000 008-NB
Medium, graphic display ANSI 1/2 19" 1MRK 000 008-LC
Medium, graphic display ANSI 3/4 19" 1MRK 000 008-NC
Medium, graphic display ANSI 1/1 19" 1MRK 000 008-MC
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 101
Analog system
Note: The same type of connection terminals has to be ordered for both TRMs
Transformer input module, compression terminals 12I, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CG
Transformer input module, compression terminals 12I, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CH
Transformer input module, compression terminals 9I+3U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-BG
Transformer input module, compression terminals 9I+3U, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-BH
Transformer input module, compression terminals 5I, 1A+4I, 5A+3U,50/60 Hz
Qty:
1 2 1MRK 002 247-BK
Transformer input module, compression terminals 7I+5U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AP
Transformer input module, compression terminals 7I+5U, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AR
Transformer input module, compression terminals 6I, 5A+1I, 1A+5U,50/60 Hz
Qty:
1 2 1MRK 002 247-AU
Transformer input module, compression terminals 3I, 5A+4I, 1A+5U,50/60 Hz
Qty:
1 2 1MRK 002 247-AV
Transformer input module, compression terminals 3IM, 1A+4IP, 1A+5U,50/60 Hz
Qty: 1 2 1MRK 002 247-EA
Transformer input module, compression terminals 3IM, 5A+4IP, 5A+5U,50/60 Hz
Qty: 1 2 1MRK 002 247-EB
Transformer input module, compression terminals 6I+6U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AG
Transformer input module, compression terminals 6I+6U, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AH
Transformer input module, compression terminals 3I, 5A+3I, 1A+6U,50/60 Hz
Qty:
1 2 1MRK 002 247-AE
Transformer input module, compression terminals 6I, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-DG
Transformer input module, compression terminals 6I, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-DH
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
102 ABB
Transformer input module, ring lug terminals 12I, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CC
Transformer input module, ring lug terminals 12I, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CD
Transformer input module, ring lug terminals 9I+3U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-BC
Transformer input module, ring lug terminals 9I+3U, 5A, 50/60 Hz Qty:
1 2 1MRK 002 247-BD
Transformer input module, ring lug terminals 5I, 1A+4I, 5A+3U,50/60 Hz
Qty:
1 2 1MRK 002 247-BF
Transformer input module, ring lug terminals 7I+5U, 1A, 50/60 Hz
Qty: 1 2 1MRK 002 247-AS
Transformer input module, ring lug terminals 7I+5U, 5A, 50/60 Hz Qty:
1 2 1MRK 002 247-AT
Transformer input module, ring lug terminals 6I, 5A+1I, 1A+5U,50/60 Hz
Qty:
1 2 1MRK 002 247-AX
Transformer input module, ring lug terminals 3I, 5A+4I, 1A+5U,50/60 Hz
Qty:
1 2 1MRK 002 247-AY
Transformer input module, ring lug terminals 3IM, 1A+4IP, 1A+5U,50/60 Hz
Qty: 1 2 1MRK 002 247-EC
Transformer input module, ring lug terminals 3IM, 5A+4IP, 5A+5U,50/60 Hz
Qty: 1 2 1MRK 002 247-ED
Transformer input module, ring lug terminals 6I+6U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AC
Transformer input module, ring lug terminals 6I+6U, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AD
Transformer input module, ring lug terminals 3I, 5A+3I, 1A+6U,50/60 Hz
Qty:
1 2 1MRK 002 247-AF
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 103
Transformer input module, ring lug terminals 6I, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-DC
Transformer input module, ring lug terminals 6I, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-DD
Note: One Analog digital conversion module, with time synchronization is always delivered with each Transformerinput module.
Case size
When ordering I/O modules, observe the maximum quantities according to tables below.
Note: Standard order of location for I/O modules is BIM-BOM-SOM-IOM-MIM from left to right as seen from therear side of the IED, but can also be freely placed.
Note: Maximum quantity of I/O modules depends on the type of connection terminals.
Maximum quantity of I/O modules
Case sizes BIM IOM BOM/SOM
MIM Maximum in case
1/1 x 19”, one (1) TRM 14 6 4 4 14 (max 4 BOM+SOM+MIM)
1MRK 000 151-NC
1/1 x 19”, two (2) TRM 11 6 4 4 11 (max 4 BOM+SOM+MIM)
1MRK 000 151-ND
3/4 x 19”, one (1) TRM 8 6 4 1 8 (max 4 BOM+SOM+1MIM)
1MRK 000 151-NB
3/4 x 19”, two (2) TRM 5 5 4 1 5 (max 4 BOM+SOM+1MIM)
1MRK 000 151-NE
1/2 x 19”, one (1) TRM 3 3 3 0 3 1MRK 000 151-NA
Maximum quantity of I/O modules, with ring lug terminals,module limits see above
Case sizes Maximum in case Possible locations for I/O moduleswith ringlugs
1/1 x 19”, one (1) TRM 7 P3, P5, P7, P9, P11, P13, P15 1MRK 000 151-NC
1/1 x 19”, two (2) TRM 5 P3, P5, P7, P9, P11 1MRK 000 151-ND
3/4 x 19”, one (1) TRM 4 P3, P5, P7, P9 1MRK 000 151-NB
3/4 x 19”, two (2) TRM 2 P3, P5 1MRK 000 151-NE
1/2 x 19”, one (1) TRM 1 P3 1MRK 000 151-NA
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
104 ABB
Binary input/output modules
Make BIM with 50 mA inrush current the primary choice. BIM with 50 mA inrush currentfulfill additional standards. As a consequence the EMC withstand capability is furtherincreased.BIM with 30 mA inrush current is still available.For pulse counting, for example kWh metering, the BIM with enhanced pulse countingcapabilities must be used.
Binary input module (BIM) 16 inputs
RL 24-30 VDC, 30 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-DB
RL 48-60 VDC, 30 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-AB
RL 110-125 VDC, 30 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-BB
RL 220-250 VDC, 30 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-CB
RL 24-30 VDC, 50 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-DD
RL 48-60 VDC, 50 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-AD
RL 110-125 VDC, 50 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-BD
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 105
RL 220-250 VDC, 50 mA Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-CD
Binary input module (BIM) with enhanced pulsecounting capabilities, 16 inputs
RL 24-30 VDC Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-HA
RL 48-60 VDC Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-EA
RL 110-125 VDC Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-FA
RL 220-250 VDC Qty: 1 2 3 4 5 6
8 9 10 11 12 13
7
14
1MRK 000 508-GA
Binary output module 24 output relays (BOM) Qty: 1 2 3 4 1MRK 000 614-AB
Static binary output module (SOM)
RL 48-60 VDC Qty: 1 2 3 4 1MRK 002 614-BA
RL 110-250 VDC Qty: 1 2 3 4 1MRK 002 614-CA
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
106 ABB
Make IOM with 50 mA inrush current the primary choice. IOM with 50 mA inrush currentfulfill additional standards. As a consequence the EMC withstand capability is furtherincreased.IOM with 30 mA inrush current is still available.
Binary input/output module (IOM) 8 inputs, 10 outputs, 2 high-speed outputs
RL 24-30 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-GB
RL 48-60 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-AC
RL 110-125 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-BC
RL 220-250 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-CC
RL 24-30 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-GD
RL 48-60 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-AE
RL 110-125 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-BE
RL 220-250 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-CE
Binary input/output module (IOM with MOV), 8 inputs, 10 outputs, 2 high-speed outputs
RL 24-30 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-GC
RL 48-60 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-AD
RL 110-125 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-BD
RL 220-250 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-CD
mA input module 6 channels (MIM) Qty: 1 2 3 4 1MRK 000 284-AB
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 107
Station communication ports
Note: Optical ethernet module, 2 glass interfaces is not allowed together with SLM.
Optical ethernet module, 1 channel glass 1MRK 002 266-AA
Optical ethernet module, 2 channel glass 1MRK 002 266-BA
Serial and LON communication module, supports SPA/IEC 60870-5-103, LON and DNP3.0
Serial/LON plastic interface 1MRK 001 608-AA
Serial plastic/LON glass interface 1MRK 001 608-BA
Serial/LON glass interface 1MRK 001 608-CA
Serial IEC 60870-5-103 plastic interface 1MRK 001 608-DA
Serial IEC 60870-5-103 plastic/glass interface 1MRK 001 608--EA
Serial IEC 60870-5-103 glass interface 1MRK 001 608-FA
Galvanic RS485 communication module for DNP 3.0 1MRK 002 309-AA
Remote end serial communication for C37.94
Rule: Max two LDCM can be ordered
Optical short range line data communication module(Multi mode 850 nm) (SR LDCM)
Qty:
1 2 1MRK 002 122-AB
Optical medium range line data communication module(Single mode 1310 nm) (MR LDCM)
Qty:
1 2 1MRK 002 311-AA
Time synchronization
Rule: Only one Time synchronization can be ordered.
GPS Time module (GTM) 1MRK 002 282-AB
IRIG-B Time synchronization module 1MRK 002 305-AA
Engineering facilities
19” rack mounting kit for 1/2 x 19” case or 2 x RHGS6 or RHGS12 Quantity: 1MRK 002 420-BB
19” rack mounting kit for 3/4 x 19” case or 3 x RHGS6 Quantity: 1MRK 002 420-BA
19” rack mounting kit for 1/1 x 19” case Quantity: 1MRK 002 420-CA
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
108 ABB
Note: Wall mounting not recommended with communication moduleswith fibre connection (SLM, OEM, LDCM)Wall mounting kit for terminal
Quantity: 1MRK 002 420-DA
Flush mounting kit for terminal Quantity: 1MRK 000 020-Y
Flush mounting kit + IP54 sealing (factory mounted). Cannot beordered separately thus must be specified when ordering a terminal.
Quantity: 1MRK 002 420-EA
Accessories
GPS antenna and mounting details
GPS antenna, including mounting kits Quantity: 1MRK 001 640-AA
Cable for antenna, 20 m Quantity: 1MRK 001 665-AA
Cable for antenna, 40 m Quantity: 1MRK 001 665-BA
Interface converter (for remote end data communication)
External interface converter from C37.94 to G703 Quantity: 1 2 1MRK 002 245-AA
External interface converter from C37.94 to G703.E1 Quantity: 1 2 1MRK 002 245-BA
Test switch
The test system COMBITEST intended for usewith the IED 670 products is described in1MRK 512 001-BEN and 1MRK 001024-CA.Please refer to the website: www.abb.com/substationautomation for detailed information.
Due to the high flexibility of our product andthe wide variety of applications possible thetest switches needs to be selected for eachspecific application.
Select your suitable test switch base on theavailable contacts arrangements shown in thereference documentation.
However our proposals for suitable variantsare;
Single breaker/Single or Three Phase tripwith internal neutral on current circuits(ordering number RK926 315-AK).
Single breaker/Single or Three Phase tripwith external neutral on current circuits(ordering number RK926 315-AC).
Multi-breaker/Single or Three Phase trip withinternal neutral on current circuits (orderingnumber RK926 315-BE).
Multi-breaker/Single or Three Phase trip withexternal neutral on current circuit (orderingnumber RK926 315-BV).
The normally open "In test mode" contact29-30 on the RTXP test switches should beconnected to the input of the test functionblock to allow activation of functionsindividually during testing.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 109
Test switches type RTXP 24 is orderedseparately. Please refer to Section "Relateddocuments" for reference to correspondingdocuments.
RHGS 6 Case or RHGS 12 Case with mountedRTXP 24 and the on/off switch for dc-supply
are ordered separately. Please refer to Section"Related documents" for reference tocorresponding documents.
Protection cover
Protective cover for rear side of RHGS6, 6U, 1/4 x 19” Quantity: 1MRK 002 420-AE
Protective cover for rear side of terminal, 6U, 1/2 x 19” Quantity: 1MRK 002 420-AC
Protective cover for rear side of terminal, 6U, 3/4 x 19” Quantity: 1MRK 002 420-AB
Protective cover for rear side of terminal, 6U, 1/1 x 19” Quantity: 1MRK 002 420-AA
External resistor unit
High impedance resistor unit 1-ph with resistor and voltagedependent resistor for 20-100V operating voltage
Quantity:
1 2 3 RK795101-MA
High impedance resistor unit 3-ph with resistor and voltagedependent resistor for 20-100V operating voltage
Quantity: RK795101-MB
High impedance resistor unit 1-ph with resistor and voltagedependent resistor for 100-400V operating voltage
Quantity:
1 2 3 RK795101-CB
High impedance resistor unit 3-ph with resistor and voltagedependent resistor for 100-400V operating voltage
Quantity: RK795101-DC
Combiflex
Key switch for settings
Key switch for lock-out of settings via LCD-HMI Quantity: 1MRK 000 611-A
Note: To connect the key switch, leads with 10 A Combiflex socket on one end must be used.
Side-by-side mounting kit Quantity: 1MRK 002 420-Z
Configuration and monitoring tools
Front connection cable between LCD-HMI and PC Quantity: 1MRK 001 665-CA
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
110 ABB
LED Label special paper A4, 1 pc Quantity: 1MRK 002 038-CA
LED Label special paper Letter, 1 pc Quantity: 1MRK 002 038-DA
Manuals
Note: One (1) IED Connect CD containing user documentation (Operator’s manual, Technical referencemanual, Installation and commissioning manual, Application manual and Getting started guide),Connectivity packages and LED label template is always included for each IED.
Rule: Specify additional quantity of IED Connect CD requested. Quantity: 1MRK 002 290-AB
User documentation
Rule: Specify the number of printed manuals requestedOperator’s manual
IEC Quantity: 1MRK 511 228-UEN
ANSI Quantity: 1MRK 511 228-UUS
Technical reference manual IEC Quantity: 1MRK 511 227-UEN
ANSI Quantity: 1MRK 511 227-UUS
Installation and commissioning manual IEC Quantity: 1MRK 511 229-UEN
ANSI Quantity: 1MRK 511 229-UUS
Application manual IEC Quantity: 1MRK 511 230-UEN
ANSI Quantity: 1MRK 511 230-UUS
Engineering guide IED 670 products Quantity: 1MRK 511 179-UEN
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
ABB 111
Reference information
For our reference and statistics we would be pleased to be provided with the following application data:
Country: End user:
Station name: Voltage level: kV
Related documents
Documents related to REC670 Identity number
Operator’s manual 1MRK 511 228-UEN
Installation and commissioning manual 1MRK 511 229-UEN
Technical reference manual 1MRK 511 227-UEN
Application manual 1MRK 511 230-UEN
Product guide customized 1MRK 511 231-BEN
Product guide pre-configured 1MRK 511 232-BEN
Product guide IEC 61850-9-2 1MRK 511 219-BEN
Sample specification SA2005-001280
Connection and Installation components 1MRK 513 003-BEN
Test system, COMBITEST 1MRK 512 001-BEN
Accessories for 670 series IEDs 1MRK 514 012-BEN
670 series SPA and signal list 1MRK 500 092-WEN
IEC 61850 Data objects list for 670 series 1MRK 500 091-WEN
Engineering manual 670 series 1MRK 511 240-UEN
Communication set-up for Relion 670 series 1MRK 505 260-UEN
More information can be found on www.abb.com/substationautomation.
Bay control REC670 1MRK 511 231-BEN BCustomizedProduct version: 1.2 Issued: September 2011
112 ABB
113
Contact us
ABB ABSubstation Automation ProductsSE-721 59 Västerås, SwedenPhone +46 (0) 21 32 50 00Fax +46 (0) 21 14 69 18
www.abb.com/substationautomation
1MR
K 5
11 2
31-B
EN
B©
Cop
yrig
ht 2
011
AB
B. A
ll rig
hts
rese
rved
.