http://www.dingli.com
Powering Network Experience
PILOT WALKTOUR OPERATION GUIDE
V3.8 (IPHONE)
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Test Procedure
• Call Test—Outdoor Test
• FTP Download—Indoor Test
• Parallel Test
Service Test (Examples)
Other Features
FAQ
Contents
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Pilot Walktour is a commercial phone-based air interface measurement software.
Overview
Technology Service Test Data Processing
GSM/CDMA/TDSCDMA/
WCDMA/LTE
Call/MOS/FTP/HTTP/Ping/E
mail/CSFB
Supported terminals:
iPhone5s/iPhone6/iPhone6
Plus Pilot Fleet Unify
Pilot Pioneer
Expert
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Interaction with
Pilot Fleet UnifyMap InformationTest Information
Start Pilot Walktour
In-built Management
Create a test plan
Select a test scenario
Start test
Display information
Data management Data statistics
Event/Message (including L3
decoding)/TCP/IP/Parameters/Data/Graph
Settings
Post Processing
Test Process
Data replay
Test Procedure
End test
Select a test service
CSFB analysis
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Tap the Walktour icon
to start Pilot Walktour.
Main Interface
The main interface consists of Auto Test, Manual, MultiTest. Users may tap About to view the software version or tap Exit to exit Pilot
Walktour.
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Tap Manual on the main interface.
Manual Test
1. Task: to create or change a service test plan
2. Start: to start a service test after settings
3. Info: to view test information during service tests
4. Data: to view or manage recorded test data
5. Statistics: to generate statistics and reports on test
data
6. Settings: to configure the settings for service tests
7. Time: to synchronize time on two or multiple
devices
8. Playback: to replay recorded test data files
9. CSFB Analysis: to view detailed CSFB analysis
information and generate associated reports
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Auto analysis: Users may enable Auto Analysis and Tip/Auto GoOrNogo and Tip as required. This way, the software will conduct corresponding
auto analysis after the service test is completed.
2. Chart settings: Users may set parameters and colors to be displayed on the chart.
3. Airplane mode: Users may set whether to enable the Airplane mode. If this function is enabled, the airplane mode on the phone will be automatically
enabled and disabled every time before a test.
4. Alarm Settings: Users may set the alarm types, customize events, set conditions for event trigger, and customize alarm modes (e.g. audio alarm,
show event icons on map or chart window) as required.
Chart Settings Alarm Settings
Settings—Chart/Alarm/Auto Analysis
Auto Analysis Airplane Mode
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Settings > Data Upload Settings.
2. Set data upload network.
3. Set server information.
• Fleet: Users need to select the corresponding protocol, and register the device on Pilot
Fleet Unify server.
• FTP: The username and password must be available.
Settings—Data Upload
Handset
Pilot Fleet UnifyDeliver tasks and
download maps
Upload data
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Handset
Pilot Fleet UnifyDeliver tasks and
download maps
Upload data
1. Log in to Pilot Fleet Unify via the IE browser on a PC and register the device on Pilot Fleet Unify.
2. On Pilot Fleet Unify, choose Device Management > Add > Walktour.
3. In the window that is displayed, set required information, such as Group, Subgroup, Device ID, Device Name, Phone
Model, and IMEI.
4. Set correct information for Network Type and Device Model, and then click Save.
Settings—Register Devices on Pilot Fleet Unify
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Info > Map > Settings.
2. Tap Default Map to enter the Map Settings window.
3. Select Indoor Maps, Offline Maps or Online Maps as required.
Settings—Select Maps
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Copy and paste the offline map package into the path: var/mobile/Documents/ walktour/map/offline.
2. Tap Settings > Default Map, and select Offline Map.
3. Tap the Load button on the Map window to load the offline map package, corresponding base station and drive
routes.
Settings—Load Offline Maps/Base Station
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Settings > Info, tap Load, and select Indoor Maps.
2. Tap the icon on the Province_City window, enter province and city name, and then tap Save.
3. Add building, floor, and map information, and then import an indoor map (photos or iBWave) saved on the
phone. Supported indoor map formats are:
• Photo: *.jpg, *.png, *.bmp
• iBWave: .*tab
Settings—Indoor Test
Add Province and city Add buildings Add floors Add maps
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Manual > Info > Parameter > Settings to select a network technology and parameters to display. Users
may:
• Tap Add to add a parameter to display
• Tap the icon beside a parameter to delete the parameter.
• Tap Reset to restore the default settings.
Settings—Custom Parameters
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Customize Workspaces
Tap Settings > Customize
Workspaces to set the workspaces
that need to be displayed.
Time Synchronization
Tap Manual > Time to enter the Time
Synchronization window to synchronize the
system time between the MO and MT handsets.
Users need to enable the MO-MT function on the
handsets.
Data Storage Format
Tap Settings > Data Storage Format
to set data storage format, TCP/IP
sniffer modes, and data partition
modes.
Other Settings
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Create and select a test task Select a test scenario Start test
1. Tap Manual > Task, tap New, and select a service test template as required
2. Configure the service test template, and return to Task list to select the configured task.
3. Tap Start, select a test scenario (Outdoor, Indoor), tap OK to start the service test.
Start Test
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
View Test Information
Tap Manual > Info to view various information by tapping the buttons at the bottom of window, including Map, Event,
Data, Statistics, Parameter, Video, and Chart.
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Slide screen Tap a message or
TCP/IP recordSwitch windows
View Test Information
Tap Manual > Info > Event, slide screen to the right for the Message window display, in order to view decoded
messages or TCP/IP information. Users may select an event to view detailed information.
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Freeze Screen and Add Label to Events
Tap Manual > Info > Event.
• Tap Freeze so that events and messages will pause on the current time stamp. Newly incoming events and
messages will not be displayed on screen, but will be saved in the background.
• Tap Settings to enter the Setting Event window, where users may set messages or events to be displayed.
• Tap Label to add labels to events as required.
Freeze Screen Settings Label
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. To pause the test, click the Pause button in the Manual main menu.
2. Once all test tasks have been completed, Pilot Walktour will automatically stop the test.
3. Once the test has ended, users may:
• Generate statistics for the service test
• Upload test data to Pilot Fleet Unify server or download test data to the PC.
• Process test data on Pilot Pioneer Expert or Pilot Fleet Unify.
End Test and Data Post-processing
Pause test Statistics
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Test Procedure
• Call Test—Outdoor Test
• FTP Download—Indoor Test
• Parallel Test
Service Test (Examples)
Other Features
FAQ
Contents
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Enable Bluetooth on both handsets or make sure both handset access to the same LAN.
2. On both handsets, tap Manual > Time to enter the Time Synchronization window.
3. On either handset, tap Broadcast Device Information, and set the time on the device as the reference time.
4. Tap the other handset's name in the search result, and then tap Accept on the handset on which Broadcast Device Information is
enabled to accept the connection request.
5. Once connection is successful, tap Request Server Time on either handset to synchronize time.
Call Test (Outdoor Test)—Time Synchronization
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Manual > Task > New to create a new task (take MOC/MTC as an example)
2. Set information for MOC and MTC based on the actual situation.
3. Tap the back icon and tap Save.
For MO-MT test, time synchronization is required.
Call Test (Outdoor Test)—New Task
Create a taskSave the task
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. In the Task window, select MOC or MTC, and return to the main menu.
2. Tap Info > Map > Settings > Default Map, and select Online Maps.
3. Tap Start on the main menu, select Outdoor, enable GPS, and enter information for Test Site, Tester,
Loops, etc.
4. Tap OK to start the test.
Call Test (Outdoor Test)—Select Test Scenario
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Turn to the Map window. If GPS function is normal, the online map will be automatically loaded and pinpoints will be marked on the map.
Use two fingers to press on the map window and slide to zoom in and out the map. Use one finger to press on the map and slide to move the map.
Tap Settings to set the parameters to be displayed on the Map window.
Tap Clear to delete base stations, map, or test routes.
The entire process of call test is recorded on the Event window; the message flow and L3 message decoding information is recorded on the Message window.
Call Test (Outdoor Test)—Tips
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Manual > Task.
2. Tap New, and select FTP Download to create a new FTP Download task template.
3. Enter required information such as the FTP server information for the template.
4. Tap the back icon on the left upper corner, and tap Save.
FTP Download (Indoor Test) —New Task
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. In the Task window, select the added task template FTP Download from the list, and tap the back icon to return to the
main menu.
2. Tap Info > Map > Settings > Default Map, select Indoor Maps.
3. Tap Start, select Indoor, enter required information (e.g. Test Site, Tester, Loops, etc.), and then tap Building and Floor
to load a building and floor map.
4. Tap OK to start the test.
FTP Download (Indoor Test) — Select Test Scenario
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
On the Map window, tap Pinpoint to pinpoint a predefined test route or start a test with pinpoints; the test route is saved automatically.
Use two fingers to press on the map and slide to zoom in and out the map; use one finger to press on the map and slide to move the map.
Tap Settings to set the parameters to be displayed on the Map window.
Tap Clear to delete map or test routes.
Tap Load to load an indoor map.
The FTP download process is recorded on the Event window; the real-time download rate is recorded on the Data window.
FTP Download (Indoor Test) -Tips
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Info > Map > Settings, and enable Point Adjustment.
2. The pinpoint adjustment tool will appear when conducting pinpointing on the Map window. The respective points
are adjusted by using the four keys (up, down, left, right) and confirmed by tapping the central key. See the
figures below:
FTP Download (Indoor Test) -Tips
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Task> New, and select Parallel Service to create a template.
2. Under Multi Service List, tap New or Import to add multiple test tasks.
• Import: add existing tasks from the task list into the Multi Service List.
• New: create new tasks and add them to the Multi Service List.
3. Once the tasks have been added, click the back icon and then tap Save.
Parallel Test (Indoor Test) —New Task
Parallel service test is used to test
multiple services simultaneously. Users
can select voice and data services into
Parallel Service templates.
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. In the Task window, select the added Parallel Service task template from the list, and tap the back icon to return to the
main menu.
2. Tap Info > Map > Settings > Default Map, and select Indoor Maps.
3. Tap Start, select Indoor, enter required information (e.g. Test Site, Tester, Loops, etc.), and then tap Building and
Floor to load a building and floor map.
4. Tap OK to start the test.
Select building and floor where the test
is conducted.
Parallel Test — Select Test Scenario
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
On the Map window, tap Pinpoint to pinpoint a predefined test route or start a test with pinpoints; the test route is saved
automatically.
Use two fingers to press on the map and slide to zoom in and out the map; use one finger to press on the map and slide to move the
map.
Tap Settings to set the parameters to be displayed on the Map
window.
Tap Clear to delete map or test routes.
Tap Load to load an indoor map.
Parallel Test—Tips
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Test Procedure
• Call Test—Outdoor Test
• FTP Download—Indoor Test
• Parallel Test
Service Test (Examples)
Other Features
FAQ
Contents
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Based on the instructions introduced previously, users can also configure more test templates, including Idle, Ping, HTTP Page,
HTTP Download, HTTP Upload, WAP Page, WAP Download, Email, SpeedTest, Video Play, Facebook, Multi FTP, Traceroute,
SMS, and PBM. The figure below shows the task template for HTTP Page, HTTP Download, and Video Play.
Configure Other Tasks (1)
Video Play service test support multiple service type,
including Youku, Youtube, ifeng, sohu, iqiyi, and
Facebook.
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Tap this button to move test tasks in the preferred order.
Tap these buttons to save and import projects.
Test Task Management
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Make sure the test device has been added into Pilot Fleet Unify, and that the test task has been configured.
2. In the main menu, tap Auto Test, select Fleet as the protocol type, and set the server IP and port.
3. Tap Manually Update on the right upper corner, so that Pilot Walktour can download the test task from Pilot Fleet Unify.
4. In Auto test mode, Pilot Walktour will automatically start testing once the test task has been downloaded.
Auto Test— Overview
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. In Manual, tap Statistics.
2. Select a data page, and tap Statistics at the left lower corner to enter the data management window. See Figure 1.
3. Select single or multiple data logs, tap Statistics at the bottom right corner to view statistics information. See Figure 2.
4. Tap a result record (e.g. Call Success Rate) to view detailed information. See Figure 3 and Figure 4.
Statistics—By File
Figure 1 Figure 2 Figure 3 Figure 4
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Statistics on the Manual main interface, tap the settings icon , and select Go or No-go.
2. Select a parameter, and enter a threshold for the selected parameter. If the statistics result is outside the defined
parameter threshold, the result will be highlighted.
Statistics— GO or NO-go Settings
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Statistics > Report.
2. Tap Export to export and view the statistics information of the current files. See Figure 2.
3. Tap a statistics template (e.g. FTP) on the Report Files window, select data files as required on the window that appears (see Figure 4),
and then tap Statistics at the bottom right corner of the window (see Figure 4) to view corresponding report information. See Figure 5.
Statistics—Export Reports
View InformationFigure 1 Figure 2Figure 3 Figure 4
Figure 5
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Settings > CSFB Analysis, and enable Auto Analysis and Tip.
2. After CSFB test, the CSFB analysis window will be automatically displayed.
• Tap the grey circle in the middle to display all CSFB results.
• Tap the failure percentage rectangle under the grey circle to display the summary of the events.
• Tap any event to expand the detailed call information, including failure reasons, related fallback frequency, originating network, etc.
3. Users may tap Select File on the upper right corner of CSFB Analysis window to select data files that requires CSFB analysis.
CSFB Analysis
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Playback to enter the Select File window. Select data files to be played, and tap OK. The playback control bar that can
be moved up or down as displayed.
2. Users may pause, play forward/backward, and step forward/backward as required.
3. Data file information can be synchronized to different windows (such Event, Message, Map, Parameter, and Meter Gauge
windows) during data file replay.
Data Replay
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Once the test is completed, the test data can be copied to a PC. Users may tap Manual > Data to delete or upload data
files.
• Delete data: Select a data log and tap the Delete button at the bottom.
• Upload: Select a data log and tap the Upload button at the bottom.
Data Management—Delete and Upload Data Files
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Users may tap Manual > Data to search or filter data as required.
• Filter: Tap Filter, and select Time, Task, Status, or Network to filter data files as required.
• Search: Tap Search, and enter exception keywords (e.g. Ping Failure) to search data files that include the defined exceptions.
• Filter Exceeded: Tap Filter Exceeded, define a condition, and tap OK to hide data files which test duration is less than the
defined value (e.g. 3 minutes).
• Display: Tap Display, and set File Display Mode and Display Option to display information as required.
Data Management—Search and Filter Data Files
42
Filter Search Filter Exceeded Display
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
On the Data Management window, users may:
• Tap a data file in the Data Management window, and select Properties to view the data properties (e.g. upload status, test duration) or
test plans as required
• Tap Display, and select Display Exception Count. Tap a data file, and select Exceptions to view corresponding information.
• Tap Display, and select Display Go or No-Go. Tap a data file, and select Go or Nogo to view corresponding information.
Data Management—View Data Information
43
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
1. Tap Settings > Data Storage Format to set TCP/IP sniffer modes under TCP/IP COLLECTION MODE.
• All: to sniff the entire data.
• Header Only: to sniff only the frame header and the last ten bytes of each data packet for all services.
• Optimized: to sniff the entire protocol part and the first data packet for FTP and PBM service tests.
2. Users may tap Settings > TCP/IP Filter Settings to select which protocol packets will be sniffed. User may maintain the default settings.
3. After settings, enable TCP/IP on the Start Test window.
TCP/IP Sniffer
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Test Procedure
• Call Test—Outdoor Test
• FTP Download—Indoor Test
• Parallel Test
Service Test (Examples)
Other Features
FAQ
Contents
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Data files can be exported from the test device to a PC by using the tools below:
iTool
Sync Assistant
iSpirit
iFunBox
iPhoneBrowser
……
Back up Test Data
Powering Network Experience© Dingli (09/18/2015) DL 738 PG
Import a Map into the iPhone Photo Album
1. Connect the iPhone to a PC via cables.
2. Open iTunes on a PC.
3. Select the test iPhone in the DEVICES column.
4. Select Photos.
5. Select Sync Photos from…
6. Select the location folder for maps in the iPhone.
7. Tap Apply.
8. Wait until the synchronization completes, and maps will be available in the iPhone
Photo Album.
Import Map
世纪通信 鼎利支持Powering Network Experience
No. 8, 5th Technology Road, Gangwan
Avenue, Zhuhai,
P.R. China 519085
0756-3626100 Fax : 0756-3391900Tel :
Email :