11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. C1/C2 Buttons (Customizable)
18. USB Port
19. Micro-USB Port
1. Power Button
2. Return to Home (RTH) Button
3. Control Sticks
4. Status LED
5. Battery Level LEDs
6. Power Port
7. Mobile Device Holder
8. Small Device Positioning Tabs
(such as mobile phone)
9. Antennas
10. Handle Bar
Phantom 3 Professional Remote Controller
● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.
3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.
4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,
radio transmission towers, or Wi-Fi hotspots.
5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when
flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.
6. The Phantom 3 Professional cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning
system will be operational.
● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which
can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal
performance.
1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and
steel reinforcements underground.
2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
3. DO NOT calibrate beside massive metal objects.
4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after
placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.
Fly Safe Appendix
● P Mode:In this mode, the Phantom 3 Professional can use GPS and the Vision
Positioning system, allowing it to hover accurately in position indoors
and out. When GPS is available, a Home Point will be locked so that the
Phantom 3 Professional can Return to Home if the Remote Controller
signal is lost.
※ This Quick Start Guide is subject to change without prior notice.
Folded
There are three states in P mode:
P-GPS: GPS works best when outdoors and in a wide open area. Your
Phantom 3 Professional uses GPS to hover in place when there is a
strong GPS signal.
P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning
system to hover accurately.
P-ATTI: Neither GPS nor the Vision Positioning system are available.
The aircraft will only use its barometer for altitude and other on-board
sensors for attitude stabilization.
Note that the Vision Positioning system may not work properly when
the Phantom 3 Professional is flying over water, over surfaces without
a clear pattern, or in a low-light environment.
● Return to Home:When there is a strong GPS signal, the aircraft will be able to
record a Home Point and return to that Home Point when
required. The Home Point location is recorded when the GPS
signal icon in the DJI Pilot app is either yellow or green.
The aircraft will return to the Home Point automatically in the
following scenarios (all require a strong GPS signal):
Smart RTH: When the RTH button on the Remote Controller
or in the DJI Pilot app is pressed.
Low-Battery RTH: A notification will appear in the DJI Pilot
app requesting the pilot to take action when the battery level
falls under a certain level.
Failsafe RTH: When the Remote Controller’s signal is lost.
GPS Positioning
●
Remote Controller
Operating Frequency 2.400 GHz-2.483 GHz
Max. Transmission Distance 2 km (outdoors and unobstructed)
Video Output Port USB
Operating Temperature Range 0°C to 40°C
Battery 6000 mAh LiPo 2S
Mobile Device Holder Tablets and smartphones
Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm
Working Voltage 1.2 A @7.4 V
●
Charger
Voltage 17.4 V
Rated Power 100 W
●
Intelligent Flight Battery(PH3-4480 mAh-15.2 V )
Capacity 4480 mAh
Voltage 15.2 V
Battery Type LiPo 4S
Energy 68 Wh
Net Weight 365 g
Operating Temperature -10℃ to 40℃
Max. Charging Power 100 W
FCC ID:SS3-WM3231503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including
interference that may cause undesired operation.
● Aircraft
Weight (Including Battery) 1280 g
Max. Ascent Speed 5 m/s
Max. Descent Speed 3 m/s
Max. Speed 16 m/s (ATTI mode, no wind)
Max. Flight Altitude 6000 m
Max. Flight Time Approximately 23 minutes
Operating Temperature Range 0°C to 40°C
GPS GPS/GLONASS
●
Gimbal
Angular Vibration Range Pitch: − 90° to +30°
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 30 cm-300 cm
Operating Range 30 cm-300 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
●
Camera
Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s - 1/8000 s
Image Max. Size 4000 x 3000
Still Photography Modes Single shot
Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias
Time-lapse
Video Recording Modes UHD : 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60
HD: 1280x720p 24/25/30/48/50/60
Max. Bitrate of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range 0°C to 40°C
It’s time to meet your Phantom 3 Professional.
The Phantom 3 Professional’s camera records video at up to 4K and captures 12 megapixel photos.
Review the diagram below for a full list of your Phantom 3 Professional’s parts:
This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Professional at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.
Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.
* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending
on conditions in your immediate surroundings.
Mobile device connection
DJI encourages you to enjoy flying your Phantom 3 Professional in a safe, responsible, and smart way. To do this, it is important to
understand some basic flight guidelines, both for your protection and for the safety of those around you.
1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above
or near people or animals.
2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to
Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.
3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.
4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)
above ground level, or in line with your local laws and regulations.
Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as
No-Fly Zones.
To enable P Mode, toggle the Flight Mode Switch
to the P position.
10
9
87
3
4
5
1
2
6
14
12
1615
11
17
19 18
13
17
2
7
4
5
9
8
6
3
1
Guida RapidaV1.0
1. Gimbal and Camera
2. Vision Positioning System
3. Camera Micro-SD Card Slot
4. Aircraft Micro-USB Port
5. Front LEDs
6. Motors
7. Propellers
8. Aircraft Status Indicators
9. Antennas
10. Intelligent Flight Battery
11. Power Button
12. Battery Level Indicators
13. Link Button
14. Camera Micro-USB Port
PHANTOM 3PROFESSIONAL
1211
14
10
13
1
8
2
m
m
1
7
2
m
m
105 mm
71 mm
● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote
Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby
buildings to avoid crashing.
Return to home
28
9.5
m
m
28
9 m
m
18
5 m
m
9 feet 10 inches
1 foot
Vision Positioning
Altitude
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. C1/C2 Buttons (Customizable)
18. USB Port
19. Micro-USB Port
1. Power Button
2. Return to Home (RTH) Button
3. Control Sticks
4. Status LED
5. Battery Level LEDs
6. Power Port
7. Mobile Device Holder
8. Small Device Positioning Tabs
(such as mobile phone)
9. Antennas
10. Handle Bar
Remote Controller
● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.
3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.
4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,
radio transmission towers, or Wi-Fi hotspots.
5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when
flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.
6. The Phantom 3 Professional cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning
system will be operational.
● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which
can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal
performance.
1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and
steel reinforcements underground.
2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
3. DO NOT calibrate beside massive metal objects.
4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after
placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.
Fly Safe Appendix
● P Mode:In this mode, the Phantom 3 Professional can use GPS and the Vision
Positioning system, allowing it to hover accurately in position indoors
and out. When GPS is available, a Home Point will be locked so that the
Phantom 3 Professional can Return to Home if the Remote Controller
signal is lost.
※ This Quick Start Guide is subject to change without prior notice.
Folded
There are three states in P mode:
P-GPS: GPS works best when outdoors and in a wide open area. Your
Phantom 3 Professional uses GPS to hover in place when there is a
strong GPS signal.
P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning
system to hover accurately.
P-ATTI: Neither GPS nor the Vision Positioning system are available.
The aircraft will only use its barometer for altitude and other on-board
sensors for attitude stabilization.
Note that the Vision Positioning system may not work properly when
the Phantom 3 Professional is flying over water, over surfaces without
a clear pattern, or in a low-light environment.
● Return to Home:When there is a strong GPS signal, the aircraft will be able to
record a Home Point and return to that Home Point when
required. The Home Point location is recorded when the GPS
signal icon in the DJI Pilot app is either yellow or green.
The aircraft will return to the Home Point automatically in the
following scenarios (all require a strong GPS signal):
Smart RTH: When the RTH button on the Remote Controller
or in the DJI Pilot app is pressed.
Low-Battery RTH: A notification will appear in the DJI Pilot
app requesting the pilot to take action when the battery level
falls under a certain level.
Failsafe RTH: When the Remote Controller’s signal is lost.
GPS Positioning
●
Remote Controller
Operating Frequency 2.400 GHz-2.483 GHz
Max. Transmission Distance 2 km (outdoors and unobstructed)
Video Output Port USB
Operating Temperature Range 0°C to 40°C
Battery 6000 mAh LiPo 2S
Mobile Device Holder Tablets and smartphones
Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm
Working Voltage 1.2 A @7.4 V
●
Charger
Voltage 17.4 V
Rated Power 100 W
●
Intelligent Flight Battery(PH3-4480 mAh-15.2 V )
Capacity 4480 mAh
Voltage 15.2 V
Battery Type LiPo 4S
Energy 68 Wh
Net Weight 365 g
Operating Temperature -10℃ to 40℃
Max. Charging Power 100 W
FCC ID:SS3-WM3231503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including
interference that may cause undesired operation.
● Aircraft
Weight (Including Battery) 1280 g
Max. Ascent Speed 5 m/s
Max. Descent Speed 3 m/s
Max. Speed 16 m/s (ATTI mode, no wind)
Max. Flight Altitude 6000 m
Max. Flight Time Approximately 23 minutes
Operating Temperature Range 0°C to 40°C
GPS GPS/GLONASS
●
Gimbal
Angular Vibration Range Pitch: − 90° to +30°
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 30 cm-300 cm
Operating Range 30 cm-300 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
●
Camera
Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s - 1/8000 s
Image Max. Size 4000 x 3000
Still Photography Modes Single shot
Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias
Time-lapse
Video Recording Modes UHD : 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60
HD: 1280x720p 24/25/30/48/50/60
Max. Bitrate of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range 0°C to 40°C
This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Professional at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.
Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.
* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending
on conditions in your immediate surroundings.
Mobile device connection
DJI encourages you to enjoy flying your Phantom 3 Professional in a safe, responsible, and smart way. To do this, it is important to
understand some basic flight guidelines, both for your protection and for the safety of those around you.
1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above
or near people or animals.
2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to
Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.
3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.
4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)
above ground level, or in line with your local laws and regulations.
Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as
No-Fly Zones.
To enable P Mode, toggle the Flight Mode Switch
to the P position.
10
9
87
3
4
5
1
2
6
14
12
1615
11
17
19 18
13
17
2
7
4
5
9
8
6
3
1
Quick Start GuideV1.0
3PROFESSIONAL
1211
14
10
13
1
8
2
m
m
1
7
2
m
m
105 mm
71 mm
● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote
Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby
buildings to avoid crashing.
Return to home
28
9.5
m
m
28
9 m
m
18
5 m
m
9 feet 10 inches
1 foot
Vision Positioning
Altitude
Phantom 3 Professional
E' il momento di incontrare e conoscere il vostro Phantom 3 Advanced.
La videocamera del Phantom 3 Advanced può restrira video a 1080p/60fps e catturare foto fino a 12 mp.
Vedere lo schema seguente per una lista completa delle parti del vostro Phantom 3 Advanced.
1. Gimbal e videocamera 2. Sistema di posizionamento Vision 3. Scomparto per scheda micro-SD della fotocamera 4. Porta micro-USB velivolo 5. LEDs anteriori 6. Motori 7. Eliche 8. Indicatori di stato del velivolo 9. Antenna10. Batteria intelligente di volo11. Pulsante Power (Accensione/Spegnimento)12. Indicatori livello batteria13. Pulsante collegamento14. Porta micro-USB videocamera
Phantom 3 Advanced Telecomando
● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.
3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.
4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,
radio transmission towers, or Wi-Fi hotspots.
5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when
flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.
6. The Phantom 3 Advanced cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning
system will be operational.
● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which
can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal
performance.
1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and
steel reinforcements underground.
2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
3. DO NOT calibrate beside massive metal objects.
4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after
placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.
Fly Safe Appendix
● P Mode:In this mode, the Phantom 3 Advanced can use GPS and the Vision
Positioning system, allowing it to hover accurately in position indoors
and out. When GPS is available, a Home Point will be locked so that the
Phantom 3 Advanced can Return to Home if the Remote Controller signal
is lost.
※ This Quick Start Guide is subject to change without prior notice.
There are three states in P mode:
P-GPS: GPS works best when outdoors and in a wide open area.
Your Phantom 3 Advanced uses GPS to hover in place when there is
a strong GPS signal.
P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning
system to hover accurately.
P-ATTI: Neither GPS nor the Vision Positioning system are available.
The aircraft will only use its barometer for altitude and other on-board
sensors for attitude stabilization.
Note that the Vision Positioning system may not work properly when
the Phantom 3 Advanced is flying over water, over surfaces without a
clear pattern, or in a low-light environment.
● Return to Home:
When there is a strong GPS signal, the aircraft will be able to
record a Home Point and return to that Home Point when
required. The Home Point location is recorded when the GPS
signal icon in the DJI Pilot app is either yellow or green.
The aircraft will return to the Home Point automatically in the
following scenarios (all require a strong GPS signal):
Smart RTH: When the RTH button on the Remote Controller
or in the DJI Pilot app is pressed.
Low-Battery RTH: A notification will appear in the DJI Pilot
app requesting the pilot to take action when the battery level
falls under a certain level.
Failsafe RTH: When the Remote Controller’s signal is lost.
● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote
Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby
buildings to avoid crashing.
●
Remote Controller
Operating Frequency 2.400 GHz-2.483 GHz
Max. Transmission Distance 2 km (outdoors and unobstructed)
Video Output Port USB
Operating Temperature Range 0°C to 40°C
Battery 6000 mAh LiPo 2S
Mobile Device Holder Tablets and smartphones
Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm
Working Voltage 1.2 A @7.4 V
●
Charger
Voltage 17.4 V
Rated Power 57 W
●
Intelligent Flight Battery(PH3-4480 mAh-15.2 V )
Capacity 4480 mAh
Voltage 15.2 V
Battery Type LiPo 4S
Energy 68 Wh
Net Weight 365 g
Operating Temperature -10℃ to 40℃
Max. Charging Power 100 W
● Aircraft
Weight (Including Battery) 1280 g
Max. Ascent Speed 5 m/s
Max. Descent Speed 3 m/s
Max. Speed 16 m/s (ATTI mode, no wind)
Max. Flight Altitude 6000 m
Max. Flight Time Approximately 23 minutes
Operating Temperature Range 0°C to 40°C
GPS GPS/GLONASS
●
Gimbal
Angular Vibration Range Pitch: − 90° to +30°
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 30 cm-300 cm
Operating Range 30 cm-300 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
●
Camera
Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s - 1/8000 s
Image Max. Size 4000 x 3000
Still Photography Modes Single shot
Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias
Time-lapse
Video Recording Modes FHD: 1920x1080p 24/25/30/48/50/60
HD: 1280x720p 24/25/30/48/50/60
Max. Bitrate of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range 0°C to 40°C
*
DJI encourages you to enjoy flying your Phantom 3 Advanced in a safe, responsible, and smart way. To do this, it is important to
understand some basic flight guidelines, both for your protection and for the safety of those around you.
1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above
or near people or animals.
2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to
Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.
3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.
4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)
above ground level, or in line with your local laws and regulations.
Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as
No-Fly Zones.
To enable P Mode, toggle the Flight Mode Switch
to the P position.
It’s time to meet your Phantom.
The Phantom 3 Advanced’s camera records video at up to 1080p/60fps and captures 12 megapixel photos.
Review the diagram below for a full list of your Phantom 3 Advanced’s parts:
FCC ID:SS3-WM3221503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including
interference that may cause undesired operation.
PHANTOM 3
Quick Start GuideV1.0
ADVANCED
Return to home
1. Gimbal and Camera
2. Vision Positioning System
3. Camera Micro-SD Card Slot
4. Aircraft Micro-USB Port
5. Front LEDs
6. Motors
7. Propellers
8. Aircraft Status Indicators
9. Antennas
10. Intelligent Flight Battery
11. Power Button
12. Battery Level Indicators
13. Link Button
14. Camera Micro-USB Port
1211
14
10
13
1
8
2
m
m
1
7
2
m
m
105 mm
71 mm
2
7
4
5
9
8
6
3
1
GPS Positioning
28
9.5
m
m
28
9 m
m
18
5 m
m
9 feet 10 inches
1 foot
Vision Positioning
Altitude
11. Regolatore Gimbal
12. Regolatore settaggi videocamera
13. Pulsante registrazione video
14. Selettore modalità di volo
15. Pulsante di scatto
16. Pulsante riproduzione
17. Pulsanti C1/C2 (personalizzabili)
18. Porta USB
19. Porta Micro-USB
1. Pulsante accensione
2. Pulsante di ritorno alla base (RTH)
3. Leve di controllo
4. LED di stato
5. LED indicatore livello batteria
6. Porta alimentazione
7. Supporto dispositivio mobile
8. Linguetta posizionamento dispositivo
9. Antenne
10. Barra di tenuta
Piegato
Connessione dispositivo mobile
10
9
87
3
4
5
1
2
6
14
12
1615
11
17
19 18
13
17
Questo potente telecomando permette di pilotare e manovrare il tuo Phantom 3 Professional a distanze di
oltre 6.000 piedi (2 km) *, tenendo contemporaneamente i controlli della vostra fotocamera a portata di
mano.
Al suo interno vi è una batteria ricaricabile LiPo (polimeri di litio) e il DJI Lightbridge, che se abbinato con un
dispositivo mobile (telefono cellulare o tablet) compatibile vi dà una visione HD in diretta dalla fotocamera del
Phantom.
Questa distanza massima di trasmissione è stata testata in ambiente di laboratorio, ed è solo un riferimento. La distanza operativa massima può variare a seconda delle condizioni nelle vostre immediate vicinanze.
Phantom 3 Advanced Remote Controller
● Considerazioni ambientali:
● Calibrazione bussola:
Sicurezza voloAppendix
● P Mode:
※ This Quick Start Guide is subject to change without prior notice.
● Ritorno a casa (RTH):
●
Remote Controller
Operating Frequency 2.400 GHz-2.483 GHz
Max. Transmission Distance 2 km (outdoors and unobstructed)
Video Output Port USB
Operating Temperature Range 0°C to 40°C
Battery 6000 mAh LiPo 2S
Mobile Device Holder Tablets and smartphones
Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm
Working Voltage 1.2 A @7.4 V
●
Charger
Voltage 17.4 V
Rated Power 57 W
●
Intelligent Flight Battery(PH3-4480 mAh-15.2 V )
Capacity 4480 mAh
Voltage 15.2 V
Battery Type LiPo 4S
Energy 68 Wh
Net Weight 365 g
Operating Temperature -10℃ to 40℃
Max. Charging Power 100 W
● Aircraft
Weight (Including Battery) 1280 g
Max. Ascent Speed 5 m/s
Max. Descent Speed 3 m/s
Max. Speed 16 m/s (ATTI mode, no wind)
Max. Flight Altitude 6000 m
Max. Flight Time Approximately 23 minutes
Operating Temperature Range 0°C to 40°C
GPS GPS/GLONASS
●
Gimbal
Angular Vibration Range Pitch: − 90° to +30°
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 30 cm-300 cm
Operating Range 30 cm-300 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
●
Camera
Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s - 1/8000 s
Image Max. Size 4000 x 3000
Still Photography Modes Single shot
Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias
Time-lapse
Video Recording Modes FHD: 1920x1080p 24/25/30/48/50/60
HD: 1280x720p 24/25/30/48/50/60
Max. Bitrate of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range 0°C to 40°C
This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Advanced at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.
Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.
* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending
on conditions in your immediate surroundings.
It’s time to meet your Phantom.
The Phantom 3 Advanced’s camera records video at up to 1080p/60fps and captures 12 megapixel photos.
Review the diagram below for a full list of your Phantom 3 Advanced’s parts:
FCC ID:SS3-WM3221503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including
interference that may cause undesired operation.
PHANTOM 3
Quick Start GuideV1.0
ADVANCED
Return to home
1. Gimbal and Camera
2. Vision Positioning System
3. Camera Micro-SD Card Slot
4. Aircraft Micro-USB Port
5. Front LEDs
6. Motors
7. Propellers
8. Aircraft Status Indicators
9. Antennas
10. Intelligent Flight Battery
11. Power Button
12. Battery Level Indicators
13. Link Button
14. Camera Micro-USB Port
1211
14
10
13
1
8
2
m
m
1
7
2
m
m
105 mm
71 mm
2
7
4
5
9
8
6
3
1
GPS Positioning
28
9.5
m
m
28
9 m
m
18
5 m
m
9 feet 10 inches
1 foot
Vision Positioning
Altitude
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. C1/C2 Buttons (Customizable)
18. USB Port
19. Micro-USB Port
1. Power Button
2. Return to Home (RTH) Button
3. Control Sticks
4. Status LED
5. Battery Level LEDs
6. Power Port
7. Mobile Device Holder
8. Small Device Positioning Tabs
(such as mobile phone)
9. Antennas
10. Handle Bar
Folded
Mobile device connection
10
9
87
3
4
5
1
2
6
14
12
1615
11
17
19 18
13
17
DJI incoraggia a divertirsi col p roprio Phantom 3 advanced in modo sicuro, responsabile e intelligente. A tal fine è importante capire alcune linee gu ida del volo di base, sia per la vostra protezione che per la sicurezza di chi vi circonda.1. Vola in spazi aperti: Volare sempre in luoghi che sono liberi da edifici, alberi, linee elettriche, e altri ostacoli. Non volare sopra o vicino a persone o animali.
2. Mantenere sempre il controllo: anche quando si uti lizzano le funzioni di autopilota come Auto-Decollo, Auto-atterraggio, e
Auto - Ritorno a casa, tenere sempre le mani sul telecomando e mantenere il controllo del vostro aereo quando è in volo .
3. Mantenere il controllo a vista: mantenete il contatto visivo del vostro velivolo in ogni momento ed evit are di volare dietro gli
edifici o altr i ostacoli che potrebbero ostacolare la vostra visuale.
4. Monitorare la quota: per la sicurezza degli aeromobili di dimensioni standard e del traffico aereo, volare sempre ad altitudini
inferiori a 400 piedi (120 metri sopra il live llo del suolo, o in linea con leggi e normative locali.
Assicurarsi di calibrare la bussola in ogni nuovo luogo in cui si vola. La bussola è molto sensibile
alle interfer fenze elettromagne tiche che potrebbero causare anomalie e scarse prestazioni di
volo o addir ittura il fallimento della missione.
Per ottenere risultati ottimali è necessar ia la calibrazione. Calibrare la bussola quando:
a) L'indicatore di stato del velivolo lampeggia in rosso/g iallo.
b) Quando si vola in una nuova località.
● Non calibrare la bussola, dove c'è possibilità di for ti interferenze magnetiche (magnetite o parcheggi con strutture e rinforzi in
acciaio interrati).
● Non trasportare materiali ferromagnetici con voi durante la calibrazione, come chiavi o telefoni cellulari.
● Non calibrare accanto oggetti metallici voluminosi.
● Se il LED di stato del volo è rosso, prova re a calibrare di nuovo. Se lampeggia rosso/giallo alternativamente dopo
aver piazzato il velivolo a terra, la bussola ha rilevato inter ferenze magnetiche. Cambiare posizione.
1. Non volare in condizioni meteorologiche avverse. Questo include vento forte, neve, pioggia e smog.
2. Volare solo in aree aperte. Edifici alti e strutture in acciaio possono influenzare il segnale della bussola e del GPS.
3. Evitare ostacoli, folle di persone, linee elettriche ad alta tensione, alberi o corpi idrici.
4. Ridurre al minimo interferenze elettromagnetiche e non volare in zone con alti livelli di elettromagnetismo, comprese stazioni
mobili di telefonia o torri di trasmissione radio.
5. Le prestazioni della batteria sono soggette a fattori ambientali (densità e temperatura dell'aria). Fare molta attenzione quando
si vola oltre i 4500 mt slm, in quanto batteria e prestazioni del velivolo putrebbero essere ridotte.
6. A latitudini polari il Phantom 3 advanced non può operare in modalità P e non può utilizzare il GPS. Si può solo volare in moda-
lità ATTI e utilizzare il sistema di posizionamento Vision.
In questa modalità il Phnatom 3 ha un segnale GPS forte e si puòutilizzare il sistema di posizionamento Vision che gli permette di librarsi con precisione sia all'interno che all'esterno.In questa modalità, all'esterno, tramite un Punto Base salvato, il velivolo può tornare indietro in caso di perdita del segnale di controllo.
Per abilitare P Mode, spostare il selettore sulla posizione P.
Ci sono tre stati in modalità P .
P-GPS: il GPS funziona meglio quando si è all'aperto, e il Phantom
lo utilizza per librarsi quando il segnale è forte.
P-OPTI: Se il GPS non è disponibile, il velivolo può utilizzare il
sistema di posizionamento Vision per librarsi in modo accurato.
P-A TTI: Nessun segnale GPS e Vision non disponibile. Il velivolo
utilizza allora solo il suo barometro , controllando solo l'altitudine.
N.B. il sistema di posizionamento Vision potrebbe non funzionare
correttamente quando il Phantom sta volando sull'acqua, su super-
fici senza un motivo chiaro, o in ambienti con scarsa illuminazione.
Se il segnale GPS è forte, il velivolo sarà in grado di registrare
un Punto Base e tornarci in caso di necessità. La posizione
GPS viene registrata quando l'icona del segnale GPS in DJI
App Pilot è gialla o verde. Il Phantom 3 tornerà automatica-
mente alla base nei seguenti casi (è necessario un forte se-
gnale GPS):
RTH intelligente: quando si preme il pulsante RTH sul teleco-
mando.
Batteria scarica RTH: l'applicazione DJI Pilot notifica agli utenti
di agire sull' RTH quando il livello della b atteria scen de ad
una determinata soglia.
Failsafe RTH: Quan do il segnale del telec omando viene perso.
● Durante il ritorno, la quota può essere regolata dall'utente per evitare ostacoli. Edifici alti possono influenzare il segnale deltelecomando. La procedura di ritorno Failsafe si attiva se il segnale si perde. Assicurati volare più in alto rispetto a qualsiasiedificio vicino per evitare collisioni.
Phantom 3 Advanced Remote Controller
● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.
2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.
3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.
4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,
radio transmission towers, or Wi-Fi hotspots.
5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when
flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.
6. The Phantom 3 Advanced cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning
system will be operational.
● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which
can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal
performance.
1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and
steel reinforcements underground.
2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
3. DO NOT calibrate beside massive metal objects.
4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after
placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.
Fly Safe Appendice
● P Mode:In this mode, the Phantom 3 Advanced can use GPS and the Vision
Positioning system, allowing it to hover accurately in position indoors
and out. When GPS is available, a Home Point will be locked so that the
Phantom 3 Advanced can Return to Home if the Remote Controller signal
is lost.
※ This Quick Start Guide is subject to change without prior notice.
There are three states in P mode:
P-GPS: GPS works best when outdoors and in a wide open area.
Your Phantom 3 Advanced uses GPS to hover in place when there is
a strong GPS signal.
P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning
system to hover accurately.
P-ATTI: Neither GPS nor the Vision Positioning system are available.
The aircraft will only use its barometer for altitude and other on-board
sensors for attitude stabilization.
Note that the Vision Positioning system may not work properly when
the Phantom 3 Advanced is flying over water, over surfaces without a
clear pattern, or in a low-light environment.
● Return to Home:
When there is a strong GPS signal, the aircraft will be able to
record a Home Point and return to that Home Point when
required. The Home Point location is recorded when the GPS
signal icon in the DJI Pilot app is either yellow or green.
The aircraft will return to the Home Point automatically in the
following scenarios (all require a strong GPS signal):
Smart RTH: When the RTH button on the Remote Controller
or in the DJI Pilot app is pressed.
Low-Battery RTH: A notification will appear in the DJI Pilot
app requesting the pilot to take action when the battery level
falls under a certain level.
Failsafe RTH: When the Remote Controller’s signal is lost.
● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote
Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby
buildings to avoid crashing.
●
;
●
●
● Velivolo
Peso (incluso batteria) 1280 g
Max. velocità in ascesa 5 m/s
Max. velocità in discesa 3 m/s
● Gimbal
Angular Vibration Range Pitch: − 90° to +30°
● Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 30 cm-300 cm
Operating Range 30 cm-300 cm
Operating Environment
●
This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Advanced at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.
Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.
* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending
on conditions in your immediate surroundings.
DJI encourages you to enjoy flying your Phantom 3 Advanced in a safe, responsible, and smart way. To do this, it is important to
understand some basic flight guidelines, both for your protection and for the safety of those around you.
1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above
or near people or animals.
2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to
Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.
3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.
4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)
above ground level, or in line with your local laws and regulations.
Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as
No-Fly Zones.
To enable P Mode, toggle the Flight Mode Switch
to the P position.
It’s time to meet your Phantom.
The Phantom 3 Advanced’s camera records video at up to 1080p/60fps and captures 12 megapixel photos.
Review the diagram below for a full list of your Phantom 3 Advanced’s parts:
FCC ID:SS3-WM3221503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including
interference that may cause undesired operation.
PHANTOM 3
Quick Start GuideV1.0
ADVANCED
Return to home
1. Gimbal and Camera
2. Vision Positioning System
3. Camera Micro-SD Card Slot
4. Aircraft Micro-USB Port
5. Front LEDs
6. Motors
7. Propellers
8. Aircraft Status Indicators
9. Antennas
10. Intelligent Flight Battery
11. Power Button
12. Battery Level Indicators
13. Link Button
14. Camera Micro-USB Port
1211
14
10
13
182 mm
172 mm
105 mm
71 mm
2
7
4
5
9
8
6
3
1
GPS Positioning
28
9.5 mm
289 mm
18
5 m
m
9 feet 10 inches
1 foot
Vision Positioning
Altitude
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. C1/C2 Buttons (Customizable)
18. USB Port
19. Micro-USB Port
1. Power Button
2. Return to Home (RTH) Button
3. Control Sticks
4. Status LED
5. Battery Level LEDs
6. Power Port
7. Mobile Device Holder
8. Small Device Positioning Tabs
(such as mobile phone)
9. Antennas
10. Handle Bar
Folded
Mobile device connection
10
9
87
3
4
5
1
2
6
14
12
1615
11
17
19 18
13
17
Gamma angolo d'inclinazione: -90° a +30°
Posizionamento VisionGamma velocità: <8m/s (altitudine 2 m)Gamma altitudine: 30 cm - 300cmGamma operativa: 30 cm - 300 cmSuperfice operativa: superficie con motivo pulito e adeguata illuminazione
Gimbal
Camera
Velivolo
Peso (incluso batteria) 1280gVelocità max in ascesa 5 m/sVelocità max in discesa 3 m/s
Velocità max assoluta 16 m/s (mode ATTI, senza vento)Max altezza di volo 6000 m.Tempo max di volo approssimativo 23 minutiGamma temperatura operativa da 0° a 40° C
Sensore Sony EXMOR 1/2.3" Pixel effettivi 12.4 M (Totali 12,76 m)
Lenti FOV (campo visivo) 94° 20mm (equivalente a formato 35mm) f2/8Gamma ISO 100-3200 (video) 100-1600 (foto)
Velocità scatto elettronico 8s - 1/8000sMisura max immagine 4000 x 3000
Modalità di scatto: Scatto singo loScatto a raffica: 3/5/7 fotogrammiAuto-Esposizione (Bracketing AEB): 3/5 fotogrammi a 0.7EV BiasTime-lapse
Modalità registrazione video UHD 4096x2160p 24/25, 3840x2160p, 24/25/30 FHD : 1920x1080p 24/25/30/48/50/60
HD : 1280x720p 24/25/30/48/50/60
Max bitrate memorizzazione video : 60 MbpsFile supportati: file FAT32/exTAF - foto JPEG, DNG - video MP4/MOV (MPEG-4 AVC/H.264)SD CARD supportate: Micro-SD, capacità max 64GB - richiesta classe 10 o UHS-1Temperatura operativa da 0° a 40° C
(Lux> 15)
Telecomando
Frequenza operativa 2.400 GHz-2.483GHzDistanza massima di trasmissione 2 km (all'esterno senza ostacoli)Uscita video: porta USBTemperatura operativa da 0° a 40° CBatteria 6000 mAh LiPo 2SSupporto per dispositivi mobili (tablets e smartphones)Potenza trasmissione (EIRP) FCC: 20dbm CE: 16dbmTensione di funzionamento: 1.2 A @ 7.4V
Caricatore
Tensione 17.4VPotenza nominale 100W
Batteria intelligente di volo (PH3-4480 mAh-15.2V)
Capacità 4480 mAhTensione 15.2VTipo batteria LiPo 4SEnergia 68WhPeso netto 365gTemperatura operativa da -10° a 40° CPotenza massima di carica 100W
GPS GPS/GLOMASS