Download - Perfect graphics pvt ltd all products
Perfect Graphics Pvt Ltd
Our objective is to provide our customers with products which enable them to differentiate themselves in the market place, wherever in the world they may be and whatever stage of national economic development.
Our products allow our customers the flexibility to support a diversity of applications. We continue to invest in leading-edge technologies and minimise the total cost of ownership.
Our ultimate aim is to build-up a long and prolific relationship with our customers.
4 Colour Perfecting Printing Unit (4+4)
The WEBKING 4 colour perfecting printing unit is a Common Impression Cylinder (CIC) and 20 cylinder-configured designs where the colour registration does not change during the entire roll unwind period. Experience the colour printing at its best, as never before, with pinpoint registration on both sides of the web irrespective of varying press speeds and varying web tension. A pin register system is built into the plate bender and is carried through into the pin register system built into the plate lock-up. The pin register assures that when installed, the plate is in proper position. In addition, all plate cylinders are equipped with on-the-run side register and circumferential movement for perfect colour registration. Narrow width blanket cylinder provides larger print area. The pneumatic controls ensure ease and speed of operations and the accurate plate punching and bending system ensure utmost accuracy in pre-press operations. The unit being modular in construction other endless possibilities of colour units in configuration of 4+2, 4+1, 2+1, 1+2 etc. are also available to meet the varied requirements. WEBKING Four Colour Perfector - Endless possibilities with profitable solutions!
4 Colour Perfecting Printing Unit (4+4)
Motorized inking system Brush dampening system Shields for brush dampening SS cylinders with ground and
hardened bearers Pneumatic controls for ink,
dampener and impression on/off Pneumatic and/or mechanical
expandable core shaft Pneumatic roll lifting Roll stand with pneumatic disk
brake Web break detectors Plate punch register system Lever type ink keys Double ended plate bender Chilled water circulation system Narrow gap blanket cylinders
4 Hi Printing Unit (4+4) Staggered Blanket Cylinders
Motorized inking system Brush dampening system Shields for brush dampening
(optional) SS cylinders with ground and
hardened bearers Pneumatic controls for ink,
dampener and impression on/off Pneumatic and/or mechanical
expandable core shaft Pneumatic roll lifting Roll stand with pneumatic disk
brake Web break detectors Plate punch register system Lever type ink keys Double ended plate bender Chilled water circulation system Narrow gap blanket cylinders Cut-off size available 546mm
2 Colour Perfecting Printing Unit (2+2)
The WEBKING 2 CP is the perfect example of proven technology. Specially designed for BOOK PRINTING the WEBKING 2 CP printing unit is a Common Impression Cylinder (CIC) and 10 Cylinder configured design where the colour registration does not change during the entire roll unwind period. Colour register is maintained even with varying press speeds or with varying web tension. It brings you the magic of full colour, as never before, with pinpoint registration on both sides. It is fast and easy, has simple plate lock-up and has facilities for on-the-run pin register adjustments. The precisely ground and hardened bearers provide constant reference surface for perfect accuracy of cylinder impression. A pin register system is built into the plate bender and is carried through into the pin register system built into the plate lock-up. The pin register assures that when installed, the plate is in proper position. In addition, all plate cylinders are equipped with on-the-run side register and circumferential movement for perfect colour registration. The pneumatic controls ensure ease and speed of operations and the accurate plate punching and bending systems ensure utmost accuracy in pre-press operations.
2 Colour Perfecting Printing Unit (2+2)
Motorized inking system Brush dampening system Shields for brush dampening Bearer to bearer plate and
blanket cylinders Pneumatic controls for ink,
dampener and impression on/off Pneumatic and/or mechanical
expandable core shaft Pneumatic roll lifting Roll stand with pneumatic disk
brake Web break detectors Plate punch register system Lever type ink keys Double ended plate bender Chilled water circulation system
4 Colour Satellite Printing Unit (4+0)
The WEBKING QUADRACOLOUR satellite printing unit has been proven by the industry as the finest for high quality, low wastage, four colour printing consistently page after page. It’s flexibility and versatility is unlimited. It is ideal for the production of a variety of jobs ranging from 4 colour newspapers and posters to magazines etc with super speed and minimum wastage. Designed on the principle of “Common Impression Cylinder” (CIC), it is fast and easy, has simple plate lock-up and has facilities for on-the-run pin register adjustments. The precisely ground and hardened bearers provide constant reference surface for perfect accuracy of cylinder impression. A pin register system is built into the plate bender and is carried through into the pin register system built into the plate lock-up. The pin register assures that when installed, the plate is in proper position. In addition, all plate cylinders are equipped with running lateral and circumferential adjustment for perfect colour registration. The pneumatic controls ensure ease and speed of operations and the accurate plate punching and bending systems ensure utmost accuracy in pre-press operations.
4 Colour Satellite Printing Unit (4+0)
Motorized inking system Brush dampening system Shields for brush dampening Bearer to bearer plate and
blanket cylinders Pneumatic controls for ink,
dampener and impression on/off Pneumatic and/or mechanical
expandable core shaft Pneumatic roll lifting Roll stand with pneumatic disk
brake Web break detectors Plate punch register system Lever type ink keys Double ended plate bender Chilled water circulation system
Perfecting PrintingUnit (1+1)
A robustly constructed unit using solid side frames of 50mm thickness of graded casting that ensures long residue life of the machine. Reliable enough to understand deadlines to the tee. The horizontal main drive at blanket cylinder level is mounted on anti-friction bearings. The high line position provides a direct drive to the printing units. The power is transmitted through helical gears throughout the printing unit. The assembly is lubricated by a pressurized oil circulation system. Clutches are provided to individually silence either folder or printing units. The precisely ground and hardened bearers provide constant reference surface to perfect accuracy of cylinder impression. Plate and blanket cylinders are statically and dynamically balanced to ensure trouble free running of the machine at highest speed. The unit is available either with manual or with pneumatic controls and is equipped with a host of other advanced features.
Perfecting PrintingUnit (1+1)
Motorized inking system Brush dampening system Shields for brush dampening Bearer to bearer plate and blanket
cylinders Pneumatic controls for ink,
dampener and impression on/off Pneumatic and/or mechanical
expandable core shaft Pneumatic roll lifting Roll stand with pneumatic disk
brake Web break detectors Plate punch register system Lever type ink keys Double ended plate bender
Broadsheet/TabloidFolder
The WEBKING presses are equipped with a standard single former heavy duty 2:1:1 jaw type folder. One tabloid slitter is located on the roller, top of the former. It is also equipped with an electronic copy counter, and a standard motor driven delivery table. The mechanical clutch disengages the folder from the main drive shaft thus allowing the units to run with the webs led through the press and the folder remaining at a stand still. This feature is particularly useful during make ready time and also the printing unit to be run in reverse direction to facilitate plate removing. The folding mechanism consists of one cutting cylinder, one double dia folding drum, one jaw cylinder, one pair of driven folding rollers and one fan delivery.
Other folding options available are: (1) High speed reciprocating and rotating chopper type Quarter Page Folder with Creaser and Parallel Perforator (2) Double Parallel Folding System with Cross Perforator.
Broadsheet/TabloidFolder
2:1:1 jaw type Electronic counter Standard and/or motorized
delivery table Pneumatic pull through
assembly at RTF Half fold kicker Air former Balloon / Upper former Bay Window Turner Bar
Bay Window
Turner Bar
Metal Halide PrintingDown Frame
The OHX / INS Printing Down
Frames have been in the field for
over one and half decades with
major newspapers and commercial
printers as customers. A wide range
suited and tailored for the industry
has been our specialty. Forays into
infrared and UV conveyer systems
have also been successful.
Metal Halide PrintingDown Frame
PLATE SIZE 25X36", 37X45", 45 X 55"
TRANSFORMER THERMALLY PROTECTED
MODE OF OPERATION BOTH AUTOMATIC AND MANUAL OPTIONS
EXPOSURE COMPUTER MICROPROCESSOR BASED, 9 CHANNEL
LIGHT INTEGRATOR FOR UV OUTPUT COMPENSATION WITH
AGEING OF LAMP
INPUT VOLTAGE VARIATION VOLTAGE TAP SELECTOR FOR SELECTING
INPUT VOLTAGE RANGE
INSTANT & SHUTTER SYSTEMS IMPORTED REFLECTORS FOR COLLAMATION
MODEL DIMENSION (mm) EXPOSURE SIZE POWER REQUIREMENT GROSS WT
OHX/ INS 4070 1050X850X2270 700 X 950 mm 440 V 50HZ, 3 PH, 6 KVA 300 Kgs
OHX/ INS 4095 1250X1050X2270 950 XI 150 mm 440 V 50HZ, 3 PH, 6 KVA 350 KgsFTX/ FTi 4070 1420 X 970 X 1220 700 X 950 mm 440 V 50HZ, 3 PH, 6 KVA 400 KgsFTX / FTXi 4095 1620X1170X1220 950 XI 150 mm 440 V 50HZ, 3 PH, 6 KVA 450 Kgs
Conventional OffsetPlate Processor
The DPX conventional plate
processor is a rugged completely
automatic machine for both positive
and negative offset plates. A unique
worm & worm wheel drive system is
precise and self lubricating. The
plate processor is provided with a
rewash slot for finishing and drying.
It helps preserve the plate for future
jobs and also deletion. The front
panel has an easy to use
microprocessor with LCD display.
Conventional OffsetPlate Processor
MAX PROCESSING WTDTH 660/ 860/ 1150 MM
MIN PROCESSING LENGTH 450 MM
PLATE THICKNESS 0.15-0.40 MM
DEVELOPER TANK CAPACITY 15 LIT
PLATE PROCESSING SPEED 50 - 200 CM/ MIN
DEVELOPER REPLENISHMENT AREA / PER PLATE / LEVEL BASED
CHILLER STANDARD
DEVELOPER TEMPERATURE 18-35C+/ -2C
DRIER TEMPERATURE ROOM TEMPERAUTE - 70 C
FRONT PANEL LCD DISPLAY
DEVELOPER TANK DIP TANK WITH SUBMERGED BRUSH
MODEL DIMENSION (mm) PROCESSING POW ER REOUIREM ENT GROSS WT
WIDTH (mm)
DPX 660 1270X2600X1190 660mm 220 V 50/ 60 HZ, 3 KW 275 Kgs
DPX 860 1470X2600X1190 860mm 220 V 50/ 60 HZ, 3 KW 300 Kgs
Thermal CTPPlate Processor
The CPX Thermal Plate Processor is
an economical, robust and easy to
use processor for all kinds of
Thermal plates. The polypropylene
tank construction is corrosion
resistant and easy on maintenance.
Some special user friendly features
like auto clean, fluid handling
system and plate program are
incorporated. A software diagnostic
package provides faster service.
Parameters for all leading plate
brands can be pre-programmed and
stored in memory.
Thermal CTPPlate Processor
MAX PROCESSING WIDTH 860 MM
MIN PROCESSING LENGTH 450 MM
PLATE THICKNESS 0.15-0.40 MM
DEVELOPER TANK CAPACITY 38 LIT
PLATE PROCESSING SPEED 20 - 200 CM/ MIN
DEVELOPER REPLENISHMENT AREA / PER PLATE / LEVEL BASED
CHILLER STANDARD
DEVELOPER TEMPERATURE 18-35C+/ -2C
DRIER TEMPERATURE ROOM TEMPERAUTE - 70 C
MICROPROCESSOR BASED PLATE PROGRAMMING FACILITY
FRONT PANEL LCD DISPLAY
DEVELOPER TANK TWIN BRUSH ADJ USTABLE
FINISHER RECYLABLE
WASH SECTION BRUSH FOR PLATE WASH
FLUID HANDLING SYSTEM WASH AND CLEAN
MODEL DIMENSION (mm) PROCESSING- POWER REQUIREMENT GROSS WT
WIDTH (mm)
CPX 660 1540X1070X1050 660mm 220 V 50/ 60 HZ, 50A 350 Kgs
CPX 860 1540X1270X1050 860 mm 220 V 50/ 60 HZ, 50A 400 Kgs
Violet/PhotopolymerCTP Plate Processor
The VPX Violet Photopolymer plate
processor is state of the art processor
for all kinds of photopolymer plates.
The polypropylene tank construction
is corrosion resistant and easy on
maintenance. Easy to remove roller
system helps maintain the equipment.
The pre-heat section is accurate to +/-
2C using infrared ceramic heaters.
Special fan spray in the wash section
ensures a clean plate on exit.
Violet/PhotopolymerCTP Plate Processor
MIN PROCESSING LENGTH 350 MM
PLATE THICKNESS 0.15-0.40 MM
PRE HEAT TEMPERATURE ROOM TEMPERATURE - 120 C
PRE WASH BRUSH & WATER @ 2.5 BAR
DEVELOPER TANK CAPACITY 24 LIT
PLATE PROCESSING SPEED 120 CM/ MIN (19 SEC DWELL TLME)
DEVELOPER REPLENISHMENT AREA / PER PLATE / LEVEL BASED
DEVELOPER TEMPERATURE 18-35C+/ -0.5C
MICROPROCESSOR BASED PLATE PROGRAMMING FACILITY
FRONT PANEL LCD DISPLAY
FINISHER RECYLABLE
WASH SECTION FAN SPRAY @, 2.5 BAR
MODEL DIMENSION PROCESSING POWER REQUIREMENT GROSS WT
(mm) WIDTH (mm)
VPX 660 1880X1150X1400 660mm 220 V 50/ 60 HZ, 50A 525 Kgs
VPX 860 1880X1350X1400 860mm 220 V 50/ 60 HZ, 50A 600 Kgs
Inline FlexoProcessor
The FPX Inline Flexo Processor is
designed for the washout treatment of
flexography photopolymer plates. The
equipment is completely enclosed to
minimize exposing operators to the
chemical fumes and also is provided with
a built-in exhaust. It allows usage of all
types of solvents like perchloroethylene
and derivatives. The unique combination
of flat and rotary brushes gives the best
of both processes.
Inline FlexoProcessor
MAX PLATE SIZE 900 X 1016 mm ( 35.4" X 40")
CONNECTIVITY HIGH SPEED I2C
BRUSH TYPE FLAT AND ROTARY COMBINATION
SOLVENT TYPE OPTION TO WORK WITH DIFFERENT SOLVENTS
TANK CAPACITY OPTION TO WORK WITH TWO DIFFERENT TANK
CAPACITIES
FAULT INDICATION AUDIO VISUAL. ALARM
COUNTERS HOUR COUNTER AND PLATE COUNTER
CLEANING FEATURE SELF CLEANING WITH FRESH SOLVENT
DRIVE SPEED 4 - 40 CMS/ MIN
PLATE LENGTH INDICATOR IN Cms
CHEMICAL LEVEL CONTROLED WITH SENSORS
MAX PLATE THICKNESS 7 mm
MAX PLATE SIZE 900X1016 mm
WASHOUT TANK CAPACITY 80 LIT
OVERALL DIMENSION 2620 XI 540X1165 mm
WEIGHT 650 Kgs
ELECTRICAL SPEC 220 v, 50/ 60 Hz, 20A
Flexo Exposure, DrierAnd Light Finisher
The EDLF (Exposure, Drier and Light
Finisher) is yet another master piece
for perfect exposure and finishing of
Flexography plates. With bearing
slides on drier racks, careen sheet,
and special matt sheet for the
vacuum bed, its quality all the way.
The lamp fault indicator stops all
plate wastage. The light finisher is
on easy slide drawer with the power
pack hatch on the back for easy
servicing.
Flexo Exposure, DrierAnd Light Finisher
EXPOSURE LAMPS 80 W UVA
LIGHT FINISHING LAMPS 36WUVC
DRIER HEATER WATTAGE 4KW
DRIER TEMPERATURE 60 DEG C
VACUUM PUMP MAINTENANCE FREE
PROGRAMMING MICROPROCESSOR BASED MEMORY CHANNEL
MANUAL CONTROLS PROVIDED ADDITIONALLY FOR MAIN, BACK
EXPOSURE AND FINISHER
FAULT INDICATORS LED FAULT INDICATORS FOR INDIVIDUAL LAMPS
TECHNICAL DATA EDLF 3040 EDLF 3648
MAX PLATE SIZE 762X1016 mm 914X1220 mm
UVALAMP 16 X 10R 80W 20 XI OR 80W
UVCLAMP 13XTUV36W 15XTUV36W
OVERALL DIMENSION . 1475X1640 XI 145 mm 1625X1840 XI 145 mm
WEIGHT 300 Kgs 400 Kgs
ELECTRICAL SPEC 220 v, 50/ 60 Hz, 40A 220 v, 50/ 60 Hz, 45A
Color Proofing Table
CK 2536 PROOF LITE FOR COLOUR PROOFING PLATE INSPECTION Max Plate Size 25x36” 6500 K Cool Day Light CRI Maintained @90 Asymmetrical Reflectors Imported Reflectors Cooling For Lamp Life Hour Counter Lamp Change Indicator 4 Drawers for Storage
Single VendNewspaper Vending Machine
Intelligent-Special toggle for Weekday and Weekend pricing
Maintenance free Layman stacking ease Separate coin box for independent
collections NO STOCK annunciation-load & clear WELL LIT ADD-ON BILL BOARDS Capacity – 50-75 copies Built-in sensor for varying stock
thickness Light barrier enabled paper dispenser Maximum size – 280 x 350 mm 50,000 hours of active signage Precise pulse recognition of coins
OPTIONS
Currency to coin changers Verifiable circulation data collection
with microprocessor based USB retrieval
Smart Card, loyalty reward programs
G5 Press G5 is a variable cut off press for semi
commercial and security printing jobs like book covers, cheques, lottery tickets, wrappers, OMR forms, computer forms & much more.
The print unit is capable of accepting wet offset, dry offset, letterpress, numbering and flexo printing inserts for different repeat lengths.
Straight pass web gives set-off free print results. The web can be threaded alternatively for interdeck UV drying while printing on coated stocks. Continuous dampening (Dahlgren type) adds to the brilliance of print.
With an unmatched repeat range and a large spectrum of stock thicknesses that can be accommodate; this press coupled with multiple delivery options is a true winner!
EleganceBusiness Forms Press
The requirement for computer forms is no longer standard - it comes in an unlimited configuration of shapes, sizes and colours. Check out the huge inventory of invoices, tickets, cheques, pay slips, share certificates, application forms or EZR stock forms at almost any commercial establishment and you would know.
Elegance lets you handle mind-boggling combinations with superlative ease - allowing you to cater to variable print runs - from micro to macro - facilitating quick changes of form-length, colour, plate and paper.
More importantly, the variable circumference is customised to your configuration of wet offset, dry offset, letterpress printing or a combination to suit market requirements of varying runs with low wastage.
Rotary FormsConverter
A compact machine for producing stock forms in single color (numbering & logo can be in different color).
The paper reel is unwound in the unwind unit which incorporates an automatic tension control and length control. It then passes on into the printing unit where printing is done on one side. Further on, in the processing unit, the paper is perforated (across and along it's length), sprocket punched and then zigzag folded to produce packets of continuous forms.
Very simple to operate, this machine has all the features to produce a full featured stock form. The printing unit is letterpress based and change of print repeats is quick and convenient.
Ecoflex Ecoflex is a narrow web flexo press for
printing labels, tags, flexible packaging, cartons, etc. Its modular design and precise, rigid construction provide the versatility and reliability necessary for the most difficult jobs.
The Multitec Ecoflex flexography press can be assembled to your specifications in various widths. A full range of options further enhances the versatility of the Ecoflex label press and its ability to handle a variety of applications on a broad range of materials.
The Ecoflex is constructed to provide a superior foundation for quality printing and converting. It has full dual side frames to create a solid and rigid structure not attainable with partial frames supported on sheet metal legs or with cantilevered designs.
Consistent, repeatable quality printing is facilitated by the ease of operating the Ecoflex. Precise print adjustments are made quickly, even when changing material caliper. Anilox rolls can be changed quickly even after the job is set up, and the closed loop tension system provides exact and repeatable control at the operator selected tension level.
Multiflex
Take a giant leap in technology with
Multiflex - a narrow web flexo press
suited for production of FMCG / Pharma /
Brewery labels, packaging products, etc.
The Multiflex flexographic printing press
can take care of your production of prime
labels, cartons, and many other
products.
Various in-line options like hot foil
stamping, embossing, delam-relam, etc
makes this press a true winner.
Various delivery options - rewinder,
sheeter-stacker or zigzag folder - all are
possible to give you an unmatched
productivity with flexibility of quick
change between your various production
programs.
Label Converter
The Label converter is a compact
machine for producing simple labels. It
can cater to the production of barcode,
price, marking, addressing and other
stock labels.
The Label Converter has several in-line
converting options like die-cutting and
waste matrix rewinding, perforating,
sprocket hole punching, etc. It can also
have a flexo printing unit.
Modular design enables extension from a
basic startup machine to a full fledged
narrow web label printing solution.
Delivery options include roll to roll
production, roll to sheet or roll to zigzag
fold.
Precision Sheeter
Cut-size sheeting lines for A4, A3, FS,
etc. sized sheeting. Auto-cycle based
production where you just set in the
batch size and the machine does the
rest. Batches of the specified no. of
sheets are separated and are ready to
be packed.
Minimum wastage ensures higher
profitability than guillotine cut where
all four sides of the big sheets have to
be finished.
Narrow Width Slitter
To make narrow width products in
reel form from pre-printed / stock
reels (for example ATM, POS, cash
register rolls, etc.).
Also to inspect & doctor pre-printed
reels.
Baling Press
An investment that will pay for itself
in a short span of time and keep the
sea of waste paper from engulfing
your efficiency.
Considering the economy in transport
costs and the resultant saving, can
you afford not to buy one?
Works for paper, corrugated board,
printer's waste and film, etc
Slitter RewinderFor Stock Reels
Save expensive paper that has been damaged during transit or has got out of shape during loading / unloading and will not let you run your web press at the desired high speeds.
Join those reel ends you always thought were scrap and get a workable reel out of it.
And of course, slit stock reels to different sizes to cater to the variety of jobs that involve different web widths.
Model ZM is for web width of 40" and Model ZL is for 63" web width. Both of these machines have a center drive system on the finished reel. For higher web widths, we have Drum Type Rewinder that work on surface drive systems.
Collator
A simple and easy to operate machine for
making multiple part computer
(continuous) forms with or without
interleaved carbon paper.
The web travels with the help of pin-
feeder and gets crimped at an interval of
4".
A perfect companion for your forms press.
Video Plate Mounter
Video Plate Mounter for easy and quick mounting of flexo and letterpress plates.
High resolution camera, monitor LCD TFT
Accurate liner rail ensures mounting accuracy
Movable plate cylinder holder
Available for mounting on sleeve
Fast and easy mounting process, improve productivity
For flexo press and rotary letterpress. Also available for plate mounting for wide-web printing.
Contact us
For more information, please write to us at:
PERFECT GRAPHICS PVT LTD1844/10 Govindpuri Extension, Kalkaji
New Delhi – 110 019, IndiaPhone: +91.11.26025372, 26025468
Fax: +91.11.26025468Email: [email protected] & [email protected]
Web Site: www.pg-pl.com