HBUD Series LED High BayImportant: Read all instructions prior to installation.

User ManualPart Number:

Dimensional Drawings

Rev Date: V1.0 10/27/2017Rev Date: V1.0 10/27/2017

5yr

HBUD-50K100W, HBUD-50K150WHBUD-50K200W, HBUD-50K300W

HBUD Series LED High BayUser Manual

Part Number:HBUD-50K100W, HBUD-50K150W, HBUD-50K200W, HBUD-50K300W

HBUD-50K100W HBUD-50K150W

HBUD-50K200W HBUD-50K300W

5.12in130.16mm

6.05in153.67mm

10.95in278.13mm

8.69in220.73mm

7.19in182.63mm

6.00in152.40mm

6.03in153.26mm

10.95in278.13mm

8.69in220.73mm7.19in

182.63mm

6.00in152.40mm

6.03in153.26mm

10.95in278.13mm

8.69in220.73mm7.19in

182.63mm

7.52in191.13mm

6.03in153.26mm

8.69in220.73mm

10.95in278.13mm

7.19in182.63mm

7.52in191.13mm

6.03in153.26mm

8.69in220.73mm

10.95in278.13mm

7.19in182.63mm

6.35in161.29mm

12.63in320.91mm

12.64in321.01mm

9.61in244.09mm

7.95in201.98mm

User ManualPart Number:

HBUD series LED High BayImportant: Read all instructions prior to installation.

Included Parts

Specifications

Optional Accessories

1 - High Bay Light 1 - Eye Bolt 1 - Washer

Microwave Motion Sensor (HBUD-MS)PC Reflector (HBUD-8-PR)U-Bracket (HBUD-8-UB)

Rev Date: V1.0 10/27/2017

Product HBUD-50K100W HBUD-50K150W HBUD-50K200W HBUD-50K300WIntensity 13000 lm 19500 lm 26000 39000Operating Voltage Range 100~277 VAC 100~277 VAC 100~277 VAC 100~277 VACWattage 102W 152W 206W 313WBeam Angle 120 degree 120 degree 120 degree 120 degreeColor Temperature 5000 K 5000 K 5000 K 5000 KCRI >80 >80 >80 >80Operating Temperature -22~122°F (-30~50 °C) -22~122°F (-30~50 °C) -22~122°F (-30~50 °C) -22~122°F (-30~50 °C)IP Rating Weatherproof IP65 Weatherproof IP65 Weatherproof IP65 Weatherproof IP65LED Lifetime 54,000 Hours 54,000 Hours 54,000 Hours 54,000 HoursDimmable 1~10V 1~10V 1~10V 1~10VPower Factor >0.93 >0.93 >0.93 >0.93Fixture Weight 7.5 lbs (3.40Kg) 8.3 lbs (3.76Kg) 9.5 lbs (4.30Kg) 15 lbs (6.8Kg)Standards and Certifications CE, RoHS, UL, FCC, DLC CE, RoHS, UL, FCC, DLC CE, RoHS, UL, FCC, DLC CE, RoHS, UL, FCC, DLCWarranty 5 Years 5 Years 5 Years 5 Years

Eye Bolt Installation Instructions

U-Bracket Installation Instructions

PC Reflector Installation Instructions

Motion Sensor Installation Instructions

HBUD-50K100W, HBUD-50K150WHBUD-50K200W, HBUD-50K300W

1. Insert Eye Bolt and Washer into threaded hole on back of fixture and tighten. Hang fixture by attaching Eye Bolt (Fig. 1) to an existing hook or carabiner.

2. Connect the fixture wires to the corresponding wires in the junction box (not included).

Black

White

Green

BlackL L

N N

GND GND

White

Green

Warning

Wiring Diagram

• This product should be installed by a fully certified electrician in accordance with local building and electrical codes.

• Due to risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.

• Failure to properly support the fixture during installation may cause damage or injury, for which the manufacturer is not responsible. Ensure the light bracket/eye bolt is securely mounted and will support the weight of the fixture.

1. Secure mounting plates to fixture with provided 4 x 21mm allen screws using 4mm allen wrench (A). Attach U-Bracket to mounting plate with 2 x 27mm allen screws and nuts using 6mm allen wrench (B).

2. Position desired angle of U-Bracket and secure with 2 x 4mm allen screws (C).

3. Mount Fixture to surface.4. Connect wiring to power supply. Black to Line, White to

Neutral, and Green to Ground.5. Restore power to circuit to test function.

1. Remove power prior to installation.2. Motion sensor and compact J-Box come attached to mounting

plates. Position motion sensor and provided compact J-Box on opposite sides of the light.

3. Attach motion sensor to light using 2 x 21mm Allen Screws using 4mm allen wrench (A).

1. Turn fixture upside down.2. Line up 3 holes from PC Reflector

to 3 threaded holes on light. 3. Screw 3 phillips screws to secure

PC Reflector

MotionSensor

Compact J-Box

From LED

1-10VDimming

Wires From LED

Power Source

Threaded Holes for PC Reflector

Threaded Holes for PC Reflector

(B)

(C)(B)

(C)

(A)(A)

4. Attach compact J-Box to light using 2 x 21mm Allen Screws using 4mm allen wrench (B).

5. Make wiring connections according to diagram.

6. Connect to power source. Black to Line, White to Neutral, and Green to Ground.

7. Restore power to circuit to test motion sensing functionality. *Note: Refer to motion sensor manual for operation.