Download - Oc679 Acoustical Oceanography
1
Oc679 Acoustical Oceanography
Sonar Equation
Parameters determined by the Medium• Transmission Loss TL
• spreading • absorption
•Reverberation Level RL (directional, DI can’t improve behaviour)
•Ambient-Noise Level NL (isotropic, DI improves behaviour)
Parameters determined by the Equipment• Source Level SL• Self-Noise Level NL• Receiver Directivity Index DI• Detector Threshold DT (not independent)
Parameters determined by the Target• Target Strength TS• Target Source Level SL
2
terms are not very universal!
3
Oc679 Acoustical Oceanography
Units
N = 10 log10 where I0 is a reference intensity
the unit of N is deciBels
so we might say that I and I0 differ by N dB
in terms of acoustic pressure, (p/p0)2 I/I0
where the oceanographic standard is p0 = 1 Pa in water
we can write this in terms of pressure as 20 log10
0
I
I
0
p
p
p/p0 dB = 20log10 p/p0
1 0 √2 3 (double power level) 2 6 4 12 10 20 20 26 100 401000 60
for comparison:• atmospheric pressure is 100 kPa• pressure increases at the rate of 10 kPa per meter of depth from the surface down
compare p/p0=1/√2, I/I0 = ½dB = -3we might say the -3dB level or ½ power level
4
1 Pa is equivalent to 0 dB
5
20
Pa
1 P
a
1 Pa is the reference standard for water20 Pa is the reference standard for air
20log20 = 26 dB
6
large target(relative to λ)
Scattering
small target(relative to λ)
(Rayleigh scattering)
7
scattering of light follows essentially the same scattering laws as sound
but light wavelengths are much smaller than sound - O(100s of nm)
almost all scattering bodies in seawater are large compared to optical wavelengths and have optical cross-sections equal to their geometrical cross-sections Large Targets
the sea is turbid to light
on the other hand, acoustic wavelengths are typically large compared to scattering bodies found in seawater (at 300 kHz, 5 mm, 4 orders of magnitude larger) - acoustic scattering is dominated by Rayleigh scattering Small Targets
by comparison the sea is transparent to sound - what limits the propagation of 300 kHz sound is not scattering but absorption
Scattering
8
Oc679 Acoustical Oceanography
Absorption
in a homogeneous medium, a plane wave experiences an attenuation of acoustic pressure the original pressure and to the distance traveled – this is represented by a bulk viscosity in the N-S equations which applies only to compressible fluid (this is distinct from a shear viscosity – M&C sec 3.4.2)
this is due To wave absorption (energy lost to heat) e is the amplitude decay coefficient
absorption losses are due to ionic dissociation that is alternately activated and deactivated by sound condensation and rarefaction • the attenuation by this manner in SW is 30x that in FW• dominated by magnesium sulphate and boric acid
-0
eRp p e
acoustic absorption absorption typical profiling frequency @S=0 @S=35 range
3000 kHz 2.4 dB/m 2.5 dB/m 3-6 m1500 kHz 0.60 dB/m 0.67 dB/m 15-25 m 500 kHz 0.07 dB/m 0.14 dB/m 70-110 m
source: Sontek ADCP manual
TL
9
TL
10
TL
11
Oc679 Acoustical Oceanography
relate spherical spreading & range attenuation due to absorption in terms of sonar equation
spherical spreading 1/R2, that is
log10 I/I0 = log10 R02/R2 = log10R0
2 – log10R2
but since typically I0 is referred to 1 m range from source, log10R02=0
and 10log10 I/I0 = – 20log10R
range attenuation related by p = p0e-R, or I = I0e-2R
then 10log10 I/I0 = - 20R
and together these represent a transmission loss
TL = -20log10R - 20R
202
0
RI
I R
spherical spreadingabsorption
TL
12
Oc679 Acoustical Oceanography
Spreading
cylindrical spreading is an approximation to propagation through sound channel
analogue is propagation through medium with plane-parallel upper and lower bounds
this is important for long range transmission through sound channel – since the loss is now 1/R rather than 1/R2, propagation is more efficient
this doesn’t happen
TL
13
SpreadingSpreading
• Spreading– Due to divergence– No loss of energy– Sound spread over wide area– Two types:
• Spherical– Short Range: R < 1000m
– TL (dB) = 20 log R
• Cylindrical– Long Range: R > 1000m
– TL (dB) = 10 log R + 30 dB
Spherical component
TL
14
Oc679 Acoustical Oceanography
0 012
0 012
0 0 12log log log log log log
R
rec
Rrec
rec
p Rp e R
R
p S V
p RS V e R
R
S V p R R R R
p is the pressure at range RR12 is the target reflection coefficient
Srec is the receiver sensitivity [ Pa/V ]V is the voltage o/p measured at receiver
0
RS RL SL TL TS
this is the voltage measured at the receiver – more commonly this would be in counts, which is then converted to volts
now consider the reflected signal from a target with reflection coefficient R12
15
0 012
0 0 12log log log log log log
Rrec
rec
p RS V e R
R
S V p R R R R
this is the physical relationship that we have developed
this is how that relationship is represented logarithmically
terms in the SONAR EQUATION represent logarithms
16
let’s take a step back now that we have seen how the SONAR EQUATION is formed
the physics is straightforward as is the transformation to a logarithmic equations – more straightforward than is implied by the large number of variations to the SONAR EQUATION that appear – these are usually specific to the application and intended for unambiguous use by operators
we’ll look at a couple of variations
17
Passive SONAR EQUATION
passive sonars listen only
purpose – detection, classification and localization of an acoustic source
in turn, a particular source is embedded in a sea of sources
suppose a radiating object of source level SL (decibels) is received at a hydrophone at a lower signal level S due to transmission loss TL (TL always > 0)
S = SL – TL
where we have already defined TL = 20log10R + 20R to be due to the product of absorption and spreading (which appear additively in this logarithmic representation)
and we could represent the signal to noise ratio at the hydrophone as
SNR = SL – TL – N logarithmic representation of
this is the logarithmic representation of 0 0 Rp Rp e
R
0 0 R
Noise Noise
p Rep R
18
SNR can be increased by beam-forming so that sound does not spread spherically but is more directional
for an omnidirectional source I is proportional to 4πR2
here it is constrained to πr2 where r might be the piston diameter of a cylindrical source
Define DI = 10log(intensity of acoustic beam/intensity of omnidirectional source)
DI = 10 log ((p/πr2)/(p/4πR2))
SrR = 1 m
r
α/2
with R = 1 DI = 10 log (4/r2) and tan(α) = r/R = r
DI = 10 log (4/tan2(α/2))
DI directivity index
19
SNR can be increased by beam-forming produced by an array of transducers (perhaps in a single head or maybe distributed geographically)
the directivity index DI represents this advantage for a particular array so that
SNR = SL – TL – N + DI
ideally, detection is possible when the signal is sufficiently close and not disguised by noise …
that is, when SNR > 0however, due to the nature of the signal, interference, the sonar operator’s training and alertness, etc … something more than 0 is necessary
this extra appears as a detection threshold, DT
we now write the SONAR EQUATION in terms of a signal excess SE
SE = SL – TL – N + DI – DT
this is now the difference between the actual received signal at the output of the beamformed array and minimum signal required for detection
20
if DT set to be too high, only targets with high source levels are detected. Detection may be difficult but the probability of a false alarm is low as well.On the other hand, if DT is too low, the probability of false alarms increases
21
Looking at a single trace on an oscilloscope is a little antiquated.A time history helps to see what’s going on.
22
Active SONAR EQUATION
now the transducer transmits a signal that is reflected or scattered from an object – the modified signal is sensed at the receiver (which may be the same as the source, in monostatic mode)
this modified signal must be extracted from the background interference which is not only the sonar noise and ambient noise, but also the reverberation generated by the original signal
simple example – travel-time measurement of the echo to estimate the distance to an object (such as a fathometer which measures water depth by listening to the echo of a ping off the sea floor)
we can simply say that the sound pressure level SPL at range R is
SPL = SL - TL
23
three principal differences from passive case
1. received signal level modified by target strength TS
2. reverberation is the dominant interference
3. transmission loss results from 2 paths transmitter to target + target to receivermonostatic - transmission loss is 2TLbistatic - transmission loss is TL1 + TL2
Reverberation Level RL
results primarily from scattering of the transmitted signal from things other than the target of interest boundary scattering may be due to waves, ice bottom featuresvolume scattering may be due to zooplankton, fish, microstructure, …
this means that the total interference term is due to the sum of the noise and the reverberation N + RL – these act to diminish our ability to detect TS
24
http://wart.coas.oregonstate.edu/Documents/for%20others/jim/150W.gif
Homework 1 – Martin Hoecker-Martinez 18 Jan 2011
25
So, there are essentially two types of background that may mask the signal that we wish to detect:
1) Noise background or Noise Level (NL). This is an essentially a steady state, isotropic (equal in all directions) sound which is generated by amongst other things wind, waves, biological activity and shipping. This is in addition to transducer system self-noise. (Wenz curves)
2) Reverberation background or reverberation level (RL). This is the slowly decaying portion of the back-scattered sound from one's own acoustic input. Excellent reflectors in the form of the sea surface and floor bound the ocean. Additionally, sound may be scattered by particulate matter (e.g. plankton) within the water column. You will have experienced reverberation for yourself. For example if you shout loudly in a cave you are likely to here a series of echoes reverberating due to sound reflections from the hard rock surfaces. These reverberations decay rapidly with time.
Although both types of background are generally present simultaneously it is common for either one or the other to be dominant.
26
we could define SONAR EQUATION for a monostatic system as
SE = SL – 2TL + TS – (RL + N) + DI – DT
And for a bistatic system
SE = SL – TL1 + TS – TL2 – (RL + N) + DI – DT
27
Oc679 Acoustical Oceanography
Sound scattered by a body - RL in SONAR EQUATION
scattering is the consequence of the combined processes of reflection, refraction and diffraction at surfaces marked by inhomogeneities in c - these may be external or internal to a scattering volume ( internal inhomogeneities important when considering scattering from fish, for example )
net result of scattering is a redistribution of sound pressure in space – changes in both direction and amplitude
the sum total of scattering contributions from all scatterers is termed reverberation
this is heard as a long, slowly decaying quivering tonal blast following the ping of an active sonar system
consideration usually begins by considering scattering from spheres
28
Oc679 Acoustical Oceanography
reverberation following explosive charge
initial surface reverb is sharp, followed by tail due to multiple reflection & scattering
then volume reverb in mid-water column (incl. deep scattering layer)
then bottom reflection, 2nd surface reflection, and long tail of bottom reverb
explosive source at 250 mnearby receiver at 40 mbottom depth 2000 m
direct signal
29
Oc679 Acoustical Oceanography
sounds in the sea or N in the SONAR EQUATION
natural physical sounds
natural biological sounds
ships
30
Oc679 Acoustical Oceanography
thick black line – empirical minimum
A - seismic noise
B – ship noise (shallow water)
C – ship noise (deep water)
H – hail
W – sea surface sound at 5 wind speeds
R1 – drizzle (1 mm/h) 0.6 m/s wind over lake
R2 – drizzle, 2.6 m/s wind over lake
R3 – heavy rain (15 mm/h) at sea
R4 – v. heavy rain (100 mm/h) at sea
F – thermal noise (f1) - molecular
Wenz curves used to determine ambient noise
31
Oc679 Acoustical Oceanography
on-axis source level spectra of cargo ship at 8 & 16 kts measured directly below ship – this represents the details of what we saw in the compilation slidesB – propeller Blade rateF – diesel engine Firing rateG – ship’s service Generator rate
32
Oc679 Acoustical Oceanography
c(z)
propagation of coastal shipping noise into deep sound channel
this is due to c(z) profile over the shelf, causing a progression of sound down the slope until the axis of the deep sound channel is reachedafter that, a reversal of refraction occurs, and signal trapped in sound channelcoastal shipping noise can be propagated long distances
33
Homework Assignment 2
assigned: 18 Jan 2010due: 27 Jan 2010
A yellow submarine is conducting a passive search against blue submarines. Yellow submarines have a sonar with directivity index of 15 dB and detection threshold 8 dB. Blue submarines have known source level 140 dB. Environmental conditions yield an isotropic noise level of 65 dB. You can assume an absorption decay coefficient 0.02 dB/km.
At what range can the blue submarine be detected by the yellow submarine? Show your answer graphically.
34
35
Oc679 Acoustical Oceanography