Printed in China
COLOR MONITORSERVICE MANUAL
North/Latin America http://aic.lgservice.comEurope/Africa http://eic.lgservice.comAsia/Oceania http://biz.lgservice.com
CAUTIONBEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS NO. : LM14P
MODEL:
Internal Use Only
29UM55
P/NO : MFL67715298(1406-REV00)
CONTENTS
CONTENTS .............................................................................................. 2
PRECAUTION............................................................................................3
SERVICING PRECAUTIONS.....................................................................4
SPECIFICATIONS......................................................................................6
TIMING CHART .......................................................................................11
ADJUSTMENT .........................................................................................14
BLOCK DIAGRAM...................................................................................18
TROUBLE SHOOTING ............................................................................19
EXPLODED VIEW .................................................................................. 22
SVC. SHEET ...............................................................................................
- 2 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
PRECAUTIONWARNING FOR THE SAFETY-RELATED COMPONENT.
• There are some special components used in LCD monitor thatare important for safety. These parts are marked on theschematic diagram and the Exploded View. It is essentialthat these crit ical parts should be replaced with themanufacturer’s specified parts to prevent electric shock, fire orother hazard.
• Do not modify original design without obtaining writtenpermission from manufacturer or you will void the original partsand labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE WITHBACKLIGHT UNIT.
• Must mount the module using mounting holes arranged in fourcorners.
• Do not press on the panel, edge of the frame strongly or electricshock as this will result in damage to the screen.
• Do not scratch or press on the panel with any sharp objects,such as pencil or pen as this may result in damage to the panel.
• Protect the module from the ESD as it may damage theelectronic circuit (C-MOS).
• Make certain that treatment person’s body are groundedthrough wrist band.
• Do not leave the module in high temperature and in areas ofhigh humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within themodule.
• If the surface of panel become dirty, please wipe it off with asoftmaterial. (Cleaning with a dirty or rough cloth may damagethe panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
• If you want to replace with the new backlight (CCFL) or LIPSpart, must disconnect the AC power because high voltageappears at inverter circuit about 650Vrms.
• Handle with care wires or connectors of the inverter circuit. Ifthe wires are pressed cause short and may burn or take fire.
Leakage Current Hot Check Circuit
CAUTIONPlease use only a plastic screwdriver to protect yourselffrom shock hazard during service operation.
1.5 Kohm/10W
To Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
When 25A is impressed between Earth and 2nd Groundfor 1 second, Resistance must be less than 0.1*Base on Adjustment standard
Ω
0.15uF
- 3 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
SERVICING PRECAUTIONSCAUTION: Before servicing receivers covered by this servicemanual and its supplements and addenda, read and follow theSAFETY PRECAUTIONS on page 3 of this publication.
NOTE: If unforeseen circumstances create conflict between thefollowing servicing precautions and any of the safety precautions onpage 3 of this publication, always follow the safety precautions.Remember: Safety First.
General Servicing Precautions1. Always unplug the receiver AC power cord from the AC power
source before;a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.b. Disconnecting or re-connecting any receiver electrical plug or
other electrical connection.c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.CAUTION: A wrong part substitution or incorrect polarityinstallation of electrolytic capacitors may result in anexplosion hazard.
2. Test high voltage only by measuring it with an appropriate highvoltage meter or other voltage measuring device (DVM,FETVOM, etc) equipped with a suitable high voltage probe.Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of itsassemblies.
4. Unless specified otherwise in this service manual, cleanelectrical contacts only by applying the following mixture to thecontacts with a pipe cleaner, cotton-tipped stick or comparablenon-abrasive applicator; 10% (by volume) Acetone and 90% (byvolume) is opropyl alcohol (90%-99% strength)CAUTION: This is a flammable mixture.Unless specified otherwise in this service manual, lubrication ofcontacts in not required.
5. Do not defeat any plug/socket B+ voltage interlocks with whichreceivers covered by this service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of itselectrical assemblies unless all solid-state device heat sinks arecorrectly installed.
7. Always connect the test receiver ground lead to the receiverchassis ground before connecting the test receiver positivelead.Always remove the test receiver ground lead last.
8. Use with this receiver only the test fixtures specified in thisservice manual.CAUTION: Do not connect the test fixture ground strap to anyheat sink in this receiver.
Electrostatically Sensitive (ES) DevicesSome semiconductor (solid-state) devices can be damaged easilyby static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ESdevices are integrated circuits and some field-effect transistors andsemiconductor "chip" components. The following techniquesshould be used to help reduce the incidence of componentdamage caused by static by static electricity.
1. Immediately before handling any semiconductor component orsemiconductor-equipped assembly, drain off any electrostaticcharge on your body by touching a known earth ground.Alternatively, obtain and wear a commercially availabledischarging wrist strap device, which should be removed toprevent potential shock reasons prior to applying power to theunit under test.
2. After removing an electrical assembly equipped with ESdevices, place the assembly on a conductive surface such asaluminum foil, to prevent electrostatic charge buildup orexposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESdevices.
4. Use only an anti-static type solder removal device. Some solderremoval devices not classified as "anti-static" can generateelectrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generateelectrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protectivepackage until immediately before you are ready to install it.(Most replacement ES devices are packaged with leadselectrically shorted together by conductive foam, aluminum foilor comparable conductive material).
7. Immediately before removing the protective material from theleads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will beinstalled.CAUTION: Be sure no power is applied to the chassis or circuit,and observe all other safety precautions.
8. Minimize bodily motions when handling unpackagedreplacement ES devices. (Otherwise harmless motion such asthe brushing together of your clothes fabric or the lifting of yourfoot from a carpeted floor can generate static electricitysufficient to damage an ES device.)
General Soldering Guidelines1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within therange or 500ºF to 600ºF.
2. Use an appropriate gauge of RMA resin-core solder composedof 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
bristle (0.5 inch, or 1.25cm) brush with a metal handle.Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering techniquea. Allow the soldering iron tip to reach normal temperature.
(500ºF to 600ºF)b. Heat the component lead until the solder melts.c. Quickly draw the melted solder with an anti-static, suction-
type solder removal device or with solder braid.CAUTION: Work quickly to avoid overheating the circuitboard printed foil.
6. Use the following soldering technique.a. Allow the soldering iron tip to reach a normal temperature
(500ºF to 600ºF)b. First, hold the soldering iron tip and solder the strand against
the component lead until the solder melts.c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it thereonly until the solder flows onto and around both thecomponent lead and the foil.CAUTION: Work quickly to avoid overheating the circuitboard printed foil.
d. Closely inspect the solder area and remove any excess orsplashed solder with a small wire-bristle brush.
- 4 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
IC Remove/ReplacementSome chassis circuit boards have slotted holes (oblong) throughwhich the IC leads are inserted and then bent flat against thecircuit foil. When holes are the slotted type, the following techniqueshould be used to remove and replace the IC. When working withboards using the familiar round hole, use the standard techniqueas outlined in paragraphs 5 and 6 above.
Removal1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the soldermelts.
2. Draw away the melted solder with an anti-static suction-typesolder removal device (or with solder braid) before removing theIC.
Replacement1. Carefully insert the replacement IC in the circuit board.2. Carefully bend each IC lead against the circuit foil pad and
solder it.3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete TransistorRemoval/Replacement1. Remove the defective transistor by clipping its leads as close as
possible to the component body.2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.3. Bend into a "U" shape the replacement transistor leads.4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" withlong nose pliers to insure metal to metal contact then soldereach connection.
Power Output, Transistor DeviceRemoval/Replacement1. Heat and remove all solder from around the transistor leads.2. Remove the heat sink mounting screw (if so equipped).3. Carefully remove the transistor from the heat sink of the circuit
board.4. Insert new transistor in the circuit board.5. Solder each transistor lead, and clip off excess lead.6. Replace heat sink.
Diode Removal/Replacement1. Remove defective diode by clipping its leads as close as
possible to diode body.2. Bend the two remaining leads perpendicular y to the circuit
board.3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.4. Securely crimp each connection and solder it.5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and ifnecessary, apply additional solder.
Fuse and Conventional ResistorRemoval/Replacement1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.2. Securely crimp the leads of replacement component around
notch at stake top.3. Solder the connections.
CAUTION: Maintain original spacing between the replacedcomponent and adjacent components and the circuit board toprevent excessive component temperatures.
Circuit Board Foil RepairExcessive heat applied to the copper foil of any printed circuitboard will weaken the adhesive that bonds the foil to the circuitboard causing the foil to separate from or "lift-off" the board. Thefollowing guidelines and procedures should be followed wheneverthis condition is encountered.
At IC ConnectionsTo repair a defective copper pattern at IC connections use thefollowing procedure to install a jumper wire on the copper patternside of the circuit board. (Use this technique only on ICconnections).
1. Carefully remove the damaged copper pattern with a sharpknife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (ifused) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire andcarefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copperpattern and let it overlap the previously scraped end of the goodcopper pattern. Solder the overlapped area and clip off anyexcess jumper wire.
At Other ConnectionsUse the following technique to repair the defective copper patternat connections other than IC Pins. This technique involves theinstallation of a jumper wire on the component side of the circuitboard.
1. Remove the defective copper pattern with a sharp knife.Remove at least 1/4 inch of copper, to ensure that a hazardouscondition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the patternbreak and locate the nearest component that is directlyconnected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of thenearest component on one side of the pattern break to the leadof the nearest component on the other side.Carefully crimp and solder the connections.CAUTION: Be sure the insulated jumper wire is dressed so theit does not touch components or sharp edges.
- 5 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
SPECIFICATIONS1. General Specification
No Item Content Remark 1 Customer BRAND 2 User Model Name 29UM55 3 Sale region Refer to Suffix standard 4 Feature 29” Wide LCD MONITOR 5 Chassis Name LM14P
6
General Scope
External SW &Adj. LEFT, RIGHT, UP, DOWN, CENTER
Function Picture Mode Ratio, ECO(Super Energy Saving), Six Color, Audio Volume(Headphone),
7
Power Cord
Length : 1.55±0.05 M Shape : Wall-out Color : Black Weight : 130g
Refer to Suffix standard and power
cord table
8 Cable
DVI
Length : Shape : Color : Pin :
Do not Support
HDMI
Length : 1.8m Shape : Detachable Type Color : Black Weight : 102g
Support
USB Length : Shape : Color :
Do not Support
Audio Length : Shape : Color:
Do not Support
TV Length : ,Shape : ,Color: ,Pin Do not Support
9 Power
Input: AC100~240V 50~60Hz,1.2A Max Output: DC 19V 2.1A Adapter Weight : 190g
40W
10 Applying module list
P/No Specification EAJ62987701 LM290WW2-SSA1
11 Etc (accessory) Manual CD - Support
- 6 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
3. Optical Character
2. Mechanical specification
No Item Content Remark
1 Product
Dimension
Width (W) Length (D) Height (H) Before Packing 703.0mm 213.2mm 414.2cm With stand
703.0mm 64.0mm 328mm Without stand After Packing 814mm 405mm 156mm
2 Product Weight
Only SET 5.2kg Without stand : 4.7kg With BOX 7.5Kg
3 Container Loading Quantity
Individual (Vertical Type)
20ft 40ft Face_up 40ftH/C - Indi. : 1,296 - Pallet : 1,152
Indi. Pallet Indi. Wood
en 525 462 1,080 966
4 Stand Assy
Type Base detachable Size (W x D x H) 124mm x 213.2mm x 42.6mm Only stand ass’y Tilt Degree -5°(+/-3°)~ +20°(+/-3°)
Tilt force F1 /F2 :1.0 ~ 1.5kgf Folding Degree9 None
5 Appearance General Refer to Standard of LG(56)G2-1011
No Item Criteria Remark
1 Viewing Angle <CR≥10>
Horizontal(R/L) : +89º/-89º ( (Typ.)
Vertical(Top/Bottom) : +89º/-89º (Typ.)
2 Luminance(휘도) Average Luminance (cd/m2)
200(min), 250 (Typ.) (Full white pattern, 0.7V)
Warm (6500K)
Average Luminance (cd/m2)
170(min) (Full white pattern, 0.7V)
Medium (8000K)
Average Luminance (cd/m2)
150(min) (Full white pattern, 0.7V)
Cool (9300K)
Super Energy Saving On
Max 25% down from S-Energy Saving Off.
Luminance Uniformity
75%(min),
3 Contrast Ratio(명암 비) 700(MIN), 1000(TYP), DFC->5,000,000:1(Typ.) / 4,000,000:1(Min) (It is measured at center point)
4 Response Time On/off:14ms(TYP, GTG),
5 CIE Color
Coordinates (색 좌표)
Minimum Normal Maximum
White WX
Typ-0.03 0.313
Typ+0.03 Warm
(6500K) WY 0.329 White WX Typ-0.03 0.295 Typ+0.03 Medium
WY 0.305 (8000K)
White WX
Typ-0.03 0.283
Typ+0.03 Cool
(9300K) WY 0.298
RED RX
Typ-0.03
0.660
Typ+0.03 Warm
(6500K)
RY 0.331
GREEN GX 0.306 GY 0.609
BLUE BX 0.149
BY 0.062
- 7 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
4. Engineering Specification
1 Supported Sync. Type Separate Sync.
2 Operating Frequency HDMI Horizontal 30 ∼ 90kHz
Vertical
(AV)25~60 Hz, (PC)50~75 Hz
DP Horizontal 30 ∼ 90kHz
Vertical 50 ~ 75 Hz
3 Resolution HDMI Max. 2560×1080 @ 60Hz Recommend 2560×1080 @ 60Hz
DP Max. 2560×1080 @ 60Hz Recommend 2560×1080 @ 60Hz
4 Input Voltage Voltage :100 – 240 Vac, 50 or 60Hz, 1.0A
5 Inrush Current Cold Start : 50 A Hot : 120 A 6
Operating Condition Sync (H/V) Video LED Wattage
On Mode
On/On Active White 34W(Typ) Test condition 1.2560x1080@60Hz 2. burst pattern 3. 100~240V 4. After aging 30min On/On Active White 39W(Max)
EPA6.0 On/On Active White EPA spec
31.69 W
Adjust brightness controls until the luminance of the screen is 200(cd/m2).
Sleep Mode Off/On On/Off Off/Off
Off White Blinking < 0.5W
Off Mode (Power switch off) - - Off < 0.5W
ECO High, Low,Off
Low High White
Efficiency 15±5% (3W/h) 25±5% (5W/h)
-Test Condition (1)
7
MTBF 30,000 HRS with 90% Confidence level
Lamp Life : 30,000 Hours(Min)
8
Using Altitude 5,000 m (for Reliability) 3,000m(for FOS)
9
Environment
Condition
0perating
Temperature 10 °C ~ 35 °C Humidity 10% ~ 80%
Storage Temperature -20 °C ~ 60 °C Humidity 5% ~ 90% non-condensing
OSD MENU Brightness 1 - 100
- 8 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
MENU
(Monitor block)
Contrast 1 – 100
Volume 1 – 100, Mute
Input HDMI1 / HDMI2/ DP
Ratio Wide / Cinema1 /
Cinema2 / Original / 1:1
Func.
ECO High, Low, Off
Reader mode Reader1, Reader2,
Reader Off
Picture Mode Custom, Photo, Cinema, Game
PBP PBP
PBP On, Off
Input
Main: HDMI1, HDMI2, DP
Sub: HDMI1, HDMI2, DP
Audio HDMI1, HDMI2, DP
Swap On, Off
Sub Full On, Off
Ratio Main Wide, Original
Ratio Sub Wide, Original
Picture
Sharpness 0 - 10
Black Level Low, High
(BLACK LEVEL enable at HDMI input)
Response Time
High, Middle, Low
Color
Gamma Gamma0, Gamma1,
Gamma2
16 Language: English, Germanic, French, Spanish, Italian, Swedish, Finnish, Portuguese Brazilian Portuguese, Polish, Russian, Greek, Chinese, Japanese, Korean,
Color Temp Warm, Medium, Cool,
Custom Red 0 - 100
Green 0 – 100 Blue 0 – 100
Six Color (Hue,
Saturation) 0 - 100
Language PC/AV Mode N/A Main Audio HDMI1/HDMI2,DP
Button Sound N/A Power LED On / Off
DP 1.2 On / Off OSD Lock On / Off
Reset Reset/Cancel
MENU (AV/TV block)
CHANNEL
CHANNEL 2~69(AIR) / 1 ~ 125(CABLE)
Function Support: No
ADD/DEL CH ADD/DELETE
AUTO CHANNEL ON/OFF SELECT AIR/CABLE FINE TUNE 0 ~ 100
ADJUSTMENT
CONTRAST 0~100
Function Support: No
BRIGHTNESS
0~100
SHARPNESS 0~100 COLOR 0~100 TINT 0~100
AUDIO
VOLUME 0~100
Function Support: No
BASS N/A TREBLE N/A MUTE ON/OFF SOUND MONO/STEREO
SETUP
LANGUAGE▶ English/German/French/Esperanto Italian/Korean…
Function Support: No
IMAGE SIZE ▶ FULL/1:1
OSD POSITION TRANSPARENCY
0~100
- 9 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
5.1 Display Area
A
1) Active Display Area of the LCD Monitor Should be within Cabinet’s Bezel.2) Distance Difference between Active Area and Bezel
| A-B|<1.0 mm , | C-D|<1.0 mmA: The Distance from The Left of Active Area to the Bezel B: The Distance from The Right of Active Area to the BezelC: The Distance from The Top of Active Area to the Bezel D: The Distance from The Bottom of Active Area to the Bezel
C
Active area
A A B
Bezel
D
5. Applying module Character
No Item Content Remark
1 LCD Module Feature
Maker LGD
Type IPS Active Display Area 29 inches(73.025cm) diagonal (21:9) Pixel Pitch [mm] 0.2 0.0876(H)mm x RGB x 0.2628(V)mm Electrical Interface 2ch-LVDS(41P), 2ch-LVDS(51P)
Color Depth 6-bit + A-FRC, 16.7M colors Size (Outline) [mm] 602.2(H) x 271.1(V) x16.5(D) (Typ.)
mm(Typ.) Surface Treatment Hard coating (3H) & Anti-Glare treatment
of the front polarizer Operating Mode Transmissive mode, normally Black
Back light Unit White LED
R/T Typical 14ms Max. 28ms
Standard Measurement Condition
n Ambient Luminance Level : dark ( < 10 lux)
n Ambient Temperature : Normal Temperature(10 ~ 25 ℃)
n warm-up Time : More than 30min (at Full White Pattern)
n Input Signal : 2560X1080@60Hz
n Contrast : 70
n Brightness : Max. 100
n 6500K : Color Temperature Setting is 6500 K( if it’s not special specification)
n Clock/Clock Phase : The Best Setting
l Another Spec.: Product Specification Standard( LG(55)G1-1034 )
l Cosmetic Spec. : LCD Module IIS Spec.
- 10 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
6. EDID6.1
29UM55
No Item Content 16진 Data 1 Manufacturer ID GSM 1E 6D
2 Product ID (HDMI) (Display Port)
23025(F1 59) 23026(F2 59)
3 Year 2014 4 Version 1 01
5 Revision HDMI : 3
DP : 4 03 04
6 Serial Number * * 7 Week ** ** 8 Model Name LG ULTRAWIDE -- 9 Check Sum **** ****
10 Special Item Need to Input Serial Number
** Protocol : DDC 2AB
Data ( 128 Bytes ) à29UM55
EDID Ver. 1.3 FOR HDMI 1 (256Byte)
- 11 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
EDID Ver. 1.3 FOR HDMI 2 (256Byte)
EDID Ver. 1.4 FOR Display Port (256Byte)
- 12 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
- 13 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
TIMING CHART(1) Signal(Video & Sync)
V i d e o
BC
S y n c
D E F
A
(2) HDMI/DP
mode section polarity
DOT CLOCK [MHz]
Frequency [kHz]/[Hz]
Total Period(E)
Display (A)
Front Porch (D)
Sync. (C)
Back Porch (B)
Resolution
1 H(Pixels) -
28.321 31.468 900 720 18 108 54
720 X 400 V(Lines) + 70.08 449 400 12 2 35
2 H(Pixels) -
25.175 31.469 800 640 16 96 48
640 x 480 V(Lines) - 59.94 525 480 10 2 33
3 H(Pixels) -
31.5 37.5 840 640 16 64 120
640 x 480 V(Lines) - 75 500 480 1 3 16
4 H(Pixels) +
40.0 37.879 1056 800 40 128 88
800 x 600 V(Lines) + 60.317 628 600 1 4 23
5 H(Pixels) +
49.5 46.875 1056 800 16 80 160
800 x 600 V(Lines) + 75.0 625 600 1 3 21
6 H(Pixels) -
65.0 48.363 1344 1024 24 136 160
1024 x 768 V(Lines) - 60.0 806 768 3 6 29
7 H(Pixels) +
78.75 60.123 1312 1024 16 96 176
1024 x 768 V(Lines) + 75.029 800 768 1 3 28
8 H(Pixels) +
108 67.5 1600 1152 64 128 256
1152 x 864 V(Lines) + 75 900 864 1 3 32
9 H(Pixels) +
74.25 45 1650 1280 110 40 220
1280x720 V(Lines) + 60 750 720 5 5 20
10 H(Pixels) +
108 63.981 1688 1280 48 112 248 1280 x
1024 V(Lines) + 60.02 1066 1024 1 3 38
11 H(Pixels) +
135 79.976 1688 1280 16 144 248 1280 x
1024 V(Lines) + 75.025 1066 1024 1 3 38
12 H(Pixels) +
108.0 60.00 1800 1600 24 80 96
1600 x 900 V(Lines) + 60.00 1000 900 1 3 96
13 H(Pixels) -
146.25 65.29 2240 1680 104 176 280 1680 x
1050 V(Lines) + 59.954 1089 1050 3 6 30
14 H(Pixels) +
148.50 67.50 2200 1920 88 44 148 1920 x
1080 V(Lines) - 60 1125 1080 4 5 36
15 H(Pixels) -
185.58 66.7 2784 2560 64 64 96 2560 x
1080 V(Lines) + 60 1111 1080 3 10 18
l DVI : DTV Mode is not supported (interlace mode)
H/V Timing
input
Factory support mode
Horizontal frequency
Vertical frequency
(Preset Mode) (KHz) (Hz) 1 480P 31.5 60 2 576P 31.25 50 3 720P 37.5 50 4 720P 45 60 5 1080P 56.25 50 6 1080P 67.5 60
(3) HDMI Video
- 14 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
ADJUSTMENT
1. CoverageApply to 73.025 cm Wide monitor made in Monitor FactoryGumi Korea) or made in accordance with the standard of GumiFactory process.
2. Appointment
2.1 Adjustment must be done as fixed sequence, and adjustmentsequence can be modified after agreement withthe responsibleR&D engineer considering mass-production condition.
2.2 Power : AC 100 - 240 Voltage (Free)2.3 Input signal:
2.3.1 RGB Input: As Product Standard (Signal ROM : LB800KVer1.6)
2.3.2 RJ-45 input : As Product Standard (Ethernet connectionthrough network from Host PC)
* PC spec for MK(Minikey) Loader (TBD): CPU - Dual core 2.0GHzD, Memory - 2 GByteD
*PC spec for Host PC (TBD): CPU - Dual core 2.0 GHzD,Memory - 2 GByteD
2.4 Warm-up Time: Over than 30 minutes2.5 Adjustment equipment : White balance equipment (CA-110),
Display adjust equipment, VG-813(or VG819), Oscilloscope,PC (More than 486 computer ) & White balance adjustprogram.
3. Adjustment
3.1 OverviewUse factory automation equipment and adjust automaticmovement. But, do via passivity adjust in erroroccurrence.
3.2 Adjustment order(refer to the Adjustment standard and adjustment command table)
3.2.1 Board Assembly Line3.2.1.1 15pin D-sub (RGB)· Connect input signal to 15pin D-sub.· Check the firmware version & model name. And write the
firmware code to the serial Flash ROM by ISP.· Ready for adjustment : check whether adjustment command
works normally or not and the operating state of each mode. · Check the display state of gray color when 256 gray scale
patterns is embodied.· Read by EEPROM Read Command to check whether initial
value is correct or not.3.2.1.2 MK( Minikey ) Loading· Open MK Loader Tool on MK Loader PC.( * MK Loader PC should be connected Internet) · Connect input signal to RJ-45 input with LAN cable connected
network devices such as routers.· Turn on the Monitor set. · Click the box when the °∞empty port °∞box is changed to “write
mini-key” in MK Loader Tool.
3.2.1.2 RJ-45 input · Connect input signal to RJ-45 input with LAN cable connected
network devices such as routers.· Check USB 1.1 Port (Keyboard/ Mouse) : @RJ-45 input · Check USB 2.0 Port (USB Memory Stick 2port) : @RJ-45 input · Check Audio (Ear-phone out/ Mic in/ Speaker) : @RJ-45 input,
PC audio volume : MAX* LAN cable * Router * PC: vSpace S/W for N+ ( Ver 4.5.xx.xx ) --- Caution: Ver
4.4.xx.xx for N1742L family
3.2.2 Total Assembly Line· Ready : Heat-run during5 minutes in the state with signal· Connect input signal to D-sub.· Default value before adjustment : Contrast “70” , Brightness
‘100(Max)”
3.2.3 Adjustment of Horizontal/Verticality screenposition, Clock and Clock Phase at each Mode.
· There is no special factory mode adjustment. Writing initial valueof EEPROM in Board Assembly line is adjusting Preset Modeand Reset mode. (EEPROM is initialized when AC Power isON first.)
· If the change of FOS data is needed after M.P, it is possible bywriting Mode Data with EEPROM write command or modifyingthe Mode Data in MICOM itself.
3.2.4 Color coordinates adjustment and Luminanceadjustment.
3.2.4.1 Color coordinates adjustment· Monitor Contrast / Brightness
- Contrast : 70- Brightness : 100(Max)
· CA-110: Set “channel 9”· Signal Generator : At cut-off and drive --> 16 step pattern for
ADC (Program No.: 31)- Output Voltage : 700 mVp-p - Output Mode : Mode 12 (SXGA 60 Hz)mode Setting.
3.2.4.2.Adjustment : Board Assembly Line· Select RGB mode· Input 16 step pattern for ADC (Program No.31 (Mode 12,Pattern
11)). (Video level : 700 mVp-p)· Adjust by commanding AUTO_COLOR_ADJUST· Confirm “Success” message in Screen or Check the data of
0xFE, 0xFF address of EEPROM(0XA6) is 0xAA after waiting 5seconds.
· If there is “FAULT” message or the data of 0xFE, 0XFF addressof EEPROM(0xA6) is not 0xAA, do adjust again.
· If all Adjustment is completed, the values of 6500K, User Colorand 9300K are saved automatically.
· Select RGB mode· Input 16 step pattern for ADC (Program No.31 (Mode 12,Pattern
11)). (Video level : 700mVp-p)· Adjust by commanding AUTO_COLOR_ADJUST· Confirm “Success” message in Screen or Check the data of
0xFE,0xFF address of EEPROM(0xA6) is 0xAA after waiting 5seconds.
3.2.4.3. Confirm at Total Assembly Line: adjustment· Check the data of 0xFE, 0xFF address of EEPROM(0xA6) is
0xAA.· If the data of 0XFE, FF address of EEPROM(0xA6) is not
0xAA, do adjust again by 3.2.4.2.
- 15 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
3.2.4.4. Confirm PRESET 6500K Color coordinates and AdjustPRESET 9300K Color coordinates .
· Set as Aging mode ON, by commanding AGING_ON/OFFcommand code.
· Select Module that is being used in present production bycommanding MODULE SELECT. ( It is not needed so far.However, it will be needed to apply other modules)
· Send SYSTEM RESET command to set Module data. · Input Full White Pattern (Video level : 700 mVp-p) · Set as 9300K by commanding COLOR_MODE_CHANGE
Command code.· Check to meet x = 0.283 ± 0.03, y=0.298 ± 0.03, and confirm.· Only if it does not meet, adjust as below steps.· Adjust to meet x = 0.283 ± 0.01, y=0.298 ± 0.01 in 5 minutes. and
confirm.· Save 9300K Color by commanding COLOR SAVE Command
code.· Set as 6500K by commanding COLOR_MODE_CHANGE
Command code.· Check to meet x = 0.313 ± 0.03, y=0.329 ± 0.03, and confirm.· Only if it does not meet, adjust as below steps.· Adjust to meet x = 0.313 ± 0.01, y =0.329 ± 0.01, and confirm.· Save 6500K Color by commanding COLOR SAVE Command
code.· Set as sRGB by commanding COLOR_MODE_CHANGE
Command code.· Adjust to meet Y = 150 ± 50, and confirm.· Save sRGB Color by commanding COLOR SAVE Command
code.3.2.4.5. Confirm User color coordinates .· Confirm Whether User color is saved same as 6500K.· After confirming Color coordinates, Must return to 6500K
3.2.5 Confirm Operation state.3.2.5.1 Operation mode : Confirm whether each appointed mode
operate correctly or not.3.2.5.2 Confirmation of Adjustment condition and operation :
Confirm whether it meet Auto/Manual equipment Adjustmentstandard or not.
· Confirm Analog screen state : Confirm screen state at belowmode.
Appointment mode (RGB input): 640*480 @60Hz (Mode 1), 800*600@75Hz(Mode 5),1024*768@60Hz(Mode 8), 1280*1024@60Hz(Mode 12),
SMPTE pattern(Check 0%,5%,95%,100%)–Mode can be added.
3.2.5.3. Confirm Auto adjustment operation.· Input Analog 1 Dot on/off & Rectangle Pattern at Mode
12(1280x1024@60 Hz)· Confirm adjustment operation by changing Clock, Phase, H/V
Position.· Check Clock, Phase by pressing AUTO Key.· Confirm first set of new lot by periods
3.2.5.4 Other quality· Confirm that each items satisfy under standard condition that was
written product spec.· Confirm Applying Module & MICOM Setting --> Confirm with
Service OSD - Confirm at Service OSD by “Menu + Power key” on .(fromPower off) - Confirm first set of new lot by periods, and confirm periodically
when there is Process change or Adjustment setting change.
3.2.5.5. OSD & Adjustment device Confirmation : Confirmoperation mentioned as product spec.
· Vary Brightness and Contrast and confirm the variation ofLuminance and display status.
· Operate the f-engine function and confirm variation of Luminance.· Make sure to do FACTORY RESET after confirmation of OSD
function.
3.2.5.6. Confirm the display state by inputting 8 color Bar Pattern &256 Gray Scale pattern.
3.2.5.7. DPM operation confirmation : Check if Power LED Colorand Power Consumption operates as standard.
· Measurement Condition : 230 V@ 50 Hz (Analog)· Confirm DPM operation at the state of screen without Video
Signal.
3.2.5.8. RJ-45 input· Connect input signal to RJ-45 input with LAN cable connected
network devices such as routers.· Check USB 1.1 Port (Keyboard/ Mouse) : @RJ-45 input · Check USB 2.0 Port (USB Memory Stick 2port) : @RJ-45 input · Check Audio (Ear-phone out/Mic in/Speaker) : @RJ-45 input, PC
audio volume : MAX* LAN cable * Router * PC: vSpace S/W for N+ ( Ver 4.5.xx.xx ) --- Caution: Ver
4.4.xx.xx for N1742L family
3.2.5.9. DDC EDID Write( Set as Aging mode ON, by commanding AGING_ON/OFFcommand code. )
1) SUFFIX: xxxxxPN· Connect analog Signal Cable to D-sub wafer.· Write EDID DATA to EEPROM(24C08) by using DDC2AB
protocol.· Check whether written EDID data is correct or not.
(refer to Product spec). --> After writing EDID, send Elapsed Time Clear command.(Elapsed time should not be displayed, after EDID writing): Confirm periodically (in the first set of new lot, process change)
whether module name and aging time disappeared on the self-diagnostics OSD with signal cable disconnected.
--> If Elapsed Time Clear command isn°Øt executed, modulename, aging time and TCO word appear on the self-diagnosticsOSD.(Module name and aging time should not appear afterwriting EDID)
--> Make sure to do FACTORY RESET at the final process.
3.2.5.10. Shipping condition· Contrast : 70· Power Switch : Off· Brightness : “100(Max)” · Color Select : Preset ( 6500K )· Language Select : Refer to product spec.· OSD Position : Center· Power indicator : ON· Flatron f-engine : Normal
- 16 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
4.Standard of Auto/Manual equipment adjustment
No Category Class(Type) Rule Remark
1
Safety UL UL60950-1 YES
CSA (cUL) CSA C22.2 No.60950-1-03 YES
TUV-GS(TUV-Type) EN60950-1 TUV-Type SEMKO EN60950-1 No
2 EMC FCC CLASS B FCC 47 CFR Part 15 Class B YES
CE EN55022B, EN55024, EN61000-3-2, 3 YES
3 X-Ray (CRT only)
DHHS DHHS Rule 21 CFR Subchapter J N/A
HWC HWC Radiation Emitting Device ACT N/A
4 Low Radiation
MPR II MPR 1990:8; MPR 1990::01 NO
5 TCO TCO6.0 Emission, Ergonomics, Ecology, Energy saving
YES
6 Ergonomics ISO9241 (CRT) ISO9241-3, 7, 8 NO
ISO13406-2 (LCD) ISO13406-2,ISO9241-307 NO
7
Etc (Korea)
KC(SAFETY) Electric Supplies Safety Rule (K60950) NO
KC(EMC) MIC Ordinance 825 MIC Notice 100,Class B, Electric Article Technical Standard Ⅲ
NO
8 Etc (China)
CCC GB4943, GB9254, GB17625.1 YES
9 Test Hi-Pot 1500 V ac or 2121Vdc, 1 sec, under 10mA No
Earth Continuity 25 A, 1 sec, under 0.1 ohm No
10 EPA 6.0 Energy Star 6.0 Energy Star Display Version 6.0 YES
11 EPEAT Gold Yes
Note
#3 - CRT monitor only
#4 – Different from Models
#5 – Different from Models
#6 - ISO9241-3, 7, 8 - CRT monitor only
ICO13406-2 / ISO 9241-307 - LCD monitor only
#7 –Safety Certification(안전인증) – Different from Models
* – Update to new standard regulation and Revision 3.0
- 17 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
5. Pattern for Adjustment
Pattern 0 : FULL BLACK (State of without video signal )Pattern 1 : FULL WHITE (Don’t display other Character except for White Pattern)Pattern 3 : FULL WHITEPattern 4 : Cross hatch pattern (Horizontal 10Line, Vertcial 8Line) & Rectangle PatternPattern 5 : 1 Dot on, 1 Dot off & Rectangle PatternPattern 6 : Vertical Sync only input (Use signal cable of which Pin #5 is GND)Pattern 7 : Horizontal Sync only input (Use signal cable of which Pin #5 is GND)Pattern 8 : State of without Vertical/Horizontal Sync and Video Signal. (Use signal cable of which Pin #5 is GND)Pattern 9 : 8 Color Bar Pattern + 16 Gray Level PatternPattern 10 : SMPTE PatternPattern 11 : 16 Gray Step Pattern (700mV)
- 18 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
BLOCK DIAGRAM (Main)
NT6
8370
(E-v
ersion)
Hea
dpho
neH
eadp
honeA_o
ut_R
A-o
ut_L
SPI_
CLK
SPI_
DI
SPI_
CSN
SPI_
DO
SPI_
WP
Pane
l (25
60x1
080)
WLE
D_E
NABLE
WLE
D P
DIM
WLE
D_A
DIM
LVD
S41
p
HD
MI 1
HD
MI 1
DP
DP
DPR
X_A
UXP
DPR
XAU
XN
HD
MI 2
HD
MI 2
Key
1, K
ey2
DD
R2
SDRAM
(1GB)
DD
R2
SDRAM
(1GB)
DD
R2
Dat
a[0:
15]
DD
R2
Addre
ss[0
:12]
DD
R2
Dat
a[0:
15]
DD
R2
Addre
ss[0
:12]
LED
Drive
r IC
LED
Drive
r IC
DT1
631S
DT1
631S
Flas
hFl
ash
Mem
ory
Mem
ory
(2M
)(2
M)
LVD
S51
p
TMD
S
Joys
tick
(Cont
rol K
ey)
TMD
S
EEPR
OM
EEPR
OM
- 19 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
TROUBLESHOOTING GUIDE1. NO POWER
`
No p
ower
iss
ue
Che
ck J
K50
0 P
IN4(
19V
)
Is IC
500
PIN
2(19
V),P
IN3(
10V
),IC
509
PIN
2(19
V),P
IN3(
3.3V
),IC
510
PIN
2(19
V),P
IN3(
5V)
CH
ECK
AD
AP
TER
CH
ECK
IC
500
or IC
509
or
IC51
0
Is IC
505,
PIN
2(1.
3V)
IC50
6 P
IN2(
1.9V
)C
HEC
K I
C50
5 or
IC50
6
Is IC
100
PIN
N1,
PIN
N2
PU
LSE
CH
ECK
CR
YSTA
L X
200
YES
YES
YES
NO NO NO NO
CH
ECK
IC10
0
IC51
0-#2
IC51
0-#3
IC50
9#3
X200
- 20 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
2. NO RASTER (OSD IS NOT DISPLAYED) – MAINN
o Ra
ster
(OSD
is n
ot d
ispla
yed)
Che
ck IC
100
PIN
B
19(3
.3V
)
IC10
0 P
IN N
1,N
2 12
MH
z
CH
ECK
IC
509
PIN
3(3.
3V)
1.C
HEC
K X
200
2. T
roub
le in
IC10
0
Is IC
100
PIN
C14
C
LK
YES
YES
NO NO NO
Trou
ble
in ca
ble
or LC
D m
odul
e
CHEC
K C
ON
NEC
TIO
N F
rom
HDM
I TO
IC
100
- 21 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
3. TROUBLE IN DPM
CHEC
K HD
MI C
LK
Trou
ble
in D
PM
IC10
0 P
IN H
4
CHEC
K P
C. P
C is
goin
g to
the
DPM
m
ode
YES
YES
NO NO
Trou
ble
in I
C100
Chec
k R1
33 A
ND
R196
- 22 -Copyright © 2010 LG Electronics. Inc. All right reserved.Only for training and service purposes
LGE Internal Use Only
400 90
0
200
520
300
910
700
560
710
610
LV2
LV1
540
920
EXPLODED VIEW
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
THE
S
YMBO
L MA
RK O
F TH
IS S
CHEM
ETIC
DIA
GRAM
INC
ORPO
RATE
SSP
ECIA
L FE
ATUR
ES I
MPOR
TANT
FOR
PRO
TECT
ION
FROM
X-R
ADIA
TION
.FI
RE A
ND E
LECT
RICA
L SH
OCK
HAZA
RDS,
WHE
N SE
RVIC
ING
IF I
S ES
SENT
IAL
THAT
ONL
Y MA
NUFA
CTUR
ES S
PECI
FIED
PAR
TS B
E US
ED F
ORTH
E CR
ITIC
AL C
OMPO
NENT
S IN
THE
SYMB
OL M
ARK
OF T
HE S
CHEM
ETIC
.
HDMI2_SCL-1
HDMI2_SDA-1
HDMI1_RXC+
HDMI2_SCL
+5V
C116
68pF
50V
OPT
R108
10K
HDMI1_SCL
D120
IP4283CZ10-TBA
OPT
3 GND_1
2 TMDS_CH1+
4 TMDS_CH2-
1 TMDS_CH1-
5 TMDS_CH2+
6NC_1
7NC_2
8GND_2
9NC_3
10
NC_4
C101
0.1uF
16V
HDMI2_RX0-
HDMI1_DET
R125
33
R154
0 OPT
HDMI2_RX1+
R162
100K
R159
100K
HDMI1_RX0+
DP_AUXN
EDID_WP
DP_RX1P
R153
10K
DP_HPD
R124
33
+3.3V
C110
68pF
50V
OPT
R126
10K
R127
10K
HDMI2_RXC-
R128
10K
OPT
+3.3V
HDMI1_RXC+
HDMI1_RX1+
+3.3V
DP_AUXN
R144
33
DP_DET
IC103
M24C02-RMN6T
3E2
2E1
4VSS
1E0
5SDA
6SCL
7WC
8VCC
IC101
M24C02-RMN6T
3E2
2E1
4VSS
1E0
5SDA
6SCL
7WC
8VCC
DP_RX2N
HDMI2_RX1-
HDMI1_RX0-
R111
1K
DP_RX0N
HDMI2_SCL
D127
BAT54C A2
C
A1
HDMI2_RX2+
HDMI1_RX1+
R109
100K
OPT
DP_RX3N
HDMI1_RX0-
D112
BAT54C A2
C
A1
R157
10K
JP107
HDMI_5V
R110
1M
DP_RX2P
R117
33
JP106
R160
100K
HDMI2_SDA
R143
33
D121
IP4283CZ10-TBA
OPT
3 GND_1
2 TMDS_CH1+
4 TMDS_CH2-
1 TMDS_CH1-
5 TMDS_CH2+
6NC_1
7NC_2
8GND_2
9NC_3
10
NC_4
C102
0.1uF
16V
R150
10K
OPT
R161
100K
C115
0.1uF
16V
DP_RX3P
DP_RX2N
R10510K
HDMI2_DET
R163
100K
+5V
DP_AUXP
D116
IP4283CZ10-TBA
OPT
3 GND_1
2 TMDS_CH1+
4 TMDS_CH2-
1 TMDS_CH1-
5 TMDS_CH2+
6NC_1
7NC_2
8GND_2
9NC_3
10
NC_4
R113
1M
D119
IP4283CZ10-TBA
OPT
3 GND_1
2 TMDS_CH1+
4 TMDS_CH2-
1 TMDS_CH1-
5 TMDS_CH2+
6NC_1
7NC_2
8GND_2
9NC_3
10
NC_4
EDID_WP
D123
IP4283CZ10-TBA
OPT
3 GND_1
2TMDS_CH1+
4TMDS_CH2-
1TMDS_CH1-
5TMDS_CH2+
6NC_17
NC_28
GND_29
NC_310
NC_4
DP_RX0P
C117
68pF
50V
OPT
R107
1K
R146
10K
R155
10K
R112
10K
DP_RX0N
DP_RX1N
C105
0.1uF16V
D125
BAT54C A2
C
A1
C104
0.1uF16V
JK100
62L020S-34A1N-7T0201-HF_
14
135
12
112
19
18
1041
17983
1676
15
20
21
HDMI2_HPD
DP_RX1P
HDMI1_RX2+
HDMI1_RX1-
HDMI1_RX2-
HDMI1_RX0+
DP_DET
DP_RX2P
C109
68pF
50V
OPT
HDMI1_RX2+
R101
0
JK102
51V019S-35SN-CR2-B-LG
14
NC
13
CEC
5DATA1_SHIELD
20
SHIELD
12
CLK-
11
CLK_SHIELD
2DATA2_SHIELD
19
HPD
18
+5V_POWER
10
CLK+
4DATA1+
1DATA2+
17
DDC/CEC_GND
9DATA0-
8DATA0_SHIELD
3DATA2-
16
SDA
7DATA0+
6DATA1-
15
SCL
+3.3V
R100
0
R164
100K
DP_HPD
D122
IP4283CZ10-TBA
OPT
3 GND_1
2 TMDS_CH1+
4 TMDS_CH2-
1 TMDS_CH1-
5 TMDS_CH2+
6NC_1
7NC_2
8GND_2
9NC_3
10
NC_4
HDMI1_RX2-
DP_RX3N
HDMI1_SDA
JK101
51V019S-35SN-CR2-B-LG
25UM65/29UB65
14
NC
13
CEC
5DATA1_SHIELD
20
SHIELD
12
CLK-
11
CLK_SHIELD
2DATA2_SHIELD
19
HPD
18
+5V_POWER
10
CLK+
4DATA1+
1DATA2+
17
DDC/CEC_GND
9DATA0-
8DATA0_SHIELD
3DATA2-
16
SDA
7DATA0+
6DATA1-
15
SCL
DP_HPD
HDMI_5V
DP_RX1N
DP_AUXN
DP_RX3P
R158
100K
HDMI1_RXC-
DP_RX0P
DP_DET
D115
IP4283CZ10-TBA
OPT
3 GND_1
2 TMDS_CH1+
4 TMDS_CH2-
1 TMDS_CH1-
5 TMDS_CH2+
6NC_1
7NC_2
8GND_2
9NC_3
10
NC_4
HDMI2_RX2-
HDMI2_RX0+
C107
0.1uF
16V
+3.3V
HDMI2_RXC+
HDMI1_RX1-
HDMI1_SDA
R118
33
DP_AUXP
DP_PLUG
+3.3V
D109
BAT54C A2
C
A1
HDMI1_RXC-
HDMI2_SDA
DP_AUXP
R147
10K
R165
100K
HDMI1_SCL
C127
1uF
R170
0
C128
0.1uF
16V
HDMI_5V HDMI2_HPD
HDMI2_SCL
R192
1K
R195
10K
+3.3V
HDMI2_DET
HDMI2_SDA
R19110K
R171
0
R172
0
R173
0
R174
0
R175
0
R176
0
R177
0
R167
0
R169
0
R189
0
HDMI2_RXC-
HDMI2_RX2-
HDMI2_RXC+
HDMI2_RX0+
R184
0
HDMI2_RX1+
HDMI2_RX1-
R188
0
R185
0
R187
0
R183
0
HDMI2_RX0-
R190
0
R186
0
HDMI2_RX2+
R149
0R179
0
R180
0
R182
0
HDMI_5V
HDMI1_HPD
R133
10K
R129
1K
C111
0.1uF
16V
R11410K
R132
33
R178
33
R140
33
HDMI_5V
DP_AUXN
DP_AUXP
JK104
51U019S-3441N-6RLGM5-HF
29UM65/34UM65
14
RESERVED
13
CEC
5TMDS_DATA1_SHIELD
20
BODY_SHIELD
12
TMDS_CLK-
11
TMDS_CLK_SHIELD
2TMDS_DATA2_SHIELD
19
HOT_PLUG_DETECT
18
VDD[+5V]
10
TMDS_CLK+
4TMDS_DATA1+
1TMDS_DATA2+
17
DDC/CEC_GND
9TMDS_DATA0-
8TMDS_DATA0_SHIELD
3TMDS_DATA2-
16
SDA
7TMDS_DATA0+
6TMDS_DATA1-
15
SCL
HDMI1_RX2-
HDMI1_RXC-
HDMI1_RX1-
HDMI1_RX0-
HDMI1_RX2+
HDMI1_RX1+
HDMI1_RX0+
HDMI1_RXC+
HDMI1_RXC-
HDMI1_RXC+
HDMI1_RX0-
HDMI1_RX0+
HDMI1_RX1-
HDMI1_RX1+
HDMI1_RX2-
HDMI1_RX2+
C126
1uF
C125
1uF
C124
1uF
C122
1uF
C121
1uF
C119
1uF
C118
1uF
DP_RX0P
DP_RX0N
DP_RX1N
DP_RX1P
DP_RX2N
DP_RX2P
DP_RX3N
DP_RX3P
HDMI2_RX0+
HDMI2_RX2+
HDMI2_RX1-
HDMI2_RX2-
HDMI2_RXC+
HDMI2_RX1+
HDMI2_RX0-
HDMI2_RXC-
HDMI2_RX0+
HDMI2_RXC+
HDMI2_RXC+
HDMI2_RXC-
HDMI2_RX0-
HDMI2_RX0-
HDMI2_RX0+
HDMI2_RXC-
HDMI2_RX1-
HDMI2_RX2+
HDMI2_RX1+
HDMI2_RX2-
HDMI2_RX2+
HDMI2_RX1-
HDMI2_RX2-
HDMI2_RX1+
DP_RX1N
DP_RX1N
DP_RX1P
DP_RX0P
DP_RX0N
DP_RX1P
DP_RX0P
DP_RX0N
DP_RX2P
DP_RX2N
DP_RX3N
DP_RX3P
DP_RX3N
DP_RX3P
DP_RX2P
DP_RX2N
R168
1K
R181
1K
R196
1K
D102OPT
D103
D108OPT
D110
D111
D117OPT
D126
D129
IC100
NT68370(D VER.)
RX1CB
D1
RX1C
D2
RX10B
E1
RX10
E2
RX11B
F1
RX11
F2
RX12B
G1
RX12
G2
RX2CB
J1
RX2C
J2
RX20B
K1
RX20
K2
RX21B
L1
RX21
L2
RX22B
M1
RX22
M2
RXAUX1N
C1
RXAUX1
C2
RXAUX2N
H1
RXAUX2
H2
BIN1+
P2
BIN1-
P1
SOGIN
R3
GIN1+
R2
GIN1-
R1
RIN-
T1
RIN+
T2
HSYNCI0
U1
VSYNCI0
U2
RX3CB
A15
RX3C
B15
RX30B
A14
RX30
B14
RX31B
A13
RX31
B13
RX32B
A12
RX32
B12
RX4CB
A11
RX4C
B11
RX40B
A10
RX40
B10
RX41B
A9
RX41
B9
RX42B
A8
RX42
B8
Sign
al I
nput
34UM65
1 6
ML_LANE_3-
AUX_CH-
ML_LANE_3+
ML_LANE_1-
ML_LANE_0+
CONFIG2
HOT_PLUG
GND_4
CONFIG1
GND_2
GND_1
RETURN
DP_PWR[3.3V]
ML_LANE_2+
ML_LANE_1+
GND_0
GND_3
ML_LANE_0-
AUX_CH+
ML_LANE_2-
HDMI2
EEPROM
.04
HDMI2
DP
HDMI1
HDMI1
EEPROM
[TVS DIODE FOR ESD PROTECTION]
HDMI2
Angle
Option: "25UM65/29UB65"
Location is rear
Option: "29UM65/34UM65"
Location is left side
THE
S
YMBO
L MA
RK O
F TH
IS S
CHEM
ETIC
DIA
GRAM
INC
ORPO
RATE
SSP
ECIA
L FE
ATUR
ES I
MPOR
TANT
FOR
PRO
TECT
ION
FROM
X-R
ADIA
TION
.FI
RE A
ND E
LECT
RICA
L SH
OCK
HAZA
RDS,
WHE
N SE
RVIC
ING
IF I
S ES
SENT
IAL
THAT
ONL
Y MA
NUFA
CTUR
ES S
PECI
FIED
PAR
TS B
E US
ED F
ORTH
E CR
ITIC
AL C
OMPO
NENT
S IN
THE
SYMB
OL M
ARK
OF T
HE S
CHEM
ETIC
.
SIGN2
SIGN1
DP_HPD
DVI_DET
HDMI2_SCL
HDMI2_SDA
EDID_WP
DVI_SCL
HDMI2_DET
DP_DET
DVI_SDA
DP_PLUG
HDMI1_SDA
HDMI1_HPD
HDMI1_SCL
+3.3V_SCALER
C207
0.1uF
16V
R200
10K
R201
1M
1%OSCI
OSCO
OSCI
OSCO
KEY1
KEY2
CS
SCK
WP_SPI
SDO
C213
0.1uF
SDI
+3.3V
C212
68pF
OPT
C211
68pF
OPT
C208
68pF
OPT
R21110K
+5V
C220
10uF
10V
C257
0.1uF
16V
C265
0.1uF
16V
+1.3V_MULTI
+1.3V_MULTI
C243
10uF
10V
+1.3V_MULTI
C231
0.1uF
16V
C248
10uF
10V
C266
10uF
10V
+1.3V_SCALER
C271
0.1uF
16V
+1.3V_MULTI
+3.3V_SCALER
C261
10uF
10V
+3.3V_SCALER
C267
0.1uF
16V
C245
10uF
10V
C262
10uF
10V
C252
0.1uF
16V
+3.3V_MULTI
C225
10uF
10V
C235
0.1uF
16V
C264
0.1uF
16V
C253
0.1uF
16V
C226
10uF
10V
C228
10uF
10V
C242
0.1uF
16V
C249
0.1uF
16V
+1.9V
C237
10uF
10V
+1.9V
C269
10uF
10V
C272
0.1uF
16V
L200
BLM18PG121SN1D
RED LED OPT
WLED_PDIM
WLED_ENABLE
C268
0.1uF
16V
R219
33
R220
33
C201
22pF
C200
22pF
HDMI1_DET
HP_DET
R231
10K
R207
10K
OPT
R236
10K
OPT
+3.3V_SCALER
+3.3V_SCALER
R237
10K
R238
10K
TXC2P
TXB4P
TXBCLN
TXD2N
TXA0N
TXD1P
TXA2N
TXD4P
TXA4N
TXC0N
TXBCLP
TXD4N
TXCCLP
TXB1P
TXB2N
TXC1N
TXDCLN
TXC0P
TXCCLN
TXBCLP
TXB2N
TXD2P
TXB1P
TXACLN
TXA0P
TXA2P
TXD3N
TXB2P
TXC3P
TXD0N
TXA0P
TXA1N
TXC1P
TXB4N
TXCCLN
TXC3N
TXB4P
TXD2N
TXB0P
TXD1P
TXC4N
TXC2N
TXA3N
TXC1P
TXA2P
TXA4P
TXB3P
TXB1N
TXB3N
P202
FI-RE41S-HF-J-R1500
1GND
2GND
3TXD4P
4TXD4N
5TXD3P
6TXD3N
7GND
8TXDCLP
9TXDCLN
10
GND
11
TXD2P
12
TXD2N
13
TXD1P
14
TXD1N
15
TXD0P
16
TXD0N
17
GND
18
GND
19
TXC4P
20
TXC4N
21
TXC3P
22
TXC3N
23
GND
24
TXCCLP
25
TXCCLN
26
GND
27
TXC2P
28
TXC2N
29
TXC1P
30
TXC1N
31
TXC0P
32
TXC0N
33
GND
34
NC
35
NC
36
NC
37
NC
38
NC
39
NC
40
NC
41
NC
42
TXBCLN
TXB1N
TXA0N
TXD2P
TXB0P
TXB3N
P201
FI-RE51S-HF-J-R1500
1+PANEL_PWR
2+PANEL_PWR
3+PANEL_PWR
4+PANEL_PWR
5NC
6GND
7GND
8GND
9GND
10
GND
11
TXB4P
12
TXB4N
13
TXB3P
14
TXB3N
15
GND
16
TXBCLP
17
TXBCLN
18
GND
19
TXB2P
20
TXB2N
21
TXB1P
22
TXB1N
23
TXB0P
24
TXB0N
25
Bit Select
26
NC
27
TXA4P
28
TXA4N
29
TXA3P
30
TXA3N
31
GND
32
TXACLP
33
TXACLN
34
GND
35
TXA2P
36
TXA2N
37
TXA1P
38
TXA1N
39
TXA0P
40
TXA0N
41
GND
42
NC
43
PWM_OUT
44
NC
45
LVDS Format
46
ODC Select 47
NC
48
NC
49
NC
50
NC
51
GND
52
GND
TXC4P
TXD3P
TXD3N
TXCCLP
TXB2P
TXC2P
TXDCLN
TXA1P
TXD4N
TXC0N
TXD3P
TXA1P
R221
10K
TXC3N
TXB4N
TXDCLP
TXD1N
TXB3P
TXB0N
TXC0P
TXACLP
TXC1N
TXD0P
TXD1N
TXD4P
TXC4N
TXC4P
TXA4N
TXC2N
TXA3N
TXD0P
TXACLP
+10V_PANEL
TXA3P
TXA4P
TXA1N
C216
10uF
25V
TXD0N
TXC3P
TXA2N
TXDCLP
TXA3P
TXACLN
TXB0N
R215
1K
R216
1K
+1.3V_MULTI
/FAULT
IC201
W25Q80BVSSIG
3%WP[IO2]
2DO[IO1]
4GND
1CS
5DI[IO0]
6CLK
7HOLD[IO3]
8VCC
BUZZER_PWM
WLED_ADIM
KEY2
KEY1
SDO
CS
SCK
WP_SPI
SDI
+3.3V_SCALER
+3.3V_SCALER
+3.3V_SCALER
+3.3V_SCALER
+3.3V_SCALER
+1.3V_SCALER
PD_CTRL
PANEL_ON
+1.9V
C202
0.1uF
R205
10K
1% R206
10K
1%
R204
1K
R202
1K
+1.3V_MULTI
C214
1uF
+1.3V_SCALER
P200
12507WR-08L
1+3.3V
2KEY1
3KEY2
4SCL
5SDA
6GND
7 8
9
3.3V_AMP_POWER_ON
HDMI2_HPD
DVI_HPD
C260
0.1uF
16V
P_LED
+3.3V_SCALER
+3.3V_MULTI
+3.3V_MULTI
X200
12MHz
L201
BLM18PG121SN1D
WHITE LED OPT
+5V
R203
4.7K
OPT
R208
4.7K
R209
4.7K
OPT
Q200
MMBT3904-(F)
E
B
C
P_LED
+3.3V
C203
68pF
D200
D201
D202
D203
IC100
NT68370(D VER.)
PC3/CEC
B2
PC0/CEC/SCK_O
B3
PF7/VBUS4/WD_I
D12
PA6/DDC_SCL3/RXD3
C11
PA7/DDC_SDA3/TXD3
D11
PF3/CD_SENSE4
A3
PD5/IR_PORT1/MCLK_O
A4
PE4/CBUS1/HPD1
C3
PF4/VBUS1
B4
PB4/DDC_SCL0/RXD0
C4
PB5/DDC_SDA0/TXD0
D3
PF0/CD_SENSE1
D4
PD4/IR_PORT3
E3
PE5/CBUS2/HPD2
F3
PF5/VBUS2
F4
PB6/DDC_SCL1/RXD1
G3
PB7/DDC_SDA1/TXD1
G4
PF1/CD_SENSE2
H3
PC7/IR_PORT2/SCK_I
H4
PA0/ADC4/PWMA
T3
PA1/ADC5/PWMB
T4
PC4/DDC_SCL4/RXD4
P3
PC5/DDC_SDA4/TXD4
P4
PD7
R4
RSTN
V3
OSCI
N1
OSCO
N2
OPT1
V1
OPT0
V2
PE2/DBC/PWMC/M2_SPI_CE3
AC16
PE3/PWMD/M2_SPI_CE4
AD17
PA2/ADC6/PWMC/DIN_19
AC17
PA3/ADC7/PWMD/DIN_18
AE17
PB2/ADC2/INTE2/DIN_21
AF17
PB3/ADC3/INTE3/DIN_20
AE18
P34/RXD5/DIN_16
AD18
P35/TXD6/DIN_15
AD19
PC6/AMUTE/M2_SPI_CE2/AO_IN/DIN_17
AC18
P30/RXD/AO_OUT/DIN_14
AF18
P31/TXD/AO_OUTB/DIN_13
AC19
PD2/M2_SPI_SO/SD_I/DIN_12
AE19
PD3/M2_SPI_CE1/WD_I/DIN_11
AE20
PD0/M2_SPI_CLK/SCK_I/DIN_10
AF19
PD1/M2_SPI_SI/DIN_9
AF20
SPI_CE
AD20
SPI_SO
AC20
SPI_CLK
AC21
SPI_SI
AD21
PE7/CBUS4
C12
PD6/DIN_VS
D13
PF2/CD_SENSE3/DIN_HS_CS
C13
PA5/DDC_SDA2/TXD2/DIN_HREF_DE
D14
PA4/DDC_SCL2/RXD2/DIN_0
C14
PE6/CBUS3
C15
PF6/VBUS3/SD_I
D15
PB1/ADC1/INTE1/DIN_3
C16
PB0/ADC0/INTE0/DIN_4
B16
PE1/ADDR1/DIN_1
A16
PE0/LPD_IN0/ADDR0
D17
PC2/DBC/PWMB/SD_O
C17
PC1/LPD_OUT/PWMA
B17
OUT_P
A20
OUT_N
B20
PG3/DIN_6/DUI_INTE
C20
PG2/DIN_5/DUI_SPI_SIO
D20
PG1/DIN_2/DUI_SPI_CE
A19
PG0/DIN_CK/DUI_SPI_CK
B19
PG7/DIN_7/DUO_INTE
C19
PG6/DIN_8/DUO_SPI_SIO
D19
PG5/DIN_23/DUO_SPI_CE
A18
PG4/DIN_22/DUO_SPI_CK
B18
DU_VS/PA4
D18
DU_DE/PA5
C18
DU_FAST_MUTE/PD0
A17
HI_M_S_SEL
J3
HI_SPI_CK/P35
J4
HI_INTE/PA2
K3
SPI_CE3/P34
K4
SPI_CE2/P31
L3
SPI_CE1/P30
L4
SPI_SIO4/PB3
M3
SPI_SIO3/PB2
M4
SPI_SIO2/PB1
N3
SPI_SIO1/PB0
N4
IC100
NT68370(D VER.)
TXA0N
N24
TXA0P
N23
TXA1N
N26
TXA1P
N25
TXA2N
P24
TXA2P
P23
TXACKN
P26
TXACKP
P25
TXA3N
R24
TXA3P
R23
TXA4N
R26
TXA4P
R25
TXB0N
T24
TXB0P
T23
TXB1N
T26
TXB1P
T25
TXB2N
U24
TXB2P
U23
TXBCKN
U26
TXBCKP
U25
TXB3N
V24
TXB3P
V23
TXB4N
V26
TXB4P
V25
TXC0N
W24
TXC0P
W23
TXC1N
W26
TXC1P
W25
TXC2N
Y24
TXC2P
Y23
TXCCKN
Y26
TXCCKP
Y25
TXC3N
AA24
TXC3P
AA23
TXC4N
AA26
TXC4P
AA25
TXD0N
AB24
TXD0P
AB23
TXD1N
AB26
TXD1P
AB25
TXD2N
AC24
TXD2P
AC23
TXDCKN
AC26
TXDCKP
AC25
TXD3N
AD24
TXD3P
AD23
TXD4N
AD26
TXD4P
AD25
DP_TX0N
C25
DP_TX0P
C26
DP_TX1N
D25
DP_TX1P
D26
DP_TX2N
E25
DP_TX2P
E26
DP_TX3N
F25
DP_TX3P
F26
DP_AUXN
G25
DP_AUXP
G26
DP_TXHDP
G24
DPTX_OSCI
H24
DPTX_OSCIO
J24
EDP_TX0P
H26
EDP_TX0N
H25
EDP_TX1P
J26
EDP_TX1N
J25
EDP_TX2P
K26
EDP_TX2N
K25
EDP_TX3P
L26
EDP_TX3N
L25
EDP_AUXN
M25
EDP_AUXP
M26
EDP_TXHDP
K24
EXT_SWING
AE25
3P_OPEN
AF21
3N_OPEN
AE21
2P_OPEN
AF22
2N_OPEN
AE22
1P_OPEN
AF23
1N_OPEN
AE23
0P_OPEN
AF24
0N_OPEN
AE24
LOCKN_OPEN
AD22
HTPDN_OPEN
AC22
IC100
NT68370(D VER.)
CVDD_1
G17
CVDD_2
G18
CVDD_3
G19
CVDD_4
H19
CVDD_5
J19
CVDD_6
K19
CVDD_7
L19
CVDD_8
M19
CVDD_9
N19
CVDD_10
P19
CVDD_11
R19
CVDD_12
T19
CVDD_13
U19
CVDD_14
V17
CVDD_15
V18
CVDD_16
V19
VDD12RX_1
G11
VDD12RX_2
H10
VDD33RX_1
G9
VDD33RX_2
H9
VMM_ADC12_1
M9
VMM_ADC12_2
N9
VCCA/VCCD_1
V9
VCCA/VCCD_2
V10
VCC_CLK
V12
VX1_EXT12_1
W18
VX1_EXT12_2
W19
APR1_V12_1
J9
APR1_V12_2
J10
APR1_V12_3
K9
APR1_V12_4
K10
DP_AVDD_PLL_1
J21
DP_AVDD_PLL_2
K21
DP_AVDD_1
J20
DP_AVDD_2
K20
TVCC33_1
E11
TVCC33_2
E12
TVCC33_3
E13
VCC_LDO33
M7
VCC_ADC33
M8
MPLL33
N8
OSC_VCC33
N7
VDD_DLL
P7
VCCA_LVDS_1
R21
VCCA_LVDS_2
T21
DP_AVDD_33_1
G20
DP_AVDD_33_2
H20
VCC33_SSCK
F20
OSC_MVCC3IO
D21
DVDD_1
E15
DVDD_2
E16
DVDD_3
E17
VDD_VBYONE_33V_1
V20
VDD_VBYONE_33V_2
W20
V12T_1
F10
V12T_2
F11
V12T_3
G10
VDD_CORE/VDD_MMU_1
U7
VDD_CORE/VDD_MMU_2
U8
VDD_CORE/VDD_MMU_3
V7
VDD_CORE/VDD_MMU_4
V8
VDD_CORE/VDD_MMU_5
W7
VDD_CORE/VDD_MMU_6
W8
VDD_CORE/VDD_MMU_7
W9
VDD_CORE/VDD_MMU_8
W10
VDD_CORE/VDD_MMU_9
W11
VDD_CORE/VDD_MMU_10
W12
VDD_CORE/VDD_MMU_11
W13
VDD_CORE/VDD_MMU_12
W14
VDD_CORE/VDD_MMU_13
W15
VDD_CORE/VDD_MMU_14
W16
VDD_CORE/VDD_MMU_15
W17
VDD_CORE/VDD_MMU_16
Y7
VDD_CORE/VDD_MMU_17
Y8
VDD_CORE/VDD_MMU_18
Y9
VDD_CORE/VDD_MMU_19
Y10
VDD_CORE/VDD_MMU_20
Y11
VDD_CLK
Y12
MVREF
Y6
GND_1
H12
GND_2
H13
GND_3
H14
GND_4
H15
GND_5
H16
GND_6
H17
GND_7
H18
GND_8
J12
GND_9
J13
GND_10
J14
GND_11
J15
GND_12
J16
GND_13
J17
GND_14
J18
GND_15
K12
GND_16
K13
GND_17
K14
GND_18
K15
GND_19
K16
GND_20
K17
GND_21
K18
GND_22
L12
GND_23
L13
GND_24
L14
GND_25
L15
GND_26
L16
GND_27
L17
GND_28
L18
GND_29
M12
GND_30
M13
GND_31
M14
GND_32
M15
GND_33
M16
GND_34
M17
GND_35
M18
GND_36
N12
GND_37
N13
GND_38
N14
GND_39
N15
GND_40
N16
GND_41
N17
GND_42
N18
GND_43
P12
GND_44
P13
GND_45
P14
GND_46
P15
GND_47
P16
GND_48
P17
GND_49
P18
GND_50
R12
GND_51
R13
GND_52
R14
GND_53
R15
GND_54
R16
GND_55
R17
GND_56
R18
GND_57
T12
GND_58
T13
GND_59
T14
GND_60
T15
GND_61
T16
GND_62
T17
GND_63
T18
GND_64
U12
GND_65
U13
GND_66
U14
GND_67
U15
GND_68
U16
GND_69
U17
GND_70
U18
GND_71
Y3
GND_72
AA3
GND_73
AB3
GND_74
AC3
GND_75
AD3
GND_76
AD4
GND_77
AD5
GND_78
AD6
GND_79
AD7
GND_80
AD8
GND_81
AD9
GND_82
AD10
GND_83
AD11
GND_84
AD12
GND_85
AD13
GND_86
AD14
GND_87
AD15
GND_88
AD16
ADC_GND
N10
OSC_GND
P10
ITLC
R960
10K
+3.3V
R961
0OPT
R962
0
ITLC
2 6
GPIO
/Sca
ler
Powe
r/LV
DS
FLAH
8MBIT
HIGH-10bit
NC-8bit
Control key
LVDS JACK1
LVDS JACK2
If h/sink applied,
X200 shall move away h/sink area
Flash shall be chagned 16Mbit
when scaler being revised
5V_DET_INT
34UM65
High : Interlace mode
Low : Normal mode
THE
S
YMBO
L MA
RK O
F TH
IS S
CHEM
ETIC
DIA
GRAM
INC
ORPO
RATE
SSP
ECIA
L FE
ATUR
ES I
MPOR
TANT
FOR
PRO
TECT
ION
FROM
X-R
ADIA
TION
.FI
RE A
ND E
LECT
RICA
L SH
OCK
HAZA
RDS,
WHE
N SE
RVIC
ING
IF I
S ES
SENT
IAL
THAT
ONL
Y MA
NUFA
CTUR
ES S
PECI
FIED
PAR
TS B
E US
ED F
ORTH
E CR
ITIC
AL C
OMPO
NENT
S IN
THE
SYMB
OL M
ARK
OF T
HE S
CHEM
ETIC
.DDR
MDQ[26]
MDQ[20]
MDQ[23]
MDQ[27]
MDQ[19]
MDQ[28]
MA[7]
MDQ[18]
MDQ[21]
MA[0]
MA[12]
MDQ[24]
MDQ[27]
MA[6]
MA[4]
MDQ[21]
MDQ[31]
MA[0]
MA[8]
MDQ[29]
MDQ[20]
MA[1]
MA[12]
MDQ[25]
MDQ[22]
MA[10]
MA[11]
MDQ[28]
MDQ[19]
MA[7]
MA[5]
MDQ[22]
MDQ[13]
MA[2]
MDQ[17]
MA[1]
MDQ[30]
MDQ[4]
MDQ[29]
MDQ[17]
MDQ[0]
MDQ[30]
MDQ[13]
MA[9]
MDQ[1]
MDQ[16]
MDQ[10]
MDQ[16]
MA[3]
MDQ[2]
MDQ[11]
MDQ[23]
MA[6]
MDQ[3]
MDQ[0]
MDQ[12]
MDQ[24]
MBA[0]
MDQ[5]
MDQ[15]
MA[8]
MDQ[6]
MDQ[14]
MBA[1]
MDQ[7]
MDQ[5]
MA[4]
MDQ[8]
MDQ[9]
MBA[1]
MA[3]
MDQ[6]
MDQ[9]
MBA[0]
MDQ[18]
MA[9]
MDQ[8]
MDQ[10]
MDQ[26]
MA[5]
MDQ[2]
MDQ[11]
MA[11]
MDQ[25]
MDQ[7]
MDQ[12]
MDQ[4]
MDQ[14]
MDQ[1]
MDQ[15]
MDQ[3]
MA[2]
MDQ[31]
MA[10]
MA[0]
MA[1]
MA[2]
MA[3]
MA[4]
MA[5]
MA[6]
MA[7]
MA[8]
MA[9]
MA[10]
MA[11]
MA[12]
MBA[0]
MBA[1]
R439
22
MA[0-12]
MCKE
R425
22
MCLK1P
+1.9V
C402
0.1uF
R434
22
ODT
MDQS2N
R412
22
R443
22
+1.9V
+1.9V
MDQ[16-31]
C406
0.1uF
R421
22
MRASN
MRASN
+1.9V
R430
22
MDQS2P
R407
22
R417
22
MCLK0P
MDQS1N
R438
22
+1.9V
R426
22
MDQS1P
MCASN
MDQS0P
MBA[0-1]
MA[0-12]
R404
22
MCKE
R413
22
R442
22
MBA[0-1]
R422
22
MDQS2P
MCLK0N
MWEN
C408
0.1uF
R431
22
R409
22
MCSN
R418
22
R469
100
R437
22
MDQS3N
C404
0.1uF
MDQS3N
R427
22
C405
0.1uF
C407
0.1uF
MCSN
C409
0.1uF
MCSN
R405
22
R414
22
R441
22
MDQS2N
C403
10uF
10V
MCKE
R423
22
MDQ[0-15]
MDQS0N
MDQS1P
MWEN
R400
100
MDQS0N
R432
22
R410
22
+1.9V
R419
22
R436
22
MBA[0-1]
MRASN
MCLK1N
MWEN
MCLK0P
R428
22
C400
0.1uF
MDQS3PC419
0.1uF
R406
22
MCASN
R415
22
R440
22
MDQ[16-31]
MDQ[0-15]
MCASN
R424
22
MCLK0N
C418
0.1uF
MDQS3P
MCLK1N
R433
22
R411
22
R435
22
+1.9V
R420
22
MDQS0P
MCLK1P
MA[0-12]
ODT
R429
22
MDQS1N
ODT
R408
22
C401
0.1uF
R416
22
R473
22 OPT
C410
0.1uF
C412
0.1uF
C413
0.1uF
C415
0.1uF
C414
0.1uF
+1.9V
C417
0.1uF
C416
0.1uF
C411
10uF
10V
R402
10K1%
R403
10K1%
R471
10K1%
R472
10K1%
R475
0R474
0
IC100
NT68370(D VER.)
MDQ31
AE2
MDQ30
AB2
MDQ29
AE3
MDQ28
AA2
MDQ27
AA1
MDQ26
AF3
MDQ25
AB1
MDQ24
AF2
MDQ23
AF4
MDQ22
Y1
MDQ21
AF5
MDQ20
W1
MDQ19
W2
MDQ18
AE5
MDQ17
Y2
MDQ16
AE4
MDQ15
AE12
MDQ14
AF9
MDQ13
AE13
MDQ12
AF8
MDQ11
AE8
MDQ10
AF13
MDQ9
AE9
MDQ8
AF12
MDQ7
AF14
MDQ6
AE7
MDQ5
AF15
MDQ4
AE6
MDQ3
AF6
MDQ0
AE14
MDQ1
AF7
MDQ2
AE15
MDQS3B
AD2
MDQS3
AD1
MDQS2B
AC2
MDQS2
AC1
MDQS1B
AF11
MDQS1
AE11
MDQS0B
AF10
MDQS0
AE10
MBA1
AB10
MBA0
AB9
MA12
AB5
MA11
AC14
MA10
AC5
MA9
AC4
MA8
AB14
MA7
AB6
MA6
AC13
MA5
AB8
MA4
AB13
MA3
AB7
MA2
AC12
MA1
AC6
MA0
AB12
MCSN
AC11
MCKE
AC7
MRASN
AC10
MCASN
AC9
MWEN
AC8
MCLK1-
AC15
MCLK1+
AB15
MCLK0-
AF16
MCLK0+
AE16
ODT
AB11
PHY_TM
AB4
IC400
H5PS1G63KFR-G7C
J2
VREF
J8
CK
H2
VSSQ2
B7
UDQS
N8
A4
P8
A8
L1
BA2
L2
BA0
R8
NC3
K7
RAS
F8
VSSQ3
F3
LDM
P3
A9
M3
A1
N3
A5
K8
CK
R3
NC5
L3
BA1
J7
VSSDL
L7
CAS
F2
VSSQ4
B3
UDM
M2
A10/AP
K2
CKE
R7
NC6
M7
A2
N7
A6
M8
A0
J1
VDDL
K3
WE
E8
LDQS
P7
A11
K9
ODT
A2
NC1
N2
A3
P2
A7
H8
VSSQ1
F7
LDQS
A8
UDQS
R2
A12
L8
CS
E2
NC2
E7
VSSQ5
D8
VSSQ6
D2
VSSQ7
A7
VSSQ8
B8
VSSQ9
B2
VSSQ10
P9
VSS1
N1
VSS2
J3
VSS3
E3
VSS4
A3
VSS5
G9
VDDQ1
G7
VDDQ2
G3
VDDQ3
G1
VDDQ4
E9
VDDQ5
C9
VDDQ6
C7
VDDQ7
C3
VDDQ8
C1
VDDQ9
A9
VDDQ10
R1
VDD1
M9
VDD2
J9
VDD3
E1
VDD4
A1
VDD5
B9
DQ15
B1
DQ14
D9
DQ13
D1
DQ12
D3
DQ11
D7
DQ10
C2
DQ9
C8
DQ8
F9
DQ7
F1
DQ6
H9
DQ5
H1
DQ4
H3
DQ3
H7
DQ2
G2
DQ1
G8
DQ0
IC401
H5PS1G63KFR-G7C
J2
VREF
J8
CK
H2
VSSQ2
B7
UDQS
N8
A4
P8
A8
L1
BA2
L2
BA0
R8
NC3
K7
RAS
F8
VSSQ3
F3
LDM
P3
A9
M3
A1
N3
A5
K8
CK
R3
NC5
L3
BA1
J7
VSSDL
L7
CAS
F2
VSSQ4
B3
UDM
M2
A10/AP
K2
CKE
R7
NC6
M7
A2
N7
A6
M8
A0
J1
VDDL
K3
WE
E8
LDQS
P7
A11
K9
ODT
A2
NC1
N2
A3
P2
A7
H8
VSSQ1
F7
LDQS
A8
UDQS
R2
A12
L8
CS
E2
NC2
E7
VSSQ5
D8
VSSQ6
D2
VSSQ7
A7
VSSQ8
B8
VSSQ9
B2
VSSQ10
P9
VSS1
N1
VSS2
J3
VSS3
E3
VSS4
A3
VSS5
G9
VDDQ1
G7
VDDQ2
G3
VDDQ3
G1
VDDQ4
E9
VDDQ5
C9
VDDQ6
C7
VDDQ7
C3
VDDQ8
C1
VDDQ9
A9
VDDQ10
R1
VDD1
M9
VDD2
J9
VDD3
E1
VDD4
A1
VDD5
B9
DQ15
B1
DQ14
D9
DQ13
D1
DQ12
D3
DQ11
D7
DQ10
C2
DQ9
C8
DQ8
F9
DQ7
F1
DQ6
H9
DQ5
H1
DQ4
H3
DQ3
H7
DQ2
G2
DQ1
G8
DQ0
DDR
4 6
Close to DDR Power Pin
DDR2 1.8V By CAP - Place these Caps near Memory
Close to DDR Power Pin
DDR
1GBIT
34UM65
THERMAL
THE
S
YMBO
L MA
RK O
F TH
IS S
CHEM
ETIC
DIA
GRAM
INC
ORPO
RATE
SSP
ECIA
L FE
ATUR
ES I
MPOR
TANT
FOR
PRO
TECT
ION
FROM
X-R
ADIA
TION
.FI
RE A
ND E
LECT
RICA
L SH
OCK
HAZA
RDS,
WHE
N SE
RVIC
ING
IF I
S ES
SENT
IAL
THAT
ONL
Y MA
NUFA
CTUR
ES S
PECI
FIED
PAR
TS B
E US
ED F
ORTH
E CR
ITIC
AL C
OMPO
NENT
S IN
THE
SYMB
OL M
ARK
OF T
HE S
CHEM
ETIC
.
JK500
KJA-DC-1-0032
124
+10V_PANEL
+19V
L519
BLM18PG121SN1D
C500
68uF
35V
+1.9V
L502
BLM18PG121SN1D
C579
10uF
25V
+19V
C567
0.1uF
50V
C526
10uF
10V
L515
10uH
C583
0.1uF
50V
R562
33K
R565
47K
L512
BLM18PG121SN1D
C566
0.1uF
16V
+5V
R566
47K
1%
C525
10uF
10V
R507
15K
1%
C544
0.1uF
50V
+19V
C573
0.1uF
50V
C571
10uF
25V
C560
10uF
10V
R522
33K
C556
0.1uF
16V
L513
10uH
R563
100K
R559
100K
R521
33K
C555
0.1uF
16V
C539
10uF
25V
+19V
PANEL_ON
C543
0.1uF
50V
C541
0.1uF
50V
R517
47K
C564
0.1uF
16V
C504
10uF
10V
L511
10uH
C502
10uF
10V
R519
33K
L500
BLM18PG121SN1D
R524
33K
C503
10uF
10V
R505
100K
C501
10uF
10V
R520
33K
C565
0.1uF
16V
+1.3V_SCALER
R571
33K
1%
R529
10K
R518
47K
R500
8.2K
1%
R523
47K
R509
10K
R508
47K
R504
11K
1%
R502
10K
1%R561
10K
1%
R560
33K
1%
IC500
MP2315GJ
3SW
2IN
4GND
1AAM
5BST
6EN/SYNC
7VCC
8FB
IC510
MP2315GJ
3SW
2IN
4GND
1AAM
5BST
6EN/SYNC
7VCC
8FB
IC509
MP2315GJ
3SW
2IN
4GND
1AAM
5BST
6EN/SYNC
7VCC
8FB
IC506
MP2315GJ
3SW
2IN
4GND
1AAM
5BST
6EN/SYNC
7VCC
8FB
IC505
MP2315GJ
3SW
2IN
4GND
1AAM
5BST
6EN/SYNC
7VCC
8FB
C538
10uF
25V
C536
10uF
25V
+5V
+5V
R525
68
R526
68
R527
68
R528
68
R557
68
R512
33K
R513
33K
L514
15uH
L505
4.7uH
C540
0.1uF
16V
C530
0.1uF
16V
C533
0.1uF
16V
C537
0.1uF
16V
C553
0.1uF
16VC546
0.1uF
16V
R533
33K
OPT
R535
33K
OPT
R543
33K
OPT
C527
0.1uF
16V
C570
10uF
10V
C506
10uF
10V
C505
10uF
10V
C511
0.1uF
16V
C510
0.1uF
16V
Q505
MMBT3904(NXP)
E
B
C
PD_CTRL
R555
10K
+5V
R556
47K
C507
0.1uF
16V
R558
100K
C514
10uF
10V
Q506
AO3438
G
D S+1.3V_MULTI
R579
1K
1.9V_PD
R506
10K
1.9V_PD
+1.3V_SCALER
C519
10uF
10V
OPT
+3.3V
L510
BLM18PG121SN1D
R501
12K
1%
Q503
MMBT3904(NXP)
OPT
E
B
C
C568
10uF
10V
OPT
L516
BLM18PG121SN1D
OPT
R564
10K
OPT
C512
1uF
10V
OPT
R568
10K
R567
10K
OPT
R570
1K
OPT
3.3V_AMP_POWER_ON
C509
10uF
10V
OPTR511
1
1/10W
1608
OPT
+5V
+3.3V_AMP
R547
1.5K
R576
100K
C523
4700pF
OPT
L503
BLM18PG121SN1D
WLED_ENABLE
R510
1K
R569
24K
C524
33uF
100V
L506
33uH
C517
1000pF
50V
D500
BR210
100V
C520
1uF
50V
OPT
IC501
DT1643S
3EN
2VREF1
4PDIM
1VIN
6LS1
5RISET
7LS2
8LGND
9LS3
10
LS4
11
OVP
12
RT
13
COMP
14
CS
15
NDRV
16
VREF2
17
[EP]GND
Q500
AOD478
SD
G
R532
100K
C522
10uF
25V
C515
1uF
25V
+19V
R573
270K
C521
1uF
50V
OPT
R572
1.5K
C508
68pF
50V
P501
12507WR-06L
1
2
3
4
5
6
7
WLED_PDIM
R575
100K
+19V
C528
33uF
100V
R546
39K
C516
1uF
25V
R577
0.075
R531
100K
C513
1000pF
50V
L504
BLM18PG121SN1D
+3.3V_SCALER
R580
33
R574-*1
200K
25inch
R503
16K
1%
JP920
JP921
JP923
JP924
JP925
JP926
JP934
JP935
JP936
JP937
+3.3V_SCALER
Q501
AO3438
G
D S
C531
10uF
10V
+3.3V_MULTI
C529
10uF
10V
OPT
R582
10K
R583
10K
R581
10K
+5V
Q507
MMBT3904(NXP)
E
B
C
WLED_ADIM
IC502
AZ1117H-3.3
OPT 1
ADJ/GND
2OUTPUT
3INPUT
C518
1uF
C532
1uF
16V
ZD501
2.5V
ZD500
5V
ZD502
2.5V
Q504
AO3407B
OPT G
DS
L520BLM18PG121SN1D
+3.3V_AMP
R514
100K
1%
R515
20K
1%
R516
10K
1%
R530
100K
R544
30K
1%
R545
13K
1%
R574
240K
29inch
POWE
R/DR
IVER
5 6
0.8A(CAS)
Power
Jack
Scaler & DDR
3A
3A
3A
3A
3A
0.7A
0.3A
Voltage 1.3V
0.4A
130712
+3.3V_AMP consump about 10mA in DC off or Slee mode
[Ready]3.3V_AMP
High
Low
High
Low
1.3V(on)
0V(off)
29": 2.6A
LED DRIVER
.0348
For 25inch
Jig-Point_GND
34UM65
DC Rated Current spec: 4A
THE
S
YMBO
L MA
RK O
F TH
IS S
CHEM
ETIC
DIA
GRAM
INC
ORPO
RATE
SSP
ECIA
L FE
ATUR
ES I
MPOR
TANT
FOR
PRO
TECT
ION
FROM
X-R
ADIA
TION
.FI
RE A
ND E
LECT
RICA
L SH
OCK
HAZA
RDS,
WHE
N SE
RVIC
ING
IF I
S ES
SENT
IAL
THAT
ONL
Y MA
NUFA
CTUR
ES S
PECI
FIED
PAR
TS B
E US
ED F
ORTH
E CR
ITIC
AL C
OMPO
NENT
S IN
THE
SYMB
OL M
ARK
OF T
HE S
CHEM
ETIC
.AUDIO
+5V
HP_R_OUT
R616
0
IC906
AZ7029RTRE1OPT
2
GND
3OUT
1VCC
R617
0
+3.3V_AMP
+3.3V_AMP
R614
1K
R618
0
R643
10K
OPT
C672
0.1uF
16V
OPT
JK601
PEJ027-03
6B
T_TERMINAL2
7B
B_TERMINAL2
5T_SPRING
4R_SPRING
7A
B_TERMINAL1
6A
T_TERMINAL1
3E_SPRING
R602
100K
HP_L_OUT
HP_DET
HP_R_OUT
R606
1K
R605
1K
R635
1K
OPT
HP_L_OUT
C613
10uF
10V
C616
0.1uF
/FAULT
+3.3V_SCALER
R636
2.2K
OPT
C663
0.1uF
16V
OPT
C618
10uF
10V
+3.3V_SCALER
C600
1uF
10V
IC100
NT68370(D VER.)
AUDIO_VDD
C22
I2S3/AIN2R
B22
I2S2/AIN2L
A22
I2S1/AIN1R
B23
I2S0/AIN1L
A23
WD
C24
SCK/AOUT_R
A24
MCLK/AOUT_L
B24
SPDIF
B25
AUDIO_GND
B21
AUDIO_CEXT2
A21
D604
OPT
ZD606
5.6V
OPT
ADMC 5M 02 200L
ZD604
5.6V
OPT
ADMC 5M 02 200L
C673
220uF
16V
C674
220uF
16V
R615
10
R609
10
C601
2200pF
50V
C610
2200pF
50V
R958
100
R959
100
5 5
Headphone
HEADPHONE JACK
[Divide voltage]
3.4375V
[Ready]Pop killer
Votlage
Detector
29UM55