MCS-51 Writer
Unit back view
Note
DC 12V input socket
Power switch USB port (B type)
MCS-51 Writer main unit x1, USB cable x1, adaptor x1, PC Software, drivers and manuals on CD-ROM x1
Introduction
Main unit USB cableDC 12V/500mA
Adaptor
Unit top view
1. It is preferred to use an internal USB port of your PC. External USB ports are not recommended because of shared bandwidth and possible compatibility issues of other USB devices.
2. Set Font Size to [small fonts] (96 dpi) to have the optimal display.
Textool handler
IC package diagram
Textool
MC
S-5
1 W
riter Illu
stra
tion
Devices Supported
ATMEL
HYUNDAI
INTEL
AT89C51AT89C52AT89LV51AT89LV52AT89C55AT89LV55AT89C51RCAT89C55WDAT89S51AT89S52AT89S53AT89LS51AT89LS52AT89LS53AT89S8252AT89LS8252
GMS97C51GMS97C52GMS97C54GMS97C56GMS97C58GMS97L51GMS97L52GMS97L54GMS97L56GMS97L58
87C51FA87C51FB87C51FC87C51RA87C51RB87C51RC87C5287C5487C58
ISSI
TEMIC
WINBOND
IS89C51IS89C52IS89C54IS89C58IS89C64IS89E54IS89E58IS89E64IS89LV51IS89LV52IS89C51AIS89C52AIS89LV51AIS89LV52A
TSC87C51TSC87C52
W77E58W77LE58W78E51W78E51BW78E52W78E52BW78E54W78E54BW78E58W78LE51W78LE52W78LE54W78E516W78E516BW78E62W78E62BW78LE516W78LE58
PHILIPS
SST
P89C51UBP89C52UBP89C54UBP89C58UBP89C51RA+P89C51RB+P89C51RC+P89C51RD+P89C51RB2HP89C51RC2HP89C51RD2HP89C51RA2P89C51RB2P89C51RC2P89C51RD2P89C51X2P89C52X2P89C54X2P89C58X2P89C51BP89C52BP89C54BP89C58BP89C660P89C662P89C664P89C668P89C138MBP89C238MBP89C838MB
SST89C54SST89C58SST89F54SST89F58
Install software and driver1. Set Font Size to [small fonts] (96 dpi) to have the optimal display. 1.1 Click the right button on the desktop. -> Select the [Properties] at the bottom of the function menu. 1.2 Select [Settings] and then click the [Advanced] to set Font Size.2. Install the software before connecting the MCS-51 Writer to the PC. 2.1 Insert the software CD into your CD-ROM drive. Normally the installation program will start automatically (if Auto Run is enabled for your CD-drive). Follow the instructions to complete installation. 2.2 If Auto Run doesn't work, click [Setup.exe] in the CD directory to start the installation.3. Install the driver for the MCS-51 Writer hardware. 3.1 Make sure the MCS-51 Writer power is [OFF]. Connect the power adapter to the MCS-51 Writer and a power outlet. 3.2 Connect the USB cable to PC USB port and to the programmer USB port. 3.3 Turn the MCS-51 Writer power to [ON]. Windows will now start the [Found New Hardware Wizard]. 3.4 Install Hardware Device Driver -> Search for a suitable driver for my device (recommended) 3.5 Select Optional search locations -> CD-ROM drives 3.6 Driver Files Search Result -> Windows will find a driver for this device ...\driver\flashwriter.inf 3.7 Click [Finish] in the Found New Hardware Wizard
The MCS-51 Writer software and drivers have now been installed and the unit is ready to work.
LEAP Electronic Co., Ltd.Tel : + 886-2-2999 1860Fax : + 886-2-2999 9873http : //www.leap.com.twEmail: [email protected]
[3.3] [3.4] [3.5]
[3.7][3.6]
MC
S-5
1 W
riter In
sta
llatio
n
8bits HEX display 16bits HEX display Buffer & file information
Source file editing
IC manufacturer, type number
Run
Stop
Device verifyCheck SUM
Programming status
Programming source
Select IC number
Load file
Save file
Operation window
Exit program
Load from PC Verify source IC
Read fromsource IC
Edit file
Save file
Erase Blank check
Program Verify Protect /security
Progress bar
Program process & options
Address of dataClick and enter new address.
ASCII code DisplayClick to enter text.
HEX code Display Click to enter hexadecimal data.
Exit edit window
Get data blockchecksum
Data block - FillData block -Move/Copy/Swap
Confirm changes
Cancel changes
Set data blockrange by load file size
Set data block range by maximum size of buffer
Set data blockrange by selected IC size
MC
S-5
1 W
riter O
pe
ratio
n